Search Results

Search found 9889 results on 396 pages for 'pointer speed'.

Page 243/396 | < Previous Page | 239 240 241 242 243 244 245 246 247 248 249 250  | Next Page >

• Connecting two monitors at the corners

  - by fastmultiplication

  I am using two separate X screens on two monitors and I would like them to be connected at the lower right corner. That is, if you move to the lower right corner of screen0 the mouse should appear at the upper left of screen1. I do not want an entire edge of each monitor to be permeable to the mouse. I modified the xorg.conf file like so: Section "ServerLayout" Identifier "Layout0" Screen 0 "Screen0" 0 0 Screen 1 "Screen1" Relative "Screen0" 1200 1000 InputDevice "Keyboard0" "CoreKeyboard" InputDevice "Mouse0" "CorePointer" EndSection (screen 0's resolution is 1280x1024) so there is a bit of overlap. However whenever I move the mouse to the bottom of screen0, the pointer appears at the upper left of screen1. And, the entire top of screen1 is permeable to the mouse and brings it to the lower left corner of screen0. I have tried various numbers in following the "relative" statement - if I put 1280 1024 the mouse does not cross over at all. If I use 1280 1023 the entire right side of screen0 is permeable. I haven't been able to find any documentation about how to explicitly tell the mouse where to crossover - is there some? It seems that xorg is being really aggressive in guessing where the mouse crossover should take place. Does anyone know how to do this? Thanks!

  Read the article

• how to calculate intersection time and place of multiple moving arcs

  - by user20733

  I have rocks orbiting moons, moons orbiting planets, planets orbiting suns, and suns orbiting black holes, and the current system could have many many layers of orbitage. the position of any object is a function of time and relative to the object it orbits. (so far so good). now I want to know for a given 2 objects(A,B), a start time and a speed, how can I work out the when and where to go. I can work out where A and B is given a time. so i just need. 1: direction to travel in from A to B(remember B is moving(not in a straight line)) 2: Time to get to b in a straight line. travel must be in a straight line with the shortest possible distance. as an extension to this question, how will i know if its better to wait, EG is it faster to stay on object A and wait for a hour when the objects may be closer, than to set off from A to B at the start. Cheers, it hurt my brain.

  Read the article

• Quantify value for management

  - by nivlam

  We have two different legacy systems (window services in this case) that do exactly the same thing. Both of these systems have small differences for the different applications they serve. Both of these system's core functionality lies within a shared library. Most of the time, the updates occur in the shared library and we simply deploy the updated library to both of these systems. The systems themselves rarely change. Since both of these systems do essentially the same thing, our development team would like to consolidate these two systems into a single service. What can I do to convince management to allocate time for such a task? Some of the points I've noted are: Easier maintenance Decrease testing/QA time Unfortunately, this isn't enough. They would like us to provide them with hard numbers on the amount of hours this will save in the future and how this will speed up future development. Since most of the work is done in the shared library and the systems themselves never change, it's hard for us to quantify how many hours this will save. What kind of arguments can I make to justify the extra work to consolidate these systems?

  Read the article

• What are some best practices for minimizing code?

  - by CrystalBlue

  While maintaining the sites our development team has created, we have come across include files and plugins that have proven to be very useful to more then one part of our applications. Most of these modules have come with two different files, a normal source file and a min file. Seeing that the performance and speed of a page can be increased by minimizing the size of the file, we're looking into doing that to our pages as well. The problem that we run into is a lot of our normal pages (written in ASP classic) is a mix of HTML, ASP, Javascript, CSS, and include files. We have some pages that have their JS both in include files and in the page, depending on if the function is only really used in that page or if it's used in many other pages. For example, we have a common.js and an ajax.js file, both are used in a lot of pages, but not all of them. As well as having some functions in a page that doesn't really make sense to put into one master page. What I have seen a few other people do online is use one master JS file and place all of their javascript into that, minify it, gzip it, and only use that on their production server. Again, this would be great, but I don't know if that fully works for our purposes. What I'm looking for is some direction to go with on this. I'm in favor of taking all of our JS and putting it in one include file, and just having it included in every page that is hit. However, not every page we have needs every bit of JS. So would it be worth the compilation and minifying of the files into one master file and include it everywhere, or would it be better to minify all other files and still include them on a need-to-use basis?

