Search Results

Search found 7391 results on 296 pages for 'record locking'.

Page 236/296 | < Previous Page | 232 233 234 235 236 237 238 239 240 241 242 243  | Next Page >

  • LDAP Account Locked Out Sporadically after Password change - Finding the source of invalid attempts

    - by CityView
    On a small network of machines (<1000) we have a user whose account is being locked out after an indeterminate interval following a password change. We are having severe difficulties finding the source of the invalid logon attempts and I would appreciate it greatly if some of you could go through your thought process and the checks you would perform in order to fix the problem. All I know for sure is that the account is locked out several (5+) times a day, I can't even be sure it's due to failed login attempts as there is no record of failure until the account is locked. So far I have tried; Logging the account out of everything we can think of and back in with the new password Scanning the user's box for any non standard software which might perform an LDAP lookup Checking all installed services on our production boxes to check none are attempting to run under the account Changing the user back to their old password (Problem persists so perhaps password change is a red herring) Wireshark on a box where lots of LDAP authentication is performed - Rejects only occur after account is already locked out Clearing the credential cache in - Control Panel - User Accounts - Advanced Looking at the local I'm at a loss for what to try. I am happy to try any suggestions you have in order to diagnose the issue. I think my question boils down to a simple request; I need a technique for deriving the source (Application/Host) of the invalid login attempts which are causing the account to be locked. I'm not sure if that's even possible but I suspect there must be more I can try. Many thanks, CityView

    Read the article

  • What's going on with traceroute?

    - by Kevin
    The following is what happens when I run traceroute from a certain location: # traceroute google.com traceroute to google.com (74.125.227.39), 30 hops max, 60 byte packets 1 gateway.local.enactpc.com (10.0.0.1) 0.138 ms 0.101 ms 0.084 ms 2 * * * 3 * * * 4 * * * 5 * * * 6 * * * 7 * * * 8 * * * 9 * * * 10 * * * 11 * * * 12 * * * 13 * * * 14 * * * 15 * * * 16 * * * 17 * * * 18 * * * 19 * * * 20 * * * 21 * * * 22 * * * 23 * * * 24 * * * 25 * * * 26 * * * 27 * * * 28 * * * 29 * * * 30 * * * Absolutely nothing of interest... Now, originally I thought this was just a fact of the location's network set up. (I assume they block pings or something...) However, watch what happens when I use nmap to run a traceroute... # nmap -sP --traceroute google.com Starting Nmap 5.21 ( http://nmap.org ) at 2012-09-25 22:18 CDT Nmap scan report for google.com (74.125.227.40) Host is up (0.034s latency). Hostname google.com resolves to 11 IPs. Only scanned 74.125.227.40 rDNS record for 74.125.227.40: dfw06s06-in-f8.1e100.net TRACEROUTE (using proto 1/icmp) HOP RTT ADDRESS 1 0.19 ms gateway.local.enactpc.com (10.0.0.1) 2 1.93 ms 99-20-92-1.lightspeed.austtx.sbcglobal.net (99.20.92.1) 3 25.61 ms 99-20-92-2.lightspeed.austtx.sbcglobal.net (99.20.92.2) 4 ... 6 7 23.68 ms 12.83.68.137 8 31.30 ms gar23.dlstx.ip.att.net (12.122.85.73) 9 ... 10 31.82 ms 72.14.233.65 11 32.27 ms 209.85.250.77 12 32.98 ms dfw06s06-in-f8.1e100.net (74.125.227.40) Nmap done: 1 IP address (1 host up) scanned in 3.29 seconds When using nmap I get A LOT more results than with traceroute, why? Note, I checked, and the difference in target IP addresses is not related...

    Read the article

  • Shortcut to "printer and faxes" on another computer

    - by Doltknuckle
    I have a print server running windows server 2008 that has about 50 printers on it. In windows XP, I was able to connect to the server using the UNC name and make a shortcut to the "printers and faxes" folder. (For the record, I know that it really isn't a folder, but that's outside the scope of this question.) I have recently switched to windows 7 and I find that the jump lists are really useful. One of the things I want to do is make it easy to connect to that server's "printers and faxes" folder. I would like to use something like a shortcut that I can open and go immediately to that location. The problem is that windows 7 doesn't have a way to create a shortcut like you could in WinXP. They have a button on the toolbar that says "view remote printers" which sends you to the correct folder. I'd like to avoid having to type out the server name. I also can't use the "view network" link in windows explorer. Our organization has over 6,000 machines and viewing the network lists all of them. This is all about saving time by using the minimum number of mouse clicks and key presses in normal operation. Does anyone have any suggestions?

