Search Results

Search found 37931 results on 1518 pages for 'computer case'.

Page 233/1518 | < Previous Page | 229 230 231 232 233 234 235 236 237 238 239 240  | Next Page >

  • How to setup ATI Mobility Radeon HD 4650?

    - by Thi An
    I'm currently using Ubuntu 12.04 64bit. After installing ATI/AMD proprietary FGLRX graphics drivers via Additional Drivers, I checked the status of my VGA card using lspci -v. Here's the output: 02:00.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI M96 [Mobility Radeon HD 4650] (prog-if 00 [VGA controller]) Subsystem: Dell Device 0456 Flags: bus master, fast devsel, latency 0, IRQ 46 Memory at d0000000 (32-bit, prefetchable) [size=256M] I/O ports at 2000 [size=256] Memory at cfef0000 (32-bit, non-prefetchable) [size=64K] [virtual] Expansion ROM at cfe00000 [disabled] [size=128K] Capabilities: Kernel driver in use: fglrx_pci Kernel modules: fglrx, radeon As mentioned in the title, my VGA card is 1GB and yet my computer only recognizes 256MB. My question is: "How to make my computer fully recognize the capacity of my ATI Mobility Radeon HD 4650 (1GB)?"

    Read the article

  • Weekend Project: Make Your Own Ferromagnetic Fluid

    - by Jason Fitzpatrick
    Experiments this simple and fun give you no reason to leave all science-based goofing off to the professionals: whip up a beaker of ferromagnetic fluid to capture magnetic waves in motion. The premise is simple: by combing a viscous liquid (in this case vegetable oil) with a magnetic powder (in this case MICR copy toner) and introducing a strong magnetic source (such as neodymium rare earth magnets), you can actually see the magnetic waves in physical space. It’s like the old magnetic filings on the table top trick, but in 3D. Check out the video above to see how you can mix up a batch of your own. How to Make Magnetic Fluid [YouTube] What Is the Purpose of the “Do Not Cover This Hole” Hole on Hard Drives? How To Log Into The Desktop, Add a Start Menu, and Disable Hot Corners in Windows 8 HTG Explains: Why You Shouldn’t Use a Task Killer On Android

    Read the article

  • Freezes for unknown reasons, causing fan to go crazy on a Portege laptop

    - by Sünnje
    I have recently installed Natty on a new Toshiba Portege laptop. I find it extremely irritating that the system freezes frequently, about every other time I use the computer. Then the fan goes crazy and I have to force-shutdown. It seems to happen no matter what I do; I encountered this problem when using Firefox, LibreOffice, Adobe Reader - probably when using only terminals too, but I'm not certain. It may be fan-related, because the computer seems to get heated up compared compared to earlier, but I am not sure about that. Any ideas why this could be happening?

    Read the article

  • Desktop Fun: Runic Style Fonts

    - by Asian Angel
    Most of the time regular fonts are just what you need for documents, invitations, or adding text to images. But what if you are in the mood for something unusual or unique to add that perfect touch? If you like older runic style writing, then enjoy finding some new favorites for your collection with our Runic Style Fonts collection. Temple photo by ShinyShiny. Note: To manage the fonts on your Windows 7, Vista, & XP systems see our article here. The Runic Style Fonts Sable Download Worn Manuscript Download JSL Ancient Download Antropos Download Cave Gyrl Download The Roman Runes Alliance Download Ancient Geek Download Troll Download Runish Quill MK *includes two font types Download DS RUNEnglish 2 Download Runes Written *includes two font types Download Wolves And Ravens Download Art Greco Download Dalek Download Glagolitic AOE Download Linear B Download Cartouche Download Greywolf Glyphs *includes 62 individual characters Note: This group represents A – Z in all capital letters. Note: This group represents A – Z in all lower case letters. Note: This group represents the numbers 0 – 9. Download Africain *includes 62 individual characters Note: This group represents A – Z in all capital letters. Note: This group represents A – Z in all lower case letters. Note: This group represents the numbers 0 – 9. Download Cave Writings *includes 52 individual characters Note: This group represents A – Z in all capital letters. Note: This group represents A – Z in all lower case letters. Download For more great ways to customize your computer be certain to look through our Desktop Fun section. Latest Features How-To Geek ETC HTG Projects: How to Create Your Own Custom Papercraft Toy How to Combine Rescue Disks to Create the Ultimate Windows Repair Disk What is Camera Raw, and Why Would a Professional Prefer it to JPG? The How-To Geek Guide to Audio Editing: The Basics How To Boot 10 Different Live CDs From 1 USB Flash Drive The 20 Best How-To Geek Linux Articles of 2010 Five Sleek Audi R8 Car Themes for Chrome and Iron MS Notepad Replacement Metapad Returns with a New Beta Version Spybot Search and Destroy Now Available as a Portable App (PortableApps.com) ShapeShifter: What Are Dreams? [Video] This Computer Runs on Geek Power Wallpaper Bones, Clocks, and Counters; A Look at the First 35,000 Years of Computing

    Read the article

  • How to stop programs on starting from returning to log in screen?

