Search Results

Search found 24623 results on 985 pages for 'linux'.

Page 246/985 | < Previous Page | 242 243 244 245 246 247 248 249 250 251 252 253  | Next Page >

• Bridge virtual machines out WLAN interface

  - by Thomas

  It seems that my wlan card (intel 5100 AGN) firmware doesn't allow "spoofing" MAC addresses. This has the side effect of destroying the capability to bridge out my virtual machines on that interface. Apparently this is a common thing on wlan cards. I can see the incoming traffic just fine in my virtual machines, but their DHCP queries don't get bridged out of the WLAN card. It works perfectly well when using the wired ethernet port. Is there a workaround for this? MAC-NAT or something? I don't want to route my virtual machines out to the Internet because I don't want my host OS to even have an IP address. I'm using Linux and KVM for virtualization.

  Read the article

• Import emails from Claws IMAP cache

  - by calandoa

  I am trying to import an IMAP account composed of many folders from Claws Mail internal cache. Claws is unfortunately unable to export all the folders by selecting the root account. When checking the internal Claws cache folder, each mail is a plain text file named as following: base_path/My Account/Folder ABC/1 base_path/My Account/Folder ABC/2 base_path/My Account/Folder ABC/3 base_path/My Account/Folder ABC/4 base_path/My Account/Folder DEF/1 base_path/My Account/Folder DEF/2 base_path/My Account/Folder DEF/3 base_path/My Account/Folder X/etc... I tried to import this structure with different mails reader like KMail and Balsa, but each import failed. I just would like all these mails easily accessible and readable. Which tool on Linux can I use to import such a structure?

  Read the article

• internal compiler error

  - by hyperboreean

  I am getting this message: internal compiler error: Segmentation fault Please submit a full bug report, with preprocessed source if appropriate. See <file:///usr/share/doc/gcc-4.4/README.Bugs> for instructions. for every compilation that takes longer (ie: linux kernel, kde sources etc.) I've tried other OS (at that moment I was on Fedora 12, now on Debian; was a Suse also) and it didn't work. I've tried replacing my hard disk, since it needed an upgrade either ways - that didn't work either. I assumed that it's the RAM fault - tested them with memtest and it says they are fine. Does anyone know what else I can do in order to figure out where the problem is?

  Read the article

• bash starts replacing the characters on the current line insead of moving over to the next line

  - by Lazer

  I use bash shell $ bash --version GNU bash, version 3.2.25(1)-release (x86_64-redhat-linux-gnu) Copyright (C) 2005 Free Software Foundation, Inc. $ Sometimes, when typing a command on the prompt that is pretty lengthy and does not fit in the current line, instead of displaying the extra characters on the next line, bash starts again on the current line.. replacing the characters that were there and making a mess. what should happen : |---------------------------------------------| | $ my big long command takes a lot of argumen| | s and does not fit in a single line | | | |---------------------------------------------| what happens instead : |---------------------------------------------| | s and does not fit in a single linef argumen| | | | | |---------------------------------------------| The issue is intemittent If I resize my shell window to really small width, normal behaviour is restored Does anyone have any idea what is happening here? $ echo $TERM xterm $ echo $PS1 \[\e[30m\][\t]\[\e[0m\]\[\e]0;\w\a\]\[\e[30m\][\W]$ $

  Read the article

• Step by step USB Wi-Fi driver install for mint 15

  - by Andy

  I'm running Linux mint 15 32 bit on a Dell inspiron 2200. I have given up trying to get the Broadcom BCM4318 built in wireless working, so bought a Dynamode Nano 802.11n wireless USB adapter. It came with an install disc. I have no idea how to install it. Could someone please point me in the right direction for full, idiot proof, step by step instructions. I've been using Ubuntu 12.04 but am totally new to mint 15, so best to assume no previous knowledge. Thanks in advance.

  Read the article

• Clonezilla is not able to clone a RAID 1 disk

  - by Adrian

  I have a HP Server DL320 G5. There are two SATA hard disks configured as RAID 1 through HP embedded RAID controller. Server OS is running GNU/Linux (Fedora) Server booted up with clonezilla live CD. The image will be stored on a NAS connected through NFS. Clonezilla could mount the NFS share and could see the two hard disks /dev/sda and /dev/sdb. I selected /dev/sda for disk cloning. However I could not see the cloning progress and got straight into a prompt for reboot, poweroff, command line I tried to select /dev/sdb but the same issue.