    Read the article

  • Intermittent Trouble Entering Hibernate on WinXP

    - by kquinn
    My personal desktop, running 32-bit Windows XP SP2 (with 4GB RAM, 2.75GB addressable, swap disabled, hiberfil.sys existing and contiguous on C:\; SP3 is not installed because SP2 has been working fine and I do not want to re-qualify with SP3 just for sheer perversity) typically gets hibernated at night. For a long time this worked great, but recently the machine has had trouble entering hibernation. Sometimes when I press my power button (configured to hibernate), the box will start the procedure for hibernating (i.e., go to the blue "Windows XP" background logo and display a message about entering hibernation), but before displaying the usual blue-on-black hibernation progress bar it will drop back to the desktop. No error messages appear, on screen or in the system log. The only record of unsuccessful hibernation attempts in the system log, which proudly proclaims that "The Windows Image Acquisition (WIA) service entered the running state." once per failed hibernation attempt. The problem is almost certainly resource related: if I then close one or more applications which are running, and repeat the exact same process, the machine will hibernate perfectly. There does not appear to be a reliable high-water mark for virtual or physical memory use, below which the machine is guaranteed to hibernate; it's different every time (though typically, below about 1.1–1.4 GB memory usage seems to be where hibernate succeeds most often). Memory may not even be the relevant resource; as far as I know, it could also be handles or sockets. This behavior is relatively recent: it has only started in the last few months; before then, I could hibernate reliably no matter what the current resource use of the system. This machine claims to have hotfix Q909095 installed, but since the symptoms of my problem match KB909095 rather well, I'm suspicious if this fix is actually working as intended. Any ideas on how to fix this or where to start debugging?

    Read the article

  • mod_rewrite not working for subdomain in Apache2

    - by Matt
    Hi, I'm having some trouble with mod_rewrite. So I'm implementing it through .htaccess, and I can get it working on my main vhost, domain.com - what I want it to do is rewrite http:// domain.com to force it to https:// domain.com, which it does well. I want to have name-based vhosts for the one IP with the following redirects: (I'm breaking up domain names with a space because otherwise serverfault recognises them as links) http:// domain.com -- https:// domain.com http:// staging.domain.com -- https:// staging.domain.com http:// test.domain.com -- https:// test.domain.com http:// beta.domain.com -- https:// beta.domain.com domain.com redirects to https:// domain.com, but staging.domain.com doesn't, although I can access https:// staging.domain.com. The .htaccess is identical for both, just with the domain name different. It doesn't seem to do any rewriting at all for staging.domain.com, I've tested this by trying to get it to rewrite to www.google.com. I have a wildcard DNS record, *.domain.com which points to the domain IP. Is there a particular way I should have the virtualhosts configured to allow this? I keep reading in the Apache documentation that it doesn't support multiple SSL name-based vhosts. But I can access both https:// domain.com and https:// staging.domain.com just fine. Any thoughts? Thanks to everyone for your help with this.

    Read the article

  • SQL 2008 R2 replication error: The process could not connect to Distributor

    - by Lance Lefebure
    I have two servers running SQL 2008 R2 Standard, each with an instance named "MAIN". I have a small test database on my primary server (one table, 13 rows) that I want to replicate to a second server as a proof-of-concept for some larger databases that I want to replicate. I set up the primary server to be a publisher and distributor, and set the database to do transactional replication. I copied the data to the second server via a backup/restore, not via a snapshot (which I'll have to do with the larger databases due to database size and limited bandwidth). I followed the instructions here: http://gnawgnu.blogspot.com/2009/11/sql-2008-transactional-replication-and.html Now on the subscriber, I go under Replication / Local Subscriptions / Right click / Properties on my subscription to the DB. The status of the last synchronization shows a status of: "The process could not connect to Distributor 'PRIMARYSERVER\MAIN'." Data IS replicating from the primary to the secondary. Any record I add on the primary shows up on the secondary server within seconds. Is the Distributor part of the Snapshot system that I'm not using, or is it part of the transaction replication stuff? Thanks, Lance

    Read the article

  • Are there any viable DNS or LDAP alternatives for distributed key/value storage and retrieval?

