Search Results

Search found 120608 results on 4825 pages for 'code access security'.

Page 237/4825 | < Previous Page | 233 234 235 236 237 238 239 240 241 242 243 244  | Next Page >

  • Can't access server sound card when vnc'd into ubuntu server

    - by Corey Kennedy
    I've set up my ubunutu 10 server with xfce, nxserver, and now tightvncserver so that I can control it remotely from my Windows 7 laptop. NX is working fine for remote access, but when I run (for example) exaile, no sound will be sent through the server's sound card. I installed tightvncserver and connected, but ran into the same problem. Exaile opens, sound isn't muted, I can see that sound cards are installed (via cat /proc/asound/cards), but I can't seem to get the remote sessions to access the server's sound card. Also, just to confirm that the sound card was working I hooked up a montior/keyboard to the server and opened a local xfce session. That worked fine. While I had the local session running, I was also able to open a remote session with NXClient and start exaile - which then successfully piped sound to the local card. After disconnecting the monitor/keyboard and moving the box back to its normal spot, though, I was not able to play sound via either an NX or VNC session. Does anyone have any suggestions? Surely it's possible to configure my remote sessions to pipe sound to the server's sound card, right? Or at least get xfce up and running without a monitor or keyboard but with access to the sound card so I can VNC into it? Thanks!

    Read the article

  • Can't access site internally, but DNS works

    - by BloodyIron
    1) I have apache2 running a vhost for a website. 2) This apache2 instance is already successfuly setup for other websites on it to be accessible internally and externally. 3) I am using an internal bind9 server to resolve the new website's domain internally to the private IP. This bind9 server is not public facing, nor is it the master server on the internet. 4) The DNS internally resolves to the right IP. 5) Firefox reports "server not found". 6) I have copied the config almost identically to other configs that are known to work (adjusting for proper paths of course). In turn I have reloaded and restarted apache2 repeatedly. 7) I have an entry to forward .org .info .net alternative TLDs to .com in the vhost config for this domain, and my browser goes from .org to .com despite note #5. 8) /var/log/apache2/access.log shows when someone externally tries to access the site, but no activity is observed when someone tries to access internally. Changing the log level does not appear to improve the situation. 9) I am out of ideas, nothing appears to be wrong. Please help? To be explicit. Why is this new site unreachable internally? I would like to clarify on something, even though I have already outlined this. YES I know this system is in a private network. NO it is not going through a router. YES I am using an internal DNS server (bind9) to resolve, and YES it does resolve to the proper internal IP. YES other websites on the same server setup in the same way with internal resolution work right now and have done for a while. Everything for this domain is setup the same as the other working domains as far as I can tell. The other working domains are internally AND externally accessible. This domain I am working with is only currently externally accessible. When I go to it internally firefox tells me "Server not found".

    Read the article

  • One Windows Domain workstation can ping gateway but gets no internet access

    - by dindeman
    One of the (Windows XP SP3) workstations of our Windows Domain could not access internet anymore, this problem suddenly happened overnight. The domain controllers (there are three of them) are all running Windows Server 2008. First I compared the output of ipconfig /all on the faulty workstation with the output of a working workstation and it was just fine as it had always been. In particular the default gateway was correct and always remained pingable from the faulty workstation. I guessed that something was wrong with the DHCP service and I restarted the DHCP server service on all of our three DCs as well as the DHCP client service on the faulty workstation. This didn't solve the issue. I then thought of renewing the DHCP lease with ipconfig /release and ipconfig /renew and here is my first question: why did this never work? The same IP address (192.168.0.45) kept being assigned despite all my attempts to renew it (note that all our workstation are getting their TCP/IP automatically.) Even by leaving the domain and changing the computer name the same address was yet again obtained... Anyway I then proceeded to switch the TCP/IP configuration for that machine manually to another free valid IP address (192.168.0.41)... and then the internet access came back! I then cleared any traces of the previous IP in the DHCP leases list and in the DNS tables of our DCs and, after setting back the TCP/IP configuration to 'automatic', finally, the new lease would be granted (192.168.0.41) alongside with the internet access. My second question: what went suddenly wrong with the original IP address?

    Read the article

  • Why is my global security group being filtered out of my logon token?

