Search Results

Search found 13082 results on 524 pages for 'ip camera'.

Page 246/524 | < Previous Page | 242 243 244 245 246 247 248 249 250 251 252 253  | Next Page >

  • Use two networks at the same time?

    - by Christopher
    I want to use Ubuntu 10.10 Server in a classroom, a computer lab whose bandwidth is provided by a local cable ISP. That's no problem, though the school network has an IP printer that I want to use. I cannot reach the printer through the cable Internet. But, I have two network cards. How is it possible to use both networks at once? eth0 (static 192.168.1.254) is plugged into a four-port router, 192.168.1.1. On the public side of the four-port router is Internet provided by the cable company. I also have the classroom workstations plugged into a switch. The switch is plugged into the four-port router. The whole classroom is wired into the cable Internet. The other NIC, eth1, could it be plugged into an Ethernet jack in the wall? It uses the school network, and I might receive by DHCP an IP address like 10.140.10.100, with the printer on maybe 10.120.50.10. I was thinking about installing the printer on the server so that it could be shared with the workstations. But how does this work? Can I just plug eth1 into the school network and access both LANs? Thanks for any insight

    Read the article

  • Network: Incoming connections work, outgoing fails

    - by anirvan
    i recently set up my own server at home to run Ubuntu 12.04 server ed. on booting up, i noticed that a message related to networking comes up, and the booting process pauses. the message read something like - waiting for network configuration and after a while - waiting another 60 seconds... on booting up, I realised that any command which requires a network connection was not working - ping, apt-get install, etc. on firing the ifup eth0 command, I get the error RTNETLINK answers: File exists. Failed to bring up eth0. I also realised, while searching the web for this problem, that this is probably one of the most common networking related issues - however, most of the questions are around setting up multiple IPs for the same machine. ifdown eth0 also fails, stating that eth0 is not configured. my /etc/network/interfaces file has a simple configuration for a static IP: auto lo iface lo inet loopback auto eth0 iface eth0 inet static address xx.xx.xx.xx netmask xx.xx.xx.xx broadcast xx.xx.xx.xx gateway xx.xx.xx.xx dns-nameservers xx.xx.xx.xx The strangest part of this problem is that, while I can't connect to anything outside, I can ping to this particular server using the static IP configured in the interface file, and, i can even SSH into it! I'm really at ends here with this problem, and any guidance is much appreciated. Thanks!

    Read the article

  • Best design for a "Command Executer" class

    - by Justin984
    Sorry for the vague title, I couldn't think of a way to condense the question. I am building an application that will run as a background service and intermittently collect data about the system its running on. A second Android controller application will query the system over tcp/ip for statistics about the system. Currently, the background service has a tcp listener class that reads/writes bytes from a socket. When data is received, it raises an event to notify the service. The service takes the bytes, feeds them into a command parser to figure out what is being requested, and then passes the parsed command to a command executer class. When the service receives a "query statistics" command, it should return statistics over the tcp/ip connection. Currently, all of these classes are fully decoupled from each other. But in order for the command executer to return statistics, it will obviously need access to the socket somehow. For reasons I can't completely articulate, it feels wrong for the command executer to have a direct reference to the socket. I'm looking for strategies and/or design patterns I can use to return data over the socket while keeping the classes decoupled, if this is possible. Hopefully this makes sense, please let me know if I can include any info that would make the question easier to understand.

    Read the article

  • A new clients come into my web agency. How to configure email and social accounts to work better? [on hold]

    - by Marco Panichi
    I created websites for many years but still have not found the right way to organize all the email and social accounts of every clients. I mean, every web agency follows dozens of customers. Each client needs at least Google Analytics, AdWords, a Facebook page, a Twitter profile, a Youtube channel, probably a listing on Google Places and maybe a Mail Chimp (or similar) account. The web agency, in my opinion, must own these accounts, use them to deliver results to the customer and -of course- make them available to the customer for two reasons: - The customer must be able to see how things are going - The client must have the ability to change web agency without suffering The web agency, however, has many problems in having all of these accounts. For example, I like the idea of having a Gmail account for each client and from that account use all the products of Google. But is not possible to create more than many Gmail account from the same ip address and with the same phone number. The web agency could invite the customer to create his own accounts but: - This is not necessary a value for the customer (indeed...) - The web agency would manage them, however, from the same ip address, incurring in problems - If phone verification occurs, the web agency has to disturb the customer for verification Have you the same problem? How to solve it?

