Search Results

Search found 10827 results on 434 pages for 'spring boot'.

Page 239/434 | < Previous Page | 235 236 237 238 239 240 241 242 243 244 245 246  | Next Page >

• How to reinstall OEM Windows 98 SE?

  - by Sammy

  I'm trying to install Windows 98 SE on an old PC and it's not going well. I run into this problem. Searching for Boot Record from Floppy..OK Starting Windows 98... TOSHIBA Enhanced-IDE CD/DVD-ROM Device Driver (ATAPI) Version 2.24 (C)Copyright Toshiba Corp. 1995-1999. All rights reserved. Device Name : TOSCD001 Number of units : 1 MSCDEX Version 2.25 Copyright (C) MIcrosoft Corp. 1986-1995. All rights reserved. Drive Z: = Driver TOSCD001 unit 0 TOSHIBA MACHINE Invalid drive specification Path not found - C:\TOOLS\CDROMDRV.SYS Invalid drive specification Invalid drive specification After that last line, it leaves me at a bitmap image displaying instructions to reboot with Ctrl+Alt+Del. It doesn't say why I have to reboot, and it doesn't state any error type, it just want's me to reboot for no apparent reason. After reboot, it just boots up from Floppy again and it cycles through the same thing all over again. The computer has been restored to original specification. Original system recovery "CD-ROM" discs are available and they are not scratched or anything, they are in very good condition. It's a set of 3 CDs, and the first disc labeled "1/3" should be the one holding the OEM version of Windows 98 SE. There is also a boot disk for Windows 98. I'm not sure what the other two discs are for. This computer came with three language support, so those could be holding different language versions or additional OEM discs. But I'm quite sure that the first disc holds the main operating system. BIOS has been set to optimized defaults. Boot priority is as follows; Floppy, IDE-0, CD-ROM. Under Standard CMOS settings, BIOS scans and autoconfigures both the hard drive and the CD/DVD drive. On POST it finds them both, and it finds the DOS bootdisk and starts preparing for installation, as you can see above. So what's this "invalid drive specification" about? Why isn't the installation starting? Updates Update 1 Booting from CD disc 2 In desperation I tried booting from the second CD. Boot order was; Floppy, CD-ROM, IDE-0. It boots normally from floppy disk, just like above, but then returns following. File not found - Z:\3LNGINST\TOOLS\PARTINFO.TXT I accidentally pressed some key on the keyboard, and before I knew it, the following screen showed up. Create Primary DOS Partition Current fixed disk drive: 1 Verifying drive integrity, 16% complete. After completion another screen showed up. Create Primary DOS Partition Current fixed disk drive: 1 Do you wish to use the maximum available size for a Primary DOS Partition and make the partition active (Y/N)?....................? [Y] Verifying drive integrity, 7% complete. I didn't choose Yes, it was set automatically. After completion the computer was automatically rebooted. Then I got a new screen. This is in Norwegian/Swedish/Finnish. Here's the message in Swedish. Hårddisken är inte klar för återställning av programvara. Installationsprogrammet måste skapa nya partitioner (C:, D:, ...). VARNING! ALLT INNEHÅLL PÅ HÅRDDISKEN KOMMER ATT RADERAS! Tryck på en tangent om du vill fortsätta (eller CTRL-C för att avbryta). Let me translate that. Hard drive is not ready for restoring the software. Setup program has to create new partitions (C:, D:, ...). WARNING! ALL CONTENTS ON THE HARD DRIVE WILL BE ERASED! Press any key to continue (or CTRL-C to cancel). I pressed Enter and it started formatting the hard drive. WARNING, ALL DATA ON NON-REMOVABLE DISK DRIVE c: WILL BE LOST! Proceed with Format (Y/N)?y Formatting 14,67.53M 1 percent completed. It automatically sets the "y" option and starts formatting. Rebooting with CD disc 1 After completing this operation it rebooted automatically. I inserted CD disc 1 and there was no issue with "invalid drive specification" anymore. Instead, a bitmap menu was displayed where it asked me to choose a language. And I thought I had it there for a while but it didn't work out. After choosing the language, another menu was displayed asking me to choose a type of recovery (restore pre-installed software OR restore hard drive partitions and pre-installed software). I opted for the second option. Then a data destruction warning showed up where I just pressed 1 to Continue. It did something and then just rebooted and the same formatting screen shows up as before. So something is not right. Am I doing it wrong? I seem to have come past the CD-ROM driver issue at least. But now I'm stuck with this problem... it seems to have something to do with the hard drive. Like... why is is it always trying to format it? Isn't it enough to format it once? By the way, it needs to be formatted as FAT32, right? Windows 98 doesn't support NTFS? I think FDISK should have taken care of this already. I know this is an old hard drive, but I connected to my main computer and it was able to read and write to it without a problem. It does have bad sectors though, but it's expected on an old hard drive like this. Any ideas?.. Update 2 I seem to be repeatedly getting stuck at the format screen where it asks to press any key to continue. So tried to cancel it this time with Ctrl+C. This leaves me at: A:\TOOLS> I can do DIR and CD and I tried to change to Z: drive. I tried running "setup" but there is no such thing. Z:\>setup Bad command or file name Update 3 Floppy structure Here's the file/folder structure of the floppy disk. A:\>dir /s Volume in drive A has no label. Volume Serial Number is 1700-1069 Directory of A:\ 1999-10-11 10:44 <DIR> BMP 1998-05-11 22:01 93 880 COMMAND.COM 1999-10-11 10:44 <DIR> factory 1999-10-11 10:44 <DIR> lang 1999-10-11 10:44 <DIR> TOOLS 2000-05-19 15:32 339 CONFIG.SYS 1999-10-26 13:38 0 BOOTLOG.TXT 2000-06-08 08:32 3 691 AUTOEXEC.BAT 4 File(s) 97 910 bytes Directory of A:\BMP 1999-10-11 10:44 <DIR> . 1999-10-11 10:44 <DIR> .. 0 File(s) 0 bytes Directory of A:\factory 1999-10-11 10:44 <DIR> . 1999-10-11 10:44 <DIR> .. 2000-06-08 13:09 2 662 3LNGINSF.BAT 1 File(s) 2 662 bytes Directory of A:\lang 1999-10-11 10:44 <DIR> . 1999-10-11 10:44 <DIR> .. 1998-11-24 08:02 49 575 FORMAT.COM 1998-11-24 08:02 63 900 FDISK.EXE 2 File(s) 113 475 bytes Directory of A:\TOOLS 1999-10-11 10:44 <DIR> . 1999-10-11 10:44 <DIR> .. 1998-05-06 22:01 49 575 FORMAT.COM 1995-10-27 20:29 28 164 BMPVIEW.EXE 1999-01-26 15:54 15 MAKEPA32.TXT 1998-05-06 22:01 3 878 XCOPY.EXE 1998-05-06 22:01 41 472 XCOPY32.MOD 1998-05-06 22:01 33 191 HIMEM.SYS 1998-05-06 22:01 125 495 EMM386.EXE 1998-05-06 22:01 18 967 SYS.COM 1996-01-31 21:55 18 CLK.COM 1994-04-02 08:20 22 HARDBOOT.COM 1999-02-03 15:46 15 MAKEPA16.TXT 1999-04-14 16:36 7 840 PARTFO32.EXE 2000-05-19 15:01 1 169 PARTFORM.BAT 1996-10-02 01:47 1 642 MBRCLR.COM 1999-07-01 11:58 8 175 BIOSCHKN.EXE 1998-06-23 08:55 5 904 PAR-TYPE.EXE 1998-11-24 08:02 29 271 MODE.COM 1998-11-24 08:02 15 252 ATTRIB.EXE 1998-11-24 08:02 19 083 DELTREE.EXE 1999-04-21 15:01 23 304 NTBB.EXE 1997-05-07 14:19 1 SYS.TXT 1999-07-01 12:23 61 566 F3DCHK.EXE 1998-05-11 20:01 34 566 KEYBOARD.SYS 1998-05-11 20:01 19 927 KEYB.COM 1999-10-26 14:31 910 partinfo.txt 1998-06-16 15:58 5 936 CHKDRVAC.EXE 1998-05-06 22:01 63 900 FDISK.EXE 1998-05-06 22:01 45 379 SMARTDRV.EXE 1992-12-03 19:48 10 695 SCISET.EXE 1997-06-25 15:49 6 YENT 1998-05-06 22:01 25 473 MSCDEX.EXE 1998-05-06 22:01 5 239 CHOICE.COM 1997-07-18 17:41 6 876 MBR.COM 1997-07-01 15:01 6 545 CHK2GB.COM 1998-06-10 20:04 8 128 PARTFORM.EXE 1990-01-04 02:09 19 MAKEPAR2.TXT 1990-01-04 01:00 27 MAKEPAR3.TXT 1990-01-04 01:00 27 MAKEPAR4.TXT 1998-02-13 13:47 15 MAKEPART.TXT 1999-04-14 13:47 5 200 DISKSIZE.EXE 1999-05-06 14:56 7 856 PARTFO16.EXE 1999-01-13 11:13 13 720 CDROMDRV.SYS 42 File(s) 734 463 bytes Total Files Listed: 49 File(s) 948 510 bytes 12 Dir(s) 268 800 bytes free A:\> CONFIG.SYS contents Here's the content of CONFIG.SYS. DEVICE=A:\TOOLS\HIMEM.SYS /TESTMEM:OFF REM I=B000-B7ff for Desktop BIOSes rem DEVICE=A:\TOOLS\EMM386.EXE NOEMS I=B000-B7ff x=C000-D000 DEVICE=A:\TOOLS\EMM386.EXE NOEMS x=C000-D000 DEVICE=A:\TOOLS\CDROMDRV.SYS /D:TOSCD001 BUFFERS=10 FILES=69 DOS=HIGH,UMB STACKS=9,256 LASTDRIVE=Z SWITCHES=/F SHELL=A:\COMMAND.COM /P /E:2048 AUTOEXEC.BAT contents :BEGIN @ECHO OFF PATH=A:\;A:\TOOLS; MSCDEX /D:TOSCD001 /L:Z /M:10 smartdrv 1024 128 SET TOOLS=A:\TOOLS SET COMSPEC=A:\COMMAND.COM SET EXITDRIVE=C: SET EXITPATH=\ CALL Z:\SETENV.BAT > NUL :TOSHCHK BIOSChkN IF NOT ERRORLEVEL 1 goto C_ACCESS BMPVIEW Z:\3LNGINST\BMP\NO_TOSP3.bmp /X=120 /Y=80 PAUSE > NUL SET EXITDRIVE=A: GOTO END :C_ACCESS CALL PARTFORM.BAT :C_EMPTY IF EXIST C:\*.* GOTO C_NOTEMPTY call z:\setenv.bat>nul goto PREPDU :C_NOTEMPTY REM ------------------MENU------------------------ :STARTMENU CLS BMPVIEW Z:\3LNGINST\BMP\LANGSELC.BMP /X=120 /Y=120 CLK CHOICE /C:123 /N >NUL REM L is the language that is selected IF ERRORLEVEL 1 SET L=%LNG1% IF ERRORLEVEL 2 SET L=%LNG2% IF ERRORLEVEL 3 SET L=%LNG3% SET BMP=BMP%L% BMPVIEW Z:\3LNGINST\%bmp%\HDDMENU.BMP /X=72 /Y=82 CLK CHOICE /C:129F /N > NUL IF ERRORLEVEL 4 GOTO FACTORY_MENU IF ERRORLEVEL 3 GOTO EXIT_MENU IF ERRORLEVEL 2 GOTO PARTFORM_MENU IF ERRORLEVEL 1 GOTO FORMAT_MENU GOTO END :FACTORY_MENU BMPVIEW Z:\3LNGINST\%bmp%\qformat.bmp /X=120 /Y=140 CLK choice /c:12 /N >nul IF ERRORLEVEL 2 GOTO STARTMENU IF ERRORLEVEL 1 GOTO FORMATF GOTO END :EXIT_MENU BMPVIEW Z:\3LNGINST\%bmp%\9.bmp /XC /X=96 /Y=267 choice /C:1pause /T:1,01 >nul SET EXITDRIVE=A: SET EXITPATH=\lang cls mode mono rem keyb xx>nul cls GOTO END :PARTFORM_MENU BMPVIEW Z:\3LNGINST\%bmp%\2.bmp /XC /X=96 /Y=216 choice /C:1pause /T:1,01 >nul BMPVIEW Z:\3LNGINST\%bmp%\partform.bmp /X=120 /Y=140 CLK choice /c:12 /N >nul IF ERRORLEVEL 2 GOTO STARTMENU IF ERRORLEVEL 1 GOTO PART_FORM SET EXITDRIVE=A: GOTO END :FORMAT_MENU BMPVIEW Z:\3LNGINST\%bmp%\1.bmp /XC /X=96 /Y=165 choice /C:1pause /T:1,01 >nul BMPVIEW Z:\3LNGINST\%bmp%\qformat.bmp /X=120 /Y=140 CLK choice /c:12 /N >nul IF ERRORLEVEL 2 GOTO STARTMENU IF ERRORLEVEL 1 GOTO FORMAT SET EXITDRIVE=A: GOTO END REM ------------------ MENU END ------------------------ :FORMAT bmpview Z:\3LNGINST\%bmp%\1.bmp /XC /X=145 /Y=235 choice /C:1pause /T:1,01 >nul CLS IF (%QFORMAT%)==(NO) GOTO FULLFO FORMAT C: /Q /V:"" <A:\TOOLS\YENT >NUL call z:\setenv.bat>nul goto PREPDU :FULLFO FORMAT C: /V:"" <A:\TOOLS\YENT call z:\setenv.bat>nul goto PREPDU :FORMATF CLS IF (%QFORMAT%)==(NO) GOTO FULLFO_F FORMAT C: /Q /V:"" <A:\TOOLS\YENT >NUL call z:\setenv.bat>nul goto PREPDU_F :FULLFO_F FORMAT C: /V:"" <A:\TOOLS\YENT call z:\setenv.bat>nul goto PREPDU_F :PART_FORM bmpview Z:\3LNGINST\bmp\1.bmp /XC /X=145 /Y=235 choice /C:1pause /T:1,01 >nul MBR /! HARDBOOT REM ====================== Triple Select ====================== :PREPDU XCOPY z:\3LNGINST\*.* C:\*.* /E /S /V >NUL ATTRIB -H -R -S C:\TOOLS\CDROMDRV.SYS COPY A:\TOOLS\CDROMDRV.SYS C:\TOOLS /Y SYS C: >NUL goto REBOOT :PREPDU_F copy A:\TOOLS\SMARTDRV.EXE C:\ /Y ATTRIB -H -R -S C:\SMARTDRV.EXE copy A:\FACTORY\3LNGINSF.bat c:\ c:\3LNGINSF.bat cls REM ====================== Dual Select END ====================== REM --------------- END ------------------ :REBOOT SMARTDRV.EXE /C bmpview Z:\3LNGINST\BMP\reboot3.bmp /X=120 /Y=140 :FOREVER pause >nul goto FOREVER :END SMARTDRV.EXE /C %EXITDRIVE% cd %EXITPATH% echo on CD structure S:\>dir /s Volume in drive S is T3ELK4SC Volume Serial Number is 2042-5BC9 Directory of S:\ 2000-08-22 14:14 <DIR> 3LNGINSF 2000-08-22 14:14 <DIR> 3LNGINST 2000-06-15 15:57 <DIR> CRC 2000-06-15 12:04 387 667 767 T310C1NO.W98 2000-09-07 15:36 273 setenv.BAT 2 File(s) 387 668 040 bytes Directory of S:\3LNGINSF 1601-01-01 02:00 <DIR> . 1601-01-01 02:00 <DIR> .. 1999-10-27 10:51 1 806 AUTOEXEC.BAT 2000-08-22 14:14 <DIR> BMP 2000-05-19 15:29 265 CONFIG.SYS 2000-08-22 14:14 <DIR> POSTINST 2000-08-22 14:14 <DIR> TOOLS 2000-08-22 14:14 <DIR> WIN98SYS 2 File(s) 2 071 bytes Directory of S:\3LNGINSF\BMP 1601-01-01 02:00 <DIR> . 1601-01-01 02:00 <DIR> .. 1997-04-22 09:43 718 1.BMP 1997-04-22 09:44 718 2.BMP 1999-01-04 02:38 718 3.BMP 2000-07-05 11:22 60 118 Cdchg2.bmp 2000-07-05 11:22 60 118 Cdchg3.bmp 2000-07-05 13:37 60 118 Fin.bmp 2000-07-06 14:18 120 118 Menu.bmp 2000-07-05 13:34 60 118 Nor.bmp 2000-07-05 11:53 35 318 Progress.bmp 2000-07-05 13:40 60 118 Swe.bmp 2000-07-05 12:09 84 118 Wrongcd2.bmp 2000-07-05 12:09 84 118 Wrongcd3.bmp 12 File(s) 626 416 bytes Directory of S:\3LNGINSF\POSTINST 1601-01-01 02:00 <DIR> . 1601-01-01 02:00 <DIR> .. 2000-05-19 09:15 33 POSTINST.BAT 1 File(s) 33 bytes Directory of S:\3LNGINSF\TOOLS 1601-01-01 02:00 <DIR> . 1601-01-01 02:00 <DIR> .. 2000-07-06 14:49 3 593 3LNGINST.BAT 1998-11-24 08:02 15 252 ATTRIB.EXE 1995-10-27 18:29 28 164 BMPVIEW.EXE 1999-01-13 11:13 13 720 CDROMDRV.SYS 1998-05-06 20:01 5 239 CHOICE.COM 1996-01-31 19:55 18 CLK.COM 1998-11-24 08:02 19 083 DELTREE.EXE 1998-05-06 20:01 125 495 EMM386.EXE 1999-07-01 12:23 61 566 F3DCHK.EXE 1998-05-06 20:01 49 575 FORMAT.COM 1994-04-02 06:20 22 HARDBOOT.COM 1998-05-06 20:01 33 191 HIMEM.SYS 1998-05-06 20:01 25 473 MSCDEX.EXE 1998-05-06 20:01 12 663 RAMDRIVE.SYS 1998-05-06 20:01 45 379 SMARTDRV.EXE 1997-05-07 14:19 1 SYS.TXT 1995-09-27 14:25 6 813 VOLCHECK.EXE 1998-05-06 20:01 3 878 XCOPY.EXE 1998-05-06 20:01 41 472 XCOPY32.MOD 1997-06-25 13:49 6 YENT 20 File(s) 490 603 bytes Directory of S:\3LNGINSF\WIN98SYS 1601-01-01 02:00 <DIR> . 1601-01-01 02:00 <DIR> .. 1998-12-04 20:00 222 390 IO.SYS 1998-05-06 20:01 18 967 SYS.COM 1998-05-06 20:01 93 880 command.com 3 File(s) 335 237 bytes Directory of S:\3LNGINST 1601-01-01 02:00 <DIR> . 1601-01-01 02:00 <DIR> .. 1999-05-31 09:51 1 576 AUTOEXEC.BAT 2000-08-22 14:14 <DIR> BMP 2000-08-22 14:14 <DIR> Bmpfin 2000-08-22 14:14 <DIR> Bmpnor 2000-08-22 14:14 <DIR> Bmpswe 2000-05-19 15:30 265 CONFIG.SYS 2000-08-22 14:14 <DIR> POSTINST 2000-08-22 14:14 <DIR> TOOLS 2000-08-22 14:14 <DIR> WIN98SYS 2 File(s) 1 841 bytes Directory of S:\3LNGINST\BMP 1601-01-01 02:00 <DIR> . 1601-01-01 02:00 <DIR> .. 1997-04-22 09:43 718 1.BMP 1997-04-22 09:44 718 2.BMP 1999-01-04 02:38 718 3.BMP 2000-07-05 11:22 60 118 Cdchg2.bmp 2000-07-05 11:22 60 118 Cdchg3.bmp 2000-07-05 13:37 60 118 Fin.bmp 2000-07-06 14:18 120 118 Menu.bmp 2000-07-05 13:34 60 118 Nor.bmp 2000-07-05 11:53 35 318 Progress.bmp 2000-07-06 14:08 40 518 Reboot3.bmp 2000-07-05 13:40 60 118 Swe.bmp 2000-07-05 12:09 84 118 Wrongcd2.bmp 2000-07-05 12:09 84 118 Wrongcd3.bmp 2000-07-05 13:52 48 118 langselc.bmp 2000-07-05 11:47 57 318 no_tosp3.bmp 15 File(s) 772 370 bytes Directory of S:\3LNGINST\Bmpfin 1601-01-01 02:00 <DIR> . 1601-01-01 02:00 <DIR> .. 1997-04-22 09:43 718 1.BMP 1997-04-22 09:44 718 2.BMP 1998-06-13 00:07 718 9.bmp 2000-03-08 15:02 78 486 Hddmenu.bmp 2000-03-08 15:31 25 318 No_tospc.bmp 2000-03-08 15:37 36 518 PARTFORM.BMP 2000-03-08 15:42 36 518 Qformat.bmp 7 File(s) 178 994 bytes Directory of S:\3LNGINST\Bmpnor 1601-01-01 02:00 <DIR> . 1601-01-01 02:00 <DIR> .. 1997-04-22 09:43 718 1.BMP 1997-04-22 09:44 718 2.BMP 1998-06-13 00:07 718 9.bmp 1999-05-05 13:26 78 486 Hddmenu.bmp 1998-07-13 11:36 25 318 No_tospc.bmp 1998-07-13 11:41 36 518 PARTFORM.BMP 1998-07-13 11:45 36 518 Qformat.bmp 7 File(s) 178 994 bytes Directory of S:\3LNGINST\Bmpswe 1601-01-01 02:00 <DIR> . 1601-01-01 02:00 <DIR> .. 1997-04-22 09:43 718 1.BMP 1997-04-22 09:44 718 2.BMP 1998-06-13 00:07 718 9.bmp 1999-05-06 08:14 78 486 Hddmenu.bmp 1998-07-10 16:25 25 318 No_tospc.bmp 1998-07-10 16:29 36 518 PARTFORM.BMP 1998-07-10 17:08 36 518 Qformat.bmp 7 File(s) 178 994 bytes Directory of S:\3LNGINST\POSTINST 1601-01-01 02:00 <DIR> . 1601-01-01 02:00 <DIR> .. 2000-05-19 09:15 33 POSTINST.BAT 1 File(s) 33 bytes Directory of S:\3LNGINST\TOOLS 1601-01-01 02:00 <DIR> . 1601-01-01 02:00 <DIR> .. 2000-05-19 14:52 3 898 3LNGINST.BAT 1995-10-27 18:29 28 164 BMPVIEW.EXE 1999-01-13 11:13 13 720 CDROMDRV.SYS 1998-05-06 20:01 5 239 CHOICE.COM 1996-01-31 19:55 18 CLK.COM 1998-05-06 20:01 125 495 EMM386.EXE 1999-07-01 12:23 61 566 F3DCHK.EXE 1998-05-06 20:01 49 575 FORMAT.COM 1994-04-02 06:20 22 HARDBOOT.COM 1998-05-06 20:01 33 191 HIMEM.SYS 1998-05-06 20:01 25 473 MSCDEX.EXE 2000-07-06 14:41 910 PARTINFO.TXT 1998-05-06 20:01 12 663 RAMDRIVE.SYS 1998-05-06 20:01 45 379 SMARTDRV.EXE 1997-05-07 14:19 1 SYS.TXT 1995-09-27 14:25 6 813 VOLCHECK.EXE 1998-05-06 20:01 3 878 XCOPY.EXE 1998-05-06 20:01 41 472 XCOPY32.MOD 1997-06-25 13:49 6 YENT 19 File(s) 457 483 bytes Directory of S:\3LNGINST\WIN98SYS 1601-01-01 02:00 <DIR> . 1601-01-01 02:00 <DIR> .. 1998-12-04 20:00 222 390 IO.SYS 1998-05-06 20:01 18 967 SYS.COM 1998-05-06 20:01 93 880 command.com 3 File(s) 335 237 bytes Directory of S:\CRC 1601-01-01 02:00 <DIR> . 1601-01-01 02:00 <DIR> .. 2000-06-15 12:07 181 422 T310C1NO.ALL 2000-06-15 12:09 215 427 T310C1NO.CRC 2000-06-15 12:07 2 157 T310C1NO.HID 3 File(s) 399 006 bytes Total Files Listed: 104 File(s) 391 625 352 bytes 42 Dir(s) 0 bytes free S:\> Now which line or lines need to be changed? Do I really have to change drive letter Z: to C:? Proposed solutions Solution #1 Ramhound proposed to change the boot order to following; CD-ROM, IDE-0, Floppy This didn't help. In fact, here is the result of it. Searching for Boot Record from CDROM..Not Found Searching for Boot Record from IDE-0.. OK Missing operating system Any other ideas?... Solution #2 Rik proposed to run Z:\setup. Now that I have found a way to drop to DOS prompt with Ctrl+C as described above (Update 2), I did try running setup but there is no such command or file in there. So that didn't work.

