Search Results

Search found 9557 results on 383 pages for 'x86 64'.

Page 238/383 | < Previous Page | 234 235 236 237 238 239 240 241 242 243 244 245  | Next Page >

• Dim (NEARLY blank) laptop screen, secondary screen works - why?

  - by LIttle Ancient Forest Kami

  My laptop screen is (almost) black while my secondary screen is fine. I believe it to be backlight / brightness related. Problem description it starts when I start the laptop system loads and works fine, just screen has problems I can see the screen though very faintly / dimly - it's hard to see anything which ain't very white e.g. starting screen has big Thinkpad logo in white, large font - I can see it, though very dimly second screen works very well Official backligtht debugging: using acpi setting as prescribed there for Thinkpads didn't help I can see an entry in /sys/class/backlight/ and it changes when I press hotkeys for brightness (current backlight power for instance goes up or down) acpi-off didn't helpm neither did acpi_backlight=vendor Hardware data Laptop is Thinkpad Edge with glossy screen. 4 processors, 2 cores, exemplary CPU data from cat /proc/cpuinfo reports Genuine Intel i5 (M 480 @ 2.67GHz). OS is Ubuntu Lucid, 10.04 LTS, 64-bit, with Linux generic kernel (2.6.32-44) and GNOME 2.32.2 (though I doubt there lies the problem). $ lspci | grep VGA 01:00.0 VGA compatible controller: ATI Technologies Inc M92 [Mobility Radeon HD 4500 Series] $ lshw -C display *-display description: VGA compatible controller product: M92 [Mobility Radeon HD 4500 Series] vendor: ATI Technologies Inc physical id: 0 bus info: pci@0000:01:00.0 version: 00 width: 32 bits clock: 33MHz capabilities: pm pciexpress msi bus_master cap_list rom configuration: driver=radeon latency=0 resources: irq:33 memory:c0000000-dfffffff(prefetchable) ioport:2000(size=256) memory:f0300000-f030ffff memory:f0320000-f033ffff(prefetchable) Driver I was NOT running any proprietary drivers, just checked with "Hardware drivers". There is one for ATI that is suggested there, though I didn't need it so far. UPDATE: changing the driver to proprietary one (ATI/AMD FGLRX) didn't help. Tried and failed Resetting / running on power or battery / charging / getting rid of static electricity / warming up *doesn't help* This is NOT a blank-screen problem, at least it isn't following official Ubuntu black-screen diagnostics - I can see my screen, though barely. What I will try next: - check last updates I've made - IIRC I am running on nomodeset already, but will verify this Any ideas how to proceed best? What is most probable cause?

  Read the article

• VirtualBox 4.0.10 is now available for download

  - by user12611829

  VirtualBox 4.0.10 has been released and is now available for download. You can get binaries for Windows, OS X (Intel Mac), Linux and Solaris hosts at http://www.virtualbox.org/wiki/Downloads The full changelog can be found here. The high points for the 4.0.10 maintenance release include .... GUI: fixed disappearing settings widgets on KDE hosts (bug #6809) Storage: fixed hang under rare circumstances with flat VMDK images Storage: a saved VM could not be restored under certain circumstances after the host kernel was updated Storage: refuse to create a medium with an invalid variant Snapshots: none of the hard disk attachments must be attached to another VM in normal mode when creating a snapshot USB: fixed occasional VM hangs with SMP guests USB: proper device detection on RHEL/OEL/CentOS 5 guests ACPI: force the ACPI timer to return monotonic values for improve behavior with SMP Linux guests RDP: fixed screen corruption under rare circumstances rdesktop-vrdp: updated to version 1.7.0 OVF: under rare circumstances some data at the end of a VMDK file was not written during export Mac OS X hosts: Lion fixes Mac OS X hosts: GNOME 3 fix Linux hosts: fixed VT-x detection on Linux 3.0 hosts Linux hosts: fixed Python 2.7 bindings in the universal Linux binaries Windows hosts: fixed leak of thread and process handles Windows Additions: fixed bug when determining the extended version of the Guest Additions Solaris Additions: fixed installation to 64-bit Solaris 10u9 guests Linux Additions: RHEL6.1/OL6.1 compile fix Linux Additions: fixed a memory leak during VBoxManage guestcontrol execute Technocrati Tags: Sun Virtualization VirtualBox var sc_project=1193495; var sc_invisible=1; var sc_security="a46f6831";