    - by makerofthings7
    I'm working on a software app that needs distributed decentralized name resolution, and isn't bound to TCP/IP. Or more precisely, I need to store a "key" and look up it's value, and the key may be a string, a number, or any other realistic data type. Examples: With a phone number, look up a name. (or with an area code, redirect to the server that handles that exchange) With an IP Address get a DNS name, or a Whois contact (string value) With a string, get an IP, ( like a DNS TXT or SRV record). I'm thinking out of the box here and looking for any software that allows for this. (more info below) Are there any secure, scalable DNS alternatives that have gained notoriety? I could ask on StackOverflow, but think the infrastructure groups would have better insight on this. Edit More info: I'm looking at "Namecoin" the DNS version of Bitcoin, and since that project is faltering, I'm looking at alternative ways to store name-value pairs, with an optional qualifier. I think a name value pair is of global interest is useful, but on a limited scale. Namecoin tried to be too much, and ended up becoming nothing. I'm trying to solve that problem in researching alternatives and applying distributed technologies where applicable. Bitcoin/Namecoin offers a Distributed Hash Table, which has some positive aspects, but not useful for DNS, except for root servers.

    Read the article

  • Most cost efficient way to backup Subversion data to S3?

    - by sludge
    I'm looking at using S3 as an offsite backup repo for my Subversion database. When I dump my SVN database, it's about 10 gigabytes. I would like to avoid the charge of uploading that data repeatedly. The anatomy of this large file such that new changes to Subversion modify the tail of the file, with everything else staying the same. Because Amazon S3 does not allow you to "patch" files with changes, I will have to upload ten gigs every time I instantiate a backup after doing a simple submit to Subversion. Here are the options as I see them: Option 1 I am looking at duplicity which has --volsize which splits data over an amount of megs. Is it possible to split the Subversion dumps using this so further incremental backups are measured in megabytes? Option 2 Can I just backup the hot subversion repository? This seems like a bad idea if it is in the middle of writing a submit. However, I have the option of taking the repo offline between the hours of midnight and 4am. Each revision in my Berkeley DB uses a file as its record.

    Read the article

  • How best to manage my growing data in Excel?

    - by Mike
    This isn't a question about formulas or features in Excel. I'm debating the correct/best way to manage the growing amount of data 'I have to' manage in Excel (I produce PIVOT tables/reports for my management). DATA: I record the number of publications we order: cost, date ordered, start and end of subscription, who requested it, when they ordered it, when I ordered it, will it be cancelled next year, etc, etc, etc. DILEMMA: Obviously we re-order a lot of the same publications, so depending on how I manage the data I could be duplicating all over the place. OPTION 1: So, do I use ROWs = publication name in Row 1 and all the related columns for each financial year are copied and pasted after each financial year ready for the new FY information? This will lead to me going to column ZZ. OPTION 2: Or, do I use COLUMNs = each row has only one FY information for each publication and if we re-order or cancel a publication I re-type the publication name in a row below and fill in appropriate columns? This will lead to a long list of publications down to row 10000, and potential for misspelling of repeat ordered publication names. IDEAS: What's the best way - thinking in terms of pivot table best practice, being able to sum or count easy, report formatting, etc. Any best practices much appreciated.

    Read the article

  • Fixing a typo in machine name

    - by justSteve
    When i installed windows i had a typo in the machine name that i corrected from the system's 'Computer Name/Domain Changes' - the workstation is a member of a workgroup not a domain. From everything i can see the renamed machine name is correct. Shift gears.... I'm importing SQL logins from my remote server to this, my development workstation and have used the script presented here - a script that generates a CREATE statement for each login found. While I was preparing to run this script's output (from the remote box) i needed to change the domain name from the remote to my local's name - so i ran the same script locally (in order to see what SQL things my domain name is. SQL has the original machine name - the one with the typo. However, the scripts are tossing errors if i try to create logins with that identifier. CREATE LOGIN [Setve\Admin] FROM WINDOWS WITH DEFAULT_DATABASE = [master] But works correctly if i use the updated machine name: CREATE LOGIN [Steve\Admin] FROM WINDOWS WITH DEFAULT_DATABASE = [master] So the problem is: do i have a problem i need to solve? Somewhere, deep in the guts of SQL Server, it has record of a Domain name that does not exist. Should i find and fix that discrepancy? thx