  Read the article

• Learning Python and trying to get first two letters and last two letters of a string.

  - by Sergio Tapia

  Here's my code: # B. both_ends # Given a string s, return a string made of the first 2 # and the last 2 chars of the original string, # so 'spring' yields 'spng'. However, if the string length # is less than 2, return instead the empty string. def both_ends(s): if len(s) <= 2: return "" else: return s[0] + s[1] + s[len(s)-2] + s[len(s-1)] # +++your code here+++ return Unfortunately my program doesn't run. :( I'm sure I'm overlooking something since I'm a newbie with Python. Here's the error: > Traceback (most recent call last): File "C:\Users\Sergio\Desktop\google-python-exercises\google-python-exercises\basic\string1.py", line 120, in <module> main() File "C:\Users\Sergio\Desktop\google-python-exercises\google-python-exercises\basic\string1.py", line 97, in main test(both_ends('spring'), 'spng') File "C:\Users\Sergio\Desktop\google-python-exercises\google-python-exercises\basic\string1.py", line 44, in both_ends return s[0] + s[1] + s[len(s)-2] + s[len(s-1)] TypeError: unsupported operand type(s) for -: 'str' and 'int' Thanks for the help guys. :D

  Read the article

• How to configure MessageEndpointMapping by namespace in NServiceBus

  - by SteveBering

  I am trying to configure my message endpoint mapping in my NServiceBus configuration by sending messages from different namespaces to different endpoints. As such, I have configured the following in my web.config: However, when my application starts, I receive the following exception: Spring.Objects.PropertyAccessExceptionsException: PropertyAccessExceptionsException (1 errors); nested PropertyAccessExceptions are: [Spring.Core.TypeMismatchException: Cannot convert property value of type [System.Collections.Hashtable] to required type [System.Collections.IDictionary] for property 'MessageOwners'., Inner Exception: System.ArgumentException: Problem loading message assembly: Company.Messages.Payments --- System.IO.FileNotFoundException: Could not load file or assembly 'Company.Messages.Payments' or one of its dependencies. The system cannot find the file specified. File name: 'Company.Messages.Payments' What I find interesting is that it seems to have found Company.Messages.Accounts but failed on the second configured line. I thought that maybe it didn't like have them all go to the same endpoint, but changing this configuration to have them go different endpoints didn't change the error message I received. What am I doing wrong? Is it not possible to segment messages by namespace (all I have seen is by type and by assembly)? Thanks, Steve

  Read the article

• GWT and java.io.Serializable

  - by Ethan Leroy

  Hello, In my GWT app I have the following model class: import com.google.gwt.user.client.rpc.IsSerializable; public class TestEntity implements IsSerializable { public String testString; } This class implements the GWT custom IsSerializable marker interface - which I really don't like, because I use my model classes not only for GWT. So I prefer java.io.Serializable. But if I modify the class to implement Serializable instead of IsSerializable, the GWT RPC mechanism doesn't work anymore. I don't get an error on the server side, but on the client AsyncCallback.onFailure is invoked. I am using... GWT 1.7.0. Spring 2.5.6.SEC01 Spring and GWT are configured as described here.

  Read the article

• Managed server not starting up however Admin console is up.

  - by Preet

  Hi, Scenario: If i try to start the server as a window service it gives an error stating that ceradentials are not correct.However on correcting the credentials in boot.properties when i try to start the server again it gives the same error.Any alternative for starting the server.I gave the same username and password in my startup Script and Boot.properties. Scenario 2: If i start the server remotely through console then will it come up? Thanks in advance. Regards, Preet

  Read the article

• SQL Anywhere 11, JZ0C0: Connection is already closed

  - by Alex

  SLOVED see commend I develop am webservice based on apache tomcat 6.0.26, apache cxf 2.2.7, spring 3.0, hibernate 3.3 and sybase sqlanywhere 11. im using the latest JDBC Driver from SYBASE jconn.jar Version 6. The persistence layer is based on spring + hibernate dao, the connection is configured via a JNDI datasoure (META-INF directory). It seems that, during longer times of inactivity, the connection from the webservice to the database is closed. Exception: java.sql.SQLException: JZ0C0: Connection is already closed. Best regards, Alex

  Read the article

• Error : java.lang.NoSuchMethodError: org.objectweb.asm.ClassWriter.<init>(I)V

  - by Hitesh Solanki

  Hiii.... I am developing small spring application. I have to store the details of the student information in the database. I have develop one simpleformcontroller.I have used netbeans + hibernate mapping + spring. when I deploy the project,the following errors is occured. please help me.. Thanks in advance..... My spring-config-db-applicationContext.xml is shown below: <?xml version="1.0" encoding="UTF-8"?> ${driverClassName} ${url} ${username} ${password} WEB-INF/classes/hibernate.cfg.xml -- hibernate.cfg.xml org.hibernate.cfg.AnnotationConfiguration -- <property name="hibernateProperties"> <props> <prop key="hibernate.dialect">${dialect}</prop> <prop key="hibernate.show_sql">true</prop> <!--<prop key="hibernate.hbm2ddl.auto">create</prop>--> </props> </property> </bean> Following error is occured: ERROR (org.springframework.web.context.ContextLoader:213) - Context initialization failed org.springframework.beans.factory.BeanCreationException: Error creating bean with name 'sessionFactory' defined in URL [jndi:/localhost/Student/WEB-INF/classes/config/spring-db-applicationContext.xml]: Invocation of init method failed; nested exception is java.lang.NoSuchMethodError: org.objectweb.asm.ClassWriter.(I)V at org.springframework.beans.factory.support.AbstractAutowireCapableBeanFactory.initializeBean(AbstractAutowireCapableBeanFactory.java:1395) at org.springframework.beans.factory.support.AbstractAutowireCapableBeanFactory.doCreateBean(AbstractAutowireCapableBeanFactory.java:512) at org.springframework.beans.factory.support.AbstractAutowireCapableBeanFactory.createBean(AbstractAutowireCapableBeanFactory.java:450) at org.springframework.beans.factory.support.AbstractBeanFactory$1.getObject(AbstractBeanFactory.java:289) at org.springframework.beans.factory.support.DefaultSingletonBeanRegistry.getSingleton(DefaultSingletonBeanRegistry.java:222) at org.springframework.beans.factory.support.AbstractBeanFactory.doGetBean(AbstractBeanFactory.java:286) at org.springframework.beans.factory.support.AbstractBeanFactory.getBean(AbstractBeanFactory.java:188) at org.springframework.beans.factory.support.DefaultListableBeanFactory.preInstantiateSingletons(DefaultListableBeanFactory.java:526) at org.springframework.context.support.AbstractApplicationContext.finishBeanFactoryInitialization(AbstractApplicationContext.java:730) at org.springframework.context.support.AbstractApplicationContext.refresh(AbstractApplicationContext.java:387) at org.springframework.web.context.ContextLoader.createWebApplicationContext(ContextLoader.java:270) at org.springframework.web.context.ContextLoader.initWebApplicationContext(ContextLoader.java:197) at org.springframework.web.context.ContextLoaderListener.contextInitialized(ContextLoaderListener.java:47) at org.apache.catalina.core.StandardContext.listenerStart(StandardContext.java:3843) at org.apache.catalina.core.StandardContext.start(StandardContext.java:4342) at org.apache.catalina.core.ContainerBase.addChildInternal(ContainerBase.java:791) at org.apache.catalina.core.ContainerBase.addChild(ContainerBase.java:771) at org.apache.catalina.core.StandardHost.addChild(StandardHost.java:525) at org.apache.catalina.startup.HostConfig.deployDescriptor(HostConfig.java:627) at org.apache.catalina.startup.HostConfig.deployApps(HostConfig.java:511) at org.apache.catalina.startup.HostConfig.check(HostConfig.java:1231) at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method) at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39) at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25) at java.lang.reflect.Method.invoke(Method.java:597) at org.apache.tomcat.util.modeler.BaseModelMBean.invoke(BaseModelMBean.java:297) at com.sun.jmx.interceptor.DefaultMBeanServerInterceptor.invoke(DefaultMBeanServerInterceptor.java:836) at com.sun.jmx.mbeanserver.JmxMBeanServer.invoke(JmxMBeanServer.java:761) at org.apache.catalina.manager.ManagerServlet.check(ManagerServlet.java:1471) at org.apache.catalina.manager.ManagerServlet.deploy(ManagerServlet.java:824) at org.apache.catalina.manager.ManagerServlet.doGet(ManagerServlet.java:350) at javax.servlet.http.HttpServlet.service(HttpServlet.java:617) at javax.servlet.http.HttpServlet.service(HttpServlet.java:717) at org.apache.catalina.core.ApplicationFilterChain.internalDoFilter(ApplicationFilterChain.java:290) at org.apache.catalina.core.ApplicationFilterChain.doFilter(ApplicationFilterChain.java:206) at org.netbeans.modules.web.monitor.server.MonitorFilter.doFilter(MonitorFilter.java:196) at org.apache.catalina.core.ApplicationFilterChain.internalDoFilter(ApplicationFilterChain.java:235) at org.apache.catalina.core.ApplicationFilterChain.doFilter(ApplicationFilterChain.java:206) at org.apache.catalina.core.StandardWrapperValve.invoke(StandardWrapperValve.java:233) at org.apache.catalina.core.StandardContextValve.invoke(StandardContextValve.java:191) at org.apache.catalina.authenticator.AuthenticatorBase.invoke(AuthenticatorBase.java:525) at org.apache.catalina.core.StandardHostValve.invoke(StandardHostValve.java:128) at org.apache.catalina.valves.ErrorReportValve.invoke(ErrorReportValve.java:102) at org.apache.catalina.core.StandardEngineValve.invoke(StandardEngineValve.java:109) at org.apache.catalina.connector.CoyoteAdapter.service(CoyoteAdapter.java:286) at org.apache.coyote.http11.Http11Processor.process(Http11Processor.java:845) at org.apache.coyote.http11.Http11Protocol$Http11ConnectionHandler.process(Http11Protocol.java:583) at org.apache.tomcat.util.net.JIoEndpoint$Worker.run(JIoEndpoint.java:447) at java.lang.Thread.run(Thread.java:619) Caused by: java.lang.NoSuchMethodError: org.objectweb.asm.ClassWriter.(I)V at net.sf.cglib.core.DebuggingClassWriter.(DebuggingClassWriter.java:47) at net.sf.cglib.core.DefaultGeneratorStrategy.getClassWriter(DefaultGeneratorStrategy.java:30) at net.sf.cglib.core.DefaultGeneratorStrategy.generate(DefaultGeneratorStrategy.java:24) at net.sf.cglib.core.AbstractClassGenerator.create(AbstractClassGenerator.java:216) at net.sf.cglib.core.KeyFactory$Generator.create(KeyFactory.java:144) at net.sf.cglib.core.KeyFactory.create(KeyFactory.java:116) at net.sf.cglib.core.KeyFactory.create(KeyFactory.java:108) at net.sf.cglib.core.KeyFactory.create(KeyFactory.java:104) at net.sf.cglib.proxy.Enhancer.(Enhancer.java:69) at org.hibernate.proxy.pojo.cglib.CGLIBLazyInitializer.getProxyFactory(CGLIBLazyInitializer.java:117) at org.hibernate.proxy.pojo.cglib.CGLIBProxyFactory.postInstantiate(CGLIBProxyFactory.java:43) at org.hibernate.tuple.entity.PojoEntityTuplizer.buildProxyFactory(PojoEntityTuplizer.java:162) at org.hibernate.tuple.entity.AbstractEntityTuplizer.(AbstractEntityTuplizer.java:135) at org.hibernate.tuple.entity.PojoEntityTuplizer.(PojoEntityTuplizer.java:55) at org.hibernate.tuple.entity.EntityEntityModeToTuplizerMapping.(EntityEntityModeToTuplizerMapping.java:56) at org.hibernate.tuple.entity.EntityMetamodel.(EntityMetamodel.java:302) at org.hibernate.persister.entity.AbstractEntityPersister.(AbstractEntityPersister.java:434) at org.hibernate.persister.entity.SingleTableEntityPersister.(SingleTableEntityPersister.java:108) at org.hibernate.persister.PersisterFactory.createClassPersister(PersisterFactory.java:61) at org.hibernate.impl.SessionFactoryImpl.(SessionFactoryImpl.java:238) at org.hibernate.cfg.Configuration.buildSessionFactory(Configuration.java:1304) at org.springframework.orm.hibernate3.LocalSessionFactoryBean.newSessionFactory(LocalSessionFactoryBean.java:813) at org.springframework.orm.hibernate3.LocalSessionFactoryBean.buildSessionFactory(LocalSessionFactoryBean.java:731) at org.springframework.orm.hibernate3.AbstractSessionFactoryBean.afterPropertiesSet(AbstractSessionFactoryBean.java:211) at org.springframework.beans.factory.support.AbstractAutowireCapableBeanFactory.invokeInitMethods(AbstractAutowireCapableBeanFactory.java:1454) at org.springframework.beans.factory.support.AbstractAutowireCapableBeanFactory.initializeBean(AbstractAutowireCapableBeanFactory.java:1392) ... 48 more Mar 12, 2010 5:32:28 PM org.apache.catalina.core.StandardContext start SEVERE: Error listenerStart

