Search Results

Search found 11100 results on 444 pages for 'normal distribution'.

Page 223/444 | < Previous Page | 219 220 221 222 223 224 225 226 227 228 229 230  | Next Page >

• Problems installing Linux to IDE connected compact flash card

  - by mathematician1975

  I have been trying to install Ubuntu on some hardware (Netcom NC-499 board that contains a Vortex86DX processor). I am trying to install to a compact flash card attached to the board via an IDE adaptor, the aim being that the board will boot up and simply treat the compact flash like a normal hard drive. The processor vendor claims support for Ubuntu 10.04 but I am having problems installing it onto the card. I have been trying using a USB CD-ROM drive and the standard .iso image from the ubuntu site (md5 checksum works out fine so no problem there) but I have had no success at all. I have been able to do this with Ubuntu 8.04 but with no other version (9.04 and 10.04 desktop and alternative discs all fail). My question is what other options are available to me to try and install this? I have googled myself apart trying to find out but other than a few sites describing USB based installs using flash memory sticks for very specific hardware, I have found no useful info at all. Any suggestions will be gratefully received.

  Read the article

• Easy Deployment Split Tunnel VPN Connection

  - by Joey Harris

  I was wondering if anybody could offer some insight as to how I can mass deploy VPN connection settings that support split tunneling. It has to work on both Mac and Windows systems though if a script is used, it obviously can be 2 separate scripts for both platforms. I will be setting up a Windows server with a file server and Exchange server and to access the file server I will have the clients go through VPN because we will have sensitive data. I don't want the servers network to be bogged down with the clients normal internet traffic so I will be needing some way to setup split tunneling on the clients without them having to put in a few commands every time to setup the static routes. Ive looked at Cisco VPN client but I want to try and stick with windows RRAS and avoid buying a Cisco VPN endpoint. Im basically looking for a good VPN client that can support split tunneling and mass deployment.

  Read the article

• How can I use Windows Firewall to only permit the Windows Update service to make an outbound connection?

  - by microsmash

  I'm trying to tailor my Windows Firewall settings (using the Windows Firewall with Advanced Security console) to only permit programs that need to access the Internet with an outbound connection to do so. This works fine for normal applications as I can just allow the program, but services that load in the svchost.exe process are a problem. The only services I actually need to give access to are Windows Update and the Background Intelligent Transfer Service (and even that, I would only like Windows Update to be able to submit jobs to, but that's another issue.) Is there a method to only allow these to be permitted an outbound connection, and not any of the other services loaded in svchost?

  Read the article

• Connecting a Mac to the office network

  - by user36501

  Hi All, I am busy preparing to start working with a Mac at work - in addition to my old PC. Just wondered, is it difficult to setup the Mac to run on the office network - i.e. does it need any special settings or servers or anything like that? and also printers...can I use the network printer as normal. I am just pottrying to think ahead of any ential issues. Also share drives...will I be able to access share drives and my backups to these shares drives - all a bit daunting! Btw in case you didn't notice I am a Mac Nube lol

  Read the article

• Linux - Debian - Original groups that a user is in

  - by Auxiliary

  This is embarrassing; I used the usermod command to add myself to the disk group. However I forgot to use the append option! so I'm not a member of any of the groups that I was originally, now terminal says that I'm not even a sudoer (How rude!). So the question is: What are the original groups that a normal Administrator type of user is in? BTW, I am using Linux Mint Debian Edition (LMDE). Any help is appreciated.