  Read the article

• Ubuntu 12.04 still slow at mounting internal filesystem

  - by Matthew Goson

  I'm using Toshiba laptop with this configuration: - CPU: Core i5, 2.4GHz - RAM: 4GB - Graphics card: Intel - Hard disk: 500GB SATA I installed Ubuntu 12.04 64bit and got the same issue with this guy Very slow boot due to mounting filesytem, I tried all suggestions there but the slow boot issue still here. Here's a part of my dmesg: [ 2.041015] usbhid: USB HID core driver [ 2.101378] usb 1-1.6: new full-speed USB device number 5 using ehci_hcd [ 2.137980] atl1c 0000:04:00.0: version 1.0.1.0-NAPI [ 2.779080] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null) [ 22.822597] udevd[381]: starting version 175 [ 22.837954] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 22.850837] lp: driver loaded but no devices found [ 23.003822] Adding 7079096k swap on /dev/sda7. Priority:-1 extents:1 across:7079096k [ 23.407915] mei: module is from the staging directory, the quality is unknown, you have been warned. [ 23.408153] mei 0000:00:16.0: PCI->APIC IRQ transform: INT A -> IRQ 16 [ 23.408160] mei 0000:00:16.0: setting latency timer to 64 [ 23.408211] mei 0000:00:16.0: irq 44 for MSI/MSI-X [ 23.433196] [drm] Initialized drm 1.1.0 20060810 Additional information: my sda1 is a primary NTFS partition, sda2 is a primary ext4 partition which I installed Ubuntu onto. Other partitions are inside an extended partition.

  Read the article

• Logging Output of Azure Startup Tasks to the Event Log

  - by Your DisplayName here!

  This can come in handy when troubleshooting: using System; using System.Diagnostics; using System.Text;   namespace Thinktecture.Azure {     class Program     {         static EventLog _eventLog = new EventLog("Application", ".", "StartupTaskShell");         static StringBuilder _out = new StringBuilder(64);         static StringBuilder _err = new StringBuilder(64);           static int Main(string[] args)         {             if (args.Length != 1)             {                 Console.WriteLine("Invalid arguments: " + String.Join(", ", args));                 _eventLog.WriteEntry("Invalid arguments: " + String.Join(", ", args));                                 return -1;             }               var task = args[0];               ProcessStartInfo info = new ProcessStartInfo()             {                 FileName = task,                 WorkingDirectory = Environment.CurrentDirectory,                 UseShellExecute = false,                 ErrorDialog = false,                 CreateNoWindow = true,                 RedirectStandardOutput = true,                 RedirectStandardError = true             };               var process = new Process();             process.StartInfo = info;               process.OutputDataReceived += (s, e) =>                 {                     if (e.Data != null)                     {                         _out.AppendLine(e.Data);                     }                 };             process.ErrorDataReceived += (s, e) =>                 {                     if (e.Data != null)                     {                         _err.AppendLine(e.Data);                     }                 };               process.Start();             process.BeginOutputReadLine();             process.BeginErrorReadLine();             process.WaitForExit();               var outString = _out.ToString();             var errString = _err.ToString();               if (!string.IsNullOrWhiteSpace(outString))             {                 outString = String.Format("Standard Out for {0}\n\n{1}", task, outString);                 _eventLog.WriteEntry(outString, EventLogEntryType.Information);             }               if (!string.IsNullOrWhiteSpace(errString))             {                 errString = String.Format("Standard Err for {0}\n\n{1}", task, errString);                 _eventLog.WriteEntry(errString, EventLogEntryType.Error);             }               return 0;         }     } } You then wrap your startup tasks with the StartupTaskShell and you’ll be able to see stdout and stderr in the application event log.

  Read the article

• cannot boot ubuntu 13.10 with my usb, Can i change the kernal on my laptop to run it?

