Search Results

Search found 28582 results on 1144 pages for 'message loop'.

Page 245/1144 | < Previous Page | 241 242 243 244 245 246 247 248 249 250 251 252  | Next Page >

  • tap interfaces always disabled in linux bridge

    - by Dani Camps
    I have a physical interface eth0, and I want to create two virtual interfaces and bridge them with eth0. For this purpose I do: #Create the virtual interfaces tunctl -t tap0 tunctl -t tap1 ifconfig tap0 up ifconfig tap1 up #Create the bridge brctl addbr br0 brctl stp br0 off brctl addif br0 eth0 brctl addif br0 tap0 brctl addif br0 tap1 #Turning up the bridge ifconfig br0 up However my problem if that the tap interfaces always appear disabled in the bridge, and no traffic flows to them. $brctl show br0 bridge name bridge id STP enabled interfaces br0 8000.080027cabeba no eth2 tap0 tap1 $brctl showstp br0 br0 bridge id 8000.080027cabeba designated root 8000.080027cabeba root port 0 path cost 0 max age 20.00 bridge max age 20.00 hello time 2.00 bridge hello time 2.00 forward delay 15.00 bridge forward delay 15.00 ageing time 300.01 hello timer 0.00 tcn timer 0.00 topology change timer 0.00 gc timer 298.42 flags eth2 (1) port id 8001 state forwarding designated root 8000.080027cabeba path cost 4 designated bridge 8000.080027cabeba message age timer 0.00 designated port 8001 forward delay timer 12.97 designated cost 0 hold timer 1.24 flags tap0 (2) port id 8002 state disabled designated root 8000.080027cabeba path cost 100 designated bridge 8000.080027cabeba message age timer 0.00 designated port 8002 forward delay timer 0.00 designated cost 0 hold timer 0.00 flags tap1 (3) port id 8003 state disabled designated root 8000.080027cabeba path cost 100 designated bridge 8000.080027cabeba message age timer 0.00 designated port 8003 forward delay timer 0.00 designated cost 0 hold timer 0.00 flags Is there any way to set the tap interfaces in forwarding state? I do not understand why they are not because STP is disabled. Cheers Daniel

    Read the article

  • SQL Server 2008 Cluster Installation - First network name always fails

    - by boflynn
    I'm testing failover clustering in Windows Server 2008 to host a SQL Server 2008 installation using this installation guide. My base cluster is installed and working properly, as well as clustering the DTC service. However, when it comes time to install SQL Server, my first attempt at installation always fails with the same message and seems to "taint" the network name. For example, with my previous cluster attempt, I was installing SQL Server as VSQL. After approximately 15 attempts of installation and trying to resolve the errors, e.g. changing domain accounts for SQL, setting SPNs, etc., I typoed the network name as VQSL and the installation worked. Similarly on my current cluster, I tried installing with the SQL service named PROD-C1-DB and got the same errors as last time until I tried changing the name to anything else, e.g. PROD-C1-DB1, SQL, TEST, etc., at which point the install works. It will even install to VSQL now. While testing, my install routine was: Run setup.exe from patched media, selecting appropriate options After the install fails, I'd chose "Remove node from a SQL Server failover cluster" and remove the single, failed, node Attempt to diagnose problem, inspect event logs, etc. Delete the computer account that was created for the SQL Service from Active Directory Delete the MSSQL10.MSSQLSERVER folder from the shared data drive The error message I receive from the SQL Server installer is: The following error has occurred: The cluster resource 'SQL Server' could not be brought online. Error: The group or resource is not in the correct state to perform the requested operation. (Exception from HRESULT: 0x8007139F) Along with hundreds of the following errors in the Application event log: [sqsrvres] checkODBCConnectError: sqlstate = 28000; native error = 4818; message = [Microsoft][SQL Server Native Client 10.0][SQL Server]Login failed for user 'NT AUTHORITY\ANONYMOUS LOGON'. System configuration notes: Windows Server 2008 Enterprise Edition x64 SQL Server 2008 Enterprise Edition x64 using slipstreamed SP1+CU1 media Dell PowerEdge servers Fibre attached storage