    Read the article

  • Processing Kinect v2 Color Streams in Parallel

    - by Chris Gardner
    Originally posted on: http://geekswithblogs.net/freestylecoding/archive/2014/08/20/processing-kinect-v2-color-streams-in-parallel.aspxProcessing Kinect v2 Color Streams in Parallel I've really been enjoying being a part of the Kinect for Windows Developer's Preview. The new hardware has some really impressive capabilities. However, with great power comes great system specs. Unfortunately, my little laptop that could is not 100% up to the task; I've had to get a little creative. The most disappointing thing I've run into is that I can't always cleanly display the color camera stream in managed code. I managed to strip the code down to what I believe is the bear minimum: using( ColorFrame _ColorFrame = e.FrameReference.AcquireFrame() ) { if( null == _ColorFrame ) return;   BitmapToDisplay.Lock(); _ColorFrame.CopyConvertedFrameDataToIntPtr( BitmapToDisplay.BackBuffer, Convert.ToUInt32( BitmapToDisplay.BackBufferStride * BitmapToDisplay.PixelHeight ), ColorImageFormat.Bgra ); BitmapToDisplay.AddDirtyRect( new Int32Rect( 0, 0, _ColorFrame.FrameDescription.Width, _ColorFrame.FrameDescription.Height ) ); BitmapToDisplay.Unlock(); } With this snippet, I'm placing the converted Bgra32 color stream directly on the BackBuffer of the WriteableBitmap. This gives me pretty smooth playback, but I still get the occasional freeze for half a second. After a bit of profiling, I discovered there were a few problems. The first problem is the size of the buffer along with the conversion on the buffer. At this time, the raw image format of the data from the Kinect is Yuy2. This is great for direct video processing. It would be ideal if I had a WriteableVideo object in WPF. However, this is not the case. Further digging led me to the real problem. It appears that the SDK is converting the input serially. Let's think about this for a second. The color camera is a 1080p camera. As we should all know, this give us a native resolution of 1920 x 1080. This produces 2,073,600 pixels. Yuy2 uses 4 bytes per 2 pixel, for a buffer size of 4,147,200 bytes. Bgra32 uses 4 bytes per pixel, for a buffer size of 8,294,400 bytes. The SDK appears to be doing this on one thread. I started wondering if I chould do this better myself. I mean, I have 8 cores in my system. Why can't I use them all? The first problem is converting a Yuy2 frame into a Bgra32 frame. It is NOT trivial. I spent a day of research of just how to do this. In the end, I didn't even produce the best algorithm possible, but it did work. After I managed to get that to work, I knew my next step was the get the conversion operation off the UI Thread. This was a simple process of throwing the work into a Task. Of course, this meant I had to marshal the final write to the WriteableBitmap back to the UI thread. Finally, I needed to vectorize the operation so I could run it safely in parallel. This was, mercifully, not quite as hard as I thought it would be. I had my loop return an index to a pair of pixels. From there, I had to tell the loop to do everything for this pair of pixels. If you're wondering why I did it for pairs of pixels, look back above at the specification for the Yuy2 format. I won't go into full detail on why each 4 bytes contains 2 pixels of information, but rest assured that there is a reason why the format is described in that way. The first working attempt at this algorithm successfully turned my poor laptop into a space heater. I very quickly brought and maintained all 8 cores up to about 97% usage. That's when I remembered that obscure option in the Task Parallel Library where you could limit the amount of parallelism used. After a little trial and error, I discovered 4 parallel tasks was enough for most cases. This yielded the follow code: private byte ClipToByte( int p_ValueToClip ) { return Convert.ToByte( ( p_ValueToClip < byte.MinValue ) ? byte.MinValue : ( ( p_ValueToClip > byte.MaxValue ) ? byte.MaxValue : p_ValueToClip ) ); }   private void ColorFrameArrived( object sender, ColorFrameArrivedEventArgs e ) { if( null == e.FrameReference ) return;   // If you do not dispose of the frame, you never get another one... using( ColorFrame _ColorFrame = e.FrameReference.AcquireFrame() ) { if( null == _ColorFrame ) return;   byte[] _InputImage = new byte[_ColorFrame.FrameDescription.LengthInPixels * _ColorFrame.FrameDescription.BytesPerPixel]; byte[] _OutputImage = new byte[BitmapToDisplay.BackBufferStride * BitmapToDisplay.PixelHeight]; _ColorFrame.CopyRawFrameDataToArray( _InputImage );   Task.Factory.StartNew( () => { ParallelOptions _ParallelOptions = new ParallelOptions(); _ParallelOptions.MaxDegreeOfParallelism = 4;   Parallel.For( 0, Sensor.ColorFrameSource.FrameDescription.LengthInPixels / 2, _ParallelOptions, ( _Index ) => { // See http://msdn.microsoft.com/en-us/library/windows/desktop/dd206750(v=vs.85).aspx int _Y0 = _InputImage[( _Index << 2 ) + 0] - 16; int _U = _InputImage[( _Index << 2 ) + 1] - 128; int _Y1 = _InputImage[( _Index << 2 ) + 2] - 16; int _V = _InputImage[( _Index << 2 ) + 3] - 128;   byte _R = ClipToByte( ( 298 * _Y0 + 409 * _V + 128 ) >> 8 ); byte _G = ClipToByte( ( 298 * _Y0 - 100 * _U - 208 * _V + 128 ) >> 8 ); byte _B = ClipToByte( ( 298 * _Y0 + 516 * _U + 128 ) >> 8 );   _OutputImage[( _Index << 3 ) + 0] = _B; _OutputImage[( _Index << 3 ) + 1] = _G; _OutputImage[( _Index << 3 ) + 2] = _R; _OutputImage[( _Index << 3 ) + 3] = 0xFF; // A   _R = ClipToByte( ( 298 * _Y1 + 409 * _V + 128 ) >> 8 ); _G = ClipToByte( ( 298 * _Y1 - 100 * _U - 208 * _V + 128 ) >> 8 ); _B = ClipToByte( ( 298 * _Y1 + 516 * _U + 128 ) >> 8 );   _OutputImage[( _Index << 3 ) + 4] = _B; _OutputImage[( _Index << 3 ) + 5] = _G; _OutputImage[( _Index << 3 ) + 6] = _R; _OutputImage[( _Index << 3 ) + 7] = 0xFF; } );   Application.Current.Dispatcher.Invoke( () => { BitmapToDisplay.WritePixels( new Int32Rect( 0, 0, Sensor.ColorFrameSource.FrameDescription.Width, Sensor.ColorFrameSource.FrameDescription.Height ), _OutputImage, BitmapToDisplay.BackBufferStride, 0 ); } ); } ); } } This seemed to yield a results I wanted, but there was still the occasional stutter. This lead to what I realized was the second problem. There is a race condition between the UI Thread and me locking the WriteableBitmap so I can write the next frame. Again, I'm writing approximately 8MB to the back buffer. Then, I started thinking I could cheat. The Kinect is running at 30 frames per second. The WPF UI Thread runs at 60 frames per second. This made me not feel bad about exploiting the Composition Thread. I moved the bulk of the code from the FrameArrived handler into CompositionTarget.Rendering. Once I was in there, I polled from a frame, and rendered it if it existed. Since, in theory, I'm only killing the Composition Thread every other hit, I decided I was ok with this for cases where silky smooth video performance REALLY mattered. This ode looked like this: private byte ClipToByte( int p_ValueToClip ) { return Convert.ToByte( ( p_ValueToClip < byte.MinValue ) ? byte.MinValue : ( ( p_ValueToClip > byte.MaxValue ) ? byte.MaxValue : p_ValueToClip ) ); }   void CompositionTarget_Rendering( object sender, EventArgs e ) { using( ColorFrame _ColorFrame = FrameReader.AcquireLatestFrame() ) { if( null == _ColorFrame ) return;   byte[] _InputImage = new byte[_ColorFrame.FrameDescription.LengthInPixels * _ColorFrame.FrameDescription.BytesPerPixel]; byte[] _OutputImage = new byte[BitmapToDisplay.BackBufferStride * BitmapToDisplay.PixelHeight]; _ColorFrame.CopyRawFrameDataToArray( _InputImage );   ParallelOptions _ParallelOptions = new ParallelOptions(); _ParallelOptions.MaxDegreeOfParallelism = 4;   Parallel.For( 0, Sensor.ColorFrameSource.FrameDescription.LengthInPixels / 2, _ParallelOptions, ( _Index ) => { // See http://msdn.microsoft.com/en-us/library/windows/desktop/dd206750(v=vs.85).aspx int _Y0 = _InputImage[( _Index << 2 ) + 0] - 16; int _U = _InputImage[( _Index << 2 ) + 1] - 128; int _Y1 = _InputImage[( _Index << 2 ) + 2] - 16; int _V = _InputImage[( _Index << 2 ) + 3] - 128;   byte _R = ClipToByte( ( 298 * _Y0 + 409 * _V + 128 ) >> 8 ); byte _G = ClipToByte( ( 298 * _Y0 - 100 * _U - 208 * _V + 128 ) >> 8 ); byte _B = ClipToByte( ( 298 * _Y0 + 516 * _U + 128 ) >> 8 );   _OutputImage[( _Index << 3 ) + 0] = _B; _OutputImage[( _Index << 3 ) + 1] = _G; _OutputImage[( _Index << 3 ) + 2] = _R; _OutputImage[( _Index << 3 ) + 3] = 0xFF; // A   _R = ClipToByte( ( 298 * _Y1 + 409 * _V + 128 ) >> 8 ); _G = ClipToByte( ( 298 * _Y1 - 100 * _U - 208 * _V + 128 ) >> 8 ); _B = ClipToByte( ( 298 * _Y1 + 516 * _U + 128 ) >> 8 );   _OutputImage[( _Index << 3 ) + 4] = _B; _OutputImage[( _Index << 3 ) + 5] = _G; _OutputImage[( _Index << 3 ) + 6] = _R; _OutputImage[( _Index << 3 ) + 7] = 0xFF; } );   BitmapToDisplay.WritePixels( new Int32Rect( 0, 0, Sensor.ColorFrameSource.FrameDescription.Width, Sensor.ColorFrameSource.FrameDescription.Height ), _OutputImage, BitmapToDisplay.BackBufferStride, 0 ); } }