    - by Jay Michaud
    While investigating the effects of filtered tokens on my file permissions, I noticed that one of my global security groups is being filtered in addition to the regular system-defined filtered groups. My Active Directory environment is a single-domain forest on the Windows Server 2003 functional level. I'll call the domain "mydomain.example.com". I am logged onto a Windows Server 2008 Enterprise Edition machine (not a domain controller) as a member of the "MYDOMAIN\Domain Admins" group and the "MYDOMAIN\MySecurityGroup" global security group (among others). When I run "whoami /groups" from an elevated command prompt, I see the full list of groups to which my account belongs as expected. When I run "whoami /groups" from a regular, non-elevated command prompt, I see the same list of groups, but the following groups are described as "Group used for deny only". BUILTIN\Administrators MYDOMAIN\Schema Admins MYDOMAIN\Offer Remote Assistance Helpers MYDOMAIN\MySecurityGroup Numbers 1 through 3 above are expected based on Microsoft documentation; number 4 is not. The "MYDOMAIN\MySecurityGroup" global security group is a group that I created. It contains three non-built-in global security groups, and these security groups contain only non-built-in user accounts. (That is, I created all of the accounts and groups that are members of the "MYDOMAIN\MySecurityGroup" global security group.) There are other, similar groups of which my account is a member that are not being filtered out of my logon token, and this group is not granted any specific user rights in the security settings of this computer or in Group Policy. What would cause this one group to be filtered out of my logon token?

    Read the article

  • IIS 6 Denies access to the default document

    - by Jim
    I've got Windows Server 2k3 with IIS6 hosting a couple ASP.NET MVC 2 applications (.NET 4), all in the Default Web Site. Most of them simply use Integrated authentication, but a couple use forms as well. All the applications work properly and are correctly accessible. The problem I'm trying to resolve is access to the default document. It is currently specified as index.htm. Both index.htm and the Default Web Site are configured to allow anonymous access (with none of the authenticated acces boxes checked). However, access is denied to the file. Accessing via server.domain.tld/ and server.domain.tld/index.htm both yield 401 errors. However, server.domain.tld/default.htm (file does not exist) properly returns a 404. If I alter the file security on index.htm to allow integrated authentication, then requesting /index.htm directly works properly for users with domain accounts, but anonymous users get a login prompt/401. How can I configure IIS to allow all users to view index.htm via server.domain.tld/?

    Read the article

  • Access an external SSH server through a restrictive proxy [on hold]

    - by Cyrille
    I'm a software developer. I wish to access my computer at home through SSH. For example, I sometime need to access my personal projects source code to check how I handled specific problems. Unfortunately, I currently work under an over-restrictive and anti-productive proxy that waste a hell of a lot of everyone's time (We often have to visit websites from our smartphones or use a web proxy to check very legitimates websites for answers, and don't get me started on other "security" overkill features we have to cope with...). Well, back to the subject, I can access my home computer from my phone (SSH, port 22 and 80 both redirected by router on port 22). It works, but it's quite uncomfortable. From my office computer, this is what I tried so far: export http_proxy=http://user:pass@proxyip:8080 echo "user:pass" > ~/.corkscrew-auth echo "ProxyCommand corkscrew proxyip 8080 %h %p /home/me/.corkscrew-auth" > ~/.ssh/config ssh 82.23.34.56 -l me -p 80 Proxy could not open connnection to 82.23.34.56: Forbidden ssh_exchange_identification: Connection closed by remote host (same without -p 80) Without corkscrew: ssh: connect to host 82.23.34.56 port 80: Connection timed out ssh: connect to host 82.23.34.56 port 22: Connection timed out Any other idea ?

    Read the article

  • apache access and error log written in same file

    - by user196075
    i have issue that access and error log are written in same file ! , the configuration in virtualhosts.conf as the following : <VirtualHost *:80> ServerName ************ ServerAdmin support@************8 DocumentRoot /var/www/html/*********.com ErrorLog /var/log/httpd/********/********.com_error_log CustomLog /var/log/httpd/********/********.com_access_log combined <Directory /var/www/html/***********.com> Options -Indexes FollowSymLinks AllowOverride All </Directory> </VirtualHost> as you see from the configuration each access and error logs should be save separately , but both logs are written in *.com_access_log , i have double check all permission , group and owner ... can't find anything wrong previous error in log file : [Thu Sep 19 14:15:02 2013] [error] [client 192.168.10.54] client denied by server configuration: /var/www/html/**********/show_has_offers.php i have tried to generate same error , i can find the hit in access log only as the following : 192.168.10.75 - - [24/Oct/2013:08:11:14 +0000] "GET /show_has_offers.php HTTP/1.1" 404 1586 "-" "Mozilla/5.0 (X11; Linux x86_64; rv:22.0) Gecko/20100101 Firefox/22.0" 0 17332 and nothing in error log !! Please advice ...

