Search Results

Search found 8401 results on 337 pages for 'bad habits'.

Page 244/337 | < Previous Page | 240 241 242 243 244 245 246 247 248 249 250 251 | Next Page >

Which HDD brand do you ..trust

- by Shiki

Okay it says its 'subjective' but I believe it's not. Basically I want to ask the community about your preference. Not really 'preference' but actual experience. Like if you never had a problem with Western Digital, then write that in an answer, or if there is one with WD, just vote it up. And so on. (Heard so many stories, experiences. I only had Samsung, Maxtor, WD, Seagate HDDs. Samsung died with bad blocks, had anomalies. Maxtor died so fast I couldn't even try it really and it's really hot, loud. Seagate is just as loud as a jet plane, and moderately hot. My WD (green) is quiet, really cool and somewhat fast. That's all I have about experiences. So I would say Western Digital in an answer (OR Hitachi. Never had one yet, but every expert I know says I should get one since they even had problems with WD but Hitachi seems to be ok. (My laptop comes with Hitachi hdd but I don't think its really relevant.)) Basically I mean desktop 7200RPM HDDs here. Well.. notebook HDDs are ok also, but no raptor/scsi/server ones. Hope you get what I meant and it won't get closed.

Read the article
Problem routing between directly connected Subnets w/ ASA-5510

- by Zephyr Pellerin

This is an issue I've been struggling with for quite some time, with a seemingly simple answer (Aren't all IT problems?). And that is the problem of passing traffic between two directly connected subnets with an ASA While I'm aware that best practice is to have Internet - Firewall - Router, in many cases this isn't possible. For example, In have an ASA with two interfaces, named OutsideNetwork (10.19.200.3/24) and InternalNetwork (10.19.4.254/24). You'd expect Outside to be able to get to, say, 10.19.4.1, or at LEAST 10.19.4.254, but pinging the interface gives only bad news. Result of the command: "ping OutsideNetwork 10.19.4.254" Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 10.19.4.254, timeout is 2 seconds: ????? Success rate is 0 percent (0/5) Naturally, you'd assume that you could add a static route, to no avail. [ERROR] route Outsidenetwork 10.19.4.0 255.255.255.0 10.19.4.254 1 Cannot add route, connected route exists At this point, you might gander if its a NAT or Access list problem. access-list Outsidenetwork_access_in extended permit ip any any access-list Internalnetwork_access_in extended permit ip any any There is no dynamic nat (or static nat for that matter), and Unnatted traffic is permitted. When I try pinging the above address (10.19.4.254 from Outsidenetwork), I get this error message from level 0 logging (debugging). Routing failed to locate next hop for icmp from NP Identity Ifc:10.19.200.3/0 to Outsidenetwork:10.19.4.1/0 This led me to set same-security traffic permit, and assigned the same, lesser and greater security numbers between the two interfaces. Am I overlooking something obvious? Is there a command to set static routes that are classified higher than connected routes?

Read the article
How to set up RAID-0 first time on new PC?

- by jasondavis

I have built basic PC's in the past but have never used a RAID array at all. SO now I am buying parts to build my new PC, it will be an intel i7 processor. My motherboard will have RAID support which I will use instead of an aftermarket raid controller for now. Also I plan to use 2 SSD drives in RAID-0 for my windows 7 OS. (Please note that I am aware of the issues with doing this, including lack of TRIM support when using RAID with SSD drives. I am OK with it not working as I can just re[place the drives in a year or so or wheneer they become more sluggish). SO here is my question part. If I assemble the motherboard, PSU, processor, RAM, vidm card, etc and then go to turn the PC on, it will have the 2 SSD drives hooked up. so I assume I will then soon the BIOS screen before I install windows? How to I go about making the 2 drives work in RAID-0 at this point? I do the raid part before installing my OS right? Please help with the steps involved from assembling the parts of the PC and then turning it on, to the part of getting the RAID-0 set up between the 2 drives and then installing my windows 7 OS from a Optical drive? Please help, all advice, instructions, tips appreciated as long as on topic. I do not need to be told that this is a bad idea as far as if 1 drive fails I losse it all, I plan on having a disk IMAGE to be able to restore my OS and software to a new set of drives at anytime needed in the event of drive failure. Same goes for lack of TRIM support. Thanks for reading and help =)