  Read the article

• Oracle Solaris 11.1 available today

  - by user12611852

  Today Oracle is pleased to announce availability of Oracle Solaris 11.1. Download Solaris 11.1 Order Solaris 11.1 media kitExisting customers can quickly and simply update using the network based repository Highlights include: 8x faster database startup and shutdown and online resizing of the database SGA with a new optimized shared memory interface between the database and Oracle Solaris 11.1 Up to 20% throughput increases for Oracle Real Application Clusters by offloading lock management into the Oracle Solaris kernel Expanded support for Software Defined Networks (SDN) with Edge Virtual Bridging enhancements to maximize network resource utilization and manage bandwidth in cloud environments 4x faster Solaris Zone updates with parallel operations shorten maintenance windows New built-in memory predictor monitors application memory use and provides optimized memory page sizes and resource location to speed overall application performance. Learn more and share these valuable tools with your customers to enable them to move to Oracle Solaris 11.1 quickly. Many customers wait for the first update --now is the time to encourage them to install Oracle Solaris 11.1. Oracle Solaris 11.1 Data Sheet  What's New in Oracle Solaris 11.1 Oracle Solaris 11.1 FAQs Oracle Solaris 11 .1 Customer Presentation Oracle Solaris 11.1 is recommended for all SPARC T4 Systems and will soon be available preinstalled.

  Read the article

• Help w/ iPad 1 performance for tile-based DOM Javascript game

  - by butr0s

  I've made a 2D tile-based game with DOM/Javascript. For each level, the map data is loaded and parsed, then lots of tiles ( elements) are drawn onto a larger "map" element. The map is inside of a container that hides overflow, so I can move the map element around by positioning it absolutely. Works a treat on desktop browsers, and my iPad 2. My problem is that performance is really bad on iPad 1. The performance hit is directly related to all the tile elements in my map, because when I remove or reduce the number of tiles drawn, performance improves. Optimizing my collision detection loop has no effect. My first thought was to batch groups of tiles into containers, then hide/show them based on proximity to the player, however this still causes a huge hiccup when the player moves and a new group of tiles is displayed (offscreen). Actually removing the out-of-sight elements from the DOM, then re-adding them as necessary is no faster. Anyone know of any tips that might speed up DOM performance here? My map is 1920 x 1920 pixels, so as far as I know should be within the WebKit texture limit on iOS 5/iPad. The map is being moved with CSS3 transforms, and I've picked all the other obvious low-hanging fruit.

  Read the article

• C# XNA 2D Multiple boxes collision detection and movement

  - by zini

  Hi, I've been making simple game where you shoot boxes that are coming towards you. All game objects are simple rectangles. Now I have problem with collision detection; how to check where the collision comes so I can change the coordinates right? I have this kind of situation: http://imgur.com/8yjfW Imagine that all of those blocks are moving towards you (green box). If those orange boxes collide with each other, they should "avoid" themselves and not go through each other. I have class Enemy which has properties x, y and such. Now I'm doing the collision like this: // os.Count is an amount of other enemies colliding with this enemy if (os.Count == 0) { // If enemy doesn't collide with other enemy lasty = y; lastx = x; slope = (x - player.x) / (y - player.y); x += slope * l; // l is "movement speed" of enemy (float) if (y > player.y) { y = lasty; } else if (y < player.y) { y += l; } } else { foreach(Enemy b in os) { if (b.y > this.y) { // If some colliding enemy is closer player than this enemy, that closer one will be moved towards the player b.lasty = b.y; if (!BiggestY(os)) { // BiggestY returns true if this enemy has the biggest Y b.y += b.l; } b.x = b.lastx; } } } But this is very, very bad way to do this. I know it, but I just can't figure out other way. And as a matter in fact, this method doesn't even work pretty good; if multiple enemies are colliding same enemy they go through each other. I explained this pretty badly, but I hope that you understand this. And to sum up, as I said: How to check where the collision comes so I can change the coordinates right?