  Read the article

• Java HotSpot 1.6 VM, Garbage Collection - Scary PermGen

  - by Gala101

  Hi, My app shows rising 'Old Generation'/'Tenured Generation' size, and when this reaches the max limit for 'Old Gen', then suddenly PermGen size increases. Here are my generation sizings: -Xmx1200m -Xms1200m -Xmn450m -XX:MaxPermSize=600m -XX:+UseParallelGC This is on 32 bit Fedora so can't have a bigger heap than this. The app is not doing any fancy classloading, though it is using Spring IOC and Hibernate, the Spring App-context.xml defines some 1000 Beans. This app starts with 175MB PermGen, which steadily increases to ~250MB in few hrs, stays that way till Tenured Generation reached ~780 MB, then permgen jumps to ~500MB while Old Gen drops to ~500MB. This forces me to restart the App on daily basis, and gives me real scare of looming OutOfMemory Error.. Any insights would be very helpful. Thanks Gala101

  Read the article

• QueryPerformanceCounter Not Working Properly on Amazon EC2 with Win Server 2008

  - by timeitquery

  Our application makes use of QueryPerformanceCounter to measure timings. When running it on Amazon EC2 instances we are noticing number that are out of whack. The symptoms look very similar to what has been reported with virtualized machines on HP proreliant servers, however all the articles state that this was not the case for Windows Server 2008. The articles recommended modifing the boot.ini to /USEPMTIMER - however, this seem to be missing from the documentation on bcdedit - which replaced boot.ini

  Read the article

• Should I update an application when a used framework release a new version?

  - by Alex

  I have an application that use several libraries and frameworks, should I update my application to use the latest version of those frameworks when a new stable version is available? For example, migrate from python 2.x to python 3.x, or from spring 2.5 to spring 3.0, but the question es very general, not language specific. If I keep the application updated to use the latest stable frameworks versions then I will have new features available in case I need them. If I don't, then may be in a future I will need to do the update and it will be a lot of work to update the application. Is there any best practice about this?

  Read the article

• Java Framework Choice Question.

  - by Sarang

  We do have many frameworks available in Java. Struts, Swing, JSF 2.0, Spring etc are used as per their priority. Actually, I don't know how many they are as well! But, as I am fresher to Java, even learning after their architecture, I cannot decide which framework can be used with what type of Projects ! Also, I am confused with mixed use of framework like Spring + JSF. What is the benefit to it ? Another thing making me confusing is about the UI components available in market. Like, we do have Primefaces, Ice-faces, MyFaces, Rich-faces. They may or may not have been supporting AJAX in-built. They may contains some bugs as well. What is best choice for Framework + UI component that can directly provide a best feet solution for any project ?

  Read the article

• Is frameworks really necessary for this problem?

  - by The Elite Gentleman

  Hi Guys I'm creating an online music store application (in Java) for signed and unsigned artist for my client. I'm currently using Struts 1.3.10 (I was recommended Spring but Spring setup is sort of similar to Struts) for my Web application. My Database is currently a MySQL 5 (or higher) and I'm using a DAO pattern to talk to it. There are limitations to using Struts and DAO's (e.g. Multiple File upload in Struts is not implemented the same way as multiple String parameters, and for DAO's, there lacks a Publish-Subscribe feature). Is what I'm doing the best way forward or should I go straight Hibernate (or similar) and move out of Struts? What are the performance implications or technical issues that you've experienced with the same setup I have? The client doesn't care how I do it as long as it is done.

  Read the article

• Selecting a radio button when a dropdown value changes

  - by Tim F.

  My setup is something like this: radiobutton1 - selection1 radiobutton2 - selection2 textinput1 I want radiobutton1 to be selected whenever selection1 is changed, and I want radiobutton2 to be selected whenever either selection2 or textinput1 is changed. There has to be a simple javascript solution here... I just can't find it. Here's my actual code ("$semopt" is a string holding the html code for the options on the first selection input): <input type='radio' name='semester' value='existing'/>Existing semester: <select name='sem_id'">$semopt </select><br/> <input type='radio' name='semester' value='new'/>New Semester: <select name='sem_name'"> <option value='Fall'>Fall</option> <option value='Spring'>Spring</option> </select> <input name='sem_year' value='$thisyear' size='5'"/><br/>

  Read the article

• Maven: Multiple class with the same path implemented in different jar

  - by Phuong Nguyen de ManCity fan

  I'm running into trouble with having multiple class with the same path (i.e. same name, same package!!!). For some reason, gwt-dev comes with its own version of org.apache.xerces.jaxp.DocumentBuilderFactoryImpl and javax.xml.parsers.DocumentBuilderFactory. At the same time, spring also depends on these classes but from different jar. I don't know what should be, but look like xalan & xml-api are the two dependencies that spring depends on (these dependency are optional) Funny thing is that eclipse can run the same code (it's a unit test) without problem, but surefire cannot. So I guess the problem is due to the way each runner consider the priority of each jar. Now come to the question: How can I setup my POM so that I can sure that when ever any code running inside my app, then class from a jar will be selected over class from other jar? Thanks.

  Read the article

• Is there an easy to integrate java-based forum software available

  - by miceuz

  Integration via Hibernate, Acegi, Spring, Tiles would be superb.

  Read the article

• Best approach to creating a database driven Java website?

  - by Craig Whitley

  I'm fairly new to programming and new to java, but I'd like to jump in the deep end with a little database driven website project. I've read quite a lot about requirements in the 'real world' requesting experience with Spring and Hibernate, so I have those installed on netbeans and a project created (if I hit run I get the default spring page). Now I just need a little guidance as to where to start designing my app (please tell me if I'm getting in a bit too over my head for a beginner!). Should I start off with my classes? - create all my classes as they map to my database tables and decide which attributes and methods each will require? Can anyone suggest any good books for maybe.. making a java based website from scratch (i.e. from design right through to deployment) that might be useful for a beginner? Any help appreciated thanks.

  Read the article

• How easy would it be to refactor a small JSP/Servlet/JDBC project to SpringMVC/Hibernate

  - by John

  With reference to this post, I am considering starting a new web-based Java project. Since I don't know Spring/Hibernate I was concerned if it's a bad plan to start learning them while creating a new project, especially since it will slow down the early development. One idea I had was to write a prototype using tech I do know, namely JSP/Servlets/JDBC, since I can get this running much quicker with my current knowledge. I could then throw the whole thing away and start over with Spring, etc, but I'd like to consider how easy it would be to refactor a smallish project from JSP/Servlets/JDB to SpringMVC/Hibernate? My DB could of course be re-used but what about other code... would I expect to save most of it plugged into an MVC framework, or is the paradigm shift big enough this would cause more trouble than it avoids? Please use the other question for more general advice on choosing technologies

  Read the article

• File uploading using sdk3?

  - by kumar1425

  How do I upload files using sdk3? I'm developing my project using flex and spring

  Read the article

• Automating Solaris 11 Zones Installation Using The Automated Install Server

  - by Orgad Kimchi

  Introduction How to use the Oracle Solaris 11 Automated install server in order to automate the Solaris 11 Zones installation. In this document I will demonstrate how to setup the Automated Install server in order to provide hands off installation process for the Global Zone and two Non Global Zones located on the same system. Architecture layout: Figure 1. Architecture layout Prerequisite Setup the Automated install server (AI) using the following instructions “How to Set Up Automated Installation Services for Oracle Solaris 11” The first step in this setup will be creating two Solaris 11 Zones configuration files. Step 1: Create the Solaris 11 Zones configuration files  The Solaris Zones configuration files should be in the format of the zonecfg export command. # zonecfg -z zone1 export > /var/tmp/zone1# cat /var/tmp/zone1 create -b set brand=solaris set zonepath=/rpool/zones/zone1 set autoboot=true set ip-type=exclusive add anet set linkname=net0 set lower-link=auto set configure-allowed-address=true set link-protection=mac-nospoof set mac-address=random end  Create a backup copy of this file under a different name, for example, zone2. # cp /var/tmp/zone1 /var/tmp/zone2 Modify the second configuration file with the zone2 configuration information You should change the zonepath for example: set zonepath=/rpool/zones/zone2 Step2: Copy and share the Zones configuration files  Create the NFS directory for the Zones configuration files # mkdir /export/zone_config Share the directory for the Zones configuration file # share –o ro /export/zone_config Copy the Zones configuration files into the NFS shared directory # cp /var/tmp/zone1 /var/tmp/zone2  /export/zone_config Verify that the NFS share has been created using the following command # share export_zone_config      /export/zone_config     nfs     sec=sys,ro Step 3: Add the Global Zone as client to the Install Service Use the installadm create-client command to associate client (Global Zone) with the install service To find the MAC address of a system, use the dladm command as described in the dladm(1M) man page. The following command adds the client (Global Zone) with MAC address 0:14:4f:2:a:19 to the s11x86service install service. # installadm create-client -e “0:14:4f:2:a:19" -n s11x86service You can verify the client creation using the following command # installadm list –c Service Name  Client Address     Arch   Image Path ------------  --------------     ----   ---------- s11x86service 00:14:4F:02:0A:19  i386   /export/auto_install/s11x86service We can see the client install service name (s11x86service), MAC address (00:14:4F:02:0A:19 and Architecture (i386). Step 4: Global Zone manifest setup  First, get a list of the installation services and the manifests associated with them: # installadm list -m Service Name   Manifest        Status ------------   --------        ------ default-i386   orig_default   Default s11x86service  orig_default   Default Then probe the s11x86service and the default manifest associated with it. The -m switch reflects the name of the manifest associated with a service. Since we want to capture that output into a file, we redirect the output of the command as follows: # installadm export -n s11x86service -m orig_default >  /var/tmp/orig_default.xml Create a backup copy of this file under a different name, for example, orig-default2.xml, and edit the copy. # cp /var/tmp/orig_default.xml /var/tmp/orig_default2.xml Use the configuration element in the AI manifest for the client system to specify non-global zones. Use the name attribute of the configuration element to specify the name of the zone. Use the source attribute to specify the location of the config file for the zone.The source location can be any http:// or file:// location that the client can access during installation. The following sample AI manifest specifies two Non-Global Zones: zone1 and zone2 You should replace the server_ip with the ip address of the NFS server. <!DOCTYPE auto_install SYSTEM "file:///usr/share/install/ai.dtd.1"> <auto_install>   <ai_instance>     <target>       <logical>         <zpool name="rpool" is_root="true">           <filesystem name="export" mountpoint="/export"/>           <filesystem name="export/home"/>           <be name="solaris"/>         </zpool>       </logical>     </target>     <software type="IPS">       <source>         <publisher name="solaris">           <origin name="http://pkg.oracle.com/solaris/release"/>         </publisher>       </source>       <software_data action="install">         <name>pkg:/entire@latest</name>         <name>pkg:/group/system/solaris-large-server</name>       </software_data>     </software>     <configuration type="zone" name="zone1" source="file:///net/server_ip/export/zone_config/zone1"/>     <configuration type="zone" name="zone2" source="file:///net/server_ip/export/zone_config/zone2"/>   </ai_instance> </auto_install> The following example adds the /var/tmp/orig_default2.xml AI manifest to the s11x86service install service # installadm create-manifest -n s11x86service -f /var/tmp/orig_default2.xml -m gzmanifest You can verify the manifest creation using the following command # installadm list -n s11x86service  -m Service/Manifest Name  Status   Criteria ---------------------  ------   -------- s11x86service    orig_default        Default  None    gzmanifest          Inactive None We can see from the command output that the new manifest named gzmanifest has been created and associated with the s11x86service install service. Step 5: Non Global Zone manifest setup The AI manifest for non-global zone installation is similar to the AI manifest for installing the global zone. If you do not provide a custom AI manifest for a non-global zone, the default AI manifest for Zones is used The default AI manifest for Zones is available at /usr/share/auto_install/manifest/zone_default.xml. In this example we should use the default AI manifest for zones The following sample default AI manifest for zones # cat /usr/share/auto_install/manifest/zone_default.xml <?xml version="1.0" encoding="UTF-8"?> <!--  Copyright (c) 2011, 2012, Oracle and/or its affiliates. All rights reserved. --> <!DOCTYPE auto_install SYSTEM "file:///usr/share/install/ai.dtd.1"> <auto_install>     <ai_instance name="zone_default">         <target>             <logical>                 <zpool name="rpool">                     <!--                       Subsequent <filesystem> entries instruct an installer                       to create following ZFS datasets:                           <root_pool>/export         (mounted on /export)                           <root_pool>/export/home    (mounted on /export/home)                       Those datasets are part of standard environment                       and should be always created.                       In rare cases, if there is a need to deploy a zone                       without these datasets, either comment out or remove                       <filesystem> entries. In such scenario, it has to be also                       assured that in case of non-interactive post-install                       configuration, creation of initial user account is                       disabled in related system configuration profile.                       Otherwise the installed zone would fail to boot.                     -->                     <filesystem name="export" mountpoint="/export"/>                     <filesystem name="export/home"/>                     <be name="solaris">                         <options>                             <option name="compression" value="on"/>                         </options>                     </be>                 </zpool>             </logical>         </target>         <software type="IPS">             <destination>                 <image>                     <!-- Specify locales to install -->                     <facet set="false">facet.locale.*</facet>                     <facet set="true">facet.locale.de</facet>                     <facet set="true">facet.locale.de_DE</facet>                     <facet set="true">facet.locale.en</facet>                     <facet set="true">facet.locale.en_US</facet>                     <facet set="true">facet.locale.es</facet>                     <facet set="true">facet.locale.es_ES</facet>                     <facet set="true">facet.locale.fr</facet>                     <facet set="true">facet.locale.fr_FR</facet>                     <facet set="true">facet.locale.it</facet>                     <facet set="true">facet.locale.it_IT</facet>                     <facet set="true">facet.locale.ja</facet>                     <facet set="true">facet.locale.ja_*</facet>                     <facet set="true">facet.locale.ko</facet>                     <facet set="true">facet.locale.ko_*</facet>                     <facet set="true">facet.locale.pt</facet>                     <facet set="true">facet.locale.pt_BR</facet>                     <facet set="true">facet.locale.zh</facet>                     <facet set="true">facet.locale.zh_CN</facet>                     <facet set="true">facet.locale.zh_TW</facet>                 </image>             </destination>             <software_data action="install">                 <name>pkg:/group/system/solaris-small-server</name>             </software_data>         </software>     </ai_instance> </auto_install> (optional) We can customize the default AI manifest for Zones Create a backup copy of this file under a different name, for example, zone_default2.xml and edit the copy # cp /usr/share/auto_install/manifest/zone_default.xml /var/tmp/zone_default2.xml Edit the copy (/var/tmp/zone_default2.xml) The following example adds the /var/tmp/zone_default2.xml AI manifest to the s11x86service install service and specifies that zone1 and zone2 should use this manifest. # installadm create-manifest -n s11x86service -f /var/tmp/zone_default2.xml -m zones_manifest -c zonename="zone1 zone2" Note: Do not use the following elements or attributes in a non-global zone AI manifest:     The auto_reboot attribute of the ai_instance element     The http_proxy attribute of the ai_instance element     The disk child element of the target element     The noswap attribute of the logical element     The nodump attribute of the logical element     The configuration element Step 6: Global Zone profile setup We are going to create a global zone configuration profile which includes the host information for example: host name, ip address name services etc… # sysconfig create-profile –o /var/tmp/gz_profile.xml You need to provide the host information for example:     Default router     Root password     DNS information The output should eventually disappear and be replaced by the initial screen of the System Configuration Tool (see Figure 2), where you can do the final configuration. Figure 2. Profile creation menu You can validate the profile using the following command # installadm validate -n s11x86service –P /var/tmp/gz_profile.xml Validating static profile gz_profile.xml...  Passed Next, instantiate a profile with the install service. In our case, use the following syntax for doing this # installadm create-profile -n s11x86service  -f /var/tmp/gz_profile.xml -p  gz_profile You can verify profile creation using the following command # installadm list –n s11x86service  -p Service/Profile Name  Criteria --------------------  -------- s11x86service    gz_profile         None We can see that the gz_profie has been created and associated with the s11x86service Install service. Step 7: Setup the Solaris Zones configuration profiles The step should be similar to the Global zone profile creation on step 6 # sysconfig create-profile –o /var/tmp/zone1_profile.xml # sysconfig create-profile –o /var/tmp/zone2_profile.xml You can validate the profiles using the following command # installadm validate -n s11x86service -P /var/tmp/zone1_profile.xml Validating static profile zone1_profile.xml...  Passed # installadm validate -n s11x86service -P /var/tmp/zone2_profile.xml Validating static profile zone2_profile.xml...  Passed Next, associate the profiles with the install service The following example adds the zone1_profile.xml configuration profile to the s11x86service  install service and specifies that zone1 should use this profile. # installadm create-profile -n s11x86service  -f  /var/tmp/zone1_profile.xml -p zone1_profile -c zonename=zone1 The following example adds the zone2_profile.xml configuration profile to the s11x86service  install service and specifies that zone2 should use this profile. # installadm create-profile -n s11x86service  -f  /var/tmp/zone2_profile.xml -p zone2_profile -c zonename=zone2 You can verify the profiles creation using the following command # installadm list -n s11x86service -p Service/Profile Name  Criteria --------------------  -------- s11x86service    zone1_profile      zonename = zone1    zone2_profile      zonename = zone2    gz_profile         None We can see that we have three profiles in the s11x86service  install service     Global Zone  gz_profile     zone1            zone1_profile     zone2            zone2_profile. Step 8: Global Zone setup Associate the global zone client with the manifest and the profile that we create in the previous steps The following example adds the manifest and profile to the client (global zone), where: gzmanifest  is the name of the manifest. gz_profile  is the name of the configuration profile. mac="0:14:4f:2:a:19" is the client (global zone) mac address s11x86service is the install service name. # installadm set-criteria -m  gzmanifest  –p  gz_profile  -c mac="0:14:4f:2:a:19" -n s11x86service You can verify the manifest and profile association using the following command # installadm list -n s11x86service -p  -m Service/Manifest Name  Status   Criteria ---------------------  ------   -------- s11x86service    gzmanifest                   mac  = 00:14:4F:02:0A:19    orig_default        Default  None Service/Profile Name  Criteria --------------------  -------- s11x86service    gz_profile         mac      = 00:14:4F:02:0A:19    zone2_profile      zonename = zone2    zone1_profile      zonename = zone1 Step 9: Provision the host with the Non-Global Zones The next step is to boot the client system off the network and provision it using the Automated Install service that we just set up. First, boot the client system. Figure 3 shows the network boot attempt (when done on an x86 system): Figure 3. Network Boot Then you will be prompted by a GRUB menu, with a timer, as shown in Figure 4. The default selection (the "Text Installer and command line" option) is highlighted.  Press the down arrow to highlight the second option labeled Automated Install, and then press Enter. The reason we need to do this is because we want to prevent a system from being automatically re-installed if it were to be booted from the network accidentally. Figure 4. GRUB Menu What follows is the continuation of a networked boot from the Automated Install server,. The client downloads a mini-root (a small set of files in which to successfully run the installer), identifies the location of the Automated Install manifest on the network, retrieves that manifest, and then processes it to identify the address of the IPS repository from which to obtain the desired software payload. Non-Global Zones are installed and configured on the first reboot after the Global Zone is installed. You can list all the Solaris Zones status using the following command # zoneadm list -civ Once the Zones are in running state you can login into the Zone using the following command # zlogin –z zone1 Troubleshooting Automated Installations If an installation to a client system failed, you can find the client log at /system/volatile/install_log. NOTE: Zones are not installed if any of the following errors occurs:     A zone config file is not syntactically correct.     A collision exists among zone names, zone paths, or delegated ZFS datasets in the set of zones to be installed     Required datasets are not configured in the global zone. For more troubleshooting information see “Installing Oracle Solaris 11 Systems” Conclusion This paper demonstrated the benefits of using the Automated Install server to simplify the Non Global Zones setup, including the creation and configuration of the global zone manifest and the Solaris Zones profiles.

