Search Results

Search found 7776 results on 312 pages for 'configure'.

Page 242/312 | < Previous Page | 238 239 240 241 242 243 244 245 246 247 248 249  | Next Page >

• Ubuntu second static IP, ifconfig, /etc/network/interfaces

  - by Schmoove

  I would like to add a second static IP to my local Ubuntu 11.10 desktop machine and have it automatically available after rebooting. So far I am successfully using ifconfig to to temporarily set up an alias for my primary network interface: # ifconfig eth1:0 192.168.178.3 up # ifconfig eth1 Link encap:Ethernet HWaddr c8:60:00:ef:a3:d9 inet addr:192.168.178.2 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::ca60:ff:feef:a3d9/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:61929 errors:0 dropped:0 overruns:0 frame:0 TX packets:64034 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:45330863 (45.3 MB) TX bytes:28175192 (28.1 MB) Interrupt:42 Base address:0x4000 eth1:0 Link encap:Ethernet HWaddr c8:60:00:ef:a3:d9 inet addr:192.168.178.3 Bcast:192.168.178.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:42 Base address:0x4000 However, when I add the following to /etc/network/interfaces, the alias is not up and running as expected after a reboot: # vi /etc/network/interfaces auto eth1:0 iface eth1:0 inet static address 192.168.178.3 netmask 255.255.255.0 I would like to know what to configure to get this to work. As a side note, I am running gnome shell.

  Read the article

• Tri-head linux system with Xmonad: is it possible to have HW acceleration

  - by progo

  What means there exists to have three monitors, all controlled by Xmonad and have hardware 3D acceleration as well? I had the pleasure of using three monitors earlier this year, and while Xmonad and Xinerama handle three monitors easily, I had to throw in an extra display driver, and also let go of Nvidia's own TwinView (which is a hack on Xinerama). This left me with no HW acceleration and some flickering as double buffering wouldn't work with certain applications. However, the three monitors handle so beautifully that I had hard time coming back to two. I understand the easiest way to achieve HW-accelerated tri-head combo is to split into two Xorgs. I wouldn't be able to switch windows between the Xorgs, so I'm not really into this solution. What's more, having a cheap and old PCI card along with even slightly better PCIe seemed to slow things down. Even if I occasionally disabled the third monitor from Xorg configure, I couldn't get HW acceleration to work. Only after I physically disconnected the old PCI card, I could get the games back in business. Would a Matrox Dual/Tri-head2go and a powerful Nvidia GPU do the trick? I understand Xmonad can be configured to "believe" that a "single" (as Dualhead2Go will merge) 3360x1050 display is actually two different ones? So that Xmonad's Mod-w and Mod-e would work properly there.

  Read the article

• How do I hook into Tar with BASH?

  - by orb

  Long Story Short I am working with Tar archives that contain PNG images in base64 encoding. I would like to use BASH (or whatever else works) to hook into the extraction function of Tar to decode PNG images from base64 encoding to standard PNG encoding after the files are unpacked. A simple cat $input-file | base64 -d >$output-file will successfully decode the images. Is there a way I can hook into tar -xf so that users do not have to do any (or minimal) extra work to decode the images? In the GNU Tar documentation (http://www.gnu.org/software/tar/manual/html_chapter/Backups.html#SEC97) I found that there are in fact variables reserved to hold the names of functions I desire to be hooked into various moments in Tar program execution. However, the documentation explains that these variables, along with other variables that can be set to configure Tar, are located in a file named backup-specs. Unfortunately, the path to this file is not given. Further, running sudo find / -name backup-specs tells me that this file is not present on my Ubuntu version 13.04 system. Background Information not included in the Long Story Short I have been working on a browser-based (WebGL) particle effect creation application (http://www.particleeffect.org), (https://github.com/cgrabowski/webgl-particle-effect-editor), (https://github.com/cgrabowski/webgl-particle-effect). I have began to write a client-side-only solution for saving and loading effect data as a tar archive. However, since client-side JavaScript has limited capability to process binary data, the images used as textures in the effect are saved with base64 encoding. I have been able to implement saving effect data as a Tar archive (haven't pushed that to Github yet). However, the images present in said Tar archive cannot be manipulated unless they are decoded from base64 encoding.