  Read the article

• How to save Word documents as HTML to be viewed in Firefox

  - by private_meta

  I'm in need for saving a Word document as HTML. It has some background images, other images, texts, ... It opens correctly in Internet Explorer, but how can I save a word doc as HTML so that Firefox and other current browsers render it correctly? All images are missing in the document. I looked through the generated html document, but the paths for the images appear to be correct. Any idea? Things like "Don't save docs as html" won't be helpful here. Edit: To make myself clear, the normal "Save as HTML" doesn't cut it, the result is broken in any browser other than Internet Explorer. Edit 2: What I'm using is Word 2010 and Firefox 4. I also tried rendering it in the latest Chrome version, which failed as well. I used different compatibility settings for saving as html, it did not help

  Read the article

• powertop keeps telling me to turn off the same thing, over and over

  - by Rory McCann

  I am running an ubuntu lucid laptop on battery. I want to make my power last as long as possible. Aswell as the normal things like turn down screen brightness, and turn off wifi, I'm using powertop. It will sometimes tell me things, e.g.: Suggestion: Enable USB autosuspend by pressing the U key OK, I press the U key to do that. However a few minutes later it will give me the same suggestion, it's as if it never enabled USB autosuspend the first time. It does this for other things aswell, not just USB autosuspend. e.g. it'll give me this message frequently: An audio device is active 100.0% of the time: hwC0D1 LSI ID 1040 Q - Quit R - Refresh A - Turn HD audio powersave on Is there anything I can do to make these choices 'stick'? Or do I have some unfortunatle hardware that won't obey linux? (If so, is there any way to confirm this?)

  Read the article

• Thinkpad CPU temperature reaches 100°C after 10 minutes of heavy use

  - by Nicolas Raoul

  Less than two years ago, I bought a Lenovo Thinkpad R500. When using the CPU heavily, it sometimes decides to reboot. I am using Linux, and a widget shows me the CPU temperature. The PC usually reboots when the temperature of the first core gets over 100°C Since I switched from Ubuntu 2010.10 32bit to Ubuntu 2011.04 64bit, it crashes much more often. I survive using these techniques: When in the office, I use a laptopcooler. When outside, I underclock to 800 MHz, by doing so it does not get too warm. QUESTION: Is it normal that a Thinkpad crashes if the CPU is at 100% for more than 10 minutes? How can I use the full power of my computer, for instance when showing CPU-hungry business intelligence tools to clients? The computer does not really feel that hot. Maybe the sensor itself is reporting wrong temperatures? Can I tell the BIOS to ignore it?

  Read the article

• Windows 2003 Server R2SP2 throws even ID 2269 after installing Excel WebPart in MOSS3

  - by Phil

  We recently added an Excel workbook webpart (read only excel file - no editing) on our Sharepoint 2007 server. Once we did that, approximately 3-4 times an hour event ID 2269 is shown in the Application Log and a few minutes after that, an event id 1002 is displayed in the system long and the Sharepoint Offfce Servers Application pool shuts down. We've already check the "Bypass traverse checking and DCOM settings) per the MS KB and I have opened a ticket with MS Support. Problem is that MS Suppoert (sharepoint) thinks it is an IIS problem and the IIS people think it is a Sharepoint issue. Anyone else seen this problem? If we remove the Excel webpart, everything goes back to normal. The App Pools, SP and SP Central Admin sites are all using the same domain service account. Thanks in advance, Phil

  Read the article

• Major Issue with Asus M4A78T-E Bios

  - by user114721

  I am having major issues with my bios and I have tried three different forums in hopes that there is someone out there that can help me.... The issue is that every single time I turn off my computer, when I turn it back on the bios resets and tries to boot from a floppy drive....first problem is I dont have a floppy drive and secondly it does not read my HDD.... I tried everything to fix this...I tried replacing the cmos battery, I tried replacing the sata cable, and I tried a different sata port....none of these things seem to be working. Now the messed up part about all of this is that i am on my computer right now....If I take the battery out and put it back in and setup the bios again manually I am able to get into my computer...but this is NOT normal... Why is my bios resetting constantly when I power down my computer? Please assist me I need my computer for business