  Read the article

• Cloud Strategy for Partners Announced at OOW

  - by Cinzia Mascanzoni

  Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0cm 5.4pt 0cm 5.4pt; mso-para-margin:0cm; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Calibri","sans-serif"; mso-bidi-font-family:"Times New Roman";} Oracle made a significant announcement about its Cloud Strategy for partners: Oracle has unveiled a comprehensive new set of Oracle Cloud partner programs and enablement resources that help partners to speed time to market with new cloud-based services and solutions and deliver increased value to customers. Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0cm 5.4pt 0cm 5.4pt; mso-para-margin:0cm; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Calibri","sans-serif"; mso-bidi-font-family:"Times New Roman";} New Oracle PartnerNetwork Cloud offerings include an Oracle Cloud Referral Program, Oracle Cloud Specialization featuring RapidStart and Oracle Cloud Builder Specializations, Oracle Cloud Resale Program and Oracle Platform Services for Independent Software Vendors (ISVs).

  Read the article

• OSB, Service Callouts and OQL

  - by Sabha

  Oracle Fusion Middleware customers use Oracle Service Bus (OSB) for virtualizing Service endpoints and implementing stateless service orchestrations. Behind the performance and speed of OSB, there are a couple of key design implementations that can affect application performance and behavior under heavy load. One of the heavily used feature in OSB is the Service Callout pipeline action for message enrichment and invoking multiple services as part of one single orchestration. Overuse of this feature, without understanding its internal implementation, can lead to serious problems. This series will delve into OSB internals, the problem associated with usage of Service Callout under high loads, diagnosing it via thread dump and heap dump analysis using tools like ThreadLogic and OQL (Object Query Language) and resolving it. The first section in the series will mainly cover the threading model used internally by OSB for implementing Route Vs. Service Callouts. The second section of the "OSB, Service Callouts and OQL" blog posting will delve into thread dump analysis of OSB server and detecting threading issues relating to Service Callout and using Heap Dump and OQL to identify the related Proxies and Business services involved. The final section of the series will focus on the corrective action to avoid Service Callout related OSB serer hangs. Before we dive into the solution, we need to briefly discus about Work Managers in WLS. Please refer to the blog posting for more details.

  Read the article

• Common way to store model transformations

  - by redreggae

  I ask myself what's the best way to store the transformations in a model class. What I came up with is to store the translation and scaling in a Vector3 and the rotation in a Matrix4. On each update (frame) I multiply the 3 matrices (first build a Translation and Scaling Matrix) to get the world matrix. In this way I have no accumulated error. world = translation * scaling * rotation Another way would be to store the rotation in a quaternion but then I would have a high cost to convert to a matrix every time step. If I lerp the model I convert the rotation matrix to quaternion and then back to matrix. For speed optimization I have a dirty flag for each transformation so that I only do a matrix multiplication if necessary. world = translation if (isScaled) { world *= scaling } if (isRotated) { world *= rotation } Is this a common way or is it more common to have only one Matrix4 for all transformations? And is it better to store the rotation only as quaternion? For info: Currently I'm building a CSS3D engine in Javascript but these questions are relevant for every 3D engine.

  Read the article

• I'm a Subversion geek, why should I consider or not consider Mercurial or Git or any other DVCS?