  Read the article

• MOSS2007 tries to use ActiveDirectory when I have configured an alternative membership provider

  - by glenatron

  I've got a MOSS site that I am trying to configure using Forms authentication and absolutely any kind of membership provider whatsoever. Thus far ActiveDirectory has proved obstructively difficult so I've just whipped up a simple stub membership provider and put it in the GAC. It's a very basic and simple provider but it works fine with an ASP.Net site, I just can't make it work with Sharepoint. On Sharepoint I get the following error when I look for StubProvider:Bob ( or anything else for that matter) from the "Policy For Web Application" people picker: Error in searching user 'StubProvider:bob' : System.ComponentModel.Win32Exception: Unable to contact the global catalog server at Microsoft.SharePoint.Utilities.SPActiveDirectoryDomain.GetDirectorySearcher() at Microsoft.SharePoint.WebControls.PeopleEditor.SearchFromGC(SPActiveDirectoryDomain domain, String strFilter, String[] rgstrProp, Int32 nTimeout, Int32 nSizeLimit, SPUserCollection spUsers, ArrayList& rgResults) at Microsoft.SharePoint.Utilities.SPUserUtility.SearchAgainstAD(String input, SPActiveDirectoryDomain domainController, SPPrincipalType scopes, SPUserCollection usersContainer, Int32 maxCount, String customQuery, TimeSpan searchTimeout, Boolean& reachMaxCount) at Microsoft.SharePoint.Utilities.SPActiveDirectoryPrincipalResolver.SearchPrincipals(String input, SPPrincipalType scopes, SPPrincipalSource sources, SPUserCollection usersContainer, Int32 maxCount, Boolean& reachMaxCount) at Microsoft.SharePoint.Utilities.SPUtility.SearchPrincipalFromResolvers(List`1 resolvers, String input, SPPrincipalType scopes, SPPrincipalSource sources, SPUserCollection usersContainer, Int32 maxCount, Boolean& reachMaxCount, Dictionary`2 usersDict). The Provider is named as Authentication Provider for the Site Collection in question. As far as I can tell this is because Sharepoint is still trying to access ActiveDirectory rather than talking to the provider I'm asking it to use. My Sharepoint Central Administration section includes this: <membership> <providers> <add name="StubProvider" type="StubMembershipProvider.Provider, StubMembershipProvider, Version=1.0.0.0, Culture=neutral, PublicKeyToken=5bd7e2498c3e1a03" /> </providers> </membership> And also: <PeoplePickerWildcards> <clear /> <add key="StubProvider" value="%" /> </PeoplePickerWildcards> Is there a clear reason why this would not be accessible from the PeoplePicker or why it is still trying to use ActiveDirectory? I've made sure I reset IIS and even restarted the server to see if either of those helped but they made no difference.

  Read the article

• Managing Linux Directory Permissions & SFTP

  - by Dizzle

  Good morning; I have a RHEL 5.7 web server configured to allow SSH/SFTP only by specific groups. I'd like for content managers to upload content to their respective directories and have that content inherit the user/group ownership of the directory regardless of upload method or application. For example: John is in group "web" for SSH/SFTP rights and "finance" for directory permissions, and uploads to directory "webstuff" via SFTP. Directory "webstuff" has permissions of "2760" (rwxrws---), and ownership of "apache:finance". If John uploads an update to an existing file in "webstuff", the ownership of the file stays at "apache:finance". If John uploads a new file to "webstuff", the ownership of the file is "john:finance". My desire is to have any file from John uploaded to "webstuff" to change to the directory's owner. I've tried with setuid and setgid both set, but the user-ownership didn't take. I've seen mentions on ServerFault of using ACL's, or a chrooted jail for SFTP but I have yet to configure and test them, and I don't know if they're a viable solution (they could be, I just don't know because I've never done either). Any thoughts and assistance would be greatly appreciated.

