Search Results

Search found 6489 results on 260 pages for 'office automation'.

Page 228/260 | < Previous Page | 224 225 226 227 228 229 230 231 232 233 234 235  | Next Page >

• Route return traffic to correct gateway depending on service

  - by Marnix van Valen

  On my office network I have two internet connections and one CentOS server running a website (HTTPS on port 443). The website should be publicly accessible through the public IP of the first internet connection (ISP-1). The other internet connection, ISP-2, id the default gateway on the network. Both internet connections have routers (the household-kind) with NAT, SPI firewalls etc. The router on ISP-2 is a Netgear WNDR3700 (aka N600) with original firmware. The problem is that the website is unreachable. Looks like incoming traffic on ISP-1 will reach the server but the returning traffic is routed through ISP-2, effectively making the site unreachable. As far as I can tell I can't do port based routing on the WNDR3700. What are my options to make this work? I've been looking at implementing an iptables / routing based solution on the server itself but haven't been able to make that work. Update: Note that the server has one network interface connecting it to both routers.

  Read the article

• windows 7 turns off itself everyday at about 9am

  - by Radek

  I was given this comp at work and after a week or so this strange thing started to happen in the middle of doing something :-( It turns off itself at about 9.10am every morning Just once a day and it works fine after it had it little nap. it happens both if the comp was on all night or I turned it off before leaving the office. I tried to swapped the memory as I was told that there was an issue with memory. But moving or removing any memory did not make any difference. I am not aware that I would install any program that could cause that. I installed AVG and set it up to do every day scan about 8am + if restart is needed it requires user confirmation. 'The Software Protection service has stopped' few minutes before it turned off itself but it happened also at other times without the computer turned off. I turned off Windows automatic updates as the first thing when I got the comp configuration Windows 7 Ultimate Intel Core2 Quad Q9550 at 2.8GH, 8GB RAM ST31000528AS Barracuda 7200.12 SATA 3Gb/s 1TB Update Below message are logged when I turn the comp on again. Message 1: The previous system shutdown at 9:08:54 AM on ?6/?29/?2010 was unexpected. Message 2: Level:Critical Source: Kernel Power EventID 41 Task Category (63) The system has rebooted without cleanly shutting down first. This error could be caused if the system stopped responding, crashed, or lost power unexpectedly. Log after manual restart Update 2 (task scheduler)

  Read the article

• Client unable to access OWA website after temporarily changing SSL certificate on the server

  - by Lorenz Meyer

  I have the following issue: One client computer (Windows XP) cannot access the OWA website. All other client computers can (Except another one in the same remote office). How this happened: I temporarily changed the SSL certificate on the Exchange Server yesterday. After a few minutes, I reverted back, an now the same certificate that was installed for years is back again. During these few minutes, they were in OWA on this computer and got a certificate error. What exactly happens: Internet Explorer displays the error Internet Explorer cannot display the webpage, Firefox displays The connection was reset and Crome shows This webpage is not available. The connection to ... was interrupted. What I already did to try to get this working: Restart the client computer Restart the exchange server Deleted Internet Explorer browsing history In IE, Internet Options, tab Content, under Certificates deletes SSL cache Restored Internet Explorer to the default parameters I looked into certmgr.msc, but did not find a certificate related to the issue What could I do else to narrow down the origin of this problem (or better: resolve it) ? Can you give any advice ?

  Read the article

• Will wear induced by turning computers off in the evening be offset by energy savings?

  - by sharptooth

  I'm asking this here because this is primarily a huge office scenario and administrators will more likely have the answer I'm looking for. Employees' desktop computers can be either left turned on for the whole night or switched off in the evening and turned back on in the morning. The latter will surely save energy. In the same time turning on and off is very harmful for the equipment - hardware often breaks specifically when turned on. Both energy and hardware replacements cost money. With energy it's quite obvious - you pay every month according to what your power meter shows. With hardware replacements it's worse - you need qualified stuff to quickly diagnose the problems and once something breaks the affected employee will have to wait for some time while his computer is fixed/replaced and the data is recovered. So the company has to choose between saving money on energy and saving money on computer maintaince and lost hours. Such decisions must be well though. Is there any detailed study of how turning computers off each evening affects their lifetime?

  Read the article

• Log shipping on select tables.