Read the article
Apache reports a 200 status for non-existent WordPress URLs

- by Jonah Bishop

The WordPress .htaccess generally has the following rewrite rules: # BEGIN WordPress <IfModule mod_rewrite.c> RewriteEngine On RewriteBase / RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d RewriteRule . /index.php [L] </IfModule> When I access a non-existent URL at my website, this rewrite rule gets hit, redirects to index.php, and serves up my custom 404.php template file. The status code that gets sent back to the client is the correct 404, as shown in this HTTP Live Headers output example: http://www.borngeek.com/nothere/ GET /nothere/ HTTP/1.1 Host: www.borngeek.com {...} HTTP/1.1 404 Not Found However, Apache reports the entire exchange with a 200 status code in my server log, as shown here in a log snippet (trimmed for simplicity): {...} "GET /nothere/ HTTP/1.1" 200 2155 "-" {...} This makes some sense to me, seeing as the original request was redirected to page that exists (index.php). Is there a way to force Apache to report the exchange as a 404? My problem is that bogus requests coming from Bad Guys show up as "successful requests" in the various server statistics software I use (AWStats, Analog, etc). I'd love to have them show up on the Apache side as 404s so that they get filtered out from the stat reports that get generated. I tried adding the following line to my .htaccess, but it had no effect (I'm guessing for the same reason as the previous redirect rules): ErrorDocument 404 /index.php?error=404 Does anyone have a clever way to fix this annoyance? Additional Info: OS is Debian 6.0.4, and Apache version looks to be 2.2.22-3 (hosted on DreamHost) The 404 being sent back to the client is being set by WordPress (i.e. I'm not manually calling header() anywhere)

Read the article
Ext3 fs: Block bitmap for group 1 not in group (block 0). is fs dead?

- by ip

My company has a server with one big partition with Mysql database and php files. Now this partition seems to be corrupted, as reported from kernel messages when I tried to mount it manually: [329862.817837] EXT3-fs error (device loop1): ext3_check_descriptors: Block bitmap for group 1 not in group (block 0)! [329862.817846] EXT3-fs: group descriptors corrupted! I've tried to recovery it running tools from a PLD livecd. These are the tools I have tested: - e2retrieve - testdisk - photorec - dd_rescue/dd_rhelp - ddrescue - fsck.ext2 - e2salvage without any success. dumpe2fs 1.41.3 (12-Oct-2008) Filesystem volume name: /dev/sda3 Last mounted on: <not available> Filesystem UUID: dd51610b-6de0-4392-a6f3-67160dbc0343 Filesystem magic number: 0xEF53 Filesystem revision #: 1 (dynamic) Filesystem features: has_journal filetype sparse_super Default mount options: (none) Filesystem state: not clean with errors Errors behavior: Continue Filesystem OS type: Linux Inode count: 9502720 Block count: 18987570 Reserved block count: 949378 Free blocks: 11555345 Free inodes: 11858398 First block: 0 Block size: 4096 Fragment size: 4096 Blocks per group: 32768 Fragments per group: 32768 Inodes per group: 16384 Inode blocks per group: 512 Last mount time: Wed Mar 24 09:31:03 2010 Last write time: Mon Apr 12 11:46:32 2010 Mount count: 10 Maximum mount count: 30 Last checked: Thu Jan 1 01:00:00 1970 Check interval: 0 (<none>) Reserved blocks uid: 0 (user root) Reserved blocks gid: 0 (group root) First inode: 11 Inode size: 128 Journal inode: 8 Journal backup: inode blocks dumpe2fs: A block group is missing an inode table while reading journal inode e2fsck 1.41.3 (12-Oct-2008) fsck.ext3: Group descriptors look bad... trying backup blocks... fsck.ext3: A block group is missing an inode table while checking ext3 journal for /dev/sda3 I tried also backup superblocks, same error result. There's any other tools I have to test before considering these disk definitely unrecoverable? Many thanks, ip

Read the article
All commands stopped working in centos 6.5

- by Michael

I have made a big mistake while removing some duplicate packages as it appears to be broken. yum 1036 rpm -e --nodeps glibc-2.12-1.132.el6_5.2.x86_64 1037 rpm -e --nodeps nscd-2.12-1.132.el6_5.2.x86_64 1038 rpm -e --nodeps glibc-common-2.12-1.132.el6_5.2.x86_64 1040 rpm -e --nodeps glibc-common-2.12-1.132.el6.x86_64 glibc-devel-2.12-1.132.el6.x86_64 glibc-headers-2.12-1.132.el6.x86_64 1041 rpm -e glibc.x86_64 1042 rpm -e --nodeps glibc.x86_64 The issue happened after doing 1042 step. None of commands work(including yum, rpm, ls, cp etc) and getting error /lib64/ld-linux-x86-64.so.2: bad ELF interpreter: No such file or directory I thought that installing glibc after removing all the current ones would help to resolve the duplicate package error :( Now I realised that it is used as the C library in the GNU system and most systems with the Linux kernel. It defines the "system calls" and other basic facilities such as open, malloc, printf, exit, etc. Is there any possible solutions other than reinstall? I have lost ssh access. Maybe anything can be done using rescue cd? Thanks