    Read the article

  • Diskless with Ubuntu 12.04

    - by user139462
    I'm trying to setup a new diskless solution with ubuntu 12.04 without any success. I followed this howto: https://help.ubuntu.com/community/DisklessUbuntuHowto But the initramfs seems not to be able to mount my nfs share. On my server side: My /etc/exports /srv/nfs4 192.168.0.0/24(fsid=0,rw,no_subtree_check) /srv/nfs4/nfsroot 192.168.0.0/24(rw,no_root_squash,no_subtree_check,fsid=1,nohide,insecure,sync) I'm able to mount my nfs share on standard Ubuntu installation without any problem. I can mount my nfs on any client with those commands: mount 192.168.0.3:/nfsroot /mnt or mount 192.168.0.3:/srv/nfs4/nfsroot /mnt My /tftpboot/pxelinux.cfg/default config file is DEFAULT vmlinuz-3.5.0-25-generic root=/dev/nfs initrd=initrd.img-3.5.0-25-generic nfsroot=192.168.0.3:/nfsroot ip=dhcp rw I also tried DEFAULT vmlinuz-3.5.0-25-generic root=/dev/nfs initrd=initrd.img-3.5.0-25-generic nfsroot=192.168.0.3:/srv/nfs4/nfsroot ip=dhcp rw. What I got in initramfs: With the setting [nfsroot=192.168.0.3:/nfsroot] Diskless output: mount call failed - server replied: Permission denied On Syslog of my nfs server: rpc.mountd[1266]: refused mount request from 192.168.0.10 for /nfsroot (/): not exported With the setting [nfsroot=192.168.0.3:/srv/nfs4/nfsroot] Diskless output: mount: the kernel lacks NFS v3 support On Syslog of my nfs server I got: Mar 11 14:03:06 BootFromLan rpc.mountd[1266]: authenticated mount request from 192.168.0.10:834 for /srv/nfs4/nfsroot (/srv/nfs4/nfsroot) Mar 11 14:03:06 BootFromLan rpc.mountd[1266]: refused unmount request from 192.168.0.10 for /root (/): not exported

    Read the article

  • Bizarre SSH Problem - It won't even start

    - by thallium85
    I recently got Ubuntu 12.04 Precise, got it up and running with some MediaWiki software, static IP on the box and router and was able to access the main page even from a cell phone. Everything seemed great... Then I wanted to finally get rid of the monitor and keyboard and login remotely via SSH. I installed openssh-server, let everything point to port 22 for a test run and installed putty on my Windows XP machine. I got a connection refused. Went back and started checking the Ubuntu install itself... (I'm under root from this point on) $ sudo -s $ service ssh status ssh stop/waiting $ service ssh start ssh start/running, process 2212 $ service ssh status ssh stop/waiting Apparently ssh has stopped or is waiting for something.... $ ssh localhost ssh: connect to host localhost port 22: Connection refused I can't even connect to myself... I checked ufw (firewall) to see if port 22 is doing alright... $ sudo ufw status Status: active To Action From 22 ALLOW Anywhere 22/tcp ALLOW Anywhere 22 ALLOW Anywhere (v6) 22/tcp ALLOW Anywhere (v6) sshd_config shows only Port 22 Is ssh not using the right IP address at all? I just don't get what I did wrong here. When this is up and running I will def change the port number, but for now, I don't want to mess with the default install too much until a test run with putty is successful. Edit: Here are my sshd_config file and my ssh_config file. The command /usr/sbin/sshd -p 22 -D -d -e returns: /etc/ssh/sshd_config line 159: Subsystem 'sftp' already defined. Edit: @phoibus moving the sshd_config file and reinstalling did the trick! service ssh status the above command shows that ssh is now running and I am now able to log in from my windows xp computer remotely via putty. Thanks so much! I can now use my monitor for other things!

