Search Results

Search found 8190 results on 328 pages for 'switch'.

Page 245/328 | < Previous Page | 241 242 243 244 245 246 247 248 249 250 251 252  | Next Page >

• Routing WIFI and LAN for specific traffic

  - by jakebird451

  I have two network devices aboard my macbook pro: WIFI (en1): Used for general traffic. Connects to an ip of 192.168.19.* via DHCP LAN (en0): Used for specific traffic. Connects to an ip of 192.168.2.10 as a static IP. Does not connect to a router, only a switch for direct routing connection. I have 4 IP addresses I need to access on the LAN: 192.168.2.1 192.168.2.21 192.168.2.20 192.168.2.30 The rest of the traffic needs to go to WIFI. I have tried setting up a routing table for the specific ip addresses, but I only managed to mess up my network. I do not venture out into the world of networking too often, but this was the latest command I have been trying: sudo route add -host 192.168.2.30 -interface en0 This command killed my ability to use ping. It told me that ping could not allocate memory (is that even possible)? It also killed my wifi access. Logging out and back in fixed the issue. I really do not mind to make this solution permanent, so I am fine with a temporary routing.

  Read the article

• SRM 4 Test Fails with message for some VM : Error: A specified parameter was not correct.

  - by Setesh

  Here are my architecture : For the protected site 4 Host VSphere Enterprise Plus, each one with 2 HBAs FC connected to the switch fabric, connected to an EMC CX4-120 1 VCenter 1 SRM For the recovery site 2 Hosts Vsphere 4 1 Vcenter 1 SRM 1 CX-4-120 The CX4-120 is connected to the second CX4-120 with ISCSI and the MirrorView / Asynchronous. I synchronise for the time 6 Lun on a FC DAE, 2 on a S-ATA DAE I have allocated 30% of the amount synchronised LUN for the SNAPSHOT us, but I have allocated them only on my S-ATA II DAE. It does not make a problem, my snapshot are correctly active. All the installation is new (hardware and software), installed in January with the last files available in download. I have a strange problem, and it's random, sometimes when I run a test on my RP, some VMs have this error : Error: A specified parameter was not correct. I don't know where to look. Any help is appreciated... PS : I have checked on all the VMs, no Floppy disk or CD attached. PS2 : There is severals VMs with RDM and OCFS2 filesystems on it.

  Read the article

• How can I make my Super keys (Windows Key) behave more like Ctrl/Alt/Shift in Linux

  - by deltaray

  After using the Ctrl + "arrow keys" for 13 years to switch virtual desktops in X windows, I've been convinced recently to change to using the Super keys instead (the windows key and the context menu key, which I've remapped). This all works fine for the most part. However, something is still picking up the key events that these keys are sending as if they are a normal alphanumeric like key. For example, I first noticed this in Google Docs spreadsheet that if I press the windows key alone over top of a cell, that it starts editing that cell. It doesn't insert anything, it just sends a key event that Firefox sees and starts editing the cell. This caused problems on a collaborative document I was working on as the way Google docs works, it led to me accidentally erasing the data in a few fields before I realised what was going on. I like using the super keys, but I want them to behave more like a Ctrl or Alt key does in that its a modifier key and doesn't send anything until a second key is pressed. My setup is the following: Ubuntu 10.10 XFCE 4 Microsoft Natural Ergo 4000 keyboard (with the logo scratched out) The following is my .Xmodmap file: remove Lock = Caps_Lock keycode 66 = Escape ! The below maps my other windows context menu key. keycode 135 = Super_R Edit: As requested, here is the relevant output from xev for a keypress and keyrelease of my Super_L (left windows key) KeyPress event, serial 34, synthetic NO, window 0x8200001, root 0x15d, subw 0x0, time 2428849342, (177,174), root:(182,228), state 0x10, keycode 133 (keysym 0xffeb, Super_L), same_screen YES, XLookupString gives 0 bytes: XmbLookupString gives 0 bytes: XFilterEvent returns: False KeyRelease event, serial 34, synthetic NO, window 0x8200001, root 0x15d, subw 0x0, time 2428849430, (177,174), root:(182,228), state 0x50, keycode 133 (keysym 0xffeb, Super_L), same_screen YES, XLookupString gives 0 bytes: XFilterEvent returns: False

