Search Results

Search found 58112 results on 2325 pages for 'ajax net'.

Page 2280/2325 | < Previous Page | 2276 2277 2278 2279 2280 2281 2282 2283 2284 2285 2286 2287  | Next Page >

• How to Configure Source NAT (Private IP => Public IP Outbound)

  - by DavidScherer

  I'm running VMWare ESXi Free and have Zentyal SBS 3.2 running as a Gateway. I have 5 Public IPS (CIDR/29, let's call them 69.1.1.1 - 69.1.1.5) and currently Zentyal is bound to 69.1.1.1 as the Gateway, with the other 4 Public IPs set as Virtual Interfaces in Zentyal (wan2-wan5) I have machines sitting on the Private Network (10.34.251.x) that, when going Outbound (to Google for instance) should be seen by the Internet as an IP other than the Gateway (69.1.1.1), this is because our machines need to be able to communicate with 3rd party APIs that expect these requests to come from a specific IP. From what I could find, SNAT (Source NAT) in Zentyal is used to achieve this, but I'm not sure how to configure it and cannot find a specific piece of Documentation for it at Zentyal. I've tried setting this up a couple different ways, with no results and at this point I have no idea if I'm going about this completely wrong, or my lack of experience with networking and the associated terminology is preventing me from placing the correct values in the correct fields. I get the following form to set up "SNAT" rules in Zentyal: Perhaps someone can offer some guidance and definitions for the fields above? SNAT Address Is this the Public IP I want to masquerade? Outgoing Interface Should this by my External NIC (one connected to Public 'Net), or is it the "Private" interface? It sounds as though this should be the External interface as I want the traffic from the internal network sent Out over this Interface (using a different IP than normal, anyway) Source Is the the Source on the internal network (one of the private IPs?), a public IP I want to masquerade as, or something else entirely? Destination Is this a place on the Internet (eg, "Only do this for the Site Google.com"/IP) or am I allowing myself to become confused again? Service I'm assuming this allows me to restrict which services this rule will apply to, but is it for a service on the internal network or a service being accessed on the external network? If I can offer any further details or information to make what I'm trying to do more clear, I will happily do so. Honestly any kind of help here would be very appreciated. I'm not a NetOps or anything even close, I spend most of my day writing code and my entire "team" at this company consists of "me, myself, and I" so while I try to broaden my KB at every possible opportunity, I can only learn so much, so fast and I feel like with networking especially there's just so much, coupled with a learning curve for each solution that likes to (from my limited perspective) use slightly different terminology that what I'm used to (and I don't exactly have the necessary experience to cross reference this stuff with the stuff I already know in context).

  Read the article

• iptables : how to correctly allow incoming and outgoing traffic for certain ports?

  - by Rubytastic

  Im trying to get incoming and outgoing traffic to be enabled on specific ports, because I block everything at the end of the iptables rules. INPUT and FORWARD reject. What would be the appropiate way to open certain ports for all traffic incoming and outgoing? From docs I found below but one has to really define both lines? iptables -A INPUT -i eth0 -p tcp --dport 22 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A OUTPUT -o eth0 -p tcp --sport 22 -m state --state ESTABLISHED -j ACCEPT I try to open ports for xmpp service and some other deamons running on server. Rules: *filter # Allow all loopback (lo0) traffic and drop all traffic to 127/8 that doesn't use lo0 -A INPUT -i lo -j ACCEPT -A INPUT -d 127.0.0.0/8 -j REJECT # Accept all established inbound connections -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT # Allow all outbound traffic - you can modify this to only allow certain traffic -A OUTPUT -j ACCEPT # Allow HTTP # Prevent DDOS attacks (http://blog.bodhizazen.net/linux/prevent-dos-with-iptables/) # Disallow HTTPS -A INPUT -p tcp --dport 80 -m state --state NEW -m limit --limit 50/minute --limit-burst 200 -j ACCEPT -A INPUT -m state --state RELATED,ESTABLISHED -m limit --limit 50/second --limit-burst 50 -j ACCEPT -A INPUT -p tcp --dport 443 -j DROP # Allow SSH connections # The -dport number should be the same port number you set in sshd_config -A INPUT -p tcp -s <myip> --dport ssh -j ACCEPT -A INPUT -p tcp -s <myip> --dport 5984 -j ACCEPT -A INPUT -p tcp --dport ssh -j REJECT # Attempt to block portscans # Anyone who tried to portscan us is locked out for an entire day. -A INPUT -m recent --name portscan --rcheck --seconds 86400 -j DROP -A FORWARD -m recent --name portscan --rcheck --seconds 86400 -j DROP # Once the day has passed, remove them from the portscan list -A INPUT -m recent --name portscan --remove -A FORWARD -m recent --name portscan --remove # These rules add scanners to the portscan list, and log the attempt. -A INPUT -p tcp -m tcp --dport 139 -m recent --name portscan --set -j LOG --log-prefix "Portscan:" -A INPUT -p tcp -m tcp --dport 139 -m recent --name portscan --set -j DROP -A FORWARD -p tcp -m tcp --dport 139 -m recent --name portscan --set -j LOG --log-prefix "Portscan:" -A FORWARD -p tcp -m tcp --dport 139 -m recent --name portscan --set -j DROP # Stop smurf attacks -A INPUT -p icmp -m icmp --icmp-type address-mask-request -j DROP -A INPUT -p icmp -m icmp --icmp-type timestamp-request -j DROP -A INPUT -p icmp -m icmp -j DROP # Drop excessive RST packets to avoid smurf attacks -A INPUT -p tcp -m tcp --tcp-flags RST RST -m limit --limit 2/second --limit-burst 2 -j ACCEPT # Don't allow pings through -A INPUT -p icmp -m icmp --icmp-type 8 -j DROP # Log iptables denied calls -A INPUT -m limit --limit 5/min -j LOG --log-prefix "iptables denied: " --log-level 7 # Reject all other inbound - default deny unless explicitly allowed policy -A INPUT -j REJECT -A FORWARD -j REJECT COMMIT

  Read the article

• Issues with configuration of Apache and mod_auth_sspi

  - by TekiusFanatikus

  I've been able to get this working using XAMP with Apache 2.0.55 and XAMP Apache 2.2.14 without any problems. However, when I attempt to configure our intranet server (Apache 2.0.59), I don't get the same results. The results are that the following variables contain the information desired: $_SERVER["REMOTE_USER"] AND $_SERVER["PHP_AUTH_USER"]. In this case, they are blank. I'm expecting "domain/user_name". Conf file stuff: <Directory "/xxx/xampp/htdocs/"> # # Possible values for the Options directive are "None", "All", # or any combination of: # Indexes Includes FollowSymLinks SymLinksifOwnerMatch ExecCGI MultiViews # # Note that "MultiViews" must be named *explicitly* --- "Options All" # doesn't give it to you. # # The Options directive is both complicated and important. Please see # http://httpd.apache.org/docs/2.2/mod/core.html#options # for more information. # #Options Indexes FollowSymLinks Includes ExecCGI Options Indexes FollowSymLinks # # AllowOverride controls what directives may be placed in .htaccess files. # It can be "All", "None", or any combination of the keywords: # Options FileInfo AuthConfig Limit # #AllowOverride All AllowOverride None # # Controls who can get stuff from this server. # #Order allow,deny #Allow from all Order allow,deny Allow from all #NT Domain Login AuthName "Intranet" AuthType SSPI SSPIAuth On SSPIAuthoritative On SSPIDomain "xxxx" SSPIOfferBasic Off SSPIPerRequestAuth On SSPIOmitDomain Off # keep domain name in userid string SSPIUsernameCase lower Require valid-user </Directory> I would like to note that I've modified the paths to reflect the intranet environment. I'm using the following module: http://sourceforge.net/projects/mod-auth-sspi/ Once the module is installed and the conf file is modified, the intranet environment's server scope isn't populated with the expected variables. Edit #1 <Directory "/path_here"> # # Possible values for the Options directive are "None", "All", # or any combination of: # Indexes Includes FollowSymLinks SymLinksifOwnerMatch ExecCGI MultiViews # # Note that "MultiViews" must be named *explicitly* --- "Options All" # doesn't give it to you. # # The Options directive is both complicated and important. Please see # http://httpd.apache.org/docs/2.2/mod/core.html#options # for more information. # #Options Indexes FollowSymLinks Includes ExecCGI Options Indexes FollowSymLinks # # AllowOverride controls what directives may be placed in .htaccess files. # It can be "All", "None", or any combination of the keywords: # Options FileInfo AuthConfig Limit # #AllowOverride All AllowOverride None # # Controls who can get stuff from this server. # #Order allow,deny #Allow from all Order allow,deny Allow from all #NT Domain Login AuthName "Intranet" AuthType SSPI SSPIAuth On SSPIAuthoritative On SSPIDomain "domain_here" SSPIOfferBasic On SSPIPerRequestAuth On SSPIOmitDomain Off # keep domain name in userid string SSPIUsernameCase lower Require valid-user </Directory>