  - by user2567

  I try to understand the benefits of distributed version control system (DVCS). I found Subversion Re-education and this article by Martin Fowler very useful. Mercurial and others DVCS promote a new way of working on code with changesets and local commits. It prevents from merging hell and other collaboration issues We are not affected by this as I practice continuous integration and working alone in a private branch is not an option, unless we are experimenting. We use a branch for every major version, in which we fix bugs merged from the trunk. Mercurial allows you to have lieutenants I understand this can be useful for very large projects like Linux, but I don't see the value in small and highly collaborative teams (5 to 7 people). Mercurial is faster, takes less disk space and full local copy allows faster logs & diffs operations. I'm not concerned by this either, as I didn't notice speed or space problems with SVN even with very large projects I'm working on. I'm seeking for your personal experiences and/or opinions from former SVN geeks. Especially regarding the changesets concept and overall performance boost you measured. UPDATE (12th Jan): I'm now convinced that it worth a try. UPDATE (12th Jun): I kissed Mercurial and I liked it. The taste of his cherry local commits. I kissed Mercurial just to try it. I hope my SVN Server don't mind it. It felt so wrong. It felt so right. Don't mean I'm in love tonight. FINAL UPDATE (29th Jul): I had the privilege to review Eric Sink's next book called Version Control by Example. He finished to convince me. I'll go for Mercurial.

  Read the article

• ubuntu 11.10 can't find wireless after waking from sleep

  - by Colleen

  I've tried a lot of proposed solutions, most of them adding files to /etc/pm/config.d, as well as WiFi stops working after waking from suspend and nothing has worked. hardware info: [colleen@colleen-HP ~]$ sudo lshw -C network [sudo] password for colleen: *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:07:00.0 logical name: eth0 version: 06 serial: 2c:27:d7:b1:ea:67 size: 10Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=N/A latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:41 ioport:4000(size=256) memory:c1404000-c1404fff memory:c1400000-c1403fff *-network description: Wireless interface product: Centrino Wireless-N 1000 vendor: Intel Corporation physical id: 0 bus info: pci@0000:0d:00.0 logical name: wlan0 version: 00 serial: 8c:a9:82:99:48:8c width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlagn driverversion=3.0.0-21-generic-pae firmware=39.31.5.1 build 35138 ip=192.168.0.4 latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:48 memory:c5500000-c5501fff Is anyone else still having this problem? The two solutions I haven't tried are installing wicd and upgrading because I've heard both are kind of unstable/buggy and wicd frankly scares me.

  Read the article

• How to make backlight work on Acer 5732z?

  - by Dude Random21

  I want to run 12.04 on my Acer Aspire 5732z. I know from research that these computers have issues with the backlight on Ubuntu. So I tried a couple of solutions: The sudo lightdm restart method. I get no change at all. The sudo setpci -s 00:02.0 F4.B=30 method. This so far has been the most effective. I first tried it in the F1 console, right away I get the screen back, problem is going back to the desktop it goes back to being black. So I tried it from a terminal window and it works as well but as soon as I unplug my external monitor the screen turns black again and doesn't come back. If I plug the monitor back in the screen stays black and the only thing I see is the mouse pointer. From here I go back into console (which I am able to see) and reboot from there. The sudo sed -i 's/GRUB_CMDLINE_LINUX=""/GRUB_CMDLINE_LINUX="acpi_osi=Linux"/g /etc/default/grub method. This one I got no instant change and after reboot still no change. I'm open to pretty much any suggestions you may have.