  Read the article

• Redirect input from one terminal to another

  - by Niki Yoshiuchi

  I have sshed into a linux box and I'm using dvtm and bash (although I have also tried this with Gnu screen and bash). I have two terminals, current /dev/pts/29 and /dev/pts/130. I want to redirect the input from one to the other. From what I understand, in /dev/pts/130 I can type: cat </dev/pts/29 And then when I type in /dev/pts/29 the characters I type should show up in /dev/pts/130. However what ends up happening is that every other character I type gets redirected. For example, if I type "hello" I get this: /dev/pts/29 | /dev/pts/130 $ | $ cat </dev/pts/29 $ el | hlo This is really frustrating as I need to do this in order to redirect the io of a process running in gdb (I've tried both run /dev/pts/# and set inferior-tty /dev/pts/# and both resulted in the aforementioned behavior). Am I doing something wrong, or is this a bug in bash/screen/dvtm?

  Read the article

• Forward Windows Events Logs to Rsyslog

  - by SamCulley

  Thanks for taking time to read this post. Basically I would like to forward Windows Events Logs from all my desktop clients to a linux box with rsyslog on. Rsyslog provide a Windows agent to do just that but its 40 euros per license and when you have x amount of machines that cost adds up. I was wondering if there is a FOSS alternative available I have tried searching the Google but haven't managed to find anything. Hopefully someone might already faced this same problem and are using an alternative that they could recommend. Again thanks for reading, Kind Regards Sam

  Read the article

• performance block countries using iptables /netfilter

  - by markus

  It's easy to block IPs from country using iptables (e.g. like http://www.cyberciti.biz/faq/block-entier-country-using-iptables/). However I read that the performance can go down if the deny list get too large. An alternative is installing the iptables geoip patch or using ipset ( http://www.jsimmons.co.uk/2010/06/08/using-ipset-with-iptables-in-ubuntu-lts-1004-to-block-large-ip-ranges/) instead of iptables. Does anyone have experience with the various approaches and can say something about the performance differences ? Are there are other ways to block country IPs in linux which I did't mentioned above?

  Read the article

• Problem with kickstart

  - by user70523

  Hi, I created a kickstart file ks.cfg and then I have put that in the bootable disk*(Ubuntu 10.04)* and then added the following line to the isolinux.cfg linux ks=ks.cfg and have not removed any other lines from the isoconfig.cfg file and then while installing the installation is not automated,again it is asking for language and all. If i removed include menu.cfg or any other line from isolinux.cfg i am getting a boot error. What should i do now to automate the installation.Where should i add the boot parameters so that installation will start from the ks.cfg . Thanks and Regards Ravi Kumar

  Read the article

• Automatically wake up notebooks not on the ethernet

  - by gletscher

  I am looking for an automated backup system and I like bacula. I have 3 Notebooks and a Desktop computer that need regular backup. Now I don't want to let them run all night just to do the backuping, so I was thinking I could use wake-on-lan to have bacula wake up the machines, then do the backups, and shut them down afterswards. While this may work with devices on the ethernet, it won't work with the Notebooks on the wifi. So is it possible to have the Notebooks schedules to automatically wake up from suspend or shutdown ? Or is it possible to interject a shutdown command if it is after a certain hour and call the bacula director to start the backup now? I'm new to controlling the linux system using scripts, so any hints on how and where to start are greatly appreciated. Thanks alot for your help, input and ideas.

  Read the article

• What do you use to loadbalance IPv6 services?

  - by Michael Renner

  Hi, the current Linux software environment for IPv6 load balancing looks a bit grim. IPVS has rudimentary support for IPv6 but it's far from complete. NAT for IPv6 seems to be a no-go. Are there any other projects which aim for this goal? Does the IPv6 support in other OS look better? Are there any commercial products which have been successfully used in production environments with non-trivial load patterns? Or is it just that the time for IPv6 hasn't come... yet? ;) best regards, Michael

  Read the article

• clam anti-virus is slowing down my server performance

  - by Scarface

  Hey guys, I just installed clam av http://sourceforge.net/projects/php-clamav/ for scanning file uploads on my linux VPN running php. The problem is that for some reason just initiating the extension in the php ini file slows down my entire network. Regular requests such as changing pages that should take less than 1 second take 5. Has anyone ever experienced this before or have a good virus scanning alternative for scanning file uploads? extension=clamav.so [clamav] clamav.dbpath="/usr/share/clamav" clamav.keeptmp=20 clamav.maxreclevel=16 clamav.maxfiles=10000 clamav.maxfilesize=26214400 clamav.maxscansize=104857600 clamav.keeptmp=0

  Read the article

• How can I create persistent SSH connection to "stream" commands over a period of time?