  Read the article

• Objects won't render when Texture Compression + Mipmapping is Enabled

  - by felipedrl

  I'm optimizing my game and I've just implemented compressed (DXTn) texture loading in OpenGL. I've worked my way removing bugs but I can't figure out this one: objects w/ DXTn + mipmapped textures are not being rendered. It's not like they are appearing with a flat color, they just don't appear at all. DXTn textured objs render and mipmapped non-compressed textures render just fine. The texture in question is 256x256 I generate the mips all the way down 4x4, i.e 1 block. I've checked on gDebugger and it display all the levels (7) just fine. I'm using GL_LINEAR_MIPMAP_NEAREST for min filter and GL_LINEAR for mag one. The texture is being compressed and mipmaps being created offline with Paint.NET tool using super sampling method. (I also tried bilinear just in case) Source follow: [SNIPPET 1: Loading DDS into sys memory + Initializing Object] // Read header DDSHeader header; file.read(reinterpret_cast<char*>(&header), sizeof(DDSHeader)); uint pos = static_cast<uint>(file.tellg()); file.seekg(0, std::ios_base::end); uint dataSizeInBytes = static_cast<uint>(file.tellg()) - pos; file.seekg(pos, std::ios_base::beg); // Read file data mData = new unsigned char[dataSizeInBytes]; file.read(reinterpret_cast<char*>(mData), dataSizeInBytes); file.close(); mMipmapCount = header.mipmapcount; mHeight = header.height; mWidth = header.width; mCompressionType = header.pf.fourCC; // Only support files divisible by 4 (for compression blocks algorithms) massert(mWidth % 4 == 0 && mHeight % 4 == 0); massert(mCompressionType == NO_COMPRESSION || mCompressionType == COMPRESSION_DXT1 || mCompressionType == COMPRESSION_DXT3 || mCompressionType == COMPRESSION_DXT5); // Allow textures up to 65536x65536 massert(header.mipmapcount <= MAX_MIPMAP_LEVELS); mTextureFilter = TextureFilter::LINEAR; if (mMipmapCount > 0) { mMipmapFilter = MipmapFilter::NEAREST; } else { mMipmapFilter = MipmapFilter::NO_MIPMAP; } mBitsPerPixel = header.pf.bitcount; if (mCompressionType == NO_COMPRESSION) { if (header.pf.flags & DDPF_ALPHAPIXELS) { // The only format supported w/ alpha is A8R8G8B8 massert(header.pf.amask == 0xFF000000 && header.pf.rmask == 0xFF0000 && header.pf.gmask == 0xFF00 && header.pf.bmask == 0xFF); mInternalFormat = GL_RGBA8; mFormat = GL_BGRA; mDataType = GL_UNSIGNED_BYTE; } else { massert(header.pf.rmask == 0xFF0000 && header.pf.gmask == 0xFF00 && header.pf.bmask == 0xFF); mInternalFormat = GL_RGB8; mFormat = GL_BGR; mDataType = GL_UNSIGNED_BYTE; } } else { uint blockSizeInBytes = 16; switch (mCompressionType) { case COMPRESSION_DXT1: blockSizeInBytes = 8; if (header.pf.flags & DDPF_ALPHAPIXELS) { mInternalFormat = GL_COMPRESSED_RGBA_S3TC_DXT1_EXT; } else { mInternalFormat = GL_COMPRESSED_RGB_S3TC_DXT1_EXT; } break; case COMPRESSION_DXT3: mInternalFormat = GL_COMPRESSED_RGBA_S3TC_DXT3_EXT; break; case COMPRESSION_DXT5: mInternalFormat = GL_COMPRESSED_RGBA_S3TC_DXT5_EXT; break; default: // Not Supported (DXT2, DXT4 or any compression format) massert(false); } } [SNIPPET 2: Uploading into video memory] massert(mData != NULL); glGenTextures(1, &mHandle); massert(mHandle!=0); glBindTexture(GL_TEXTURE_2D, mHandle); commitFiltering(); uint offset = 0; Renderer* renderer = Renderer::getInstance(); switch (mInternalFormat) { case GL_RGB: case GL_RGBA: case GL_RGB8: case GL_RGBA8: for (uint i = 0; i < mMipmapCount + 1; ++i) { uint width = std::max(1U, mWidth >> i); uint height = std::max(1U, mHeight >> i); glTexImage2D(GL_TEXTURE_2D, i, mInternalFormat, width, height, mHasBorder, mFormat, mDataType, &mData[offset]); offset += width * height * (mBitsPerPixel / 8); } break; case GL_COMPRESSED_RGB_S3TC_DXT1_EXT: case GL_COMPRESSED_RGBA_S3TC_DXT1_EXT: case GL_COMPRESSED_RGBA_S3TC_DXT3_EXT: case GL_COMPRESSED_RGBA_S3TC_DXT5_EXT: { uint blockSize = 16; if (mInternalFormat == GL_COMPRESSED_RGB_S3TC_DXT1_EXT || mInternalFormat == GL_COMPRESSED_RGBA_S3TC_DXT1_EXT) { blockSize = 8; } uint width = mWidth; uint height = mHeight; for (uint i = 0; i < mMipmapCount + 1; ++i) { uint nBlocks = ((width + 3) / 4) * ((height + 3) / 4); // Only POT textures allowed for mipmapping massert(width % 4 == 0 && height % 4 == 0); glCompressedTexImage2D(GL_TEXTURE_2D, i, mInternalFormat, width, height, mHasBorder, nBlocks * blockSize, &mData[offset]); offset += nBlocks * blockSize; if (width <= 4 && height <= 4) { break; } width = std::max(4U, width / 2); height = std::max(4U, height / 2); } break; } default: // Not Supported massert(false); } Also I don't understand the "+3" in the block size computation but looking for a solution for my problema I've encountered people defining it as that. I guess it won't make a differente for POT textures but I put just in case. Thanks.

  Read the article

• Access Control Service v2: Registering Web Identities in your Applications [concepts]

  - by Your DisplayName here!

  ACS v2 support two fundamental types of client identities– I like to call them “enterprise identities” (WS-*) and “web identities” (Google, LiveID, OpenId in general…). I also see two different “mind sets” when it comes to application design using the above identity types: Enterprise identities – often the fact that a client can present a token from a trusted identity provider means he is a legitimate user of the application. Trust relationships and authorization details have been negotiated out of band (often on paper). Web identities – the fact that a user can authenticate with Google et al does not necessarily mean he is a legitimate (or registered) user of an application. Typically additional steps are necessary (like filling out a form, email confirmation etc). Sometimes also a mixture of both approaches exist, for the sake of this post, I will focus on the web identity case. I got a number of questions how to implement the web identity scenario and after some conversations it turns out it is the old authentication vs. authorization problem that gets in the way. Many people use the IsAuthenticated property on IIdentity to make security decisions in their applications (or deny user=”?” in ASP.NET terms). That’s a very natural thing to do, because authentication was done inside the application and we knew exactly when the IsAuthenticated condition is true. Been there, done that. Guilty ;) The fundamental difference between these “old style” apps and federation is, that authentication is not done by the application anymore. It is done by a third party service, and in the case of web identity providers, in services that are not under our control (nor do we have a formal business relationship with these providers). Now the issue is, when you switch to ACS, and someone with a Google account authenticates, indeed IsAuthenticated is true – because that’s what he is! This does not mean, that he is also authorized to use the application. It just proves he was able to authenticate with Google. Now this obviously leads to confusion. How can we solve that? Easy answer: We have to deal with authentication and authorization separately. Job done ;) For many application types I see this general approach: Application uses ACS for authentication (maybe both enterprise and web identities, we focus on web identities but you could easily have a dual approach here) Application offers to authenticate (or sign in) via web identity accounts like LiveID, Google, Facebook etc. Application also maintains a database of its “own” users. Typically you want to store additional information about the user In such an application type it is important to have a unique identifier for your users (think the primary key of your user database). What would that be? Most web identity provider (and all the standard ACS v2 supported ones) emit a NameIdentifier claim. This is a stable ID for the client (scoped to the relying party – more on that later). Furthermore ACS emits a claims identifying the identity provider (like the original issuer concept in WIF). When you combine these two values together, you can be sure to have a unique identifier for the user, e.g.: Facebook-134952459903700\799880347 You can now check on incoming calls, if the user is already registered and if yes, swap the ACS claims with claims coming from your user database. One claims would maybe be a role like “Registered User” which can then be easily used to do authorization checks in the application. The WIF claims authentication manager is a perfect place to do the claims transformation. If the user is not registered, show a register form. Maybe you can use some claims from the identity provider to pre-fill form fields. (see here where I show how to use the Facebook API to fetch additional user properties). After successful registration (which may include other mechanisms like a confirmation email), flip the bit in your database to make the web identity a registered user. This is all very theoretical. In the next post I will show some code and provide a download link for the complete sample. More on NameIdentifier Identity providers “guarantee” that the name identifier for a given user in your application will always be the same. But different applications (in the case of ACS – different ACS namespaces) will see different name identifiers. This is by design to protect the privacy of users because identical name identifiers could be used to create “profiles” of some sort for that user. In technical terms they create the name identifier approximately like this: name identifier = Hash((Provider Internal User ID) + (Relying Party Address)) Why is this important to know? Well – when you change the name of your ACS namespace, the name identifiers will change as well and you will will lose your “connection” to your existing users. Oh an btw – never use any other claims (like email address or name) to form a unique ID – these can often be changed by users.