  - by Scott Chamberlain

  I know I am most likely using incorrect terminology so please correct me if I use the wrong terms so I can search better. We have a very large database at a client's site and we would like to have up to date copies of some of the tables sent across the internet to our servers at our office. We would like to only copy a few of the tables because the bandwidth requirement to do log shipping of the entire database (our current solution) is too high. Also replication directly to our servers is out of the question as our servers are not accessible from the internet and management does not want to do replication (more on that later). One possible Idea we had is to do some form of replication on the tables we need to another database on the same server and do log shipping of that second smaller database but management is concerned that the clients have broken replication (it was between two servers on their internal network however) on us in the past and would like to stay away from it if possible. Any recommendations would be greatly appreciated. If using some form of replication is the only solution, I am not against replication, I just need compelling arguments to convince management to do it. This is to be set up on multiple sites that are running either Sql2005 or Sql2008 we will have both versions on our end to restore the data to so that is not a issue. Thank you.

  Read the article

• How to backup a large FreeNAS?

  - by Ze'ev

  We have a 12TB FreeNAS box in the office, and are looking for a way to keep a backup of it offsite. We're considering (1) tape; (2) a bunch of bare drives (popped into a spare hotswap bay); (3) external drives. Any advice on which solution is best? (Online backup is not an option because our internet connection is too slow.) And, is there some software that will keep track of which files have been backed up and which haven't? So that when one backup unit fills up, we can continue the backup on the next? (We don't want to have to back up to a 12TB device.) This software could run, preferably, on the NAS itself; or from one of our Mac clients. Our goal is a situation where we attach some backup device; it automatically fills up with stuff from the server; the contents of this unit are catalogued somewhere something prompts us to replace with a fresh drive/tape; backup continues until full, including any files that have changed since being backed up.

  Read the article

• What's the best / easiest way to combine two mailboxes on Exchange 2007?

  - by jmassey

  I've found this and this(2) (sorry, maximum hyperlink limit for new users is 1, apparently), but they both seem targeted toward much more complex cases than what I'm trying to do, and I just want to make sure I'm not missing some better approach. Here's the scenario: 'Alice' has retired. 'Bob' has taken over Alice's position. Bob was already with the organization in a different but related position, and so they already have their own Exchange account with mail, calendars, etc., that they need to keep. I need to get all of Alice's old mail, calendar entries, etc., merged into Bob's existing stuff. Ideally, I don't want to have all of Alice's stuff in a separate 'recovery' folder that Bob would have to switch back and forth between to look at older stuff; I want it all just merged into Bob's current Inbox / Calendar. I'm assuming (read: hoping) that there's a better way to do this than fiddling with permissions and exporting to and then importing from a .pst. Office version is 2007 for everybody that uses Exchange, if that helps. Exchange is version 8.1. What (preferably step-by-step - I'm new to Exchange) is the best way to do this? I can't imagine this is an uncommon scenario, but my google-fu has failed me; there seems to be nothing on this subject that isn't geared towards far more complex scenarios. (2): h t t p://technet.microsoft.com/en-us/library/bb201751%28EXCHG.80%29.aspx

  Read the article

• How to download large files when the download size is restricted ?

  - by Rahul

  ? In my office, the network admin has restricted the download limit to a size of 1.8MB for any file. This is for sub ordinates accounts only. But for my manager's PC, there are no restrictions. Is there any way to download files from my PC by using my managers' ip address. I just tried using his ip on my pc but, had the same problem. ? Earlier I was given access to our Linux server from my pc using putty. Then I used to download large files on to the server and then transfer from server to my machine using fire ftp. This transfer worked perfectly fine. But, now I don't have any access to the server. So can I be able to download large files using fire ftp from my own PC ? I'm using Windows XP machine. Please suggest a solution by any possible combination. Thanks.

