Search Results

Search found 40420 results on 1617 pages for 'power line networking'.

Page 226/1617 | < Previous Page | 222 223 224 225 226 227 228 229 230 231 232 233  | Next Page >

• Routing RFC1918 addresses through dd-wrt via a switch

  - by espenfjo

  I am a bit stuck with an experiment of mine. I have a network looking somewhat like this. | Internet | | ---- |Switch| ---- | | Server w/pub IP | DD-WRT router 192.168.1.1 | | RFC1918 clients 192.168.1.0/24 What I want is for the RFC1918 clients to speak directly with each others. On the server with the public IP I have this route: 192.168.1.0/24 dev eth0 scope link and can see that packets are infact reaching the dd-wrt router for 192.168.1.1, even though if I get no answer. Trying to reach one of the RFC1918 clients from the public IP server will get no result, as the dd-wrt router is not announcing that network on to its external interface (arp who-has 192.168.1.107 tell xxx.xxx.xxx.xxx, but no answer). The router being an WLAN dd-wrt router has of course a load of routes, VLANs and interfaces: xxx.xxx.xxx.1 dev vlan2 scope link 192.168.1.0/24 dev br0 proto kernel scope link src 192.168.1.1 192.168.1.0/24 dev eth1 proto kernel scope link src 192.168.1.244 84.215.64.0/18 dev vlan2 proto kernel scope link src xxx.xxx.xxx.xxx 169.254.0.0/16 dev br0 proto kernel scope link src 169.254.255.1 127.0.0.0/8 dev lo scope link 0.0.0.0 via xxx.xxx.xxx.1 dev vlan2 xxx.xxx.xxx.xxx being the public IP, and xxx.xxx.xxx.1 being the default route for the public IP. I am not sure where to continue with this. I would recon that I both need routing on the dd-wrt router, as well as some iptables magic? Why do something this complex? Why not ;) Also, do not mind that "Internet" can get RFC1918 traffic, it wont go outside of the walls. EDIT 1: Following the tip from stew I do indeed get the correct ARP flowing. And adding an iptables rule for allowing traffic from that specific public IPd machine I get traffic between the systems! Oddly enough though, the speed I get from Server w/pub IP - RFC1918 clients are the same as if the traffic were routed out onto the Internet and back. Edit 2: Ok, disconnecting the external Internet connection will still give the same, crappy transfer speed. So it has to be something else. Edit 3: Ok, I guess there are other reasons for this crappy speed. Case closed. :)

  Read the article

• i am not able to connect to the application hosted on port 80

  - by shiva

  I am trying to access an application that is hosted on port 80. When i try the url from my personal computer , the site is not reachable but the same url on the server( which hosts the application) i am able to access the site. When i disable the firewall then i am able to access the site from my pc. So there is some rule which is blocking this port. How do i determine what windows firewall rule is blocking this port. I have disables IIS as well. Kindly point me in the right direction

  Read the article

• Setting up a Network Bridge on Linux VM (Windows 7 Host)

  - by GrandAdmiral

  I would like to use NetEm to simulate a low bandwidth environment while testing an Internet-connected device. My plan is to setup a bridge in a Linux VM (Linux Mint 13) on a Windows 7 host. Unfortunately I'm having trouble setting up the bridge. Then I can use NetEm in the Linux VM to limit the bandwidth to an external device. I went with the following script: ifconfig eth0 0.0.0.0 promisc up ifconfig eth1 0.0.0.0 promisc up Then create the bridge and bring it up: brctl addbr br0 brctl setfd br0 0 brctl addif br0 eth0 brctl addif br0 eth1 dhclient br0 ifconfig br0 up When I run that script, I see the following warning: Rather than invoking init scripts through /etc/init.d, use the service(8) utility, e.g. service smbd reload Since the script you are attempting to invoke has been converted to an Upstart job, you may also use the reload(8) utility, e.g. reload smbd The device connecting to the bridge is able to obtain an IP Address, but it can only ping the IP Address of the bridge (both are 10.2.32.xx). Then after a few minutes, other parts of our network go down. I'm not sure why, but once I kill the bridge the network is fine. Is it possible to setup a network bridge in a Linux VM? Do I need to do something else with the dhclient br0 part of the script? By the way, I'm using VirtualBox. The wired connection is eth0 and the wireless connection is eth1. The wired connection is connecting to the device and the wireless connection is going to the network. Both adapters are set up as bridged adapters with promiscuous mode set to "allow all".