  Read the article

• Synergy - easy share of keyboard and mouse between multiple computers

  Did you ever have the urge to share one set of keyboard and mouse between multiple machines? If so, please read on... Using multiple machines Honestly, as a software craftsman it is my daily business to run multiple machines - either physical or virtual - to be able to solve my customers' requirements. Recent hardware equipment allows this very easily. For laptops it's a no-brainer to attach a second or even a third screen in order to extend your native display. This works quite handy and in my case I used to attached two additional screens - one via HD15 connector, the other via HDMI. But... as it's a laptop and therefore a mobile unit there are slight restrictions. Detaching and re-attaching all cables when changing locations is one of them but hardware limitations, too. After all, it's a laptop and not a workstation. I guess, that anyone working in IT (or ICT) has more than one machine at their workplace or their home office and at least I find it quite annoying to have multiple sets of keyboard and mouse conquering my remaining space on my desk. Despite the ugly looks of all those cables and whatsoever 'chaos of distraction' I prefer a more clean solution and working environment. This allows me to actually focus on my work and tasks to do rather than to worry about choosing the right combination of keyboard/mouse. My current workplace is a patch work of various pieces of hardware (approx. 2-3 years): DIY desktop on Ubuntu 12.04 64-bit, Core2 Duo (E7400, 2.8GHz), 4GB RAM, 2x 250GB HDD, nVidia GPU 512MB Dell Inspiron 1525 on Windows 8 64-bit, 4GB RAM, 200GB HDD HP Compaq 6720s on Windows Vista 32-bit, Core2 Duo (T5670, 1.8GHz), 2GB RAM, 160GB HDD Mac mini on Mac OS X 10.7, Core i5 (2.3 GHz), 2GB RAM, 500GB HDD I know... Not the latest and greatest but a decent combination to work with. New system(s) is/are already on the shopping list but I live in the 'wrong' country to buy computer hardware. So, the next trip abroad will provide me with some new stuff. Using multiple operating systems The list of hardware above already names different operating systems, and actually I have only one preference: Linux. But still my job as a software craftsman for Visual FoxPro and .NET development requires other OSes, too. Not a big deal, it's just like this. Additionally to those physical machines, there are a bunch of virtual machines around. Most of them running either Windows XP or Windows 7. Since years I have the practice that each development for one customer is isolated into its own virtual machine and environment. This keeps it clean and version-safe. But as you can easily imagine with that setup there are a couple of constraints referring to keyboard and mouse. Usually, those systems require their own pieces of hardware attached. As stated, I don't like clutter on my desk's surface, so a cross-platform solution has to come in here. In the past, I tried it with various applications, hardware or network protocols like X11, RDP, NX, TeamViewer, RAdmin, KVM switch, etc. but the problem in this case is that they either allow you to remotely connect to the other system or exclusively 'bind' your peripherals to the active system. Not optimal after all. Synergy to the rescue Quote from their website: "Synergy lets you easily share your mouse and keyboard between multiple computers on your desk, and it's Free and Open Source. Just move your mouse off the edge of one computer's screen on to another. You can even share all of your clipboards. All you need is a network connection. Synergy is cross-platform (works on Windows, Mac OS X and Linux)." Yep, that's it! All I need for my setup here... Actually, I couldn't believe it myself that I didn't stumble over synergy earlier but 'Get over it' and there we go. And despite the fact that it is Open Source, no, it's also for free. Donations for the developers are very welcome and recently they introduced Synergy Premium. A possibility to buy so-called premium votes that can be used to put more weight / importance on specific issues or bugs that you would like the developers to look into. Installation and configuration Simply download the installation packages for your systems of choice, run the installer and enter some minor information about your network setup. I chose my desktop machine for the role of the Synergy server and configured my screen setup as follows: The screen setup allows you currently to build or connect up to 15 machines. The number of screens can be higher as those machine might have multiple screens physically attached. Synergy takes this into the overall calculations and simply works as expected. I tried it for fun with a second monitor each connected to both laptops to have a total number of 6 active screens. No flaws after all - stunning! All the other machines are configured as clients like so: Side note: The screenshot was taken on Windows 8 and pasted via clipboard into Gimp running on Ubuntu. Resume Synergy is now definitely in my box of tools for my daily work, and amongst the first pieces of software I install after the operating system. It just simplifies my life and cleans my desk. Never again without Synergy!Now, only waiting for an Android version to integrate my Galaxy Tab 10.1, too. ;-) Please, check out that superb product and enjoy sharing one keyboard, one mouse and one clipboard between your various machines and operating systems.

  Read the article

• Is there a switch that will connect directly to my modem and allow my router to serve only as a WiFi connection?

  - by Abner

  Details . . Devices . Internets -50Mbps Cable Internet Modem - Motorola Surfboard Extreme Router - Netgear WNDR3700v3 Switch - D-Link DGS-1008G Wired Ethernet Cable - Cat6_24Awg_ Device Configuration - Modem\Router\Switch . . Internet Usage . Wired Demand XBOX 360 1 Gaming PC 2 PC - HD video . WiFi Demand 3 android + 1 Laptop for browsing and group video chat simultaneously . . Specifics . I am experiencing problems with network speeds and reliability on both wired and wireless connections. On many occasions I experience WiFi Speeds that vary between the 15mbps to 0.50 mbs (or less) and ping ranging from 15ms to 500ms. These results are from when I notice problems with internet lag and run speedtest.net to get details of problems. I have a stretched out floor-plan and old building materials drastically affecting my cellphone signal strength as well). After Reading the "Known Issues" Section on the webpage below http://www.dd-wrt.com/wiki/index.php/Netgear_WNDR3700#Known_Issues I bought the switch and Cat6 cable to increase speed and relieve stress on router in an attempt to fix the symptoms. I thought I'd use the router in a Modem\Switch\Router configuration. I thought I'd only have to use the router for mobile WiFi connections like android or Laptops when necessary (hopefully eliminating the problem caused by the router when subjected to all those demanding Ethernet connections) When I started unboxing the switch, I noticed the manual of this DGS-1008G shows it being connected in the Modem\Router\Switch order and not in the Modem\Switch\Router configuration I was aiming for. I have not been able to find a solid plan to remedy my specific problem without buying another expensive router. I would like to get the speeds I am paying for without buying another router. (My WiFi Adapters would also need to be updated if new router is required, meaning more $$$). I can always sell the switch and get a better one that will bypass the router because my most demanding internet connections are Wired. . . Questions Can I accomplish a Modem\Switch\Router configuration with current switch? Is there a different way to get the wired speed I need while providing WiFi only when necessary? . .

  Read the article

• How does formatting works with a PowerShell function that returns a set of elements?

  - by Steve B

  If I write this small function : function Foo { Get-Process | % { $_ } } And if I run Foo It displays only a small subset of properties: PS C:\Users\Administrator> foo Handles NPM(K) PM(K) WS(K) VM(M) CPU(s) Id ProcessName ------- ------ ----- ----- ----- ------ -- ----------- 86 10 1680 412 31 0,02 5916 alg 136 10 2772 2356 78 0,06 3684 atieclxx 123 7 1780 1040 33 0,03 668 atiesrxx ... ... But even if only 8 columns are shown, there are plenty of other properties (as foo | gm is showing). What is causing this function to show only this 8 properties? I'm actually trying to build a similar function that is returning complex objects from a 3rd party .Net library. The library is flatting a 2 level hierarchy of objects : function Actual { $someDotnetObject.ACollectionProperty.ASecondLevelCollection | % { $_ } } This method is dumping the objects in a list form (one line per property). How can I control what is displayed, keeping the actual object available? I have tried this : function Actual { $someDotnetObject.ACollectionProperty.ASecondLevelCollection | % { $_ } | format-table Property1, Property2 } It shows in a console the expected table : Property1 Property2 --------- --------- ValA ValD ValB ValE ValC ValF But I lost my objects. Running Get-Member on the result shows : TypeName: Microsoft.PowerShell.Commands.Internal.Format.FormatStartData Name MemberType Definition ---- ---------- ---------- Equals Method bool Equals(System.Object obj) GetHashCode Method int GetHashCode() GetType Method type GetType() ToString Method string ToString() autosizeInfo Property Microsoft.PowerShell.Commands.Internal.Format.AutosizeInfo autosizeInfo {get;set;} ClassId2e4f51ef21dd47e99d3c952918aff9cd Property System.String ClassId2e4f51ef21dd47e99d3c952918aff9cd {get;} groupingEntry Property Microsoft.PowerShell.Commands.Internal.Format.GroupingEntry groupingEntry {get;set;} pageFooterEntry Property Microsoft.PowerShell.Commands.Internal.Format.PageFooterEntry pageFooterEntry {get;set;} pageHeaderEntry Property Microsoft.PowerShell.Commands.Internal.Format.PageHeaderEntry pageHeaderEntry {get;set;} shapeInfo Property Microsoft.PowerShell.Commands.Internal.Format.ShapeInfo shapeInfo {get;set;} TypeName: Microsoft.PowerShell.Commands.Internal.Format.GroupStartData Name MemberType Definition ---- ---------- ---------- Equals Method bool Equals(System.Object obj) GetHashCode Method int GetHashCode() GetType Method type GetType() ToString Method string ToString() ClassId2e4f51ef21dd47e99d3c952918aff9cd Property System.String ClassId2e4f51ef21dd47e99d3c952918aff9cd {get;} groupingEntry Property Microsoft.PowerShell.Commands.Internal.Format.GroupingEntry groupingEntry {get;set;} shapeInfo Property Microsoft.PowerShell.Commands.Internal.Format.ShapeInfo shapeInfo {get;set;} Instead of showing the 2nd level child object members. In this case, I can't pipe the result to functions waiting for this type of argument. How does Powershell is supposed to handle such scenario?

  Read the article

• Fedora 11 System - Failed Hard Drive Removed, and Boot gets GRUB Hard Disk Error

  - by Mindful

  Greetings, I have a machine with a 120GB ATA drive that has what I thought to be non-essential data on it. I also have a 320GB SATA hard drive with the OS/Application/Files (good data I want to keep). My 120GB ATA is failing I believe, as my computer kept slowing to a halt. However, when I move the drive from BIOS my computer will not start, says "GRUB Hard Disk Error". I know that my Fedora system has an LVM setup. I am looking to just remove the 120GB drive from "the mix", and just have one hard drive. How do I recover ? Thank you. I have access to a Linux Live CD right now and can make any changes. However, it won't boot into my OS - it fails. UPDATE: here's my Grub.Conf # grub.conf generated by anaconda # # Note that you do not have to rerun grub after making changes to this file # NOTICE: You have a /boot partition. This means that # all kernel and initrd paths are relative to /boot/, eg. # root (hd1,0) # kernel /vmlinuz-version ro root=/dev/VolGroup00/LogVol00 # initrd /initrd-version.img #boot=/dev/sda1 default=0 timeout=5 splashimage=(hd1,0)/grub/splash.xpm.gz hiddenmenu title Fedora (2.6.30.10-105.2.23.fc11.i686.PAE) root (hd1,0) kernel /vmlinuz-2.6.30.10-105.2.23.fc11.i686.PAE ro root=/dev/VolGroup00/LogVol00 rhgb quiet initrd /initrd-2.6.30.10-105.2.23.fc11.i686.PAE.img title Fedora (2.6.30.9-102.fc11.i686.PAE) root (hd1,0) kernel /vmlinuz-2.6.30.9-102.fc11.i686.PAE ro root=/dev/VolGroup00/LogVol00 rhgb quiet initrd /initrd-2.6.30.9-102.fc11.i686.PAE.img title Fedora (2.6.27.24-170.2.68.fc10.i686.PAE) root (hd1,0) kernel /vmlinuz-2.6.27.24-170.2.68.fc10.i686.PAE ro root=/dev/VolGroup00/LogVol00 rhgb quiet initrd /initrd-2.6.27.24-170.2.68.fc10.i686.PAE.img title Fedora (2.6.27.24-170.2.68.fc10.i686) root (hd1,0) kernel /vmlinuz-2.6.27.24-170.2.68.fc10.i686 ro root=/dev/VolGroup00/LogVol00 rhgb quiet initrd /initrd-2.6.27.24-170.2.68.fc10.i686.img title Fedora (2.6.27.21-170.2.56.fc10.i686) root (hd1,0) kernel /vmlinuz-2.6.27.21-170.2.56.fc10.i686 ro root=/dev/VolGroup00/LogVol00 rhgb quiet initrd /initrd-2.6.27.21-170.2.56.fc10.i686.img title Fedora (2.6.27.19-170.2.35.fc10.i686) root (hd1,0) kernel /vmlinuz-2.6.27.19-170.2.35.fc10.i686 ro root=/dev/VolGroup00/LogVol00 rhgb quiet initrd /initrd-2.6.27.19-170.2.35.fc10.i686.img title Upgrade to Fedora 10 (Cambridge) kernel /upgrade/vmlinuz preupgrade repo=hd::/var/cache/yum/preupgrade stage2=http://chi-10g-1-mirror.fastsoft.net/pub/linux/fedora/linux/releases/10/Fedora/i386/os/images/install.img ks=hd:UUID=f11769ba-29bc-46de-8c40-a949720a438e:/upgrade/ks.cfg initrd /upgrade/initrd.img title Win rootnoverify (hd0,0) chainloader +1