    - by Bruce McKean
    I'm not a computer nerd but have been able to fix Ubuntu/Linux problems in the pass two years with a Google search but this on has me stumped. I upgraded to 12.04 about thirty days ago and all was well except that every time I tried to load KeePassX it would go to the login screen. I installed KeePass2 and all seemed to work. Last week I tried to load Bibble5 (Raw photo editor) and it would try to load and then back to the login screen. After a few days I gave up and downloaded Corel After Shot Pro (Corel's now owns Bibble5) and it has the same problem. Could someone please head me into the steps I need to follow to find out what is the cause. I'm interested in learning more about the Linux system how to correct any future problems thanks in advance – Bruce -Computer- Processor : 8x Intel(R) Core(TM) i7-2600 CPU @ 3.40GHz Memory : 8155MB (1092MB used) Operating System : Ubuntu 12.04 LTS OpenGL Renderer : GeForce GT 520/PCIe/SSE2

    Read the article

  • Filtering List Data with a jQuery-searchFilter Plugin

    - by Rick Strahl
    When dealing with list based data on HTML forms, filtering that data down based on a search text expression is an extremely useful feature. We’re used to search boxes on just about anything these days and HTML forms should be no different. In this post I’ll describe how you can easily filter a list down to just the elements that match text typed into a search box. It’s a pretty simple task and it’s super easy to do, but I get a surprising number of comments from developers I work with who are surprised how easy it is to hook up this sort of behavior, that I thought it’s worth a blog post. But Angular does that out of the Box, right? These days it seems everybody is raving about Angular and the rich SPA features it provides. One of the cool features of Angular is the ability to do drop dead simple filters where you can specify a filter expression as part of a looping construct and automatically have that filter applied so that only items that match the filter show. I think Angular has single handedly elevated search filters to first rate, front-row status because it’s so easy. I love using Angular myself, but Angular is not a generic solution to problems like this. For one thing, using Angular requires you to render the list data with Angular – if you have data that is server rendered or static, then Angular doesn’t work. Not all applications are client side rendered SPAs – not by a long shot, and nor do all applications need to become SPAs. Long story short, it’s pretty easy to achieve text filtering effects using jQuery (or plain JavaScript for that matter) with just a little bit of work. Let’s take a look at an example. Why Filter? Client side filtering is a very useful tool that can make it drastically easier to sift through data displayed in client side lists. In my applications I like to display scrollable lists that contain a reasonably large amount of data, rather than the classic paging style displays which tend to be painful to use. So I often display 50 or so items per ‘page’ and it’s extremely useful to be able to filter this list down. Here’s an example in my Time Trakker application where I can quickly glance at various common views of my time entries. I can see Recent Entries, Unbilled Entries, Open Entries etc and filter those down by individual customers and so forth. Each of these lists results tends to be a few pages worth of scrollable content. The following screen shot shows a filtered view of Recent Entries that match the search keyword of CellPage: As you can see in this animated GIF, the filter is applied as you type, displaying only entries that match the text anywhere inside of the text of each of the list items. This is an immediately useful feature for just about any list display and adds significant value. A few lines of jQuery The good news is that this is trivially simple using jQuery. To get an idea what this looks like, here’s the relevant page layout showing only the search box and the list layout:<div id="divItemWrapper"> <div class="time-entry"> <div class="time-entry-right"> May 11, 2014 - 7:20pm<br /> <span style='color:steelblue'>0h:40min</span><br /> <a id="btnDeleteButton" href="#" class="hoverbutton" data-id="16825"> <img src="images/remove.gif" /> </a> </div> <div class="punchedoutimg"></div> <b><a href='/TimeTrakkerWeb/punchout/16825'>Project Housekeeping</a></b><br /> <small><i>Sawgrass</i></small> </div> ... more items here </div> So we have a searchbox txtSearchPage and a bunch of DIV elements with a .time-entry CSS class attached that makes up the list of items displayed. To hook up the search filter with jQuery is merely a matter of a few lines of jQuery code hooked to the .keyup() event handler: <script type="text/javascript"> $("#txtSearchPage").keyup(function() { var search = $(this).val(); $(".time-entry").show(); if (search) $(".time-entry").not(":contains(" + search + ")").hide(); }); </script> The idea here is pretty simple: You capture the keystroke in the search box and capture the search text. Using that search text you first make all items visible and then hide all the items that don’t match. Since DOM changes are applied after a method finishes execution in JavaScript, the show and hide operations are effectively batched up and so the view changes only to the final list rather than flashing the whole list and then removing items on a slow machine. You get the desired effect of the list showing the items in question. Case Insensitive Filtering But there is one problem with the solution above: The jQuery :contains filter is case sensitive, so your search text has to match expressions explicitly which is a bit cumbersome when typing. In the screen capture above I actually cheated – I used a custom filter that provides case insensitive contains behavior. jQuery makes it really easy to create custom query filters, and so I created one called containsNoCase. Here’s the implementation of this custom filter:$.expr[":"].containsNoCase = function(el, i, m) { var search = m[3]; if (!search) return false; return new RegExp(search, "i").test($(el).text()); }; This filter can be added anywhere where page level JavaScript runs – in page script or a seperately loaded .js file.  The filter basically extends jQuery with a : expression. Filters get passed a tokenized array that contains the expression. In this case the m[3] contains the search text from inside of the brackets. A filter basically looks at the active element that is passed in and then can return true or false to determine whether the item should be matched. Here I check a regular expression that looks for the search text in the element’s text. So the code for the filter now changes to:$(".time-entry").not(":containsNoCase(" + search + ")").hide(); And voila – you now have a case insensitive search.You can play around with another simpler example using this Plunkr:http://plnkr.co/edit/hDprZ3IlC6uzwFJtgHJh?p=preview Wrapping it up in a jQuery Plug-in To make this even easier to use and so that you can more easily remember how to use this search type filter, we can wrap this logic into a small jQuery plug-in:(function($, undefined) { $.expr[":"].containsNoCase = function(el, i, m) { var search = m[3]; if (!search) return false; return new RegExp(search, "i").test($(el).text()); }; $.fn.searchFilter = function(options) { var opt = $.extend({ // target selector targetSelector: "", // number of characters before search is applied charCount: 1 }, options); return this.each(function() { var $el = $(this); $el.keyup(function() { var search = $(this).val(); var $target = $(opt.targetSelector); $target.show(); if (search && search.length >= opt.charCount) $target.not(":containsNoCase(" + search + ")").hide(); }); }); }; })(jQuery); To use this plug-in now becomes a one liner:$("#txtSearchPagePlugin").searchFilter({ targetSelector: ".time-entry", charCount: 2}) You attach the .searchFilter() plug-in to the text box you are searching and specify a targetSelector that is to be filtered. Optionally you can specify a character count at which the filter kicks in since it’s kind of useless to filter at a single character typically. Summary This is s a very easy solution to a cool user interface feature your users will thank you for. Search filtering is a simple but highly effective user interface feature, and as you’ve seen in this post it’s very simple to create this behavior with just a few lines of jQuery code. While all the cool kids are doing Angular these days, jQuery is still useful in many applications that don’t embrace the ‘everything generated in JavaScript’ paradigm. I hope this jQuery plug-in or just the raw jQuery will be useful to some of you… Resources Example on Plunker© Rick Strahl, West Wind Technologies, 2005-2014Posted in jQuery  HTML5  JavaScript   Tweet !function(d,s,id){var js,fjs=d.getElementsByTagName(s)[0];if(!d.getElementById(id)){js=d.createElement(s);js.id=id;js.src="//platform.twitter.com/widgets.js";fjs.parentNode.insertBefore(js,fjs);}}(document,"script","twitter-wjs"); (function() { var po = document.createElement('script'); po.type = 'text/javascript'; po.async = true; po.src = 'https://apis.google.com/js/plusone.js'; var s = document.getElementsByTagName('script')[0]; s.parentNode.insertBefore(po, s); })();