    Read the article

  • Error while installing boost_1_54

    - by Farhat
    On trying to install boost I get this error during configuration checks. Googling did not give any pointers. [root@heracles boost_1_54_0]# ./b2 install Performing configuration checks - 32-bit : no (cached) - 64-bit : yes (cached) - arm : no (cached) - mips1 : no (cached) - power : no (cached) - sparc : no (cached) - x86 : yes (cached) error: No best alternative for libs/coroutine/build/allocator_sources next alternative: required properties: <link>static <target-os>windows <threading>multi not matched next alternative: required properties: <link>static <segmented-stacks>on <threading>multi not matched next alternative: required properties: <link>static <threading>multi not matched - has_icu builds : no (cached) warning: Graph library does not contain MPI-based parallel components. note: to enable them, add "using mpi ;" to your user-config.jam - zlib : yes (cached) - iconv (libc) : yes (cached) - icu : no (cached) - icu (lib64) : no (cached) - compiler-supports-ssse3 : yes (cached) - compiler-supports-avx2 : no (cached) - gcc visibility : yes (cached) - long double support : yes (cached) warning: skipping optional Message Passing Interface (MPI) library. note: to enable MPI support, add "using mpi ;" to user-config.jam. note: to suppress this message, pass "--without-mpi" to bjam. note: otherwise, you can safely ignore this message. error: No best alternative for libs/coroutine/build/allocator_sources next alternative: required properties: <link>static <target-os>windows <threading>multi not matched next alternative: required properties: <link>static <segmented-stacks>on <threading>multi not matched next alternative: required properties: <link>static <threading>multi not matched - zlib : yes (cached) How can the alternative for allocator sources be located? Thanks.

    Read the article

  • Mail to Mailenable group sometimes bounces back because it cannot find one of the group members

    - by Stanley
    I am using MailEnable Enterprise Edition 6.53. On one of my PostOffices I have a group address set up with 5 members in the group. Under normal circumstances when someone sends a mail to this group then the mail gets successfully forwarded to all 5 members in the group. However, every now and then when a recipient sends to the group they get a bounce back message from us that the mail could not be delivered because one of the user's addresses was not found on the server. This could happen for any one of the 5 users in the group. The error message looks like: Message could not be delivered. Error was: The email address is not available on this system The following recipient(s) could not be reached: [SF:mydomain.com/my_username] What could be causing this and how do I fix it? Obviously the mailbox DOES exist as, under normal circumstances, when someone mails the group the mail gets delivered successfully and forwarded to all group members. All the mailboxes most definitely DO exist on the system. EDIT: I have done more investigation and I see an error in Windows Event Viewer: MailEnable Database Provider error: 0 FAILURE: (SQLDriverConnect), Module: MEIMAPS.exe; Error: [Microsoft][ODBC SQL Server Driver]Timeout expired This seems to be related to http://forum.mailenable.com/viewtopic.php?p=53157 and http://www.mailenable.com/kb/content/view.asp?ID=ME020535 but the setups in these links use MySQL as a database whereas we use SQL Server. Maybe this shines some new light on the problem?

    Read the article

  • NTDS Replication Warning (Event ID 2089)

    - by Chris_K
    I have a simple little network with 3 AD servers in 2 sites. Site A has Win2k3 SP2 and Win2k SP4 servers, site B has a single Win2k3 SP2 server. All have been in place for at least 3 years now. Just last week I started getting Event 2089 "not backed up" warnings (example below) on both of the win2k3 servers. I understand what the message means, no need to send me links to the technet article explaining it. I'll improve my backups. What I'm more curious about is why did I just start getting this message now? Why haven't I been getting it for the past 3 years?!? Perhaps this is related: I recently decommissioned a few other sites and AD controllers (there used to be 3 more sites, each with their own controller). Don't worry, I did proper DCpromo exercises and made sure we didn't lose anything. But would shutting those down possibly be related to why I get this error now? This won't keep me awake at night but I am curious as to what changed... Event Type: Warning Event Source: NTDS Replication Event Category: Backup Event ID: 2089 Date: 3/28/2010 Time: 9:25:27 AM User: NT AUTHORITY\ANONYMOUS LOGON Computer: RedactedName Description: This directory partition has not been backed up since at least the following number of days. Directory partition: DC=MyDomain,DC=com 'Backup latency interval' (days): 30 It is recommended that you take a backup as often as possible to recover from accidental loss of data. However if you haven't taken a backup since at least the 'backup latency interval' number of days, this message will be logged every day until a backup is taken. You can take a backup of any replica that holds this partition. By default the 'Backup latency interval' is set to half the 'Tombstone Lifetime Interval'. If you want to change the default 'Backup latency interval', you could do so by adding the following registry key. 'Backup latency interval' (days) registry key: System\CurrentControlSet\Services\NTDS\Parameters\Backup Latency Threshold (days) For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp.

