Search Results

Search found 11421 results on 457 pages for 'forms authentication'.

Page 226/457 | < Previous Page | 222 223 224 225 226 227 228 229 230 231 232 233  | Next Page >

• Ipsec config problem // openswan

  - by user90696

  I try to configure Ipsec on server with openswan as client. But receive error - possible, it's auth error. What I wrote wrong in config ? Thank you for answers. #1: STATE_MAIN_I2: sent MI2, expecting MR2 003 "f-net" #1: received Vendor ID payload [Cisco-Unity] 003 "f-net" #1: received Vendor ID payload [Dead Peer Detection] 003 "f-net" #1: ignoring unknown Vendor ID payload [ca917959574c7d5aed4222a9df367018] 003 "f-net" #1: received Vendor ID payload [XAUTH] 108 "f-net" #1: STATE_MAIN_I3: sent MI3, expecting MR3 003 "f-net" #1: discarding duplicate packet; already STATE_MAIN_I3 010 "f-net" #1: STATE_MAIN_I3: retransmission; will wait 20s for response 003 "f-net" #1: discarding duplicate packet; already STATE_MAIN_I3 003 "f-net" #1: discarding duplicate packet; already STATE_MAIN_I3 003 "f-net" #1: discarding duplicate packet; already STATE_MAIN_I3 010 "f-net" #1: STATE_MAIN_I3: retransmission; will wait 40s for response 031 "f-net" #1: max number of retransmissions (2) reached STATE_MAIN_I3. Possible authentication failure: no acceptable response to our first encrypted message 000 "f-net" #1: starting keying attempt 2 of at most 3, but releasing whack other side - Cisco ASA. parameters for my connection on our Linux server : VPN Gateway 8.*.*.* (Cisco ) Phase 1 Exchange Type Main Mode Identification Type IP Address Local ID 4.*.*.* (our Linux server IP) Remote ID 8.*.*.* (VPN server IP) Authentication PSK Pre Shared Key Diffie-Hellman Key Group DH 5 (1536 bit) or DH 2 (1024 bit) Encryption Algorithm AES 256 HMAC Function SHA-1 Lifetime 86.400 seconds / no volume limit Phase 2 Security Protocol ESP Connection Mode Tunnel Encryption Algorithm AES 256 HMAC Function SHA-1 Lifetime 3600 seconds / 4.608.000 kilobytes DPD / IKE Keepalive 15 seconds PFS off Remote Network 192.168.100.0/24 Local Network 1 10.0.0.0/16 ............... Local Network 5 current openswan config : # config setup klipsdebug=all plutodebug="control parsing" protostack=netkey nat_traversal=no virtual_private=%v4:10.0.0.0/8,%v4:192.168.0.0/16,%v4:172.16.0.0/12 oe=off nhelpers=0 conn f-net type=tunnel keyexchange=ike authby=secret auth=esp esp=aes256-sha1 keyingtries=3 pfs=no aggrmode=no keylife=3600s ike=aes256-sha1-modp1024 # left=4.*.*.* leftsubnet=10.0.0.0/16 leftid=4.*.*.* leftnexthop=%defaultroute right=8.*.*.* rightsubnet=192.168.100.0/24 rightid=8.*.*.* rightnexthop=%defaultroute auto=add