  Read the article

• How do I load balance between two Linux machines?

  - by William Hilsum

  Inspired by the Stack Overflow network, I am now obsessed with HAProxy and trying to use it myself. At the moment, each HAProxy box has got two network cards (well, two configured, I can have a maximum of 4 and wasn't sure if they needed their own one for management between the boxes). On both machines, the backend one (eth1) is a private IP that goes to a switch connected to the webservers, and the front facing one (eth0) has a public internet IP that is routed straight though. In addition, I have created an additional virtual ip for eth0 called eth0:0 which has got a third public ip address. I just about get how to use it for load balancing between multiple web servers that are behind it, but, I am failing to load balance between the two HAProxy boxes - they appear to fight for the virtual IP, but, this does not appear to be a smart solution. Now, by using the virtual shared IP address, this solution appears to work and does seem to give me maximum uptime, but, is this the correct way to do it, or is there a smarter way? I have been looking at other Linux packages such as keepalived, but, I have only been using Linux (server) for a week now and am at the limits of my understanding. Is there anyone who has done this before and can you advise anything for maximum uptime?

  Read the article

• Proper line-ending for an open-source PHP project

  - by Mahdi

  What is the proper line-ending preferences for an open-source web project? Obviously it includes source code of PHP, HTML, CSS and Javascript. The source code is managing via Github now, and there are Windows (8 & 7), Linux (Ubuntu) and OSX developers inside the team, which means all the major operating systems. P.S. We are using "Windows" CRLF line-ending, plus "UTF-8 without BOM" right now, without facing any problem, however I think it might be better to use "*nix/OSX" LF style. I heard some stories about the problems that caused by the additional "CR" on Linux or OS X.

  Read the article

• As a student looking for hands-on experience, how should I configure my test lab to accurately reflect a business setting?

  - by Moe

  I'm one class away from my BA IT, I took several classes in general IT. Out of all the books I found just two to be really beneficial, so I'm trying to get the hands on experience. I want to build a small test network that has both wireless and also wired clients, a printer, a laptop, a desktop, and server (I have 2x 1TB drives of data that I want to be available to all computers). What should I do to configure these in a way that will reflect how a small business might be set up, so that I can work towards some meaningful experience.

  Read the article

• Ubuntu 12.04 suddenly cannot connect to WPA2/WPA Personal protected connection. Windows 7 can

  - by d4ryl3

  I have a laptop with Windows 7 and Ubuntu 12.04. I have a Cisco E1200 and when I set it up, it created 2 SSIDs. Let's name them: MyConnection (WPA/WPA2 personal), and MyConnection-Guest (no authentication, guest password entered via web browser). I had no problem connecting to MyConnection before, either in Windows 7 and Ubuntu. But now, I can't access MyConnection on Ubuntu. It just says "connecting..." then disconnects after a while. But I'm able to access the internet (on Ubuntu) when I connect to MyConnection-Guest. MAC filtering is off (even if it's on its MAC address is in the white list). Any idea why I'm unable to connect to MyConnection in Ubuntu? Thanks. Update: My Ubuntu installation can connect to ANY WiFi connection (WPA/WEP/no auth), except for MyConnection. Update2: This is what "The not so easy way" returned: Initializing interface 'eth1' conf '/etc/wpa_supplicant.conf' driver 'default' ctrl_interface 'N/A' bridge 'N/A' Configuration file '/etc/wpa_supplicant.conf' -> '/etc/wpa_supplicant.conf' Reading configuration file '/etc/wpa_supplicant.conf' Priority group 0 id=0 ssid='MyConnection' id=1 ssid='MyConnection' id=2 ssid='MyConnection' id=3 ssid='MyConnection' WEXT: cfg80211-based driver detected SIOCGIWRANGE: WE(compiled)=22 WE(source)=21 enc_capa=0xf capabilities: key_mgmt 0xf enc 0xf flags 0x0 netlink: Operstate: linkmode=1, operstate=5 Own MAC address: xx:xx:xx:xx:xx:xx wpa_driver_wext_set_key: alg=0 key_idx=0 set_tx=0 seq_len=0 key_len=0 wpa_driver_wext_set_key: alg=0 key_idx=1 set_tx=0 seq_len=0 key_len=0 wpa_driver_wext_set_key: alg=0 key_idx=2 set_tx=0 seq_len=0 key_len=0 wpa_driver_wext_set_key: alg=0 key_idx=3 set_tx=0 seq_len=0 key_len=0 wpa_driver_wext_set_key: alg=0 key_idx=4 set_tx=0 seq_len=0 key_len=0 ioctl[SIOCSIWENCODEEXT]: Invalid argument Driver did not support SIOCSIWENCODEEXT wpa_driver_wext_set_key: alg=0 key_idx=5 set_tx=0 seq_len=0 key_len=0 ioctl[SIOCSIWENCODEEXT]: Invalid argument Driver did not support SIOCSIWENCODEEXT wpa_driver_wext_set_countermeasures RSN: flushing PMKID list in the driver Setting scan request: 0 sec 100000 usec WPS: UUID based on MAC address - hexdump(len=16): 16 3b d8 47 9e 24 50 89 96 16 6d 66 35 f3 58 37 EAPOL: SUPP_PAE entering state DISCONNECTED EAPOL: Supplicant port status: Unauthorized EAPOL: KEY_RX entering state NO_KEY_RECEIVE EAPOL: SUPP_BE entering state INITIALIZE EAP: EAP entering state DISABLED EAPOL: Supplicant port status: Unauthorized EAPOL: Supplicant port status: Unauthorized Added interface eth1