    Read the article

  • Discovery methods

    - by Owen Allen
    In Ops Center, asset discovery is a process in which the software determines what assets exist in your environment. You can't monitor an asset, or do anything to it through Ops Center, until it's discovered. I've seen a couple of questions about how to discover various types of asset, so I thought I'd explain the discovery methods and what they each do. Find Assets - This discovery method searches for service tags on all known networks. Service tags are small files on some hardware and operating systems that provide basic identification info. Once a service tag has been found, you provide credentials to manage the asset. This method can discover assets quickly, but only if the target assets have service tags. Add Assets with discovery profile - This method lets you specify targets by providing IP addresses, IP ranges, or hostnames, as well as the credentials needed to connect to and manage these assets. You can create discovery profiles for any type of asset. Declare asset - This method lets you specify the details of a server, with or without a configured service processor. You can then use Ops Center to install a new operating system or configure the SP. This method works well for new hardware. These methods are all discussed in more detail in the Asset Management chapter of the Feature Reference guide.

    Read the article

  • custom domain point to tumblr blog

    - by Julius
    My domain mydomain.com is registered with godaddy. I wish to host my tumblr blog on this domain with nearlyfreespeech.net hosting. My active nameservers at godaddy already point to my authoritative ones at NFS.net which is working. However i'm baffled of the correct configuration to set to point to my Tumblr. Preferably id like (A) my domain http://mydomain.com to host the blog and have http://www.mydomain.com redirect also to http://mydomain.com If this is too difficult my next preference is (B) to have http://www.mydomain.com host the blog whilst http://mydomain.com redirects to http://www.mydomain.com My 3rd preference is to have (C) a sub-domain like http://tumblr.mydomain.com or http://tumblr.mydomain.com to host the blog and i guess have http://mydomain.com and http://www.mydomain.com both redirect to it. I've tried having two aliases mydomain.com and www.mydomain.com pointing to my permanent NFS ip at mydomain.nfshost.com and when i try to add: (1) an A record pointing mydomain.com to the ip 66.6.44.4 as per Tumblr's instructions it tells me i already have the bare domain as an alias so i cant do that. (2) the A record on the www.mydomain.com alias. I can do this with either www.mydomain.com set as an alias or not. But when i tried this with mydomain.com set as the canonical name the result when visiting either mydomain.com or www.mydomain.com was them both continually redirecting to eachother until an error was thrown. So i was wondering if there is a ninja that could save me some hairpulling and tell me the correct way to config A, or else B, or else C.

    Read the article

  • Dedicated server: managed hosting or manage it myself?

    - by ddawber
    We're currently hosting a number of sites on a self-managed dedicated server. Some companies, however, offer a managed dedicated server hosting service. They offer: Roughly the same server spec Ticketing system support Managed daily backups Virtual firewall (but with a limit of 10 IP addresses allowed through at any one time) Now, this managed hosting is at extra expense - somewhere in the region of $500 per month, and the limit on the number of IP addresses they'll manage on the firewall is also a real pain. My thinking is it would be better and cheaper to Stay with the same host since the dedicated box is fine Get an Amazon AWS account and use their server to manage backups; there are a number of good tools that can be used to automate the process Configure iptables so that I have complete control of the firewall I want to know Is a managed virtual firewall likely to be more secure than me configuring iptables? Whether, in your opinion, it's best to let someone else take care of backups? If, from your experience, there's anything else i'm missing that warrants using managed hosting over a DIY service? I think there is some reluctance to not having managed hosting since a managed host in effect takes responsibility for your server, whereas any hardware or security issues with a server that we manage would mean we are forced to hold our hands up when a client site goes down. That said, I personally don't think a managed host does that much in the day to day running of your server (backups are automatic, OS updates are carried out with ease, etc.).

    Read the article

  • Dedicated server: managed hosting or manage it myself?

    - by ddawber
    We're currently hosting a number of sites on a self-managed dedicated server. Some companies, however, offer a managed dedicated server hosting service. They offer: Roughly the same server spec Ticketing system support Managed daily backups Virtual firewall (but with a limit of 10 IP addresses allowed through at any one time) Now, this managed hosting is at extra expense - somewhere in the region of $500 per month, and the limit on the number of IP addresses they'll manage on the firewall is also a real pain. My thinking is it would be better and cheaper to Stay with the same host since the dedicated box is fine Get an Amazon AWS account and use their server to manage backups; there are a number of good tools that can be used to automate the process Configure iptables so that I have complete control of the firewall I want to know Is a managed virtual firewall likely to be more secure than me configuring iptables? Whether, in your opinion, it's best to let someone else take care of backups? If, from your experience, there's anything else i'm missing that warrants using managed hosting over a DIY service? I think there is some reluctance to not having managed hosting since a managed host in effect takes responsibility for your server, whereas any hardware or security issues with a server that we manage would mean we are forced to hold our hands up when a client site goes down. That said, I personally don't think a managed host does that much in the day to day running of your server (backups are automatic, OS updates are carried out with ease, etc.).

    Read the article

  • 64kb limit on the size of MSMQ Multicast Messages

    - by John Breakwell
    When Windows 2003 came out, Microsoft introduced the ability to broadcast messages to any machines that were listening back. All you had to do was send out a message on a particular port and IP address and any client that had set up a Multicast queue with matching port and IP address would get a copy. Since its introduction, there have been a couple of security vulnerabilities that needed to be removed: Microsoft Security Bulletin MS06-052 Vulnerability in Pragmatic General Multicast (PGM) Could Allow Remote Code Execution (919007) Microsoft Security Bulletin MS08-036 Vulnerabilities in Pragmatic General Multicast (PGM) could allow denial of service (950762) The second of these, MS08-036, was resolved through an undocumented change in functionality. Basically, a limit of 64kb was put on the maximum size of a message that could be broadcast using the Multicast method. Obviously this has caused a few problems for any existing MSMQ Multicast applications that expected to be able to send larger messages. A hotfix has been developed to resolve this problem. 961605 FIX: Multicast messages larger than 64 kilobytes (KB) are not delivered as expected by using Message Queuing 3.0 after security update MS08-036 is installed A registry change is required: Open the registry with Regedit Navigate to HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\RMCAST\Parameters\ Create a DWord called MaxpacketSize Set the value to the desired number of bytes. You can set it to a value between zero and 4MB. If you specify anything above 4MB, it will default to 64K. A reboot is needed after adding this value.

