Search Results

Search found 9758 results on 391 pages for 'wireless networking'.

Page 237/391 | < Previous Page | 233 234 235 236 237 238 239 240 241 242 243 244  | Next Page >

  • VPC on Windows 7 very slow network

    - by Shigg
    I have a Windows 2003 virtual machine which I use for website testing. I've just installed Windows 7 and am using the new version VPC (not xp mode). When I try to copy a file - I need to copy some big databases across - I get a file copy speed of about 20k per sec. Copying from one PC to another on the real network transfers files at 13mb per second. Any ideas what may be causing this? I've turned off differential network compression on win 7. The Virtual HD is on a seperate physical drive to the OS. Running Windows 7 64 bit on a dual xeon with 16gb ram and 10,000 rpm drives. Tried installing VPC 2007 but windows blocks it running saying its not compatable. Many thanks for any ideas.

    Read the article

  • Backup/Multihomed network connection

    - by J_P
    We have a couple locations that require 24/7 access to Internet and our current provider (AT&T) while mostly good is not always up. My concern would be if I go with another provider (for example Comcast) I'm going to be subject to the same down time if it's in the "last mile". I for the most part don't know where the failure points are on the ISP side but I would imagine the large majority are within the last mile. I'd looked at Mifi or similar solution but have concerns about bandwidth caps and overall speed. Any suggestions would be appreciated.

    Read the article

  • Am I supposed to assign the broadcast IP somewhere?

    - by pvieira
    This is a very basic question from a newbie point of view. I have a dedicated server at Hetzner running Windows 2008 R2. I bought a subnet of IP addresses to use in this server. They provided me a given range of IPs, incluind one Ip labeled as "Broadcast". I know how to assign those IPs to the NIC, but should I do something with the Broacast IP, like configure it somewhere on Windows? Or can I just ignore it and I'll be fine? This IP range will be used to host SSL sites.

    Read the article

  • ASUS WL-500gP v2 network between two local machines

    - by Epsiloncool
    I have two windows XP machines in my home networks, connected with ASUS WL-500gp V2 which also used as internet router. Problem is: while I have both computers normally goes to internet (used DHCP, static routes is ON, routing table is empty, operation mode is Home Gateway). I see both computers listed on the Network Neighborhood on 1st computer (wired to router), can enter to my own computer, but can not enter to other. I see only one computer (2nd) on the Network Neighborhood on 2nd computer (connected thru Wi-Fi), can enter to itself, getting error when trying to enter 1st computer address in address line (like \My1stComp). What is the problem? I totally crazy founding problem about 3 months.

    Read the article

  • What are the methods of separating network spaces in a LAN?

    - by dash17291
    Please detail me the methods. My thoughts: put the servers in separate (sub)networks the servers are forced to go through the firewall but no NAT is required assign more IP addresses to the internal interface of the server choosing gateway addresses from the clients and servers IP address ranges split DNS Netfilter/{iptables, ipset} could be heavily involved, I'm talking about Linux servers. See for example: Destination NAT Onto the Same Network from internal clients Please do not explain what is NAT or DNS. This is a theoretical question, but my poor English knowledge prevent me to describe it in a fancy fashion.

    Read the article

  • Separate 2 networks with 1 Windows Server

    - by SamuGG
    The situation is: I have 1 router 192.168.1.1, 1 switch, 1 windows server and a basic LAN of devices accessing it. I need to split into 2 separate LANs with full Internet access each, but isolated from each other. Given that, the server is a Windows Server 2008 R2 with 2 NICs: NIC1: 192.168.1.2 NIC2: 192.168.2.2 The router has no dhcp configuration. Please, can anyone explain gracefully, step by step, what do I need to do? What would be the 2 NICs full configuration? What services do I need to install? I don't want devices on either network to see devices on the other network, they must be completely separate. I guess I'm missing the routing procedure step, but I have no idea how is that done. For example: tell the server that devices with gateway 192.168.2.2 must send traffic for internet to 192.168.1.1 router. Thanks in advance.