    Read the article

  • Tracking down source of duplicate email messages in Outlook / Exchange environment

    - by Ken Pespisa
    I have a few users, who are also Blackberry users, that occasionally have duplicate emails generated from their "mailbox". I put mailbox in quotes because I'm not exactly sure where the duplicates are created. One of these users is in non-cached mode, and the other is in cached mode, and both experience the problem. In fact, the non-cached mode user was originally experiencing the problem while in cached mode, and I made the switch a few weeks ago to attempt to solve the problem. Today I discovered the issue still exists. I'm not sure if the fact that they are blackberry users could be causing the problem at all. I don't see how, but felt I should mention it anyway. Does anyone have ideas on how I might begin to troubleshoot this? I can see in the non-cached user's mailbox "Sent Items" that the message was sent only once. I confirmed the message does not state that there was a conflict and in fact that makes sense because they are in non-cached mode. On the server, we have a mail journaling feature turned on for our third-party mail archiving system, and I can see that that system sees two sent messages. And likewise, the recipient does in fact have two messages in their inbox with consecutive message IDs ([email protected]) and ([email protected]). It would seem to me that the duplicates are generated on the client, but is there a way to tell for sure?

    Read the article

  • change owner/uid of mount point upon mount

    - by Shiplu
    The scenario is like this. Bob has a computer. It crashed. Now he only has the hdd. The hdd is in ext3 format. He go to his office and told the sys admin John to mount this hdd and put the mount point in his home directory. John used the following fstab entries. # Bobs harddisk /media/TAPE4/Bobs-hdd.img /home/bob/myhdd/windows ntfs ro,loop,offset=32256 0 0 /media/TAPE4/Bobs-hdd.img /home/bob/myhdd/linux ext3 ro,loop,offset=14048810496 0 0 /media/TAPE4/Bobs-hdd.img /home/bob/myhdd/extra ntfs ro,loop,offset=28015335936 0 0 Bob was happy. He could access his old extra and windows. Specially the Documents and Settings in windows was helpful for him. But he found a problem. He is a web developer and all his websites are in linux/home/bob/public_html directory. When he tried to access that public_html directory he got permission_denied. He executed ls -lh he saw this. drwxr-xr-x 2 john john 4.0K Nov 9 2011 Desktop drwxr-xr-x 3 john john 4.0K Aug 12 2011 Documents drwxr-xr-x 3 john john 4.0K Aug 21 2011 public_html He contacted John thinking he might be mistakenly did this. But John couldn't find a way why this happend? Then one thing came into his mind file system hardly store username. They store uids. So he executed ls -ln drwxr-xr-x 2 1000 1000 4096 Nov 9 2011 Desktop drwxr-xr-x 3 1000 1000 4096 Aug 12 2011 Documents drwxr-xr-x 3 1000 1000 4096 Aug 21 2011 public_html John thinks 1000 is the first uid on a linux system. As he is the admin of the current system. He created his account first. so Johns uid was 1000. Bob also setup his private system and crated his account first. So Bobs uid was 1000 too. So thats an expected behavior. But problem remains. How can Bob access those websites in public_html?

    Read the article

  • Redirect subdomain to hidden folder using mod_rewrite

    - by radious
    Hello! I want to keep my blog in subfolder domain_com/htdocs/blog and access it using blog.domain.com. I can obtain it using apache's mod_rewrite: RewriteEngine On RewriteBase / RewriteCond %{HTTP_HOST} ^blog\.domain\.com RewriteCond %{HTTP_HOST} !^/blog RewriteRule ^(.*)$ /blog/$1 [L] But I also want to redirect hxxp://domain.com/blog to hxxp://blog.domain.com (simply because I want to hide it from users). Simple redirection like: RewriteCond %{HTTP_HOST} ^wojtyniak\.com$ RewriteRule %{REQUEST_URI} ^/foo RewriteRule ^(.*)$ http://foo.wojtyniak.com [L,R=301] causes redirection loop. Is there any way to make such a redirection without loop? Big thanks! PS. Sorry for those hxxp thing, but serverfault thinks these are link and doesn't allow me to post more than one.

    Read the article

  • Samba between Ubuntu server 10.10 and Windows Vista, Windows 7

    - by chepukha
    I have a linux box running Linux server ubuntu 10.10. I have installed Samba on this linux box and want to share files with my laptops which run Windows Vista home and Windows 7 home. I have been struggling with the setup for almost a month but couldn't get it right. If I try to access share folder from Windows Vista, I get message "Windows cannot access \\server_ip_address". Error code: 0x80070035. The network path was not found. If I access from Windows 7, then after entering password to login I can see the list of share folders on Linux box. But if I click on a share folder, I get the same error message as above. Tail /var/log/samba/log.windows7-pc I got the following message: [2011/03/16 00:17:41.427238, 0] smbd/service.c:988(make_connection_snum) canonicalize_connect_path failed for service sharemedia, path /root/sharemedia Here is my setting in smb.conf [global] share modes = yes netbios name = Samba workgroup = WORKGROUP wins support = yes encrypt passwords = true [sharemedia] comment = Tesing sharing using Samba path=/root/sharemedia/ public = yes valid users = samba_usr_name ; make sure all files are sensible permissions create mask = 0660 force create mask = 0660 directory mask = 2770 force directory mask = 2770 directory security mask = 0000 ; Normal share parameters read only = no browseable = yes writable = yes guest ok = no