  - by Carlos Dunick

  Currently i am running 12.04 and looking for an upgrade to 13.10 I first tried a bootable 64bit usb and failed. With the message saying "Kernal requires an x86-64 CPU but only detected an I686 CPU Unable to boot please use a kernal appropriate for your CPU" then tried 32bit and same message came up. Is this due to my laptop simply being to slow? or can/should i change the kernal somehow? Acer Aspire 5710z Intel Pentium dual core processor, 1.73Ghz, 533 MHz FSB, 1 MB L2 cache. 2GB DDR2 lspci 00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express Memory Controller Hub (rev 03) 00:02.0 VGA compatible controller: Intel Corporation Mobile 945GM/GMS, 943/940GML Express Integrated Graphics Controller (rev 03) 00:02.1 Display controller: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller (rev 03) 00:1b.0 Audio device: Intel Corporation NM10/ICH7 Family High Definition Audio Controller (rev 02) 00:1c.0 PCI bridge: Intel Corporation NM10/ICH7 Family PCI Express Port 1 (rev 02) 00:1c.2 PCI bridge: Intel Corporation NM10/ICH7 Family PCI Express Port 3 (rev 02) 00:1c.3 PCI bridge: Intel Corporation NM10/ICH7 Family PCI Express Port 4 (rev 02) 00:1d.0 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #1 (rev 02) 00:1d.1 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #2 (rev 02) 00:1d.2 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #3 (rev 02) 00:1d.3 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #4 (rev 02) 00:1d.7 USB controller: Intel Corporation NM10/ICH7 Family USB2 EHCI Controller (rev 02) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2) 00:1f.0 ISA bridge: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge (rev 02) 00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller (rev 02) 00:1f.2 SATA controller: Intel Corporation 82801GBM/GHM (ICH7-M Family) SATA Controller [AHCI mode] (rev 02) 00:1f.3 SMBus: Intel Corporation NM10/ICH7 Family SMBus Controller (rev 02) 04:00.0 Ethernet controller: Broadcom Corporation NetLink BCM5787M Gigabit Ethernet PCI Express (rev 02) 05:00.0 Network controller: Broadcom Corporation BCM4311 802.11b/g WLAN (rev 01) 06:00.0 FLASH memory: ENE Technology Inc ENE PCI Memory Stick Card Reader Controller 06:00.1 SD Host controller: ENE Technology Inc ENE PCI SmartMedia / xD Card Reader Controller 06:00.2 FLASH memory: ENE Technology Inc Memory Stick Card Reader Controller 06:00.3 FLASH memory: ENE Technology Inc ENE PCI Secure Digital / MMC Card Reader Controller

  Read the article

• Random touchpad and keyboard freezes on new 10.10 installation

  - by ancaleth

  My touchpad and keyboard freeze up on my newly installed Ubuntu 10.10. I was using Ubuntu 10.4 via wubi before on this Laptop where this problem never occurred. (I did not migrate wubi or upgrade to 10.10, it's a fresh start. 64-bit on Dell Studio, plenty of RAM, plenty of free space on partition etc.) I can't say there is a pattern yet, once it happened during the download of packages with the Update Manager, once it was just using Firefox, no other program running. I was forced to shut down manually. In between these crashes the laptop was booted once, updates were installed etc., firefox was used and there weren't any problems. Both crashes should be in the attached kern.log and I noticed there were some error problems before the last crash (at the end, obviously). It seems the wireless was experiencing problems. This wasn't noticed on the user end, since the touchpad + keyboard were already frozen. kern.log: http://paste.ubuntu.com/552617/ How can the freezes be fixed?

  Read the article

• HP DV6 connects but no internet

  - by Frank Barcenas

  I have a Hewlett Packard DV6. I connected to the access point. I receive an IP address/default gateway/DNS,etc(DHCP). I cannot ping my gateway. DNS lookups fails. There is just no connectivity. My driver is listed as being IWLWIFI. An lspci shows my card to be a Realtek RTL8101E/RTL8102E. I can't ping myself from another computer. eth0 Link encap:Ethernet HWaddr c8:0a:a9:0c:a7:45 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:41 Base address:0xe000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:561 errors:0 dropped:0 overruns:0 frame:0 TX packets:561 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:42164 (42.1 KB) TX bytes:42164 (42.1 KB) wlan0 Link encap:Ethernet HWaddr 00:26:c7:04:97:c0 inet addr:192.168.1.109 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::226:c7ff:fe04:97c0/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:12 errors:0 dropped:0 overruns:0 frame:0 TX packets:71 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2035 (2.0 KB) TX bytes:12371 (12.3 KB)