  Read the article

• rsyslogd not monitoring all files

  - by Tom O'Connor

  So.. I've installed Logstash, and instead of using the logstash shipper (because it needs the JVM and is generally massive), I'm using rsyslogd with the following configuration. # Use traditional timestamp format $ActionFileDefaultTemplate RSYSLOG_TraditionalFileFormat $IncludeConfig /etc/rsyslog.d/*.conf # Provides kernel logging support (previously done by rklogd) $ModLoad imklog # Provides support for local system logging (e.g. via logger command) $ModLoad imuxsock # Log all kernel messages to the console. # Logging much else clutters up the screen. #kern.* /dev/console # Log anything (except mail) of level info or higher. # Don't log private authentication messages! *.info;mail.none;authpriv.none;cron.none;local6.none /var/log/messages # The authpriv file has restricted access. authpriv.* /var/log/secure # Log all the mail messages in one place. mail.* -/var/log/maillog # Log cron stuff cron.* /var/log/cron # Everybody gets emergency messages *.emerg * # Save news errors of level crit and higher in a special file. uucp,news.crit /var/log/spooler # Save boot messages also to boot.log local7.* /var/log/boot.log In /etc/rsyslog.d/logstash.conf there are 28 file monitor blocks using imfile $ModLoad imfile # Load the imfile input module $ModLoad imklog # for reading kernel log messages $ModLoad imuxsock # for reading local syslog messages $InputFileName /var/log/rabbitmq/startup_err $InputFileTag rmq-err: $InputFileStateFile state-rmq-err $InputFileFacility local6 $InputRunFileMonitor .... $InputFileName /var/log/some.other.custom.log $InputFileTag cust-log: $InputFileStateFile state-cust-log $InputFileFacility local6 $InputRunFileMonitor .... *.* @@10.90.0.110:5514 There are 28 InputFileMonitor blocks, each monitoring a different custom application logfile.. If I run [root@secret-gm02 ~]# lsof|grep rsyslog rsyslogd 5380 root cwd DIR 253,0 4096 2 / rsyslogd 5380 root rtd DIR 253,0 4096 2 / rsyslogd 5380 root txt REG 253,0 278976 1015955 /sbin/rsyslogd rsyslogd 5380 root mem REG 253,0 58400 1868123 /lib64/libgcc_s-4.1.2-20080825.so.1 rsyslogd 5380 root mem REG 253,0 144776 1867778 /lib64/ld-2.5.so rsyslogd 5380 root mem REG 253,0 1718232 1867780 /lib64/libc-2.5.so rsyslogd 5380 root mem REG 253,0 23360 1867787 /lib64/libdl-2.5.so rsyslogd 5380 root mem REG 253,0 145872 1867797 /lib64/libpthread-2.5.so rsyslogd 5380 root mem REG 253,0 85544 1867815 /lib64/libz.so.1.2.3 rsyslogd 5380 root mem REG 253,0 53448 1867801 /lib64/librt-2.5.so rsyslogd 5380 root mem REG 253,0 92816 1868016 /lib64/libresolv-2.5.so rsyslogd 5380 root mem REG 253,0 20384 1867990 /lib64/rsyslog/lmnsd_ptcp.so rsyslogd 5380 root mem REG 253,0 53880 1867802 /lib64/libnss_files-2.5.so rsyslogd 5380 root mem REG 253,0 23736 1867800 /lib64/libnss_dns-2.5.so rsyslogd 5380 root mem REG 253,0 20768 1867988 /lib64/rsyslog/lmnet.so rsyslogd 5380 root mem REG 253,0 11488 1867982 /lib64/rsyslog/imfile.so rsyslogd 5380 root mem REG 253,0 24040 1867983 /lib64/rsyslog/imklog.so rsyslogd 5380 root mem REG 253,0 11536 1867987 /lib64/rsyslog/imuxsock.so rsyslogd 5380 root mem REG 253,0 13152 1867989 /lib64/rsyslog/lmnetstrms.so rsyslogd 5380 root mem REG 253,0 8400 1867992 /lib64/rsyslog/lmtcpclt.so rsyslogd 5380 root 0r REG 0,3 0 4026531848 /proc/kmsg rsyslogd 5380 root 1u IPv4 1200589517 0t0 TCP 10.10.10.90 t:40629->10.10.10.90:5514 (ESTABLISHED) rsyslogd 5380 root 2u IPv4 1200589527 0t0 UDP *:45801 rsyslogd 5380 root 3w REG 253,3 17999744 2621483 /var/log/messages rsyslogd 5380 root 4w REG 253,3 13383 2621484 /var/log/secure rsyslogd 5380 root 5w REG 253,3 7180 2621493 /var/log/maillog rsyslogd 5380 root 6w REG 253,3 43321 2621529 /var/log/cron rsyslogd 5380 root 7w REG 253,3 0 2621494 /var/log/spooler rsyslogd 5380 root 8w REG 253,3 0 2621495 /var/log/boot.log rsyslogd 5380 root 9r REG 253,3 1064271998 2621464 /var/log/custom-application.monolog.log rsyslogd 5380 root 10u unix 0xffff81081fad2e40 0t0 1200589511 /dev/log You can see that there are nowhere near 28 logfiles actually being read. I really had to get one file monitored, so I moved it to the top, and it picked it up, but I'd like to be able to monitor all 28+ files, and not have to worry. OS is Centos 5.5 Kernel 2.6.18-308.el5 rsyslogd 3.22.1, compiled with: FEATURE_REGEXP: Yes FEATURE_LARGEFILE: Yes FEATURE_NETZIP (message compression): Yes GSSAPI Kerberos 5 support: Yes FEATURE_DEBUG (debug build, slow code): No Atomic operations supported: Yes Runtime Instrumentation (slow code): No Questions: Why is rsyslogd only monitoring a very small subset of the files? How can I fix this so that all the files are monitored?

  Read the article

• Windows 8 Stuck on Start Screen File Search

  - by baturayd

  I have been searching someone else having the same issue but I couldn't find any. Here is my problem: I'm using Windows 8 Pro with Media Center. File search screen does not close itself after I make a file search within start screen. It stuck on that screen. I can't go back to desktop, therefore, task manager is inaccessible. Only way to get out of it is to sign out. It also looks like non-operational. It doesn't give me any result at all. It's just a blank screen with "Files" title. It used to work perfectly. Things I have done before coming here: Safe mode minimal boot to ensure no other 3rd party software interferes. sfc haven't found any inconsistencies. Search index has been rebuild. Normal boot with all 3rd party services and start-up items disabled. System restore to a date that I know this feature was functional. And by the way, I have installed all updates released so far. I strongly used file search via start menu back in Windows 7. This is an absolute game changer for me. I'm curious what causes this. I'll do a "system refresh" if I can't fix this. I'm working on it, I'll keep this thread updated should I find any fix. First update: I just discovered that file search screen gets stuck if it's invoked by typing query directly in start screen. It doesn't get stuck if it's invoked from win + x menu. I was able to "escape" from stuck screen with invoking it again by win + x menu. After rebuilding search index again, search suggestions started to appear again but still there is no file search functionality. Second update: "Results for" expression appears only for a second near to "Files" title when search is initialized. Third update: As a last resort, I finally tried to do a "System Refresh" which has also failed to refresh by giving an error after waiting almost 20 minutes at 99%. (Seriously?) After cold boot it began to undo changes. After changes were reverted, I boot the machine without doing anything further and bingo! Search began acting normal again. This is a totally weird solution. It obviously fixed certain system files during failed refresh, and kept those changes untouched because they were supposed to be that way at the first place. I'll keep this thread alive should anyone comes with a more logical explanation. Forth update: After a windows update, search functionality again stopped responding. It happened after a system update for the first time. Now I have a pretty good suspicion about system update, though I have no solid proof of its involvement with this problem.