    Read the article

  • Sporadic email delivery to one user

    - by minamhere
    I have a user that occasionally does not receive emails from outside our organization. It does not seem to matter whether the other person is replying to an initial email or sending a new message. I have checked the Exchange System Manager and there is no record of the sender at all during this time period. No record of the message getting captured by the spam software (GFI Mail Essentials). The sender does not receive an NDR or any other indication that the message didn't arrive. It seems to me that these messages are not even getting to our servers at all. But, this is only impacting one user(that I am aware of) and not all the time. Some messages get through without any problem, others just disappear. The senders are not related at all. One is in another country, one uses AOL, one uses a corporate Exchange server locally. I can't seem to find a pattern. Where else can I look to try to figure out where these messages are going/getting captured? Are there additional logs that I can enable either within GFI or Exchange that might shed some light on this? Thanks. We are using Exchange 2003 on Server 2003. Desktop client is Outlook 2003 on Windows XP Pro.

    Read the article

  • Can't connect remotely to Windows Server 2008 R2

    - by JohnyD
    I have a new Dell R710 server running Windows Server 2008 R2. I one of it's 4 nic's set up and the rest are not being used. I have successfully given it an ip address, network mask, and dns servers. I can ping and resolve this machine from anywhere else in the network. However, when I try to connect to it via RDP it does several things: 1) it might just outright refuse me with the message, "This computer can't connect to the remote computer. Try connecting again." 2) it might connect me and let me chose the account I would like to log on as... but when you select an account then you receive the same message as in #1 3) it might actually allow you to connect but only for about 1 minute and then you receive the same message and it closes your session. I have configured the firewall service to allow for RDP over the domain network connection. This didn't have any noticible effect. I have now disabled the firewall for all 3 networks and have even stopped the Windows Firewall service. I am still having the same issue. I am new to Server 2008 R2 and things are very different. Please give me any advice you can on how to resolve this issue and/or any other gotchas that are sure to come my way. The 2003 - 2008 learning curve seems steep. Thanks

    Read the article

  • get-eventlog issue

    - by Jim B
    I wanted to get a quick report of some log entries I saw on a server, so I ran: Get-Eventlog -logname system -newest 10 -computer fs1 | fl I got events back however the descriptions were all wrong. Here's an example: Index : 1260055 EntryType : Warning InstanceId : 2186936367 Message : The description for Event ID '-2108030929' in Source 'W32Time' cannot be found. The local compute r may not have the necessary registry information or message DLL files to display the message, or you may not have permission to access them. The following information is part of the event:'time. windows.com,0x1' Category : (0) CategoryNumber : 0 ReplacementStrings : {time.windows.com,0x1} Source : W32Time TimeGenerated : 1/25/2010 10:43:31 AM TimeWritten : 1/25/2010 10:43:31 AM UserName : Note that if I pull the event ID property it's correct (in this case 38) Is this is known issue or is something wrong. The messages resolve fine via event viewer locally and remotely Here is the powershell version info: Name : ConsoleHost Version : 2.0 InstanceId : bc58fcf8-bba3-4ca8-8972-17dbd5d9ff08 UI : System.Management.Automation.Internal.Host.InternalHostUserInterface CurrentCulture : en-US CurrentUICulture : en-US PrivateData : Microsoft.PowerShell.ConsoleHost+ConsoleColorProxy IsRunspacePushed : False Runspace : System.Management.Automation.Runspaces.LocalRunspace Here is the revised version info: Name Value ---- ----- CLRVersion 2.0.50727.3603 BuildVersion 6.0.6002.18111 PSVersion 2.0 WSManStackVersion 2.0 PSCompatibleVersions {1.0, 2.0} SerializationVersion 1.1.0.1 PSRemotingProtocolVersion 2.1

    Read the article

  • Resuming downloads in Firefox

    - by Kim
    Unfortunately, Firefox still has failed to add the option to resume downloads. I've ran into this problem SO MANY times, and in my previous searches I found posts saying Firefox was going to fix that. As of 3.6.3 they haven't. I just tried Free Download Manager (FDM), again, having the Firefox addon Flashgot use it. The download gets passed to FDM, and fails, giving the error message "access denied, invalid username or password." No password was required. The site I'm trying to get the file from is turbobit.net, which limits downloads speeds to 100kb/sec, and has a 59 second countdown before you get the link. I guess it's transparently using a password on their end. If I just download normally (save to disk) the download starts fine, but it fails after 30 minutes to 1 hour (always different), and my Wi-fi connection will stop briefly - and I have to start all over. So I will never be able to download a large file. I also tried DTA instead of FMD with Flashgot, and I get an "access denied" message in DTA. Again, I reloaded - waited the 59 seconds, and download w/Firefox, and the download starts fine. The failure message in the Firefox Downloads window is "source file at http... could not be read." Any help would be greatly appreciated. When is Firefox going to finally add the ability to resume downloads????? Is there some other software I haven't found using Google that will work?