  Read the article

• Cisco SR520w FE - WAN Port Stops Working

  - by Mike Hanley

  I have setup a Cisco SR520W and everything appears to be working. After about 1-2 days, it looks like the WAN port stops forwarding traffic to the Internet gateway IP of the device. If I unplug and then plug in the network cable connecting the WAN port of the SR520W to my Comcast Cable Modem, traffic startings flowing again. Also, if I restart the SR520W, the traffic will flow again. Any ideas? Here is the running config: Current configuration : 10559 bytes ! version 12.4 no service pad no service timestamps debug uptime service timestamps log datetime msec no service password-encryption ! hostname hostname.mydomain.com ! boot-start-marker boot-end-marker ! logging message-counter syslog no logging rate-limit enable secret 5 <removed> ! aaa new-model ! ! aaa authentication login default local aaa authorization exec default local ! ! aaa session-id common clock timezone PST -8 clock summer-time PDT recurring ! crypto pki trustpoint TP-self-signed-334750407 enrollment selfsigned subject-name cn=IOS-Self-Signed-Certificate-334750407 revocation-check none rsakeypair TP-self-signed-334750407 ! ! crypto pki certificate chain TP-self-signed-334750407 certificate self-signed 01 <removed> quit dot11 syslog ! dot11 ssid <removed> vlan 75 authentication open authentication key-management wpa guest-mode wpa-psk ascii 0 <removed> ! ip source-route ! ! ip dhcp excluded-address 172.16.0.1 172.16.0.10 ! ip dhcp pool inside import all network 172.16.0.0 255.240.0.0 default-router 172.16.0.1 dns-server 10.0.0.15 10.0.0.12 domain-name mydomain.com ! ! ip cef ip domain name mydomain.com ip name-server 68.87.76.178 ip name-server 66.240.48.9 ip port-map user-ezvpn-remote port udp 10000 ip ips notify SDEE ip ips name sdm_ips_rule ! ip ips signature-category category all retired true category ios_ips basic retired false ! ip inspect log drop-pkt no ipv6 cef ! multilink bundle-name authenticated parameter-map type inspect z1-z2-pmap audit-trail on password encryption aes ! ! username admin privilege 15 secret 5 <removed> ! crypto key pubkey-chain rsa named-key realm-cisco.pub key-string <removed> quit ! ! ! ! ! ! crypto ipsec client ezvpn EZVPN_REMOTE_CONNECTION_1 connect auto group EZVPN_GROUP_1 key <removed> mode client peer 64.1.208.90 virtual-interface 1 username admin password <removed> xauth userid mode local ! ! archive log config logging enable logging size 600 hidekeys ! ! ! class-map type inspect match-any SDM_AH match access-group name SDM_AH class-map type inspect match-any SDM-Voice-permit match protocol sip class-map type inspect match-any SDM_ESP match access-group name SDM_ESP class-map type inspect match-any SDM_EASY_VPN_REMOTE_TRAFFIC match protocol isakmp match protocol ipsec-msft match class-map SDM_AH match class-map SDM_ESP match protocol user-ezvpn-remote class-map type inspect match-all SDM_EASY_VPN_REMOTE_PT match class-map SDM_EASY_VPN_REMOTE_TRAFFIC match access-group 101 class-map type inspect match-any Easy_VPN_Remote_VT match access-group 102 class-map type inspect match-any sdm-cls-icmp-access match protocol icmp match protocol tcp match protocol udp class-map type inspect match-any sdm-cls-insp-traffic match protocol cuseeme match protocol dns match protocol ftp match protocol h323 match protocol https match protocol icmp match protocol imap match protocol pop3 match protocol netshow match protocol shell match protocol realmedia match protocol rtsp match protocol smtp extended match protocol sql-net match protocol streamworks match protocol tftp match protocol vdolive match protocol tcp match protocol udp class-map type inspect match-any L4-inspect-class match protocol icmp class-map type inspect match-all sdm-invalid-src match access-group 100 class-map type inspect match-all dhcp_out_self match access-group name dhcp-resp-permit class-map type inspect match-all dhcp_self_out match access-group name dhcp-req-permit class-map type inspect match-all sdm-protocol-http match protocol http ! ! policy-map type inspect sdm-permit-icmpreply class type inspect dhcp_self_out pass class type inspect sdm-cls-icmp-access inspect class class-default pass policy-map type inspect sdm-permit_VT class type inspect Easy_VPN_Remote_VT pass class class-default drop policy-map type inspect sdm-inspect class type inspect SDM-Voice-permit pass class type inspect sdm-cls-insp-traffic inspect class type inspect sdm-invalid-src drop log class type inspect sdm-protocol-http inspect z1-z2-pmap class class-default pass policy-map type inspect sdm-inspect-voip-in class type inspect SDM-Voice-permit pass class class-default drop policy-map type inspect sdm-permit class type inspect SDM_EASY_VPN_REMOTE_PT pass class type inspect dhcp_out_self pass class class-default drop ! zone security ezvpn-zone zone security out-zone zone security in-zone zone-pair security sdm-zp-in-ezvpn1 source in-zone destination ezvpn-zone service-policy type inspect sdm-permit_VT zone-pair security sdm-zp-out-ezpn1 source out-zone destination ezvpn-zone service-policy type inspect sdm-permit_VT zone-pair security sdm-zp-ezvpn-out1 source ezvpn-zone destination out-zone service-policy type inspect sdm-permit_VT zone-pair security sdm-zp-self-out source self destination out-zone service-policy type inspect sdm-permit-icmpreply zone-pair security sdm-zp-out-in source out-zone destination in-zone service-policy type inspect sdm-inspect-voip-in zone-pair security sdm-zp-ezvpn-in1 source ezvpn-zone destination in-zone service-policy type inspect sdm-permit_VT zone-pair security sdm-zp-out-self source out-zone destination self service-policy type inspect sdm-permit zone-pair security sdm-zp-in-out source in-zone destination out-zone service-policy type inspect sdm-inspect ! bridge irb ! ! interface FastEthernet0 switchport access vlan 75 ! interface FastEthernet1 switchport access vlan 75 ! interface FastEthernet2 switchport access vlan 75 ! interface FastEthernet3 switchport access vlan 75 ! interface FastEthernet4 description $FW_OUTSIDE$ ip address 75.149.48.76 255.255.255.240 ip nat outside ip ips sdm_ips_rule out ip virtual-reassembly zone-member security out-zone duplex auto speed auto crypto ipsec client ezvpn EZVPN_REMOTE_CONNECTION_1 ! interface Virtual-Template1 type tunnel no ip address ip virtual-reassembly zone-member security ezvpn-zone tunnel mode ipsec ipv4 ! interface Dot11Radio0 no ip address ! encryption vlan 75 mode ciphers aes-ccm ! ssid <removed> ! speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0 station-role root ! interface Dot11Radio0.75 encapsulation dot1Q 75 native ip virtual-reassembly bridge-group 75 bridge-group 75 subscriber-loop-control bridge-group 75 spanning-disabled bridge-group 75 block-unknown-source no bridge-group 75 source-learning no bridge-group 75 unicast-flooding ! interface Vlan1 no ip address ip virtual-reassembly bridge-group 1 ! interface Vlan75 no ip address ip virtual-reassembly bridge-group 75 bridge-group 75 spanning-disabled ! interface BVI1 no ip address ip nat inside ip virtual-reassembly ! interface BVI75 description $FW_INSIDE$ ip address 172.16.0.1 255.240.0.0 ip nat inside ip ips sdm_ips_rule in ip virtual-reassembly zone-member security in-zone crypto ipsec client ezvpn EZVPN_REMOTE_CONNECTION_1 inside ! ip forward-protocol nd ip route 0.0.0.0 0.0.0.0 75.149.48.78 2 ! ip http server ip http authentication local ip http secure-server ip http timeout-policy idle 60 life 86400 requests 10000 ip nat inside source list 1 interface FastEthernet4 overload ! ip access-list extended SDM_AH remark SDM_ACL Category=1 permit ahp any any ip access-list extended SDM_ESP remark SDM_ACL Category=1 permit esp any any ip access-list extended dhcp-req-permit remark SDM_ACL Category=1 permit udp any eq bootpc any eq bootps ip access-list extended dhcp-resp-permit remark SDM_ACL Category=1 permit udp any eq bootps any eq bootpc ! access-list 1 remark SDM_ACL Category=2 access-list 1 permit 172.16.0.0 0.15.255.255 access-list 100 remark SDM_ACL Category=128 access-list 100 permit ip host 255.255.255.255 any access-list 100 permit ip 127.0.0.0 0.255.255.255 any access-list 100 permit ip 75.149.48.64 0.0.0.15 any access-list 101 remark SDM_ACL Category=128 access-list 101 permit ip host 64.1.208.90 any access-list 102 remark SDM_ACL Category=1 access-list 102 permit ip any any ! ! ! ! snmp-server community <removed> RO ! control-plane ! bridge 1 protocol ieee bridge 1 route ip bridge 75 route ip banner login ^CSR520 Base Config - MFG 1.0 ^C ! line con 0 no modem enable line aux 0 line vty 0 4 transport input telnet ssh ! scheduler max-task-time 5000 end I also ran some diagnostics when the WAN port stopped working: 1. show interface fa4 FastEthernet4 is up, line protocol is up Hardware is PQUICC_FEC, address is 0026.99c5.b434 (bia 0026.99c5.b434) Description: $FW_OUTSIDE$ Internet address is 75.149.48.76/28 MTU 1500 bytes, BW 100000 Kbit/sec, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 100Mb/s, 100BaseTX/FX ARP type: ARPA, ARP Timeout 04:00:00 Last input 01:08:15, output 00:00:00, output hang never Last clearing of "show interface" counters never Input queue: 0/75/23/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 1000 bits/sec, 0 packets/sec 336446 packets input, 455403158 bytes Received 23 broadcasts, 0 runts, 0 giants, 37 throttles 41 input errors, 0 CRC, 0 frame, 0 overrun, 41 ignored 0 watchdog 0 input packets with dribble condition detected 172529 packets output, 23580132 bytes, 0 underruns 0 output errors, 0 collisions, 2 interface resets 0 unknown protocol drops 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier 0 output buffer failures, 0 output buffers swapped out 2. show ip route Gateway of last resort is 75.149.48.78 to network 0.0.0.0 C 192.168.75.0/24 is directly connected, BVI75 64.0.0.0/32 is subnetted, 1 subnets S 64.1.208.90 [1/0] via 75.149.48.78 S 192.168.10.0/24 is directly connected, BVI75 75.0.0.0/28 is subnetted, 1 subnets C 75.149.48.64 is directly connected, FastEthernet4 S* 0.0.0.0/0 [2/0] via 75.149.48.78 3. show ip arp Protocol Address Age (min) Hardware Addr Type Interface Internet 75.149.48.65 69 001e.2a39.7b08 ARPA FastEthernet4 Internet 75.149.48.76 - 0026.99c5.b434 ARPA FastEthernet4 Internet 75.149.48.78 93 0022.2d6c.ae36 ARPA FastEthernet4 Internet 192.168.75.1 - 0027.0d58.f5f0 ARPA BVI75 Internet 192.168.75.12 50 7c6d.62c7.8c0a ARPA BVI75 Internet 192.168.75.13 0 001b.6301.1227 ARPA BVI75 4. sh ip cef Prefix Next Hop Interface 0.0.0.0/0 75.149.48.78 FastEthernet4 0.0.0.0/8 drop 0.0.0.0/32 receive 64.1.208.90/32 75.149.48.78 FastEthernet4 75.149.48.64/28 attached FastEthernet4 75.149.48.64/32 receive FastEthernet4 75.149.48.65/32 attached FastEthernet4 75.149.48.76/32 receive FastEthernet4 75.149.48.78/32 attached FastEthernet4 75.149.48.79/32 receive FastEthernet4 127.0.0.0/8 drop 192.168.10.0/24 attached BVI75 192.168.75.0/24 attached BVI75 192.168.75.0/32 receive BVI75 192.168.75.1/32 receive BVI75 192.168.75.12/32 attached BVI75 192.168.75.13/32 attached BVI75 192.168.75.255/32 receive BVI75 224.0.0.0/4 drop 224.0.0.0/24 receive 240.0.0.0/4 drop 255.255.255.255/32 receive Thanks in advance, -Mike