    Read the article

  • Sending mails via Mutt and Gmail: Duplicates

    - by Chris
    I'm trying to setup mutt wiht gmail for the first time. It seems to work pretty well, however when I send a mail from Mutt i appears twice in Gmail's sent folder. (I assume it's also sent twice - I'm trying to validate that) My configuration (Stripped of coloring): # A basic .muttrc for use with Gmail # Change the following six lines to match your Gmail account details set imap_user = "XX" set smtp_url = "[email protected]@smtp.gmail.com:587/" set from = "XX" set realname = "XX" # Change the following line to a different editor you prefer. set editor = "vim" # Basic config, you can leave this as is set folder = "imaps://imap.gmail.com:993" set spoolfile = "+INBOX" set imap_check_subscribed set hostname = gmail.com set mail_check = 120 set timeout = 300 set imap_keepalive = 300 set postponed = "+[Gmail]/Drafts" set record = "+[Gmail]/Sent Mail" set header_cache=~/.mutt/cache/headers set message_cachedir=~/.mutt/cache/bodies set certificate_file=~/.mutt/certificates set move = no set include set sort = 'threads' set sort_aux = 'reverse-last-date-received' set auto_tag = yes hdr_order Date From To Cc auto_view text/html bind editor <Tab> complete-query bind editor ^T complete bind editor <space> noop # Gmail-style keyboard shortcuts macro index,pager y "<enter-command>unset trash\n <delete-message>" "Gmail archive message" macro index,pager d "<enter-command>set trash=\"imaps://imap.googlemail.com/[Gmail]/Bin\"\n <delete-message>" "Gmail delete message" macro index,pager gl "<change-folder>" macro index,pager gi "<change-folder>=INBOX<enter>" "Go to inbox" macro index,pager ga "<change-folder>=[Gmail]/All Mail<enter>" "Go to all mail" macro index,pager gs "<change-folder>=[Gmail]/Starred<enter>" "Go to starred messages" macro index,pager gd "<change-folder>=[Gmail]/Drafts<enter>" "Go to drafts" macro index,pager gt "<change-folder>=[Gmail]/Sent Mail<enter>" "Go to sent mail" #Don't prompt on exit set quit=yes ## ================= #Color definitions ## ================= set pgp_autosign

    Read the article

  • Dealing with upgrade of libevent on Amazon AWS

    - by Dreen
    I am building an application (in Python) on Amazon EC2 that has a following dependency chain: gevent-websocket ---> gevent ---> libevent The last one (libevent) got upgraded on Sunday and my server is now generating this error: (...) File "/usr/lib/python2.6/site-packages/gevent-0.13.7-py2.6-linux-x86_64.egg/gevent/__init__.py", line 41, in <module> from gevent import core ImportError: libevent-1.4.so.2: cannot open shared object file: No such file or directory Not wanting to spend much time on the issue, I tried to mitigate it by creating a symlink to an always-recent version: $ sudo ln -s /usr/lib64/libevent.so /usr/lib64/libevent-1.4.so.2 But it didn't quite work: (...) File "/usr/lib/python2.6/site-packages/gevent-0.13.7-py2.6-linux-x86_64.egg/gevent/__init__.py", line 41, in <module> from gevent import core ImportError: /usr/lib/python2.6/site-packages/gevent-0.13.7-py2.6-linux-x86_64.egg/gevent/core.so: undefined symbol: current_base I am a bit stumped as to how to proceed. Should I create more symlinks? To what? Or is there a better way to solve this problem... PS. For the record I am using Amazon AMI.

    Read the article

  • Can't get subdomain to point to working collabNet server - what am I doing wrong?

    - by Jared
    Hello everyone, I am running a web server using CollabNet SubVersion EDGE. You can view it at 71.13.105DOT51 I also run another website, http://www.tutorialcraft.com. I went into my Cpanel, and created a DNS record as follows: svn.tutorialcraft.com. 14400 IN A 71.13.105.51 Yet, if you go to http://svn.tutorialcraft.com, it doesn't load. I tested to see if I was doing some wrong, so I created a ebay.tutorialcraft.com and pointed it to eBay servers, and it worked fine (it's not up now). Anyone have any ideas? Thanks UPDATE NOTES: I tried to point svn.tutorialcraft.com to my original IP address (the one that www.tutorialcraft.com is pointed to, and it still won't load. Also, may be worthy of note, I am running a wordpress multi-site server, and I have disabled blog redirection. Here is a sample of my .htaccess as well: RewriteEngine On RewriteCond %{HTTP_HOST} ^tutorialcraft\.com RewriteRule (.*) http://www.tutorialcraft.com/$1 [R=301,L] RewriteBase / RewriteRule ^index\.php$ - [L] # uploaded files RewriteRule ^files/(.+) wp-includes/ms-files.php?file=$1 [L] RewriteCond %{REQUEST_FILENAME} -f [OR] RewriteCond %{REQUEST_FILENAME} -d RewriteRule ^ - [L] RewriteRule . index.php [L]