  - by Darth

  Say that I have an application running on one PC that is sending commands via SSH to another PC on the network (both machines running Linux). For example every time something happens on #1, I want to run a task on #2. In this setup, I have to create SSH connection on every single command. Is there any simple way to do this with basic unix tools without programming custom client/server application? Basically all I want is to establish a connection over SSH and then send one command after another.

  Read the article

• What is the correct term for the number of bits used by an operating system

  - by benc

  Recently, some discussions came up about 32 bit vs. 64 bit implementations of operating systems. While I was composing a message about this topic, I realized that I did not know if there was a correct term for the number of bits supported by an operating system. For example, various versions of Solaris and Linux have 32bit and 64bit releases. Is the distinction "architecture"? In my experience, that has referred to chip types (Intel vs. PPC). Is it a "release"? Typically, I think of a release as a version number a consistent feature set, that might run on different architectures. Maybe it is just "architecture", after all, even though a chip family might have used several different bit sizes over time, the chips themselves are different when you jump from 32bit to 64bit.

  Read the article

• Unable to bring back terminal launcher in fedora

  - by Sandeepan Nath

  Our office housing keeping guy sat on my linux (Fedora 7) system and somehow removed the main panel. By panel I mean where all the menus are there - Applications, Places, System etc. and contains a tab for every running application. I brought back the panel but now I don't see the terminal launcher and I can't find it anywhere. It used to be there in "Applications - System Tools - Terminal" but now the System Tools option itself is not present there. System - Preferences - Look and Feel - Main Menu. There one System option is unchecked but I can't check it and apply. I am logged in as root. How do I bring it back? Please help. This is very irritating and weird. That guy doesn't even know what he has done so no use of asking him. :)

  Read the article

• Using the right folder for the right job. Article link, please?

  - by Droogans

  There are specific folders designed for specific tasks. /var/www holds your web sites, /usr/bin contains files to run your applications...yet I still find myself putting nearly all of my work in ~. Is it possible to overuse my home directory? Will it come back to haunt me? Anyone have a good link to an article of best practices for organizing your files so that they are placed in their "correct" place? Is there even such a thing in Linux? I am referring specifically to user-generated content. I do not compile applications from source, I use apt-get for those tasks. This article has a great introduction to what I'm looking for. Table 3-2, "Subdirectories of the root directory" is the sort of thing I'm looking for, but with more details/examples.

  Read the article

• Changing startup parameters for MySQL

  - by RN

  I need to remove skip-networking from MySQL startup parameters I am running MySQL on Linux on Centos on a VPS Can someone please tell a newbie how to do this ? I suppose to start and stop the mySQL server, I have to do something like this /etc/init.d/mysqld stop /etc/init.d/mysqld start ps -ef|grep 'mysql' root 11331 20220 0 10:53 pts/0 00:00:00 grep mysql root 32452 1 0 Apr02 ? 00:00:00 /bin/sh /usr/bin/mysqld_safe --skip-grant-tables --skip-networking mysql 32504 32452 0 Apr02 ? 00:00:18 /usr/libexec/mysqld --basedir=/usr --datadir=/var/lib/mysql --user=mysql --pid-file=/var/run/mysqld/mysqld.pid --skip-external-locking --socket=/var/lib/mysql/mysql.sock --skip-grant-tables --skip-networking

  Read the article

• Re-assembling the RAID-5 array reboots my CentOS-5 machine

  - by xraminx

  I have 3 HDD's, each divided into 3 partitions. I had created a RAID-1 for boot partition md0 created from sda0, sdb0 and had also created two RAID-5 arrays: md1 created from sda1, sdb1, sdc1 md2 created from sda2, sdb2, sdc2 It used to work fine but one day I had to power off the machine (cold reboot) to get any response from the machine. After that, when the system started booting, it tried for a while to reconstruct the RAID arrays but after a few minutes it crashed silently. I booted the system in linux rescue mode from the DVD and tried to re-assemble the RAID devices manually. I was able to re-assemble md0 and md1 using: mdadm --assemble --scan /dev/md0 mdadm --assemble --scan /dev/md1 But when I try to re-assemble md2 using: mdadm --assemble --scan /dev/md2 the system reboots silently again. How can I fix this problem?