    Read the article

  • BPM 11g - Dynamic Task Assignment with Multi-level Organization Units

    - by Mark Foster
    I've seen several requirements to have a more granular level of task assignment in BPM 11g based on some value in the data passed to the process. Parametric Roles is normally the first port of call to try to satisfy this requirement, but in this blog we will show how a lot of use-cases can be satisfied by the easier to implement and flexible Organization Unit. The Use-Case Task assignment is to an approval group containing several users. At runtime, a location value in the input data determines which of the particular users the task is ultimately assigned to. In this case we use the Demo Community referenced in the SOA Admin Guide, and specifically the "LoanAnalyticGroup" which contains three users; "szweig", "mmitch" & "fkafka". In our scenario we would like to assign a task to "szweig" if the input data specifies that the location is "JapanCentral", to "fkafka" if the location is "JapanNorth" and to "mmitch" if "JapanSouth", and to all of them if the location is "Japan" i.e....   The Process Simple one human task process.... In the output data association of the "Start" activity we need to set the value of the "Organization Unit" predefined variable based on the input data (note that the  predefined variables can only be set on output data associations)....  ...and in the output data association of the human activity we will reset the "Organization Unit" to empty, always good practice to ensure that the Organization Unit will not be used for any subsequent human activities for which we do not require it.... Set Up the Organization Unit  Log in to the BPM Workspace with an administrator user (weblogic/welcome1 in our case) and choose the "Administration" option. Within "Roles" assign the "ProcessOwner" swim-lane for our process to "LoanAnalyticGroup".... Within "Organization Units" we can model our organization.... "Root Organization Unit" as "Japan" and "Child Organization Unit" as "Central", "South" & "North" as shown. As described previously, add user "szweig" to "Central", "mmitch" to "South" and "fkafka" to "North"....   Test the Process Invalid Data  First let us test with invalid data in the input to see what the consequences are, here we use "X" as input.... ...and looking at the instance we can see it has errored.... Organization Unit Root Level Assignment  Now let us see what happens if we have "Japan" in the input data.... ...looking in the "flow trace" we can see that the task has been assigned....  ... but who has the task been assigned to ? Let us look in the BPM Workspace for user "szweig"....  ...and for "mmitch"....  ... and for "fkafka"....  ...so we can see that with an Organization Unit at "Root" level we have successfully assigned the task to all users. Organization Unit Child Level Assignment  Now let us test with "Japan/North" in the input data.... ...and looking in "fkafka" workspace we see the task has been assigned, remember, he was associated with "JapanNorth"....   ... but what about the workspace of "szweig"....  ...no tasks assigned, neither has "mmitch", just as we expected. Summary  We have seen in this blog how to easily implement multi-level dynamic task routing using Organization Units, a common use-case and a simpler solution than Parametric Roles. 

    Read the article

  • What benefits does a game design degree have for a hobby game programmer?