  Read the article

• Solaris 11.1: Changes to included FOSS packages

  - by alanc

  Besides the documentation changes I mentioned last time, another place you can see Solaris 11.1 changes before upgrading is in the online package repository, now that the 11.1 packages have been published to http://pkg.oracle.com/solaris/release/, as the “0.175.1.0.0.24.2” branch. (Oracle Solaris Package Versioning explains what each field in that version string means.) When you’re ready to upgrade to the packages from either this repo, or the support repository, you’ll want to first read How to Update to Oracle Solaris 11.1 Using the Image Packaging System by Pete Dennis, as there are a couple issues you will need to be aware of to do that upgrade, several of which are due to changes in the Free and Open Source Software (FOSS) packages included with Solaris, as I’ll explain in a bit. Solaris 11 can update more readily than Solaris 10 In the Solaris 10 and older update models, the way the updates were built constrained what changes we could make in those releases. To change an existing SVR4 package in those releases, we created a Solaris Patch, which applied to a given version of the SVR4 package and replaced, added or deleted files in it. These patches were released via the support websites (originally SunSolve, now My Oracle Support) for applying to existing Solaris 10 installations, and were also merged into the install images for the next Solaris 10 update release. (This Solaris Patches blog post from Gerry Haskins dives deeper into that subject.) Some of the restrictions of this model were that package refactoring, changes to package dependencies, and even just changing the package version number, were difficult to do in this hybrid patch/OS update model. For instance, when Solaris 10 first shipped, it had the Xorg server from X11R6.8. Over the first couple years of update releases we were able to keep it up to date by replacing, adding, & removing files as necessary, taking it all the way up to Xorg server release 1.3 (new version numbering begun after the X11R7 split of the X11 tree into separate modules gave each module its own version). But if you run pkginfo on the SUNWxorg-server package, you’ll see it still displayed a version number of 6.8, confusing users as to which version was actually included. We stopped upgrading the Xorg server releases in Solaris 10 after 1.3, as later versions added new dependencies, such as HAL, D-Bus, and libpciaccess, which were very difficult to manage in this patching model. (We later got libpciaccess to work, but HAL & D-Bus would have been much harder due to the greater dependency tree underneath those.) Similarly, every time the GNOME team looked into upgrading Solaris 10 past GNOME 2.6, they found these constraints made it so difficult it wasn’t worthwhile, and eventually GNOME’s dependencies had changed enough it was completely infeasible. Fortunately, this worked out for both the X11 & GNOME teams, with our management making the business decision to concentrate on the “Nevada” branch for desktop users - first as Solaris Express Desktop Edition, and later as OpenSolaris, so we didn’t have to fight to try to make the package updates fit into these tight constraints. Meanwhile, the team designing the new packaging system for Solaris 11 was seeing us struggle with these problems, and making this much easier to manage for both the development teams and our users was one of their big goals for the IPS design they were working on. Now that we’ve reached the first update release to Solaris 11, we can start to see the fruits of their labors, with more FOSS updates in 11.1 than we had in many Solaris 10 update releases, keeping software more up to date with the upstream communities. Of course, just because we can more easily update now, doesn’t always mean we should or will do so, it just removes the package system limitations from forcing the decision for us. So while we’ve upgraded the X Window System in the 11.1 release from X11R7.6 to 7.7, the Solaris GNOME team decided it was not the right time to try to make the jump from GNOME 2 to GNOME 3, though they did update some individual components of the desktop, especially those with security fixes like Firefox. In other parts of the system, decisions as to what to update were prioritized based on how they affected other projects, or what customer requests we’d gotten for them. So with all that background in place, what packages did we actually update or add between Solaris 11.0 and 11.1? Core OS Functionality One of the FOSS changes with the biggest impact in this release is the upgrade from Grub Legacy (0.97) to Grub 2 (1.99) for the x64 platform boot loader. This is the cause of one of the upgrade quirks, since to go from Solaris 11.0 to 11.1 on x64 systems, you first need to update the Boot Environment tools (such as beadm) to a new version that can handle boot environments that use the Grub2 boot loader. System administrators can find the details they need to know about the new Grub in the Administering the GRand Unified Bootloader chapter of the Booting and Shutting Down Oracle Solaris 11.1 Systems guide. This change was necessary to be able to support new hardware coming into the x64 marketplace, including systems using UEFI firmware or booting off disk drives larger than 2 terabytes. For both platforms, Solaris 11.1 adds rsyslog as an optional alternative to the traditional syslogd, and OpenSCAP for checking security configuration settings are compliant with site policies. Note that the support repo actually has newer versions of BIND & fetchmail than the 11.1 release, as some late breaking critical fixes came through from the community upstream releases after the Solaris 11.1 release was frozen, and made their way to the support repository. These are responsible for the other big upgrade quirk in this release, in which to upgrade a system which already installed those versions from the support repo, you need to either wait for those packages to make their way to the 11.1 branch of the support repo, or follow the steps in the aforementioned upgrade walkthrough to let the package system know it's okay to temporarily downgrade those. Developer Stack While Solaris 11.0 included Python 2.7, many of the bundled python modules weren’t packaged for it yet, limiting its usability. For 11.1, many more of the python modules include 2.7 versions (enough that I filtered them out of the below table, but you can always search on the package repository server for them. For other language runtimes and development tools, 11.1 expands the use of IPS mediated links to choose which version of a package is the default when the packages are designed to allow multiple versions to install side by side. For instance, in Solaris 11.0, GNU automake 1.9 and 1.10 were provided, and developers had to run them as either automake-1.9 or automake-1.10. In Solaris 11.1, when automake 1.11 was added, also added was a /usr/bin/automake mediated link, which points to the automake-1.11 program by default, but can be changed to another version by running the pkg set-mediator command. Mediated links were also used for the Java runtime & development kits in 11.1, changing the default versions to the Java 7 releases (the 1.7.0.x package versions), while allowing admins to switch links such as /usr/bin/javac back to Java 6 if they need to for their site, to deal with Java 7 compatibility or other issues, without having to update each usage to use the full versioned /usr/jdk/jdk1.6.0_35/bin/javac paths for every invocation. Desktop Stack As I mentioned before, we upgraded from X11R7.6 to X11R7.7, since a pleasant coincidence made the X.Org release dates line up nicely with our feature & code freeze dates for this release. (Or perhaps it wasn’t so coincidental, after all, one of the benefits of being the person making the release is being able to decide what schedule is most convenient for you, and this one worked well for me.) For the table below, I’ve skipped listing the packages in which we use the X11 “katamari” version for the Solaris package version (mainly packages combining elements of multiple upstream modules with independent version numbers), since they just all changed from 7.6 to 7.7. In the graphics drivers, we worked with Intel to update the Intel Integrated Graphics Processor support to support 3D graphics and kernel mode setting on the Ivy Bridge chipsets, and updated Nvidia’s non-FOSS graphics driver from 280.13 to 295.20. Higher up in the desktop stack, PulseAudio was added for audio support, and liblouis for Braille support, and the GNOME applications were built to use them. The Mozilla applications, Firefox & Thunderbird moved to the current Extended Support Release (ESR) versions, 10.x for each, to bring up-to-date security fixes without having to be on Mozilla’s agressive 6 week feature cycle release train. Detailed list of changes This table shows most of the changes to the FOSS packages between Solaris 11.0 and 11.1. As noted above, some were excluded for clarity, or to reduce noise and duplication. All the FOSS packages which didn't change the version number in their packaging info are not included, even if they had updates to fix bugs, security holes, or add support for new hardware or new features of Solaris. Package11.011.1 archiver/unrar 3.8.5 4.1.4 audio/sox 14.3.0 14.3.2 backup/rdiff-backup 1.2.1 1.3.3 communication/im/pidgin 2.10.0 2.10.5 compress/gzip 1.3.5 1.4 compress/xz not included 5.0.1 database/sqlite-3 3.7.6.3 3.7.11 desktop/remote-desktop/tigervnc 1.0.90 1.1.0 desktop/window-manager/xcompmgr 1.1.5 1.1.6 desktop/xscreensaver 5.12 5.15 developer/build/autoconf 2.63 2.68 developer/build/autoconf/xorg-macros 1.15.0 1.17 developer/build/automake-111 not included 1.11.2 developer/build/cmake 2.6.2 2.8.6 developer/build/gnu-make 3.81 3.82 developer/build/imake 1.0.4 1.0.5 developer/build/libtool 1.5.22 2.4.2 developer/build/makedepend 1.0.3 1.0.4 developer/documentation-tool/doxygen 1.5.7.1 1.7.6.1 developer/gnu-binutils 2.19 2.21.1 developer/java/jdepend not included 2.9 developer/java/jdk-6 1.6.0.26 1.6.0.35 developer/java/jdk-7 1.7.0.0 1.7.0.7 developer/java/jpackage-utils not included 1.7.5 developer/java/junit 4.5 4.10 developer/lexer/jflex not included 1.4.1 developer/parser/byaccj not included 1.14 developer/parser/java_cup not included 0.10 developer/quilt 0.47 0.60 developer/versioning/git 1.7.3.2 1.7.9.2 developer/versioning/mercurial 1.8.4 2.2.1 developer/versioning/subversion 1.6.16 1.7.5 diagnostic/constype 1.0.3 1.0.4 diagnostic/nmap 5.21 5.51 diagnostic/scanpci 0.12.1 0.13.1 diagnostic/wireshark 1.4.8 1.8.2 diagnostic/xload 1.1.0 1.1.1 editor/gnu-emacs 23.1 23.4 editor/vim 7.3.254 7.3.600 file/lndir 1.0.2 1.0.3 image/editor/bitmap 1.0.5 1.0.6 image/gnuplot 4.4.0 4.6.0 image/library/libexif 0.6.19 0.6.21 image/library/libpng 1.4.8 1.4.11 image/library/librsvg 2.26.3 2.34.1 image/xcursorgen 1.0.4 1.0.5 library/audio/pulseaudio not included 1.1 library/cacao 2.3.0.0 2.3.1.0 library/expat 2.0.1 2.1.0 library/gc 7.1 7.2 library/graphics/pixman 0.22.0 0.24.4 library/guile 1.8.4 1.8.6 library/java/javadb 10.5.3.0 10.6.2.1 library/java/subversion 1.6.16 1.7.5 library/json-c not included 0.9 library/libedit not included 3.0 library/libee not included 0.3.2 library/libestr not included 0.1.2 library/libevent 1.3.5 1.4.14.2 library/liblouis not included 2.1.1 library/liblouisxml not included 2.1.0 library/libtecla 1.6.0 1.6.1 library/libtool/libltdl 1.5.22 2.4.2 library/nspr 4.8.8 4.8.9 library/openldap 2.4.25 2.4.30 library/pcre 7.8 8.21 library/perl-5/subversion 1.6.16 1.7.5 library/python-2/jsonrpclib not included 0.1.3 library/python-2/lxml 2.1.2 2.3.3 library/python-2/nose not included 1.1.2 library/python-2/pyopenssl not included 0.11 library/python-2/subversion 1.6.16 1.7.5 library/python-2/tkinter-26 2.6.4 2.6.8 library/python-2/tkinter-27 2.7.1 2.7.3 library/security/nss 4.12.10 4.13.1 library/security/openssl 1.0.0.5 (1.0.0e) 1.0.0.10 (1.0.0j) mail/thunderbird 6.0 10.0.6 network/dns/bind 9.6.3.4.3 9.6.3.7.2 package/pkgbuild not included 1.3.104 print/filter/enscript not included 1.6.4 print/filter/gutenprint 5.2.4 5.2.7 print/lp/filter/foomatic-rip 3.0.2 4.0.15 runtime/java/jre-6 1.6.0.26 1.6.0.35 runtime/java/jre-7 1.7.0.0 1.7.0.7 runtime/perl-512 5.12.3 5.12.4 runtime/python-26 2.6.4 2.6.8 runtime/python-27 2.7.1 2.7.3 runtime/ruby-18 1.8.7.334 1.8.7.357 runtime/tcl-8/tcl-sqlite-3 3.7.6.3 3.7.11 security/compliance/openscap not included 0.8.1 security/nss-utilities 4.12.10 4.13.1 security/sudo 1.8.1.2 1.8.4.5 service/network/dhcp/isc-dhcp 4.1 4.1.0.6 service/network/dns/bind 9.6.3.4.3 9.6.3.7.2 service/network/ftp (ProFTPD) 1.3.3.0.5 1.3.3.0.7 service/network/samba 3.5.10 3.6.6 shell/conflict 0.2004.9.1 0.2010.6.27 shell/pipe-viewer 1.1.4 1.2.0 shell/zsh 4.3.12 4.3.17 system/boot/grub 0.97 1.99 system/font/truetype/liberation 1.4 1.7.2 system/library/freetype-2 2.4.6 2.4.9 system/library/libnet 1.1.2.1 1.1.5 system/management/cim/pegasus 2.9.1 2.11.0 system/management/ipmitool 1.8.10 1.8.11 system/management/wbem/wbemcli 1.3.7 1.3.9.1 system/network/routing/quagga 0.99.8 0.99.19 system/rsyslog not included 6.2.0 terminal/luit 1.1.0 1.1.1 text/convmv 1.14 1.15 text/gawk 3.1.5 3.1.8 text/gnu-grep 2.5.4 2.10 web/browser/firefox 6.0.2 10.0.6 web/browser/links 1.0 1.0.3 web/java-servlet/tomcat 6.0.33 6.0.35 web/php-53 not included 5.3.14 web/php-53/extension/php-apc not included 3.1.9 web/php-53/extension/php-idn not included 0.2.0 web/php-53/extension/php-memcache not included 3.0.6 web/php-53/extension/php-mysql not included 5.3.14 web/php-53/extension/php-pear not included 5.3.14 web/php-53/extension/php-suhosin not included 0.9.33 web/php-53/extension/php-tcpwrap not included 1.1.3 web/php-53/extension/php-xdebug not included 2.2.0 web/php-common not included 11.1 web/proxy/squid 3.1.8 3.1.18 web/server/apache-22 2.2.20 2.2.22 web/server/apache-22/module/apache-sed 2.2.20 2.2.22 web/server/apache-22/module/apache-wsgi not included 3.3 x11/diagnostic/xev 1.1.0 1.2.0 x11/diagnostic/xscope 1.3 1.3.1 x11/documentation/xorg-docs 1.6 1.7 x11/keyboard/xkbcomp 1.2.3 1.2.4 x11/library/libdmx 1.1.1 1.1.2 x11/library/libdrm 2.4.25 2.4.32 x11/library/libfontenc 1.1.0 1.1.1 x11/library/libfs 1.0.3 1.0.4 x11/library/libice 1.0.7 1.0.8 x11/library/libsm 1.2.0 1.2.1 x11/library/libx11 1.4.4 1.5.0 x11/library/libxau 1.0.6 1.0.7 x11/library/libxcb 1.7 1.8.1 x11/library/libxcursor 1.1.12 1.1.13 x11/library/libxdmcp 1.1.0 1.1.1 x11/library/libxext 1.3.0 1.3.1 x11/library/libxfixes 4.0.5 5.0 x11/library/libxfont 1.4.4 1.4.5 x11/library/libxft 2.2.0 2.3.1 x11/library/libxi 1.4.3 1.6.1 x11/library/libxinerama 1.1.1 1.1.2 x11/library/libxkbfile 1.0.7 1.0.8 x11/library/libxmu 1.1.0 1.1.1 x11/library/libxmuu 1.1.0 1.1.1 x11/library/libxpm 3.5.9 3.5.10 x11/library/libxrender 0.9.6 0.9.7 x11/library/libxres 1.0.5 1.0.6 x11/library/libxscrnsaver 1.2.1 1.2.2 x11/library/libxtst 1.2.0 1.2.1 x11/library/libxv 1.0.6 1.0.7 x11/library/libxvmc 1.0.6 1.0.7 x11/library/libxxf86vm 1.1.1 1.1.2 x11/library/mesa 7.10.2 7.11.2 x11/library/toolkit/libxaw7 1.0.9 1.0.11 x11/library/toolkit/libxt 1.0.9 1.1.3 x11/library/xtrans 1.2.6 1.2.7 x11/oclock 1.0.2 1.0.3 x11/server/xdmx 1.10.3 1.12.2 x11/server/xephyr 1.10.3 1.12.2 x11/server/xorg 1.10.3 1.12.2 x11/server/xorg/driver/xorg-input-keyboard 1.6.0 1.6.1 x11/server/xorg/driver/xorg-input-mouse 1.7.1 1.7.2 x11/server/xorg/driver/xorg-input-synaptics 1.4.1 1.6.2 x11/server/xorg/driver/xorg-input-vmmouse 12.7.0 12.8.0 x11/server/xorg/driver/xorg-video-ast 0.91.10 0.93.10 x11/server/xorg/driver/xorg-video-ati 6.14.1 6.14.4 x11/server/xorg/driver/xorg-video-cirrus 1.3.2 1.4.0 x11/server/xorg/driver/xorg-video-dummy 0.3.4 0.3.5 x11/server/xorg/driver/xorg-video-intel 2.10.0 2.18.0 x11/server/xorg/driver/xorg-video-mach64 6.9.0 6.9.1 x11/server/xorg/driver/xorg-video-mga 1.4.13 1.5.0 x11/server/xorg/driver/xorg-video-openchrome 0.2.904 0.2.905 x11/server/xorg/driver/xorg-video-r128 6.8.1 6.8.2 x11/server/xorg/driver/xorg-video-trident 1.3.4 1.3.5 x11/server/xorg/driver/xorg-video-vesa 2.3.0 2.3.1 x11/server/xorg/driver/xorg-video-vmware 11.0.3 12.0.2 x11/server/xserver-common 1.10.3 1.12.2 x11/server/xvfb 1.10.3 1.12.2 x11/server/xvnc 1.0.90 1.1.0 x11/session/sessreg 1.0.6 1.0.7 x11/session/xauth 1.0.6 1.0.7 x11/session/xinit 1.3.1 1.3.2 x11/transset 0.9.1 1.0.0 x11/trusted/trusted-xorg 1.10.3 1.12.2 x11/x11-window-dump 1.0.4 1.0.5 x11/xclipboard 1.1.1 1.1.2 x11/xclock 1.0.5 1.0.6 x11/xfd 1.1.0 1.1.1 x11/xfontsel 1.0.3 1.0.4 x11/xfs 1.1.1 1.1.2 P.S. To get the version numbers for this table, I ran a quick perl script over the output from: % pkg contents -H -r -t depend -a type=incorporate -o fmri \ `pkg contents -H -r -t depend -a type=incorporate -o fmri [email protected],5.11-0.175.1.0.0.24` \ | sort /tmp/11.1 % pkg contents -H -r -t depend -a type=incorporate -o fmri \ `pkg contents -H -r -t depend -a type=incorporate -o fmri [email protected],5.11-0.175.0.0.0.2` \ | sort /tmp/11.0

  Read the article

• Why didn't 12.04 install?