  Read the article

• ubuntu 9.10 cups server cupsd.conf

  - by aaron

  i have a cups server running on ubuntu 9.10 on my home network. right now i can access it at 192.168.1.101:631, but when i try to access it at myservername.local:631 i get a 400 Bad Request. here's the relevant section from my current cupsd.conf: ServerName 192.168.1.101 # Only listen for connections from the local machine. Listen localhost:631 Listen /var/run/cups/cups.sock # any of the below 'Listen' directives all yield the same result Listen 192.168.1.101:631 #Listen *:631 #Listen myservername.local:631 # Show shared printers on the local network. Browsing On BrowseOrder allow,deny BrowseAllow all BrowseLocalProtocols CUPS dnssd BrowseAddress 192.168.1.255 # Default authentication type, when authentication is required... DefaultAuthType Basic # Restrict access to the server... <Location /> Order deny,allow Deny from All Allow from 127.0.0.1 Allow from 192.168.1.* </Location> # Restrict access to the admin pages... <Location /admin> Order deny,allow Deny from All #Allow from 127.0.0.1 #Allow from 192.168.1.* </Location> # Restrict access to configuration files... <Location /admin/conf> AuthType Default Require user @SYSTEM Order deny,allow Deny from All #Allow from 127.0.0.1 #Allow from 192.168.1.* </Location> i get the following in /var/log/cups/error_log: E [03/Jan/2010:18:33:41 -0600] Request from "192.168.1.100" using invalid Host: field "myservername.local:631" what do i need to do to be able to access the cups server at both 192.168.1.101:631 and myservername.local:631?

  Read the article

• scp error: "Permission denied (publickey). lost connection"

  - by Winston C. Yang

  I tried to scp an svn dump to savannah, but I got the following error at the end. Permission denied (publickey). lost connection The scp command and verbose output are below. Any ideas? [wcyang@be2-wireless-pittnet-60-37 ~]$ scp -v diffcolor-dump.bz2 [email protected]:/srv/download/diffcolor/ Executing: program /usr/bin/ssh host dl.sv.gnu.org, user wcyang, command scp -v -t /srv/download/diffcolor/ OpenSSH_5.2p1, OpenSSL 0.9.7l 28 Sep 2006 debug1: Reading configuration data /etc/ssh_config debug1: Connecting to dl.sv.gnu.org [140.186.70.73] port 22. debug1: Connection established. debug1: identity file /Users/wcyang/.ssh/identity type -1 debug1: identity file /Users/wcyang/.ssh/id_rsa type 1 debug1: identity file /Users/wcyang/.ssh/id_dsa type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.1p1 Debian-5 debug1: match: OpenSSH_5.1p1 Debian-5 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.2 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-ctr hmac-md5 none debug1: kex: client->server aes128-ctr hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Host 'dl.sv.gnu.org' is known and matches the RSA host key. debug1: Found key in /Users/wcyang/.ssh/known_hosts:1 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey debug1: Next authentication method: publickey debug1: Trying private key: /Users/wcyang/.ssh/identity debug1: Offering public key: /Users/wcyang/.ssh/id_rsa debug1: Authentications that can continue: publickey debug1: Trying private key: /Users/wcyang/.ssh/id_dsa debug1: No more authentication methods to try. Permission denied (publickey). lost connection

  Read the article

• SqlCmd : Login timeout expired from localhost

  - by mschr

  I've setup the instance SQLEXPRESS via SQL Server 2008 R2 installation, added a security login with all server roles, one called 'sqluser'. The server authentication is SQL Server and Windows Authentication mode. However, when i specify the -S property, login fails. There is no firewall enabled and SQL server even accepts connections from remote hosts. C:\Users\user>sqlcmd -U sqluser -P qwerty -Q "Select * FROM testdb.dbo.testtable" Output: integer ------- 1 2 3 4 (4 rows affected) However when specifying 'localhost' the query fails... Question is Why? C:\Users\user>sqlcmd -S localhost/sqlexpress -U cpt -P 1234 -Q "Select * FROM cpt.dbo.testme" Output: HResult 0x43, Level 16, State 1 Named Pipes Provider: Could not open a connection to SQL Server [67]. Sqlcmd: Error: Microsoft SQL Server Native Client 10.0 : A network-related or in stance-specific error ..... Sqlcmd: Error: Microsoft SQL Server Native Client 10.0 : Login timeout expired. Changing 'localhost' with '%COMPUTERNAME' is same result if someone would be wondering. The server is running as a LocalSystem instance.