    Read the article

  • Windows 7 : access denied to ONE server from ONE computer

    - by Gregory MOUSSAT
    We have a domain served by some Windows 2003 servers. We have several Windows 7 Pro clients. ONE client computer can't acces ONE member Windows 2003 server. The other computers can acces every servers. And the same computer can access other servers. With explorer, the message says the account is no activated. With the command line, the message says the account is locked. With commande line : net use X: \\server\share --> several seconds delay, then error (says the account is locked) net use X: \\server\share /USER:current_username --> okay net use X: \\server\share /USER:domain_name\current_username --> okay From the same computer, the user can access other servers. From another computer, the same user can access any server, including the one denied from the original computer. Aleady done : unjoin then join the cilent from the domain. check the logs on the server : nothing about the failed attempts (?!) Is their any user mapping I'm not aware of ?

    Read the article

  • Problems restricting access using Apache

    - by Tola Odejayi
    I've set up XAMPP on a Windows 7 machine, and I want to restrict access to the htdocs folder to only requests from the local machine. C:\Xampp\htdocs is the web root folder. I have the following in my apache/conf/httpd.conf file: <Directory /> Options FollowSymLinks AllowOverride None Order deny,allow Deny from all </Directory> <Directory "C:/Xampp/htdocs"> Options Indexes FollowSymLinks Includes ExecCGI AllowOverride All order deny,allow deny from all allow from 127.0.0.1 allow from localhost </Directory> All my .htaccess files are blank. But when I navigate to the web root folder via a browser, I get the following message: Access forbidden! You don't have permission to access the requested directory. There is either no index document or the directory is read-protected. I tried adding the IP restrictions to the <Directory>...</Directory>, but it made no difference. What am I doing wrong here?

    Read the article

  • oracle access on vmware fusion

    - by gaudi_br
    Hello, I'm running snow leopard and I'm doing some development that requires some network knowledge. I've installed vmware fusion 3.0 and I've set up a virtual machine with windows 2003 server. I need to mimic the exact configuration of another server in the network, so I really need to run the versions I'll be mentioning here. Besides, I set up two network configurations on the VM: one NAT config (so that I can have internet access) and one host-only config (because I need to use another server's mac adress and my local area network might have a problem with it) From the installation of windows 2003, I then installed oracle 10.2.0.1. During the installation I received a warning about the primary ip-address of the system being dhcp assigned, but I ignored it (maybe it was a mistake)... Now, from experience, unless the DHCP assigned address changes, I should be able to access the guest system's database from the host system, so I went to safari and tried to access the oracle em. As it turns out, because my computer is on a company network, the company's DNS doesn't know about the virtual machine, unless of course I switch to a bridged network config. However, I don't want to do that because I don't to mix up the domains. So I guess the question is, how can I define my own dns or router, or whatever it is that I need to define so that whenever I try the guest system's ip address form the host, it will use the vmnet1 or vmnet8 interface define by vmware and bypass the dns configuration of my local area network. I'd also like to know what to do incase I want to change ip addresses on the guest machine without having oracle go haywire (I've noticed a few folders on the structure which are specific for the very first IP Address)... Any help would be appreciated. Thanks in advance.

    Read the article

  • Access denied when trying to open files/folders after reinstall [closed]

    - by user711532
    Possible Duplicate: Access Denied when saving a file in Windows 7 I installed Windows 7 fresh on a new machine. Now when I unarchive (winrar or 7z etc. ) to Program files (x86) (for example), access denied. Even if I copy a file to a folder I installed an app to it is still access denied. I checked the security, it looks like full control is given to the creator - this is weird as I never ran across this before (same version of Windows 7 - its just a fresh install after some new hardware). It is the same effect as if I was editing the hosts file, and you do not use "run as admin" you will not be able to save it, yo will have to save it somewhere else. This "file copy" issue I ran into is the same. I could change all these permissions, however this is something I never had to do before. I am the admin, why did the install, not give me "full control"? How can this be globally fixed. I cannot change the permissions - they are greyed out - so that is weird as well. If I was a standard reason, It would make sense, however, again, I am the admin.