  Read the article

• Ubuntu 14.04 install fails with Via S3 UniChrome Pro graphics

  - by WizardNo.7

  I am trying to install Ubuntu 14.04 on a Fujitsu Siemens Amilo Pro laptop(it's quite old yes, has about 30GB Hard Drive and I think 192mb of RAM) which currently has Windows XP installed (which I'd like to keep for the time being). I have downloaded the 32-bit Desktop ISO and used unetbootin to create a Live USB for this laptop. When I boot from USB, I arrive at the unetbootin Grey and Blue menu and pick either "Try Ubuntu without installing", or "Install Ubuntu". The menu goes away and an Ubuntu loadscreen showing UBUNTU and four dots which progressively change between white and orange. At about the second color changing cycle a white underscore symbol appears next to the fourth dot and flickers. There is some leftover text from the kernel boot still visible, but there is no graphical desktop. After this I have to hard reboot or shut-down. $ lshw -c video *-display UNCLAIMED description: VGA compatible controller product: CN700/P4M800 Pro/P4M800 CE/VN800 Graphics [S3 UniChrome Pro] Vendor: VIA Technologies, Inc. physical id: 0 bus info: pci@0000:01:00.0 version: 01 width: 32 bits clock: 66MHz capabilities: pm agp agp-2.0 vga_controller bus_master cap_list configuration: latency=64 mingnt=2 resources: memory:f0000000-f3ffffff memory:d1000000-d1ffffff

  Read the article

• 12.10 Wireless networking

  - by user108594

  I downloaded ubuntu 12.10 using WUBI and cannot connect to the internet. I removed it and downloaded ubuntu 12.04 still cannot connect. This I assume rules out the program being the problem. I reinstalled 12.10. When loaded I get the same message W/red (x) stating Internet not connected. I went to the Settings drop down box and it does not reveal the network list but (enable networking has a ck mark). Am running a HP Laptop with a w/7/64 OS that has a kill switch that indicates (orangeno connection) I downloaded 12.10 on my desktop (on the same network) and everything OK. I tried to follow the instructions in the help menu but got lost and confused . Sincerely Dan Additional Info per request Broadcom 802.11b/g Wlan Internal pc [hp laptop] P.S. I've been out of town for about a month. TKS for your gitback I did install 12.10 via cd and everything ok,but retried alongside 7 and unable to connect to internet,also took laptop and hard wired using ethernet cable and everything ok. stumped again and running out of ideas!!!

  Read the article

• How do I connect to a wireless network?

  - by Keith Groben

  I just installed 10.10 x64 and cannot even find my wireless network let alone connect to it. I've searched all over SE and Ubuntu forums and cannot find out how to do this simple thing. Can some one please give me the answer? It is plugged in right now and is 100% updated. It is a Desktop with wireless card. 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no Here's the output: *-network DISABLED description: Wireless interface product: RT2860 vendor: RaLink physical id: 0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 00 serial: 70:1a:04:f4:de:e9 width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=rt2800pci driverversion=2.6.35-27-generic firmware=N/A latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:fcff0000-fcffffff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 03 serial: 00:23:54:fd:c2:32 size: 100MB/s capacity: 1GB/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full ip=192.168.1.14 latency=0 link=yes multicast=yes port=MII speed=100MB/s resources: irq:44 ioport:d800(size=256) memory:fceff000-fcefffff memory:ddffc000-ddffffff memory:fcec0000-fcedffff === Update === I have discovered that this is a know issue with the rt2860. I have been following step by step the instructions found here: http://www.ctbarker.info/2010/05/ubuntu-1004-wireless-chipsets-and-wpa.html I decided to stat over because I was getting stuck on step 5: 'sudo rmmod rt2860sta' is was giving me this problem: 'ERROR: Module rt2860sta does not exist in /proc/modules' Since I started over I cannot even get past step 5 'sudo make' I get this: 'make: * No targets specified and no makefile found. Stop.' I am lost. Any help would be appreciated.