  Read the article

• pppd disconnects from 3G, doesn't reconnect, w/ persist set

  - by bytenik

  I am trying to configure pppd to connect to a 3G network (Sprint, in this case) and then stay connected, reconnecting automatically if the remote connection is terminated. I have enabled the persist option. My configuration file is as follows: hide-password noauth connect "/usr/sbin/chat -v -f /etc/chatscripts/cellular" debug /dev/cell 921600 defaultroute noipdefault user " " persist maxfail 0 lcp-echo-failure 10 lcp-echo-interval 60 holdoff 5 However, when the peer disconnects the connection, pppd often waits a long time (substantially more than my holdoff) to reconnect the modem -- if it ever reconnects at all! An example log showing this: May 23 05:17:24 00270e0a8888 pppd[2408]: rcvd [LCP TermReq id=0x26] May 23 05:17:24 00270e0a8888 pppd[2408]: LCP terminated by peer May 23 05:17:24 00270e0a8888 pppd[2408]: Connect time 60.1 minutes. May 23 05:17:24 00270e0a8888 pppd[2408]: Sent 0 bytes, received 0 bytes. May 23 05:17:24 00270e0a8888 pppd[2408]: Script /etc/ppp/ip-down started (pid 2456) May 23 05:17:24 00270e0a8888 pppd[2408]: sent [LCP TermAck id=0x26] May 23 05:17:24 00270e0a8888 pppd[2408]: Script /etc/ppp/ip-down finished (pid 2456), status = 0x0 May 23 05:17:24 00270e0a8888 pppd[2408]: Hangup (SIGHUP) May 23 05:17:24 00270e0a8888 pppd[2408]: Modem hangup May 23 05:17:24 00270e0a8888 pppd[2408]: Connection terminated. May 23 05:17:24 00270e0a8888 pppd[2408]: Terminating on signal 15 May 23 05:17:24 00270e0a8888 pppd[2408]: Exit. May 23 06:08:07 00270e0a8888 pppd[2500]: pppd 2.4.5 started by root, uid 0 May 23 06:08:10 00270e0a8888 pppd[2500]: Script /usr/sbin/chat -v -f /etc/chatscripts/cellular finished (pid 2530), status = 0x0 May 23 06:08:10 00270e0a8888 pppd[2500]: Serial connection established. May 23 06:08:10 00270e0a8888 pppd[2500]: using channel 11 The disconnect at the request of the peer occurs at 5:17, but the reconnect didn't happen until 6:08. I had a friend monitoring the server so I'm not certain that this wasn't a manual reconnection. Either way, it either took almost an hour to reconnect or never reconnected. Shouldn't persist + holdoff 5 cause this to automatically reconnect after 5 seconds of the link terminating?

  Read the article

• RRAS with DHCP when the IP pool is on a different subnet

  - by John B

  I run a small business network and the last couple of days I have been setting up some equipment to add VPN capabilities to our network. I've got the following set up: Windows 2008 R2 with RRAS - 172.22.200.50 Cisco RV082 router - 172.22.100.1 / 172.22.200.1 The Cisco router only support DHCP on a single class C network; 172.22.100.0/24. On the Cisco router I have set up an additional subnet; 172.22.200.0/24. The DHCP range is 172.22.100.200-254 When a PPTP connection comes in to the router, it is forwarded to my RRAS at 172.22.200.50. If I configure RRAS to assign IPs from a static pool on the 172.22.200.0/24 subnet everything works fine except the DNS suffix / search domain. However, if I set RRAS to use DHCP I am no longer able to contact any devices on the network. The IP I receive is on a different subnet (172.22.100.0/24). Is it possible to still use DHCP as the method of ip assignment in RRAS, even when the IP adresses assigned are in a different subnet? If yes, what piece of configuration am I missing to fix the VPN connection issues mentioned in the paragraph above. The reason I want RRAS with DHCP to work is because from what I have understood, this is the "only" way to hand out a DNS suffix to VPN clients. Any help on this matter is greatly appreciated!

  Read the article

• Maximum limit of filepointer in php reached and not changeable

  - by mlaug

  I have a server with the current 5.3.x version installed. Since we are running a really simple and small server in php using sockets, that connects to a lot clients using sockets we need to raise the open file limit that has been already done on the server for the user, that runs the server #ulimit -a core file size (blocks, -c) 0 data seg size (kbytes, -d) unlimited scheduling priority (-e) 0 file size (blocks, -f) unlimited pending signals (-i) 29879 max locked memory (kbytes, -l) 64 max memory size (kbytes, -m) unlimited open files (-n) 8192 pipe size (512 bytes, -p) 8 POSIX message queues (bytes, -q) 819200 real-time priority (-r) 0 stack size (kbytes, -s) 8192 cpu time (seconds, -t) unlimited max user processes (-u) 29879 virtual memory (kbytes, -v) unlimited file locks (-x) unlimited and we compiled php with --enable-fd-setsize=8192 still we are getting [19-Nov-2012 09:24:23 Europe/Berlin] PHP Warning: socket_select(): You MUST recompile PHP with a larger value of FD_SETSIZE. It is set to 1024, but you have descriptors numbered at least as high as 1024. --enable-fd-setsize=2048 is recommended, but you may want to set it to equal the maximum number of open files supported by your system, in order to avoid seeing this error again at a later date. once in a while in our logs. Anyone knows who to configure the unix server and php correctly to have that working? I found a bug, but that is related to 2006 and marked as "not a bug" https://bugs.php.net/bug.php?id=37025&edit=1