  Read the article

• Resolve linux hostname in windows

  - by Martin Giffy D'Souza

  Hi, I have a simple home network with Windows 7 machines and Linux machines (Fedora 12 and 13). I'd like to be able to resolve the Linux machine names from the windows machine. For example: -- Windows 7 ping mylinuxmachine Currently this does not resolve. Any ideas? Thank you, Martin

  Read the article

• Sharing Internet Connection in Windows 7 is so much more frustrated than Windows XP

  - by Phuong Nguyen

  Back to the time of Windows XP, from Properties dialog of my Wireless Connection, I can enable sharing and then select LAN network from the Drop Down List and boom, I can share it with my friend. We just need a LAN cable (either cross or not-cross is OK) and his Laptop will get an auto IP to gain access to internet. But now with the new Windows 7, everything starts to suck. I cannot see the Drop Down List any more in the sharing panel and my friends Laptop cannot get an automatic IP anymore. Am I doing anything wrong over there? How can I gain back the peace I used to have with Windows XP?

  Read the article

• Why times elapsed connecting to a server are different?

  - by user1634619

  I have a small program which connects to a server of my choice and measures the time elapsed to do so. Each time I run it it returns different result. My question is what does this time depend on ? Network congestion for one. If I choose a server that has multiple addresses e.g. google.com the length of physical link may differ from time to time ? Is it safe to assume that it also affects connection time ? Are there any other factors in place ?

  Read the article

• What kind of router do I need to handle multiple external I.P addresses?

  - by user1308743

  I have 3 dedicated I.P addresses going to a location with a few servers, and 1 RVS4000 router. Right now, only one I.P is being used. I would like a router that can use all 3 I.P addresses and I can make rules like this: IP1:80 goes to ServerA IP2:80 goes to ServerB What kind of router/device with what features do I need to handle this? I will need to set 30-40 rules to forward certain ports to certain servers. Only a couple ports will need to go to IP2 or IP3. Thanks

  Read the article

• Access Methods to a computer Using MAC Address

  - by Dimal Chandrasiri

  I have my own wifi network at home & recently when I checked the active clients on the wifi I found out the there is one active client. Router shows the MAC address of this client and I want to Access this computer in order to let him know that he's doing a wrong thing. I dont intent to do any harm to his data. I just want to know a method to send him a message saying "Buy you own wifi". How can I achieve this using a windows 8 computer. Is there any specific softwares that I can use or will the netsend command do the trick! Thank you.

  Read the article

• Adding a Printer to my Print Server Failing

  - by Rudi Kershaw

  So, on the Windows Server page I read the following. Step 4: Add Network Printers Automatically Print Management (Printmanagement.msc) can automatically detect all the printers that are located on the same subnet as the computer on which you are running Print Management, install the appropriate printer drivers, set up the queues, and share the printers. To automatically add network printers to a printer server Open the Administrative Tools folder, and then double-click Print Management. In the Printer Management tree, right-click the appropriate server, and then click Add Printer. On the Printer Installation page of the Network Printer Installation Wizard, click Search the network for printers, and then click Next. If prompted, specify which driver to install for the printer. So, I have got to this point, made sure the printer (Canon MP620) is on and correctly plugged into the network. However, when I click "Search the network for printers", the wizard doesn't find it. Now, I can't get any further. Is there anything I could be doing wrong? How should I proceed moving forwards?