    Read the article

  • Why is 32-bit-mode required in IIS7.5 for my app?

    - by Jonas Lincoln
    I have a .net4 web application running in a 64 bits 2008 server. I can only get it to run when I set the app pool to Enable 32-bits application to true. All dlls are compiled for .net4 (verified with corflags.exe). How can I figure out why Enable 32-bit is required? The error message from the event log when starting as a 64-bit app-pool Event code: 3008 Event message: A configuration error has occurred. Event time: 2011-03-16 08:55:46 Event time (UTC): 2011-03-16 07:55:46 Event ID: 3c209480ff1c4495bede2e26924be46a Event sequence: 1 Event occurrence: 1 Event detail code: 0 Application information: Application domain: removed Trust level: Full Application Virtual Path: removed Application Path: removed Machine name: NMLABB-EXT01 Process information: Process ID: 4324 Process name: w3wp.exe Account name: removed Exception information: Exception type: ConfigurationErrorsException Exception message: Could not load file or assembly 'System.Data' or one of its dependencies. An attempt was made to load a program with an incorrect format. at System.Web.Configuration.CompilationSection.LoadAssemblyHelper(String assemblyName, Boolean starDirective) at System.Web.Configuration.CompilationSection.LoadAllAssembliesFromAppDomainBinDirectory() at System.Web.Configuration.AssemblyInfo.get_AssemblyInternal() at System.Web.Compilation.BuildManager.GetReferencedAssemblies(CompilationSection compConfig) at System.Web.Compilation.BuildManager.CallPreStartInitMethods() at System.Web.Hosting.HostingEnvironment.Initialize(ApplicationManager appManager, IApplicationHost appHost, IConfigMapPathFactory configMapPathFactory, HostingEnvironmentParameters hostingParameters, PolicyLevel policyLevel, Exception appDomainCreationException) Could not load file or assembly 'System.Data' or one of its dependencies. An attempt was made to load a program with an incorrect format. at System.Reflection.RuntimeAssembly._nLoad(AssemblyName fileName, String codeBase, Evidence assemblySecurity, RuntimeAssembly locationHint, StackCrawlMark& stackMark, Boolean throwOnFileNotFound, Boolean forIntrospection, Boolean suppressSecurityChecks) at System.Reflection.RuntimeAssembly.InternalLoadAssemblyName(AssemblyName assemblyRef, Evidence assemblySecurity, StackCrawlMark& stackMark, Boolean forIntrospection, Boolean suppressSecurityChecks) at System.Reflection.RuntimeAssembly.InternalLoad(String assemblyString, Evidence assemblySecurity, StackCrawlMark& stackMark, Boolean forIntrospection) at System.Reflection.Assembly.Load(String assemblyString) at System.Web.Configuration.CompilationSection.LoadAssemblyHelper(String assemblyName, Boolean starDirective) Request information: Request URL: "our url" Request path: "url" User host address: ip-adddress User: Is authenticated: False Authentication Type: Thread account name: "app-pool" Thread information: Thread ID: 6 Thread account name: "app-pool" Is impersonating: False Stack trace: at System.Web.Configuration.CompilationSection.LoadAssemblyHelper(String assemblyName, Boolean starDirective) at System.Web.Configuration.CompilationSection.LoadAllAssembliesFromAppDomainBinDirectory() at System.Web.Configuration.AssemblyInfo.get_AssemblyInternal() at System.Web.Compilation.BuildManager.GetReferencedAssemblies(CompilationSection compConfig) at System.Web.Compilation.BuildManager.CallPreStartInitMethods() at System.Web.Hosting.HostingEnvironment.Initialize(ApplicationManager appManager, IApplicationHost appHost, IConfigMapPathFactory configMapPathFactory, HostingEnvironmentParameters hostingParameters, PolicyLevel policyLevel, Exception appDomainCreationException) Custom event details:

    Read the article

  • Configure IIS to pass-through CGI output without any conditioning

    - by Daniel Watrous
    I'm building a web service on Windows 2008 R2 with IIS 7.5 and Python 2.5. Right now I have the Handler Mappings and everything else setup just fine, Except that IIS is modifying what it gets back from the CGI script before sending it along the the client. Here's an example: I wrote the following CGI script: # hello.py print "Status: 400 Bad Request" print "Content-Type: text/html" print print "Error Message" According to the HTTP spec this should be fine and a Status of 400 should allow for a description of the error message in the body of the response. When the server response actually comes back to me I get the following: Status: 400 Bad Request Date: Fri, 11 Feb 2011 17:58:30 GMT X-Powered-By: ASP.NET Connection: close Content-Length: 11 Server: Microsoft-IIS/7.5 Content-Type: text/html Bad Request I've seen on this forum and others where I can change or eliminate the X-Powered-By header element, but I would like IIS to leave it alone altogether. I'm not sure why it takes my response, deletes "Error Message" from the body and replaces it with "Bad Request" and then adds all that other junk in. Is there some way to tell IIS to just send the response along without making any changes at all?