  Read the article

• Lenovo v570 ubuntu 12.04 wireless hard blocked even when ext. switch is on

  - by user100987

  When I run iwconfig it say's lo and eth0 have no wireless extensions, but wlan0 it says IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=off Retry long limit:7 RTS the:off Fragment the:off Power Management:off and I believe that's my problem, I just don't know how to turn it back on Any help? When I ran lspci | grep Network it gave me this 02:00.0 Network controller: Intell Corporation Centrino Wireless -N + WiMAX 6150 (rev 67) How I know that my wireless is hard blocked because when I run sudo rfkill list all I get 0: Ideapad_wlan: Wireless LAN Soft blocked: no Hard blocked: no 1: phy0: Wireless LAN Soft blocked: no Hard blocked: yes when I run lshw -c network I get. *-network DISABLED description: Wireless interface product: Centrino Wireless-N + WiMAX 6150 vendor: Intel Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: mon1 version: 67 serial: 40:25:c2:d2:96:2c width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list logical wireless ethernet physical configuration: broadcast=yes driver=iwlwifi driverversion=3.2.0-32-generic-pae firmware=41.28.5.1 build 33926 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:43 memory:d0500000-d0501fff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 06 serial: f0:de:f1:d7:a0:4d size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8168e-2.fw ip=192.168.0.65 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:41 ioport:2000(size=256) memory:d0404000-d0404fff memory:d0400000-d0403fff

  Read the article

• Optimising news fetching

  - by aceBox

  I have a web scraper for scraping news from different sources in wp7. My current appraoch for doing this is: load newspapers information from xml file. go to the specified sections and fetch the urls of the news items. go to each url and fetch headline, image, publisher. display using a MVVM architecture of windows phone. The whole thing takes place asynchronously...meaning as soon as url from a section of a newspaper is fetched it is added to the queue, and the second stage consisting of fetching headline, image etc starts... and as soon this is fetched even for one article, it is displayed. Later on as more articles are fetched, they are added on to the list. For the fetching purpose I am using a SmartThreadPool(http://www.codeproject.com/Articles/7933/Smart-Thread-Pool) for windows phone. My problem is that...even for fetching around 80 items (in total) from 9 publications, it is taking more than a minute. How can i speed up the procedure? Note: I have a two stage approach because many times the images are not available with headlines, and are only found in the article.

  Read the article

• Shader compile log depending on hardware

  - by dreta

  I'm done with the core of my graphics engine and I'm testing it on every platform I can get my hands on. Now, what I noticed is that different drivers return different shader and program compile log content. For example, on my friend's laptop if you successfuly compile a shader then the log is simply empty. However on my PC I get some useful information along with it. So if I compile a vertex shader, I'll get: Vertex shader was successfully compiled to run on hardware. Which isn't that impressive, but is what happens when I compile a program. On my friend's computer the log is empty, since the program compiles. However on my own computer I get: Vertex shader(s) linked, fragment shader(s) linked. Which is awesome, because I'm attaching a geometry shader with 0 (I have a geometry shader file with trash, so it doesn't compile and the pointer is set to 0), and the compiler just tells me which shaders linked. Now it got me thinking, if I was going to buy a graphics card, is there a way for me to get the information about whether or not I'll get this "extended" compile information? Maybe it's vendor specific? Now I don't expect an answer TBH, this seems a bit obscure, but maybe somebody has any experience with this and could post it.

  Read the article

• UBUNTU's Network Connection Manger can't detect Huawei ETS2051 Modem device!

  - by Doctoa

  I have a modem device called Huawei ETS2051 and the Network Connection Manger can't detect it, but when I use Gnome-PPP it work fine but the problem is when I use Gnome-PPP; apps like Ubuntu software Center Can't reconice that's Iam connecting to the Internet so the app is just act like it's offline while other apps like web browsers and IM's work good under Gnome-PPP. any way what I want is to have a Full Ubuntu experince by making The Network Connection Manger detect my ETS2051. I have another 3G USB modem and The Network Connection Manger detect it and it's work just fine but the internet price for this one is high and I can't effort it so am count on that ETS2051 modem as you can see for it's low price and stable internet speed that satesfy my needs. More information: Gnome-PPP is a GUI for wvdial. the ETS2051 modem use a serial USB port. I have a Windows driver CD for the device. I have also find This qustion about the software Center acting like it's offline around wvdial and there's this launchpad bug. and am really insest to use Ubuntu Software Center so please no other software manger apps recomendation... I've also this Genius ColorPage HR6X Slim scanner that's Ubuntu can't detect it, so if you interset you can check and answer the qustion from here...