  Read the article

• Extending Expression Blend 4 &amp; Blend for Visual Studio 2012

  - by Chris Skardon

  Just getting this off the bat, I presume this will also work for Blend 5, but I can’t confirm it… Anyhews, I imagine you’re here because you want to know how to create an addin for Blend, so let’s jump right in there! First, and foremost, we’re going to need to ensure our development environment has the right setup, so the checklist: Visual Studio 2012 Blend for Visual Studio 2012 OK, let’s create a new project (class library, .NET 4.5): Hello.Extension The ‘.Extension’ bit is very very important. The addin will not work unless it is named in this way. You can put whatever you want at the front, but it has to have the extension bit. OK, so now we have a solution with one project. To this project we need to add references to the following things: Microsoft.Expression.Extensibility (from c:\program files\Microsoft Visual Studio 11.0\Blend\   -- x86 folder if you are on an x64 windows install) Microsoft.Expression.Framework (same location as above) PresentationCore PresentationFramework WindowsBase System.ComponentModel.Composition Got them? ACE. Let’s now add a project to contain our control, so, create a new WPF Application project, cunningly named something like ‘Hello.Control’… (I’m creating a WPF application here, because I’m too lazy to dig up the correct references, and this will add all the ones I need ) Once that is created, delete the App.xaml and MainWindow.xaml files, we won’t be needing them. You will also need to change the properties of the project itself, so it is only a class library. Once that is done, let’s add a new UserControl, which will be this: <UserControl x:Class="Hello.Control.HelloControl" xmlns="http://schemas.microsoft.com/winfx/2006/xaml/presentation" xmlns:x="http://schemas.microsoft.com/winfx/2006/xaml" xmlns:mc="http://schemas.openxmlformats.org/markup-compatibility/2006" xmlns:d="http://schemas.microsoft.com/expression/blend/2008" mc:Ignorable="d" d:DesignHeight="300" d:DesignWidth="300"> <Grid> <TextBlock Text="HELLO!!!"/> </Grid> </UserControl> Impressive eh? Now, let’s reference the WPF project from the Extension library. All that’s left now is to code up our extension… So, add a class to the Extension project (name wise doesn’t matter), and make it implement the IPackage interface from the Microsoft.Expression.Extensibility library: public class HelloExtension : IPackage { /**/ } We’ll implement the two methods we need to: public class HelloExtension : IPackage { public void Load(IServices services) { } public void Unload() { } } We’re only really concerned about the Load method in this case, as let’s face it, the extension we have doesn’t need to do a lot to bog off. The interesting thing about the Load method is that it receives an IServices instance. This allows us to get access to all the services that Expression provides, in this case we’re interested in one in particular, the ‘IWindowService’ So, let’s get that bad boy… private IWindowService _windowService; public void Load(IServices services) { _windowService = services.GetService<IWindowService>(); } Nailed it… But why? The WindowService allows us to register our UserControl with Blend, which in turn allows people to activate and see it, which is a big plus point. So, let’s do that… We’ll create an ‘Initialize’ method to create our new control, and add it to the WindowService: private HelloControl _helloControl; public void Initialize() { _helloControl = new HelloControl(); if (_windowService.PaletteRegistry["HelloPanel"] == null) _windowService.RegisterPalette("HelloPanel", _helloControl, "Hello Window"); } First we check that we’re not already registered, and if we’re not we register, the first argument is the identifier used by the service to, well, identify your extension. The second argument is the actual control, the third argument is the name that people will see in the ‘Windows’ menu of Blend itself (so important note here – don’t put anything embarrassing or (need I say it?) sweary…) There are only two things to do now - Call ‘Initialize()’ from our Load method, and Export the class This is easy money – add [Export(typeof(IPackage))] to the top of our class… The full code will (should) look like this: [Export(typeof (IPackage))] public class HelloExtension : IPackage { private HelloControl _helloControl; private IWindowService _windowService; public void Load(IServices services) { _windowService = services.GetService<IWindowService>(); Initialize(); } public void Unload() { } public void Initialize() { _helloControl = new HelloControl(); if (_windowService.PaletteRegistry["HelloControl"] == null) _windowService.RegisterPalette("HelloControl", _helloControl, "Hello Window"); } } If you build this and copy it to your ‘Extensions’ folder in Blend (c:\program files\microsoft visual studio 11.0\blend\) and start Blend, you should see ‘Hello Window’ listed in the Window menu: That as they say is it!

  Read the article

• Seeking past end of file causes Apache hang, and it never restarts.

  - by talkingnews

  I've actually solved my problem with a better script, but I'm still left wondering why Apache2 hung completely - this is an out-of-the-box ISPCONFIG 3.03 install, everything bang up to date, running perfectly. Until... The troublesome but innocent-looking script: $fp = fopen("/var/log/ispconfig/cron.log", "r"); fseek($fp, -5000, SEEK_END); $line_buffer = array(); while (!feof($fp)) { $line = fgets($fp, 1024); $line_buffer[] = $line; $line_buffer = array_slice($line_buffer, -10, 10); } foreach ($line_buffer as $line) { echo $line; } You get the idea, just a script I found on a forum somwehere. I did this for various logs, since it's a nice easy window on what's occurring (in a protect dir, of course!). One day, the logs having grown large an me having sorted all my cron, scripting and mail queue errors, I thought I was time to start afresh. updated, rebooted, archived and deleted the logs. When I ran my script a couple of hours later, it hung. And hung. 8 minutes I waited. Chrome timed the page out, of course, but the server never came back to life. htop showed /usr/sbin/apache2 -k restart using 100% CPU. Never came back until I did a service apache2 restart. Ran fine, as soon as I hit that logfile again...dead. So, I worked out it was the logfile script, and I worked out that seeking beyond the end of the file wasn't good, and I found a better script http://www.php.net/manual/en/function.fseek.php#90450 But what I'm left wondering is... why didn't something restart or kill the process? How was one hanging page able to bring down the whole server? It's running suphp. I say "out of the box", I've tweaked mysql and apache to fork and reserve sensible amounts of processes for the 512Mb RAM the VPS has, and it'll handle multiple refreshes of large pages, and hadn't hung before. Any ideas how I'd avoid this? Google isn't my friend in this instance beyond the reccs. above about number of processes vs RAM available.

  Read the article

• Trouble with Samba Domain

  - by Arkevius

  I'm having a bit of trouble setting up this Samba domain correctly. I'm getting an Access Denied error when trying to add a Windows XP machine to the domain. I'll go through my scenario in detail, but for those of you wanting a TLDR summary it'll be at the bottom of this post. I have HP Proliant server with Ubuntu 12.04 LTS installed. For this particular environment, I need this server to act as a PDC, file server, and print server. I began by updating and upgrading the packages (of course). Then went to install samba, gnome-desktop, wine, and cpanm. Samba was, of course, for the PDC and file/print services. The GUI was needed because a certain software has to be installed on there that needs a GUI. Wine was needed because the software is Windows-native. And cpanm was for a perl script I have running. For Samba, I went into the smb.conf file and enabled domain logons, changed the workgroup/domain name, the logon script for a per-group basis (netlogon/%g), enabled the netlogon and profiles share, and setup a couple of custom shares for the file service. The printer was added later, and seems to be working just fine. I then restarted the services, and used the net groupmap command to ensure my unix groups were mapped correctly to the Windows groups. After this, I went to a Windows box, and was able to successfully join the domain without a problem. After some fidgeting with the software to get it running on the win boxes from the server (it's a records management system program, which stores it's database files on the server), I went to add another computer to the domain. But now it's saying Access Denied. Before when I had this trouble it was because I forgot to add the group "machines" so Samba could create machine accounts. Thinking this was the case, I manually created the machine account to test this theory. However, it would still give me an Access Denied error. That must mean it has something to do with permissions now, correct? I've been fighting with this server for the past two weeks. If it's not one thing that;s wrong, then it's something else completely different. This would be the third time I've actually reinstalled everything to start over. I'll post snippets of my system settings below. If anything else is needed, just say the word and I'll gather up the info. The unix group 'domadmin' is the Domain Admins group. Samba Administrator account administrator:x:1000:1000:Administrator,,,:/home/administrator:/bin/bash Adminstrator's groups administrator adm cdrom sudo dip plugdev lpadmin sambashare domadmin crimestar Samba's Configuration FIle (a snippet anyways) [global] workgroup = CITYPD server string = BPDServer dns proxy = no log file = /var/log/samba/log.%m max log size = 1000 syslog = 0 panic action = /usr/share/samba/panic-action %d security = user encrypt passwords = true passdb backend = tdbsam obey pam restrictions = yes unix password sync = yes passwd program = /usr/bin/passwd %u passwd chat = *Enter\snew\s*\spassword:* %n\n *Retype\snew\s*\spassword:* %n\n *password\supdated\ssuccessfully* . pam password change = yes map to guest = bad user domain logons = yes logon path = \\%L\srv\samba\profiles\%U logon script = logon.bat add machine script = /usr/sbin/useradd -g machines -c "%u machine account" -d /var/lib/samba -s /bin/false %u domain master = yes usershare allow guests = yes [netlogon] comment = Network Logon Service path = /srv/samba/netlogon/%g guest ok = yes read only = yes browseable = no [profiles] comment = All Printers browseable = no path = /var/spool/samba printable = yes guest ok = no read only = yes create mask = 0700 [print$] comment = Printer Drivers path = /var/lib/samba/printers browseable = yes read only = yes guest ok = no write list = root, @lpadmin [crimestar] comment = "Crimestar DB" path = /srv/crimestar/db valid users = @domadmin, @crimestar admin users = administrator writeable = yes guest ok = no browseable = no create mask = 0666 directory mask = 0777 [crimestarfiles] path = /home/administrator/.wine/drive_c/crimestar admin users = administrator browseable = yes ls -la on /srv/samba/profiles drwxrwxrwx 2 root machines 4096 Nov 21 15:27 . drwxr-xr-x 4 root root 4096 Nov 21 15:28 .. ls -la on /srv/samba/netlogon drwxr-xr-x 6 root root 4096 Nov 21 15:30 . drwxr-xr-x 4 root root 4096 Nov 21 15:28 .. drwxr-xr-x 2 root root 4096 Nov 21 15:30 crimestar drwxr-xr-x 2 root root 4096 Nov 21 18:13 domadmin drwxr-xr-x 3 root root 4096 Nov 21 15:30 guests drwxr-xr-x 2 root root 4096 Nov 21 15:29 users GrouMap list Domain Users (S-1-5-21-2978508755-2341913247-928297747-513) -> users Domain Admins (S-1-5-21-2978508755-2341913247-928297747-512) -> domadmin Domain Guests (S-1-5-21-2978508755-2341913247-928297747-514) -> nogroup TLDR I'm getting an Access Denied error message while trying to join a windows box to a samba domain, even after I successfully joined another computer without a problem. System settings / files are quoted above. Anyone have any ideas or suggestions?