Read the article
SQL Server replication and load balance

- by Ahmed Galal

I'm running a web service that serves a mobile app on IIS 8 and SQL Server 2014, my service has a massive load and i'm trying to improve performance, most of the load is happening on SQL. i don't think i have a bottleneck, my processor and ram is up to the max and i think my code is not that bad, am already using memcached and other stuff to avoid hitting SQL too much. i know i can always upgrade the server hardware but i already have a spare server that i would like to use, so i was thinking to split the SQL load on the 2 servers. What i was thinking of is to setup replication on the other server and do some load balancing, but am not sure how to do the load balance. I know i can adjust my code to hit the other server for some queries but i was hoping to find a solution that avoid changing my code. So my question is, What are the ways of doing load balancing between 2 SQL servers ? I would appreciate suggestions or best practices or some directions. Thanks.

Read the article
Linux VLAN Bridge

- by raspi

I have home network with VLANs, one for LAN, one for WLAN and one for internet. I'd like to use bridging so that instead of configuring these same VLANs to every machine, they had own VLAN ID and bridges were LAN, WLAN and internet. I've tried it but for some reason keep-alive/ttl seems to get broken because SSH sessions etc suddenly disconnects. We have this same setup working in workplace for 4+ years with 100+ customers but it's custom firewall/router hardware so accessing it is impossible. I know that it runs Linux. So what is Debian/Ubuntu default network settings doing wrong or is it just NIC driver/hw problem? I've tried to mess araund with ttl etc settings without any luck. The bad stuff is happening in the bridge because current VLAN-only setup works fine. interfaces: auto lo iface lo inet loopback # The primary network interface allow-hotplug eth0 allow-hotplug eth1 iface eth0 inet static iface eth1 inet static auto vlan111 auto vlan222 auto vlan333 auto vlan444 auto br0 auto br1 auto br2 # LAN iface vlan111 inet static vlan_raw_device eth0 # WLAN iface vlan222 inet static vlan_raw_device eth0 # ADSL Modem iface vlan333 inet static vlan_raw_device eth1 # Internet iface vlan444 inet static vlan_raw_device eth0 # LAN bridge iface br0 inet static address 192.168.0.1 netmask 255.255.255.0 bridge_ports eth0.111 bridge_stp on # Internet bridge iface br1 inet static address x.x.x.x netmask x.x.x.x gateway x.x.x.x bridge_ports eth1.333 eth0.444 bridge_stp on post-up iptables -t nat -A POSTROUTING -o br1 -j MASQUERADE pre-down iptables -t nat -D POSTROUTING -o br1 -j MASQUERADE # WLAN bridge iface br2 inet static address 192.168.1.1 netmask 255.255.255.0 bridge_ports eth0.222 bridge_stp on Sysctl: net.ipv4.conf.default.forwarding=1

Read the article
Including email, IMs, configs, etc. in documentation or notes

- by Jason Antman

The shop I work in is pretty laid-back. We're on a documentation kick, only because historically we've been very bad with it. We do a lot of our brainstorming in face-to-face meetings, and also do a lot of communication via IM in addition to email. While I'm usually pretty good about documentation and keeping copious lab notes, I just finished a build of a host and spent hours searching through IMs, emails, files on my workstation, etc. to pull out anything I missed in my lab notes, which formed a large amount of the basis for the internal documentation. Does anyone have any thoughts on, aside from manually saving things to a project directory, managing various data sources (especially email and IM) and tracking them on project basis? Ideally, I'd like an easy way to put copies of emails, IM logs, etc. into a project-specific directory on my workstation and then just have a cron job that syncs that up with a shared folder. This isn't really a candidate for anything more advanced, as the bulk of the data will be copies of configs, code, etc. Here are the big restrictions: Email is via a centralized Zimbra install, so nothing can happen server-side. My workstation is Linux. Aside from writing Pidgin and Thunderbird plugins that let me tag chats and emails as belonging to a project, and then copy them to the appropriate place... any thoughts? Suggestions? Thanks, Jason

Read the article
Need Help getting perl module DBD::mysql installed for bugzilla on RedHat.