  Read the article

• Microphone doesn't work

  - by mandy

  I'm having a trouble with my built in microphone. Even if I use headphone with mic, it doesn't really work. The weird thing is, if I clap the green lines of the speaker icon jumps, but if I speak it doesn't. I have also tried some recordings, but I can not hear myself and adjusting the volume didn't help at all. I tried to restore it, still no change. I have updated it in the device manager, but it said there that it's up to date and the devices are working properly. Until I decided to recover the whole system (wherein I pressed zero and switch on button) to my surprise, the settings became different, most programs were deleted, even my files. It's like it was formatted and I'm so sad that the mic was not fixed. I really don't know what to do now. My laptop model is Toshiba satellite m840. I want to it return to its settings/set up just before I Recover the system and bring back all the programs that we're installed and of course, most of all, to fix my microphone so I can use Skype again and other video calling application.. I hope someone could help me. Thanks a lot!

  Read the article

• Chrome Lockups Windows 7 64-bit

  - by Mike Chess

  I'm running Google Chrome (6.0.427.0 dev) on Windows 7 Home Premium 64-bit (AMD Phenom 3.00 GHz, 8 GB RAM). The computer lockups hard after running Chrome for about five minutes. The lockup happens whether Chrome is actually being used to browse web sites or it is just idling. No programs can be started or interacted with when this happens. The computer must be power-cycled to recover. The lockup happens regardless of which web sites are being browsed. The system event logs do not show any events around the time when the lockup transpired. All other applications run just fine on this system. In fact, Chrome ran without issue for several months on this system (the system was brand new 03-2010). I also run the same version of Chrome on other computers (Windows XP SP3) without issue. I've come to really like Chrome and use it as my default browser whenever possible. What could be causing Chrome to cause the system to lockup as it does? Does Chrome have any logs that aren't part of the Windows event log? Does Chrome have a debug command line switch that might reveal more about what happens?

  Read the article

• Does anyone know where I could find a 2 input USB voltage meter?

  - by John O

  What we really need is a tiny UPS, of sorts. We'll be hooking up a solar cell and a battery to a single board computer. Currently, that SBC is a custom Pic32 device, and it does it's own UPS and voltage monitoring duties. I've been tasked with trying to replicate all of its features with off the shelf products... and for the most part I've succeeded. But I don't currently have any way to switch between two sources of juice, or monitor when they're getting low. These guys have something: http://www.mini-box.com/picoUPS-100-12V-DC-micro-UPS-system-battery-backup-system I really like it, the price is well within the budget. We might even work it in though it does 12V and I'll probably be using 5V... there are enough engineers on hand to figure out something. But I'd still have no idea what the voltage was for the PV or battery. I was hoping that there was some simple little USB multimeter thing that I could use to monitor this with, but I can't seem to come up with anything. I've found all sorts of cool hardware, but nothing that will help us. Does anyone know of anything?

  Read the article

• Separated virtual networks with same subnet range with 2 interface

  - by Coolpet

  I'm having some problems with routing with the following: I have a server with 2 interfaces. It has 1-1 alias contains the same subnet. the 2 interface is connected to 2 switch, which are separated from each other. Infrastructure: Eth0 192.168.16.2/20 Eth0:eth0 192.168.1.222/20 Eth1 192.168.32.3/20 Eth1:eth1 192.168.1.223/20 I have a PC which has the IP address: 192.168.1.3/24 The problem is the next: If PC is on subnet 1, I can ping it. If PC is on subnet 2, I can't ping it. traceroute shows the route is across 192.168.1.222 ping -I 192.168.1.223 192.168.1.3 is not working on subnet 2. arp entries show the MAC address belonging to the correct interface (eth1 on subnet 2) How can I force the server to look on both interface same ranged subnet for specific IP? It searches only in the first subnet. The routing table has these 2 entries: 192.168.0.0/20 dev eth0 proto kernel scope link src 192.168.1.222 192.168.0.0/20 dev eth1 proto kernel scope link src 192.168.1.223

  Read the article

• mail server checklist..