    Read the article

  • ubuntu 12.04 kvm virtual server network setup, can't get the machine to be connectable

    - by xyious
    I have worked on my Ubuntu Server host for weeks now and I just can not manage to get the virtual machines into the network.... here's what I need to do: I need to be able to create virtual machines that have IP addresses that can be reached from the outside (192.168 network). I need to be able to connect to the virtual machines through ssh, ftp, http and preferably https, anything else doesn't matter that much. So far everything seems simple enough and I have a lot of leeway in terms of IP address range and server/client configuration. I have the option of taking part of a /24 net as most IPs aren't used, and if it's absolutely necessary I have the option of creating a new /24 subnet. Also have the option of reformatting and reinstalling OS on the host and recreating the virtual machines as nothing has been done other than trying to get virtual machines to work. I would prefer if the virtual machines were just part of the normal network which would be 192.168.5.0/24. The host machine has 2 network cards so I don't even necessarily need the Host to be connectable in the same /24 network. I have tried (I think) just about everything from about 5 different tutorials on bridging (giving br0 the same IP that eth0 used to have (Host is able to connect to VM and vice versa, VM doesn't have outside network access), having eth0 set up like it always was and having br0 have a different IP (same as above), NAT with port forwarding (which I would have preferred not to use but will if it works), turning off one of the hosts network cards and just using one of them, different subnets.... etc. I do know my way around iptables fairly well.... Host is 64bit Ubuntu Server 12.04, using libvirt/kvm. edits: Local network is 192.168.5.0/24, host has static ip 192.168.5.254, GW .5.1 which is also nameserver. We have a second Local network at 192.168.10.0/24 with .10.1 GW, but both hosts and VMs were supposed to go into the .5 subnet. The .10 subnet isn't required, but it wouldn't be horrible if the Host were only accessible in the .10 subnet.

    Read the article

  • How to attach multiple ipv6 ips to eth1 on debian

    - by Noodles
    I've just got a new server with native ipv6. I want to attach multiple ipv6 ips to eth1, but the only way I can see to do so is to attach them individually: i.e. address 2607:f0d0:xxxx:xxxx::2 address 2607:f0d0:xxxx:xxxx::3 address 2607:f0d0:xxxx:xxxx::4 Is it possible to bind whole subnets of ipv6 to a single network interface on debian? My server host tells me I have 18,446,744,073,709,551,616 ipv6 addresses for that server, surely it gets to be a nightmare to manage if they all have to bound individually (plus ifconfig would look messy). Does anyone have a solution?

    Read the article

  • Protocol (or service publish/discovery) to detect devices in network

    - by Gobliins
    we connect some embedded devices in a network. What i am looking for now, is a way to find the devices IP and identify them. We work with Windows PC´s and i am about to write a C# tool that should do this. I thought about send a udp broadcast and in the ack i.e. is the device´s ip, which would mean the device needs a daemon runnig to assign an ip itself. Running a service (like a printer) on the device, and on the PC just lookup for the service. I read about some things like apipa, zeroconf, ipv4 local link, bonjour, dns-sd, mdns, bonjour; They can automatically assign ip´s and publish services in a network. My Question is, can someone recommend me what would be good for my task? -The protocol or Service should be low on ressource (memory/cpu usage) use. -Are there some standard protocolls to use? -Is DNS a good idea or would it be to ressource consumpting just for finding a device´s IP? -Should also work when no dhcp servers are around. edit: To clarify a bit: The IP configuration is automatic. The problem to focus is how to tell the PC which IP in the network (or a direct connection in this vase there would only be one) belongs to the device (identity).

    Read the article

  • Static IP on Wifi at work and dynamic at home?

    - by Jason Shultz
    I need the laptops at my office to have a static IP for security purposes and identification. However, some employees take their laptops home in the evening. If I have the wifi config set to use a static IP, how can they have a dynamic IP at home? the laptops are using Windows Vista and Windows 7.

    Read the article

  • NIC going to sleep on Ubuntu Server 10.04

    - by user43390
    When I leave my server idle for about 10 minutes the network will stop responding to outside connections. If I get on the server and attempt to use the network(ping google for example) there will be a delay for a few seconds and then it works. After this incoming connections work again until I leave it idle again. Why does this happen and how can I fix it?