  Read the article

• Is it viable to make a port from a C++ application to Java through LLVM

  - by Javier Mr

  how viable is it to port a C++ application to Java bytecode using LLVM (I guess LLJVM)? The thing is that we currently have a process written in C++ but a new client has made mandatory to been able to run the program in a multiplatform way, using the Java Virtual Machine with obviously no native code (no JNI). The idea is to be able to take the generated jar and copy then to different systems (Linux, Win, 32 bits - 64 bits) and it should just work. Looking around looks like it is possible to compile C++ to LLVM IR code and then that code to java bytecode. There is no need of the generated code to be readable. I have test a bit with similar things using emscripten, this takes C++ code and compile it to JavaScript. The result is valid JS but totally unreadable (looks like assambler). Does anybody done a port of an application from C++ to Java bytecode using this tecnique? What problems could we face? Is a valid approach for production code? Note: I am aware that currently we have some non standard C++ and close source libraries, we are looking to removing this non standard code and all close source libraries and use Free Libre Open Source Software, so lets suppose all code is standard C++ code with all code available at compile time. Note: It is not an option to write portable C++ code and then compile it to the desired target platform, the compiled program must be mltiplatform thus the use of JVM (right now we are not looking in similar solutions but Python or other language base, but i would also like to heard about it)

  Read the article

• How to convince non-programmer his notions about computers are wrong?

  - by Suma

  Recently I came across a question about 64b on SuperUser for which the accepted answer seemed like a complete nonsense to me. I made two comments pointing out obvious mistakes. To my perplexion, the comments had an effect of the poster of the answer being alienated. I have no idea how could I convince him he is wrong, as he does not seem to understand the basics of the problem. He seems to be mixing concepts like bus size and address size - see the pearl sentence "it will allow you to address all of your RAM because your processor is reading from your RAM in 64 bit words.". The poster asks me to provide proves of my claim by quoting a respectable source, but I have no idea where to find such source, as I doubt anything I would consider relevant would be relevant for him (it would be probably too technical). I think this instance can serve as an illustration of communication problems between programmers and users (and to certain extent even to any expert vs. non-expert communication). How should a programmer handle a communication like this, so that is does not become a useless quarrel?

  Read the article

• Problems after installing a plethora of updates

  - by box

  yesterday I decided to install 32-bit Ubuntu on my 64-bit desktop, first of all, is that a problem? After installing, i had around 270 updates to install, according to the update manager. I was having trouble launching a game with WINE, so I thought updating might help. After updating, I restarted my computer, and after a long while it showed me my desktop and the icon's on it, but I didn't get anything else. I didn't have the "taskbar" (not sure what it's called, sue me) on the left side, nor the bar at the top. I also received an error message saying some program had stopped working. I decided to restart my computer again, and that was when it told me that i have to re-configure my drivers, or run in "Low Graphics" mode for one session, amongst other options. Well, I decided to try to revert to the "basic video drivers", which was an option it gave. Restarting the computer gave me the same problem as in the second paragraph. After a few more restarts and a night of restless sleep, here I am trying to start my computer again, only to receive a black screen, and my monitor "going to sleep". I'm sort of stumped here, being new to Ubuntu (desktop, at least) and I really hope this gets fixed without me having to install Ubuntu on yet another partition (I have three other partitions for various things already) tl;dr: Black screen on boot after installing updates.

  Read the article

• Wifi doesn't connect if I'm upstairs

  - by user11233

  Hello there, I'm finding that Wifi connects when I'm in the living room, where the internet router etc is. But if I try to connect upstairs it is a no go. Booting in Windows 7 (dual boot :D ) I find that Wifi connects. I find this very confusing and have it since the install. Please help! Kind regards. #sudo lshw -c network *-network description: Wireless interface product: PRO/Wireless 5100 AGN [Shiloh] Network Connection vendor: Intel Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 00 serial: 00:21:5d:1a:63:58 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlagn driverversion=2.6.35-26-generic firmware=8.24.2.12 ip=10.0.0.4 latency=0 link=yes multicast=yes wireless=IEEE 802.11abg resources: irq:49 memory:de200000-de201fff Hope it helps! Hello guys, just tried to connect internet upstairs and to my surprise it does connect. Don't know exactly why. Only thing I've done recently is input the codes said bij Oli. Two things I've done on my own 1: installed Jupiter and 2: installed laptop-mode-tools. I really don't know if this can effect my internet but it's the only thing I can think of. Thanks for all the help, really appreciate it :) PS If someone thinks it might be helpful for others I would like to help find a 'real' solution to this problem. Just post down what I need to post here and I will try my best to help.

  Read the article

• How do I get a Dell Latitude e6420 working?