  - by Jeff

  currently we ran into some issues with our mail server setup. im preparing a list of actions that we should enforce and use in order to maintain a proper email solution within our company. we have around 80 exchange users, and send mass emails out almost on a monthly bases to 20,000 + customers each time.. the checklist i currently have: 1) mcafee mxlogic 'cloud' anti-spam functionality for incoming message. 2) antivirus on each computer in company 3) antivirus on exchange and DNS servers 4) setup SPF record 5) setup DKIM 6) setup domainkey 7) setup senderID 8) submit spf to microsoft, yahoo, etc. for 'whitelist' purposes. 9) configure size limits for messages in exchange to safe numbers 10) i have 2 outside IPs for my email server, incase one gets blacklisted, switch to the backup. 11) my internet site rests on a different ip than the mail server 12) all mass emails for company sent through 3rd party company (listtrak.com) 13) setup domain alias, media, enews, and bounce for the 3rd party mass mail software. 14) verify the setup using [email protected] 15) configure group policy and our opendns.org account to prevent unwanted actions and website viewing mass emails: 1) schedule them to send different amounts at different times (1,000 at 10am, 1,000 at 4pm, 1,000 10am next day).. 2) setup user prefences, decide what they want to receive ect. ( there interests) 3) send a more steady flow of email, maybe 100 a week with top new products instead of 20,000k every other month.. if anyone has suggestions or additions/subtractions to this checklist they are greatly appreciated. thank you

  Read the article

• I need to build a mini computer lab with 6 PCs

  - by chiurox

  Hello everyone, This weekend I need to build a mini computer lab with 5-6 PCs. The purpose is for a small computer class that will be taking place. They're mostly going to be doing office and daily kind of stuff, so nothing high performance. However, I hope it will last at least for 2 more years. I already have some parts for 2 PCs, one is a P4 3.0 and another is Celeron 2.4GHz, both socket 478. For the other 4 PCs, I'm wondering if I should buy individual parts and put it all together or get workstations like those Dell Optiplex with P4s. To put things into perspective, I am not currently in the US. I'm in South America and prices here are ridiculously. Another really important thing is that I need to share an internet connection between a total of 8 PCs at this place. Right now I only have a crappy wireless router, should I get another one? Or go with switch hub? I'm not experienced in this matter. Thanks guys!

  Read the article

• Bridging networks problems

  - by Eric

  In my setup I have 3 computers and 2 (wireless d-link) routers. Computer1 has ethernet and wireless interfaces ethernet : 192.168.0.x (DHCP) wireless : 192.168.10.254 (static) Computer 2 has ethernet with two ips ethernet1 : 192.168.0.90 (static) ethernet2 : 192.168.10.110 (static) Computer 3 is a particular device with a hardcoded ip that I can't change wireless : 192.168.10.41 (static) Router1 manages internet and DHCP for network 192.168.0.0/24 Router2 is more complicated. I don't use DHCP. I use it to bridge between both networks. Its static ip is 192.168.10.1 Computer1 can ping Computer2. Computer1 can ping Computer3. Computer1 can ping Router1. Computer1 cannot ping Router2. Computer2 cannot ping Computer3. Computer2 can ping Router2. Router1 can ping Router1 Router2 can ping Computer2 Router2 cannot ping Computer1 Router2 cannot ping Computer3 This is very weird. Router2 manages the wireless connection, it should be able to ping its own computers right? My question is obviously : How can I make it so Computer2 can access everything else. This is a traditional case of "it was working before christmas and now it doesn't". The ethernet wiring is as follow : [ Computer1 ]----[ Router1 ]---[ Router2 ]---[ Computer3 ] I am using switch (lan) ports on Router1/2.

  Read the article

• Linux as a gateway (no NAT)

  - by Hugo

  I'm trying to configure a linux server as a gateway/router, but I can't get it to work, and all information I've managed to find is NAT-related. I have a public IP block for the gateway and devices behind it, so I want the gateway to simply route packets to the internet - again: no NATing! I've managed to get the gateway to access the internet successfully (that was just a matter of configuring the IP and GW), and the computers behind it can communicate with it. [EDIT: more info] This is actually an IPv6 block (2800:40:403::0/48) (but I've found that most utilities and instructions can be easily adapted from IPv4 to IPv6 with little hastle). The server has too ports: wan: 2800:40:403::1/48 lan: 2800:40:403::3/48 One of the computers behind it is connected to it via a switch; 2800:40:403::7/48 The wan interface on the server can ping6 www.google.com without issues. The lan interface on the server and the client can mutually ping each other without issues (as well as SSH, etc). I've tried setting the server as a default gateway for the client, with no luck: client # route -A inet6 add default gw 2800:40:403::3 dev eth1 server # cat /proc/sys/net/ipv6/conf/all/forwarding 1 I don't want any filtering/firewalling/etc, just plain routing. Thanks.