  - by Josephisscrewed

  Ok, so I've installed Ubuntu many times on my computer.. Normally on the same partition, and WIndows would always delete Ubuntu(I don't know how.. it just happens) if i go away from keyboard during boot and it chooses Windows automatically because I took to long. So i tried to reinstall again, but after the fifth time it wouldn't let me, and told me to check "wubi-12.04-rev266.log". It took a while to find, but when i found it, I had no idea what any of it meant, as I'm no programmer.I first tried this the day Precise Pangolin came out. SO skip ahead 2.5 months, when I finally found this file, and i then got the idea of making a new partition to install Ubuntu on, but I used wubi, like I always did. It didn't look like it would f anything up, so I did it. it went through all the downloads, extracting, etc. Which took about 40 minutes total, then ended with an error message saying to check "wubi-12.04-rev266.log". i did. Here's what it says: 07-10 23:33 INFO root: === wubi 12.04 rev266 === 07-10 23:33 DEBUG root: Logfile is c:\users\joseph\appdata\local\temp\wubi-12.04-rev266.log 07-10 23:33 DEBUG root: sys.argv = ['main.pyo', '--exefile="C:\\Users\\Joseph\\Downloads\\wubi.exe"'] 07-10 23:33 DEBUG CommonBackend: data_dir=C:\Users\Joseph\AppData\Local\Temp\pylA05E.tmp\data 07-10 23:33 DEBUG WindowsBackend: 7z=C:\Users\Joseph\AppData\Local\Temp\pylA05E.tmp\bin\7z.exe 07-10 23:33 DEBUG WindowsBackend: startup_folder=C:\ProgramData\Microsoft\Windows\Start Menu\Programs\Startup 07-10 23:33 DEBUG CommonBackend: Fetching basic info... 07-10 23:33 DEBUG CommonBackend: original_exe=C:\Users\Joseph\Downloads\wubi.exe 07-10 23:33 DEBUG CommonBackend: platform=win32 07-10 23:33 DEBUG CommonBackend: osname=nt 07-10 23:33 DEBUG CommonBackend: language=en_US 07-10 23:33 DEBUG CommonBackend: encoding=cp1252 07-10 23:33 DEBUG WindowsBackend: arch=amd64 07-10 23:33 DEBUG CommonBackend: Parsing isolist=C:\Users\Joseph\AppData\Local\Temp\pylA05E.tmp\data\isolist.ini 07-10 23:33 DEBUG CommonBackend: Adding distro Xubuntu-i386 07-10 23:33 DEBUG CommonBackend: Adding distro Edubuntu-i386 07-10 23:33 DEBUG CommonBackend: Adding distro Xubuntu-amd64 07-10 23:33 DEBUG CommonBackend: Adding distro Kubuntu-amd64 07-10 23:33 DEBUG CommonBackend: Adding distro Mythbuntu-i386 07-10 23:33 DEBUG CommonBackend: Adding distro Edubuntu-amd64 07-10 23:33 DEBUG CommonBackend: Adding distro Ubuntu-amd64 07-10 23:33 DEBUG CommonBackend: Adding distro Lubuntu-i386 07-10 23:33 DEBUG CommonBackend: Adding distro Ubuntu-i386 07-10 23:33 DEBUG CommonBackend: Adding distro Mythbuntu-amd64 07-10 23:33 DEBUG CommonBackend: Adding distro Kubuntu-i386 07-10 23:33 DEBUG CommonBackend: Adding distro Lubuntu-amd64 07-10 23:33 DEBUG WindowsBackend: Fetching host info... 07-10 23:33 DEBUG WindowsBackend: registry_key=Software\Microsoft\Windows\CurrentVersion\Uninstall\Wubi 07-10 23:33 DEBUG WindowsBackend: windows version=vista 07-10 23:33 DEBUG WindowsBackend: windows_version2=Windows 7 Home Premium 07-10 23:33 DEBUG WindowsBackend: windows_sp=None 07-10 23:33 DEBUG WindowsBackend: windows_build=7600 07-10 23:33 DEBUG WindowsBackend: gmt=-8 07-10 23:33 DEBUG WindowsBackend: country=US 07-10 23:33 DEBUG WindowsBackend: timezone=America/Los_Angeles 07-10 23:33 DEBUG WindowsBackend: windows_username=Joseph 07-10 23:33 DEBUG WindowsBackend: user_full_name=Joseph 07-10 23:33 DEBUG WindowsBackend: user_directory=C:\Users\Joseph 07-10 23:33 DEBUG WindowsBackend: windows_language_code=1033 07-10 23:33 DEBUG WindowsBackend: windows_language=English 07-10 23:33 DEBUG WindowsBackend: processor_name=Intel(R) Core(TM) i3 CPU M 370 @ 2.40GHz 07-10 23:33 DEBUG WindowsBackend: bootloader=vista 07-10 23:33 DEBUG WindowsBackend: system_drive=Drive(C: hd 78696.8203125 mb free ntfs) 07-10 23:33 DEBUG WindowsBackend: drive=Drive(C: hd 78696.8203125 mb free ntfs) 07-10 23:33 DEBUG WindowsBackend: drive=Drive(D: hd 4303.48046875 mb free ntfs) 07-10 23:33 DEBUG WindowsBackend: drive=Drive(E: cd 0.0 mb free udf) 07-10 23:33 DEBUG WindowsBackend: drive=Drive(U: hd 79907.8320313 mb free ntfs) 07-10 23:33 DEBUG WindowsBackend: uninstaller_path=None 07-10 23:33 DEBUG WindowsBackend: previous_target_dir=None 07-10 23:33 DEBUG WindowsBackend: previous_distro_name=None 07-10 23:33 DEBUG WindowsBackend: keyboard_id=67699721 07-10 23:33 DEBUG WindowsBackend: keyboard_layout=us 07-10 23:33 DEBUG WindowsBackend: keyboard_variant= 07-10 23:33 DEBUG CommonBackend: python locale=('en_US', 'cp1252') 07-10 23:33 DEBUG CommonBackend: locale=en_US.UTF-8 07-10 23:33 DEBUG WindowsBackend: total_memory_mb=3893.859375 07-10 23:33 DEBUG CommonBackend: Searching ISOs on USB devices 07-10 23:33 DEBUG CommonBackend: Searching for local CDs 07-10 23:33 DEBUG Distro: checking whether C:\Users\Joseph\AppData\Local\Temp\pylA05E.tmp is a valid Ubuntu CD 07-10 23:33 DEBUG Distro: does not contain C:\Users\Joseph\AppData\Local\Temp\pylA05E.tmp\casper\filesystem.squashfs 07-10 23:33 DEBUG Distro: checking whether C:\Users\Joseph\AppData\Local\Temp\pylA05E.tmp is a valid Ubuntu CD 07-10 23:33 DEBUG Distro: does not contain C:\Users\Joseph\AppData\Local\Temp\pylA05E.tmp\casper\filesystem.squashfs 07-10 23:33 DEBUG Distro: checking whether C:\Users\Joseph\AppData\Local\Temp\pylA05E.tmp is a valid Kubuntu CD 07-10 23:33 DEBUG Distro: does not contain C:\Users\Joseph\AppData\Local\Temp\pylA05E.tmp\casper\filesystem.squashfs 07-10 23:33 DEBUG Distro: checking whether C:\Users\Joseph\AppData\Local\Temp\pylA05E.tmp is a valid Kubuntu CD 07-10 23:33 DEBUG Distro: does not contain C:\Users\Joseph\AppData\Local\Temp\pylA05E.tmp\casper\filesystem.squashfs 07-10 23:33 DEBUG Distro: checking whether C:\Users\Joseph\AppData\Local\Temp\pylA05E.tmp is a valid Xubuntu CD 07-10 23:33 DEBUG Distro: does not contain C:\Users\Joseph\AppData\Local\Temp\pylA05E.tmp\casper\filesystem.squashfs 07-10 23:33 DEBUG Distro: checking whether C:\Users\Joseph\AppData\Local\Temp\pylA05E.tmp is a valid Xubuntu CD 07-10 23:33 DEBUG Distro: does not contain C:\Users\Joseph\AppData\Local\Temp\pylA05E.tmp\casper\filesystem.squashfs 07-10 23:33 DEBUG Distro: checking whether C:\Users\Joseph\AppData\Local\Temp\pylA05E.tmp is a valid Mythbuntu CD 07-10 23:33 DEBUG Distro: does not contain C:\Users\Joseph\AppData\Local\Temp\pylA05E.tmp\casper\filesystem.squashfs 07-10 23:33 DEBUG Distro: checking whether C:\Users\Joseph\AppData\Local\Temp\pylA05E.tmp is a valid Mythbuntu CD 07-10 23:33 DEBUG Distro: does not contain C:\Users\Joseph\AppData\Local\Temp\pylA05E.tmp\casper\filesystem.squashfs 07-10 23:33 DEBUG Distro: checking whether C:\Users\Joseph\AppData\Local\Temp\pylA05E.tmp is a valid Edubuntu CD 07-10 23:33 DEBUG Distro: does not contain C:\Users\Joseph\AppData\Local\Temp\pylA05E.tmp\casper\filesystem.squashfs 07-10 23:33 DEBUG Distro: checking whether C:\Users\Joseph\AppData\Local\Temp\pylA05E.tmp is a valid Edubuntu CD 07-10 23:33 DEBUG Distro: does not contain C:\Users\Joseph\AppData\Local\Temp\pylA05E.tmp\casper\filesystem.squashfs 07-10 23:33 DEBUG Distro: checking whether C:\Users\Joseph\AppData\Local\Temp\pylA05E.tmp is a valid Lubuntu CD 07-10 23:33 DEBUG Distro: does not contain C:\Users\Joseph\AppData\Local\Temp\pylA05E.tmp\casper\filesystem.squashfs 07-10 23:33 DEBUG Distro: checking whether C:\Users\Joseph\AppData\Local\Temp\pylA05E.tmp is a valid Lubuntu CD 07-10 23:33 DEBUG Distro: does not contain C:\Users\Joseph\AppData\Local\Temp\pylA05E.tmp\casper\filesystem.squashfs 07-10 23:33 DEBUG Distro: checking whether D:\ is a valid Ubuntu CD 07-10 23:33 DEBUG Distro: does not contain D:\casper\filesystem.squashfs 07-10 23:33 DEBUG Distro: checking whether D:\ is a valid Ubuntu CD 07-10 23:33 DEBUG Distro: does not contain D:\casper\filesystem.squashfs 07-10 23:33 DEBUG Distro: checking whether D:\ is a valid Kubuntu CD 07-10 23:33 DEBUG Distro: does not contain D:\casper\filesystem.squashfs 07-10 23:33 DEBUG Distro: checking whether D:\ is a valid Kubuntu CD 07-10 23:33 DEBUG Distro: does not contain D:\casper\filesystem.squashfs 07-10 23:33 DEBUG Distro: checking whether D:\ is a valid Xubuntu CD 07-10 23:33 DEBUG Distro: does not contain D:\casper\filesystem.squashfs 07-10 23:33 DEBUG Distro: checking whether D:\ is a valid Xubuntu CD 07-10 23:33 DEBUG Distro: does not contain D:\casper\filesystem.squashfs 07-10 23:33 DEBUG Distro: checking whether D:\ is a valid Mythbuntu CD 07-10 23:33 DEBUG Distro: does not contain D:\casper\filesystem.squashfs 07-10 23:33 DEBUG Distro: checking whether D:\ is a valid Mythbuntu CD 07-10 23:33 DEBUG Distro: does not contain D:\casper\filesystem.squashfs 07-10 23:33 DEBUG Distro: checking whether D:\ is a valid Edubuntu CD 07-10 23:33 DEBUG Distro: does not contain D:\casper\filesystem.squashfs 07-10 23:33 DEBUG Distro: checking whether D:\ is a valid Edubuntu CD 07-10 23:33 DEBUG Distro: does not contain D:\casper\filesystem.squashfs 07-10 23:33 DEBUG Distro: checking whether D:\ is a valid Lubuntu CD 07-10 23:33 DEBUG Distro: does not contain D:\casper\filesystem.squashfs 07-10 23:33 DEBUG Distro: checking whether D:\ is a valid Lubuntu CD 07-10 23:33 DEBUG Distro: does not contain D:\casper\filesystem.squashfs 07-10 23:33 DEBUG Distro: checking whether E:\ is a valid Ubuntu CD 07-10 23:33 DEBUG Distro: does not contain E:\casper\filesystem.squashfs 07-10 23:33 DEBUG Distro: checking whether E:\ is a valid Ubuntu CD 07-10 23:33 DEBUG Distro: does not contain E:\casper\filesystem.squashfs 07-10 23:33 DEBUG Distro: checking whether E:\ is a valid Kubuntu CD 07-10 23:33 DEBUG Distro: does not contain E:\casper\filesystem.squashfs 07-10 23:33 DEBUG Distro: checking whether E:\ is a valid Kubuntu CD 07-10 23:33 DEBUG Distro: does not contain E:\casper\filesystem.squashfs 07-10 23:33 DEBUG Distro: checking whether E:\ is a valid Xubuntu CD 07-10 23:33 DEBUG Distro: does not contain E:\casper\filesystem.squashfs 07-10 23:33 DEBUG Distro: checking whether E:\ is a valid Xubuntu CD 07-10 23:33 DEBUG Distro: does not contain E:\casper\filesystem.squashfs 07-10 23:33 DEBUG Distro: checking whether E:\ is a valid Mythbuntu CD 07-10 23:33 DEBUG Distro: does not contain E:\casper\filesystem.squashfs 07-10 23:33 DEBUG Distro: checking whether E:\ is a valid Mythbuntu CD 07-10 23:33 DEBUG Distro: does not contain E:\casper\filesystem.squashfs 07-10 23:33 DEBUG Distro: checking whether E:\ is a valid Edubuntu CD 07-10 23:33 DEBUG Distro: does not contain E:\casper\filesystem.squashfs 07-10 23:33 DEBUG Distro: checking whether E:\ is a valid Edubuntu CD 07-10 23:33 DEBUG Distro: does not contain E:\casper\filesystem.squashfs 07-10 23:33 DEBUG Distro: checking whether E:\ is a valid Lubuntu CD 07-10 23:33 DEBUG Distro: does not contain E:\casper\filesystem.squashfs 07-10 23:33 DEBUG Distro: checking whether E:\ is a valid Lubuntu CD 07-10 23:33 DEBUG Distro: does not contain E:\casper\filesystem.squashfs 07-10 23:33 DEBUG Distro: checking whether U:\ is a valid Ubuntu CD 07-10 23:33 DEBUG Distro: does not contain U:\casper\filesystem.squashfs 07-10 23:33 DEBUG Distro: checking whether U:\ is a valid Ubuntu CD 07-10 23:33 DEBUG Distro: does not contain U:\casper\filesystem.squashfs 07-10 23:33 DEBUG Distro: checking whether U:\ is a valid Kubuntu CD 07-10 23:33 DEBUG Distro: does not contain U:\casper\filesystem.squashfs 07-10 23:33 DEBUG Distro: checking whether U:\ is a valid Kubuntu CD 07-10 23:33 DEBUG Distro: does not contain U:\casper\filesystem.squashfs 07-10 23:33 DEBUG Distro: checking whether U:\ is a valid Xubuntu CD 07-10 23:33 DEBUG Distro: does not contain U:\casper\filesystem.squashfs 07-10 23:33 DEBUG Distro: checking whether U:\ is a valid Xubuntu CD 07-10 23:33 DEBUG Distro: does not contain U:\casper\filesystem.squashfs 07-10 23:33 DEBUG Distro: checking whether U:\ is a valid Mythbuntu CD 07-10 23:33 DEBUG Distro: does not contain U:\casper\filesystem.squashfs 07-10 23:33 DEBUG Distro: checking whether U:\ is a valid Mythbuntu CD 07-10 23:33 DEBUG Distro: does not contain U:\casper\filesystem.squashfs 07-10 23:33 DEBUG Distro: checking whether U:\ is a valid Edubuntu CD 07-10 23:33 DEBUG Distro: does not contain U:\casper\filesystem.squashfs 07-10 23:33 DEBUG Distro: checking whether U:\ is a valid Edubuntu CD 07-10 23:33 DEBUG Distro: does not contain U:\casper\filesystem.squashfs 07-10 23:33 DEBUG Distro: checking whether U:\ is a valid Lubuntu CD 07-10 23:33 DEBUG Distro: does not contain U:\casper\filesystem.squashfs 07-10 23:33 DEBUG Distro: checking whether U:\ is a valid Lubuntu CD 07-10 23:33 DEBUG Distro: does not contain U:\casper\filesystem.squashfs 07-10 23:33 INFO root: Running the installer... 07-10 23:33 DEBUG WindowsFrontend: __init__... 07-10 23:33 DEBUG WindowsFrontend: on_init... 07-10 23:33 INFO WinuiPage: appname=wubi, localedir=C:\Users\Joseph\AppData\Local\Temp\pylA05E.tmp\translations, languages=['en_US', 'en'] 07-10 23:33 INFO WinuiPage: appname=wubi, localedir=C:\Users\Joseph\AppData\Local\Temp\pylA05E.tmp\translations, languages=['en_US', 'en'] 07-10 23:35 DEBUG WinuiInstallationPage: target_drive=U:, installation_size=30000MB, distro_name=Ubuntu, language=en_US, locale=en_US.UTF-8, username=joseph 07-10 23:35 INFO root: Received settings 07-10 23:35 DEBUG CommonBackend: Searching for local CD 07-10 23:35 DEBUG Distro: checking whether C:\Users\Joseph\AppData\Local\Temp\pylA05E.tmp is a valid Ubuntu CD 07-10 23:35 DEBUG Distro: does not contain C:\Users\Joseph\AppData\Local\Temp\pylA05E.tmp\casper\filesystem.squashfs 07-10 23:35 DEBUG Distro: checking whether D:\ is a valid Ubuntu CD 07-10 23:35 DEBUG Distro: does not contain D:\casper\filesystem.squashfs 07-10 23:35 DEBUG Distro: checking whether E:\ is a valid Ubuntu CD 07-10 23:35 DEBUG Distro: does not contain E:\casper\filesystem.squashfs 07-10 23:35 DEBUG Distro: checking whether U:\ is a valid Ubuntu CD 07-10 23:35 DEBUG Distro: does not contain U:\casper\filesystem.squashfs 07-10 23:35 DEBUG CommonBackend: Searching for local ISO 07-10 23:35 INFO WinuiPage: appname=wubi, localedir=C:\Users\Joseph\AppData\Local\Temp\pylA05E.tmp\translations, languages=['en_US', 'en'] 07-10 23:35 DEBUG TaskList: # Running tasklist... 07-10 23:35 DEBUG TaskList: ## Running select_target_dir... 07-10 23:35 INFO WindowsBackend: Installing into U:\ubuntu 07-10 23:35 DEBUG TaskList: ## Finished select_target_dir 07-10 23:35 DEBUG TaskList: ## Running create_dir_structure... 07-10 23:35 DEBUG CommonBackend: Creating dir U:\ubuntu 07-10 23:35 DEBUG CommonBackend: Creating dir U:\ubuntu\disks 07-10 23:35 DEBUG CommonBackend: Creating dir U:\ubuntu\install 07-10 23:35 DEBUG CommonBackend: Creating dir U:\ubuntu\install\boot 07-10 23:35 DEBUG CommonBackend: Creating dir U:\ubuntu\disks\boot 07-10 23:35 DEBUG CommonBackend: Creating dir U:\ubuntu\disks\boot\grub 07-10 23:35 DEBUG CommonBackend: Creating dir U:\ubuntu\install\boot\grub 07-10 23:35 DEBUG TaskList: ## Finished create_dir_structure 07-10 23:35 DEBUG TaskList: ## Running create_uninstaller... 07-10 23:35 DEBUG WindowsBackend: Copying uninstaller C:\Users\Joseph\Downloads\wubi.exe -> U:\ubuntu\uninstall-wubi.exe 07-10 23:35 DEBUG registry: Setting registry key -2147483646 Software\Microsoft\Windows\CurrentVersion\Uninstall\Wubi UninstallString U:\ubuntu\uninstall-wubi.exe 07-10 23:35 DEBUG registry: Setting registry key -2147483646 Software\Microsoft\Windows\CurrentVersion\Uninstall\Wubi InstallationDir U:\ubuntu 07-10 23:35 DEBUG registry: Setting registry key -2147483646 Software\Microsoft\Windows\CurrentVersion\Uninstall\Wubi DisplayName Ubuntu 07-10 23:35 DEBUG registry: Setting registry key -2147483646 Software\Microsoft\Windows\CurrentVersion\Uninstall\Wubi DisplayIcon U:\ubuntu\Ubuntu.ico 07-10 23:35 DEBUG registry: Setting registry key -2147483646 Software\Microsoft\Windows\CurrentVersion\Uninstall\Wubi DisplayVersion 12.04-rev266 07-10 23:35 DEBUG registry: Setting registry key -2147483646 Software\Microsoft\Windows\CurrentVersion\Uninstall\Wubi Publisher Ubuntu 07-10 23:35 DEBUG registry: Setting registry key -2147483646 Software\Microsoft\Windows\CurrentVersion\Uninstall\Wubi URLInfoAbout http://www.ubuntu.com 07-10 23:35 DEBUG registry: Setting registry key -2147483646 Software\Microsoft\Windows\CurrentVersion\Uninstall\Wubi HelpLink http://www.ubuntu.com/support 07-10 23:35 DEBUG TaskList: ## Finished create_uninstaller 07-10 23:35 DEBUG TaskList: ## Running create_preseed_diskimage... 07-10 23:35 DEBUG TaskList: ## Finished create_preseed_diskimage 07-10 23:35 DEBUG TaskList: ## Running get_diskimage... 07-10 23:35 DEBUG TaskList: New task download 07-10 23:35 DEBUG TaskList: ### Running download... 07-10 23:35 DEBUG downloader: downloading http://releases.ubuntu.com/12.04/ubuntu-12.04-wubi-amd64.tar.xz > U:\ubuntu\disks\ubuntu-12.04-wubi-amd64.tar.xz 07-10 23:35 DEBUG downloader: Download start filename=U:\ubuntu\disks\ubuntu-12.04-wubi-amd64.tar.xz, url=http://releases.ubuntu.com/12.04/ubuntu-12.04-wubi-amd64.tar.xz, basename=ubuntu-12.04-wubi-amd64.tar.xz, length=512730488, text=None 07-11 00:00 DEBUG TaskList: ### Finished download 07-11 00:00 DEBUG downloader: download finished (read 512730488 bytes) 07-11 00:00 DEBUG TaskList: ## Finished get_diskimage 07-11 00:00 DEBUG TaskList: ## Running extract_diskimage... 07-11 00:03 DEBUG TaskList: ## Finished extract_diskimage 07-11 00:03 DEBUG TaskList: ## Running choose_disk_sizes... 07-11 00:03 DEBUG WindowsBackend: total size=30000 root=29744 swap=256 home=0 usr=0 07-11 00:03 DEBUG TaskList: ## Finished choose_disk_sizes 07-11 00:03 DEBUG TaskList: ## Running expand_diskimage... 07-11 00:05 DEBUG TaskList: ## Finished expand_diskimage 07-11 00:05 DEBUG TaskList: ## Running create_swap_diskimage... 07-11 00:05 DEBUG TaskList: ## Finished create_swap_diskimage 07-11 00:05 DEBUG TaskList: ## Running modify_bootloader... 07-11 00:05 DEBUG TaskList: New task modify_bcd 07-11 00:05 DEBUG TaskList: ### Running modify_bcd... 07-11 00:05 DEBUG WindowsBackend: modify_bcd Drive(C: hd 78696.8203125 mb free ntfs) 07-11 00:05 ERROR TaskList: Error executing command >>command=C:\Windows\sysnative\bcdedit.exe /set {970e3d1b-e019-11df-a016-81045c79c1f9} device partition=U: >>retval=1 >>stderr=An error has occurred setting the element data. The request is not supported. >>stdout= Traceback (most recent call last): File "\lib\wubi\backends\common\tasklist.py", line 197, in __call__ File "\lib\wubi\backends\win32\backend.py", line 697, in modify_bcd File "\lib\wubi\backends\common\utils.py", line 66, in run_command Exception: Error executing command >>command=C:\Windows\sysnative\bcdedit.exe /set {970e3d1b-e019-11df-a016-81045c79c1f9} device partition=U: >>retval=1 >>stderr=An error has occurred setting the element data. The request is not supported. >>stdout= 07-11 00:05 DEBUG TaskList: # Cancelling tasklist 07-11 00:05 DEBUG TaskList: New task modify_bcd 07-11 00:05 ERROR root: Error executing command >>command=C:\Windows\sysnative\bcdedit.exe /set {970e3d1b-e019-11df-a016-81045c79c1f9} device partition=U: >>retval=1 >>stderr=An error has occurred setting the element data. The request is not supported. >>stdout= Traceback (most recent call last): File "\lib\wubi\application.py", line 58, in run File "\lib\wubi\application.py", line 132, in select_task File "\lib\wubi\application.py", line 158, in run_installer File "\lib\wubi\backends\common\tasklist.py", line 197, in __call__ File "\lib\wubi\backends\win32\backend.py", line 697, in modify_bcd File "\lib\wubi\backends\common\utils.py", line 66, in run_command Exception: Error executing command >>command=C:\Windows\sysnative\bcdedit.exe /set {970e3d1b-e019-11df-a016-81045c79c1f9} device partition=U: >>retval=1 >>stderr=An error has occurred setting the element data. The request is not supported. >>stdout= 07-11 00:05 DEBUG TaskList: New task modify_bcd 07-11 00:05 DEBUG TaskList: ## Finished modify_bootloader 07-11 00:05 DEBUG TaskList: # Finished tasklist What have I done wrong? What can I do? If I turn off my laptop, will I actually be able to turn it back on? If you want me to post the log from the first day it happened, i'd be glad to in the comments, in the main body it made it over 30000 characters.