- by Alos Diallo

Hi everyone I am having some issues getting Bugzilla setup, I have the software on the server and am trying to get the pre-rec's setup. I am using RedHat 4.1.2-42. I have all of the required perl modules save one:DBD::mysql When I try: sudo perl install-module.pl DBD::mysql I get the following response(this is only an excerpt): rm -f blib/arch/auto/DBD/mysql/mysql.so LD_RUN_PATH="/usr/lib64/mysql:/usr/lib64:/lib64" /usr/bin/perl myld gcc -shared -O2 -g -pipe -Wall -Wp,-D_FORTIFY_SOURCE=2 -fexceptions -fstack-protector --param=ssp-buffer-size=4 -m64 -mtune=generic dbdimp.o mysql.o -o blib/arch/auto/DBD/mysql/mysql.so \ -L/usr/lib64/mysql -lmysqlclient -lz -lcrypt -lnsl -lm -L/usr/lib64 -lssl -lcrypto \ /usr/bin/ld: skipping incompatible /usr/lib/libssl.so when searching for -lssl /usr/bin/ld: skipping incompatible /usr/lib/libssl.a when searching for -lssl /usr/bin/ld: cannot find -lssl collect2: ld returned 1 exit status make: * [blib/arch/auto/DBD/mysql/mysql.so] Error 1 /usr/bin/make -- NOT OK Running make test Can't test without successful make Running make install make had returned bad status, install seems impossible I then tried the following: CFLAGS="-I/usr/lib64/mysql:/usr/lib64:/lib64" perl install-module.pl DBD::mysql I get the same result. I have also tried to install it using CPAN but also get the same result. Right now I have DBD-mysql v3.0007 but need (v4.00) Also when I try to install open ssl it says I have the latest version. Does anyone know what I have to do to get this to work? Any help would be greatly appreciated. Thank you

Read the article
Radeon 6950 - Garbling of text and graphics in certain Windows only

- by Greg

This morning I noticed the text in Gmail (in Firefox 4) looked a little funny (kind of thin, maybe some color fringing). I went to work and thought it might be some ClearType issue or something with the way Direct way that FF4 draws to the screen. When I came back from work (I left the computer on), the problem was much worse - way beyond ClearType nit-picking. The text was barely readable. I opened Chrome and there was no such problem. It seems like only Windows that use hardware acceleration are garbled, and ones that use GDI are not. But, I fired up Dragon Age and didn't notice any problems (I only really looked at the main menu though). Here is a link to a screen shot that illustrates the problem. Notice how the Windows Live Mesh window is completely unreadable, the text in Firefox 4 (left) is pretty bad, while Chrome, the Windows Control Panel, and the task bar are perfectly fine. The fact that the problem shows up in screen shots and that it only happens in certain Windows makes me confident that the problem cannot be with the monitor or DVI cable. I am using the AMD Radeon drivers from 4/27/11. The card I have (MSI Frozr II) came with a slight overclock (810Mhz) out of the box, but it looks like when I'm on the Windows desktop it's not running at full clock (CCC reports 450Mhz). Still, I underclocked it to the stock reference clock (800Mhz) and it made no difference. The idle temperature according to Afterburner is 42-44 Celsius, which seems a tad high but not enough to cause a problem - it's cold to the touch if I open up the machine. What the heck could be causing this? The problem varies in intensity. As we speak I'm in Firefox and things look better than they did earlier - it'll probably get worse again soon. Radeon 6950 (MSI Frozr II), Seasonic X 560, Core i5 2500K at stock clockspeeds, 16GB RAM, Asus P8P67 M Pro

Read the article
Cannot write samba shares

- by Batsu

Running samba 3.5 on Red Hat Enterprise 6.1 I'm having issues sharing two folders. Here is the output of testparm: [global] workgroup = DOMAINNAME server string = Samba Server Version %v interfaces = lo, eth1 bind interfaces only = Yes map to guest = Bad User log file = /var/log/samba/log.%m max log size = 50 idmap uid = 16777216-33554431 idmap gid = 16777216-33554431 hosts allow = 10.50.183.48, 10.50.184.41, 10.50.184.199, 10.50.183.160, 127.0.0.1 hosts deny = 0.0.0.0/0 cups options = raw [test] comment = test folder path = /usr/local/samba valid users = claudio write list = claudio force user = claudio read only = No create mask = 0775 directory mask = 0775 [test2] comment = another test path = /home/claudio/tst valid users = claudio write list = claudio force user = claudio read only = No create mask = 0775 From the Windows XP machine I'm connecting from I'm able to read test but not write, while for test2 I can't even access the folder (though I can see it listed). ls -l /usr/local ... drwxrwxrwx. 2 claudio claudio 4096 Dec 3 10:39 samba ... ls -l /user/local/samba total 32 -rwxrwxrwx. 1 claudio claudio 9 Nov 29 16:26 asd.txt -rwxrwxrwx. 1 claudio claudio 728 Dec 3 10:16 out.txt ... ls -l /home/claudio/ ... drwxrwxr-x. 2 claudio claudio 4096 Dec 3 09:57 tst ... ls -l /home/claudio/tst total 4 -rw-rw-r--. 1 claudio claudio 4 Dec 3 09:57 asd.txt Any suggestion?