  Read the article

• Allied Telesis router: IP filtering for the LOCAL interface

  - by syneticon-dj

  Given an Allied Telesis router with an AlliedWare OS (2.9.1) I would like to disable access to all management services of the router except for a number of subnets (or alternatively have what is a "management VLAN" with other manufacturers' switch and router models). What I have tried so far: creating a new VLAN and an appropriate IP interface, setting the LOCAL IP into this subnet, creating an IP filter for the IP interface and specifying my exclusion subnets: it simply does not work as intended as I can access the LOCAL IP set from any of the other VLAN interfaces - the traffic is apparently not going through my defined filter set at all creating a new IP filter set and binding it to the LOCAL IP interface: this seems not to affect any kind of traffic at all, the counters for the filter set remain at zero packets setting the Remote Security Officer Level IP address range: this only restricts the ability for a user with the Security Officer privilege level to log in from any but the specified address ranges / subnets. Unfortunately, it does not prevent service availability (and thus DoS capacity) or the ability to log in as a less privileged user (e.g. a "manager") calling technical support: unfortunately no solution so far What I have not tried: creating a filter set for each and every IP interface defined on the router and excluding access to the router's management IP: I would like to reduce the overhead induced by IP filters as the router already is CPU-constrained at times. Setting up filters for every IP interface would mean that each and every traffic packet would have to pass the filters, thus consuming CPU cycles. If by any means possible, I would like to find a different solution.

  Read the article

• Siege - running a stress test benchmark

  - by morgoth84

  I need to do a benchmark test of a HTTPS server using Siege, to see how it behaves under massive load. I'm initiating tests from another machine which is quite powerful and it is connected to the same physical switch the server is connected on. But when I initiate a test, I can't get it to make more than 170 requests per second. With this load the server's CPU usage is at 15-20% and the average response time for a request is approx. 0.03 seconds. Load of the client machine is approx. at 10%. So, I gradually increase the number of users in Siege (the number of worker threads) and request rate linearly increases up to 170 reqs/sec, but it never gets over it. No matter how many more worker threads I start, the load on the server is never more than 20% (and the client's load also doesn't increase any more). How can I overcome this? I've googled a bit and found out that after a request is completed, a socket associated with one ephermal port remains in WAIT_TIME state for some time during which it can't be reused. I tried to overcome this by doing these things: sysctl -w net.ipv4.ip_local_port_range="1024 65535" echo 1 > /proc/sys/net/ipv4/tcp_tw_recycle Oh, and the client machine is a Linux (RedHat, I think, but I'm not sure). Any help would be appreciated.

  Read the article

• How do I setup routing for two companies with different Internet connections on the same LAN?

  - by Clint Miller

  Here's the setup: Two companies (A & B) share office space and a LAN. A 2nd ISP is brought in and company A wants its own Internet connection (ISP A) and company B wants its own Internet connection (ISP B). VLANs are deployed internally to separate the two companies' networks (company A: VLAN 1, company B: VLAN 2, shared VOIP: VLAN 3). With separate VLANs it's simple enough to use separate DHCP servers (or separate scopes on the same server) to assign the default gateway to each company's gateway for their Internet connection. Static routes can be created on each gateway to point traffic destined for the other company's VLAN or the voice VLAN so that all nodes are reachable as expected. However, I think this is a form of asymmetrical routing, right? (The path from node A1 to node B1 is not the same as the path back from node B1 to node A1). Can I set up policy-based routing to correct this? In that case, can I assign the same default gateway to every device on all VLANs and create a routing policy on a L3 switch to look at the source address and forward traffic to the appropriate next hop? In that case, I want the routing logic to go like this: If the destination address is known, forward the traffic (traffic destined for a different VLAN). If the destination address is unknown, forward the traffic to ISP A's gateway if the source address is on VLAN A; or forward the traffic to ISP B's gateway if the source address is VLAN B. Am I thinking about this problem in the correct way? Is there another way to solve this problem that I am overlooking?

  Read the article

• What is the --daemon option?