  Read the article

• lxc containers hangs after upgrade to 13.10

  - by doug123

  I have 3 lxc containers. They were all working fine on 12.10 and I upgraded the containers with do-release-upgrade on the containers to 13.04 and 13.10 and that worked great. Then I upgraded the host to 13.04 and then 13.10 and now the 3 containers hang with this: >lxc-start -n as1 -l DEBUG -o $(tty) lxc-start 1383145786.513 INFO lxc_start_ui - using rcfile /var/lib/lxc/as1/config lxc-start 1383145786.513 WARN lxc_log - lxc_log_init called with log already initialized lxc-start 1383145786.513 INFO lxc_apparmor - aa_enabled set to 1 lxc-start 1383145786.514 DEBUG lxc_conf - allocated pty '/dev/pts/2' (5/6) lxc-start 1383145786.514 DEBUG lxc_conf - allocated pty '/dev/pts/13' (7/8) lxc-start 1383145786.514 DEBUG lxc_conf - allocated pty '/dev/pts/14' (9/10) lxc-start 1383145786.514 DEBUG lxc_conf - allocated pty '/dev/pts/15' (11/12) lxc-start 1383145786.514 DEBUG lxc_conf - allocated pty '/dev/pts/17' (13/14) lxc-start 1383145786.514 DEBUG lxc_conf - allocated pty '/dev/pts/18' (15/16) lxc-start 1383145786.514 DEBUG lxc_conf - allocated pty '/dev/pts/19' (17/18) lxc-start 1383145786.514 DEBUG lxc_conf - allocated pty '/dev/pts/20' (19/20) lxc-start 1383145786.514 INFO lxc_conf - tty's configured lxc-start 1383145786.514 DEBUG lxc_start - sigchild handler set lxc-start 1383145786.514 DEBUG lxc_console - opening /dev/tty for console peer lxc-start 1383145786.514 DEBUG lxc_console - using '/dev/tty' as console lxc-start 1383145786.514 DEBUG lxc_console - 6242 got SIGWINCH fd 25 lxc-start 1383145786.514 DEBUG lxc_console - set winsz dstfd:22 cols:177 rows:53 lxc-start 1383145786.514 INFO lxc_start - 'as1' is initialized lxc-start 1383145786.522 DEBUG lxc_start - Not dropping cap_sys_boot or watching utmp lxc-start 1383145786.524 DEBUG lxc_conf - mac address of host interface 'vethB4L35W' changed to private fe:7c:96:a0:ae:29 lxc-start 1383145786.525 DEBUG lxc_conf - instanciated veth 'vethB4L35W/vethVC61K2', index is '26' lxc-start 1383145786.529 DEBUG lxc_cgroup - cgroup 'memory.limit_in_bytes' set to '20G' lxc-start 1383145786.529 DEBUG lxc_cgroup - cgroup 'cpuset.cpus' set to '12-23' lxc-start 1383145786.529 INFO lxc_cgroup - cgroup has been setup lxc-start 1383145786.555 DEBUG lxc_conf - move 'eth0' to '6249' lxc-start 1383145786.555 INFO lxc_conf - 'as1' hostname has been setup lxc-start 1383145786.575 DEBUG lxc_conf - 'eth0' has been setup lxc-start 1383145786.575 INFO lxc_conf - network has been setup lxc-start 1383145786.575 INFO lxc_conf - looking at .44 42 252:0 / / rw,relatime - ext4 /dev/mapper/limitorderbook1-root rw,errors=remount-ro,data=ordered . lxc-start 1383145786.575 INFO lxc_conf - now p is . /. lxc-start 1383145786.575 INFO lxc_conf - looking at .52 44 0:5 / /dev rw,relatime - devtmpfs udev rw,size=32961632k,nr_inodes=8240408,mode=755 . lxc-start 1383145786.575 INFO lxc_conf - now p is . /dev. lxc-start 1383145786.575 INFO lxc_conf - looking at .61 52 0:11 / /dev/pts rw,nosuid,noexec,relatime - devpts devpts rw,mode=600,ptmxmode=000 . lxc-start 1383145786.575 INFO lxc_conf - now p is . /dev/pts. lxc-start 1383145786.575 INFO lxc_conf - looking at .68 44 0:15 / /run rw,nosuid,noexec,relatime - tmpfs tmpfs rw,size=6594456k,mode=755 . lxc-start 1383145786.575 INFO lxc_conf - now p is . /run. lxc-start 1383145786.575 INFO lxc_conf - looking at .69 68 0:18 / /run/lock rw,nosuid,nodev,noexec,relatime - tmpfs none rw,size=5120k . lxc-start 1383145786.575 INFO lxc_conf - now p is . /run/lock. lxc-start 1383145786.575 INFO lxc_conf - looking at .72 68 0:19 / /run/shm rw,nosuid,nodev,relatime - tmpfs none rw . lxc-start 1383145786.575 INFO lxc_conf - now p is . /run/shm. lxc-start 1383145786.575 INFO lxc_conf - looking at .73 68 0:21 / /run/user rw,nosuid,nodev,noexec,relatime - tmpfs none rw,size=102400k,mode=755 . lxc-start 1383145786.575 INFO lxc_conf - now p is . /run/user. lxc-start 1383145786.575 INFO lxc_conf - looking at .76 44 0:14 / /sys rw,nosuid,nodev,noexec,relatime - sysfs sysfs rw . lxc-start 1383145786.575 INFO lxc_conf - now p is . /sys. lxc-start 1383145786.575 INFO lxc_conf - looking at .77 76 0:16 / /sys/fs/cgroup rw,relatime - tmpfs none rw,size=4k,mode=755 . lxc-start 1383145786.575 INFO lxc_conf - now p is . /sys/fs/cgroup. lxc-start 1383145786.575 INFO lxc_conf - looking at .78 77 0:20 / /sys/fs/cgroup/cpuset rw,relatime - cgroup cgroup rw,cpuset,clone_children . lxc-start 1383145786.575 INFO lxc_conf - now p is . /sys/fs/cgroup/cpuset. lxc-start 1383145786.575 INFO lxc_conf - looking at .79 77 0:23 / /sys/fs/cgroup/cpu rw,relatime - cgroup cgroup rw,cpu . lxc-start 1383145786.575 INFO lxc_conf - now p is . /sys/fs/cgroup/cpu. lxc-start 1383145786.575 INFO lxc_conf - looking at .80 77 0:24 / /sys/fs/cgroup/cpuacct rw,relatime - cgroup cgroup rw,cpuacct . lxc-start 1383145786.575 INFO lxc_conf - now p is . /sys/fs/cgroup/cpuacct. lxc-start 1383145786.575 INFO lxc_conf - looking at .81 77 0:25 / /sys/fs/cgroup/memory rw,relatime - cgroup cgroup rw,memory . lxc-start 1383145786.575 INFO lxc_conf - now p is . /sys/fs/cgroup/memory. lxc-start 1383145786.575 INFO lxc_conf - looking at .82 77 0:26 / /sys/fs/cgroup/devices rw,relatime - cgroup cgroup rw,devices . lxc-start 1383145786.575 INFO lxc_conf - now p is . /sys/fs/cgroup/devices. lxc-start 1383145786.575 INFO lxc_conf - looking at .83 77 0:27 / /sys/fs/cgroup/freezer rw,relatime - cgroup cgroup rw,freezer . lxc-start 1383145786.575 INFO lxc_conf - now p is . /sys/fs/cgroup/freezer. lxc-start 1383145786.575 INFO lxc_conf - looking at .84 77 0:28 / /sys/fs/cgroup/blkio rw,relatime - cgroup cgroup rw,blkio . lxc-start 1383145786.575 INFO lxc_conf - now p is . /sys/fs/cgroup/blkio. lxc-start 1383145786.575 INFO lxc_conf - looking at .85 77 0:29 / /sys/fs/cgroup/perf_event rw,relatime - cgroup cgroup rw,perf_event . lxc-start 1383145786.575 INFO lxc_conf - now p is . /sys/fs/cgroup/perf_event. lxc-start 1383145786.575 INFO lxc_conf - looking at .94 77 0:30 / /sys/fs/cgroup/hugetlb rw,relatime - cgroup cgroup rw,hugetlb . lxc-start 1383145786.575 INFO lxc_conf - now p is . /sys/fs/cgroup/hugetlb. lxc-start 1383145786.575 INFO lxc_conf - looking at .95 77 0:31 / /sys/fs/cgroup/systemd rw,nosuid,nodev,noexec,relatime - cgroup systemd rw,name=systemd . lxc-start 1383145786.575 INFO lxc_conf - now p is . /sys/fs/cgroup/systemd. lxc-start 1383145786.575 INFO lxc_conf - looking at .96 76 0:17 / /sys/fs/fuse/connections rw,relatime - fusectl none rw . lxc-start 1383145786.575 INFO lxc_conf - now p is . /sys/fs/fuse/connections. lxc-start 1383145786.575 INFO lxc_conf - looking at .98 76 0:6 / /sys/kernel/debug rw,relatime - debugfs none rw . lxc-start 1383145786.575 INFO lxc_conf - now p is . /sys/kernel/debug. lxc-start 1383145786.575 INFO lxc_conf - looking at .101 76 0:10 / /sys/kernel/security rw,relatime - securityfs none rw . lxc-start 1383145786.575 INFO lxc_conf - now p is . /sys/kernel/security. lxc-start 1383145786.575 INFO lxc_conf - looking at .102 76 0:22 / /sys/fs/pstore rw,relatime - pstore none rw . lxc-start 1383145786.575 INFO lxc_conf - now p is . /sys/fs/pstore. lxc-start 1383145786.575 INFO lxc_conf - looking at .103 44 0:3 / /proc rw,nosuid,nodev,noexec,relatime - proc proc rw . lxc-start 1383145786.575 INFO lxc_conf - now p is . /proc. lxc-start 1383145786.575 INFO lxc_conf - looking at .104 44 9:2 / /data rw,relatime - ext4 /dev/md2 rw,errors=remount-ro,data=ordered . lxc-start 1383145786.575 INFO lxc_conf - now p is . /data. lxc-start 1383145786.575 INFO lxc_conf - looking at .105 44 8:1 / /boot rw,relatime - ext2 /dev/sda1 rw,errors=continue . lxc-start 1383145786.575 INFO lxc_conf - now p is . /boot. lxc-start 1383145786.576 DEBUG lxc_conf - mounted '/data/srv/lxc/as1' on '/usr/lib/x86_64-linux-gnu/lxc' lxc-start 1383145786.576 DEBUG lxc_conf - mounted 'none' on '/usr/lib/x86_64-linux-gnu/lxc//dev/pts', type 'devpts' lxc-start 1383145786.576 DEBUG lxc_conf - mounted 'none' on '/usr/lib/x86_64-linux-gnu/lxc//proc', type 'proc' lxc-start 1383145786.576 DEBUG lxc_conf - mounted 'none' on '/usr/lib/x86_64-linux-gnu/lxc//sys', type 'sysfs' lxc-start 1383145786.576 DEBUG lxc_conf - mounted 'none' on '/usr/lib/x86_64-linux-gnu/lxc//run', type 'tmpfs' lxc-start 1383145786.576 INFO lxc_conf - mount points have been setup lxc-start 1383145786.577 INFO lxc_conf - console has been setup lxc-start 1383145786.577 INFO lxc_conf - 8 tty(s) has been setup lxc-start 1383145786.577 INFO lxc_conf - rootfs path is ./data/srv/lxc/as1., mount is ./usr/lib/x86_64-linux-gnu/lxc. lxc-start 1383145786.577 INFO lxc_apparmor - I am 1, /proc/self points to 1 lxc-start 1383145786.577 DEBUG lxc_conf - created '/usr/lib/x86_64-linux-gnu/lxc/lxc_putold' directory lxc-start 1383145786.577 DEBUG lxc_conf - mountpoint for old rootfs is '/usr/lib/x86_64-linux-gnu/lxc/lxc_putold' lxc-start 1383145786.577 DEBUG lxc_conf - pivot_root syscall to '/usr/lib/x86_64-linux-gnu/lxc' successful lxc-start 1383145786.577 DEBUG lxc_conf - umounted '/lxc_putold/dev/pts' lxc-start 1383145786.577 DEBUG lxc_conf - umounted '/lxc_putold/run/lock' lxc-start 1383145786.577 DEBUG lxc_conf - umounted '/lxc_putold/run/shm' lxc-start 1383145786.577 DEBUG lxc_conf - umounted '/lxc_putold/run/user' lxc-start 1383145786.577 DEBUG lxc_conf - umounted '/lxc_putold/sys/fs/cgroup/cpuset' lxc-start 1383145786.577 DEBUG lxc_conf - umounted '/lxc_putold/sys/fs/cgroup/cpu' lxc-start 1383145786.577 DEBUG lxc_conf - umounted '/lxc_putold/sys/fs/cgroup/cpuacct' lxc-start 1383145786.577 DEBUG lxc_conf - umounted '/lxc_putold/sys/fs/cgroup/memory' lxc-start 1383145786.577 DEBUG lxc_conf - umounted '/lxc_putold/sys/fs/cgroup/devices' lxc-start 1383145786.577 DEBUG lxc_conf - umounted '/lxc_putold/sys/fs/cgroup/freezer' lxc-start 1383145786.577 DEBUG lxc_conf - umounted '/lxc_putold/sys/fs/cgroup/blkio' lxc-start 1383145786.577 DEBUG lxc_conf - umounted '/lxc_putold/sys/fs/cgroup/perf_event' lxc-start 1383145786.577 DEBUG lxc_conf - umounted '/lxc_putold/sys/fs/cgroup/hugetlb' lxc-start 1383145786.577 DEBUG lxc_conf - umounted '/lxc_putold/sys/fs/cgroup/systemd' lxc-start 1383145786.577 DEBUG lxc_conf - umounted '/lxc_putold/sys/fs/fuse/connections' lxc-start 1383145786.577 DEBUG lxc_conf - umounted '/lxc_putold/sys/kernel/debug' lxc-start 1383145786.577 DEBUG lxc_conf - umounted '/lxc_putold/sys/kernel/security' lxc-start 1383145786.577 DEBUG lxc_conf - umounted '/lxc_putold/sys/fs/pstore' lxc-start 1383145786.577 DEBUG lxc_conf - umounted '/lxc_putold/proc' lxc-start 1383145786.577 DEBUG lxc_conf - umounted '/lxc_putold/data' lxc-start 1383145786.577 DEBUG lxc_conf - umounted '/lxc_putold/boot' lxc-start 1383145786.577 DEBUG lxc_conf - umounted '/lxc_putold/dev' lxc-start 1383145786.577 DEBUG lxc_conf - umounted '/lxc_putold/run' lxc-start 1383145786.577 DEBUG lxc_conf - umounted '/lxc_putold/sys/fs/cgroup' lxc-start 1383145786.577 DEBUG lxc_conf - umounted '/lxc_putold/sys' lxc-start 1383145786.577 DEBUG lxc_conf - umounted '/lxc_putold' lxc-start 1383145786.577 INFO lxc_conf - created new pts instance lxc-start 1383145786.578 DEBUG lxc_conf - drop capability 'sys_boot' (22) lxc-start 1383145786.578 DEBUG lxc_conf - capabilities have been setup lxc-start 1383145786.578 NOTICE lxc_conf - 'as1' is setup. lxc-start 1383145786.578 DEBUG lxc_cgroup - cgroup 'memory.limit_in_bytes' set to '20G' lxc-start 1383145786.578 DEBUG lxc_cgroup - cgroup 'cpuset.cpus' set to '12-23' lxc-start 1383145786.578 INFO lxc_cgroup - cgroup has been setup lxc-start 1383145786.578 INFO lxc_apparmor - setting up apparmor lxc-start 1383145786.578 INFO lxc_apparmor - changed apparmor profile to lxc-container-default lxc-start 1383145786.578 NOTICE lxc_start - exec'ing '/sbin/init' lxc-start 1383145786.578 INFO lxc_conf - looking at .15 20 0:14 / /sys rw,nosuid,nodev,noexec,relatime - sysfs sysfs rw . lxc-start 1383145786.578 INFO lxc_conf - now p is . /sys. lxc-start 1383145786.578 INFO lxc_conf - looking at .16 20 0:3 / /proc rw,nosuid,nodev,noexec,relatime - proc proc rw . lxc-start 1383145786.578 INFO lxc_conf - now p is . /proc. lxc-start 1383145786.578 INFO lxc_conf - looking at .17 20 0:5 / /dev rw,relatime - devtmpfs udev rw,size=32961632k,nr_inodes=8240408,mode=755 . lxc-start 1383145786.578 INFO lxc_conf - now p is . /dev. lxc-start 1383145786.578 INFO lxc_conf - looking at .18 17 0:11 / /dev/pts rw,nosuid,noexec,relatime - devpts devpts rw,mode=600,ptmxmode=000 . lxc-start 1383145786.578 INFO lxc_conf - now p is . /dev/pts. lxc-start 1383145786.578 INFO lxc_conf - looking at .19 20 0:15 / /run rw,nosuid,noexec,relatime - tmpfs tmpfs rw,size=6594456k,mode=755 . lxc-start 1383145786.578 INFO lxc_conf - now p is . /run. lxc-start 1383145786.578 INFO lxc_conf - looking at .20 1 252:0 / / rw,relatime - ext4 /dev/mapper/limitorderbook1-root rw,errors=remount-ro,data=ordered . lxc-start 1383145786.578 INFO lxc_conf - now p is . /. lxc-start 1383145786.578 INFO lxc_conf - looking at .22 15 0:16 / /sys/fs/cgroup rw,relatime - tmpfs none rw,size=4k,mode=755 . lxc-start 1383145786.578 INFO lxc_conf - now p is . /sys/fs/cgroup. lxc-start 1383145786.578 INFO lxc_conf - looking at .23 15 0:17 / /sys/fs/fuse/connections rw,relatime - fusectl none rw . lxc-start 1383145786.578 INFO lxc_conf - now p is . /sys/fs/fuse/connections. lxc-start 1383145786.578 INFO lxc_conf - looking at .24 15 0:6 / /sys/kernel/debug rw,relatime - debugfs none rw . lxc-start 1383145786.579 INFO lxc_conf - now p is . /sys/kernel/debug. lxc-start 1383145786.579 INFO lxc_conf - looking at .25 15 0:10 / /sys/kernel/security rw,relatime - securityfs none rw . lxc-start 1383145786.579 INFO lxc_conf - now p is . /sys/kernel/security. lxc-start 1383145786.579 INFO lxc_conf - looking at .26 19 0:18 / /run/lock rw,nosuid,nodev,noexec,relatime - tmpfs none rw,size=5120k . lxc-start 1383145786.579 INFO lxc_conf - now p is . /run/lock. lxc-start 1383145786.579 INFO lxc_conf - looking at .27 19 0:19 / /run/shm rw,nosuid,nodev,relatime - tmpfs none rw . lxc-start 1383145786.579 INFO lxc_conf - now p is . /run/shm. lxc-start 1383145786.579 INFO lxc_conf - looking at .28 22 0:20 / /sys/fs/cgroup/cpuset rw,relatime - cgroup cgroup rw,cpuset,clone_children . lxc-start 1383145786.579 INFO lxc_conf - now p is . /sys/fs/cgroup/cpuset. lxc-start 1383145786.579 INFO lxc_conf - looking at .29 19 0:21 / /run/user rw,nosuid,nodev,noexec,relatime - tmpfs none rw,size=102400k,mode=755 . lxc-start 1383145786.579 INFO lxc_conf - now p is . /run/user. lxc-start 1383145786.579 INFO lxc_conf - looking at .30 15 0:22 / /sys/fs/pstore rw,relatime - pstore none rw . lxc-start 1383145786.579 INFO lxc_conf - now p is . /sys/fs/pstore. lxc-start 1383145786.579 INFO lxc_conf - looking at .31 22 0:23 / /sys/fs/cgroup/cpu rw,relatime - cgroup cgroup rw,cpu . lxc-start 1383145786.579 INFO lxc_conf - now p is . /sys/fs/cgroup/cpu. lxc-start 1383145786.579 INFO lxc_conf - looking at .32 22 0:24 / /sys/fs/cgroup/cpuacct rw,relatime - cgroup cgroup rw,cpuacct . lxc-start 1383145786.579 INFO lxc_conf - now p is . /sys/fs/cgroup/cpuacct. lxc-start 1383145786.579 INFO lxc_conf - looking at .33 22 0:25 / /sys/fs/cgroup/memory rw,relatime - cgroup cgroup rw,memory . lxc-start 1383145786.579 INFO lxc_conf - now p is . /sys/fs/cgroup/memory. lxc-start 1383145786.579 INFO lxc_conf - looking at .34 22 0:26 / /sys/fs/cgroup/devices rw,relatime - cgroup cgroup rw,devices . lxc-start 1383145786.579 INFO lxc_conf - now p is . /sys/fs/cgroup/devices. lxc-start 1383145786.579 INFO lxc_conf - looking at .35 22 0:27 / /sys/fs/cgroup/freezer rw,relatime - cgroup cgroup rw,freezer . lxc-start 1383145786.579 INFO lxc_conf - now p is . /sys/fs/cgroup/freezer. lxc-start 1383145786.579 INFO lxc_conf - looking at .36 22 0:28 / /sys/fs/cgroup/blkio rw,relatime - cgroup cgroup rw,blkio . lxc-start 1383145786.579 INFO lxc_conf - now p is . /sys/fs/cgroup/blkio. lxc-start 1383145786.579 INFO lxc_conf - looking at .37 22 0:29 / /sys/fs/cgroup/perf_event rw,relatime - cgroup cgroup rw,perf_event . lxc-start 1383145786.579 INFO lxc_conf - now p is . /sys/fs/cgroup/perf_event. lxc-start 1383145786.579 INFO lxc_conf - looking at .38 22 0:30 / /sys/fs/cgroup/hugetlb rw,relatime - cgroup cgroup rw,hugetlb . lxc-start 1383145786.579 INFO lxc_conf - now p is . /sys/fs/cgroup/hugetlb. lxc-start 1383145786.579 INFO lxc_conf - looking at .39 20 9:2 / /data rw,relatime - ext4 /dev/md2 rw,errors=remount-ro,data=ordered . lxc-start 1383145786.579 INFO lxc_conf - now p is . /data. lxc-start 1383145786.579 INFO lxc_conf - looking at .40 20 8:1 / /boot rw,relatime - ext2 /dev/sda1 rw,errors=continue . lxc-start 1383145786.579 INFO lxc_conf - now p is . /boot. lxc-start 1383145786.579 INFO lxc_conf - looking at .41 22 0:31 / /sys/fs/cgroup/systemd rw,nosuid,nodev,noexec,relatime - cgroup systemd rw,name=systemd . lxc-start 1383145786.579 INFO lxc_conf - now p is . /sys/fs/cgroup/systemd. lxc-start 1383145786.579 NOTICE lxc_start - '/sbin/init' started with pid '6249' lxc-start 1383145786.579 WARN lxc_start - invalid pid for SIGCHLD <4>init: ureadahead main process (7) terminated with status 5 <4>init: console-font main process (94) terminated with status 1 And it will just sit there like that for hours at least. The container becomes pingable but I can't ssh and if I try lxc-console -n as1 I get a blank screen. If I do lxc-stop -n as1 or ^C in the window where it has hung I get: ^CTERM environment variable not set. <4>init: plymouth-upstart-bridge main process (192) terminated with status 1 <4>init: hwclock-save main process (187) terminated with status 70 * Asking all remaining processes to terminate... ...done. * All processes ended within 1 seconds... ...done. * Deactivating swap... ...fail! mount: cannot mount block device /dev/md2 read-only * Will now restart But after 20 minutes it hasn't restarted. Any ideas why these containers are hanging?