    Read the article

  • Dealing with security on IPC remoting channel

    - by leppie
    Hi I am trying to run a service under a different user account from the application that will access the service via remoting. While under the same account everything is fine, but as soon as I use different accounts, I get an access denied error while trying to open the IPC port. Is there something I am missing, as I can't see from the MSDN docs what is supposed to be done. Thanks

    Read the article

  • code access security

    - by rkrauter
    Why do I need to Demand permission? Why can't it simply fail (commenting out the .Demand() call)? ref: http://support.microsoft.com/kb/315529 Thanks! try { // Demand the permission to access the C:\Temp folder. permFileIO.Demand(); resultText.Append("The demand for permission to access the C:\\Temp folder succeeded.\n\n"); }

    Read the article

  • Cursors 1 Sets 0

    - by GrumpyOldDBA
    I had an interesting experience with a database I essentially know nothing about. On the server is a database which stores session state, Microsoft provide the code/database with their dot net, so I'm told. Anyway this database has sat happily on the production server for the past 4 years I guess, we've finally made the upgrade to SQL 2008 and the ASPState database has also been upgraded. It seems most likely that the performance increase of our upgrade tipped the usage of this database into...(read more)

    Read the article

  • httpd.conf configuration - for internal/external access

    - by tom smith
    hey. after a lot of trail/error/research, i've decided to post here in the hopes that i can get clarification on what i've screwed up... i've got a situation where i have multiple servers behind a router/firewall. i want to be able to access the sites i have from an internal and external url/address, and get the same site. i have to use portforwarding on the router, so i need to be able to use proxyreverse to redirect the user to the approriate server, running the apache/web app... my setup the external urls joomla.gotdns.com forge.gotdns.com both of these point to my router's external ip address (67.168.2.2) (not really) the router forwards port 80 to my server lserver6 192.168.1.56 lserver6 - 192.168.1.56 lserver9 - 192.168.1.59 lserver6 - joomla app lserver9 - forge app i want to be able to have the httpd process (httpd.conf) configured on lserver6 to be able to allow external users accessing the system (foo.gotdns.com) be able to access the joomla app on lserver6 and the same for the forge app running on lserver9 at the same time, i would also like to be able to access the apps from the internal servers, so i'd need to be able to somehow configure the vhost setup/proxyreverse setup to handle the internal access... i've tried setting up multiple vhosts with no luck.. i've looked at the different examples online.. so there must be something subtle that i'm missing... the section of my httpd.conf file that deals with the vhost is below... if there's something else that's needed, let me know and i can post it as well.. thanks -tom ##joomla - file /etc/httpd/conf.d/joomla.conf Alias /joomla /var/www/html/joomla <Directory /var/www/html/joomla> </Directory> # Use name-based virtual hosting. #NameVirtualHost *:80 # NOTE: NameVirtualHost cannot be used without a port specifier # (e.g. :80) if mod_ssl is being used, due to the nature of the # SSL protocol. # VirtualHost example: # Almost any Apache directive may go into a VirtualHost container. # The first VirtualHost section is used for requests without a known # server name. #<VirtualHost *:80> # ServerAdmin [email protected] # DocumentRoot /www/docs/dummy-host.example.com # ServerName dummy-host.example.com # ErrorLog logs/dummy-host.example.com-error_log # CustomLog logs/dummy-host.example.com-access_log common #</VirtualHost> NameVirtualHost 192.168.1.56:80 <VirtualHost 192.168.1.56:80> #ServerAdmin [email protected] #DocumentRoot /var/www/html #ServerName lserver6.tmesa.com #ServerName fforge.tmesa.com ServerName fforge.gotdns.com:80 #ErrorLog logs/dummy-host.example.com-error_log #CustomLog logs/dummy-host.example.com-access_log common #ProxyRequests Off ProxyPass / http://192.168.1.81:80/ ProxyPassReverse / http://192.168.1.81:80/ </VirtualHost> <VirtualHost 192.168.1.56:80> #ServerAdmin [email protected] DocumentRoot /var/www/html/joomla #ServerName lserver6.tmesa.com #ServerName fforge.tmesa.com ServerName 192.168.1.56:80 #ErrorLog logs/dummy-host.example.com-error_log #CustomLog logs/dummy-host.example.com-access_log common #ProxyRequests Off </VirtualHost>

    Read the article

  • Multiple classes in a single .cs file - good or bad?

    - by Sergio
    Is it advisable to create multiple classes within a .cs file or should each .cs file have an individual class? For example: public class Items { public class Animal { } public class Person { } public class Object { } } Dodging the fact for a minute that this is a poor example of good architecture, is having more than a single class in a .cs file a code smell?