  Read the article

• Target a specific Button and Style it

  - by CoffeeAddict

  I've got a button inside my div. The image is showing some kind of padding around it <div id="member-name" hidden="true"> <span><button id="expandButton"><img src="~/Content/Images/plus.jpg" /></button></span><p id="member-fullName"></p> </div> Not sure how to get rid of this issue, see the grey around that plus image..I want to get rid of that. Here's the image alone, see that there is nothing around it: here is my css (just various related snippets to all this): div { padding: 0px;} input[type="submit"], input[type="button"], button { background-color: #ffffff; cursor: pointer; font-size: 11px; font-weight: 600; padding: 0px; margin: 0px; width: auto; vertical-align: middle; } #member-name { margin: 30px 0px 0px 0px; height: 20px; font-weight: bold; color: white; padding: 1px 1px 0px 1px; background-color: #d28105; border: 1px solid darkgray; overflow: hidden; } #member-name.p { display: inline-block; } /* #member-name.input[type="submit"] { margin: 0px;padding: 0px; } - this does not work, probably wrong syntax anyway */

  Read the article

• Will the Driver Support for Intel HD Graphics be Improved in 12.10?

  - by Hiranya

  I recently installed Ubuntu 12.04 on a HP Pavilion dv4 laptop. This is a core i7 machine with Intel HD graphics and also a separate nVidia VGA card. I had a lot of issues getting Ubuntu 12.04 working on this system. First there were issues booting up the live CD for installation. I worked around that by using the 'nomodeset' option. Then I continued to have similar issues after installation has completed. So I had to permanently add the nomodeset option to my GRUB boot configuration. At the moment I have a working installation but there are many issues: Ubuntu GUI is a bit flaky at times. The mouse pointer goes on and off when hovering over certain icons. Certain things doesn't get rendered properly on the screen. I can't access any of the tty consoles. Hitting Ctrl+Alt+F[1-6] gives me a blank screen. And once that happens I can't even come back to the UI by hitting Ctrl+Alt+F7. I've realized that tty consoles are actually working. I just can't see the text. If I enter a command like 'sudo reboot' into the empty screen the machine reboots. Can't get external displays (monitors, projectors etc) working. But I think this is probably because the VGA out is wired to the nVidia card which is not being used by Linux. colord program crashes every now and then triggering a popup message. So my main question is, will the support for Intel HD graphics be improved in the next release? Or will I have to keep using the nomodeset option in the new release too? Also I appreciate if anybody can shed some light on any of the issues listed above. Thanks in advance.

  Read the article

• Ubuntu 12.04 takes too long to boot

  - by msPeachy

  I've recently encountered the following error message: mount: mounting /dev/disk/by-uuid/3f7f5cd9d-6ea3-4da7-b5ec-**** on /root failed: Invalid argument mount: mounting /sys on /root/sys failed: No such file or directory mount: mounting /dev on /root/dev failed: No such file or directory mount: mounting /sys on /root/sys failed: No such file or directory mount: mounting /proc on /root/proc failed: No such file or directory Target file system doesn't have /sbin/init. No init found. Try passing init= bootarg. Busybox v1.18.5 (Ubuntu 1:1.18.5-1ubuntu4) built-in shell (ash) Enter 'help' for a list of built-in commands. (initramfs) _ I run sudo fsck /dev/sda2 which is the Ubuntu ext4 root partition via LiveCD. It checked and fixed the file system. The next time I boot, Ubuntu started to load with the Ubuntu logo and the dots underneath for several hours (with the mouse pointer active on the screen), I even let the computer on overnight but still it did not successfully boot or got to the login screen in the morning. I booted again with the LiveCD and checked the NTFS partitions with ntfsfix and again the NTFS partitions was checked and fixed successfully. I also edited my fstab and commented out the lines that auto-mounts the NTFS partitions. The next time I boot, it took almost 20 minutes for Ubuntu to get to the login screen, after typing the password it took an additional 10 minutes for Ubuntu to get to the desktop. On the desktop, it take several minutes to open any program, displaying the Dash alone takes 5 minutes! Is there a fix for this without having to reinstall Ubuntu? I don't see or get any errors, Ubuntu is just taking too long to boot and to run programs. Please help!