    - by sm4
    I am interested in studying game design, not because I want a job in the games industry, but because I am interested in the subject itself. I read the following questions, but they mostly deal with the effects on your career in game industry. Should I consider a graduate degree in game development? Game Development Degree vs Computer Science Degree First I thought a game development degree could be beneficial. But from the websites of colleges that offer such degrees, I feel like its more about basic programming with examples from games. This college offers game design degrees, for example. My question is, can I benefit from such a degree when I already have a degree in Computer Science, I already know programming, I'm already developing a game and finally, I have this site to help me when I get stuck?

    Read the article

  • Oracle Keeps Growing Partner Certifications with Addition of McAfee

    - by Ted Davis
    Viruses stink. Whether it’s the common cold virus, Goatpox virus – yes it exists -- or a computer virus, you name it, viruses stink. When it comes to our computer server infrastructure we all want to make sure our servers are secure from any malware out there. Additionally, installation of anti-virus software is a requirement by many governments and for many enterprises both large and small. Because of the growth of Oracle Linux in their customer base, McAfee recently certified their “McAfee VirusScan Enterprise for Linux” on Oracle Linux.  It delivers always-on, real-time anti-virus protection for Linux environments. Its unique, Linux-based on-access scanner constantly monitors the system for potential attacks. While there have been few viruses found on Linux, you can now feel secure running Oracle Linux in your infrastructure with McAfee on top. We are happy to introduce McAfee into the Oracle Linux family of certified applications. 

    Read the article

  • The Joy Of Hex

    - by Jim Giercyk
    While working on a mainframe integration project, it occurred to me that some basic computer concepts are slipping into obscurity. For example, just about anyone can tell you that a 64-bit processor is faster than a 32-bit processer. A grade school child could tell you that a computer “speaks” in ‘1’s and ‘0’s. Some people can even tell you that there are 8 bits in a byte. However, I have found that even the most seasoned developers often can’t explain the theory behind those statements. That is not a knock on programmers; in the age of IntelliSense, what reason do we have to work with data at the bit level? Many computer theory classes treat bit-level programming as a thing of the past, no longer necessary now that storage space is plentiful. The trouble with that mindset is that the world is full of legacy systems that run programs written in the 1970’s.  Today our jobs require us to extract data from those systems, regardless of the format, and that often involves low-level programming. Because it seems knowledge of the low-level concepts is waning in recent times, I thought a review would be in order.       CHARACTER: See Spot Run HEX: 53 65 65 20 53 70 6F 74 20 52 75 6E DECIMAL: 83 101 101 32 83 112 111 116 32 82 117 110 BINARY: 01010011 01100101 01100101 00100000 01010011 01110000 01101111 01110100 00100000 01010010 01110101 01101110 In this example, I have broken down the words “See Spot Run” to a level computers can understand – machine language.     CHARACTER:  The character level is what is rendered by the computer.  A “Character Set” or “Code Page” contains 256 characters, both printable and unprintable.  Each character represents 1 BYTE of data.  For example, the character string “See Spot Run” is 12 Bytes long, exclusive of the quotation marks.  Remember, a SPACE is an unprintable character, but it still requires a byte.  In the example I have used the default Windows character set, ASCII, which you can see here:  http://www.asciitable.com/ HEX:  Hex is short for hexadecimal, or Base 16.  Humans are comfortable thinking in base ten, perhaps because they have 10 fingers and 10 toes; fingers and toes are called digits, so it’s not much of a stretch.  Computers think in Base 16, with numeric values ranging from zero to fifteen, or 0 – F.  Each decimal place has a possible 16 values as opposed to a possible 10 values in base 10.  Therefore, the number 10 in Hex is equal to the number 16 in Decimal.  DECIMAL:  The Decimal conversion is strictly for us humans to use for calculations and conversions.  It is much easier for us humans to calculate that [30 – 10 = 20] in decimal than it is for us to calculate [1E – A = 14] in Hex.  In the old days, an error in a program could be found by determining the displacement from the entry point of a module.  Since those values were dumped from the computers head, they were in hex. A programmer needed to convert them to decimal, do the equation and convert back to hex.  This gets into relative and absolute addressing, a topic for another day.  BINARY:  Binary, or machine code, is where any value can be expressed in 1s and 0s.  It is really Base 2, because each decimal place can have a possibility of only 2 characters, a 1 or a 0.  In Binary, the number 10 is equal to the number 2 in decimal. Why only 1s and 0s?  Very simply, computers are made up of lots and lots of transistors which at any given moment can be ON ( 1 ) or OFF ( 0 ).  Each transistor is a bit, and the order that the transistors fire (or not fire) is what distinguishes one value from  another in the computers head (or CPU).  Consider 32 bit vs 64 bit processing…..a 64 bit processor has the capability to read 64 transistors at a time.  A 32 bit processor can only read half as many at a time, so in theory the 64 bit processor should be much faster.  There are many more factors involved in CPU performance, but that is the fundamental difference.    DECIMAL HEX BINARY 0 0 0000 1 1 0001 2 2 0010 3 3 0011 4 4 0100 5 5 0101 6 6 0110 7 7 0111 8 8 1000 9 9 1001 10 A 1010 11 B 1011 12 C 1100 13 D 1101 14 E 1110 15 F 1111   Remember that each character is a BYTE, there are 2 HEX characters in a byte (called nibbles) and 8 BITS in a byte.  I hope you enjoyed reading about the theory of data processing.  This is just a high-level explanation, and there is much more to be learned.  It is safe to say that, no matter how advanced our programming languages and visual studios become, they are nothing more than a way to interpret bits and bytes.  There is nothing like the joy of hex to get the mind racing.