  Read the article

• Excel cannot access the file with IIS7&Windows Serer 2008 R2(64bit)

  - by user838204

  I have a web project(.Net4) that needs to access Excel file, but it ends up with the following error message: Error occured during file generation.Microsoft Excel cannot access the file 'D:\xx\xx\abc.xls'. There are several possible reasons: • The file name or path does not exist. (Actually it's there) • The file is being used by another program.(It cant happen) • The workbook you are trying to save has the same name as a currently open workbook. In IIS7, I use DefaultAppPool with the Identity "myservice" who's under the Group of Administrators. In the Authentication Page of my website under IIS, Anonymous Authentication was enabled and set to "Application pool identity" and ASP.NET Impersonation was disabled. After searching the solution for hours, I found the following but NONE of them work Create folder in C:\Windows\SysWOW64\config\systemprofile\Desktop. Plz refer:this Grant rights of "myservice" in Component Services. Plz refer:this One thing strange, there is nothing in the Group of IIS_IUSRS. Is that normal? Cause I remember at least two users (DefaultAppPool & Classic .Net AppPool). Plz tell me how to fix the access problem. I assume that's permission problem of IIS but I cant solve it. Thank you.

  Read the article

• Why can't I ssh into my server using my private key?

  - by user61342

  I just setup my new server as I used to, and this time I can't login using my private key. The server is ubuntu 11.04. And I have setup following ssh key directories. root@myserv: ls -la drwx------ 2 root root 4096 Sep 23 03:40 .ssh And in .ssh directory, I have done chmod 640 authorized_keys Here is the ssh connection tracebacks: OpenSSH_5.9p1, OpenSSL 0.9.8r 8 Feb 2011 debug1: Reading configuration data /etc/ssh_config debug1: /etc/ssh_config line 20: Applying options for * debug1: Connecting to [my.server.ip] [[my.server.ip]] port 22. debug1: Connection established. debug1: identity file /Users/john/.ssh/id_rsa type -1 debug1: identity file /Users/john/.ssh/id_rsa-cert type -1 debug1: identity file /Users/john/.ssh/id_dsa type 1 debug1: identity file /Users/john/.ssh/id_dsa-cert type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.8p1 Debian-1ubuntu3 debug1: match: OpenSSH_5.8p1 Debian-1ubuntu3 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.9 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-ctr hmac-md5 none debug1: kex: client->server aes128-ctr hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Server host key: RSA ef:b8:8f:b4:fc:a0:57:7d:ce:50:36:17:37:fa:f7:ec debug1: Host '[my.server.ip]' is known and matches the RSA host key. debug1: Found key in /Users/john/.ssh/known_hosts:2 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: Roaming not allowed by server debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey,password debug1: Next authentication method: publickey debug1: Trying private key: /Users/john/.ssh/id_rsa debug1: Offering RSA public key: /Users/john/.ssh/id_dsa debug1: Authentications that can continue: publickey,password debug1: Next authentication method: password root@[my.server.ip]'s password: Update: I have found the reason but I can't explain it yet. It is caused by uploading the key using rsync -chavz instead of scp, after I used scp to upload my key, the issue is gone. Can someone explain it? Later, I tried rsync -chv, still not working

  Read the article

• LDAP change user pass on client

  - by Sean

  I am trying to allow ldap users to change their password on client machines. I have tried pam every which way I can think of /etc/ldap.conf & /etc/pam_ldap.conf, as well. At this point I'm stuck. Client: Ubuntu 11.04 Server: Debian 6.0 The current output is this: sobrien4@T-E700F-1:~$ passwd passwd: Authentication service cannot retrieve authentication info passwd: password unchanged /var/log/auth.log gives this during the command: May 9 10:49:06 T-E700F-1 passwd[18515]: pam_unix(passwd:chauthtok): user "sobrien4" does not exist in /etc/passwd May 9 10:49:06 T-E700F-1 passwd[18515]: pam_ldap: ldap_simple_bind Can't contact LDAP server May 9 10:49:06 T-E700F-1 passwd[18515]: pam_ldap: reconnecting to LDAP server... May 9 10:49:06 T-E700F-1 passwd[18515]: pam_ldap: ldap_simple_bind Can't contact LDAP server getent passwd |grep sobrien4 (note keeping short since testing with that account, however it outputs all ldap users): sobrien4:Ffm1oHzwnLz0U:10000:12001:Sean O'Brien:/home/sobrien4:/bin/bash getent group shows all ldap groups. /etc/pam.d/common-password (Note this is just the most current, I have tried a lot of different options): password required pam_cracklib.so retry=3 minlen=8 difok=3 password [success=1 default=ignore] pam_unix.so use_authtok md5 password required pam_ldap.so use_authtok password required pam_permit.so Popped open wireshark as well, the server & client are talking. I have the password changing working on the server. I.E. the server that runs slapd, I can log in with the ldap user and change the passwords. I tried copying the working configs from the server initially and no dice. I also tried cloning it, and just changing ip & host, and no go. My guess is that the client is not authorized by ip or hostname to change a pass. Pertaining to the slapd conf, I saw this in a guide and tried it: access to attrs=loginShell,gecos by dn="cn=admin,dc=cengineering,dc=etb" write by self write by * read access to * by dn="cn=admin,dc=cengineering,dc=etb" write by self write by * read So ldap seems to be working okay, just can't change the password.