  Read the article

• Unable to make sound play in headset

  - by user50849

  Top right, I click the sound icon, select sound settings, and connect my USB-headset. I can them see the headset being detected as it pops up in the menu. I click it, and expect the currently played audio to get sent to the headset instead. My problem is that it does not. The audio keeps playing through the built-in speakers. More info: The icon for my built-in card in the sound settings is a circuit with a note symbol on top. The symbol for the headset is just black background with a "No" symbol on it. Might mean it doesn't work somehow. I installed pavucontrol, and notice that no second sound card shows up in there. When connecting, the syslog says Jun 20 09:38:46 yuna kernel: [40144.553431] usb 2-1.2: new full-speed USB device number 11 using ehci_hcd Jun 20 09:38:46 yuna kernel: [40144.650609] input: C-Media USB Headphone Set as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.2/2-1.2:1.3/input/input20 Jun 20 09:38:46 yuna kernel: [40144.650895] generic-usb 0003:0D8C:000C.000B: input,hidraw0: USB HID v1.00 Device [C-Media USB Headphone Set ] on usb-0000:00:1d.0-1.2/input3 Jun 20 09:38:46 yuna mtp-probe: checking bus 2, device 11: "/sys/devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.2" Jun 20 09:38:46 yuna mtp-probe: bus: 2, device: 11 was not an MTP device

  Read the article

• Unable to enable wireless in ubuntu 12.04

  - by Joe

  I have a Vostro 2520 and not sure how to enable wireless on my machine. The details are given below, would appreciate any pointers to resolving this issue. lsmod returns Module Size Used by ath9k 132390 0 ath9k_common 14053 1 ath9k ath9k_hw 411151 2 ath9k,ath9k_common ath 24067 3 ath9k,ath9k_common,ath9k_hw b43 365785 0 mac80211 506816 2 ath9k,b43 cfg80211 205544 4 ath9k,ath,b43,mac80211 bcma 26696 1 b43 ssb 52752 1 b43 ndiswrapper 282628 0 ums_realtek 18248 0 usb_storage 49198 1 ums_realtek uas 18180 0 snd_hda_codec_hdmi 32474 1 snd_hda_codec_cirrus 24002 1 joydev 17693 0 parport_pc 32866 0 ppdev 17113 0 rfcomm 47604 0 bnep 18281 2 bluetooth 180104 10 rfcomm,bnep psmouse 97362 0 dell_wmi 12681 0 sparse_keymap 13890 1 dell_wmi snd_hda_intel 33773 3 snd_hda_codec 127706 3 snd_hda_codec_hdmi,snd_hda_codec_cirrus,snd_hda_intel snd_hwdep 13668 1 snd_hda_codec snd_pcm 97188 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec snd_seq_midi 13324 0 snd_rawmidi 30748 1 snd_seq_midi snd_seq_midi_event 14899 1 snd_seq_midi snd_seq 61896 2 snd_seq_midi,snd_seq_midi_event snd_timer 29990 2 snd_pcm,snd_seq snd_seq_device 14540 3 snd_seq_midi,snd_rawmidi,snd_seq wmi 19256 1 dell_wmi snd 78855 16 snd_hda_codec_hdmi,snd_hda_codec_cirrus,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device mac_hid 13253 0 i915 473240 3 drm_kms_helper 46978 1 i915 uvcvideo 72627 0 drm 242038 4 i915,drm_kms_helper videodev 98259 1 uvcvideo soundcore 15091 1 snd dell_laptop 18119 0 dcdbas 14490 1 dell_laptop i2c_algo_bit 13423 1 i915 v4l2_compat_ioctl32 17128 1 videodev snd_page_alloc 18529 2 snd_hda_intel,snd_pcm video 19596 1 i915 serio_raw 13211 0 mei 41616 0 lp 17799 0 parport 46562 3 parport_pc,ppdev,lp r8169 62099 0 sudo lshw -class network *-network UNCLAIMED description: Network controller product: Broadcom Corporation vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:07:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:f7c00000-f7c07fff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:09:00.0 logical name: eth0 version: 07 serial: 78:45:c4:a3:aa:65 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl8168e-3_0.0.4 03/27/12 ip=192.168.1.5 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:41 ioport:e000(size=256) memory:f0004000-f0004fff memory:f0000000-f0003fff rfkill list all 0: dell-wifi: Wireless LAN Soft blocked: yes Hard blocked: yes 1: dell-bluetooth: Bluetooth Soft blocked: yes Hard blocked: yes