  Read the article

• Wpa supplicant suddenly stopped working

  - by Grzenio

  Hi, Recently my wireless stopped working on my Debian testing system. It just doesn't connect. The best I get (only after a reboot) is that it says it did connect, but failed to get IP address. But usually it just tries to connect, disconnects straight away, connects again etc. so it never manages to associate correctly. I am sure it did work about a month ago, stopped working after recent upgrades from the repository. Any ideas how to find the issue and fix it?

  Read the article

• Use wired LAN adapter by default

  - by Frantumn

  I am trying to find out if there's a way to set up network adapters so that if 2 are connected with network and internet access it will choose one over the other. Scenario: I have seen several computers running Windows 7 or Windows 8 where you are connected to a wireless network, working perfectly. Then when you plug in an Ethernet cable, it still shows the network icon in the taskbar as wireless. I would like to have my computer set up so that if there's an Ethernet cable plugged in, it uses that, and not the wireless adapter. 1) Is this possible / How? 2) Why does it stay on wireless over wired when given the option for both?

  Read the article

• Cisco Switching Module and HSRP interface Tracking

  - by Kyle Brandt

  When using 4 port switching module where each port is configured to switchport access vlan ##, for HRSP should I track the vlan interface or the FastEthernet interface? interface FastEthernet0/0/0 switchport access vlan 10 interface Vlan10 ip address 12.12.12.1 255.255.255.0 int FastEthernet0/1 ip address 192.168.1.2 255.255.255.0 standyby ip 192.168.128.1 standby track ?? ! FastEthernet 0/0/0 or Vlan 10?

  Read the article

• localhost name error with linux machines

  - by coderex

  Hi, CASE 1: I have a Ubuntu machine with name midhun.local I can access this in http://midhun.local/svn ... But its can't access from other machines(both Windows and Linux) through this host name. But it works with http://192.168.1.192/svn CASE 2: I have a another machine(windows) having the host-name myname:555 In this case i can access https://myname:555/svn from other windows machines with the same URL. But if am trying to access from the a Linux machine it will not work with the same URL instead of that https://192.1.168.111:555/svn will work. How can I solve the problem. I need to access via the same name from cross domain. How is it possible in LAN Thanks in advance!!

  Read the article

• Which network management system (NMS) to choose?

  - by QrystaL

  I need to integrate NMS in large enterprise system for data collection purposes. Primary requirements: collection by SNMP great scalability (up to 1,000 devices with 1,000 interfaces each) failover data storage in Oracle DBMS integration API (configuration, data access) Any ideas would be appreciated...

  Read the article

• Monitor network traffic on a per-app basis in OS X?

  - by dougoftheabaci

  Title says it all. I'm looking for an app for OS X that will tell me what applications are using the network and what their in/out is. I can get most of the way there with LittleSnitch but it's the bandwidth part that it fails at. The only app I've come across that comes close is "Rubbernet" and while it does look like it would probably do what I want, it's very expensive (more than LittleSnitch) and doesn't look like it gets regular feature updates. Any recommendations?

  Read the article

• Why my laptop sends ARP request to itself ?