  Read the article

• Routing only some local IPs through VPN on dd-wrt

  - by bo-inge-ostberg

  Much similar to this entry: http://serverfault.com/questions/94283/using-dd-wrt-to-connect-to-vpn-and-forward-all-traffic-of-certain-devices-through , I have set up my router with dd-wrt + OpenVPN to connect to a VPN. This works fine, and all traffic from behind the router goes through the VPN. How do I route(?) traffic in the router so that only certain IPs from the LAN will go through the VPN, while the others take the "normal" route? Is it also possible to allow traffic from certain local IPs to go ONLY through the VPN, making it impossible for them to use the regular internet connection if the VPN is down? I know this question was answered in the post I linked to, but that just doesn't seem to work for me. The routing table and rules change, but traffic still just goes through the VPN.

  Read the article

• Apache service hung and incoming requests not accepted

  - by Gnanam

  Hi, My production server is running Apache v2.2.4 with mod_mono v1.2.4 on CentOS release 5.2 (Final). Suddenly, Apache service hung during normal usage time (approx. 1 pm EDT). Traffic is not too high at this time. This is the first time we're noticing this kind of behaviour in our server. I noticed from access log that even subsequent requests are also not received, even though there were incoming requests. I then manually tried to invoke my application call from web browser, it never returned successfully but it was still loading. I found no unusual behaviour/activity in: 1) Apache access_log and error_log 2) No kernel level errors found in /var/log/messages I've no other option but ended up restarting Apache service. Any idea on what would cause Apache to hang and thereby not allowing subsequent incoming requests? How do I debug/diagnose when this happens next time? Experts advice/recommendation on this are highly appreciated.

  Read the article

• 421 Concurrent Connections - Ratelimit from helpdesk to rackspace server

  - by g18c

  We have Kayako helpdesk running on our WHM Linux server. When e-mails come in from customers, notifications are sent out by Kayako to a number of staff whose mailboxes are hosted on Rackspace mail servers. I noticed a large queue in the Exim queued message viewer of WHM - when looking in Exim logs I can see many lines 2012-10-13 20:06:56 1TN72s-0007Cw-1l SMTP error from remote mail server after initial connection: host mx2.emailsrvr.com [173.203.2.32]: 421 Too many concurrent connections from this client. One client email results in about 5 emails to rackspace servers, perhaps 60 emails per 1 hour on average - not a huge amount but enough to cause messages to be rejected when sent in short bursts. In this case ideally if we can limit the connections sent to the rackspace server we can comply with their limit. For our requirements if we send 1 email every10 seconds or so, this would be OK. Messages to all other servers should go through a normal rates, only mx1.emailsrvr.com and mx2.emailsrvr.com should have this connection limit policy applied. Is this possible?

  Read the article

• Apache server in raspberry PI not visible from outside( public IP)

  - by Kronos

  I have made a fresh install of Arch Linux ARM into a Raspberry PI and I mounted there a LAMP, all fresh. I have another Arch(x86) in my laptop with Apache also there, and as far as I know, two web servers cannot run in the same network segment so, the problem is as follows. I my laptop, having Apache running, if I enter via the public ip of my network everything turns ok and I can see my website but, (obviously turning this server down) if I enter from the public IP with the Apache running in the raspberry pi( yes, only that Apache running) i cannot see my website in there. Also, if I access via local network it is a normal success, I can see my website. So, I can enter my raspberry website only via local but in my other web server i can enter it via local and public. I have the same conf files in both of them so what is the difference? I was planning in making the rpi as a development server. Thanks in advance

  Read the article

• Powershell overruling Perl binmode?

  - by hippietrail

  I have a Perl script which creates a binary file while scanning a very large text file. It outputs to STDOUT which I redirect in the commandline to a file. To optimize it I'm making changes then seeing how low it takes to run. On Linux for this I use the "time" command. On Windows the best way to time a program seemed to be to PowerShell's "measure-command". This seemed to work fine but I noticed the generated files were larger. On examination I found that the files generated from within PowerShell begin with a BOM and contain CRLF pairs! My Perl script has a "binmode STDOUT" directive and does work correctly in a normal dosbox. Is this a bug or misfeature in PowerShell or measure-command? Has it affected others creating binary files by means other than Perl? Googling hasn't turned anything up so far. I'm using Perl 5.12, PowerShell v1.0 and Windows XP.