  Read the article

• Windows Media Center doesn't see my movies

  - by DrJekyll

  I am trying to configure my Windows Media Center (Windows 7 Ultimate). I selected folder with my movies and added it to the library, but when I went to the movies library, it says "There are no items in this library yet - Windows Media Center is searching for media files in the background...". I have all necessary codecs installed, Windows Media Player opens those movies correctly. When I right click on the file - Open with - Windows Media Center it also plays them without any problem. Any ideas why they don't appear in the libraries? Edit: Movies are coded with divx and xvid codecs and they have ".avi" extension. Windows doesn't have problems playing them. I told Media Center where the files are. I even pointed Windows Media Center to a folder with only one .avi file it still couldn't find anything there. (I have given it quiet some time, even though searching in the directory with only one file shouldn't take more than a few seconds.) When I add a folder with a lot of movies, I get a dialog box "You can wait while media is added or select OK to continue using Windows Media Center.".                                                                        At the end it says it added about 90 movies, but when I go to the libraries, it's still empty.

  Read the article

• Ways to have audio output without wires

  - by viraptor

  I'm trying to find a way of using my home speakers/amp without actually having to connect them. There are two laptops that use them normally (so I don't like changing the connection all the time) and I'd rather move the speakers to a place that's away from the couch. I'm not sure how to do this though... The options I can think of are: some kind of wireless jack-jack connection finally getting a media server Unfortunately I can't find any good product for the first solution. I've seen some headphones which have the receiver integrated and a separate transmitted, so in general the idea is already out there, just not the way I need ;) I've seen also http://www.miccus.com/products/blubridge-mini-jack, but I'd have to have a compatible receiver which I can't find on its own (maybe there's some application that the media server could use?). As far as media server goes... many of the plug servers look really interesting, but I'm not sure how to create an audio output and how to redirect the input really. None of the plug servers I've seen so far advertises the option of audio output jack port. I think this part could be fixed by getting one with an usb port and a separate cheap usb soundcard. I hope that input can be sorted out in some rather simple way. I've got Linux running on both laptops so I hope that would be possible to configure jack/pulse/whatever to use the remote endpoint, or even write a simple local-/dev/dsp:network:media-server-/dev/dsp forwarder. So the main question is... are there better ways? Are there any out of the box solutions? Or maybe this was already done by someone and described somewhere?

  Read the article

• Why is it necessary to chmod o+r parent directory to fix 403 access forbidden error with Nginx and P

  - by davenolan

  This may be an Nginx wrinkle, or it may be because I don't understand Unix permissions. We're using Hudson CI to deploy our staging instance. So RAILS_ROOT is /var/lib/hudson/jobs/JOBNAME/workspace. Hudson runs as hudson user Nginx runs as www-data user hudson and nginx are both members of the www group root of my nginx conf points to RAILS_ROOT/public as per normal. RAILS_ROOT/config/environment.rb is owned by www-data (so Passenger runs as www-data) RAILS_ROOT and everything in it is owned by the www group and group has r/w/x permissions As it stood, Nginx threw 403 permission denied when requesting any url. error.log contained entries like this: public/index.html" is forbidden (13: Permission denied). These did not fix the or change the error (each with a stop/start of Ngnix): chmod 777 -R RAILS_ROOT chgrp www -R /var/lib/hudson I also tried Nginx as root, and passenger complained that it could not find config/environment (despite the path displayed on the error page being correct). The fix was to ensure everybody has read permissions on each directory in the heirachy. In this case chmod o+r /var/lib/hudson. But if the group has read permissions on the directory, and nginx is a member of the owner group of the directory, why was it necessary to allow everyone read permissions? Is there something have not grokked about permissions? $nginx -V nginx version: nginx/0.7.61 built by gcc 4.4.1 (Ubuntu 4.4.1-4ubuntu8) configure arguments: --prefix=/opt/nginx --add-module=/usr/lib/ruby/gems/1.8/gems/passenger-2.2.5/ext/nginx --with-http_ssl_module --with-pcre=~/src/pcre-8.00/ --with-http_stub_status_module $cat /etc/lsb-release DISTRIB_ID=Ubuntu DISTRIB_RELEASE=9.10 DISTRIB_CODENAME=karmic DISTRIB_DESCRIPTION="Ubuntu 9.10"