  - by Pascal Dimassimo

  I was installing Solr with Jetty using these instructions. Basically, those instructions made you download the Jetty startup script and copy it to /etc/init.d/jetty. But it was not working. Each time I was starting Jetty, I had a "FAILED" message and nothing to understand why it was happening. I decided to open up the /etc/init.d/jetty script to understand what was happening. I saw that this script was using start-stop-daemon to launch jetty. After a couple of time of debugging, I discovered that removing the --daemon option at the end of the start-stop-daemon call was fixing my problem. I did a couple of research and discovered that this guy had the same problem and resolved it like I did: my removing the --daemon option. What is weird is that the switch does not seem to be specific to start-stop-daemon, because it is not documented in the man page. Also, I've seen it used for other commands. So what is that --daemon option doing? And why removing it resolved my problem? Note that I am working on Ubuntu 10.04.2 LTS.

  Read the article

• Apache with multiple domains, single IP, VirtualHost is catching the wrong traffic

  - by apuschak

  I have a SOAP web service I am providing on a apache web server. There are 6 different clients (IPs) that request data and 3 of them are hitting the wrong domain. I am trying to find a way to log which domain name the requests are coming from. Details: ServerA is the primary ServerB is the backup domain1.com - the domain the web service is on domain2.com - a seperate domain that server seperate content on ServerB ServerA is standalone for now with its own IP and DNS from domain1.com. This works for everyone. ServerB is a backup for the web service, but it already hosts domain2.com. I added entries into the apache configuration file like: <VirtualHost *:443> ServerName domain2.com DocumentRoot /var/www/html/ CustomLog logs/access_log_domain2443 common ErrorLog logs/ssl_error_log_domain2443 LogLevel debug SSLEngine on ... etc SSL directives ... </VirtualHost> I have these for both 80 and 443 for domain1 and domain2 with domain1 being second. The problem is when we switch DNS for domain1 from ServerA to ServerB, 3 out of the 6 clients show up in the debug logs as hitting domain2.com instead of domain1.com and fail their web service request because domain2.com is first in the apache configuration file and catching all requests that don't match other virtualhosts, namely domain1.com. I don't know if they are hitting www.domain1.com, domain1.com (although I added entries for both) or using the external IP address or something else. Is there a way to see which URL they are hitting not just the page request or someother way to see why the first domain is catching traffic meant for the second listed domain? In the meantime, I've put domain1.com higher in the apache configuration than domain2.com. Now it catches the requests for all clients and works, however I don't know what it is catching and would like to make domain2.com the first entry again with a correct entry for domain1.com, for however they are hitting it. Thank you for your help! Andrew

  Read the article

• after building in more ram, bios/debian does nothing [closed]

  - by derty

  My private server has 2x1gb Ram working with a 64bit Debian and an Q6600 Intel. This runs 2 virtual mashines on it each one recives 512mb RAM. Which you can immagine is a bit tight for the hole system. Now i got 2x2gb ram from a friend. I'm not sure if thery are clocking at the same speed, but i'm sure my power adaptor is not on his limit and can handle that. So there are 2 ram sockets left at the mainboard. I shuted down the system and build in the 4 gigs and looked what happen. After pressing the start button, everything gets noisy as known BUT the screen shows nothing, not even the bios stuff it usally does. Why isn't the system booting? I can immagine that it does not direkt link between booting debian and the bios not showing a thing. Or is it Grub? I mounted the system disk, and i can see it, switch folders write stuff with "vim" it does not seems like there is a problem.

  Read the article

• Advice on cloning disk

  - by hks

  I'm going to buy a second disk for backup, the same size as my laptops. I want to mount it in a casing via usb and backup an entire hdd every soemtime. That's because I want the posibility to just switch drives in case of something goes wrong. I'm using Linux and obviously the right tool seems to be dd. The thing is that my laptop drive has a speed of around 50-70 MB/s and usb 2.0 is 57 MB/s. So to copy my 250GB disk should take me more than 1 hour if I'm lucky. I can't wait this much. I want some differential backup. I read one of JWZ articles. In it he gives more details for using rsync on Mac. He writes that there is possibility of making rsync'ed disk bootable. So my question is: how to make rsync'ed hdd bootable under Linux or are there other 'quick backup' tools for Linux that would allow me to just swap drives? Or should I just stick to dd :( ?