    Read the article

  • vSphere Promiscuous mode only receiving packets one way from network switch

    - by steve.lippert
    We have two network switches, a POE switch (SwitchA) to power our phones / users computers and a non-POE switch (SwitchB for the rest network.) Each switch is setup to do port mirroring to support our VoIP recording system. SwitchA does port mirroring on specific ports if we need to record a user. SwitchB mirrors one port to monitor our work at home users (Internet comes in from managed router, to switch, back out to our firewall.) These two port mirroring setups feed into one vmware vSphere 4.1 server, it has four total physical cards. The other two NICs feed into an unmanaged switch for connecting to the rest of the network. Once into the vSphere server all network ports go into a vSwitch, and then one of the servers (Windows 2008 R2) sniffs them out and does its thing. Everything is working fine and dandy from SwitchB. But on SwitchA we only receive one side of the VoIP packets (going out to the phone, nothing coming in from the phone). Troubleshooting steps I have taken so far: I hooked up my laptop to the monitor port on SwitchB and I see both sides of the packets. I swapped which network interface is plugged into the monitor port on SwitchA. Because everything feeds into one vSwitch / vNetwork and both sides of the conversation arrive just fine from SwitchB I believe everything is configured correctly on the vSphere server/guest. What could be causing one way packets to arrive on my guest machine from only one interface, but not the other? Could a bad cable be causing the problems from SwitchB?

    Read the article

  • Creating a test database with copied data *and* its own data

    - by Jordan Reiter
    I'd like to create a test database that each day is refreshed with data from the production database. BUT, I'd like to be able to create records in the test database and retain them rather than having them be overwritten. I'm wondering if there is a simple straightforward way to do this. Both databases run on the same server, so apparently that rules out replication? For clarification, here is what I would like to happen: Test database is created with production data I create some test records that I want to keep running on the test server (basically so I can have example records that I can play with) Next day, the database is completely refreshed, but the records I created that day are retained. Records that were untouched that day are replaced with records from the production database. The complication is if a record in the production database is deleted, I want it to be deleted on the test database too, so I do want to get rid of records in the test database that no longer exist in the production database, unless those records were created within the test database. Seems like the only way to do this would be to have some sort of table storing metadata about the records being created? So for example, something like this: CREATE TABLE MetaDataRecords ( id integer not null primary key auto_increment, tablename varchar(100), action char(1), pk varchar(100) ); DELETE FROM testdb.users WHERE NOT EXISTS (SELECT * from proddb.users WHERE proddb.users.id=testdb.users.id) AND NOT EXISTS (SELECT * from testdb.MetaDataRecords WHERE testdb.MetaDataRecords.pk=testdb.users.pk AND testdb.MetaDataRecords.action='C' AND testdb.MetaDataRecords.tablename='users' );

    Read the article

  • Is there a utility to visualise / isolate and watch application calls

    - by MyStream
    Note: I'm not sure what to search for so guidance on that may be just as valuable as an answer. I'm looking for a way to visually compare activity of two applications (in this case a webserver with php communicating with the system or mysql or network devices, etc) such that I can compare the performance at a glance. I know there are tools to generate data dumps from benchmarks for apache and some available for php for tracing that you can dump and analyse but what I'm looking for is something that can report performance metrics visually from data on calls (what called what, how long did it take, how much memory did it consume, how can that be represented visually in a call stack) and present it graphically as if it were a topology or layered visual with different elements of system calls occupying different layers. A typical visual may consist of (e.g. using swim diagrams as just one analogy): Network (details here relevant to network diagnostics) | ^ back out v | Linux (details here related to firewall/routing diagnostics) ^ back to network | | V ^ back to system Apache (details here related to web request) | | ^ response to V | apache PHP (etc) PHP---------->other accesses to php files/resources----- | ^ v | MySQL (total time) MySQL | ^ V | Each call listed + time + tables hit/record returned My aim would be to be able to 'inspect' a request/range of requests over a period of time to see what constituted the activity at that point in time and trace it from beginning to end as a diagnostic tool. Is there any such work in this direction? I realise it would be intensive on the server, but the intention is to benchmark and analyse processes against each other for both educational and professional reasons and a visual aid is a great eye-opener compared to raw statistics or dozens of discrete activity vs time graphs. It's hard to show the full cycle. Any pointers welcome. Thanks! FROM COMMENTS: > XHProf in conjunction with other programs such as Perconna toolkit > (percona.com/doc/percona-toolkit/2.0/pt-pmp.html) for mySQL run apache > with httpd -X & (Single threaded debug mode and background) then > attach with strace -> kcache grind