  Read the article

• Issue configuring Oracle database for SSL

  - by Santhosha Kaldambe

  Hello, I want to setup Oracle for SSL communication. I am not using SSL authentication for database user. As first requirement, generated self signed certificate using OpenSSL and added certificate to wallet. The wallet location is specified in server configuration. Created listener and it is starting however it does not provide any service. The default listener (non SSL) is working fine. When I execute LSNRCTL.EXE status SSLLISTENER it gives below output. STATUS of the LISTENER Alias SSLLISTENER Version TNSLSNR for 32-bit Windows: Version 11.1.0.6.0 - Production Start Date 14-NOV-2009 01:47:08 Uptime 16 days 22 hr. 14 min. 3 sec Trace Level off Security ON: Local OS Authentication SNMP OFF Listener Parameter File C:\app\Administrator\product\11.1.0\db_1\network\admin\listener.ora Listener Log File c:\app\administrator\diag\tnslsnr\\ssllistener\alert\log.xml Listening Endpoints Summary... (DESCRIPTION=(ADDRESS=(PROTOCOL=tcps)(HOST=)(PORT =2484))) The listener supports no services The command completed successfully Here is exact content of various files after configuration. 1) File Name: tnsnames.ora ORCL = (DESCRIPTION = (ADDRESS_LIST = (ADDRESS = (PROTOCOL = TCP)(HOST = )(PORT 1521)) ) (CONNECT_DATA = (SERVER = DEDICATED) (SERVICE_NAME = orcl) ) ) 2) File Name: sqlnet.ora SSL_VERSION = 0 NAMES.DIRECTORY_PATH= (TNSNAMES, EZCONNECT) sqlnet.authentication_services= (NONE) tcp.validnode_checking = no tcp.invited_nodes=(PS0803.oraebs.com,PS2948,PS5098) SSL_CLIENT_AUTHENTICATION = FALSE WALLET_LOCATION = (SOURCE = (METHOD = FILE) (METHOD_DATA = (DIRECTORY = C:\app\Administrator\admin\orcl\Server_Wallet) ) ) 3) File Name: listener.ora SSL_CLIENT_AUTHENTICATION = FALSE WALLET_LOCATION = (SOURCE = (METHOD = FILE) (METHOD_DATA = (DIRECTORY = C:\app\Administrator\admin\orcl\Server_Wallet) ) ) LISTENER = (DESCRIPTION_LIST = (DESCRIPTION = (ADDRESS = (PROTOCOL = IPC)(KEY = EXTPROC1521)) ) (DESCRIPTION = (ADDRESS = (PROTOCOL = TCP)(HOST = )(PORT 1521)) ) ) SSLLISTENER = (DESCRIPTION = (ADDRESS = (PROTOCOL = TCPS)(HOST = )(PORT = 2484)) ) Thanks Santhosh

  Read the article

• Cannot connect to my EC2 instance because of "Permission denied (publickey)"

  - by Burak

  In AWS console, I saw that my key pair was deleted. I created a new one with the same name. Then I tried to connect with ssh -v -i sohoKey.pem ec2-user@******.compute-1.amazonaws.com Here's the output: macs-MacBook-Air:~ mac$ ssh -v -i sohoKey.pem ec2-user@******.compute-1.amazonaws.com OpenSSH_5.6p1, OpenSSL 0.9.8r 8 Feb 2011 debug1: Reading configuration data /etc/ssh_config debug1: Applying options for * debug1: Connecting to ********.compute-1.amazonaws.com [*****] port 22. debug1: Connection established. debug1: identity file sohoKey.pem type -1 debug1: identity file sohoKey.pem-cert type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.3 debug1: match: OpenSSH_5.3 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.6 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-ctr hmac-md5 none debug1: kex: client->server aes128-ctr hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Host '*******.compute-1.amazonaws.com' is known and matches the RSA host key. debug1: Found key in /Users/mac/.ssh/known_hosts:3 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: Roaming not allowed by server debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey debug1: Next authentication method: publickey debug1: Offering RSA public key: sohoKey.pem debug1: Authentications that can continue: publickey debug1: Trying private key: sohoKey.pem debug1: read PEM private key done: type RSA debug1: Authentications that can continue: publickey debug1: No more authentication methods to try. Permission denied (publickey). Update: I detached my old EBS and attached to the new instance. Now, how can I mount it?

  Read the article

• Remote Desktop to Server 2008R2 fails from one particular Win7 client

  - by Jesse McGrew

  I have a VPS running Windows Web Server 2008 R2. I'm able to connect using Remote Desktop from my home PC (Windows 7), personal laptop (Windows 7), and work laptop (Windows XP). However, I cannot connect from my work PC (Windows 7). I receive the error "The logon attempt failed" in the RDP client, and the server event log shows "An account failed to log on" with this explanation: Subject: Security ID: NULL SID Account Name: - Account Domain: - Logon ID: 0x0 Logon Type: 3 Account For Which Logon Failed: Security ID: NULL SID Account Name: username Account Domain: hostname Failure Information: Failure Reason: Unknown user name or bad password. Status: 0xc000006d Sub Status: 0xc0000064 Process Information: Caller Process ID: 0x0 Caller Process Name: - Network Information: Workstation Name: JESSE-PC Source Network Address: - Source Port: - Detailed Authentication Information: Logon Process: NtLmSsp Authentication Package: NTLM Transited Services: - Package Name (NTLM only): - Key Length: 0 I can connect from the offending work PC if I start up Windows XP Mode and use the RDP client inside that. The server is part of a domain but my account is local, so I'm logging in using a username of the form hostname\username. None of the clients are part of a domain. The server uses a self-signed certificate, and connecting from home I get a warning about that, but connecting from work I just get the logon error.

  Read the article

• chmod -R 777 / on ubuntu - numerous problems

  - by ncatnow

  A client has accidentally given the entire filesystem full permissions on their ubuntu 10.04 box. chmod -R 777 httpdocs/cd / As you can see they attempted to cd to the root, and instead gave chmod a fun parameter to play with. First sign of the problem was inability to use 'su', giving an authentication error. sudo also complained of a missing setuid bit. This was fixed by logging in as root from the machine itself, and running chmod +s /usr/bin/sudo. I can now sudo su and do what I need to as root. su still gives an authentication failure. I followed the advice here: http://swiss.ubuntuforums.org/showthread.php?t=1180661&page=2 chmod 0755 / chmod 0755 /* chmod 1777 /tmp chmod 0750 /root chmod 0700 /lost+found I then tried to reset root password. I still cannot su to become root, or su root. The system seems to be running fine. Are there any suggestions for getting su to work once again? Where can I look for more problems?

  Read the article

• Apache2 Enabling Includes module causes svn access to quit working

  - by Matthew Talbert

  I have dav_svn installed to provide http access to my svn repos. The url is directly under root, eg mywebsite.com/svn/individual-repo. This setup has been working great for some time. Now, I need SSI (server-side includes) for a project, so I enabled this module with a2enmod include. Now, tortoisesvn can't access the repo; it always returns a 301 permanent redirect. Some playing with it reveals I can access it in a browser if I'm sure to include the trailing / but it still doesn't work in TortoiseSVN. I've looked at all of the faq's for this problem with TortoiseSVN and apache, and none of them seem to apply to my problem. Anyone have any insight into this problem? I'm running Ubuntu 9.10 with Apache 2.2.12. The only change I've made to my configuration is to enable the includes mod. Here's my dav_svn conf: <Location /svn> DAV svn SVNParentPath /home/matthew/svn AuthType Basic AuthName "Subversion repository" AuthUserFile /etc/subversion/passwd Require valid-user </Location> and here's the relevant part of my virtual host conf: <Location /svn> SetHandler None Order allow,deny Allow from all </Location> Edit: OK, I've discovered that the real conflict is between the include module and basic authentication. That is, if I disable the include module, browse to the subversion repo, enter my user/pass for the basic authentication, I can browse it just fine. It even continues to work after I re-enable the include module. However, if I browse with another browser where I'm not already authenticated, then it no longer works.