  Read the article

• file read performance degrades as number of files increases

  - by bfallik-bamboom

  We're observing poor file read IO results that we'd like to better understand. We can use fio to write 100 files with a sustained aggregate throughput of ~700MB/s. When we switch the test to read instead of write, the aggregate throughput is only ~55MB/s. The drop seems related to the number of files since the throughput for read and write are comparable for a single file then diverge proportionally as we increase the number of files. The test server has 24 CPU cores, 48GB of memory, and is running CentOS 6.0. The disk hardware is a RAID 6 array with 12 disks and a Dell H800 controller. This device is partitioned with ext4 using the default settings. Increasing the readahead (using blockdev) improves the read throughput significantly but it still doesn't match write speed. For instance, increasing the readahead from 128KB to 1M improved the read throughput to ~145MB/s. Is this a known performance issue in our OS/disk/filesystem configuration? If so, how can we tell? If not, what tools or tests can we use to further isolate the issue? Thanks.

  Read the article

• Why is my rsync so slow?

  - by iblue

  My Laptop and my workstation are both connected to a Gigabit Switch. Both are running Linux. But when I copy files with rsync, it performs badly. I get about 22 MB/s. Shouldn't I theoretically get about 125 MB/s? What is the limiting factor here? EDIT: I conducted some experiments. Write performance on the laptop The laptop has a xfs filesystem with full disk encryption. It uses aes-cbc-essiv:sha256 cipher mode with 256 bits key length. Disk write performance is 58.8 MB/s. iblue@nerdpol:~$ LANG=C dd if=/dev/zero of=test.img bs=1M count=1024 1073741824 Bytes (1.1 GB) copied, 18.2735 s, 58.8 MB/s Read performance on the workstation The files I copied are on a software RAID-5 over 5 HDDs. On top of the raid is a lvm. The volume itself is encrypted with the same cipher. The workstation has a FX-8150 cpu that has a native AES-NI instruction set which speeds up encryption. Disk read performance is 256 MB/s (cache was cold). iblue@raven:/mnt/bytemachine/imgs$ dd if=backup-1333796266.tar.bz2 of=/dev/null bs=1M 10213172008 bytes (10 GB) copied, 39.8882 s, 256 MB/s Network performance I ran iperf between the two clients. Network performance is 939 Mbit/s iblue@raven $ iperf -c 94.135.XXX ------------------------------------------------------------ Client connecting to 94.135.XXX, TCP port 5001 TCP window size: 23.2 KByte (default) ------------------------------------------------------------ [ 3] local 94.135.XXX port 59385 connected with 94.135.YYY port 5001 [ ID] Interval Transfer Bandwidth [ 3] 0.0-10.0 sec 1.09 GBytes 939 Mbits/sec

  Read the article

• Out of memory errors but not actually out of memory...

  - by commradepolski

  So, myself and my fellow support techs have been fighting with this issue and we still dont know what the problem is. Lets start off with the system specs: Windows XP 32 bit Corporate (SP2 and SP3) Intel D975XBX2 Mobo 4gb of ram Intel Core 2 Quad Q6600 ATI Radeon HD 3600 - 512mb After a few hours of working on the machine, the end user will begin to see the following symptoms: Out of memory messages Title bars and menus dont draw in properly Problems accessing network resources Problems opening up documents such as MSWord and MSPowerpoint and text files Problems opening up explorer windows General instability We have looked at task manager while this issue was occurring, and all indicators, like PF usage, threads, handles, etc. are normal. We have been having trouble pinpointing the root cause of this issue. It is also not situated with one user, it affects 8-10. So far we have tried: Resetting CMOS (Waiting to see results) Replacing video card (didnt help) Windows updates (didnt help) Updating network drivers (didnt help) Switching user from 1gbps to 100mbps network connection (awaiting results) Swapping the affected user's hardware (waiting for results) Increasing desktop heap size (helped for a bit but then the issue became more frequent) Applying the /3 switch to XP (didnt help) Increasing and decreasing and setting PF to system managed state (didnt help) We did have a power outage at the office a couple weeks ago, and all these issues became more frequent. Prior to the power outage it may take a week or so for the users to experience the issues but since the power outage it takes 3-4 hours or less. We havent had reports of the above issues causing BSODs, although that would be easier to diagnose :). Any help is greatly appreciated.

  Read the article

• Why is my browser using so much memory?