    Read the article

  • Change permission to mount disk at rdesktop

    - by Tal
    I have ubuntu 10.04 and have installed rdesktop 1.7. I have run these commands: sudo umount /media/Tal sudo mount -t ntfs-3g -o uid=1000,gid=1000,umask=0000 /dev/sdb1 /media/Tal rdesktop -0 -r sound:local -f -u administrator -r clipboard:PRIMARYCLIPBOARD -r disk:tal=/media/Tal myip Tal is external hard drive connecting at USB in ntfs file system. I connect to windows 7 I see the hard drive in computer and I can access to files and create new files and folders, But when I try to copy a new file to a folder he show me an error message: You need permission perform this action Your require permission from computer's administrator to make changes to this folder Tal on my computername Disk from Remote Desktop Connection. I try chmod and chown too but I read I linux forum when it ntfs is no use. Some one can help me with my problem?

    Read the article

  • BizTalk and SQL: Alternatives to the SQL receive adapter. Using Msmq to receive SQL data

    - by Leonid Ganeline
    If we have to get data from the SQL database, the standard way is to use a receive port with SQL adapter. SQL receive adapter is a solicit-response adapter. It periodically polls the SQL database with queries. That’s only way it can work. Sometimes it is undesirable. With new WCF-SQL adapter we can use the lightweight approach but still with the same principle, the WCF-SQL adapter periodically solicits the database with queries to check for the new records. Imagine the situation when the new records can appear in very broad time limits, some - in a second interval, others - in the several minutes interval. Our requirement is to process the new records ASAP. That means the polling interval should be near the shortest interval between the new records, a second interval. As a result the most of the poll queries would return nothing and would load the database without good reason. If the database is working under heavy payload, it is very undesirable. Do we have other choices? Sure. We can change the polling to the “eventing”. The good news is the SQL server could issue the event in case of new records with triggers. Got a new record –the trigger event is fired. No new records – no the trigger events – no excessive load to the database. The bad news is the SQL Server doesn’t have intrinsic methods to send the event data outside. For example, we would rather use the adapters that do listen for the data and do not solicit. There are several such adapters-listeners as File, Ftp, SOAP, WCF, and Msmq. But the SQL Server doesn’t have methods to create and save files, to consume the Web-services, to create and send messages in the queue, does it? Can we use the File, FTP, Msmq, WCF adapters to get data from SQL code? Yes, we can. The SQL Server 2005 and 2008 have the possibility to use .NET code inside SQL code. See the SQL Integration. How it works for the Msmq, for example: ·         New record is created, trigger is fired ·         Trigger calls the CLR stored procedure and passes the message parameters to it ·         The CLR stored procedure creates message and sends it to the outgoing queue in the SQL Server computer. ·         Msmq service transfers message to the queue in the BizTalk Server computer. ·         WCF-NetMsmq adapter receives the message from this queue. For the File adapter the idea is the same, the CLR stored procedure creates and stores the file with message, and then the File adapter picks up this file. Using WCF-NetMsmq adapter to get data from SQL I am describing the full set of the deployment and development steps for the case with the WCF-NetMsmq adapter. Development: 1.       Create the .NET code: project, class and method to create and send the message to the MSMQ queue. 2.       Create the SQL code in triggers to call the .NET code. Installation and Deployment: 1.       SQL Server: a.       Register the CLR assembly with .NET (CLR) code b.      Install the MSMQ Services 2.       BizTalk Server: a.       Install the MSMQ Services b.      Create the MSMQ queue c.       Create the WCF-NetMsmq receive port. The detailed description is below. Code .NET code … using System.Xml; using System.Xml.Linq; using System.Xml.Serialization;   //namespace MyCompany.MySolution.MyProject – doesn’t work. The assembly name is MyCompany.MySolution.MyProject // I gave up with the compound namespace. Seems the CLR Integration cannot work with it L. Maybe I’m wrong.     public class Event     {         static public XElement CreateMsg(int par1, int par2, int par3)         {             XNamespace ns = "http://schemas.microsoft.com/Sql/2008/05/TypedPolling/my_storedProc";             XElement xdoc =                 new XElement(ns + "TypedPolling",                     new XElement(ns + "TypedPollingResultSet0",                         new XElement(ns + "TypedPollingResultSet0",                             new XElement(ns + "par1", par1),                             new XElement(ns + "par2", par2),                             new XElement(ns + "par3", par3),                         )                     )                 );             return xdoc;         }     }   //////////////////////////////////////////////////////////////////////// … using System.ServiceModel; using System.ServiceModel.Channels; using System.Transactions; using System.Data; using System.Data.Sql; using System.Data.SqlTypes;   public class MsmqHelper {     [Microsoft.SqlServer.Server.SqlProcedure]     // msmqAddress as "net.msmq://localhost/private/myapp.myqueue";     public static void SendMsg(string msmqAddress, string action, int par1, int par2, int par3)     {         using (TransactionScope scope = new TransactionScope(TransactionScopeOption.Suppress))         {             NetMsmqBinding binding = new NetMsmqBinding(NetMsmqSecurityMode.None);             binding.ExactlyOnce = true;             EndpointAddress address = new EndpointAddress(msmqAddress);               using (ChannelFactory<IOutputChannel> factory = new ChannelFactory<IOutputChannel>(binding, address))             {                 IOutputChannel channel = factory.CreateChannel();                 try                 {                     XElement xe = Event.CreateMsg(par1, par2, par3);                     XmlReader xr = xe.CreateReader();                     Message msg = Message.CreateMessage(MessageVersion.Default, action, xr);                     channel.Send(msg);                     //SqlContext.Pipe.Send(…); // to test                 }                 catch (Exception ex)                 { …                 }             }             scope.Complete();         }     }   SQL code in triggers   -- sp_SendMsg was registered as a name of the MsmqHelper.SendMsg() EXEC sp_SendMsg'net.msmq://biztalk_server_name/private/myapp.myqueue', 'Create', @par1, @par2, @par3   Installation and Deployment On the SQL Server Registering the CLR assembly 1.       