  Read the article

• PPTP Client setup, Fedora 17

  - by Suarez Romina

  I am trying to connect to hidemyass.com VPN services via PPTP, but I am having issues understanding why it isn't working, since I don't get a warning or fatal error and my IP remains the same. This is how i create the connection: [root@lasvegas-nv-datacenter ~]# pptpsetup --create TUNNELNAME --server 199.58.165.20 --username MYUSERNAME --password MYPASSWORD --encrypt --start And this is the output: Using interface ppp0 Connect: ppp0 <-- /dev/pts/1 CHAP authentication succeeded MPPE 128-bit stateless compression enabled local IP address 10.200.21.14 remote IP address 10.200.20.1 After that, I check the log and this is what i get: [root@lasvegas-nv-datacenter ~]# tail -f /var/log/messages Aug 24 11:25:33 lasvegas-nv-datacenter pptp[3892]: anon log[ctrlp_rep:pptp_ctrl.c:254]: Sent control packet type is 1 'Start-Control-Connection-Request' Aug 24 11:25:33 lasvegas-nv-datacenter pptp[3892]: anon log[ctrlp_disp:pptp_ctrl.c:754]: Received Start Control Connection Reply Aug 24 11:25:33 lasvegas-nv-datacenter pptp[3892]: anon log[ctrlp_disp:pptp_ctrl.c:788]: Client connection established. Aug 24 11:25:34 lasvegas-nv-datacenter pptp[3892]: anon log[ctrlp_rep:pptp_ctrl.c:254]: Sent control packet type is 7 'Outgoing-Call-Request' Aug 24 11:25:34 lasvegas-nv-datacenter pptp[3892]: anon log[ctrlp_disp:pptp_ctrl.c:873]: Received Outgoing Call Reply. Aug 24 11:25:34 lasvegas-nv-datacenter pptp[3892]: anon log[ctrlp_disp:pptp_ctrl.c:912]: Outgoing call established (call ID 0, peer's call ID 20096). Aug 24 11:25:38 lasvegas-nv-datacenter pppd[3884]: CHAP authentication succeeded Aug 24 11:25:38 lasvegas-nv-datacenter pppd[3884]: MPPE 128-bit stateless compression enabled Aug 24 11:25:38 lasvegas-nv-datacenter pppd[3884]: local IP address 10.200.21.14 Aug 24 11:25:38 lasvegas-nv-datacenter pppd[3884]: remote IP address 10.200.20.1 Can someone help me? Basically, i Ieed to connect to the VPN and have my IP changed after the connection. I read a lot of guides but still cannot understand why I don't get a connection.

  Read the article

• linked-server sql - access

  - by user22121

  Hi, I have a SQL server 2000 and an Access database mdb connected by Linked server on the other hand I have a program in c # that updates data in a SQL table (Users) based data base access. When running my program returns the following error message: OLE DB provider 'Microsoft.Jet.OLEDB.4.0' reported an error. Authentication failed. [OLE / DB provider returned message: Can not start the application. Missing information file of the working group or is opened exclusively by another user.] OLE DB error trace [OLE / DB Provider 'Microsoft.Jet.OLEDB.4.0' IDBInitialize:: Initialize returned 0x80040E4D: Authentication failed.] . Both the program, the sql server and database access are on a remote server. On the local server the problem was solved by running the following: "sp_addlinkedsrvlogin 'ActSC', 'false', NULL, 'admin', NULL". Try on the remote server the next, without result: "sp_addlinkedsrvlogin 'ActSC', true, null, 'user', 'pass'". On the remote server and from the "Query Analyzer" sql update statements are working correctly. Can you think of what may be the problem? Thanks!

  Read the article

• Cannot push to GitHub from Amazon EC2 Linux instance

  - by Eli

  Having the worst luck push files to a repo from EC2 to GitHub. I have my ssh key setup and added to Github. Here are the results of ssh -v [email protected] OpenSSH_5.3p1, OpenSSL 1.0.0g-fips 18 Jan 2012 debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for * debug1: Connecting to github.com [207.97.227.239] port 22. debug1: Connection established. debug1: permanently_set_uid: 0/0 debug1: identity file /root/.ssh/identity type -1 debug1: identity file /root/.ssh/id_rsa type 1 debug1: identity file /root/.ssh/id_dsa type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.1p1 Debian-5github2 debug1: match: OpenSSH_5.1p1 Debian-5github2 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.3 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-ctr hmac-md5 none debug1: kex: client->server aes128-ctr hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Host 'github.com' is known and matches the RSA host key. debug1: Found key in /root/.ssh/known_hosts:1 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey debug1: Next authentication method: publickey debug1: Trying private key: /root/.ssh/identity debug1: Offering public key: /root/.ssh/id_rsa debug1: Remote: Forced command: gerve eliperelman 81:5f:8a:b2:42:6d:4e:8c:2d:ba:9a:8a:2b:9e:1a:90 debug1: Remote: Port forwarding disabled. debug1: Remote: X11 forwarding disabled. debug1: Remote: Agent forwarding disabled. debug1: Remote: Pty allocation disabled. debug1: Server accepts key: pkalg ssh-rsa blen 277 debug1: Trying private key: /root/.ssh/id_dsa debug1: No more authentication methods to try. Permission denied (publickey).

  Read the article

• IIS 7 rewriting subdomain to point at a specific port

  - by Tommy Jakobsen

  Having installed Team Foundation Server 2010 on Windows Server 2008, I need an easy URL for our developers to access their repositories. The default URL for the TFS repositories is http://localhost:8080/tfs Now I want the subdomain domain tfs.server.domain.com to point at http://localhost:8080/tfs. And when you access tfs.server.domain.com/repos_name it should redirect to http://localhost:8080/tfs/repos_name. How can I do this in IIS7? I already tried using the following rule, but it does not work. I get a 404. <rewrite> <globalRules> <rule name="TFS" stopProcessing="true"> <match url="^(?:tfs/)?(.*)" /> <conditions> <add input="{HTTP_HOST}" pattern="^tfs.server.domain.com$" /> </conditions> <action type="Rewrite" url="http://localhost:8080/tfs/{R:1}" /> </rule> </globalRules> </rewrite> EDIT I actually got this working by adding a binding for the site on port 80 with host name tfs.server.domain.com. But using tfs.server.domain.com, I can't authenticate using Windows Authentication. Is there something that I need to configure for Windows Authentication? You can see a trace here: http://pastebin.com/k0QrnL0m