  - by David_G

  I've just installed Ubuntu 12.04 (64-bit) on a brand new Dell Latitude e6420, and I'm having a few problems. This laptop has an Optimus (?) setup - i.e. integrated gfx and an Nvidia Quadro NVS 4200M. First problem - I ran setup, etc, and discovered that I can only run unity2d - If I try and login with unity3d, it just defaults to 2d. This is with nvidia-current installed (302.07). Note also that I can't run nvidia-settings ("You do not appear to be using the NVIDIA X driver."), and there is no additional drivers found ("No proprietary drivers are in use on this system"). I tried to troubleshoot this, and removed nvidia, leaving (I guess) just Nouveau drivers - In that case, unity3d did work, but I was stuck with the open source Nouveau drivers powering the integrated graphics. So, obviously, I want to run unity3d, and be using the more powerful Nvidia graphics card. I've tried a bit of tinkering around, but I'm not sure the best way to proceed, or perhaps more importantly, I'm not sure of what the best final solution might be. I've heard about bumblebee - but frankly, I would prefer to have the proprietary Nvidia drivers working properly. Any help would be much appreciated!

  Read the article

• Lost connectivity after configuring multiple network adapters on separate networks

  - by Dave Long

  I am trying to setup an Ubuntu hosting server, currently just for development, and the server has two NICs, each sitting on a different network. eth0 is on 192.168.200.* and eth1 is on 192.168.101.* and each one has a static IP. eth0 is the public facing NIC card and eth1 is strictly for internal access to the server. I initially only setup eth0 and added the eth1 card when I needed it. eth0 was working find until I added eth1, now, can't get any connectivity on eth0 unless I pull eth1 out of the box. The configuration on each system is as follows: auto eth0 iface eth0 inet static address 192.168.200.94 netmask 255.255.255.0 network 192.168.200.0 broadcast 192.168.200.255 gateway 192.168.200.253 auto eth1 iface eth1 inet static address 192.168.101.64 netmask 255.255.255.0 network 192.168.101.0 broadcast 192.168.101.255 gateway 192.168.101.254 Again eth0 worked fine until I added eth1. I have seen this happen with Windows servers if you have a Default Gateway setup for both NICs, but I am not sure if this works the same on Ubuntu. My resolv.conf file looks like so: nameserver 192.168.101.59 nameserver 192.168.101.58 domain domain.local search domain.local Per request here is the Routing table 192.168.101.0 * 255.255.255.0 U 0 0 0 eth1 192.168.200.0 * 255.255.255.0 U 0 0 0 eth0 default 192.168.101.254 0.0.0.0 UG 100 0 0 eth1 default 192.168.200.253 0.0.0.0 UG 100 0 0 eth0

  Read the article

• Can T520+Bumblebee run an external monitor via DisplayPort?

  - by Fen

  Using 64-bit Ubuntu 11.10 and integrated (Intel) graphics, I can run the 1600x900 laptop display plus a 1600x1200 external monitor connected to the VGA adapter. But my external monitor is 1920x1200 so I have black stripes on each side. I believe the resolution is limited like this as the maximum resolution available from the Intel GPU is 2560x1600 = 4,096,000 pixels and I'm asking for a 3520x1200 = 4,224,000 display (with 1200x300 lost above the laptop screen). At 3200x1200 = 3,840,000 pixels, the Intel GPU seems happy. Under Windows, the same limit exists when using the VGA adapter, but if I turn Optimus on then I can connect the external monitor to the DisplayPort and get its full resolution and an extended desktop. I've seen that Bumblebee can run apps on the DisplayPort using the 'optirun' command. My question is: can Bumblebee run the DisplayPort in concert with the Intel card running the laptop screen creating a large virtual desktop (as on Windows)? If so, are there any pointers to how to do this? I tried once, failed, and dropped back to Integrated Graphics (and black stripes) as I could find no reports of this configuration working.