  - by user58859

  I have just started to learn about protocols. While studying the packets in wireshark, I came across a ARP request sent by my machine to my own IP. Here is the details of the packet : No. Time Source Destination Protocol Info 15 1.463563 IntelCor_aa:aa:aa Broadcast ARP Who has 192.168.1.34? Tell 0.0.0.0 Frame 15: 42 bytes on wire (336 bits), 42 bytes captured (336 bits) Arrival Time: Jan 7, 2011 18:51:43.886089000 India Standard Time Epoch Time: 1294406503.886089000 seconds [Time delta from previous captured frame: 0.123389000 seconds] [Time delta from previous displayed frame: 0.123389000 seconds] [Time since reference or first frame: 1.463563000 seconds] Frame Number: 15 Frame Length: 42 bytes (336 bits) Capture Length: 42 bytes (336 bits) [Frame is marked: False] [Frame is ignored: False] [Protocols in frame: eth:arp] [Coloring Rule Name: ARP] [Coloring Rule String: arp] Ethernet II, Src: IntelCor_aa:aa:aa (aa:aa:aa:aa:aa:aa), Dst: Broadcast (ff:ff:ff:ff:ff:ff) Destination: Broadcast (ff:ff:ff:ff:ff:ff) Address: Broadcast (ff:ff:ff:ff:ff:ff) .... ...1 .... .... .... .... = IG bit: Group address (multicast/broadcast) .... ..1. .... .... .... .... = LG bit: Locally administered address (this is NOT the factory default) Source: IntelCor_aa:aa:aa (aa:aa:aa:aa:aa:aa) Address: IntelCor_aa:aa:aa (aa:aa:aa:aa:aa:aa) .... ...0 .... .... .... .... = IG bit: Individual address (unicast) .... ..0. .... .... .... .... = LG bit: Globally unique address (factory default) Type: ARP (0x0806) Address Resolution Protocol (request) Hardware type: Ethernet (0x0001) Protocol type: IP (0x0800) Hardware size: 6 Protocol size: 4 Opcode: request (0x0001) [Is gratuitous: False] Sender MAC address: IntelCor_aa:aa:aa (aa:aa:aa:aa:aa:aa) Sender IP address: 0.0.0.0 (0.0.0.0) Target MAC address: 00:00:00_00:00:00 (00:00:00:00:00:00) Target IP address: 192.168.1.34 (192.168.1.34) Here the sender's mac address is mine(Here I have hiden my mac address). target IP is mine. Why my machine is sending ARP request to itself? I found 3 packets of this type. There was no ARP reply for these packets. Can anybody explain me why it is? (My operating system is windows-7. I am directly connected to a wifi modem. I got these packets as soon as I started my connection.) I want one suggestion also. many places I read that RFC's are enough for study about protocols. I studied the RFC 826 on ARP. I personally feel that is not enough at all. Any suggestion regarding this? Is there more then 1 RFC for a protocol? I want to study about the protocols in very detail. Can anybody guide me for this? Thanks in advance.

  Read the article

• Setting Up My Home Network

  - by Skizz

  I currently have five PCs at home, three running WinXP and two running Ubuntu. They are set up like this: ISP ----- Modem ---- Switch ---- Ubuntu1 -- B&W Printer | |--WinXP1 | |--WinXP2 Wireless |--Colour Printer | |---------Ubuntu2 |---------WinXP3 (laptop) The Ubuntu1 machine is set up as a PDC using Samba and runs fetchmail, procmail, dovecot to get my e-mail and allow me to access the e-mail via imap so I can read the e-mail on any PC. I'd like to set up the network like this: ISP ----- Modem ---- Ubuntu1 ---- Switch ------WinXP1 | | |--WinXP2 B&W Printer Wireless |--Colour Printer | |---------Ubuntu2 |---------WinXP3 (laptop) My questions are: How to configure Ubuntu1 to act as a firewall. How to configure Ubuntu1 to provide a consistant user authentication across the network, at the moment Samba provides roaming profiles for the XP machines but the Ubuntu2 machine has it's own user lists. I'd like to have a single authentication for both XP machines and linux machines so that users added to the server list will propagate to all PCs (i.e. new users can log on using any PC without modifying any of the client PCs). How to configure a linux client (Ubuntu2 above) to access files on the server (Ubuntu1), some of which are in user specific folders, effectively sharing /home/{user} per user (read and write access) and stuff like /home/media/photos with read access for everyone and limited write access. How to configure the XP machines (if it is different from a the Samba method). How to set up e-mail filtering. I'd like to have a whitelist/blacklist system for incoming e-mails for some of the e-mail accounts (mainly, my kids' accounts) with filtered e-mails being put into quaranteen until a sysadmin either adds the sender to a blacklist or whitelist. OK, that's a lot of stuff. For now, I don't want config files*, rather, what services / applications to use and how they interact. For example, LDAP could be used for authentication but what else would be useful to make the administration of the LDAP easier. Once I have a general idea for the overall configuration, I can ask other questions about the specifics. Skizz I have looked around for information, but most answers are usually in the form of abstract config files and lists of packages to install.

  Read the article

• freeradius maximum session time problem

  - by haw3d

  hello I'm using openvpn and free-radius for control user accounts. for maximum session time for an user, free-radius has sqlcounter.conf that control that, but after a connection has disconnected that is useful and cannot destroy a connection. for control account time dynamically i need another script that do that. but should anytime that a connection has established a trigger run. is anyway to fire a custom trigger or script when a connection has established? or any way to control session time dynamically?