  Read the article

• Deploying a Git server in a AWS linux instance

  - by Leroux

  I'm making a git server on my linux instance in AWS. I tried doing it using these instructions but in the end I always get stuck with a "Permission denied (publickey)" message. So here is my detailed steps, the client is my windows machine running mysysgit and the server is the AWS ubuntu instance : 1) I created user Git with a simple password. 2) Created the ssh directory in ~/.ssh 3) On the client I created ssh keys using ssh-keygen -t rsa -b 1024, they got dropped in my /Users/[Name]/.ssh directory, id_rsa and id_rsa.pub key pair was created. 4) Using notepad I copy pasted the text into newly created files on the server in the ~/.ssh directory of my Git user. ~/.ssh/id_rsa and **~/.ssh/id_rsa.pub** were copied. 5) On the server I made the authorized_hosts file using "cat id_rsa.pub authorized_hosts" (while inside the .ssh directory) 6) Now to test it, on my client machine I did ssh -v git@[ip.address] 7) Result : debug1: Host 'ip.address' is known and matches the RSA host key. debug1: Found key in /c/Users/[Name]/.ssh/known_hosts:1 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey debug1: Next authentication method: publickey debug1: Trying private key: /c/Users/[Name]/.ssh/identity debug1: Trying private key: /c/Users/[Name]/.ssh/id_rsa debug1: Offering public key: /c/Users/[Name]/.ssh/id_dsa debug1: Authentications that can continue: publickey debug1: No more authentication methods to try. Permission denied (publickey). I would appreciate any insight anyone can give me.

  Read the article

• Whitelist IP from google-authenticator in sshd pam

  - by spudwaffle

  My Ubuntu 12.04 server uses the google-authenticator pam module to provide two step authentication for ssh. I need to make it so that a certain IP does not need to type the verification code. The /etc/pam.d/sshd file is below: # PAM configuration for the Secure Shell service # Read environment variables from /etc/environment and # /etc/security/pam_env.conf. auth required pam_env.so # [1] # In Debian 4.0 (etch), locale-related environment variables were moved to # /etc/default/locale, so read that as well. auth required pam_env.so envfile=/etc/default/locale # Standard Un*x authentication. @include common-auth # Disallow non-root logins when /etc/nologin exists. account required pam_nologin.so # Uncomment and edit /etc/security/access.conf if you need to set complex # access limits that are hard to express in sshd_config. # account required pam_access.so # Standard Un*x authorization. @include common-account # Standard Un*x session setup and teardown. @include common-session # Print the message of the day upon successful login. session optional pam_motd.so # [1] # Print the status of the user's mailbox upon successful login. session optional pam_mail.so standard noenv # [1] # Set up user limits from /etc/security/limits.conf. session required pam_limits.so # Set up SELinux capabilities (need modified pam) # session required pam_selinux.so multiple # Standard Un*x password updating. @include common-password auth required pam_google_authenticator.so I've already tried adding a auth sufficient pam_exec.so /etc/pam.d/ip.sh line above the google-authenticator line, but I can't understand how to check an IP adress in the bash script.

  Read the article

• Trouble with local id / remote id configuration of VPN

  - by Lynn Owens

  I have a NetGear UTM firewall and a Windows machine running NetGear's VPN client. The Windows machine I can put on the UTM network and take off of it. When I am cabled into the local (internal) the following configuration works: UTM: Local Id: Local Wan IP: (The UTM's WAN IP address) Remote Id: User FQDN: utm_remote1.com Client: Local Id: DNS: utm_remote1.com Remote Id: (The UTM's WAN IP address) Gateway authentication: preshared key Policy remote endpoint: FQDN: utm_remote1.com But when I'm off the UTM's internal local network and simply coming in from the internet, this does not work. It simply repeats SEND phase 1 before giving up. Since I know that the UTM WAN IP is accessible from both inside and outside the network, I figured the problem was with the Client local id. So, I tried the following: UTM: Local Id: Local Wan IP: (The UTM's WAN IP address) Remote Id: (A DN of a self-signed certificate I created for the client and uploaded into the UTM certificates) Client: Local Id: (The DN of the aforementioned self signed cert) Remote Id: (The UTM's WAN IP address) Gateway authentication: (the aforementioned self signed cert) Policy remote end point: ... er, ... my choices are IP and FQDN.... Not sure what to put here No matter what I've tried, it just keeps repeating the SEND phase 1. Any ideas?

  Read the article

• netlogon errors

  - by rorr

  I have two instances of mssql 2005 and am using CA XOSoft replication. The master is a failover cluster and the replica is a standalone server. They are all running Server 2003 sp2 x64. Same patch levels on all servers. This setup has worked great for several months until we recently restricted the RPC ports on both nodes of the master(5000 - 6000 using rpccfg.exe). We have to implement egress filtering, thus the limiting of the ports. We began receiving login errors for sql windows authentication and NETLOGON Event ID: 5719: This computer was not able to set up a secure session with a domain controller in domain due to the following: Not enough storage is available to process this command. This may lead to authentication problems. Make sure that this computer is connected to the network. If the problem persists, please contact your domain administrator. We also see group policies failing to update and cluster file shares go offline at the same time. The RPC ports were set back to default when we started seeing these problems and the servers rebooted, but the problems persist. The domain controllers are not showing any errors. Running dcdiag and netdiag shows everything is fine. We have noticed that the XOSoft service ws_rep.exe is using a lot of handles(8 - 9k), about the same number that sqlserver is using. As soon as xosoft replication is stopped the login errors cease and everything functions correctly. I have opened a ticket with CA for XOSoft, but I'm not sure that the problem is actually xosoft, but that it is the one bringing the problem to light. I'm looking for tips on debugging RPC problems. Specifically on limiting the ports and then reverting the changes.