  Read the article

• Port forwarding + shared connection with Ubuntu

  - by Joey Adams

  Because my wireless router's ethernet ports are defective, I set up a shared wireless connection from my laptop (which has wifi) to my eMac (which does not) via a crossover ethernet cable. The laptop is behind a router as 192.168.1.131, and the eMac is behind the laptop as 10.42.43.1 . The laptop is running Ubuntu 9.10 (Karmic). I achieved the shared connection through NetworkManager Applet. I right-clicked on the network icon at the topright, went to Edit Connections, selected the Wired connection named "Auto eth0", clicked "Edit...", went to the "IPv4 Settings" tab, and selected the Method "Shared to other computers". The eMac can now access the Internet. Now I want to enable port forwarding. There's a game I want to play that needs port 6112 forwarded (both TCP and UDP) in order to host games. I set up the router to enable port forwarding for 192.168.1.131 (the laptop), but port forwarding still isn't available on the eMac. I suppose I need to pretend my laptop is a router and configure port forwarding on it, indicating that incoming connections to the laptop (192.168.1.131) should be forwarded to the eMac on the shared connection (10.42.43.1 ). Thus, packets coming into the router on port 6112 would be redirected to the laptop (by the router), then to the eMac (by the laptop). My question is, how would I do that on Ubuntu (in light of NetworkManager's presence)? Also, if I can't get this to work, does anyone mind hosting a comp stomp? :D

  Read the article

• Inconsistent SMTP Access

  - by Mike Hanson

  I have a mail server setup on Windows Server 2008. All was working fine, until I wanted to map a drive on the server so that I can access files on another machine. Windows prompted me to configure Network Discovery, which I did with the "Home/Office" option rather than "Public". After that, several access points that worked before stopped working, like VNC, SMTP, etc. After reinstalling those packages, things appeared to be working again. Unfortunately, problems have returned with my SMTP server. I can use an web-based SMTP tester, and it connects in 62msec (as expected). However, if I telnet from my machine on the same LAN, it takes more than 20 seconds to connect! When I try to send messages from Outlook, it times out entirely with the message: Sending' reported error (0x80042109) : 'Outlook cannot connect to your outgoing (SMTP) e-mail server. If you continue to receive this message, contact your server administrator or Internet service provider (ISP).' I've checked the firewall settings, I've tried configuring it to use port 587 instead of 25, but nothing gets around this problem. Does any have any useful insights? Thanks in advance!

  Read the article

• Adding third disk as a single disk in a server with an existing RAID1

  - by slowhandsolo

  I've got a ProLiant DL360 G5 server (Fedora 13) with two SAS disks in a hardware RAID 1, working fine. Now I hot plugged another SAS disk. I'd like to configure this new hard disk out of my RAID, as a single non-RAID disk (ex. /dev/sdb). Even after rebooting the server, I can't see the new disk with "fdisk -l". It displays only my hardware RAID, but not the new disk. [root@myserver]# fdisk -l Disco /dev/cciss/c0d0: 300.0 GB, 299966445568 bytes Disposit. Inicio Comienzo Fin Bloques Id Sistema /dev/cciss/c0d0p1 * 1 126 512000 83 Linux /dev/cciss/c0d0p2 126 71798 292422656 8e Linux LVM Disco /dev/dm-0: 234.9 GB, 234881024000 bytes Disco /dev/dm-1: 10.5 GB, 10536091648 bytes Disco /dev/dm-2: 21.0 GB, 20971520000 bytes Disco /dev/dm-3: 31.5 GB, 31474057216 bytes Disco /dev/dm-4: 1577 MB, 1577058304 bytes However, I can see the new disk using the HP Array Configuration Utility CLI for Linux "hpacucli": [root@myserver]# hpacucli => controller slot=0 physicaldrive all show status physicaldrive 1I:1:1 (port 1I:box 1:bay 1, 300 GB): OK physicaldrive 1I:1:2 (port 1I:box 1:bay 2, 300 GB): OK physicaldrive 1I:1:3 (port 1I:box 1:bay 3, 300 GB): OK => controller slot=0 pd all show detail Smart Array P400i in Slot 0 (Embedded) array A physicaldrive 1I:1:1 Port: 1I Box: 1 Bay: 1 physicaldrive 1I:1:2 Port: 1I Box: 1 Bay: 2 **unassigned** physicaldrive 1I:1:3 Port: 1I Box: 1 Bay: 3 Status: OK Drive Type: **Unassigned Drive** As you can see, I've got two SAS disks in a RAID 1 and the new disk as "unassigned". Is there any way to work with the new disk as another non-RAID single disk? If relevant, I want to create a new partition in my new disk, format it with mkfs and mount it, but as I can't see it with fdisk, I don't know how to do it. Thanks!

  Read the article

• Getting 401 when using client certificate with IIS 7.5

  - by Jacob

  I'm trying to configure a web site hosted under IIS 7.5 so that requests to a specific location require client certificate authentication. With my current setup, I still get a "401 - Unauthorized: Access is denied due to invalid credentials" when accessing the location with my client cert. Here's the web.config fragment that sets things up: <location path="MyWebService.asmx"> <system.webServer> <security> <access sslFlags="Ssl, SslNegotiateCert"/> <authentication> <windowsAuthentication enabled="false"/> <anonymousAuthentication enabled="false"/> <digestAuthentication enabled="false"/> <basicAuthentication enabled="false"/> <iisClientCertificateMappingAuthentication enabled="true" oneToOneCertificateMappingsEnabled="true"> <oneToOneMappings> <add enabled="true" certificate="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"/> </oneToOneMappings> </iisClientCertificateMappingAuthentication> </authentication> </security> </system.webServer> </location> The client certificate I'm using in my web browser matches what I've placed in the web.config. What am I doing wrong here?