    Read the article

  • Booting a Windows 7 installation on different hardware

    - by tomfanning
    I'm in a situation where I could do with very quickly migrating a Windows 7 (RTM x64) installation from one machine to another. What options are open to me in terms of getting W7 to boot after the drive is picked up and moved from one box to another? I thought it was supposed to be a little less sensitive to this kind of move than XP, but it doesn't work - it is stuck in a reboot loop and never reaches a GUI. Tried a few things so far, none of which have worked: Changed SATA mode in the BIOS of the target machine between ATA and AHCI run Windows 7 Startup Repair tried safe mode, no change (I will keep this list up to date as suggestions come in) UPDATE: I can confirm this reboot loop is due to STOP error 0x0000007B, and these codes follow: 0xFFFFF880009A98E8 0xFFFFFFFFC0000034 0x0000000000000000 0x0000000000000000 UPDATE: I didn't get anywhere on this and I ended up just rebuilding the machine. I think it should be theoretically possible, so I'm going to leave the question open in case someone comes along in future with an answer.

    Read the article

  • Postfix "mail-to-script" pipe only delivers empty messages

    - by user68202
    i have a problem here. I want that a incoming email is piped to a php script in the system through postfix. My System is running with ispconfig 3, postfix and dovecot (< virtual mailbox users are saved in mysql). I looked already into this one: How to configure postfix to pipe all incoming email to a script? ... the script is executed, but no "message" is delivered to the script. My setup so far: In ISPConfig 3 i have set up the following email route: Active Server Domain Transport Sort by Yes example.com pipe.example.com piper: 5 excerpt from my postfix master.cf: piper unix - n n - - pipe user=piper:piper directory=/home/piper argv=php -q /home/piper/mail.php so far it is working great (mail sent to [email protected]) (mail.log): Jun 21 16:07:11 example postfix/pipe[10948]: 235CF7613E2: to=<[email protected]>, relay=piper, delay=0.04, delays=0.01/0.01/0/0.02, dsn=2.0.0, status=sent (delivered via piper service) ... and no errors in mail.err the mail.php is sucessfully executed (its chmod 777 and chown'ed to piper), but creates a empty .txt file (normally it should contain the email message): -rw------- 1 piper piper 0 Jun 21 16:07 mailtext_1340287631.txt the mail.php script ive used, is the one from http://www.email2php.com/HowItWorks if i use their (commercial) service to pipe an email to the mail.php (in a apache2 environment) through a provided "pipe-email", the message is saved sucessfully and complete. But as you can see, i dont want to use external services. -rw-r--r-- 1 web2 client0 1959 Jun 21 16:19 mailtext_1340288377.txt So, whats wrong here? I think it has something to do with the "delivering configuration" in my system...

    Read the article

  • Outlook 2007 "Mark as Not Junk" Dialog Confusion

    - by David
    Outlook 2007's "Not Junk" button opens the "Mark as Not Junk" dialog. The dialog works correctly if I keep the "Always trust e-mail from <email address>" option checked. That is, the message is removed from the Junk folder and returns to the Inbox. However, if I uncheck the "Always trust" box, pressing OK dismisses the dialog, but nothing else happens. Why not? According to Outlook help, "When you mark a message as not junk, you are given the option of adding the sender or the mailing list name to your Safe Senders List or Safe Recipients List." That sure makes it sound like this is just an option, and not necessary for the core functionality of the action. I really don't want to trust a (possibly forged) From: address, but I do want my mail back in the Inbox. I could manually drag it, but I'm assuming that marking a message as not junk also trains some kind of bayesian filter. Am I mistaken? Thanks.