    Read the article

  • NVidia TwinView - slow rendering on dual desktop

    - by lisak
    Hey, does anybody have experience with it ? I've set it up 4 times on 4 different machines. And there was always problems with slow rendering ( for instance : scrolling pages in browser is not fluent). But there always was something that finally made it work perfectly... I remember that one time this option helped, but not now Option "RenderAccel" "1" Nvidia geforce 8400GS or Zotac geforce 9500GT Monitors connected via dvi and hdmi connectors proper nvidia driver installed Section "ServerLayout" Identifier "X.org Configured" Screen 0 "Screen0" 0 0 InputDevice "Mouse0" "CorePointer" InputDevice "Keyboard0" "CoreKeyboard" Option "Xinerama" "0" EndSection Section "Files" ModulePath "/usr/lib64/xorg/modules" FontPath "/usr/share/fonts/local" FontPath "/usr/share/fonts/TTF" FontPath "/usr/share/fonts/OTF" FontPath "/usr/share/fonts/Type1" FontPath "/usr/share/fonts/misc" FontPath "/usr/share/fonts/CID" FontPath "/usr/share/fonts/75dpi/:unscaled" FontPath "/usr/share/fonts/100dpi/:unscaled" FontPath "/usr/share/fonts/75dpi" FontPath "/usr/share/fonts/100dpi" FontPath "/usr/share/fonts/cyrillic" EndSection Section "Module" Load "dri2" Load "glx" Load "extmod" Load "record" Load "dbe" EndSection Section "InputDevice" Identifier "Keyboard0" Driver "kbd" EndSection Section "InputDevice" Identifier "Mouse0" Driver "mouse" Option "Protocol" "auto" Option "Device" "/dev/input/mice" Option "ZAxisMapping" "4 5 6 7" EndSection Section "Monitor" Identifier "Monitor0" VendorName "Unknown" ModelName "Acer AL1715" HorizSync 30.0 - 83.0 VertRefresh 50.0 - 75.0 EndSection Section "Device" Identifier "Nvidia" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "MSI big bang-fuzion" EndSection Section "Device" Identifier "Device0" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "GeForce 8400 GS" EndSection Section "Screen" Identifier "Screen0" Device "Device0" Monitor "Monitor0" DefaultDepth 24 Option "RenderAccel" "1" Option "AllowGLXWithComposite" "1" Option "TwinView" "1" Option "TwinViewXineramaInfoOrder" "DFP-1" Option "metamodes" "CRT: 1280x1024 +1920+0, DFP: 1920x1080 +0+0" SubSection "Display" Depth 24 EndSubSection EndSection

    Read the article

  • Email delivering but not receiving from Gmail

    - by Karthik Malla
    Host Record type Value 65.75.241.26 / 24 PTR softmail.me. accs.softmail.me. A 65.75.241.26 beta.softmail.me. A 65.75.241.26 ftp.softmail.me. CNAME softmail.me. lists.softmail.me. CNAME softmail.me. mail.softmail.me. A 65.75.241.26 mssql.softmail.me. A 65.75.241.26 ns.softmail.me. A 65.75.241.26 sitebuilder.softmail.me. A 65.75.241.26 softmail.me. NS ns.softmail.me. softmail.me. A 65.75.241.26 softmail.me. MX (10) mail.softmail.me. test.softmail.me. A 65.75.241.26 webmail.softmail.me. A 65.75.241.26 www.accs.softmail.me. CNAME accs.softmail.me. www.beta.softmail.me. CNAME beta.softmail.me. www.softmail.me. CNAME softmail.me. www.test.softmail.me. CNAME test.softmail.me. The above are the DNS settings of my email server and mail incoming/outgoing is done by softmail.me:25/110 using which I am able to send emails but unable to receive. Can anyone tell me where the problem lies at?