    Read the article

  • ISP issue browsing "sonos.com" - need to diagnose and prove [closed]

    - by john
    I am unable to browse to a website "sonos.com" with my ISP (virgin). I have ruled out browsers, PCs, macs, routers, wifi, etc. Other ISPs (even other virgin connections in different areas!) supply this site no problem. I am 99% convinced there is a DNS issue lurking here. There is something fishy about the DNS for the site : What I notice is that online DNS sites tell me the right IP address for "sonos.com", but not for "www.sonos.com". Anyway when I type "sonos.com" the browser (any/all of the 4 I tried) fail to display the page. Firefox gives a "connection was reset" error. If I browse to sonos.com using the IP address it works OK. Browsing to www.sonos.com or sonos.com works fine with other ISPs of course. Questions: 1 Does anyone have any idea what might be going on here? 2 Any suggestions as to tools/monitors to help investigate/prove what is going on I can then take this up with virgin and/or sonos. Thanks

    Read the article

  • How to enable a Web portal-based rich enterprise platform on different domains and hosts using JS without customization/ server configuration

    - by S.Jalali
    Our company Coscend has built a Web portal-based communications and cloud collaboration platform by using JavaScript (JS), which is embedded in HTML5 and formatted with CSS3. Other technologies used in the core code include Flash, Flex, PostgreSQL and MySQL. Our team would like to host this platform on five different Windows and Linux environments that run different types of Web servers such as IIS and Apache. Technical challenge: Each of these Windows and Linux servers have a different host name and domain name (and IP address), but we would like to keep our enterprise platform independent of host server configuration. Possible approach to solution: We think an API (interface module with a GUI) is needed to accomplish this level of modularity and flexibility while deploying at our enterprise customers. Seeking your insights: In this context, our team would appreciate your guidance on: Is there an algorithmic method to implement this Web portal-based platform in these Windows and Linux environments while separating it from server configuration, i.e., customizing the host name, domain name and IP address for each individual instance? For example, would it be suitable to create some JS variables / objects for host name and domain name and call them in the different implementations? If a reference to the host/domain names occurs on hundreds of portal modules, these variables or JS objects would replace that. If so, what is the best way to make these object modules written in JS portable and re-usable across different environments and instances for enterprise customers? Here is an example of the implemented code for the said platform. The following Web site (www.CoscendCommunications.com) was built using this enterprise collaboration platform and has the base code examples of the platform. This Web site is domain-specific. We like to make the underlying platform such that it is domain and host-independent. This will allow the underlying platform to be deployed in multiple instances of our enterprise customers.

    Read the article

  • ubuntu 12.10 Lenovo b570e, WiFi connected but not working

    - by koogee
    I'm running ubuntu 12.10 liveUSB on a lenovo b570e. It has an atheros wifi card that connects with my home network but I can't browse AT ALL. My network is multiple clients --> router --> isp modem --> Internet I can ping my router (192.168.0.1) but not my isp's modem(192.168.15.1). I have 3 other computers connected to the same router that are working fine (infact i'm posting from one) ping -c 3 google.com unknown host google.com ping -c 3 8.8.8.8 shows 100% packet loss I think its some networking issue. I tried directly connecting it to the router via ethernet cable but same issue. It gets an ip, shows LAN connected but can't browse. If I connect it directly to the isp modem via ethernet cable it starts working fine. Connection Information shows: Interface: 802.11 wifi (wlan0) driver: ath9k security: wpa/wpa2 speed: 150mb/s ip: 192.168.0.106 broadcast: 192.168.0.255 subnet:255.255.255.0 default route: 192.168.0.1 primary dns: 192.168.15.1 i have restarted the router and modem many times. Rebooted the LiveUSB many times.

    Read the article

  • Strange traffic on fresh Ubuntu Server install

    - by Fishy
    I've just installed Ubuntu Server on my home box after becoming partially familiar with it at work and wanting to train up as a Pen Tester. I installed the latest version on a logical partition (the main one contained Win7), and selected none of the extra modules (I think). I installed ngrep and fired it up (along with TCPdump) and immediately saw some strange traffic which I am unable to identify. My pc is sending out UDP packets every couple of seconds to a seemingly random series of IP addresses, all on the same port (47669 - though I did also see it use another port for a while). I watched it do this for about 20 mins, whilst trying to work out why it was doing it. The only other traffic was the odd ARP request for the router and SSDP UPnP broadcasts from the router. Anyone know what this is, or have any advice on how best to find out? Thanks. EDIT: Actually, it's not my box generating the traffic. It's receiving the traffic on that port, from a series of IP addresses, and returning 'port unreachable' messages.

    Read the article

  • Kubuntu 11.10 Lot of Networking problems

    - by Cobraone
    Since I upgrade to 11.10 I have a lot of problems with KDE. First of all there are problems in configuring a static IP address. Just to explain @home I have a normal fiber ADSL and I use a DHCP. When I go to a customer I must insert a static IP address. With ifconfig everything seems ok but there is something wrong in searching DNS names. (I have installed Ubuntu and was going ok again). Now I Have reinstalled again Kubuntu 11.10 and I have the same problem in addition today I have discovered that if I connect to a network in another customer office the desktop freezes and I could only switch between windows with alt+tab. No FN key or right click to open run command works. So i unplugged network (configuration is just DHCP here) and tried on another position in office. It was the same. My Laptop freezes when connected, a fedora 14 of a friend works. So I decided to connect my Galaxy S II as USB network device. Everything is ok for like 3 minutes. When I noticed a little loss of signal again the desktop freezes and i must work (like now) just switching between windows with alt+tab). Additional information: Unplugging network or restarting it via Konsole does not not solve the freezing problem. Every time I must open a console and reboot. Any idea of what tests to do ? Just a recommendation: If I must post here logs or something else please guide me. I use Linux since Ubuntu 9 but I am not an "expert".