    Read the article

  • WWNs,WWPNs and Fibre Channel addresses

    - by user238230
    Lots of contradictory on these subjects and I don't know why. My first question is about the 64 bit WWN. One reference claims the terms WWN and WWPN are synonymous. An online source seems to refute this. They say: A WWPN (world wide port name) is the unique identifier for a fibre channel port where a WWN (world wide name) the unique identifier for the node itself. A good example is a dual port HBA. There will be two WWPN's (one for each port) and only a single WWN for the card itself. Question #1: Which is correct? I’m almost positive I read that every “Port” has a WWN. My next question is about the 24 bit FC address that is dynamically allocated to a port when it is introduced to the switch. The Domain ID field is defined as: "a unique number provided to each switch in the fabric." Question #2: Do Domain IDs only apply to switch ports? For example what would the Domain ID be for a HBA? None? The same as the switch port it is connected to? Question #3: My last question is about the Name Server of a switch. A book example shows the routing of a message through the switch. It uses the WWNs of the source and destination ports to route the message. I am assuming that the Name Server must associate the WWN and the FC address in some way in order to route the message, correct?

    Read the article

  • Oracle: Getting ORA-01195 and ORA-01110 when attempting resetlogs

    - by MacAnthony
    I am trying to get our database to startup. When I login to sqlplus and do a startup, I get the message: Total System Global Area 534462464 bytes Fixed Size 2215064 bytes Variable Size 331350888 bytes Database Buffers 192937984 bytes Redo Buffers 7958528 bytes Database mounted. ORA-01589: must use RESETLOGS or NORESETLOGS option for database open So I do a shutdown, startup mount (which works fine) and then run: SQL> alter database recover using backup controlfile until cancel; alter database recover using backup controlfile until cancel * ERROR at line 1: ORA-00283: recovery session canceled due to errors ORA-19909: datafile 1 belongs to an orphan incarnation ORA-01110: data file 1: '/<path>/system01.dbf' SQL> alter database open resetlogs; alter database open resetlogs * ERROR at line 1: ORA-01195: online backup of file 1 needs more recovery to be consistent ORA-01110: data file 1: '/<path>/system01.dbf' I know I've used instructions to get me past this error before, but I seem to be having trouble tracking it down. A bit of history: We wanted to refresh the data in this from another db so we attempted to do a expdb/impdb into this instance. The impdb did not complete correctly and got an end of file error message in it and hung (I still have the message in a log if it's important). Since the instance would start at this point, we decided to use the hotbackup process we have to restore the db. The hotbackups are from another server/instance. We went through the same process 2 weeks ago. At the point of recreating the control file is where we got to the issue above.

    Read the article

  • Extract and view Outlook contacts attachment sent to Gmail

    - by matt wilkie
    A friend forwarded a contact list to my gmail account from Outlook (2007 or 2010, not sure which). I can see there is an attachment in gmail but when I save it to my local drive it's just a plain text file containing the text This attachment is a MAPI 1.0 embedded message and is not supported by this mail system. If I use gmail's "show original message" it contains in part: This is a multipart message in MIME format. ------=_NextPart_000_0016_01CC6656.CE12F030 Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: 7bit ------=_NextPart_000_0016_01CC6656.CE12F030 Content-Type: application/ms-tnef; name="winmail.dat" Content-Transfer-Encoding: base64 Content-Disposition: attachment; filename="winmail.dat" eJ8+Ih0VAQaQCAAEAAAAAAABAAEAAQeQBgAIAAAA5AQAAAAAAADoAAEIgAcAGAAAAElQTS5NaWNy b3NvZnQgTWFpbC5Ob3RlADEIAQgABQAEAAAAAAAAAAAAAQkABAACAAAAAAAAAAEDkAYASAgAACgA --8<---snip---8<-- GUC/9NKH95rABgMA/g8HAAAAAwANNP0/pQ4DAA80/T+lDvAm ------=_NextPart_000_0016_01CC6656.CE12F030-- How do I save the attached winmail.dat properly, and open the winmail.dat and extract the contact list? I'm running Windows 7 x64, but have access to an ubuntu linux vmware appliance if needed. I have Outlook 2010, but can't use it to connect directly to gmail as pop3 and imap are blocked by the corporate firewall.