    Read the article

  • PCI Tv Tuner not receiving signal

    - by C-dizzle
    I inherited an Angel II PCI Dual TV Tuner card, popped it into my computer's PCI slot, plugged in my coax cable, but am having trouble getting any type of signal to it. The computer I am using is Windows 7 Ultimate 32 bit, I know the card works because the computer recognizes it and installs the drivers, or at least I assume it works because of that. I'm trying to use Windows Media Center to watch/record tv. Here are a few things I have tried to get it working: Uninstalled/Reinstalled the newest drivers Tried hooking up an antenna to the coax input instead of my cable Instead of using cable splitter, went directly from wall output into card with coax cable Tried using different output on splitter in case the out port was bad I haven't tried a different coax cable yet, it should be fine since it's pretty new. Since this is my first time setting up a TV Tuner card, is there anything specific that I need to do with it? Is there any configuration that needs to be done on it? Do I need to have a digial receiver? I was getting pretty frustrated with it so I wanted to turn here to the experts, I'm sure someone can help me figure it out.

    Read the article

  • Is there an application to log component temperatures to file?

    - by MrVimes
    I purchased a computer a month or two ago (core i7, 24gb ram, geforce gtx 590, windows 7 ultimate). Within the last week it began to bluescreen regularly. I tried lots of things (check hds, check memory, reinstall windows etc..) but it still bluescreened. At the time my temps were as follows... CPU - aprox 40/50c. GPU - arpox 60 idle, aprox 90 during heavy use. HDDs - aprox 55c after the PC had been on a while. I thought the 55c was ok, but I have since realized it was probably too high and may have been the direct cause of the bluescreening. I've installed a spare fan I had in the front of the PC blowing air in, (so there's airflow from front to back) Since then, obviously, all my temps are down. Especially the HDDs - three of them reach 30c and one has been up to 47c (it is some distance away from the airflow, in one of the 5.25inch drive bays) I haven't had the PC on for as long as it would normally take to bluescreen yet, but If it does I want to know what all the temps were right before the bluescreen. I have tried Everest but it only shows me realtime temps or gives me the ability to create one-off reports. I want something that can record all the temps to a file at 30 seconds intervals. If the computer bluescreens I can load it up again and check the last entry in the file. Side question: Am I right in thinking 55c was far too hot for a HDD? (It might have got higher than that before the bluescreens.. I don't know) Another side question: Is 47c too high? This is actually why I am asking the main question - I am concerned that this one drive that isn't getting the benefit of the extra fan may still cause the computer to bluescreen.

    Read the article

  • Postfix auto create Maildir

    - by Eugene
    I've been beating my head against a wall for a while now on this one. Basically, here is the rundown: Our MX record points to a frontend SMTP server, which contains aliases for actually routing the mail. No alias, no access to the backend storage server, which is what our clients connect to. I'm upgrading the backend email server. Currently, a user is created for every email user on the server, which creates the mailbox. On the new server, everything autheticates through PAM to an LDAP server (all of which is working properly). My goal is to get Postfix to create the Maildir directory for the user automatically. This works fine when I have the /home directory with 777 permissions, but for obvious reasons, this should be avoided. I would like to do this with 775 permissions on /home with a group owner of whatever user Postfix is running as, but I can't seem to figure out what user to use. With the 777 permissions, the /home/$user/Maildir directory is created on message delivery. Does anybody know how I can do this without 777 permissions? The system I am working on is a 64-bit Debian Lenny 5.07 install. Any advice would be appreciated.