  Read the article

• Windows VPN always disconnects after < 3 minutes, only from my network

  - by hemp

  First, this problem has existed for almost two years. Until serverfault was born, I pretty much gave up on solving it - but now, hope is reborn! I've set up a Windows 2003 server as a domain controller and VPN server at a remote office. I am able to connect to and work over the VPN from every windows client I've tried, including XP, Vista, and Windows 7 without issue, from at least five different networks (corporate and home, domain and non.) It works fine from all of them. However, whenever I connect from clients on my home network, the connection drops (silently) after 3 minutes or less. After a short while, it will eventually tell me the connection has dropped and attempt to redial/reconnect (if I've configured the client that way.) If I reconnect, the connection will re-establish and appear to work correctly, but again will silently drop, this time after a seemingly shorter time period. These are not intermittent drops. It happens every single time, in exactly the same way. The only variable is how long the connection survives. It doesn't matter what type of traffic I send. I can sit idle, send continuous pings, RDP, transfer files, all of that at once - it makes no difference. The result is always the same. Connected for a few minutes, then silent death. Since I doubt anyone has experienced this exact situation, what steps can I take to troubleshoot my evanescing VPN?

  Read the article

• Is 2 GB of RAM better than 2.5 GB?

  - by pibboater

  My laptop has two slots for RAM, and currently has two 512 MB chips, for 1 GB. Windows XP is running terribly slow on it, so I want to upgrade the RAM. I could buy two 1 GB chips to replace both of the current 512 MB chips, to give me 2 GB of RAM. Or, the price is the same to buy one 2 GB chip, to replace just one of the 512 MB chips, and give me 2.5 GB total. The RAM it takes is PC2-4200 533MHz DDR2. What do you think would be better: buying two 1 GB chips so it can take advantage of dual-channel operation, or buying one 2 GB chip to end up with more total RAM but not dual-channel operation? Like I said, price is the same, so performance is the only consideration. I'm not doing anything especially intensive like video or photo editing -- just having multiple Office programs open, playing music, browsers, etc., but currently even opening the first application takes forever. If it matters, the laptop is a Toshiba Qosmio G25-AV513 running Windows XP Media Center SP3. Thanks! Kevin

  Read the article

• no administrator password for Windows 7

  - by huskergirl78

  I'm a secretary and my boss set up my new Windows 7 OptiPlex 7010 (Dell) computer for me while I was on vacation (he does not remember setting any "administrator" password). We are a small office so there is no system password set, either. I've used it for 6 months, all the while I couldn't access network drives, etc., without an administrator password. It was annoying, but I could still get my work done. Finally, on a slow day I took it upon myself to "fix" the problem, and in all my infinite wisdom, I managed to change my user account from administrator to standard user, so now I really can't do anything. I can't download or install any programs, move or rename files, etc. I tried the Dell suggested solution, but the BIOS tells me there is no password set, so it has to be a Windows 7 problem. All the solutions I have come across require an administrator password to let me do them. What can I do to find out the admin password so I can use my own darn computer!? Is there a default admin password?

  Read the article

• Strange problem with Google Mail and IMAP on Outlook 2007

  - by Alex C.

  I work for a small non-profit organization. We have about 35 administrative employees who use e-mail. We're on a Windows network with a domain. Everyone is running XP Pro and Office 2007 with all updates/patches. We used to use POP3 mail through a local provider. However, we recently signed-up for a free Google Apps account, and we switched to IMAP mail through Google. Everyone uses Outlook 2007 as the client. For about ten days, everything was working fine. Yesterday afternoon, we suddenly developed a strange and annoying problem. Every time you send an e-mail message, a copy of your outgoing message shows up in your inbox. It's as if you're adding your own address to the CC: line of every message. Nothing has changed on our end. I was hoping that the problem was a temporary glitch that would resolve itself, but here we are about 24 hours later, and it's still happening. I searched Twitter, and there were a handful of vague messages about issues with Google mail and IMAP, but I didn't see any references to this specific problem. Any thoughts on what's going on here and how to fix it?

  Read the article

• Juniper NetScreen NS-5GT traffic monitoring

  - by blah

  I've done casual research into the subject and am truly dismayed at the lack of compatible tools for such a simple task. Maybe someone can provide assistance. We have a NetScreen NS-5GT in the office. I need to be able to get a glance of current traffic per endpoint -- I think the equivalent of 'get sessions' with byte counts/rates. I don't care about bars, graphs, and reports. Something as simple as a classic software firewall display would be perfect. I can't shell out money on something real like SolarWinds products, so a free solution is essential. I'm willing to do a little work but refuse to program something from scratch. It's not prudent right now for me to install a hub or otherwise mess around physically. There must be something out there I can use, maybe in combination. I don't believe I'm asking too much. Specific answers only please, e.g. monitoring software you know will actually work with this antiquated device. I've read about general approaches to the broader problem dozens of times already.