  Read the article

• Set up router to vpn into proxy server

  - by NKimber

  I have a small network with a single LinkSys router connected to broadband in US via Comcast. I have a VPN proxy server account that I can use with a standard Windows connection, allowing me to have a geographic IP fingerprint in Europe, this is useful for a number of purposes. I want to setup a 2nd router that automatically connects via VPN to this proxy service, so any hardware that is connected to router 2 looks as though it is originating network requests in Europe, and any hardware connected to my main router has normal Comcast traffic (all requests are originating from USA). My 2nd router is a LinkSys WRT54G2, I'm having trouble getting this configured. Question, is what I'm trying to do even feasible? Should the WRT54G2 be able to do this with native functionality? Would flashing it with DD-WRT allow me to achieve my objectives? Any help/suggestions much appreciated. Neil

  Read the article

• Policy Routing with Openvpn?

  - by sadawd

  Dear Everyone I am currently using openvpn for normal browsing. However, I have the following services running: a bit torrent client, a web server, IRC and a git server which I would really want it to not be using my vpn connection (and use my original connection instead). Is there a way to do this? I looked up policy routing and I can't really find any tutorial on how to do this on linux (I am on ubuntu). I don't want the solution to be incredibly complicated - I am pretty new to networking in ubuntu and I only want a very simple solution to this problem. Can someone help me out?

  Read the article

• Lighttpd as a proxy to a https host

  - by Homer J. Simpson

  Hi, I am trying to set up a lighttpd as proxy from one server to another (which is running Apache/SSL), having trouble with the https part.. I want to be able to capture https requests and let the Apache server handle it, trying this: $SERVER["socket"] == ":443" { $HTTP["host"] == "www.mydomain.com" { proxy.server = ( "" => ( ( "host" => "123.123.123.123", # the Apache "port" => 443))) } } Normal port 80 requests are working fine.. What am I doing wrong ? Edit: Additionaly, error.log doesnt show anything.. Requests to https://www.mydomain.com are not finishing.

  Read the article

• zsh right-justify in ps1

  - by Nate

  I'd like a multi-line zsh prompt with a right alined part, that will look something like this: 2.nate@host:/current/dir 16:00 -> I know about RPROMPT in zsh, but that has a right-aligned prompt opposite your normal prompt, which is on the same line of text as your typing. Is there a way to have a right-aligned portion to the first line of a multi-line command prompt? I'm looking for either a directive in the PS1 variable that says 'right align now' or a variable that is to PS1 what RPROMPT is to PROMPT. Thanks!

  Read the article

• Double root folder vs single root folder

  - by Tomas

  On my Linux box, in bash, I have access to a "double root" folder denoted by two forward slashes: tomas:~ $ cd / tomas:/ $ ls bin/ cdrom@ ... tomas:/ $ cd // tomas:// $ ls bin/ cdrom@ ... The content of the folder and its subfolder is identical to the "normal" single slash root. The double slash does not go away when I access its subfolders. The annomaly does not repeat itself with three or more slashes; these are simple synonyms for the root: tomas:// $ cd home/tomas tomas://home/tomas $ cd /// tomas:/ $ cd //// tomas:/ $ What kindof place is it? Is it a bug? Can anyone explain the annomaly?