    Read the article

  • Using a second Wifi Router (in order to use a LAN port)

    - by Sledge81
    Problem: Connecting a TV decoder via Internet. It doesn't have inbuilt wifi so wired LAN is the only option. I bought a second Wifi Router so I could use its LAN port to create a wired internet connection to my decoder. What I want to achieve: The second Wifi Router should basically pick up the signal from the main wifi router. I would then use the LAN port to connect (with a wire) to the TV decoder. In other words have my secondary Wifi Router act as an access point, which will enable me to use a wired LAN connection to the decoder. What i've done so far: Connected the second Wifi Router to my laptop via the LAN ports. Access 192.168.1.1 and went into my second router. 1) SSID set to the same one as the main Wifi Router 2) Tried disabling DHCP and enabling DHCP (with the DNS and default gateway configured the same as the main router). When I check my network connections, I see the LAN connection too but it says 'Not connected to the internet' while the Wifi (main router) shows connected. Can someone please advise on how to use my second Wifi Router to connect to the main Wifi Router (and thus the Internet). Thanks. main wifi router: Zyxel secondary wifi router: TP Link

    Read the article

  • Setting up Relays in Windows

    - by Auditor
    I'm trying to setup a pivoting relay with netcat on Windows, replicating a scenario easily possible by using pipes in Linux. Assume machine A can route to machine B and machine B can route to machine C. If machine A needs to route to machine C, we can setup a relay on machine B which can pivot data back and forth for us using command redirectors and spl filetype pipe. Assume: machine C has nc -nlvp 3306 -e cmd.exe machine A has nc -nlvp 80 IF machine B was Linux we could have done mkfifo pipe nc -nv 127.0.0.1 80 0<pipe | nc -nv 127.0.0.1 3306 1>pipe so on machine B if we do nc -nv 127.0.0.1 80 0<&4 | nc -nv 127.0.0.1 3306 1>&4 Per this site, I should be able to achieve what I can with Linux, but unfortunately it is not working.

    Read the article

  • Network Performance issue

    - by qubemarker
    We have three Ubuntu 10.04 servers. One server is a storage server and the other two servers are configured as clients. The storage server has a good amount of capacity and it is integrated with windows Active directory server for Authentication. I am uploading some video files from both clients to the server and when I am uploading data from any one client alone I get about 26 MB/s data transfer rate. When I upload data from both the clients simultaneously I am only getting about 8 MB/s from each client. I have gigabit ethernet cards in all of the servers and a L2 Managed gigabit switch for connectivity. I don’t know why the data transfer rate is decreasing so much in simultaneous read and write. I have tried all of the TCP stack related settings suggested here. Can any assist with getting better read/write performance out of this setup? Any help is appreciated.

    Read the article

  • TCP Sessions and IP Changes

    - by Kyle Brandt
    What happens to a TCP session when the IP of a client changes? I did a simple test of having netcat listen on a port, and connecting to that port from a client machine. I then changed the IP of the client while that nc session was open and sent some data, no data was received by server after changing the IP. I know they are different layers, but does TCP use IPs for part of how it distinguishes sessions? Does my example not work because of how the application handles it, or is this not working because of something happening at TCP/IP/Ethernet layers? Does this depend on the OS implementation? ( I am most interested in Linux at the moment)

    Read the article

  • How can Icheck how much data has been transfered in a particular remote computer in my LAN?

    - by oDx
    I am the system administrator. I am suspecting some unwanted data transfers in some of the computers under my lan. This also effects the overall performance of the network. Is there anyway by which i can check the transfered data over a particular interval. I am not supposed to install any applications on any other computers than mine. I have the router access. I can use tools like ettercap dsniff wireshark etc.

    Read the article

  • Is this one network or two networks?

    - by colemik
    I have this simple question and really don't know the answer. Does the drawing below show one network or two networks? This is a question about the definition of a network from the OSI / TCP/IP model point of view: From one point of view, those are two L2 networks connected with a bridge. From another point of view, this is one L3 network, that can have a common L3 address space (like 10.1.1.0). PS If this question is too dumb, please move it to Superuser.

    Read the article

  • Why is iTunes using so much data?