  Read the article

• Driver denied access to PCI card

  - by Corin

  Alright, I asked this on StackOverflow (here) and they suggested trying ServerFault to get help on permissions. So here's the deal. We designed a custom PCI card and wrote the driver for it. It's been working for years without problems but now we encountered one particular installation were it doesn't work. The problem is that we cannot connect to the PCI to begin communication with it. We tried replacing the card and had the same problem. We had the motherboard replaced thinking the PCI slots were bad. That didn't help either. We tried the cards in a different computer and they all worked. So it seemed to be something specific to the computer. The Windows Device Manager indicates the device is working properly and seems to have all the correct driver info. We now have this troublesome computer back at the office for testing. With the help of some extra debug info in the driver we determined that we cannot connect because access is denied. Sounds like a permissions issue to me. I should note that we are logged into the system as a local administrator. So what configuration option in Windows can prevent access to a device?

  Read the article

• windows 7 monitor instantly resumes from power off

  - by user167328

  It seems that some service or program is preventing my monitor from going into power save mode but I cannot find a way to dig down the cause. Does anybody know a way to find out which event may be causing the problem? Background information: If I leave/lock my computer I want to immediately power off the monitor. Stupid windows has no program for this so I use a third party utility. I use Display.exe from Noel Danjou since 2005 and have had no problem with it on XP, my Notebook with w7 x64 pro and at the office with w7 x64 enterprise. With my new home pc with w7 x64 pro the monitor goes off but instantly comes back on after a second. So I tested using a power plan with the shortest timeout of 1 minute but with that the display never goes off at all. (Setting a power plan timeout is no useful option because then I cannot read a document or watch a movie without the monitor going off) I could try trial and error methods but this is cumbersome and not what I regard as a professional solution. So I would prefer a way to analyze the windows events to find out the reason for the display staying active. Add On: In the meantime I tried safe mode and also exited from all tray programs but the problem is still there. I also checked the BIOS for special power settings but still no solution (P.S. Mobo is H87-G41 PC Mate with latest BIOS rev.)

  Read the article

• User-unique .vimrc file for servers as root user

  - by Scott

  I'm getting thrown into an IDE war at the office, where multiple users have root access on our servers, and like to have everything their own way with VIM. Unfortunately, we have our servers locked down enough to where if you want to do anything, you need to have root access. Obviously (although this is obviously frowned upon), we get tired of typing sudo before each command we type, which would require that we constantly type in our wonderfully complex passwords that are mandated on us over and over again, so naturally we all just execute the sudo su - command upon login to avoid all of this. Of course, when it comes to VIM and custom .vimrc files, we are often times stepping on someone else's custom .vimrc file, and we have some whacked out functionality in these files that users have that may overwrite functionality that we have no idea about, much less have the patience to learn either. When as root on a linux box, is there any way for all of us to still maintain our .vimrc file without having to overwrite the file over and over again every time someone wants to use VIM? Ideally, we have many virtual machines all with VIM installed, so a universal solution across all servers would be best, and we do have our Microsoft Windows user specific home directories mounted on the servers under /home/username. Any recommendations for accommodating this?

  Read the article

• Clone Microsoft VM > SharePoint issues

  - by Rob

  Hi, We have an existing (production) Hyper-V VM that I want to clone to create a staging server. This server is NOT on a domain/active-directory - uses all local computer accounts. It is Windows 2008 OS, SharePoint 2007, SQL server 2008, Reporting Services, and some custom line-of-business web-applications. We rename the server etc as per the documentation we have, but are having troubles specifically with SharePoint. Some of the sites do not come up, and some issues adding/updating site settings such as site owners. Does anyone know of a definitive resource to this process? thanks Update: We seem to have most working, but the Shared Service Provider, and the SSP's admin site, are not working. In addition, the custom web-parts that reference IIS Session objects are failing (which seem to be related to the Share Service Provider). All the Windows user accounts for various services are renamed during the server cloning, but the windows account names in SQL server are not automatically changed. We've tried to change them in SQL server but still does not seem to work Seems like allot of work - and am thinking that there must be some guidance out there. also getting this: NullReferenceException: Object reference not set to an instance of an object.] Microsoft.Office.Server.Administration.SqlSessionStateResolver.System.Web. IPartitionResolver.ResolvePartition(Object key) +135

  Read the article

• Replacement for public folder workflow, I'm confused as to how sharepoint does it.