Read the article
Diagnosing Logon Audit Failure event log entries

- by Scott Mitchell

I help a client manage a website that is run on a dedicated web server at a hosting company. Recently, we noticed that over the last two weeks there have been tens of thousands of Audit Failure entries in the Security Event Log with Task Category of Logon - these have been coming in about every two seconds, but interesting stopped altogether as of two days ago. In general, the event description looks like the following: An account failed to log on. Subject: Security ID: SYSTEM Account Name: ...The Hosting Account... Account Domain: ...The Domain... Logon ID: 0x3e7 Logon Type: 10 Account For Which Logon Failed: Security ID: NULL SID Account Name: david Account Domain: ...The Domain... Failure Information: Failure Reason: Unknown user name or bad password. Status: 0xc000006d Sub Status: 0xc0000064 Process Information: Caller Process ID: 0x154c Caller Process Name: C:\Windows\System32\winlogon.exe Network Information: Workstation Name: ...The Domain... Source Network Address: 173.231.24.18 Source Port: 1605 The value in the Account Name field differs. Above you see "david" but there are ones with "john", "console", "sys", and even ones like "support83423" and whatnot. The Logon Type field indicates that the logon attempt was a remote interactive attempt via Terminal Services or Remote Desktop. My presumption is that these are some brute force attacks attempting to guess username/password combinations in order to log into our dedicated server. Are these presumptions correct? Are these types of attacks pretty common? Is there a way to help stop these types of attacks? We need to be able to access the desktop via Remote Desktop so simply turning off that service is not feasible. Thanks

Read the article
Timeout option not working on efi windows 7/windows8 dual boot machine

- by Guenter

I hav a gigbyte GA-Z77m-D3h mobo and installed Windows 8 Pro and Windows 7 Ultimate on two SSDs (in that order) in EFI mode. Now when I start my computer, I get the windows boot menu (text mode) with the two OSses to choose, but I have to manually press RETURN to have the computer boot into the Win OS. Even if I wait an hour, no default action takes place. Using bcdedit (from either of the OSses) I can successfully change the time out value, and it shows up in the bcdedit (no params) output. But it doesn't fire ... Here is my current BCDEdit output (headers are in German, but values should be readable): Windows-Start-Manager --------------------- Bezeichner {bootmgr} device partition=O: path \EFI\Microsoft\Boot\bootmgfw.efi description Windows Boot Manager locale de-DE inherit {globalsettings} integrityservices Enable default {default} resumeobject {5ad2802c-c60a-11e2-acdb-80331c501b11} displayorder {default} {current} {5ad2802a-c60a-11e2-acdb-80331c501b11} {5ad28028-c60a-11e2-acdb-80331c501b11} {5ad28029-c60a-11e2-acdb-80331c501b11} toolsdisplayorder {memdiag} timeout 5 displaybootmenu Yes Windows-Startladeprogramm ------------------------- Bezeichner {default} device partition=W: path \Windows\system32\winload.efi description Windows 7 locale de-DE inherit {bootloadersettings} recoverysequence {5ad2802e-c60a-11e2-acdb-80331c501b11} recoveryenabled Yes osdevice partition=W: systemroot \Windows resumeobject {5ad2802c-c60a-11e2-acdb-80331c501b11} nx OptIn Windows-Startladeprogramm ------------------------- Bezeichner {current} device partition=C: path \Windows\system32\winload.efi description Windows 8 locale de-DE inherit {bootloadersettings} recoverysequence {5ad28033-c60a-11e2-acdb-80331c501b11} integrityservices Enable recoveryenabled Yes isolatedcontext Yes allowedinmemorysettings 0x15000075 osdevice partition=C: systemroot \Windows resumeobject {5ad28031-c60a-11e2-acdb-80331c501b11} nx OptIn bootmenupolicy Standard hypervisorlaunchtype Auto (this output is from Win8; the Win7 looks nearly identical) If maybe the problem comes from a bad EFI Windows boot manager installation, can this be fixed without loosing my windows installations?

Read the article
Authority Information Access local path being ignored

- by Kevin

I have a CA set up in Server 2008 R2, and generally it is working, but I can't control the local path/filename it writes its own certificate to for the Authority Information Access publishing. Here's a screen shot of the dialog I'm trying to set this on: From these settings I would expect to get the file: C:\Windows\system32\CertSrv\CertEnroll\DAMNIT.crt But instead I get: C:\Windows\system32\CertSrv\CertEnroll\SERVER.domain.com_My Issuing Authority(1).crt Of course, the actual change shown wouldn't be very useful, but it's illustrative; no matter what path/filename I use, it always lands up in the same place and with the same name. I actually wanted to change the name from <ServerDNSName>_<CaName><CertificateName>.crt to <CaName><CertificateName>.crt, since the latter corresponds to the HTTP URL whereas the former does not. Admittedly, I haven't set up many CAs so perhaps I'm just deluded as to what this dialog is supposed to be setting, but if so this is notoriously bad UI design. (Incidentally, I have a couple other complaints with the same dialog.) What's going on here and is there some way to get the filename pattern I want?