  Read the article

• Overriding some DNS entries in BIND for internal networks

  - by Remy Blank

  I have an internal network with a DNS server running BIND, connected to the internet through a single gateway. My domain "example.com" is managed by an external DNS provider. Some of the entries in that domain, say "host1.example.com" and "host2.example.com", as well as the top-level entry "example.com", point to the public IP address of the gateway. I would like hosts located on the internal network to resolve "host1.example.com", "host2.example.com" and "example.com" to internal IP addresses instead of that of the gateway. Other hosts like "otherhost.example.com" should still be resolved by the external DNS provider. I have succeeded in doing that for the host1 and host2 entries, by defining two single-entry zones in BIND for "host1.example.com" and "host2.example.com". However, if I add a zone for "example.com", all queries for that domain are resolved by my local DNS server, and e.g. querying "otherhost.example.com" results in an error. Is it possible to configure BIND to override only some entries of a domain, and to resolve the rest recursively?

  Read the article

• Can't connect to MySQL on CentOS 5 Error 13 - Permission Denied

  - by abszero

  Ok, I have an install of CentOS 5 running as a GuestOS in VirtualBox. The network card for the Cent box is bridged with that of my host OS so that the boxes can see each other. Cent has an IP of 192.168.1.108 and my Host box has an IP of .104. Everything, with regard to networking, seems to be working properly as I can access the Drupal install that is on the Cent box from a web browser on my host box by navigating to http://192.168.1.108 however when I try to configure the database for Drupal through the Drupal install interface I am getting the Can't connect to MySQL error. First I thought this might of been a Firewall issue so I stopped iptables but that had no effect. I thought maybe the user I had setup did not have access to the server so I tried root and that did not work. Searching on the net said that I needed to provide a bind-address parameter to my.cnf so I did that with no change. (As a side note the length of my my.cnf file was MUCH shorter than the ones presented online. In fact under mysqld all I have are datadir, socket, user, and bind-address. Is this normal or should the file be more verbose?) After a few hours of messing with permissions and such I tried using 'localhost' as the value for the database server, from my HOST OS, and the Drupal install kicked off without a problem. So while my issue is resolved I am curious as to why 'localhost' works and why 192.168.1.108 did not? Is there something i need to do to specifically access the MySQL box via the aforementioned IP? Thanks.

  Read the article

• How to route public static IP to a virtual machine on a vmware ESXi host?

  - by Kevin Southworth

  I have 5 static IPs from my ISP (Comcast) and I have a physical machine with VMware ESXi 4.0 on it that is hosting multiple virtual machines. Right now I am just using the default vmware virtual network (vswitch0) with DHCP from the Comcast IP Gateway Router and everything is working fine. Each virtual machine can access the internet, etc. One of my virtual machines is a webserver (Windows Server 2008) and I want to assign it to 1 of my 5 static IPs so it's accessible from the public internet, while leaving the other VMs on the internal LAN still using DHCP. If I just plug my laptop directly into the Comcast IP Gateway (it has 4 ports on the back) and assign my laptop a Static IP using the windows networking dialogs, then I can hit my laptop from the public internet and it works great. However, if I try to do the same steps to set a static IP config on my Windows Server 2008 VM, it does not work. The VM cannot access the internet (open Firefox and try to visit google.com), and I cannnot see the VM from the public internet either. I'm assuming I'm missing something in the ESXi config somewhere, but I'm pretty new to ESXi and I'm not sure how to configure it to work this way.

  Read the article

• Corrupt install of Ruby?

  - by wilhelmtell

  I'm having issues requiring 'digest/sha1'. ~$ ./configure --prefix=$HOME/usr --program-suffix=19 --enable-shared ~$ make ~$ make install ~$ irb19 irb(main):001:0> require 'digest/sha1' LoadError: dlopen(/Users/matan/usr/lib/ruby19/1.9.1/i386-darwin9.8.0/digest/sha1.bundle, 9): Symbol not found: _rb_Digest_SHA1_Finish Referenced from: /Users/matan/usr/lib/ruby19/1.9.1/i386-darwin9.8.0/digest/sha1.bundle Expected in: flat namespace - /Users/matan/usr/lib/ruby19/1.9.1/i386-darwin9.8.0/digest/sha1.bundle from (irb):1:in `require' from (irb):1 from /Users/matan/usr/bin/irb19:12:in `<main>' irb(main):002:0> I know some standard modules require fine, while others don't. If i'd say require 'digest' then that works fine. Just a couple of days ago I uninstalled Ruby and re-installed it. When I first installed Ruby I installed it in a similar manner, from source prefixed at my local $HOME/usr directory. I tried removing each and every file make install installs, then re-installing, but that didn't help. Do you have an idea what the issue is and how to resolve it?