  Read the article

• Routing table with two NIC adapters in libvirt/KVM

  - by lzap

  I created a virtual NAT network (192.168.100.0/24 network) in my libvirt and new guest with two interfaces - one in this network, one as bridged (10.34.1.0/24 network) to the local LAN. The reason for that is I need to have my own virtual network for my DHCP/TFTP/DNS testing and still want to access my guest externally from my LAN. On both networks I have working DHCP, both giving them IP addresses. When I setup NAT port forwarding (e.g. for ssh), I can connect to the eth0 (virtual network), everything is fine. But when I try to access the eth1 via bridged interface, I have no response. I guess I have problem with my routing table - outgoing packets are routed to the virtual NAT network (which has access to the machine I am connecting from - I can ping it). But I am not sure if this setup is correct. I think I need to add something to my routing table. # ifconfig eth0 Link encap:Ethernet HWaddr 52:54:00:B4:A7:5F inet addr:192.168.100.14 Bcast:192.168.100.255 Mask:255.255.255.0 inet6 addr: fe80::5054:ff:feb4:a75f/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:16468 errors:0 dropped:27 overruns:0 frame:0 TX packets:6081 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:22066140 (21.0 MiB) TX bytes:483249 (471.9 KiB) Interrupt:11 Base address:0x2000 eth1 Link encap:Ethernet HWaddr 52:54:00:DE:16:21 inet addr:10.34.1.111 Bcast:10.34.1.255 Mask:255.255.255.0 inet6 addr: fe80::5054:ff:fede:1621/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:34 errors:0 dropped:0 overruns:0 frame:0 TX packets:189 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4911 (4.7 KiB) TX bytes:9 # route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.100.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 10.34.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 169.254.0.0 0.0.0.0 255.255.0.0 U 1002 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 1003 0 0 eth1 0.0.0.0 192.168.100.1 0.0.0.0 UG 0 0 0 eth0 Network I am trying to connect from is different than network the hypervisor is connected to: 10.36.0.0. But it is accessible from that network. So I tried to add new route rule: route add -net 10.36.0.0 netmask 255.255.0.0 dev eth1 And it is not working. I thought setting correct interface would be sufficient. What is needed to get my packets coming through?

  Read the article

• CS, SE, HCI, Information Science, Please recommendation for further education of the former performing art manager seeking career in IT industries? [on hold]

  - by Baek Seungjoo

  IT specialists there J Thank you very much for your collective efforts here, and I got huge help reading your professional comments and advices on each questions I have searched so far! This time, I would like to ask for your practical advices or recommendation on what I am struggling on at this moment. I am currently seeking higher education for my career transition from performing art manager and director to “IT software and/or service development and management specialist”. However, as this field is quite new to me, and there are lots of different work positions, I have no idea which grad major I better pursue in order to get qualification. Of course I know this question could sounds wired as it is kind of personal choice. But my lack of understanding on how IT software companies work in general, your practical and experience-based advice will be great help to me, who spent more than two months of self-research on net. OK. Before my question, here is my plan and history, which are quite different from those currently in IT industry I think… 1) Target Firstly, get career transition into IT service or products companies and get experiences. Eventually, pursue IT entrepreneurship in combination with my arts and cultural production and business expertise. 2) Background Career: performing arts director and manager in theatre-based scale opera and musical Art education in youth BA in literature and Chinese studies (Art & Humanities) MA in Cultural & Creative Industries (Art & Humanities) – dissertation with focus on digital prosumption and the lived experience of the prosumer. (a qualitative research on the agents in the digital world) 2) Personally Huge interest in IT hardware and software, and their trend. Skills to build up, repair, tune PCs -of course this is no more than personal hobby, but shows my interests in this field. 4) Problem Encounter a question “So, what do you think you can contribute practically in this position”. This question turn me down everytime I go through job interviews, and I decided more education in the relevant area. Here are my questions. 1) In terms of work positions in IT software companies, I wonder if I can put the comparison of what “Artists” is to “Arts Manager or Director” is what “Developer” is to “Product Manager”. (Of course, this stereotypical division of Artist-Art Manager is out of sense because the domain overlaps to some extent, and is blurring at least in my field, and they are in different contexts, but just speaking easily.) Normally, artist comes with special arts educations, and they live in their own world of artistic inspiration and creation, and they feel alive in practice and on stages. Meanwhile, from the point of staging and managing productions, the role of art manager is critical as well. Our role cares how the production appeals to the audience in effective way, how to make profit and future sustainable management through that, how to set up future strategy in consideration of the external conditions such as political and social circumstances, audience trend and level, other production trends from on-going and historical perspectives, how and what the production make voice to the society from political, economic, humanitarian stances. So, we need keen eyes on economic, political, and societal environment, have to understand human-being and their desires, must know how to make presentation and attract investors, must have sense in managing and fighting over the limited financial resource, how to extend networking and so on. It is common that the two agents create productions in collaboration (normally not in that ideal way but in conflict and fight though J ). So, we need to know each other’s expertise to some extent, for better production. What are the work positions in IT software industries equivalent to the role of “art manager” in performing arts? From my view, considering developers come with special education in the world of computer science, software engineering, or others (self-education sometimes), and they express themselves with the arts of coding, computer languages on the black screen, and make sort of their artistic production online to the audience, I guess there might be someone who collaborate with developers in creating, managing, and launching IT services or products. 2) Which education among CS, SE, HCI, Information Science, is needed for those seeking such work position? Especially for person like me. (At this moment, Information Science has the highest possibility to get in, since I lack Calculus and Math in undergrad educaiton. But please let me know irrespective of this concern, I think there are ways to back it up if CS or SE education needed in my case) 3) Which field between Information Science and HCI can be more practical background regarding job hungting? And which of them have more demands in job market? AS I checked, HCI is more close to CS than IS in its focus of study area. Thank you very much for your patience reading such a long inquiry, and I appreciate to your efforts in advance. Have a nice day in this beautiful summer.

  Read the article

• How can I create an appointment on a shared Outlook calendar

  - by roryhewitt

  This isn't as basic a question as it may seem. Hence all the descriptive text... I and my team use Outlook 2007. I have my own personal calendar and also I share a calendar with others in my team (which is mainly used to notify everyone of vacations etc.). The others in my team are NOT technical people. I would like to create a shortcut or template that any of us can use to create an appointment in the shared calendar. My initial though was to create a new appointment, but rather than actually put it in the calendar, I would save it as an Outlook Template (.oft) file. Once created, I would send this to my team and tell them to put it in their Templates file and put a shortcut on their desktop. Then, if they want to put a vacation in the shared calendar, they just double-click on the shortcut, change the dates etc. and then save & close it. However, when I do that, it doesn't save the fact that it's an appointment on the shared calendar - it just adds the appointment to the team member's personal calendar. There doesn't seem to be a way to specify a calendar in the template. I've also tried this by saving the template as a .ics or .vcs file, with no better luck. Additionally, if a team member adds an appointment to the shared calendar, other 'sharees' aren't notified, unless the appointment is actually created as a meeting and the other sharees are explicitly invited. I found this online (http://office.microsoft.com/en-us/outlook-help/keep-everyone-informed-about-time-away-from-the-office-HA010209819.aspx) which APPEARS to say that what I want to do isn't built in functionality (since it shows a bunch of steps to go through. I'd PREFER not to have to add this stuff to everyone else's personal calendar directly. So... Is this possible to do, natively (i.e. directly in Outlook)? Would a Sharepoint calendar make more sense and allow this functionality? Is there a way to do what I want which will allow the other team members to be notified? Like I said, I'm looking for as simple an interface as possible - these people aren't going to want to do much more than open something and change dates. Additionally, they're probably not going to have any fancy software on their PC's, although they will be up to date with Java and (maybe) .NET frameworks. Also, before anyone gets funny, yes, this has to work with Outlook 2007, as it's a corporate standard - we're not able to change that, even though e.g. Google Calendar would do this wonderfully. Obviously if this functionality is available in Outlook 2010, then fantastic - we might be able to upgrade. Thanks!