Read the article
Why does running "$ sudo chmod -R 664 . " cause me to get access denied on all affected directories?

- by Codemonkey

I have a project folder which has messy permissions on all files. I've had the bad tendency of setting everything to octal permissions 777 because it solved all non security related issues. Then FTP uploads, files created by text editors etc. has their own set of permissions making everything a mess. I've decided to take myself together and start using the permissions the way they were meant to be used. I figured 664 was a good default for all my files and folders, and I'd just remove permissions for others on private files, and add +x for executable files. The second I changed my project folder to 664 however: $ sudo chmod -R 664 . $ ls ls: cannot open directory .: Permission denied Which makes no sense to me. I have read/write permissions, and I'm the owner of the project folder. The leftmost part of ls -l in my project folder looks like this: -rw-rw-r-- 1 codemonkey codemonkey ... drw-rw-r-- 5 codemonkey codemonkey ... -rw-rw-r-- 1 codemonkey codemonkey ... -rw-rw-r-- 1 codemonkey codemonkey ... drw-rw-r-- 3 codemonkey codemonkey ... -rw-rw-r-- 1 codemonkey codemonkey ... -rw-rw-r-- 1 codemonkey codemonkey ... -rw-rw-r-- 1 codemonkey codemonkey ... drw-rw-r-- 4 codemonkey codemonkey ... drw-rw-r-- 5 codemonkey codemonkey ... I assume this has something to do with the permissions on the directories, but what?

Read the article
What is the sysadmin's dream network printer? 6-8k pg/mo. Xerox, OkiData, Lexmark and HP are all fail

- by Jacob

How do I find out what printer brand and/or type doesn't suck? This information is hard to find and manufacturer's websites won't reveal any issues with certain printers. After 10 years of dealing with network shared printers, I can't say that I have been impressed with any of the printer brands I've seen. Brother's little laser MFPs have been close to ideal for low volume, but that is it, period. OkiData, Lexmark, HP, Xerox solid ink printers, they all sucked in one way or another. Currently I'm looking to replace a Xerox ColorQube 8570 because it fails to print on a regular basis. Sometimes it doesn't even boot VxWorks fully - it just hangs at 2% or whatever. I've used Xerox 8860MFPs and they sucked just as bad. I won't talk about ink jets here, that's most likely not what I'm looking for. We currently spend about $4k on paper and ink per year for this printer at up to 6-8k pages per month, letter, mostly black and white, low color usage. I want the printer to feed paper correctly, not crash and burn when a PDF isn't according to its taste (my favorite Xerox problem here) and with decent drivers for Windows and OS X. Print quality is not of the utmost importance but paper does get sent to customers.

Read the article
Install VirtualBox on Ubuntu 12.04.1 (on [Samsung] Chromebook)

- by iphonedev7

I have dual booted Ubuntu Linux 12.04.1 LTS on my Samsung Series 5 ChromeBook, and am trying to run/install Oracle VirtualBox (from the generic .run file downloaded from their website). However, every time I try to run it (as root from the command line), it gives me the following error occurs: Please install the build and header files for your current Linux kernel. The current kernel version is 3.4.0 Problems were found which would prevent VirtualBox from installing. I have tried the version from the Software Center, as well as the command line installation, both of which gave me errors based on my linux-headers/linux-kernel/linux-[kernel]-image. Here's an error I keep getting (on the command line): First Installation: checking all kernels... It is likely that 3.4.0 belongs to a chroot's host Building only for 3.5.0-18-generic Building initial module for 3.5.0-18-generic ERROR (dkms apport): kernel package linux-headers-3.5.0-18-generic is not supported Error! Bad return status for module build on kernel: 3.5.0-18-generic (x86_64) Consult /var/lib/dkms/virtualbox/4.1.12/build/make.log for more information. Setting up virtualbox-qt (4.1.12-dfsg-2ubuntu0.2) ... Processing triggers for libc-bin ... ldconfig deferred processing now taking place ...And one of the more cryptic errors I get when trying to start any Virtual Machine: Result Code: NS_ERROR_FAILURE (0x80004005) Component: Machine Interface: IMachine {5eaa9319-62fc-4b0a-843c-0cb1940f8a91}

Read the article
Radeon 6950 - Garbling of text and graphics in certain Windows only