  - by Steve

  Hi. I've recently had problems with Firefox running very slowly when I have many tabs open; say 20 tabs. My whole system would slow down. I decided to give Google Chrome a try, and it started out fine. But lately I am finding that it too, slows down my whole system. Looking at Task Manager, chrome.exe is using about 250MB of memory in about 6 different entries in task manager. However, when I shut Chrome down, memory usage is reduced by about 600MB. How can this be? (shows drop in memory usage after ending Chrome.) When my system locks up with Chrome having many tabs open, it takes 10 seconds to load the Start Menu, 10 seconds to expand All Programs, and each folder and subfolder, and 30 seconds for the program to be highlighted under my mouse. It also takes 10 seconds to switch to Notepad. Why is Chrome appearing to use so much more memory than Task Manager indicates? Why is my pagefile being used when I have around 1.1GB of memory? Can I set Chrome to run in RAM and not in the pagefile? How can 20 tabs use 600MB? That's 30MB per tab. Thanks for your help.

  Read the article

• Two network adapters in one WindowsXP PC, how to make them work?

  - by Deele

  I have a need to set up network so I can use two ethernet cards inside one Windows (Windows XP SP2) based PC, one for internet connection, second, for internal LAN. How should I configure each NIC, with what IP's, subnet masks and gateways, so I can use inernet on my PC and get in touch with devices on my LAN? I have found that there are some sort of re routing nessesary inside my PC, but how does it work? I have already set up some configuration already, but I can't use it together with PC #1 NIC #1 connected. I need to disconnect, to access NIC WEB interface. Current configuration: Switch #1 and PC #1 NAS #2 are gigabit one's, so I could access NAS with gigabit speed. PC #1 NIC #1 IP XX.XXX.162.106 SN 255.255.255.248 GW XX.XXX.162.105 PC #1 NIC #2 IP 10.0.0.1 SN 255.255.0.0 GW 0.0.0.0 NAS #1 NIC #1 IP 10.0.0.12 SN 255.255.0.0 GW 0.0.0.0 My question is - what exact configuration should I do for every NIC in this LAN, so it would work? Is it possible to achieve internet access for Laptop, that is inside that NIC #2 LAN (should I just set up basic ICS)?

  Read the article

• Prevent rmdir -p from traversing above a certain directory

  - by thepurplepixel

  I hacked together this script to rsync some files over ssh. The --remove-source-files option of rsync seems to remove the files it transfers, which is what I want. However, I also want the directories those files are placed in to be gone as well. The current part of the find command, -exec rmdir -p {} ; tries to remove the parent directory (in this case, /srv/torrents), but fails because it doesn't have the right permissions. What I'd like to do is stop rmdir from traversing above the directory find is run in, or find another solution to get rid of all the empty folders. I've thought of using some kind of loop with find and running rmdir without the -p switch, but I thought it wouldn't work out. Essentially, is there an alternative way to remove all the empty directories under the parent directory? Thanks in advance! #!/bin/bash HOST='<hostname>' USER='<username>' DIR='<destination directory>' SOURCE='/srv/torrents/' rsync -e "ssh -l $USER" --remove-source-files -h -4 -r --stats -m --progress -i $SOURCE $HOST:$DIR find $SOURCE -mindepth 1 -type d -empty -prune -exec rmdir -p \{\} \;

  Read the article

• Identifying test machines in analytics logs

  - by RTigger

  We're just beginning to add analytics to our SaaS application, to begin (among other things) billing clients based on usage. The problem we're running into is there's a few circumstances where our support team will simulate a log in into production to try to reproduce reported issues with a client's configuration. When they log in, an entry will be made into our analytics logs that their specific account has logged in, which we use to calculate billing. A few ideas we had to solve this: 1) We log IP addresses as well as machine keys for each PC that logs in - we could filter out known IP addresses and/or machine keys belonging to support. The drawback is we have to maintain a list of keys / addresses manually. 2) If support (or anyone else internal) runs our application in debug mode (as opposed to release), it will not report analytics. This is fine, as long as support / anyone else remembers to switch to debug mode. 3) Include some sort of reg key / similar setting required to be set when configuring a production system in order to send analytics. Again, fine, as long as our infrastructure team remembers to set the reg key or setting. All of these approaches require some sort of human involvement, which we all know can be iffy at best. Has anyone run into a similar situation? Is there an automated approach to this problem? (PS Of course, we shouldn't be testing in production, but there are a few one-off instances with customer set up that we can't reproduce without logging in as them in production. This is the only time we do so, and this is the case I'm talking about in this question.)

  Read the article

< Previous Page | 241 242 243 244 245 246 247 248 249 250 251 252  | Next Page >