  Read the article

• LINQ and ArcObjects

  - by Marko Apfel

  Motivation LINQ (language integrated query) is a component of the Microsoft. NET Framework since version 3.5. It allows a SQL-like query to various data sources such as SQL, XML etc. Like SQL also LINQ to SQL provides a declarative notation of problem solving – i.e. you don’t need describe in detail how a task could be solved, you describe what to be solved at all. This frees the developer from error-prone iterator constructs. Ideally, of course, would be to access features with this way. Then this construct is conceivable: var largeFeatures = from feature in features where (feature.GetValue("SHAPE_Area").ToDouble() > 3000) select feature; or its equivalent as a lambda expression: var largeFeatures = features.Where(feature => (feature.GetValue("SHAPE_Area").ToDouble() > 3000)); This requires an appropriate provider, which manages the corresponding iterator logic. This is easier than you might think at first sight - you have to deliver only the desired entities as IEnumerable<IFeature>. LINQ automatically establishes a state machine in the background, whose execution is delayed (deferred execution) - when you are really request entities (foreach, Count (), ToList (), ..) an instantiation processing takes place, although it was already created at a completely different place. Especially in multiple iteration through entities in the first debuggings you are rubbing your eyes when the execution pointer jumps magically back in the iterator logic. Realization A very concise logic for constructing IEnumerable<IFeature> can be achieved by running through a IFeatureCursor. You return each feature via yield. For an easier usage I have put the logic in an extension method Getfeatures() for IFeatureClass: public static IEnumerable<IFeature> GetFeatures(this IFeatureClass featureClass, IQueryFilter queryFilter, RecyclingPolicy policy) { IFeatureCursor featureCursor = featureClass.Search(queryFilter, RecyclingPolicy.Recycle == policy); IFeature feature; while (null != (feature = featureCursor.NextFeature())) { yield return feature; } //this is skipped in unit tests with cursor-mock if (Marshal.IsComObject(featureCursor)) { Marshal.ReleaseComObject(featureCursor); } } So you can now easily generate the IEnumerable<IFeature>: IEnumerable<IFeature> features = _featureClass.GetFeatures(RecyclingPolicy.DoNotRecycle); You have to be careful with the recycling cursor. After a delayed execution in the same context it is not a good idea to re-iterated on the features. In this case only the content of the last (recycled) features is provided and all the features are the same in the second set. Therefore, this expression would be critical: largeFeatures.ToList(). ForEach(feature => Debug.WriteLine(feature.OID)); because ToList() iterates once through the list and so the the cursor was once moved through the features. So the extension method ForEach() always delivers the same feature. In such situations, you must not use a recycling cursor. Repeated executions of ForEach() is not a problem, because for every time the state machine is re-instantiated and thus the cursor runs again - that's the magic already mentioned above. Perspective Now you can also go one step further and realize your own implementation for the interface IEnumerable<IFeature>. This requires that only the method and property to access the enumerator have to be programmed. In the enumerator himself in the Reset() method you organize the re-executing of the search. This could be archived with an appropriate delegate in the constructor: new FeatureEnumerator<IFeatureclass>(_featureClass, featureClass => featureClass.Search(_filter, isRecyclingCursor)); which is called in Reset(): public void Reset() { _featureCursor = _resetCursor(_t); } In this manner, enumerators for completely different scenarios could be implemented, which are used on the client side completely identical like described above. Thus cursors, selection sets, etc. merge into a single matter and the reusability of code is increasing immensely. On top of that in automated unit tests an IEnumerable could be mocked very easily - a major step towards better software quality. Conclusion Nevertheless, caution should be exercised with these constructs in performance-relevant queries. Because of managing a state machine in the background, a lot of overhead is created. The processing costs additional time - about 20 to 100 percent. In addition, working without a recycling cursor is fast a performance gap. However declarative LINQ code is much more elegant, flawless and easy to maintain than manually iterating, compare and establish a list of results. The code size is reduced according to experience an average of 75 to 90 percent! So I like to wait a few milliseconds longer. As so often it has to be balanced between maintainability and performance - which for me is gaining in priority maintainability. In times of multi-core processors, the processing time of most business processes is anyway not dominated by code execution but by waiting for user input. Demo source code The source code for this prototype with several unit tests, you can download here: https://github.com/esride-apf/Linq2ArcObjects. .

  Read the article

• Ubuntu 11.10 firewall/gateway - no client internet access

  - by Siriss

  I have read many other posts but cannot figure this out. eth0 is my external connected to a Comcast modem. The server has internet access with no issues. eth1 is internal and running DHCP for the clients. I have DHCP working just fine, all my clients can get an IP and ping the server but they cannot access the internet. I am using ISC-DHCP-SERVER and have set /etc/default/isc-dhcp-server to INTERFACE="eht1" Here is my dhcpd.conf file located in /etc/dhcp/dhcpd.conf ddns-update-style interim; ignore client-updates; subnet 10.0.10.0 netmask 255.255.255.0 { range 10.0.10.10 10.0.10.200; option routers 10.0.10.2; option subnet-mask 255.255.255.0; option domain-name-servers 208.67.222.222, 208.67.220.220; #OpenDNS # option domain-name "example.com"; default-lease-time 21600; max-lease-time 43200; authoritative; } I have made the *net.ipv4.ip_forward=1* change in /etc/sysctl.conf here is my interfaces file: auto lo iface lo inet loopback auto eth0 iface eth0 inet dhcp iface eth1 inet static address 10.0.10.2 netmask 255.255.255.0 network 10.0.10.0 auto eth1 And finally- here is my iptables.conf file: # Firewall configuration written by system-config-firewall # Manual customization of this file is not recommended. *nat :PREROUTING ACCEPT [0:0] :OUTPUT ACCEPT [0:0] :POSTROUTING ACCEPT [0:0] -A POSTROUTING -s 10.0.10.0/24 -o eth0 -j MASQUERADE #-A PREROUTING -i eth0 -p tcp --dport 59668 -j DNAT --to-destination 10.0.10.2:59668 COMMIT *filter :INPUT ACCEPT [0:0] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [0:0] -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT -A INPUT -p icmp -j ACCEPT -A INPUT -i lo -j ACCEPT -A INPUT -i eth1 -j ACCEPT -A INPUT -m state --state NEW -m tcp -p tcp --dport 22 -j ACCEPT -A INPUT -m state --state NEW -m tcp -p tcp --dport 80 -j ACCEPT -A INPUT -m state --state NEW -m tcp -p tcp --dport 443 -j ACCEPT -A INPUT -m state --state NEW -m tcp -p tcp --dport 53 -j ACCEPT -A INPUT -m state --state NEW -m udp -p udp --dport 53 -j ACCEPT -A FORWARD -s 10.0.10.0/24 -o eth0 -j ACCEPT -A FORWARD -d 10.0.10.0/24 -m state --state ESTABLISHED,RELATED -i eth0 -j ACCEPT -A FORWARD -p icmp -j ACCEPT -A FORWARD -i lo -j ACCEPT -A FORWARD -i eth1 -j ACCEPT #-A FORWARD -i eth0 -m state --state NEW -m tcp -p tcp -d 10.0.10.2 --dport 59668 -j ACCEPT -A INPUT -j REJECT --reject-with icmp-host-prohibited -A FORWARD -j REJECT --reject-with icmp-host-prohibited COMMIT I am completely stuck. I cannot figure out why the clients cannot access the internet. Am I missing a service? Is a service not running? Any help would be greatly appreciated. I tried to be as thorough as possible but please let me know if I have missed something. Thank you!

  Read the article

• I want to virtualize my workstation (Tier 1), Looking for Bare Metal Hypervisor for consumer grade components

  - by Chase Florell

  I find myself in this similar bind at least once a year. The bind whereby I'm either upgrading a motherboard, or an OS hard drive. It drives me crazy to have to reinstall Windows, Visual Studio, all my addins, reconfigure my settings etc... every single time. I have a layout and I like and I want to stick with it. My question is... Is there a Bare Metal Hypervisor on the market that will enable me to virtualize my consumer grade workstation? I really want to avoid Host/Client virtualization. Bare Metal is definitely a better way to go for my needs. Is this a good approach, or am I going to suffer some other undesirable side effects by doing this? Clarification My machine has very limited purposes. My primary use is Visual Studio 2010 Professional where I develop ASP.NET MVC Web Applications. The second piece of software that I use (that's system intensive) is Photoshop CS3. Beyond that, my applications are limited to Outlook, Internet Explorer, Firefox, Opera, Chrome, LinqPad, and various other (small) apps. Beyond this, I'm considering working on a node.js project and might run ubuntu on the same hypervisor if possible. System Specs: Gigabyte Motherboard Intel i7 920 12 GB Ram basic 500GB 7200RPM HDD for OS 4 VelociRaptors in Raid 1/0 for build disk Dual GTS250 (512MB) Graphics cards (non SLI) for quad monitors On a side note I also wouldn't be opposed to an alternative suggestion if the limitations are too great. I could install the ESXi (or Zen Server) on my box, and build a separate "thin client" to RDP into the virtual machine. It appears as though RDP supports dual monitors. Edit (Dec 9, 2011) It's been nearly a year since I first asked this question. Since then, there have been a lot of great strides in Hypervisor technology... AND MokaFive is now released for corporate use. I'd love to dig into this question a little more and find out if there is a solid BareMetal Hypervisor for workstations running consumer grade components (IE: not Dell, HP, Lenovo, Etc).

  Read the article

• Alternative Windows Offline Files + Windows Backup + Previous Version Setup

  - by Herson

  Currently our documents are all hosted in a Windows 7 box. Users can access the files using Windows share and the documents are available offline (windows 7 feature). The documents are being backed up daily by Windows 7 backup and restore utility. Users can access previous versions of the file (from the backups) using Windows Explorer "previous versions" feature. This setup is currently working well, except for the following: We would prefer to have access to hourly versions of the file, not daily. The previous version mechanism is tied up to the backup mechanism. Windows 7 performs a full backup every week and incremental backup everyday. The previous versions of a file is actually what are the available in the backups. If you 20GB documents and want to maintain at least three(3) year history, you will use at minimum 3 years * 52 weeks * 20GB or about 3TB even if there are few changes in the documents. Its pretty inefficient use of space. Looking up previous versions of a file is very slow (tens of minutes). This is probably related to the previous issue - Windows has to traverse its all of its backups. I am considering using SVN + autocommit/autoupdate tortoisesvn. It will have the following advantages: Backups are easy and will also backup the whole history of each documents. (Just backup the repository). Creating previous versions can be frequent. I think svn commit / update can be done every two minutes or so. Users can sync over the net. However, I can see the following issues: More conflicts than the original setup because both multiple users can now edit the same file even both are online, i.e. can connect to the SVN repo. The users can off course lock the file first before editing, but that would mean they have to adjust. Delay on propagation of file changes. On windows 7 file sharing, changes made by one online user will be instantaneously available to other online users. With the SVN setup, changes will only be propagated when the users execute the svn add/commit/update sequence. Delay will be probably a few minutes. This workflow will no longer work: "Hi, I just edited document X, can you have a quick look?" I would like to ask the opinion of the community for alternative setups, or improvements on the above setups to work out the kinks.