    - by George
    I've been told by my ISP I'm using too much bandwidth so after using Activity Monitor to see that I'm using ~2GB a day I've used the nettop command line utility to work out where. Turns out it's iTunes. I don't use it for downloading/streaming music (other than podcasts of which I definitely don't have 2GB of new ones a day) or movies. What is iTunes doing? This is on a late 2009 MacBook running Lion 10.7.5 with iTunes version 10.7

    Read the article

  • Combine multiple network interfaces to connect to a dedicated server

    - by Dženis Macanovic
    this is an underpaid employee writing, who's apparently responsible for all the IT stuff in a very small (non-IT) company. Today said company got a bunch of PCs/workstations, a switch, a computer that's supposed to be used as a router, two DSL connections (each 16 MBit/s downstream and 1 MBit/s upstream) and a dedicated server which is hosted and managed professionally by a larger local company with some decent connection speed (1 GBit/s both directions if I'm not mistaken). This is what I've set up (note I'm not making use of the second DSL connection at all)... ETH0 ETH1 [ SWITCH ]---[LINUX DEBIAN ROUTER]---[DSL MODEM 1]---[INTERNET] | | | PC1 | | PC2 | ... ... when my boss asked me, if it was somehow possible to get 32 MBit/s downstream and 2 MBit/s upstream. At that time I replied "no" without thinking too much about it. Now I've just had the following idea... ETH1 ETH0 ETH0 ,---[DSL MODEM 1 (NON-STATIC IP)]---, ,---, ETH0 [ SWITCH ]---[LINUX DEBIAN ROUTER] [INTERNET] [LINUX DEBIAN SERVER]---[INTERNET] | | | '---[ DSL MODEM 2 (STATIC IP) ]---' '---' PC1 | | ETH2 ETH0 PC2 | ... ... but I have absolutely no clue how to implement that. Would that even be possible? What would the masquerading rules look like on the router? What about the server? I didn't find anything on the internet, mainly because I couldn't come up with any good keywords to search for to begin with. English obviously isn't my first language. Thanks in advance for your time!

    Read the article

  • /etc/hosts file for a multi-homed, multi-domain machine?

    - by threecheeseopera
    I have a server (debian) with two network interfaces that I would like to host multiple services and domains on; it is not entirely clear to me how the hosts file should be set up. Example: eth0, bound to WAN interface 1.2.3.4: mail.example.com www.example.com eth0:1, bound to WAN interface 1.2.3.5: www.other-domain.com eth1, bound to LAN 192.168.1.123: some-clever-hostname What should my hosts file look like? (including localhost,localhost.localdomain, etc.) Should I use DNS for some of these entries? Which ones? Thanks!

    Read the article

  • How to disable wifi usage on Windows 7

    - by Eric
    On a laptop, we currently use LAN(RJ45) connection to access internet. But from time to time, on startup, the laptop "catch" an unsecured wifi hotspot from one of my neighbors, so we would like windows 7 to NOT choose any wifi network : how this can be done ?

    Read the article

  • Cisco 861 Router forces one-to-one NAT

    - by Slurpee
    I have a cisco 861 router that only allows one-to-one NATs in order to access the Internet. I would like for computers to get an address via DHCP from this router, and be able to access the Internet without needing to set a static NAT to one of my public IPs. What is wrong with the configuration? I have a basic understanding of the IOS CLI, most of the configuration file (edited for content) was created by my company's long gone Senior Network Engineer.

    Read the article

  • node.js server not running

    - by CMDadabo
    I am trying to learn node.js, but I'm having trouble getting the simple server to run on localhost:8888. Here is the code for server.js: var http = require("http"); http.createServer(function(request, response) { response.writeHead(200, {"Content-Type": "text/plain"}); response.write("Hello World"); response.end(); }).listen(8888); server.js runs without errors, and trying netstat -an | grep 8888 from terminal returns tcp4 0 0 *.8888 *.* LISTEN However, when I go to localhost:8888 in a browser, it says that it cannot be found. I've looked at all the related questions, and nothing has worked so far. I've tried different ports, etc. I know that my router blocks incoming traffic on port 8888, but shouldn't that not matter if I'm trying to access it locally? I've run tomcat servers on this port before, for example. Thanks so much for your help! node.js version: v0.6.15 OS: Mac OS 10.6.8

    Read the article

< Previous Page | 233 234 235 236 237 238 239 240 241 242 243 244  | Next Page >