    Read the article

  • Can't connect nonlocally after 12.10 upgrade

    - by user101815
    I've just upgraded one of my systems from 12.04 to 12.10. Now I can't connect on that system beyond my local network. Connections within the local network seem to work fine, and I can make nonlocal connections from other machines (like the one I'm asking this question from). I suspect that some routing information has been messed up, but I don't know where to look for it. It's not a nameserver problem -- pinging outside sites by their IP addresses doesn't work either. I have another laptop next to this one, also running Kubuntu 12.10. On the one that can't connect, arp produces no output. On the other one, it produces 192.168.0.1 ether 00:23:69:fa:ce:ae C wlan0 On the working machine, the output of netstat starts with some tcp entries. On the nonworking one, those entries are absent. I asked this question on the Ubuntu forum but haven't gotten any answers there. One further complication: since the troublesome machine has no outside connection, it's extremely difficult to download anything to it. For what it's worth, "ping 8.8.8.8" produces "connect: Network is unreachable". Update: after a lot of fiddling, I have my external world back. I don't know what the key action was, but the first indication of progress was that "ping 8.8.8.8" worked. At that point I still didn't have a working nameserver, so external URLs didn't work. But I did this (based on an online post, of course): sudo dpkg-reconfigure resolvconf and answered Yes to all prompts. That did the trick!! Apparently my problem was unique, or close to it, since I couldn't find any online references to it: local net working, remote net not working, including explicit IP addresses. So I suppose that if no one else has this problem, no one cares about the solution!!

    Read the article

  • networking without port forwarding

    - by Wallacoloo
    I'm trying to add networking functionality to my game. I want any user to be able to host the game, and anyone to be able to connect as a client. The client sends info to the host about their player's position, etc. When the host receives a message, it validates it and then broadcasts it to its other clients. I will primarily be dealing with UDP, but will also need TCP for chat & lobby stuff. The problem is that I can't seem to get a packet sent from the client to the host or the other way around without enabling port forwarding on my router. But I don't think this is necessary. I believe the reason I need port forwarding is because I want to send a packet from 1 computer on a LAN to another computer on a different LAN, but neither of them have a global ip address since they're in a LAN. So really, I can only send packets targeting the other network's router, which must forward it on to the machine I want to reach. So how can I do this without port forwarding? Somehow a web server can communicate with my computer, which doesn't have a global ip, without port forwarding. And I've played plenty of multi-player games that don't require me to enable port forwarding. So it must be possible. Btw, I'm using SDL_Net. I don't think this will change anything though.

    Read the article

  • Extended service set help [closed]

    - by Cygnus X
    Sorry, this is going to be long and rambly. So, at home my network is set up as such: I have a "master router" that handles DHCP, from there I have a basic 5 port switch, and coming off that, I have a second router that I put in access point mode so that I could have better wireless coverage in my house. I cant seem to access it through a web browser since the master router kicked in and assigned it an ip address. But, i told you all that story, so that i could tell you this story. At the company I work for, they are trying to set up wireless cameras, according to the manual for these, in order to connect these cameras to our network, we need to get into the wireless router and associate the router with the cameras, but the problem is, the network is setup like my home network. Theres a "master router" which is a windows 2003 server, and then a wireless router in AP mode dishing out wireless access. I cant get into the router (by the way I'm not the system admin for the company, nor do i know jack squat about windows server , nor can I easily get in contact with the system admin. (quite the cluster f*k, eh?)) I've tried using wireshark to find the routers ip, dug through arp tables, tried plugging straight into the router, but I cant seem to get into the damn thing. Any ideas/suggestions would be greatly appreciated.

    Read the article

  • General website publishing questions involving domain forwarding issue

    - by Gorgeousyousuf
    Even though I have been having a certain level of knowledge and experience about web development I have never interested in obtaining a domain and publishing a website from my own server. Since today I have been struggling with getting my own domain and configuring it utilizing web sources. I started with learning the outline of web publishing process including web server installation, deploying a website for testing purpose,router port forwarding, getting a domain and forwarding domain to my router which will also forward http requests to my web server I am confused about some parts and so far could not get the web site accessed from outside of the network. All I try to do is just for learning purpose so I do not pay much attention to security issues for now. I have Server 2008 and IIS 7.5 installed. I use a laptop and have access to the modem over wireless and my modem is Zoom x6 5590. Well I will continue explaining what I have done so far and what I think will be after each action I did, I have successfully had access to my website on any local computer entering the internal ip address and port pair of the host machine in a browser. Next, I forwarded port 80 of my host machine creating a virtual server like 10.0.0.x(internal ip(static) of the host) - tcp - start port : 80 - end port : 80 in router options. Now I suppose every request that will come to the public Ip on port 80 will be forwarded to my host machine(10.0.0.x) over port 80. So If everyhing went as desired, the website listening on port 80 will accept the request and process the issue and finally respond bla bla bla... I suppose to access my website from outside of the network by entering http://MyPublicIp:80 in a browser but I couldn't accomplish this task by now despite using godady's domain forwarding tool,I see a small view of my website when I click the "preview" button that checks whether the address(http://publicip/Index.aspx) I entered where my domain will be forwarded is available or not. I am sure that configuring domain does not play a role in solving such a problem since using public ip and port matching does not help. So here is the first question, What is the fact that I face this problem? After that, I have couple of question regarding domain forwarding using godaddy tool. Can I forward my domain to a any port for example port 8080 other than default http port 80? Additionally, can I use a sub-domain to forward to a different port of the host? What I want to design is if the client enters www.mydomain.com, website1 will respond over a specified port and after when a client enters info.mydomain.com, another website which listens on different port will respond. I tried to add a sub-domain and forward it to a address like http://www.mydomain.com:8080/Index.aspx with no success. Can I really do that? Finally, what if I have a ftp site listening on the default port 21 and I create a domain like ftp.mydomain.com that will forward to that ftp site address. Is it possible to use sub-domains for ftp site access? I know I am more than confused but no matter whatever and however you reply to me, you will help me have a more clear view on this subject. Thank you very much from now.