  Read the article

• Moving default web site to another drive

  - by Chadworthington

  I set the default location from c:\inetpub\wwwroot to d:\inetpub\wwwroot but when I access my .NET 4.0 site get this error: Description: An error occurred during the processing of a configuration file required to service this request. Please review the specific error details below and modify your configuration file appropriately. Parser Error Message: Unrecognized attribute 'targetFramework'. Note that attribute names are case-sensitive. Source Error: Line 105: Set explicit="true" to force declaration of all variables. Line 106: --> Line 107: <compilation debug="true" strict="true" explicit="true" targetFramework="4.0"> Line 108: <assemblies> Line 109: <add assembly="System.Web.Extensions.Design, Version=4.0.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35"/> When I try to Manage the Basic Settings on the Site and click the "Test Settings" button, I see that I have a problem under "authorization:" The server is configured to use pass-through authentication with a built-in account to access the specified physical path. However, IIS Manager cannot verify whether the built-in account has access. Make sure that the application pool identity has Read access to the physical path. If this server is joined to a domain, and the application pool identity is NetworkService or LocalSystem, verify that <domain>\<computer_name>$ has Read access to the physical path. Then test these settings again. 1) Do I need to grant rights to IIS to the new folder? Which user? I thought it was something like IIS_USER or something similar but I cannot determine the correct name of the user. 2) Also, do I need to set the default version of the framework somewhere at the Default Site level or at the Virtual folder level? How is this done in IIS6, I am used to IIS5 or whatever came with XP Pro. 3) My original site had a subfolder under wwwroot called "aspnet_client." How was this cleated? I manually copied it to the corresponding new location. My app was using seperate ASP specific databases for storing session state and role info, if that is relevant. Thanks

  Read the article

• Why is Varnish not caching?

  - by Justin

  I am troubleshooting the setup of Varnish 3.x on my Ubuntu server. I'm running Drupal 7 on two sites set up on the box, via named-based vhosts. Before trying to get Varnish to play nice with Drupal I'm trying to just get Varnish to a PNG from cache. Here are the headers I get from a curl -I request of the PNG file: HTTP/1.1 200 OK Server: Apache/2.2.22 (Ubuntu) Last-Modified: Sun, 07 Oct 2012 21:18:59 GMT ETag: "a57c2-3850-4cb7ea73db6c0" Accept-Ranges: bytes Content-Length: 14416 Cache-Control: max-age=1209600 Expires: Thu, 25 Oct 2012 22:55:14 GMT Content-Type: image/png Accept-Ranges: bytes Date: Thu, 11 Oct 2012 22:55:14 GMT X-Varnish: 1766703058 Age: 0 Via: 1.1 varnish Connection: keep-alive X-Varnish-Cache: MISS Here is the Varnish VCL file I'm using (It's a default VCL configuration designed for Drupal): # Default backend definition. Set this to point to your content # server. # backend default { .host = "127.0.0.1"; .port = "8080"; } # Respond to incoming requests. sub vcl_recv { # Use anonymous, cached pages if all backends are down. if (!req.backend.healthy) { unset req.http.Cookie; } # Allow the backend to serve up stale content if it is responding slowly. set req.grace = 6h; # Pipe these paths directly to Apache for streaming. #if (req.url ~ "^/admin/content/backup_migrate/export") { # return (pipe); #} # Do not cache these paths. if (req.url ~ "^/status\.php$" || req.url ~ "^/update\.php$" || req.url ~ "^/admin$" || req.url ~ "^/admin/.*$" || req.url ~ "^/flag/.*$" || req.url ~ "^.*/ajax/.*$" || req.url ~ "^.*/ahah/.*$") { return (pass); } # Do not allow outside access to cron.php or install.php. #if (req.url ~ "^/(cron|install)\.php$" && !client.ip ~ internal) { # Have Varnish throw the error directly. # error 404 "Page not found."; # Use a custom error page that you've defined in Drupal at the path "404". # set req.url = "/404"; #} # Always cache the following file types for all users. This list of extensions # appears twice, once here and again in vcl_fetch so make sure you edit both # and keep them equal. if (req.url ~ "(?i)\.(pdf|asc|dat|txt|doc|xls|ppt|tgz|csv|png|gif|jpeg|jpg|ico|swf|css|js)(\?.*)?$") { unset req.http.Cookie; } # Remove all cookies that Drupal doesn't need to know about. We explicitly # list the ones that Drupal does need, the SESS and NO_CACHE. If, after # running this code we find that either of these two cookies remains, we # will pass as the page cannot be cached. if (req.http.Cookie) { # 1. Append a semi-colon to the front of the cookie string. # 2. Remove all spaces that appear after semi-colons. # 3. Match the cookies we want to keep, adding the space we removed # previously back. (\1) is first matching group in the regsuball. # 4. Remove all other cookies, identifying them by the fact that they have # no space after the preceding semi-colon. # 5. Remove all spaces and semi-colons from the beginning and end of the # cookie string. set req.http.Cookie = ";" + req.http.Cookie; set req.http.Cookie = regsuball(req.http.Cookie, "; +", ";"); set req.http.Cookie = regsuball(req.http.Cookie, ";(SESS[a-z0-9]+|SSESS[a-z0-9]+|NO_CACHE)=", "; \1="); set req.http.Cookie = regsuball(req.http.Cookie, ";[^ ][^;]*", ""); set req.http.Cookie = regsuball(req.http.Cookie, "^[; ]+|[; ]+$", ""); if (req.http.Cookie == "") { # If there are no remaining cookies, remove the cookie header. If there # aren't any cookie headers, Varnish's default behavior will be to cache # the page. unset req.http.Cookie; } else { # If there is any cookies left (a session or NO_CACHE cookie), do not # cache the page. Pass it on to Apache directly. return (pass); } } } # Set a header to track a cache HIT/MISS. sub vcl_deliver { if (obj.hits > 0) { set resp.http.X-Varnish-Cache = "HIT"; } else { set resp.http.X-Varnish-Cache = "MISS"; } } # Code determining what to do when serving items from the Apache servers. # beresp == Back-end response from the web server. sub vcl_fetch { # We need this to cache 404s, 301s, 500s. Otherwise, depending on backend but # definitely in Drupal's case these responses are not cacheable by default. if (beresp.status == 404 || beresp.status == 301 || beresp.status == 500) { set beresp.ttl = 10m; } # Don't allow static files to set cookies. # (?i) denotes case insensitive in PCRE (perl compatible regular expressions). # This list of extensions appears twice, once here and again in vcl_recv so # make sure you edit both and keep them equal. if (req.url ~ "(?i)\.(pdf|asc|dat|txt|doc|xls|ppt|tgz|csv|png|gif|jpeg|jpg|ico|swf|css|js)(\?.*)?$") { unset beresp.http.set-cookie; } # Allow items to be stale if needed. set beresp.grace = 6h; } # In the event of an error, show friendlier messages. sub vcl_error { # Redirect to some other URL in the case of a homepage failure. #if (req.url ~ "^/?$") { # set obj.status = 302; # set obj.http.Location = "http://backup.example.com/"; #} # Otherwise redirect to the homepage, which will likely be in the cache. set obj.http.Content-Type = "text/html; charset=utf-8"; synthetic {" <html> <head> <title>Page Unavailable</title> <style> body { background: #303030; text-align: center; color: white; } #page { border: 1px solid #CCC; width: 500px; margin: 100px auto 0; padding: 30px; background: #323232; } a, a:link, a:visited { color: #CCC; } .error { color: #222; } </style> </head> <body onload="setTimeout(function() { window.location = '/' }, 5000)"> <div id="page"> <h1 class="title">Page Unavailable</h1> <p>The page you requested is temporarily unavailable.</p> <p>We're redirecting you to the <a href="/">homepage</a> in 5 seconds.</p> <div class="error">(Error "} + obj.status + " " + obj.response + {")</div> </div> </body> </html> "}; return (deliver); } I'm getting a MISS and age 0 every time. If I'm understanding correctly, this means the file isn't being returned from Varnish's cache. Is there a problem with my Varnish config?

  Read the article

• How can the Private Bytes of a process be significantly less than its effect on the system commit charge?

  - by bacar

  On a 64-bit Windows Server 2003, I can see using taskmgr or process explorer that the total commit charge is around 3.5GB, yet when I sum the Private Bytes consumed by each process (by running pslist -m and adding all values under the Priv column) the total comes in at 1.6GB. I know which process seems to be causing this (sqlservr.exe) as when I kill the process, the commit charge drops dramatically. However the process in question is consuming only ~220MB of Private Bytes yet killing the process drops the commit charge by ~1.6GB. How is this possible? How can the commit charge be so significantly greater than Private Bytes, which should represent the amount of committed memory? If some other factor contributes to the commit charge, what is that factor and how can I view its impact in process explorer? Note: I claim that I understand the difference between reserved and committed memory already: my investigations above relate specifically to Private Bytes which includes only committed memory and excludes reserved memory. the Virtual Size of the process in this case is over 4GB, but this should be irrelevant - Virtual Size in procexp represents reserved, not committed memory, and should not contribute to the commit charge. I'm particularly interested in generalised answers to this question: I'm assuming that if sqlservr.exe can behave in this way, that any process potentially could. Further Investigations I notice that pointing Sysinternals VMMap at this process reports a committed "Private Data" of 1.6GB despite Procexp's reported a Private Bytes of 220MB. This is particularly strange given that the documentation for this field in the "Windows® Sysinternals Administrator's Reference" states that: Private Data memory is memory that is allocated by VirtualAlloc and that is not further handled by the Heap Manager or the .NET runtime, or assigned to the Stack category... VMMap’s definition of “Private Data” is more granular than that of Process Explorer’s “private bytes.” Procexp’s “private bytes” includes all private committed memory belonging to the process. i.e. that VMMap's committed "Private Data" should be smaller than procexp's "Private Bytes". Also, after reading the 'Process committed memory' section of Mark Russinovich's excellent Pushing the Limits of Windows: Virtual Memory, he highlights two cases which won't show up in Private Bytes: File mapping views with copy-on-write semantics (however, according to VMMap there is no significant space allocated to Mapped Files). pagefile-backed virtual memory (however, I tried testlimit with the -l flag as suggested, and no significant memory is consumed by pagefile-backed sections)