  Read the article

• How to detect/list rogue computers connected to a WIFI network without access to the Wifi Router interface?

  - by JJarava

  This is what I believe to be an interesting challenge :) A relative (that leaves a bit too far to go there in person) is complaining that their WIFI/Internet network performance has gone down abysmally lately. She'd like to know if some of the neighbors are using her wifi network to access the internet but she's not too technically savvy. I know that the best way to prevent issues would be to change the Router password, but it's a bit of a PITA having to re-configure all wifi devices... and if the uninvited guest broke the password once, they can do it again... Her wifi router/internet connection is provided by the telco, and remotely managed so she can log-on to their telco account's page and remotely change the router's Wifi password, but doesn't have access to the router status page/config/etc unless she opts out of the telco's remote support and mainteinance service... So, how could she check if there are guests in the wifi with this restrictions and in the most "point and click way"? In this case I'd probably use nmap to look for other devices in the network, but I'm not sure if that's the easiest way to do it. I'm not a wifi expert, so I don't know if there are any wifi-scanning utils that can tell us who's talking to the router... Lastly, she's a Windows user as I guess that'll influence the choice of tools available Any suggestions more than welcome Regards!

  Read the article

• pfsense CARP - wan failure on firewall

  - by eldblz

  I have recently configured 2 firewall (on 2 DELL PowerEdge R210II with ESXI 5.1) with pfsense. We have several LANs and 2 WANs. Everything is running fine but i have a strange behavior: i can access internet from alla LANs but not from the firewall (itself). For example the firewall cannot retrive package information or if i setup a gatway monitor ip (like google 8.8.8.8 ) this fails. These are the screenshots of firewall configuration: http://imgur.com/a/LNuMz#0 ATM i kept firewall rules to minimum to avoid problem or conflicts. Any ideas how to solve the problem? Thank you in advance.

  Read the article

• Wireless traffic stops when downloading large files at high speed: packets lost (Linksys WRT120N router)

  - by Torious

  The problem Note: First I'd like to understand WHY this is happening. Ofcourse, a solution would be nice too. :) When downloading a large file over HTTP at high-speeds, my wireless traffic basically stops: I can't open webpages and the download itself pauses. It pauses pretty much immediately after starting it; sometimes at 800 KB, sometimes at a few MB. After some time, the download (and other traffic) resumes, but the problem keeps reoccurring during the same download. The problem does not occur when using a wired connection through the same router (Linskys WRT120N). Also note that the connection is not dropped when this happens. It's just that the traffic stops and I can't browse to web pages, etc. (SYN packets are sent but nothing is received, etc.) Inspection with Wireshark shows that the following happens: Server sends data packets which are acknowledged by client Server sends a packet, but SEQ indicates some packets were lost (6 packets in one occurrence). Server sends a few more packets and client acknowledges these using "selective acknowledgement" Server stops sending data for a while (since the lost packets were not acknowledged or the router stops forwarding them?) Eventually, server does a "retransmission" and traffic resumes as normal. This all seems normal behavior to me when packet loss occurs. It's the consistent packet loss throughout a large, high-speed download that puzzles me. What might cause this? My own idea is the following: My internet is pretty fast (100 mbps), so when starting a large-file download, the router buffers the incoming data (since wireless introduces some slight delay / lower speed, in part due to other networks), but the buffer overflows and the router drops packets to regulate traffic (and because it has no choice). But how could that happen? Doesn't the TCP window size limit the amount of data that can go unacknowledged? So how can the router's buffer overflow if there can only be like 64 KB waiting to be acknowledged? Note: I've disabled TCP window scaling and dynamic window size through netsh options, in an attempt to fix this, but it doesn't seem to matter. Also, Wireshark shows a pattern of the server sending 2 packets (of 1514 bytes) and the client sending an ACK, so does that rule out a possible buffer overflow? And a few more subsequent packets are received... I'm at a loss here. Thanks for any insights. Things that are (probably) NOT the cause / I have experimented with The browser Various TCP options in Windows 7 (netsh etc.) Router settings such as MTU, beacon interval, UPnP, ...

  Read the article

< Previous Page | 222 223 224 225 226 227 228 229 230 231 232 233  | Next Page >