  Read the article

• vista winsxs folder eats disk space

  - by Simpzon

  My machine has been running Vista Ultimate 64-Bit for about two years now. ServicePacks SP1 and SP2 are installed, too. The system partition has a size of 55 GB, which should be quite comfortable under normal circumstances, but about 40GB (no typo) are used by the Windows-Folder, especially the subfolder winsxs, which takes about 35 GB. I have already uninstalled as many programs as possible and did run compcln.exe, to reduce it, but this only gained 2-3 GB. What can I do to clean up without risking system stability? I'm a software developer and this is my daily work environment, which means - I can't risk to get strange side-effects from blindly deleting stuff. - You can maybe deduce some typical usage patterns from this information. Any suggestions?

  Read the article

• Use an unsigned driver in Windows 7 x64

  - by rjmunro

  I'm trying to use the RBC9 SpaceNavigator TEST x64 build drivers for my SpaceNavigator 3d joystick so that it can work as a normal joystick in games like Quake. Unfortunately, I get the error "This version of windows requires all drivers to have a valid digital signature" and in the "Device status" in device manager, I get "Windows cannot verify the digital signature for the drivers required for this device. A recent hardware or software change might have installed a file that is signed incorrectly or damaged, or that might be malicious software from an unknown source. (Code 52)". Is there a way to work around this issue?

  Read the article

• Combine Multiple Audio Files into a single higher-quality audio File

  - by namenlos

  BACKGROUND My team gave a demo to a large audience - we recorded the audio of the demo in multiple locations in the room (3) the audio was recorded using cheap laptop microphones I was not involved in the recording of the audio or the demo Both audio files suck in some form the first one is of a recording near the speaker - which clearly gets his voice but the the audience is audience is muffled - also this one is slightly noisy The second recording was done in the middle of the audience - it gets the audience questions clearly but actually gets the speaker rather sometimes well and sometimes poorly (not all the speakers spoke loudly enough to be heard) MY QUESTION Is there any techinque or software which can be used to merge these audio files in such a way that the best qualities of each are preserved. I am NOT asking now to simply merge them together in one track - I've already done that in Audacity and it is certainly better - what I am looking for could be considered closer to how HDR images are created - multiple exposures combined into an enhanced new version which is not simply an average of the inputs. NOTE Am not an "Audio" guy - just a normal user

  Read the article

• Move MySQL database while instance is online

  - by Mike Scott

  I have a MySQL instance containing a number of databases, one of which is an archive database (although using the INNODB rather than ARCHIVE storage engine) that is not queried or written to in normal operation. The data filesystem is filling up and I'd like to move the archive database's data directory to a different filesystem (and then symlink it back, obviously). If there are no SQL statements attempting to query or update the data during the move, can I safely do this while the MySQL instance and the other databases stay online and in use? I plan to rsync the database directory to the new filesystem, then rename the old one on the original filesystem to something different and create the new symlink. lsof reports that MySQL does have the .ibd files open, so presumably it would have to reopen them.

  Read the article

• How to query Oracle from SQL Server ?

  - by Albert Widjaja

  Hi Everyone, I'm having difficulties in creating a connection from my SQL Server 2008 Enterprise SP2 x64 into the Oracle database 10g even though I have already install the Oracle Client 11g R2 ? I've followed this article from steps URL: http://www.ideaexcursion.com/2009/01/05/connecting-to-oracle-from-sql-server/ plus added: TNS_ADMIN into the Server variables which point into: C:\Oracle\product\11.2.0\client_1\network\admin what is working now: TNSNAMES.ORA has been copied successfully from the other Developer wworkstation i can TNSPING into the DB instance i can connect to the database using SQLplus and perform any SQL commands i can create the DSN ONLY when using "[b]C:\Windows\SysWOW64\odbcad32.exe[/b]" the normal odbcad32 doesn't show my DSN that I have just created ? the DSN created from the above works fine from the test connection. my goal: To be able to select the Oracle connection in the Linked server object but still no effect after I restart the server. (Windows Server 2008 Enterprise 64 bit SP2). Any idea please in resolving this problem would be greatly appreciated. Thanks.

  Read the article

< Previous Page | 219 220 221 222 223 224 225 226 227 228 229 230  | Next Page >