  Read the article

• SOLVED Install MythTV & 11.10 on Lenovo S12 (Intel atom) with wireless

  - by keepitsimpleengineer

  This is how I installed Ubuntu 11.10 and MythTV client on my Lenovo S12 (Intel Atom) laptop and use it using WiFi (see additional notes at end). I did this because the upgrade from 11.04 bricked the laptop. Note that the partitions on the Lenovo standard disk were already in place for this installation. Also note that my LAN is setup for fixed IP addresses. Downloaded and burned 11.10 x86 Desktop Ubuntu CD Connected the power supply cord, LAN wire and the external DVD USB drive. Ran Windows XP and made sure performance level "Performance" was set and "Wireless" was enabled. Booted S12 from CD Disabled Networking from icon on upper left panel icon Edited Connections… "Wired connection 1" ? Set IP address, accepted default netmask and set gateway. Also set DNS server. Good idea to check "Connection Information" here to verify everything's O.K. Selected Install Ubuntu from the initial "Install" window Verified the three items were checked (required disk space available, plugged into a power source, & connected to the Internet) Selected Download updates while installing and third party software. Hit Continue… At wireless selected don't want to connect…WiFi…now. Continue… At Installation type, selected Something else. Continue… At partition tale, selected the ext4 Linux partition, set the mount point as "/", and marked for formatting. Here I selected the main disk (/sda) for installing the boot manager. Continue… Selected or verified my Time zone. Continue… Selected my keyboard layout. Continue… Filled in the who are you fields. Make sure password is required to sign in is checked. Continue… Chose a picture. Continue… I selected import no accounts. Continue… Wait as the Install creeps along. If your screen goes blank, tap the space bar ? apparently the screen saver/power plan does this. There are several progress bars. The longest was "Installing system", and it was the next to the last one. Installation Complete window appears, Restart Now… Wait as it stops, The screen blanks then the message "…remove…media…close tray…press enter" I just unplugged the USB DVD and hit enter… It was disheartening but the screen turned Ubuntu Purple-beige and nothing happened, so I help down the power key until it shut down, the pressed it again and the Grub Boot screen appeared. Select Ubuntu… 25.The screen went blank with the little flashing underscore cursor on it and the disk light would occasionally flash. I hit the enter key and eventuality Ubuntu started. After a somewhat long time the unity desktop appeared. 11.10, unlike earlier versions, retains the connection information. Check this by checking the network icon on the upper left applet panel. Here the touch-pad·mouse quit working and I had to reboot. It takes and extremely long time to boot, sometimes requiring several power off/ power on (cold boot). You can try to get the default network manager to work, but it might not, it didn't on mine for WiFi. Thanks to: Chris at URL here's what to do… disconnect your wired Internet connection. input your wireless information into network manager open a terminal (unity dash, top of icon totem, open, and make sure the ruler&pen icon on the bottom is selected, 2nd from left) type in "terminal". Might be a good idea to drag and drop the terminal icon to the terminal, it's easy to get rid of later. click to open a terminal, and type in: sudo rmmod acer_wmi && echo "blacklist acer_wmi" >> /etc/modprobe.d/blacklist.conf and hit enter. type in your password as asked. if you have correctly entered your WiFi information and you are near your AP, you should connect immediately if not, see the URL above ? you might need to replace "network manager" with "wicd" ? I did with 11.04. Update the new 11.10, in the upper left panel applet weird·gear icon is menu with a line about updating. It's the new way to invoke Update Manager. Your lenovo S12 (intel atom) should now run the new unity Ubuntu. Point your elbow at the ceiling and pat yourself on the back. Installing Mythbuntu Client 24.1 Open mythbuntu.org/repos (I urge you not to directly use Ubuntu Software Center for this) Install Mythbuntu Repos Save the file (in ~/Downloads, the default) Run the file ? it will update your repositories so that you will get the proper installation sources ? it will start Ubuntu Software Center to do this ? Click Install… You will need your password. Debconf window will open, select by making sure check mark is in the little box "Would you like to activate…". Forward… Which version? At the time of writing the current "Stable" version was 24.1, select 0.24.x… Forward… Read the message, then forward… Delete the downloaded file. Install synaptic (unity dash, top of icon totem, open, and make sure the ruler&pen icon on the bottom is selected, 2nd from left) type in "synaptic". Click on the synaptic icon. Ubuntu Software Center will open and allow you to install synaptic package manager. Open Synaptic (unity dash, top of icon totem, open, and make sure the ruler&pen icon on the bottom is selected, 2nd from left) type in "Synaptic". Might be a good idea to drag and drop the terminal icon to the terminal, it's easy to get rid of later. Run synaptic, read the intro, and close the intro window. Type in mythbuntu-control-centre in the Quick filter text box, and then select it "Mark for installation" by clicking on the box next to it's name. Marvel at the additional to be installed items, then select "?Mark"… At the top of the synaptic window click on the "? Apply" button. Marvel at the amount of stuff to be installed, the click on "Apply". When finished, close finished window and synaptic. Open mythbuntu-control-centre (unity dash, top of icon totem, open, and make sure the ruler&pen icon on the bottom is selected, 2nd from left) type in "mythbuntu". Might be a good idea to drag and drop the mythbuntu-control-centre icon to the terminal, it's easy to get rid of later. You can now configure and install the frontend. Go down the icon totem on the right side of the window and click as needed… System roles. ? No Backend, Desktop Frontend, and Ubuntu Desktop. Apply… & Apply changes… & Password… MySQL Configuration ? from backend ? Setup General Alt-N(ext) Alt-N(ext) Stetting Access Setup PIN code: ~~~~ Input Security key and click "Test Connection", if ?, then Apply… & Apply… {note: for some inexplicable reason, control centre hung on this, but when I restarted it, it was set properly} Graphics drivers, When I did this, only the Broadcom wireless driver showed up. I closed without doing anything. Services. I enabled SSH & Samba. Apply… & Apply… Repositories. Asked & Answered. MythExport. Pass, I believe it requires backend on the same system. Proprietary Codec Support. Check to enable, Apply… & Apply… System Updates. No action necessary, will be a part of the Ubuntu update mechanism. Themes and Artwork. For themes, I selected Enable/Update all. Apply… & Apply… Infrared & Startup behavior and Plugins. Defer until you know more. Close software centre. Open mythTV (unity dash, top of icon totem, open, and make sure the ruler&pen icon on the bottom is selected, 2nd from left) type in "mythTV". Might be a good idea to drag and drop the mythTV icon to the terminal, it's easy to get rid of later. Incorrect Group Membership. Fix this by clicking "Yes"… Log out/end. Do this by clicking "Yes"… For my Lenovo S12, I had to manually restart Ubuntu - and still with the very long restart…/no start/cold boot/reboot/pressing the shift key required Open mythTV (unity dash, top of icon totem, open, and make sure the ruler&pen icon on the bottom is selected, 2nd from left) type in "mythTV". Might be a good idea to drag and drop the mythTV icon to the terminal, it's easy to get rid of later. Will open with Select country & language. Do so. then get message with "No", hit "Ok" and arrive at the data base Configuration 1/2 screen. You will need your brackend password, from backend ? Setup General Database Configuration 1/2 Password:~? Enter this Hit Alt-n to go to the next page. Select "Use custom id…", then enter a custom ID, I use the machine's name. Hit finish, and MythTV should start up with all default settings. For the lenovo S12, the first thing you want to do is to set Playback profiles to "Normal". From Setup TV Settings Playback Alt-N(ext) Alt-N(ext) Playback Profiles (3/8) : Change Current Video Playback Profile to "Normal". You can fiddle with this setting later. For the lenovo S12, the second thing is to get the sound going. From Setup General Alt-N(ext) Alt-N(ext) Alt-N(ext) Audio System: The top of the screen is a button title "Scan for audio devices", move the highlight there and press the Space bar. Then Tab down to Audio Output Device: and left-right arrow until "ALSA:hw:Card=Intel,DEV=0" is selected. Then Alt-N(ext) until "Finish". Now you should have sound. You should now have MythTV working nicely on the Lenovo S12 Notes about wireless: Running Lenovo S12 on wireless is demanding on both power and WiFi connection. Best results will be obtained when running on power and wired connection. I run my S12 on wireless, actually two serial connections with two access points, something that is not easy to achieve. Here Mythbuntu client-server (in den) <? wireless link 1 <?office LAN? wireless link 2 <? Lenovo S12 Ubuntu 11.10 The office LAN is fixed IP behind an Untangle firewall router. There is another MythTV client on Ubuntu 10.10 computer in the office (which has always worked well). ProblemMythbuntu\Win7 client hangs with frozen frames, short segment of audio repeating. Hardware Rosewill RNX-G300EX IEEE 802.11b/g PCI Wireless Card on client-server 2 Linksys WRT54GL wireless broadband routers on LAN for link1 and link 2 WRT54GL FirmwareDD-WRT v24-sp2(07/22/09) voip set up to act as an access point. Note? many people advised this was an unworkable scheme, and in probably most cases it will be. Solution? Set up DD-WRT with the following Wireless settings… Basic Channel: Different fixed channels at least 4 difference, I use 6 & 11 Basic Sensitivity Range (ACK timing): 50 MAC filter use filter: Enable, Selected Permit only clients listed to access… Requires adding MAC addresses in "Edit MAC Filter List" This causes the 54GL's to ignore any but the listed MAC address, down side, no "guest" capability. Advanced Basic rate: All Advanced CTS Protection Mode: Off Advanced Frame Burst: Enable Advanced Max associate clients: 4 for client link 2, 1 for client-server link 1 Advanced AP isolation: Enable Advanced Preamble: Short Advanced Afterburner: On Advanced Wireless GUI access: Off Advanced WMM support: Off Other settings: default for supplied firmware. Why I suspect this worked? The 54GL Access Points's with the firmware's setting are set to handle a multiple client, wide area situation. With these mods I reconfigured them for a small area, few client situation, disabling Advanced WMM probably the most important. In addition, the client mythtv when used all other users of its access point are turned off except for a Skype phone. Also, the client-server is set up to allow other connections though it's LAN connection, and these are used to connect the TV and disc players, not used when client is being used.

  Read the article

< Previous Page | 235 236 237 238 239 240 241 242 243 244 245 246  | Next Page >