  Read the article

• I have problem on 12.10 64bit with nvidia graphics driver opensource and proprietary ! Can't change resolution on 3d games

  - by digitalcrow

  I have problem with nvidia graphics driver opensource and proprietary ! Can't change resolution on 3d games and there's a bug there are no kernel sources installed and thus jockey can't install proprietary drivers. I can't change resolution while on games fullscreen. I tried to install proprietary driver and i couldn't plus i couldn't login to ubuntu it showed only the desktop photo no dash no nothing. -tried to install kernel sources and blacklist+remove Nouveau drivers and then installed the proprietary drivers i hope succesfully. -The problem is the same i can't change resolution on 3d games while on fullscreen. I've installed the sources and be able to install the proprietary nvidia drivers but the problem remains, look what i got in the output of a 3d game exited while i tried to change resolution: X Error of failed request: BadValue (integer parameter out of range for operation) Major opcode of failed request: 150 (XFree86-VidModeExtension) Minor opcode of failed request: 10 (XF86VidModeSwitchToMode) Value in failed request: 0x25b Serial number of failed request: 497 Current serial number in output stream: 499 I'm giving you more details about my system: i have an nvidia geforce gts 250 , 3,4 ghz quadcore amd phenom2 , 8gbytes of ram. The output of: sudo lshw -C display; lsb_release -a; uname -a Is the following: *-display description: VGA compatible controller product: G92 [GeForce GTS 250] vendor: NVIDIA Corporation physical id: 0 bus info: pci@0000:01:00.0 version: a2 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vga_controller bus_master cap_list rom configuration: driver=nvidia latency=0 resources: irq:18 memory:fa000000-faffffff memory:d0000000-dfffffff memory:f8000000-f9ffffff ioport:ef00(size=128) memory:fb000000-fb01ffff No LSB modules are available. Distributor ID: Ubuntu Description: Ubuntu 12.10 Release: 12.10 Codename: quantal Linux darkpc 3.5.0-17-generic #28-Ubuntu SMP Tue Oct 9 19:31:23 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux I like ubuntu's style and user interface but i hate the bad quality of work they do.

  Read the article

• Old Fglrx Driver - AMD Radeon HD 3200 - ubuntu won't start

  - by Yohannes

  I've been using Ubuntu 12.04 64 bit for about 2 weeks now and I installed the latest Fglrx driver (Graphics Card- AMD HD 3200, PC- Acer Aspire 5336, 4GB RAM, 500GB Harddrive). The problem is that sometimes video's lag and play out of sync sometimes the windows take long to show up after I've clicked them etc. After looking around I found a video on Youtube by Ubuntu help guy and in the video he recommended using an older driver if you have an older graphics card, his was about 4 years old (same as mine) and he used the 11.10 catalyst driver so I decided to try it. I removed the previous installation of the driver and then installed the 11.10 driver. However, when I restarted it instead of going to the GUI it goes to a terminal like window and asks for my login. Now its pretty clear I need to remove the old driver and go back to using the latest one. The only problem is I'm not sure where I saved the latest driver and in order to connect to the Internet I need to change /etc/resolv.conf (I use a static IP). So what should I do? Also anyone from personal experience, what propitiatory driver works best with my graphics card? As in the version. Thanks

  Read the article

• Random compositing lag

  - by user1020567

  My laptop specs: 512 mb of RAM, out of which 64 mb are shared with an integrated GPU - ATI Radeon Xpress 200 M. Intel 1,6 Ghz Celeron M single-core processor. I've spent months trying to figure out why compositing and effects sometimes lag on any distro I try. Now I've come to realise that no matter what drivers I try (the default ones work for me on pretty much any linux) compositing lag is random. When I used Ubuntu 10.10, for example, sometimes window compositing would lag and sometimes it wouldn't. The PC is able to render those effects so hardware is not the problem. It's completely random and unpredictable - sometimes when I turn on the computer the effects lag horribly and sometimes it's completely smooth. I've also checked startup items and there doesn't seem to be any unnecessary entries. I also tried building my own OS with Arch Linux and the problem persists there, therefore I can only assume that it's a driver issue of some sort. By default there are lots of drivers supplied with linux distributions. Could it be that they're in the way? The ones that I need are ati/radeon (or both? What's the difference between them?) and there seem to be a lot of others... What should I do?

  Read the article

• HP dv7 Beats Audio Subwoofer on while headphones plugged in

  - by msilis

  I have looked for answers to this but have not found anything. People have similar problems but mostly with getting the subwoofer to work at all. I got the subwoofer to work by editing the /etc/modprobe.d/alsa-base.conf file and adding options snd-hda-intel model=ref. When I plug in my headphones, the main speakers turn off but the subwoofer still has sound coming through it. The output is selected automatically in sound preferences and is set to headphones when they are plugged in. I also have tried muting the main speakers, which in turn mutes the subwoofer, before plugging in the headphones as they seem to have two different volume controls, but as soon as the headphones are plugged in, the subwoofer has sound coming out of it. I am running Ubuntu 11.10 64 bit on HP dv7- 4285dx. I am able to just not have the subwoofer on but since I have gotten it to work I would like to keep it around and not have to change a config file every time I want to plug in my headphones. Any ideas or suggestions would be greatly appreciated. Thanks

  Read the article

• Robust way to keep records of software releases?