    Read the article

  • Clipplanes, vertex shaders and hardware vertex processing in Direct3D 9

    - by Igor
    Hi, I have an issue with clipplanes in my application that I can reproduce in a sample from DirectX SDK (February 2010). I added a clipplane to the HLSLwithoutEffects sample: ... D3DXPLANE g_Plane( 0.0f, 1.0f, 0.0f, 0.0f ); ... void SetupClipPlane(const D3DXMATRIXA16 & view, const D3DXMATRIXA16 & proj) { D3DXMATRIXA16 m = view * proj; D3DXMatrixInverse( &m, NULL, &m ); D3DXMatrixTranspose( &m, &m ); D3DXPLANE plane; D3DXPlaneNormalize( &plane, &g_Plane ); D3DXPLANE clipSpacePlane; D3DXPlaneTransform( &clipSpacePlane, &plane, &m ); DXUTGetD3D9Device()->SetClipPlane( 0, clipSpacePlane ); } void CALLBACK OnFrameMove( double fTime, float fElapsedTime, void* pUserContext ) { // Update the camera's position based on user input g_Camera.FrameMove( fElapsedTime ); // Set up the vertex shader constants D3DXMATRIXA16 mWorldViewProj; D3DXMATRIXA16 mWorld; D3DXMATRIXA16 mView; D3DXMATRIXA16 mProj; mWorld = *g_Camera.GetWorldMatrix(); mView = *g_Camera.GetViewMatrix(); mProj = *g_Camera.GetProjMatrix(); mWorldViewProj = mWorld * mView * mProj; g_pConstantTable->SetMatrix( DXUTGetD3D9Device(), "mWorldViewProj", &mWorldViewProj ); g_pConstantTable->SetFloat( DXUTGetD3D9Device(), "fTime", ( float )fTime ); SetupClipPlane( mView, mProj ); } void CALLBACK OnFrameRender( IDirect3DDevice9* pd3dDevice, double fTime, float fElapsedTime, void* pUserContext ) { // If the settings dialog is being shown, then // render it instead of rendering the app's scene if( g_SettingsDlg.IsActive() ) { g_SettingsDlg.OnRender( fElapsedTime ); return; } HRESULT hr; // Clear the render target and the zbuffer V( pd3dDevice->Clear( 0, NULL, D3DCLEAR_TARGET | D3DCLEAR_ZBUFFER, D3DCOLOR_ARGB( 0, 45, 50, 170 ), 1.0f, 0 ) ); // Render the scene if( SUCCEEDED( pd3dDevice->BeginScene() ) ) { pd3dDevice->SetVertexDeclaration( g_pVertexDeclaration ); pd3dDevice->SetVertexShader( g_pVertexShader ); pd3dDevice->SetStreamSource( 0, g_pVB, 0, sizeof( D3DXVECTOR2 ) ); pd3dDevice->SetIndices( g_pIB ); pd3dDevice->SetRenderState( D3DRS_CLIPPLANEENABLE, D3DCLIPPLANE0 ); V( pd3dDevice->DrawIndexedPrimitive( D3DPT_TRIANGLELIST, 0, 0, g_dwNumVertices, 0, g_dwNumIndices / 3 ) ); pd3dDevice->SetRenderState( D3DRS_CLIPPLANEENABLE, 0 ); RenderText(); V( g_HUD.OnRender( fElapsedTime ) ); V( pd3dDevice->EndScene() ); } } When I rotate the camera I have different visual results when using hardware and software vertex processing. In software vertex processing mode or when using the reference device the clipping plane works fine as expected. In hardware mode it seems to rotate with the camera. If I remove the call to RenderText(); from OnFrameRender then hardware rendering also works fine. Further debugging reveals that the problem is in ID3DXFont::DrawText. I have this issue in Windows Vista and Windows 7 but not in Windows XP. I tested the code with the latest NVidia and ATI drivers in all three OSes on different PCs. Is it a DirectX issue? Or incorrect usage of clipplanes? Thanks Igor

    Read the article

  • C# need help debugging socks5-connection attemp

    - by Chuck
    Hi, I've written the following code to (successfully) connect to a socks5 proxy. I send a user/pw auth and get an OK reply (0x00), but as soon as I tell the proxy to connect to whichever ip:port, it gives me 0x01 (general error). Socket socket5_proxy = new Socket(AddressFamily.InterNetwork, SocketType.Stream, ProtocolType.Tcp); IPEndPoint proxyEndPoint = new IPEndPoint(IPAddress.Parse("111.111.111.111"), 1080); // proxy ip, port. fake for posting purposes. socket5_proxy.Connect(proxyEndPoint); byte[] init_socks_command = new byte[4]; init_socks_command[0] = 0x05; init_socks_command[1] = 0x02; init_socks_command[2] = 0x00; init_socks_command[3] = 0x02; socket5_proxy.Send(init_socks_command); byte[] socket_response = new byte[2]; int bytes_recieved = socket5_proxy.Receive(socket_response, 2, SocketFlags.None); if (socket_response[1] == 0x02) { byte[] temp_bytes; string socks5_user = "foo"; string socks5_pass = "bar"; byte[] auth_socks_command = new byte[3 + socks5_user.Length + socks5_pass.Length]; auth_socks_command[0] = 0x05; auth_socks_command[1] = Convert.ToByte(socks5_user.Length); temp_bytes = Encoding.Default.GetBytes(socks5_user); temp_bytes.CopyTo(auth_socks_command, 2); auth_socks_command[2 + socks5_user.Length] = Convert.ToByte(socks5_pass.Length); temp_bytes = Encoding.Default.GetBytes(socks5_pass); temp_bytes.CopyTo(auth_socks_command, 3 + socks5_user.Length); socket5_proxy.Send(auth_socks_command); socket5_proxy.Receive(socket_response, 2, SocketFlags.None); if (socket_response[1] != 0x00) return; byte[] connect_socks_command = new byte[10]; connect_socks_command[0] = 0x05; connect_socks_command[1] = 0x02; // streaming connect_socks_command[2] = 0x00; connect_socks_command[3] = 0x01; // ipv4 temp_bytes = IPAddress.Parse("222.222.222.222").GetAddressBytes(); // target connection. fake ip, obviously temp_bytes.CopyTo(connect_socks_command, 4); byte[] portBytes = BitConverter.GetBytes(8888); connect_socks_command[8] = portBytes[0]; connect_socks_command[9] = portBytes[1]; socket5_proxy.Send(connect_socks_command); socket5_proxy.Receive(socket_response); if (socket_response[1] != 0x00) MessageBox.Show("Damn it"); // I always end here, 0x01 I've used this as a reference: http://en.wikipedia.org/wiki/SOCKS#SOCKS_5 Have I completely misunderstood something here? How I see it, I can connect to the socks5 fine. I can authenticate fine. But I/the proxy can't "do" anything? Yes, I know the proxy works. Yes, the target ip is available and yes the target port is open/responsive. I get 0x01 no matter what I try to connect to. Any help is VERY MUCH appreciated! Thanks, Chuck