  Read the article

• tail -f and then exit on matching string

  - by Patrick

  I am trying to configure a startup script which will startup tomcat, monitor the catalina.out for the string "Server startup", and then run another process. I have been trying various combinations of tail -f with grep and awk, but haven't got anything working yet. The main issue I am having seems to be with forcing the tail to die after grep or awk have matched the string. I have simplified to the following test case. test.sh is listed below: #!/bin/sh rm -f child.out ./child.sh > child.out & tail -f child.out | grep -q B child.sh is listed below: #!/bin/sh echo A sleep 20 echo B echo C sleep 40 echo D The behavior I am seeing is that grep exits after 20 seconds , however the tail will take a further 40 seconds to die. I understand why this is happening - tail will only notice that the pipe is gone when it writes to it which only happens when data gets appended to the file. This is compounded by the fact that tail is to be buffering the data and outputting the B and C characters as a single write (I confirmed this by strace). I have attempted to fix that with solutions I found elsewhere, such as using unbuffer command, but that didn't help. Anybody got any ideas for how to get this working how I expect it? Or ideas for waiting for successful Tomcat start (thinking about waiting for a TCP port to know it has started, but suspect that will become more complex that what I am trying to do now). I have managed to get it working with awk doing a "killall tail" on match, but I am not happy with that solution. Note I am trying to get this to work on RHEL4.

  Read the article

• Linux authentication via ADS -- allowing only specific groups in PAM

  - by Kenaniah

  I'm taking the samba / winbind / PAM route to authenticate users on our linux servers from our Active Directory domain. Everything works, but I want to limit what AD groups are allowed to authenticate. Winbind / PAM currently allows any enabled user account in the active directory, and pam_winbind.so doesn't seem to heed the require_membership_of=MYDOMAIN\\mygroup parameter. Doesn't matter if I set it in the /etc/pam.d/system-auth or /etc/security/pam_winbind.conf files. How can I force winbind to honor the require_membership_of setting? Using CentOS 5.5 with up-to-date packages. Update: turns out that PAM always allows root to pass through auth, by virtue of the fact that it's root. So as long as the account exists, root will pass auth. Any other account is subjected to the auth constraints. Update 2: require_membership_of seems to be working, except for when the requesting user has the root uid. In that case, the login succeeds regardless of the require_membership_of setting. This is not an issue for any other account. How can I configure PAM to force the require_membership_of check even when the current user is root? Current PAM config is below: auth sufficient pam_winbind.so auth sufficient pam_unix.so nullok try_first_pass auth requisite pam_succeed_if.so uid >= 500 quiet auth required pam_deny.so account sufficient pam_winbind.so account sufficient pam_localuser.so account required pam_unix.so broken_shadow password ..... (excluded for brevity) session required pam_winbind.so session required pam_mkhomedir.so skel=/etc/skel umask=0077 session required pam_limits.so session required pam_unix.so require_memebership_of is currently set in the /etc/security/pam_winbind.conf file, and is working (except for the root case outlined above).

  Read the article

• Simple Linux program that takes any HTTP/HTTPS request and returns a single page?

  - by ultrasawblade

  I have a Linux box operating as router. There's a NIC that's connected to the internet (WAN), a NIC connected to an 8-port GbE switch (LAN), and a NIC connected to a Linksys wireless N-router (WLAN). Routing between everything is working perfectly. I have security completely disabled on the wireless router, but the WLAN NIC is firewalled such that it will only accept DNS queries and PPTP VPN connections. Currently HTTP/HTTPS traffic and everything else is blocked. I would like to run something that listens on port 80/443 of the WLAN NIC, and, for non VPN'ed connections, given any HTTP/HTTPS request it will return a single webpage saying "Unauthenticated" and explain how to sign into the VPN. A transparent proxy seems to be what I need, but my searches all seem to direct me to Squid, which is already running on my server and seems overkill for this simple task. Is there a simpler, lightweight program out there that does just this or should I just suck it up and run two instances of Squid (or figure out how to configure it)? Or, is this entire VPN thing I'm doing complete nonsense and I should just enable encryption on the wireless router?