  - by RodH257

  For years Microsoft has been slowly phasing out public folders, perhaps exchange 2010 really is the LAST TIME they'll be shipped... I've heard sharepoint is the replacement, but I don't understand full, can someone give me an idea of how to replace this workflow? In our office, we have projects, they have a project number, ie 10353. Each job folder has a public folder, organized in a hierachy like Projects Year Folder Subfolders The main subfolder we use is for genera correspondence. When an email is received that relates to a project, it is dragged and dropped (or right click move to) a public folder. Adding public folder favourites for each user helps this. When an email is sent, we have a custom email form, which is the default email form, but with a project number field next to the subject line. When you enter the job number in there, it carbon copies our filing system in, which reads the job number and puts the email in the public folder for you. if you need to refer to emails, you go to public folder and find them there. This isn't the best with large jobs, but it works ok. Now, I have limited experience with sharepoint (well, WSS), we've used it to do some neat discussion boards/polls etc as an intranet site, but I haven't seen much of its integration with outlook. The great thing about our solution is how tightly it integrates with outlook which is exactly where the emails are. If you want to forward an old email, you go to public folder and forward it, simple. Any solution that replaces it should be at least as easy as this. Improvements we would like would be to have better searching of emails, better support in exchange (ie future version) and also, custom forms in outlook are being phased out (the VBA kind), so avoiding these would be good. Does sharepoint do this? or what solutions do this kind of thing?

  Read the article

• Cisco RV042 VPN with Dynamic IPs - Remote Gateway Not Resolving

  - by Rister

  I have an existing network setup that I inherited from my predecessor. Currently there are two sites, each with a Linksys RV042 VPN router running the 1.3.12.19-tm firmware. They are currently set up with a Gateway to Gateway VPN. One site has a static IP, the other has a Dynamic IP with a hostname set up on no-ip.com. My company is looking to set up another site so I purchased another RV042 only this one was Cisco branded and it is running the latest firmware. I had assumed that I would be able to configure a vpn from our main office (the dynamic ip) to the new site with this router quite easily. However when I set up a new VPN tunnel on either device, it stays on Waiting for Connection and the Remote Gateway shows an ip address of 0.0.0.0 rather than the remote ip address. The other VPN tunnel is still working and I don't see any obvious misconfiguration on the new router. It seems that the router is not resolving the Dynamic DNS address and therefore not giving me the option to connect the VPN. Does a Gateway to Gateway VPN work with Dynamic IP addresses on each end? Are the firmware versions not compatible? Is there something I've missed?

  Read the article

• MS Excel and Access - which is better for reports?

  - by Nat

  Where I work, staff have just started to use a basic table in excel (1 october) to record sales which has about 10 columns (name, client, renewed, discount, paid etc). I record the data (total sold etc) every hour and email it to the manager. Each staff has the their own file on the network which they use constantly for that day (eg. John 08-10.xlsx; John 09-10.xlsx etc) and have been told to save the file after they complete a row with client data. I can see the file (in read only mode) to update the report but I am sure there must be a way of doing an autoupdate of their worksheets in real time. I can link worksheets and workbooks to my main workbook but manually. Does anyone have suggestions on have to do this on Excel? Or would Access allow me to make a report which shows the sales total for that hour without the staff closing the file or constantly clicking save every few minutes? We use office 2010. thanks

  Read the article

• Installed Bunch of New Fonts on Windows 7 - Now None Show Up and System Lags

  - by Josh Stodola

  So I went to install about 5,000 fonts on my Windows 7 64-bit machine. It was slow to install them, and I had to leave. I came back and my PC was shut down, and I had to go through the Windows recovery BS when I powered it on. Now my computer runs EXTREMELY slow and any program that has a font menu locks up my whole machine (nothing in Microsoft Office works). When I go to "Fonts" in the control panel, it says 0 items. I went through all of the font settings trying to get them to appear. Nothing helps. I tried to bring up the Character Map and that froze up my machine too. How can I fix this? If I do not get this issue resolved soon, I am wiping this drive and going back to XP (and probably never purchasing another version of Windows again). I never had any issues with XP and have had nothing but performance problems when switching to Windows 7. My quad-core intel extreme with 8GB of RAM should never flinch with the kind of work that I do, and something simple like playing a song off an external HD takes up to five seconds on Windows 7. Unbelievable that I had to pay for this crap!