    Read the article

  • Variable mysteriously changing value

    - by Eitan
    I am making a simple tcp/ip chat program for practicing threads and tcp/ip. I was using asynchronous methods but had a problem with concurrency so I went to threads and blocking methods (not asynchronous). I have two private variables defined in the class, not static: string amessage = string.Empty; int MessageLength; and a Thread private Thread BeginRead; Ok so I call a function called Listen ONCE when the client starts: public virtual void Listen(int byteLength) { var state = new StateObject {Buffer = new byte[byteLength]}; BeginRead = new Thread(ReadThread); BeginRead.Start(state); } and finally the function to receive commands and process them, I'm going to shorten it because it is really long: private void ReadThread(object objectState) { var state = (StateObject)objectState; int byteLength = state.Buffer.Length; while (true) { var buffer = new byte[byteLength]; int len = MySocket.Receive(buffer); if (len <= 0) return; string content = Encoding.ASCII.GetString(buffer, 0, len); amessage += cleanMessage.Substring(0, MessageLength); if (OnRead != null) { var e = new CommandEventArgs(amessage); OnRead(this, e); } } } Now, as I understand it only one thread at a time will enter BeginRead, I call Receive, it blocks until I get data, and then I process it. The problem: the variable amessage will change it's value between statements that do not touch or alter the variable at all, for example at the bottom of the function at: if (OnRead != null) "amessage" will be equal to 'asdf' and at if (OnRead != null) "amessage" will be equal to qwert. As I understand it this is indicative of another thread changing the value/running asynchronously. I only spawn one thread to do the receiving and the Receive function is blocking, how could there be two threads in this function and if there is only one thread how does amessage's value change between statements that don't affect it's value. As a side note sorry for spamming the site with these questions but I'm just getting a hang of this threading story and it's making me want to sip cyanide. Thanks in advance. EDIT: Here is my code that calls the Listen Method in the client: public void ConnectClient(string ip,int port) { client.Connect(ip,port); client.Listen(5); } and in the server: private void Accept(IAsyncResult result) { var client = new AbstractClient(MySocket.EndAccept(result)); var e = new CommandEventArgs(client, null); Clients.Add(client); client.Listen(5); if (OnClientAdded != null) { var target = (Control) OnClientAdded.Target; if (target != null && target.InvokeRequired) target.Invoke(OnClientAdded, this, e); else OnClientAdded(this, e); } client.OnRead += OnRead; MySocket.BeginAccept(new AsyncCallback(Accept), null); } All this code is in a class called AbstractClient. The client inherits the Abstract client and when the server accepts a socket it create's it's own local AbstractClient, in this case both modules access the functions above however they are different instances and I couldn't imagine threads from different instances combining especially as no variable is static.

    Read the article

  • MediaElement not showing in custom 3D class

    - by user3271180
    I'm trying to display a videostream in a Viewport3d. When I add the MediaElement via xaml, the video plays without a problem; even when I add the video as ModelVisual3D in the code-behind, the video works. When I abstract the video into a class, however, the video stops appearing. This happens with both web and local video files. I tried compiling with both x86 and 64 bit. Any way to fix this behaviour? Why is this happening? I have the following viewport: <Viewport3D> <!-- Camera --> <Viewport3D.Camera> <PerspectiveCamera Position="0,0,100" LookDirection="0,0,-1" UpDirection="0,1,0" /> </Viewport3D.Camera> <!-- Light --> <ModelVisual3D> <ModelVisual3D.Content> <AmbientLight Color="White" /> </ModelVisual3D.Content> </ModelVisual3D> <!-- this doesn't work --> <mediaElementTest:VideoControl /> <!-- but this does? --> <!--<ModelVisual3D> <ModelVisual3D.Content> <GeometryModel3D> <GeometryModel3D.Geometry> <MeshGeometry3D Positions="-100,-100,0 100,-100,0 100,100,0 -100,100,0" TextureCoordinates="0,1 1,1 1,0 0,0" TriangleIndices="0 1 2 0 2 3" /> </GeometryModel3D.Geometry> <GeometryModel3D.Material> <DiffuseMaterial> <DiffuseMaterial.Brush> <VisualBrush> <VisualBrush.Visual> <MediaElement Source="http://www.quirksmode.org/html5/videos/big_buck_bunny.mp4" /> </VisualBrush.Visual> </VisualBrush> </DiffuseMaterial.Brush> </DiffuseMaterial> </GeometryModel3D.Material> </GeometryModel3D> </ModelVisual3D.Content> </ModelVisual3D>--> </Viewport3D> VideoControl.xaml <UIElement3D x:Class="MediaElementTest.VideoControl" xmlns="http://schemas.microsoft.com/winfx/2006/xaml/presentation" xmlns:x="http://schemas.microsoft.com/winfx/2006/xaml"/> VideoControl.xaml.cs public partial class VideoControl { public VideoControl() { InitializeComponent(); Visual3DModel = CreateModel(); } private GeometryModel3D CreateModel() { return new GeometryModel3D { Geometry = new MeshGeometry3D { Positions = new Point3DCollection { new Point3D(-100, -100, 0), new Point3D(100, -100, 0), new Point3D(100, 100, 0), new Point3D(-100, 100, 0) }, TextureCoordinates = new PointCollection { new Point(0, 1), new Point(1, 1), new Point(1, 0), new Point(0, 0) }, TriangleIndices = new Int32Collection { 0, 1, 2, 0, 2, 3 } }, Material = new DiffuseMaterial(new VisualBrush(new MediaElement { Source = new Uri("http://www.quirksmode.org/html5/videos/big_buck_bunny.mp4", UriKind.RelativeOrAbsolute) })) }; } }

    Read the article

< Previous Page | 242 243 244 245 246 247 248 249 250 251 252 253  | Next Page >