  Read the article

• special case ssh connection lag

  - by Hersheezy

  Setup We have a DMZ and LAN in our office that are connected to the outside with the following setup: +------+ | |------> LAN (normal office router) |Modem | | |------> DMZ (a single machine) +------+ Our internet account is with Comcast and we have 5 status IPs, one of which points to the single machine in the DMZ. Problem ssh connections initiated ANYWHERE EXCEPT the office LAN are really fast. However, from the LAN, there is about a 5 second delay. WTF?? Extra info The DMZ machine is debian 5. Executing a wget to the DMZ has no lag. When executing the following, everything up to HERE IS WHERE THE LAG IS INCURRED executes immediately. ssh -vvvv [email protected] ... debug2: set_newkeys: mode 1 debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug3: Wrote 16 bytes for a total of 1015 debug2: set_newkeys: mode 0 debug1: SSH2_MSG_NEWKEYS received debug1: SSH2_MSG_SERVICE_REQUEST sent debug3: Wrote 48 bytes for a total of 1063 debug2: service_accept: ssh-userauth debug1: SSH2_MSG_SERVICE_ACCEPT received debug2: key: /home/shopkins/.ssh/id_rsa (0x22440830) debug2: key: /home/shopkins/.ssh/identity ((nil)) debug2: key: /home/shopkins/.ssh/id_dsa ((nil)) debug3: Wrote 64 bytes for a total of 1127` HERE IS WHERE THE LAG IS INCURRED debug1: Authentications that can continue: publickey,password debug3: start over, passed a different list publickey,password debug3: preferred gssapi-keyex,gssapi-with-mic,gssapi,publickey,keyboard-interactive,password debug3: authmethod_lookup publickey debug3: remaining preferred: keyboard-interactive,password debug3: authmethod_is_enabled publickey debug1: Next authentication method: publickey debug1: Offering public key: /home/shopkins/.ssh/id_rsa debug3: send_pubkey_test debug2: we sent a publickey packet, wait for reply debug3: Wrote 368 bytes for a total of 1495 debug1: Authentications that can continue: publickey,password debug1: Trying private key: /home/shopkins/.ssh/identity debug3: no such identity: /home/shopkins/.ssh/identity debug1: Trying private key: /home/shopkins/.ssh/id_dsa debug3: no such identity: /home/shopkins/.ssh/id_dsa debug2: we did not send a packet, disable method debug3: authmethod_lookup password debug3: remaining preferred: ,password debug3: authmethod_is_enabled password debug1: Next authentication method: password [email protected]'s password:

  Read the article

• Problems with ipsec betwen Cisco ASA 5505 and Juniper ssg5

  - by Oskar Kjellin

  I am trying to set up an ipsec tunnel between our ASA 5505 and a Juniper ssg5. The tunnel is up and running, but I cannot get any data through it. The local network I am on is 172.16.1.0 and the remote is 192.168.70.0. But I cannot ping anything on their netowork. I receive a "Phase 2 OK" when I set up the ipsec. I think this is the part of the config that is applicable. It seems like the data is not routed through the tunnel, but I am not sure... object network our-network subnet 172.16.1.0 255.255.255.0 object network their-network subnet 192.168.70.0 255.255.255.0 access-list outside_cryptomap extended permit ip object our-network object their-network crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto map outside_map 1 match address outside_cryptomap crypto map outside_map 1 set pfs crypto map outside_map 1 set peer THEIR_IP crypto map outside_map 1 set ikev1 phase1-mode aggressive crypto map outside_map 1 set ikev1 transform-set ESP-3DES-MD5 crypto map outside_map 1 set ikev2 pre-shared-key ***** crypto map outside_map 1 set reverse-route crypto map outside_map interface outside webvpn group-policy GroupPolicy_THEIR_IP internal group-policy GroupPolicy_THEIR_IP attributes vpn-filter value outside_cryptomap ipv6-vpn-filter none vpn-tunnel-protocol ikev1 tunnel-group THEIR_IP type ipsec-l2l tunnel-group THEIR_IP general-attributes default-group-policy GroupPolicy_THEIR_IP tunnel-group THEIR_IP ipsec-attributes ikev1 pre-shared-key ***** ikev2 remote-authentication pre-shared-key ***** ikev2 local-authentication pre-shared-key *****

  Read the article

• Does WebDAV even work on IIS 7? I say nay

  - by FlavorScape

  I've tried every configuration from the top 10 stack overflow and server fault results for WebDAV 405 on IIS (for verb PROPFIND and PUT). I'm running server 2008 SP2. Followed all the instructions here. I'm no stranger to configuring servers. This has gotten nowhere after 8 hours. Confirmed system.webserver in applicationhost.config: <add name="WebDAV" path="*" verb="PROPFIND,PROPPATCH,MKCOL,PUT,COPY,DELETE,MOVE,LOCK,UNLOCK" modules="WebDAVModule" resourceType="Unspecified" requireAccess="None" /> Port 443 with basic auth, same issue. Tried port 80 with windows auth. Broken. (405) Windows authentication. Check. Added authoring rules for default site and application. Check. Not the firewall. Check. added "Desktop Experience" role feature Tried HTTPS with Basic Authentication on port 443. Does not work. No other services are running like Sharepoint. Check. confirmed user has read/write NT level permissions for the folder/virtual dir tried net use * http://localhost /user:MYDOMAIN\me myPass get error 1920, if I don't authenticate I get error 67 confirmed I'm not applying filtering to WebDAV: <requestFiltering> <fileExtensions applyToWebDAV="false" /> <verbs applyToWebDAV="false" /> <hiddenSegments applyToWebDAV="false" /> 405 - HTTP verb used to access this page is not allowed. The page you are looking for cannot be displayed because an invalid method (HTTP verb) was used to attempt access. SHOULD I JUST GIVE UP? Other questions that helped none: 405 - ‘Method not Allowed’ adding service hosted in IIS7 webdav on iis7.5 - simply cannot make it work http://studentguru.gr/b/kingherc/archive/2009/11/21/webdav-for-iis-7-on-windows-server-2008-r2.aspx

  Read the article

• Are web service handler chains possible under IIS / ASP.NET

  - by Mike

  I'm working with a client who wants me to implement a particular design in an IIS/ASP.NET environment. This design was already implemented in Java, but I am not sure it is possible using Microsoft technologies. In a Tomcat/Java environment one can create so call Handler Chains. In essence a handler runs on the server on which the web service is running and it intercepts the SOAP message coming to the web service. The handler can perform a number of tasks before passing control to the web service. Some of these tasks may refer to authentication and authorization. Moreover, one can create handler chains, such that the handlers can run in a particular sequence before passing control to the web service. This is a very elegant solution, as certain aspects of authentication and authorization can be automatically performed, without the developer of the client application and of the web service having to invest anything in it. The code for the client application and the web service is not affected. You may find a number of articles on internet on this subject by searching on Google for "web service handler chain". I performed searches for web service handlers in IIS or ASP.NET. I get some hits, but apparently handlers in IIS have another meaning than that described above. My question therefor is: Can handler chains (as available in Java and Tomcat) be created in IIS? If so, how (any article, book, forum...)? Either a negative or a positive answer will be greatly appreciated. Mike

  Read the article

< Previous Page | 222 223 224 225 226 227 228 229 230 231 232 233  | Next Page >