Prerequisites: .NET 3.5 SP1 Framework. It could be the issue for the production SQL Server! 2.       For more information, please, see the link http://nielsb.wordpress.com/sqlclrwcf/ 3.       Copy files: >copy “\Windows\Microsoft.net\Framework\v3.0\Windows Communication Foundation\Microsoft.Transactions.Bridge.dll” “\Program Files\Reference Assemblies\Microsoft\Framework\v3.0 \Microsoft.Transactions.Bridge.dll” If your machine is a 64-bit, run two commands: >copy “\Windows\Microsoft.net\Framework\v3.0\Windows Communication Foundation\Microsoft.Transactions.Bridge.dll” “\Program Files (x86)\Reference Assemblies\Microsoft\Framework\v3.0 \Microsoft.Transactions.Bridge.dll” >copy “\Windows\Microsoft.net\Framework64\v3.0\Windows Communication Foundation\Microsoft.Transactions.Bridge.dll” “\Program Files\Reference Assemblies\Microsoft\Framework\v3.0 \Microsoft.Transactions.Bridge.dll” 4.       Execute the SQL code to register the .NET assemblies: -- For x64 OS: CREATE ASSEMBLY SMdiagnostics AUTHORIZATION dbo FROM 'C:\Windows\Microsoft.NET\Framework\v3.0\Windows Communication Foundation\SMdiagnostics.dll' WITH permission_set = unsafe CREATE ASSEMBLY [System.Web] AUTHORIZATION dbo FROM 'C:\Windows\Microsoft.NET\Framework64\v2.0.50727\System.Web.dll' WITH permission_set = unsafe CREATE ASSEMBLY [System.Messaging] AUTHORIZATION dbo FROM 'C:\Windows\Microsoft.NET\Framework\v2.0.50727\System.Messaging.dll' WITH permission_set = unsafe CREATE ASSEMBLY [System.ServiceModel] AUTHORIZATION dbo FROM 'C:\Program Files (x86)\Reference Assemblies\Microsoft\Framework\v3.0\System.ServiceModel.dll' WITH permission_set = unsafe CREATE ASSEMBLY [System.Xml.Linq] AUTHORIZATION dbo FROM 'C:\Program Files\Reference Assemblies\Microsoft\Framework\v3.5\System.Xml.Linq.dll' WITH permission_set = unsafe   -- For x32 OS: --CREATE ASSEMBLY SMdiagnostics AUTHORIZATION dbo FROM 'C:\Windows\Microsoft.NET\Framework\v3.0\Windows Communication Foundation\SMdiagnostics.dll' WITH permission_set = unsafe --CREATE ASSEMBLY [System.Web] AUTHORIZATION dbo FROM 'C:\Windows\Microsoft.NET\Framework\v2.0.50727\System.Web.dll' WITH permission_set = unsafe --CREATE ASSEMBLY [System.Messaging] AUTHORIZATION dbo FROM 'C:\Windows\Microsoft.NET\Framework\v2.0.50727\System.Messaging.dll' WITH permission_set = unsafe --CREATE ASSEMBLY [System.ServiceModel] AUTHORIZATION dbo FROM 'C:\Program Files\Reference Assemblies\Microsoft\Framework\v3.0\System.ServiceModel.dll' WITH permission_set = unsafe 5.       Register the assembly with the external stored procedure: CREATE ASSEMBLY [HelperClass] AUTHORIZATION dbo FROM ’<FilePath>MyCompany.MySolution.MyProject.dll' WITH permission_set = unsafe where the <FilePath> - the path of the file on this machine! 6. Create the external stored procedure CREATE PROCEDURE sp_SendMsg (        @msmqAddress nvarchar(100),        @Action NVARCHAR(50),        @par1 int,        @par2 int,        @par3 int ) AS EXTERNAL NAME HelperClear.MsmqHelper.SendMsg   Installing the MSMQ Services 1.       Check if the MSMQ service is NOT installed. To check:  Start / Administrative Tools / Computer Management, on the left pane open the “Services and Applications”, search to the “Message Queuing”. If you cannot see it, follow next steps. 2.       Start / Control Panel / Programs and Features 3.       Click “Turn Windows Features on or off” 4.       Click Features, click “Add Features” 5.       Scroll down the feature list; open the “Message Queuing” / “Message Queuing Services”; and check the “Message Queuing Server” option  6.       Click Next; Click Install; wait to the successful finish of the installation Creating the MSMQ queue We don’t need to create the queue on the “sender” side. On the BizTalk Server Installing the MSMQ Services The same is as for the SQL Server. Creating the MSMQ queue 1.       Start / Administrative Tools / Computer Management, on the left pane open the “Services and Applications”, open the “Message Queuing”, and open the “Private Queues”. 2.       Right-click the “Private Queues”; choose New; choose “Private Queue”. 3.       Type the Queue name as ’myapp.myqueue'; check the “Transactional” option. Creating the WCF-NetMsmq receive port I will not go through this step in all details. It is straightforward. URI for this receive location should be 'net.msmq://localhost/private/myapp.myqueue'. Notes ·         The biggest problem is usually on the step the “Registering the CLR assembly”. It is hard to predict where are the assemblies from the assembly list, what version should be used, x86 or x64. It is pity of such “rude” integration of the SQL with .NET. ·         In couple cases the new WCF-NetMsmq port was not able to work with the queue. Try to replace the WCF- NetMsmq port with the WCF-Custom port with netMsmqBinding. It was working fine for me. ·         To test how messages go through the queue you can turn on the Journal /Enabled option for the queue. I used the QueueExplorer utility to look to the messages in Journal. The Computer Management can also show the messages but it shows only small part of the message body and in the weird format. The QueueExplorer can do the better job; it shows the whole body and Xml messages are in good color format.