  Read the article

• Triple (3) Monitors under Linux

  - by widgisoft

  I have a 3 monitor setup (each 1680x1050) via an Nvidia NVS440 (2 GPUs, 2 outputs per GPU totalling 4 outputs); this works fine under Windows XP,7 but caused considerable headaches under Linux (Ubuntu 9.04). I had previously used an XFX 9600GT and the onboard XFX 9300GS to produce the same result but the card was noisy and power hungry and I was hoping that there was some magical switch in the NVS4400 that got rid of this annoying problem - turns out the NVS440 is just 2 cards on one physical PCB :-p (I searched the net high and low for people using this card under Linux but found nothing, if anything the card uses less power and is fan less so I was to benefit from it either way) Anyway, using either set up there were 5 solutions available: Have 3 separate X instances, all un joined Have 3 separate X instances, adjoined by Xinerama Have 2 separate X instances - One using twin-view, both adjoined by Xinerama Have 2 separate X instances - One using twin-view but no Xinerama Have a single Twin-view setup and leave the 3rd screen unplugged :-p The 4rd option, using 2 separate X instances and twinview (but no xinerama) was the best balance in terms of performance and usability but caused 2 really annoying issues You couldn't control (without altering the shortcuts) which screen an application opened onto - and once it was opened you couldn't move it to another screen without opening up terminal and forcing it to move Nvidia's overriding or falsifying of Xinerama breaks and the 2 screens joined by Twin view behave like a single huge screen causing popups to open in the middle of both screens and maximising of windows stretches to the width of the first 2 screens Firefox can only run one instance as the same user so having multiple firefox windows requires at least 2 users The second option "feels" like the right option, but OpenGL is basically disabled and playing any sort of game or even running anything graphical causes a huge performance drop and instability - even trying to run a basic emulator for gba or gens just causes the system to fall over. It works just enough to stare at your desktop and do nothing but as soon as you start doing some work - opening windows, dragging things around - running multiple copies of firefox it just really feels slow. The last open, only going dual screen works perfectly and everything performs as required, full GPU acceleration - two logical screen spaces - perfect, just make it work across GPUs like windows! :-p Anyway, I know RandR was supposed to pick up the slack when it would introduced GPU objects of sorts to allow multiple GPUs to be stitched together to create one huge desktop at a much deeper layer than Xinerama. I was wondering if this has now been fixed (I noticed X server 1.7 is out) and whether anyone has got it running successfully? Again, my requirements are: One huge desktop to drag any window across Maximising of windows to each screen (as XP does) Running fullscreen apps on the primary screen and disabling the mouse from moving onto the others or on all 3 stretched Finally as a side note; I am aware of the Matrox triple (and dual) head splitter but even the price they go for on eBay is more than I can afford atm, my argument: I shouldn't have to buy extra hardware to get something to work on Linux when it's something that's existed in the windows world for a long time (can you tell I don't get on with X :-p); If I had the cash I'd have bought the latest version of this box already (the new version finally supports large resolutions as the displays I have 1680x1050 each).

  Read the article

• How to fix Ubuntu 12.04.3 boot to black screen full of errors in white text, after upgrading on dell inspiron 1501

  - by Ibuntu

  I am running a Dell Inspiron 1501 I use Linux only. No Microsoft or Apple operating systems (or really anything closed-source). I've only been using Linux for a little over a year but I'm starting to gain a comfortable level of familiarity with the system and terminology. I've been having some issues with Quantel Quetzal and Raring Ringtail, especially with older hardware, so I opted to install Ubuntu 12.04.3 Precise Pangolin on the Inspiron 1501. I checked my MD5 sum after downloading my ISO and all was good. I have in fact used this iso/dvd to install Precise Pangolin successfully on a few other systems (some of which are even older than this laptop). Install goes fine. The wireless card doesn't work out of the box but this is a known issue which is fairly easy to fix. So, first thing I did was open up a terminal and run sudo apt-get update && sudo apt-get upgrade which, part way through, crashed (I assume lightdm and possibly X) and took me to a black screen filled with white lines of text that were either errors or just the ouputs of commands. The reason I say that is because I was unable to gleam any useful information from the output on the screen. I did take a picture however and will post a link. After that, every time I boot the system it goes right to that black screen posting all the error messages or output in white text. I never get a purple Ubuntu splash, so from what I can tell after reading this wiki article: https://wiki.ubuntu.com/X/Troubleshooting/BlankScreen That means that after the kernel is selected, it is unable to correctly implement the settings it needs. If the purple splash never shows, the frame buffer was never set correctly right? This leads me to believe that it could be a kernel issue? The wiki suggested to try and pinpoint the issue by rolling back kernels until I find one that works. Is this my best option? I think I'm going to give it a try anyways and will let everyone know if I am able to solve the issue this way. I have since done a few reinstalls and some trouble-shooting including a couple hours scouring the net for anyone with any kind of similar issue. Most of the issues I could find involved getting a black screen after login and none of them said anything about any information output on this black screen. My reinstalls have taught me that there is no issue updating, but as soon as I run sudo apt-get upgrade my system goes to the black screen and every time I boot it up it does the same thing. The only way to fix is by reinstall. I never get any ability to log in. After a hard power off to the laptop (because I cannot use ctrl+alt+del to reboot) when it boots again it goes to the grub boot menu and I can select between regular boot, recovery mode and the two memtest options. I never tried the memtest options but the other two both lead to the same black screen. Some people having a black/blank screen issue claim to have fixed it by using 12.10 or 13.04 but I believe they were having a different issue where they got a black/blank screen after logging in. I think I will still give these images a try, but mostly figured I would just wait another day or two for 13.10. Other things I figured I would try from the following three articles: After logging in, there's a black screen and my cursor, nothing else! in Ubuntu 12.10 Black Screen on Login After Upgrading to 12.04 I can't get to the login screen include opening a terminal using ctrl+alt+f1 and trying a variety of reseting unity, x settings, lightdm (or switching to gdm); but I doubt this will work or that I will even be able to access a terminal. I'm pretty sure the whole system is stuck after it loads the last line on the black screen. I will try these things and post more information when I have. Hopefully someone has an idea in the meantime and I will keep checking back trying to find a solution. Thank you. Here are 3 different pictures of the error message. I had to take with my phone: http://ubuntuone.com/album/0TBBkxmVajJIQQtoN9mVdN

  Read the article

• Some Early Considerations

  - by Chris Massey

  Following on from my previous post, I want to say "thank you" to everyone who has got in touch and got involved – you are pioneers! An update on where we are right now: paper prototypes v1 To be more specific, we’ve picked two of the ideas that seem to have more pros than cons, turned them into Balsamiq mockups, and are getting them fleshed out with realistic content. We’ll initially make these available to the aforementioned pioneers (thank you again), roll in the feedback, and then open up to get more data on what works and what doesn’t. If you’ve got any questions about this (or what we’re working on right now), feel free to ask me in the comments below. I’ve had a few people express an interest in the process we’re going through, and I’m more than happy to share details more frequently as we go along – not least because you, dear reader, will help us stay on target and create something Good. To start with, here’s a quick flashback to bring you all up to speed. A Brief Retrospective As you may already know, we’re creating a new publishing asset specifically focused on providing great content for web developers. We don’t yet know exactly what this thing will look like, or exactly how it will work, but we know we want to create something that is useful different. For my part, I’m seriously excited at the prospect of building a genuinely digital publishing system (as opposed to what most publishing is these days, which is print-style publishing which just happens to be on the web). The main challenge at this point is working out our build-measure-assess loop to speed up our experimental turn-around, and that’ll get better as we run more trials. Of course, there are a few things we’ve been pondering at this early conceptual stage: Do we publishing about heterogeneous technology stacks from day 1, or do we start with ASP.NET (which we’re familiar with) & branch out later? There are challenges with either approach. What publishing "modes" are already being well-handled? For example, the likes of Pluralsight, TekPub, and Treehouse have pretty much nailed video training (debate about price, if you like), and unless we think we can do it faster / better / cheaper (unlikely, for the record), we should leave them to it. Where should we base whatever we create? Should we create a completely new asset under a new name, graft something onto Simple-Talk (like the labs), or just build something directly into Simple-Talk? It sounds trivial, but it does have at least some impact on infrastructure and what how we manage the different types of content we (will) have. Are there any obvious problems or niches that we think could address really well, or should we just throw ideas out and see what readers respond to? What kind of users do we want to provide for? This actually deserves a little bit of unpacking… Why are you here? We currently divide readers into (broadly) the categories: Category 1: I know nothing about X, and I’d like to learn about it. Category 2: I know something about X, but I’d like to learn how to do something specific with it. Category 3: Ah man, I have a problem with X, and I need to fix it now. Now that I think about it, I might also include a 4th class of reader: Category 4: I’m looking for something interesting to engage my brain. These are clearly task-based categorizations, and depending on which task you’re performing when you arrive here, you’re going to need different types of content, or will have specific discovery needs. One of the questions that’s at the back of my mind whenever I consider a new idea is “How many of the categories will this satisfy?” As an example, typical video training is very well suited to categories 1, 2, and 4. StackOverflow is very well suited to category 3, and serves as a sign-posting system to the rest. Clearly it’s not necessary to satisfy every category need to be useful and popular, but being aware of what behavior readers might be exhibiting when they arrive will help us tune our ideas appropriately. < / Flashback > We don’t have clean answers to most of these considerations – they’re things we’re aware of, and each idea we look at is going to be best suited to a different mix of the options I’ve described. Our first experimental loop will be coming full circle in the next few days, so we should start to see how the different possibilities vary between ideas. Free to chime in with questions and suggestions about anything I’ve just brain-dumped, or at any stage as we go along. If you see anything that intrigued or enrages you, or just have an idea you’d like to share, I’d love to hear from you.

  Read the article

< Previous Page | 2276 2277 2278 2279 2280 2281 2282 2283 2284 2285 2286 2287  | Next Page >