    Read the article

  • {smartassembly} software for code obfuscation

    {smartassembly} is a tool for ensuring that the source code your commercial .NET application isn't visible to anyone with .NET Reflector. Matteo, who writes for us about encryption in .NET, asked if he could write a review of {smartassembly} for Simple-Talk. Because we like the product too, and Red Gate Software had recently taken over the product, we were happy to agree.

    Read the article

  • {smartassembly} Software for Code Obfuscation

    {smartassembly} is a tool for ensuring that the source code your commercial .NET application isn't visible to anyone with .NET Reflector. Matteo Slaviero, who writes for us about encryption in .NET, asked if he could write a review of {smartassembly} for Simple-Talk. Because we like the product too, and Red Gate Software had recently taken it over, we were happy to agree. span.fullpost {display:none;}

    Read the article

  • Setting up Visual Studio 2010 to step into Microsoft .NET Source Code

    - by rajbk
    Using the Microsoft Symbol Server to obtain symbol debugging information is now much easier in VS 2010. Microsoft gives you access to their internet symbol server that contains symbol files for most of the .NET framework including the recently announced availability of MVC 2 Symbols.  SETUP In VS 2010 RTM, go to Tools –> Options –> Debugging –> General. Check “Enable .NET Framework source stepping” We get the following dialog box   This automatically disables “Enable My Code”   Go to Debugging –> Symbols and Check “Microsoft Symbol Servers”. You can selectively exclude modules if you want to.   You will get a warning dialog like so: Hitting OK will start the download process   The setup is complete. You are now ready to start debugging! DEBUGGING Add a break point to your application and run the application in debug mode (F5 shortcut for me). Go to your call stack when you hit the break point. Right click on a frame that is grayed out. Select “Load Symbols from” “Microsoft Symbol Servers”. VS will begin a one time download of that assembly. This assembly will be cached locally so you don’t have to wait for the download the next time you debug the app.   We get a one time license agreement dialog box You might see an error like the one below regarding different encoding (hopefully will be fixed).    Assemblies for which the symbols have been loaded are no longer grayed out. Double clicking on any entry in the call stack should now directly take you to the source code for that assembly. AFAIK, not all symbols are available on the MS symbol server. In cases like that you will see a tab like the one below and be given the option to “Show Disassembly”. Enjoy! Newsreel Announcer: Humiliated, Muntz vows a return to Paradise Falls and promises to capture the beast alive! Charles Muntz: [speaking to a large audience outside in the newsreel] I promise to capture the beast alive, and I will not come back until I do!

    Read the article

  • Python - cours intensif pour les scientifiques : Optimiser le code, par Rick Muller

    Bonjour,Je vous présente ce tutoriel traduit par Raphaël Seban intitulé : Python - cours intensif pour les scientifiques Partie 4 : Optimiser le code Pour de nombreux scientifiques, Python est LE langage de programmation par excellence, car il offre de grandes possibilités en analyse et modélisation de données scientifiques avec relativement peu de charge de travail en termes d'apprentissage, d'installation ou de temps de développement. C'est un langage que vous pouvez intégrer en...

    Read the article

  • rhythmbox plugin code for hot key not working

    - by Bunny Rabbit
    def activate(self,shell): self.shell = shell self.copy_selected() self.action = gtk.Action ('foo','bar','baz',None) self.activate_id = self.action.connect ('activate', self.call_bk_fn,self.shell) self.action_group = gtk.ActionGroup ('hot_key_action_group') self.action_group.add_action_with_accel (self.action, "<control>E") uim = shell.get_ui_manager () uim.insert_action_group (self.action_group, 0) uim.ensure_update () def call_bk_fn(): print('hello world') i am using the above code in a plugin for rhythmbox ,and here i am trying to register the key ctr+e so that the call_bk_fn gets called whenever the key combination is pressed , but its not working why is that so ?

    Read the article

  • APress Deal of the Day - 30/Nov/2011 - Moving to VB .NET Strategies, Concepts, and Code

    - by TATWORTH
    Today's $10 Deal of the day from APress at  is Dan Appleman's "Moving to VB .NET Strategies, Concepts, and Code"."Visual Basic guru Dan Appleman exposes the reality behind the VB .NET hype, and shows you how to evaluate this technology in the context of your specific problems."Considering the vast amount of VB6 still in use, this book from 2001 will be of immense help to all tasked with converting Vb6 to VB.NET or C#.

    Read the article

< Previous Page | 233 234 235 236 237 238 239 240 241 242 243 244  | Next Page >