- by Greg

This morning I noticed the text in Gmail (in Firefox 4) looked a little funny (kind of thin, maybe some color fringing). I went to work and thought it might be some ClearType issue or something with the way Direct way that FF4 draws to the screen. When I came back from work (I left the computer on), the problem was much worse - way beyond ClearType nit-picking. The text was barely readable. I opened Chrome and there was no such problem. It seems like only Windows that use hardware acceleration are garbled, and ones that use GDI are not. But, I fired up Dragon Age and didn't notice any problems (I only really looked at the main menu though). Here is a link to a screen shot that illustrates the problem. Notice how the Windows Live Mesh window is completely unreadable, the text in Firefox 4 (left) is pretty bad, while Chrome, the Windows Control Panel, and the task bar are perfectly fine. The fact that the problem shows up in screen shots and that it only happens in certain Windows makes me confident that the problem cannot be with the monitor or DVI cable. I am using the AMD Radeon drivers from 4/27/11. The card I have (MSI Frozr II) came with a slight overclock (810Mhz) out of the box, but it looks like when I'm on the Windows desktop it's not running at full clock (CCC reports 450Mhz). Still, I underclocked it to the stock reference clock (800Mhz) and it made no difference. The idle temperature according to Afterburner is 42-44 Celsius, which seems a tad high but not enough to cause a problem - it's cold to the touch if I open up the machine. What the heck could be causing this? The problem varies in intensity. As we speak I'm in Firefox and things look better than they did earlier - it'll probably get worse again soon. Radeon 6950 (MSI Frozr II), Seasonic X 560, Core i5 2500K at stock clockspeeds, 16GB RAM, Asus P8P67 M Pro

Read the article
VMware ESXi 4.1 snapshot of server 2008R2 machine generates 2 indentical snapshots

- by Peter

I have 2 VMs that are failing to get veeam backups, and it appears that the culprit is vmware snapshots. We are running Vsphere ESXi 4.1 build 320092, we have multiple server 2008R2 machines that take snapshots fine, but when with these two VMs when I take a snapshot I get 2 identical snapshots a few seconds apart. The snapshot manager only shows 1 snapshot, but there are 2 files 1 number off, that are identical sizes. There is only one disk on each VM, so that isn't the problem. Has anyone seen this behavior before and know how to fix it? Here are the files after a bad snapshot VM-XXX-000001-ctk.vmdk VM-XXX-000001-delta.vmdk VM-XXX-000001.vmdk VM-XXX-000002-ctk.vmdk VM-XXX-000002-delta.vmdk VM-XXX-000002.vmdk VM-XXX-2a659dbf.hlog VM-XXX-2a659dbf.vswp VM-XXX-Snapshot286.vmsn VM-XXX-aux.xml VM-XXX-ctk.vmdk VM-XXX-flat.vmdk VM-XXX-vss_manifests286.zip VM-XXX.nvram VM-XXX.vmdk VM-XXX.vmsd VM-XXX.vmx VM-XXX.vmxf vmware-20.log vmware-21.log vmware-22.log vmware-23.log vmware-24.log vmware-25.log vmware.log VM-XXX-000001.vmdk and VM-XXX-000002.vmdk are the exact same size.

Read the article
Multiple *NIX Accounts with Identical UID

- by Tim

I am curious whether there is a standard expected behavior and whether it is considered bad practice when creating more than one account on Linux/Unix that have the same UID. I've done some testing on RHEL5 with this and it behaved as I expected, but I don't know if I'm tempting fate using this trick. As an example, let's say I have two accounts with the same IDs: a1:$1$4zIl1:5000:5000::/home/a1:/bin/bash a2:$1$bmh92:5000:5000::/home/a2:/bin/bash What this means is: I can log in to each account using its own password. Files I create will have the same UID. Tools such as "ls -l" will list the UID as the first entry in the file (a1 in this case). I avoid any permissions or ownership problems between the two accounts because they are really the same user. I get login auditing for each account, so I have better granularity into tracking what is happening on the system. So my questions are: Is this ability designed or is it just the way it happens to work? Is this going to be consistent across *nix variants? Is this accepted practice? Are there unintended consequences to this practice? Note, the idea here is to use this for system accounts and not normal user accounts.