    Read the article

  • Can't boot without Flash Drive plugged in

    - by vlad
    (Sorry for my bad English) I had Ubuntu 12.04 Beta installed on my computer. When 12.04 was finally released, I made a bootable USB Flash Drive using Startup Disk Creator. Then I decided to check if this drive works properly and to reinstall the system on my desktop. I must add, my desktop behaves a bit strange when it comes to bootable USB's, it recognizes them as HDD. In BIOS I changed priority of boot so USB Flash Drive (recognized as HDD) was first. Successfully booted, I installed Ubuntu. Everything worked fine, but... Now I cannot boot from my real HDD. Every time I want to boot, I put the USB Flash Drive into my computer, boot, safely remove it and everything works. What have I to do, to repair boot? Thank you for your time!

    Read the article

  • How to encrypt php folder under /var/www?

    - by sirchaos
    I need to encrypt the folder /var/www/test. The folder contains PHP files. The goal it to prevent any user to read the php content AND if the HD is mounted on another computer, the /var/www/test should be encrypted AND if computer booted up without any user logged I would like anyone to be able to access data in /var/www/tests. What is the correct approach for this? I've tried "ecryptfs-setup-private" as advised in How to encrypt /var/www? yet it didn't work for me. I've might missed something - I've tested the folders while booting with ubuntu 12.04 installation disk and mounted the drive, than I was able to access /var/www/test content.. yet this is what I want to prevent. The gnome-encfs isn't the way to go since its decryption happens when users logs on to the system & I would like the system to be working after power failure etc' without any one logged in. Please advice.

    Read the article

  • How do I get wireless to work on a Dell Mini 1018 with Realtek RTL 8188CE Network Adapter?

    - by Laurence Nagel
    My Dell Mini 1018 used to work fine with Ubuntu 12.04 with no problems connecting with the wireless card. Then I made the big mistake of attempting to disable WiFi by right-clicking on the wireless applet and un-checking "Enable Wireless." Since then, I cannot get wireless working again. The wireless applet reports that "wireless is disabled by hardware switch" but there is no hardware switch on this computer. Issuing a rfkill list yields the following: 0: dell-wifi: Wireless LAN Soft blocked: yes Hard block: yes 1: phy0: Wireless LAN Soft blocked: no Hard blocked: yes I'm in way over my head, and my computer is now useless. Help!!!

    Read the article

  • Did Blowing Into Nintendo Cartridges Really Help?

    - by Jason Fitzpatrick
    Anyone old enough to remember playing cartridge-based games like those that came with the Nintendo Entertainment System or its successors certainly remembers how blowing across the cartridge opening always seemed to help a stubborn game load–but did blowing on them really help? Mental Floss shares the results of their fact finding mission, a mission that included researching the connection mechanism in the NES, talking to Frank Viturello (who conducted an informal study on the effects of moisture on cartridge connectors), and otherwise delving into the history of the phenomenon. The most interesting part of the analysis, by far, is their explanation of how blowing on the cartridge didn’t do anything but the ritual of removing the cartridge to blow on it did. Hit up the link below for the full story. Did Blowing into Nintendo Cartridges Really Help? [Mental Floss] How Hackers Can Disguise Malicious Programs With Fake File Extensions Can Dust Actually Damage My Computer? What To Do If You Get a Virus on Your Computer

    Read the article

  • Toolbar Cleaner Strips Toolbars, Add-ons, and Browser Helper Objects

    - by Jason Fitzpatrick
    If you’re trying to remove all the crap off a friend’s bogged down computer, Toolbar Cleaner is a handy little app that does a thorough job stripping away spammy toolbars, dubious add-ons, and browser helper objects. Toolbar Cleaner is a free application that helps remove unwanted garbage from your Internet Explorer, Firefox, and Google Chrome installations–including third-party toolbars, extensions/add-ons, and browser helper objects (plug-ins that modify your browser behavior and can contain malware). If you’re dealing with a machine drowning under all the toolbars and crapware that have snuck onto the system, it’s a nearly one-click solution to purging all of them. Hit up the link below to read more about the software and grab a copy. Toolbar Cleaner is freeware, Windows only. Toolbar Cleaner [via Freeware Genius] HTG Explains: Why It’s Good That Your Computer’s RAM Is Full 10 Awesome Improvements For Desktop Users in Windows 8 How To Play DVDs on Windows 8

    Read the article

  • HTG Explains: What is the Windows Page File and Should You Disable It?