  Read the article

• Virtualbox Networking: XP Guest, Ubuntu Host: Connecting to Windows servers & local network?

  - by user51833

  Here's what I have: Windows XP running in VirtualBox 3.0.8_OSE r53138; Host OS = Ubuntu 9.10 "Karmic Koala"; Windows network in my office with smb fileservers; Guest OS is connected to the internet and is sharing folders with Host OS; Limited networking expertise. Here's what I actually need to do: Use MS Outlook in my XP guest with all its calendar-sharing features and stuff (if this is all done through the internet then great) - or find a Linux app that can do the same stuff; Map Windows network servers, eg. smb://server01/ in my XP guest (I can already access these in Ubuntu. Here's what I've tried with no luck: Entering the server address (example above) in my XP guest windows explorer address bar (got a "could not access the file, path or drive" error message - maybe if I could enter login/pass information? But I don't know how); Mapping the server as a network drive (Windows could not find the path); Mounting the server as one of my shared folders (I couldn't find it through the shared folders browser in VirtualBox - is there somewhere in the Linux filesystem that Ubuntu keeps links to mounted servers?).

  Read the article

• Forward all traffic from one IP to another Ip on OS X

  - by Josh

  This is related to this question I just asked... I have two IP address on my iMac I want to "bridge". I'm not sure what the proper terminology is... here's the situation. My iMac has a firewire connection to my laptop and an ethernet connection to the rest of my office. My laptop has an ip of 192.168.100.2 (on the firewire interface). My iMac has an IP of 192.168.100.1 on the firewire interface, and two IPs, 10.1.0.6 and 10.1.0.7, on it's ethernet interface. If I wanted to forward all traffic coming in from 192.168.100.2 on my OS X machine to go out on IP 10.1.0.7, and vice-versa, can this be done? I assume I would use the ipfw command. Essentially I want to "bridge" the firewire network to the ethernet network so my laptop can see all the machines on the 10.1 network, and all those machines can see my laptop at 10.1.0.7. Is this possible?

  Read the article

• Choosing gateway router/firewall for small datacenter network [closed]

  - by rvs

  I'm choosing a gateway router/firewall for small internal network for medium-sized web service. Currently there are 5 servers in internal network, up to 50 http(s) requests/second, up to 1000 simultaneous connections, uplink is 100 Mbit. So, network is relatively small and not very busy and we don't like to buy some pricey monster like cisco or jupiper for this site. Instead we'd like to buy two affordable devices (one for spare), which can handle our workload now and some time in future (it might be up to 2x more in 1 year). I had some experience with Sonicwall NSA, but it seems to be too complex for this site (we don't need most of its features) and even too pricey when buying two of them. So, after some research I've come up with following options: Netgear Prosecure UTM Series (probably UTM25) Zyxel ZyWall Series (USG100 or USG200) Sonicwall TZ 210 Is this a good idea? All of the above seems to be more office products, not datacenter ones. Or we should stick with Sonicwall NSA? Does anyone have any hands-on experience with this models? Maybe some other advices? Thanks.

  Read the article

• How can I fill (not replace) TAB with Spaces in MSWord?

  - by Morteza

  How can I fill (not replace) TAB with Spaces in MS Office Word? In other word, have a look at the following pic: 1 -> 222 -> 3 111 -> 2 -> 333 11 -> 22 -> 33 11 -> 2222 -> 3333 Suppose that - is indicated one TAB. As you see, each column is justified from left. I need to fill each TAB with Spaces, so that the justification not be confused. If I use 'Find & Replace' option to change each TABs to a specific number of Spaces, justification will be confused because each column have its own character number. In other word, if I change each TAB with 6 Spaces, the above will be changed to the follow: 1 222 3 111 2 333 11 22 33 11 2222 3333 My need is as follow (each dot indicate a Space): 1......222......3 111....2........333 11.....22.......33 11.....2222.....3333

  Read the article

< Previous Page | 224 225 226 227 228 229 230 231 232 233 234 235  | Next Page >