Read the article
Can't find gnutls ibrary when executing rpmbuild under non-root

- by Rilindo

I am trying to build ntgs from the latest source, using the .spec from rpmforge - as non-root via rpmbuild. During the compile, it fails at this step: checking for GNUTLS... no configure: error: ntfsprogs crypto code requires the gnutls library. error: Bad exit status from /var/tmp/rpm-tmp.78913 (%build) However, I can compile it successfully outside of rpmbuild. So it sounds like it just the matter of library being seen during the build. However, I can confirm that rpmbuild can see the library that gnutls resides: [foo@bar ~]$ rpmbuild -E '%{_libdir}' rpmbuild/SPECS/ntfsprogs.spec /usr/lib Library location: [foo@bar ntfs-3g_ntfsprogs-2012.1.15]$ /sbin/ldconfig -p | grep -i gnutls libgnutls.so.13 (libc6) => /usr/lib/libgnutls.so.13 libgnutls.so (libc6) => /usr/lib/libgnutls.so libgnutls-openssl.so.13 (libc6) => /usr/lib/libgnutls-openssl.so.13 libgnutls-openssl.so (libc6) => /usr/lib/libgnutls-openssl.so libgnutls-extra.so.13 (libc6) => /usr/lib/libgnutls-extra.so.13 libgnutls-extra.so (libc6) => /usr/lib/libgnutls-extra.so What would cause the problem of the library not being seen when you build a RPM? EDIT: Oh yeah, I am running Centos 5.5.

Read the article
VPN messes up DNS resolution

- by user124114

After connecting with the Kerio VPN client (OS X Leopard) to a server, the internet (~web browsing) stopped working for the client. After poking around, the issue seems to be bad DNS server (i.e., entering IPs directly works). After disconnecting from the VPN, the invalid DNS server disappears from scutil --dns and all's well again. Now, I don't understand why OS X on the client even changes the DNS settings -- internet should be routed through a different interface, through the default gateway, not through the VPN. Questions: By what mechanism does connecting the VPN client change the "default" DNS server? How can I stop the VPN client from changing routing/DNS rules? Where is this stuff stored/modified? Before VPN: $ scutil --dns DNS configuration resolver #1 nameserver[0] : 10.66.77.1 # <---- default gateway = home router; all good order : 200000 resolver #2 domain : local options : mdns timeout : 2 order : 300000 ... VPN connected: $ scutil --dns DNS configuration resolver #1 nameserver[0] : 192.168.1.1 # <--- rubbish nameserver[1] : 192.168.2.1 order : 200000 resolver #2 domain : local options : mdns timeout : 2 order : 300000 ... The VPN doesn't appear among $ networksetup -listallnetworkservices.

Read the article
WRT54GL Tomato Router in Client wireless mode to an iPhone Personal Hotspot

- by Gordo

I am trying to connect a router with Tomato firmware to an iPhone 4. The goal is to connect to the Personal Hotspot in Client Wireless mode. This should allow wired and wireless users to connect to the router rather then the iPhone. In theory this should be possible but I am having difficulty. Router Linksys WRT54GL Tomato 1.28.1816 firmware iPhone iPhone 4 iOS 5.1 (9B176) Carrier Rogers Wireless Personal Hotspot works with other devices, wifi/bluetooth/usb iPhone Personal Hotspot settings Mode: B/G Security: WPA or WPA2 Personal Encryption: AES Router IP: 172.20.10.1 Subnet: 172.20.10.0 Min IP: 172.20.10.2 Max IP: 172.20.10.14 maximum number of wireless tethered hosts is 5 I have followed the directions here: http://www.wi-fiplanet.com/tutorials/article.php/3810281 Ensured that the router subnet does not 'collide' with the iPhone subnet. Here is the configuration of the Tomato 'Basic - Network - Wireless' section: http://i.stack.imgur.com/pbmTB.png I have tried several variations of this configuration, but nothing seems to work. NOTE: I have successfully connected to my own wifi network in Wireless Client mode, so I am confident that there are no bad cables or other hardware issues. I would prefer to use Tomato, but DD-WRT maybe my only other option. Thanks!

Read the article
How do you use VIM to edit tabular data (tables)? Specifically, BIND (named) DNS db files.

- by Richard Bronosky

I'm usually a purist when it comes to vimming. I don't like remapping keys, or learning to rely on a bunch of plugins. I like to feel just as powerful on foreign boxen as I do on my own dev box. I do, however, believe in syntax files. Even though the solution may not be a syntax file (bindzone.vim is what I use), I want it bad enough to do whatever. I regularly view or edit tab (or comma, but that would be a bonus) delimited data. I hate having to set my tabstop to some ridiculous number in order to have everything line up. Example: The BIND zone files are ~40+,6,2,5,15+. So, even though I could view them on a single screen, if I set ts=40, I cannot. I have been searching for a "dynamic tab size" solution for years, but no luck. I hate that my only good way of editing or even visualizing tabular data is to scp it to my work station and open it in Open Office. There has to be a better way.

Read the article

< Previous Page | 240 241 242 243 244 245 246 247 248 249 250 251 | Next Page >