    Read the article

  • server 2008 r2 stuck on installing updates

    - by volody
    I have 2008 r2 64bit server that is stuck on installing updates. It shows message "Please do not power off or unplug your machine. Installing 57 of 61.." This message is shown for 3 hours now. I was trying to connect to this server using mmc. runas /user:AdministratorAccountName@ComputerName "mmc %windir%\system32\compmgmt.msc" RUNAS ERROR: Unable to run - mmc C:\Windows\system32\compmgmt.msc 1311: There are currently no logon servers available to service the logon request. What else can I do? Update: Remote Desktop does not work. It just disappear after entering username and password from Win7-64 computer Update: I have disconected server. Now Server Manager in Roles Summary shows message "Unexpected error refreshing Server Manager: The remote procedure call failed." Event log shows Could not discover the state of the system. An unexpected exception was found: System.Runtime.InteropServices.COMException (0x800706BE): The remote procedure call failed. (Exception from HRESULT: 0x800706BE) at System.Runtime.InteropServices.Marshal.ThrowExceptionForHRInternal(Int32 errorCode, IntPtr errorInfo) at Microsoft.Windows.ServerManager.ComponentInstaller.ThrowHResult(Int32 hr) at Microsoft.Windows.ServerManager.ComponentInstaller.CreateSessionAndPackage(IntPtr& session, IntPtr& package) at Microsoft.Windows.ServerManager.ComponentInstaller.InitializeUpdateInfo() at Microsoft.Windows.ServerManager.ComponentInstaller.Initialize() at Microsoft.Windows.ServerManager.Common.Provider.RefreshDiscovery() at Microsoft.Windows.ServerManager.LocalResult.PerformDiscovery() at Microsoft.Windows.ServerManager.ServerManagerModel.CreateLocalResult(RefreshType refreshType) at Microsoft.Windows.ServerManager.ServerManagerModel.InternalRefreshModelResult(Object state) Update: Manual update hangs on (Installing update 58 of 62...) Seurity Update for Windows Server 2008 R2 x64 Edition (KB979309) Update: It could be an issue with that admin user was renamed

    Read the article

  • Upstart Script on Centos 6

    - by MarcusMaximus
    I'm trying to create an upstart script to run a python script on startup. In theory it looks simple enough but I just can't seem to get it to work. I'm using a skeleton script I found here and altered. description "Used to start python script as a service" author "Me <[email protected]>" # Stanzas # # Stanzas control when and how a process is started and stopped # See a list of stanzas here: http://upstart.ubuntu.com/wiki/Stanzas#respawn # When to start the service start on runlevel [2345] # When to stop the service stop on runlevel [016] # Automatically restart process if crashed respawn # Essentially lets upstart know the process will detach itself to the background expect fork # Start the process script exec su nonrootuser -c "python /usr/local/scripts/script.py" end script The test script I want it to run is currently a simple python script that runs without any issue when run from a terminal. #!/usr/bin/python2 import os, sys, time if __name__ == "__main__": for i in range (10000): message = "shotgunUpstartTest " , i , time.asctime() , " - Username: " , os.getenv("USERNAME") #print message time.sleep(60) out = open("/var/log/scripts/scriptlogfile", "a") print >> out, message out.close() The location/var/log/scripts has permissions 777 The file /usr/local/scripts/script.py has permissions 775 The upstart script /etc/init.d/pythonupstart.conf has permissions 755

    Read the article

  • What's the utility of the return command in autohotkey?

    - by Shashank Sawant
    In the instances where the return command returns a value, the utility is obvious. I have seen the return command being used even when it is seemingly unnecessary. Let me show the following examples: Example 1: Loop { if a_index > 25 break ; Terminate the loop if a_index < 20 continue ; Skip the below and start a new iteration MsgBox, a_index = %a_index% ; This will display only the numbers 20 through 25 } Example 2: IfWinExist, Untitled - Notepad { WinActivate ; Automatically uses the window found above. return } Why is the return command used in Example 2 but is not used in Example 1? Both examples are copy-pasted/modified-pasted from the autohotkey.com's documentation.

    Read the article

  • Exchange 2010 Transport rules stepping on each other

    - by TopHat
    I have a group of users that I have to restrict email access for and so far using Exchange Transport Rules has worked very well. The problem I am having is that Rule 0 is supposed to bcc the email to a review mailbox but otherwise not change anything and Rule 9 is supposed to block the email and throw a custom NDR to tell the user why they were blocked. Here are my results in practice however. If Rule 0 is enabled and Rule 9 is enabled then only Rule 9 functions If Rule 0 is disabled and Rule 9 is enabled then Rule 9 functions If Rule 0 is enabled and Rule 9 is disabled then Rule 0 functions This is after the Transport Service has been restarted (multiple times actually). I have other rule pairs that work correctly. None of these are overlapping rulesets however. - copy email going to address outside domain and then block - copy email coming in from outside and then block Here is the rule for copying internal emails (Rule 0): Apply rule to messages from a member of Blind carbon copy (Bcc) the message to except when the message is sent to a member of or [email protected] Here is the rule to block the same email (rule 9): Apply rule to messages from a member of send 'Email to non-supervisors or managers has been prohibited. Please contact your supervisor for more information.' to sender with 5.7.420 except when the message is sent to , [email protected], The distribution group used for membership in these rules is used for the other blocking and copying rules and works as expected. Is there something I missed in this setup? All of the copy rules are at the front of the transport rule group and all the actual copies at at the end of the queue if that makes a difference. Any thoughts as to why the email doesn't get copied when it gets blocked?

    Read the article

< Previous Page | 241 242 243 244 245 246 247 248 249 250 251 252  | Next Page >