    - by Chris Hoffman
    Windows uses a page file to store data that can’t be held by your computer’s random-access memory when it fills up. While you can tweak the page file settings, Windows can manage the page file fine on its own. The Windows page file is somewhat misunderstood. People see it as the cause of slowdowns because it’s slower to use the page file than your computer’s RAM, but having a page file is better than not having one. Image Credit: Blake Patterson on Flickr HTG Explains: What is the Windows Page File and Should You Disable It? How To Get a Better Wireless Signal and Reduce Wireless Network Interference How To Troubleshoot Internet Connection Problems

    Read the article

  • rc.local is not always executed upon boot

    - by starcorn
    Hey, I have some weird problem with the rc.local file which is located in /etc/rc.local the thing is that it is not always running when I boot up the laptop. Maybe every second time, I haven't counted. Anyway when that happens I have to manually go to terminal and type sudo /etc/init.d/rc.local start, which kinda kills the purpose of having this script. Anyone know what the problem could be? EDIT Since this wasn't obvious. This is an issue where I make a fresh boot up. Which mean I have shut down the computer. And next time when I boot up the computer, the rc.local file is randomly deciding whether it will automatically start or not. Here's a copy of what my rc.local file contains echo -n 255 > /sys/devices/platform/i8042/serio1/serio2/sensitivity echo level 2 > /proc/acpi/ibm/fan touch /home/starcorn/Desktop/foo rfkill block bluetooth exit 0

    Read the article

  • How does btrfs RAID work in degraded mode?

    - by turbo
    My idea was that (using loopback devices) it works like this Create the raid array sudo mkfs.btrfs -m raid1 -d raid1 /dev/loop1 /dev/loop2 You mount them sudo mount /dev/loop1 /mnt and mark them touch goodcondition You unmount and simulate disk failure (remove disk or delete loopback device loop2 in my case) You mount degraded -o degraded and mark again touch degraded You add the bad disk again sudo btrfs dev add /dev/loop2 You rebalance sudo btrfs fi ba /mnt And Raid 1 should work again. But that's not the case. sudo btrfs fi show: Total devices 3 FS bytes used 28.00KB devid 3 size 4.00GB used 264.00MB path /dev/loop1 devid 2 size 4.00GB used 272.00MB path /dev/loop2 *** Some devices missing The file degraded lives on loop1 but not on loop2 when loop2 is mounted in degraded mode. Why is that?

    Read the article

  • When is an object oriented program truly object oriented?

    - by Syed Aslam
    Let me try to explain what I mean: Say, I present a list of objects and I need to get back a selected object by a user. The following are the classes I can think of right now: ListViewer Item App [Calling class] In case of a GUI application, usually click on a particular item is selection of the item and in case of a command line, some input, say an integer representing that item. Let us go with command line application here. A function lists all the items and waits for the choice of object, an integer. So here, I get the choice, is choice going to conceived as an object? And based on the choice, return back the object in the list. Does writing this program like the way explained above make it truly object oriented? If yes, how? If not, why? Or is the question itself wrong and I shouldn't be thinking along those lines?

    Read the article

  • Flutter Enabled Hand Gesture Control of Your Music and Movies

    - by Jason Fitzpatrick
    You’ve got a dozen windows open, your media player is buried underneath somewhere, and the phone rings. Do you reach for the speaker power button, dig through the windows, or simply wave your hand to pause the music? With Flutter, a simple gesture is all it takes. Flutter is a free application for Windows and Mac OS X that turns your webcam into a gesture-recognition tool and your hand into a remote for your media applications. By lifting your your hand palm out, making a fist, or using other simple gestures, you can pause or otherwise interact with your media players. Hit up the link below to grab a free copy of Flutter. FlutterApp [via MakeUseOf] How Hackers Can Disguise Malicious Programs With Fake File Extensions Can Dust Actually Damage My Computer? What To Do If You Get a Virus on Your Computer

    Read the article

  • Unable to wake display with remote

    - by Eugene
    I'm running an HTPC (xbmc) without a keyboard/mouse attached, running oneiric. After some indeterminate amount of time, sometime between 1 and 12 hours, the display goes to sleep. The computer itself is not sleeping, I can still SSH to it from another computer. The remote will not wake the display. The IR receiver is working, as irw will show me the remote key presses. The only way to get my display back is to restart the display manager, lightdm in this case. Does anybody know a way to keep the display from going to sleep? I don't really need any power management at all considering that it connects to my TV and when I want my display to go to sleep, I turn off my TV.

    Read the article

< Previous Page | 229 230 231 232 233 234 235 236 237 238 239 240  | Next Page >