  Read the article

• How to unblacklist an IP at Google?

  - by DJRayon

  I own a small business with two servers for webhosting. When setting up the primary (CentOS 5.5 + WHM, secondary is WHM DNS Only) server I kinda messed up the firewall, so the hackers could send stuff from my server. My primary IP is x.y.29.218. Anyway - I got blacklisted in several places, but now those blacklistings are gone. For a week or so, but Google still has my IP blacklisted. I handling serious damages because of that. Many clients want to switch from my hosting, etc. I've fixed the hole with CSF firewall SMTP_BLOCK option and enabled also the WHM SMTP TEAK Currently all I see from the Main Email View Mail Statistics (Errors section) in WHM is rows and rows of the following message removed-the-email-address-for-security R=lookuphost T=remote_smtp: SMTP error from remote mail server after end of data: host aspmx.l.google.com [a.b.39.27]: 550-5.7.1 [x.y.29.218 1] Our system has detected an unusual rate of\n550-5.7.1 unsolicited mail originating from your IP address. To protect our\n550-5.7.1 users from spam, mail sent from your IP address has been blocked.\n550-5.7.1 Please visit http://www.google.com/mail/help/bulk_mail.html to review\n550 5.7.1 our Bulk Email Senders Guidelines. h24si3868764fas.171 What are my options? I have one IP free. How can I configure Exim to send mail from that IP? My brain is like constantly blowing up because of this problem. Please someone, who has any knowledge how to deal with the current situation, please give me some kind of help - any help, suggestions, etc. I've tried everything I know, and I still don't know much, because this is the first time (I just started to webhost, etc) I deal with real physical servers not some kind of pre-setup VPS solution. Many - many thanks, whoever has time to offer some help.

  Read the article

• How to remove static IP from Mitel 5312 and enable DHCP

  - by jimbo

  I'm not sure this is the right forum for this question -- although I'm confident I'll be told if not! -- but I've read the fine manual (at least, such a manual as I have), I've googled and I cannot get any insight into where to even start solving this problem. I have a bunch of Mitel 5312 handsets, talking to a 3300 ICP controller. Some handsets are at a remote location, get an address from my DHCP server over there, and use the Mitel "Teleworker" extension to connect in over the Internet. The remaining handsets were set up with static IPs by a BT-supplied engineer, on the same subnet as the ICP itself. So far, so good. I have one remaining teleworker licence, and need to move a handset from the home location to the remote. I've managed to boot it and configure teleworker, but I cannot for the life of me see where I tell it to forget its static IP, and make a DHCP request. Any ideas? Should I be looking on the controller, or holding magic combinations of buttons on the handset itself? EDIT: Following some advice from Robert, below, I've broken out a spare device and reassigned the profile for this user's extension to the MAC of the new phone, and a new profile to the old MAC. Unfortunately this still doesn't get me anywhere -- the new handset now asks for the teleworker install password. I suspect I'm going to have to get a Mitel engineer involved here, since I've never been given that password... Unless anyone has any great ideas?

  Read the article

• Active Directory + IIS + SQL + ASP.NET

  - by Amira Elsayed Ismail

  I have sent the following question to stackoverflow website I have installed Windows server 2008 r2 on a virtual machine, Can I install Active directory with domain controller + IIS + SQL server on the same machine? I want to make web application and this web application will authenticate users from Active Directory, the web application should be published on the server IIS and the users should access it remotely from their home using domain name of my machine, Someone tell me that its very wrong to have IIS and Active directory on the same machine I got the following Answer You can't use ActiveDirectory over the internet. At least not without something like a VPN as a middle man. Their home computers will not be joined to the domain, so there is no pass-through authentication. Yes, it's a bad idea to put AD on the web server. Why is too complex to get into in an answer here. Suffice it to say that even if you did do this, it's probably would not work the way you are thinking it should. It's not impossible to do this. For instance, many of the Microsoft "Small Businesss" products put IIS, AD, and SQL Server on the same server. But, you kind of have to know what you're doing to configure it securely. Then I add the following comment Thanks for ur reply.so what you think about the best way to do this as I didn't do anything like that before should I install active directory on a machine and IIS on another machine ? and what about SQL should I add it to the same server of active directory ? I didn't mentioned also that it will be Microsoft dynamics server that will access some information about work and i have to read data from axapta also ? also what is VPN and how can I use it to let users access my web application anywhere ? Sorry for my long questions and thanks in advance so please if anyone can help I will be thankful

  Read the article

< Previous Page | 238 239 240 241 242 243 244 245 246 247 248 249  | Next Page >