    Read the article

  • Win7 Hangs During App Install/Upgrade/Uninstall

    - by JadeMason
    I have a custom built PC that intermittently hangs when installing, uninstalling, or upgrading applications. Technical Specs ASUS P5E w/ WiFi Motherboard Intel Core2 Quad Q6600 Processor 4x 2GB G.Skill DDR2 800 SDRAM ASUS EAH2900XT / Radeon HD 2900XT 512MB Video Card Under normal operation the machine runs reliably, even under heavy load, such as video transcoding. The temperature never gets anywhere near where I would worry about it. However, the machine regularly hangs (complete lockup, no response to keyboard or mouse, no activity on-screen) when either installing a new application, uninstalling an existing application, or applying patches to existing applications or the OS. This is extremely frustrating as this machine is primarily used as a HTPC. Several apps are configured for automatic updates, and these updates sometimes cause the machine to lockup while we are watching content on the PC. In previously investigating this issue, I found one likely problem could be my Logitech Webcam. The Logitech software has a bug that leaves an entry in HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\ Control\SessionManager\PendingFileRenameOperations Which references the Temp directory. My registry contained this error, so I uninstalled the webcam software and deleted this registry key value. Unfortunately, the machine will still intermittently hang. I've noticed that the hangs always happen when an install/upgrade/uninstall requires elevated privileges (presumably to modify the registry). I can typically get at least one install/upgrade/uninstall to complete after a reboot, but after that it is a game of russian roulette to see if the operation will succeed or hang the machine. The event log is not helpful, as log messages end at the time of the hang, with no record of a warning or error. My only recourse when the machine hangs in this way is to perform a hard reset/power cycle. Any tips on how to further debug this issue are greatly appreciated.

    Read the article

  • Troubles with apache and virtual hosts

    - by xZero
    I have a BIG problem. I have VPS with Debian OS, and LAMP installed. Fresh install. For control panel i using Webmin. Now i trying to setup multiple sub-domains on my server using webmin for example: downloads.my-domain.com cpanel.my-domains.com forum.my-domains.com But problem what is happening is next, while i using no virtual hosts, everything works perfectly when i accessing it using my-domain.com, but when i add Virtual host, i cann access it but my-domain.com becomes unavilable because it redirects to virtual hosts i added. When i add more than 2 virtual hosts, problem is still here. Also, when i try to access to virtual server for example downloads.my-domain.com, it redirects again to cpanel.my-domains.com When i delete virtual hosts, access to my-domain.com is succesfull... What i known: - That is not problem with my domain provider. I correctly added subdomains and added host record to my VPS IP. - I added unique name to every single virtual host. - There are no two same virtual hosts - Every virtaul hosts have own directory: for example: downloads.my-domain.com have own WWW dir: /var/downloads Can somebody help me? Thanks.

    Read the article

  • DNS lookup fails when with all the MAC workstations

    - by user39564
    Hi, I am having this insane problem. We are mac-heavy users. Around 10 workstations, one Xserve server, two windows workstation and one Linux (me). Last year I added an A record to our domain's DNS. However we had to change that a few months ago to a new IP. But all the Mac workstations fail to resolve the proper DNS and they still resolve to the old IP, even after 2 months. On both the windows workstation and my linux box a simple nslookup resolves to proper IP. However, on ALL the mac workstation, dig and nslookup report the old IP address. From my linux workstation: jp@lo:~$ nslookup - 208.67.222.222 client.xyz.com Server: 208.67.222.222 Address: 208.67.222.222#53 Non-authoritative answer: Name: client.xyz.com Address: 68.71.40.xx But when I am trying the exact same command from any Mac workstation, I get the old IP: $ nslookup - 208.67.222.222 client.xyz.com Server: 208.67.222.222 Address: 208.67.222.222#53 Non-authoritative answer: Name: client.xyz.com Address: 98.143.155.xx The strange thing is that this only happens in our internal network. No problem from home nor from another server. I did try to flush the DNS, don't worry. It did not help. I am starting to wonder if my router (OpenWRT) or Mac OS X Server is not in some way spoofing the DNS request and thus acting as a cache. Any suggestions/comments would be grateful. Thank you, JP

    Read the article

  • Windows Share permissions

    - by Armando
    I have a SQL/File server that I am replicating a File Share and SQL instance, using ArcServer RHA, to a Replica server. Everything seems to work as far as the replication of the SLQ instance and Share is concerned. When I fail over to the Replica server the DNS Host A record is modified to point to the Replica Server IP Address so if I do an NSLOOKUP on ServerA it then points to the IP Address of ServerB. Ans since the SQL instance is named the same I can still map my ODBC connections to ServerA and I can still make a SQL connection. When I try to do a \ServerA\Share I get an error that says I do not have permissions to the Share. I think this is because it uses keberose authentication and the Share is tied to the actual sever host name. I have tried puting in a CNAME and pointing it to ServerA and Disabling Strict Name Checking on ServerB as well as adding the CNAME to the OptionalNames in the registry but I am still getting the error when I have the ServerA powered off. Is there a way to reset the Authentication of the Share to use the DNS Cname?

    Read the article

< Previous Page | 232 233 234 235 236 237 238 239 240 241 242 243  | Next Page >