  Read the article

• Which programming language should I choose I want to build this website ...? [closed]

  - by Goma

  Assuming that I will start with just phot sharing website. Every user can add comments to any photo. After that the site will contain news (general news), the admin can add any news and the moderators as well while the users can also add comments on this news. The website will aslo provide photos uploader, so every user will have up to 20 MB ti upload any photos they want. Other users can see these photos or can not depending on the option that the main user chose(if he wants to publish his photos or not). The site should have a small type of forum which provide the ability for admin to ad categories and for user to add topics and replies for each topic in these categoris. These are the things that I can think of now, but the website will add other features as well and services later on. Can you tell me now which programming language can help me to do all that? I need a programming language that provdies the follwing: 1- speed load for pages of the site. 2- easy to add more functions quickly and easy to edit code for any reason. 3- Secure 4- fast in displaying infromation from database.

  Read the article

• Prevent Nautilus from displaying thumbnails on a specific mount

  - by Zakhar

  I have written a filesystem over Fuse to access a remote pseudo-NAS (the French "Freebox V6", I'll soon publish it as GPL3... when it's a little bit more polished!). The NAS is connected to a home ADSL, thus data comes down at the upload speed of ADSL, which is at best 1Mbps. My mount works fine (read-only at the moment), but Nautilus sees the mountpoint (and all sub-directories) as a "local" filesystem and tries to make thumbnails. As I have a directory full of images, this is quite horrible, because Nautilus then opens ALL the images to try to display the thumbnail. I could switch the Nautilus preferences to "Never" for thumbnails, but then I'll loose thumbnails on my "real" local filesystem. So the question is: with the preference "Only for local filesystem", how can I instruct Nautilus that my mountpoint is in fact NOT a local mount so that it will stop trying to draw thumbnails on that specific mount, but continue "thumbnailing" on mounts that are really local? Edit note: the same things happens if you use "standard worldwide" mounts such as sshfs, davfs,... as long as you mount over a relatively slow network (ADSL) and have images/movies on your mounted tree.

  Read the article

• raid advice with SSD and two HDD

  - by Nin

  I have a new machine with one 128GB SSD and two 1TB HDD. On the SSD is the OS and my initial thought was to put the two HDD in RAID 1 for user data. After some more thought I came up with two other setups and now I'm in doubt :) Can someone advise what would be the best setup? 1: single SSD and HDD in RAID 1 (original thought) 2: Create 2 partitions on the HDD (128GB and 872GB). Put the two 872GB in RAID 1 and create another RAID 1 with the SSD and one 128GB HDD partition. 3: Create 2 partitions on the HDD (750/250), put the 705GB in RAID 1 and use the 2 250GB as backup and make automatic snapshots of the SSD to (one of) these partitions. I think the 2 main questions are: Is it advisable to create a raid array with only part of a drive and actively use the other part of that drive or should you always use the full disk? Is it advisable to create a raid 1 array with a SSD and HDD or will that blow the whole speed advantage of the SSD?

  Read the article

< Previous Page | 239 240 241 242 243 244 245 246 247 248 249 250  | Next Page >