  - by japreiss

  We release a number of small plug-ins that go along with our software. Each plug-in allows our software to talk to a single manufactuer's hardware. I would like to devise a system for keeping track of plug-in releases. Example info that should be stored: Hardware manufacturer name 32-bit? 64-bit? both? What modes of operation does the hardware support? What versions of the manufacturer's driver have been tested with the plugin? Desirable properties of the system: Able to synchronize with version control software Stores data in human-readable text file (also good for differ tool) Free visual, spreadsheet-like editor available Able to do simple analysis like "What is the oldest plug-in?" I've got to imagine that someone else has tackled this problem already. Right now my best guess is XML/JSON with a visual editor, but I have been disappointed in the editors I've tried so far. I'd like to get input from some more experienced developers. Thanks!

  Read the article

• Bootable dvd installs ubuntu in one computer but not in other...Why? [closed]

  - by SAM

  Possible Duplicate: My computer boots to a black screen, what options do I have to fix it? I have 2 computers, Windows 7 Intel. On one computer Ubuntu boot-able DVD (AMD 64) works properly. But on other computer the same DVD boots OK but when clicked on "Install Ubuntu" a blank screen with blinking cursor(_) appears and it continues just blinking forever. What problem can be there in computer 2? Can it be DVD reader's problem? (Both computers have LG DVD RW) Can there be any problem in DVD? Computer 1 specs: Pentium D 3 GHz Windows 7 32-bit not a 64bit-capable processor still Ubuntu 64bit trial/installer runs... Computer 2 specs: Core i7 2700k Windows 7 32-bit nvidia gtx 560 graphicsCard ...BIG BOSS... still can't run the setup/trial/disk-check/memory-test ?!?!? Is it the problem of graphics card ?!? I also tried burning other dvd which has the same behavour.... AND yes the dvd name is: ubuntu-12.04.1-dvd-amd64.iso Any help is appreciated.

  Read the article

• EOFs in Solaris 11

  - by nospam(at)example.com (Joerg Moellenkamp)

  Well ? from comments here and elsewhere, the two most worst things seemed to be the the removal of 32-bit support and removal of support for certain components. Just to set things into perspective: Solaris 10 was released 2005, the newsest class of machines not supported by it were the Ultra1. This one was released 1995. The UltraSPARC-Systems not able to run on Solaris 11 were released 2001. Well ? we have 2011 now ?. Regarding 32-bit support: Well ? I don't think "playing around with Solaris on old gear" is the problem. At first, most people are playing around with virtual machines. But there is something different: 64-bit computing was introduced for x86 in 2003 (yes ? it's really that old). I think this move is more hurting to the people using boards with the first-gen Intel Atom "Silverthorne" as small file servers. And then Solaris 10 won't disappear with Solaris 11

  Read the article

• Wireless is connected, but can't browse the Internet (or connection goes completely)

  - by user261007

  I'd like some help with this, please. Will be very glad is anyone will point me in the right direction. Thank you in advance! This is when the connection is present and browsing: eth0 Link encap:Ethernet HWaddr 50:46:5d:4a:9e:4f UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:2666 errors:0 dropped:0 overruns:0 frame:0 TX packets:2666 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:228844 (228.8 KB) TX bytes:228844 (228.8 KB) wlan0 Link encap:Ethernet HWaddr dc:85:de:1c:91:f9 inet addr:192.168.1.147 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::de85:deff:fe1c:91f9/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:18780 errors:0 dropped:0 overruns:0 frame:0 TX packets:12817 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:21198762 (21.1 MB) TX bytes:1746891 (1.7 MB) When connection goes: wlan0 Link encap:Ethernet HWaddr dc:85:de:1c:91:f9 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:209503 errors:0 dropped:0 overruns:0 frame:0 TX packets:132560 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:268811733 (268.8 MB) TX bytes:15479814 (15.4 MB)

  Read the article

< Previous Page | 234 235 236 237 238 239 240 241 242 243 244 245  | Next Page >