  Read the article

• nagios-nrpe-unable-to-read-output [closed]

  - by Bill S

  Oracle Linux; Icinga; Nagios plugins I did all the easy steps command runs fine standalone through my normal login; looked at /var/log/messages to see if any clues there Trying to run plugin under nrpe login - cant login don't know password; does this password matter? can I reset it? clone id? Any way to have shell being executed log all commands and output to somewhere? Trying to run this shell script plugin "nqcmd OBIEE plugin for Nagios" from this URL: http://www.rittmanmead.com/2012/09/advanced-monitoring-of-obiee-with-nagios/ I went through script and made sure that everything obvious was set to 755 Any help would be appreciated

  Read the article

• BIOS password and hardware clock problems

  - by Slartibartfast

  I have HP 6730b lap top. I've bought it used and installed (Gentoo) linux on it. BIOS is protected with password, and guy I bought it from said "I've tweaked BIOS from Windows program, it never asked me for password". I've tried to erase password by removing battery, but it's still there. What did get erased obviously is hw clock. This is what hapends: a) I can leave lap top in January 1980 and it works b) I can correct system time, but boot wil fail with "superblock mount time in future" from where I need to manually do fsck and continue boot c) I can correct system time and sync it with hwclock -w but than it will behave as b) and it will reset BIOS time to 1.1.1980 00:00 So I need either a way to bypass a BIOS password (wich after lot of googling seems impossible),a way to persist a clock, or a setup that will enable hw clock in eighties, system clock in present time and normal boot.

  Read the article

• Compiling to a binary from source

  - by Chords

  I'm using WKHTMLTOPDF on a 64-bit Linux server and I'm running into problems with the version. Seen here: http://code.google.com/p/wkhtmltopdf/downloads/list There's slim pickins when it comes to pre-compiled binaries. I started with version 0.9.9 which has a few bugs. I upgraded to 0.11.0 RC 1 to find a slew of new problems, namely the following: http://code.google.com/p/wkhtmltopdf/issues/detail?id=730 I think 0.10 RC 2 would work, and the thread above suggests compiling from the source has a fix for the error I'm getting, but I don't know how to do that. Can anyone explain how I can create a static binary myself, or would anyone be willing to create and post one for the countless people waiting for this fix?

  Read the article

• What is the EGG environment variable?

  - by Randall

  A user on our (openSuSE) linux systems attempted to run sudo, and triggered an alert. He has the environment variable EGG set - EGG=UH211åH1ÒH»ÿ/bin/shHÁSH211çH1ÀPWH211æ°;^O^Ej^A_j<X^O^EÉÃÿ This looks unusual to say the least. Is EGG a legitimate environment variable? (I've found some references to PYTHON_EGG_CACHE - could be related? But that environment variable isn't set for this user). If it's legit, then I imagine this group has the best chance of recognizing it. Or, given the embedded /bin/sh in the string above, does anyone recognize this as an exploit fingerprint? It wouldn't be the first time we had a cracked account (sigh).

  Read the article

• Webserver security, intrusion detection, and file intregrity

  - by enfield

  I would like to add some type of tracking / alerting on some linux webservers running PHP and Apache. In doing searches I have come across a lot of info from 2006-2009. Would like to revisit things and see what others are doing now. The main purpose here is to track when any files are changed and if so alert me somehow. The same goes for IDS and hopefully something that can reside on same server? Since some of these are small scale projects I would prefer opensource/free solutions that are really effective. Although I would still like to hear of other alternatives if someone has the experience and the cost can be justified.

  Read the article

• setting nproc in /etc/security/limit.conf prevents ssh login

  - by omry

  I am trying to use /etc/security/limit.conf on Linux (Debian) to limit the number of processes per user. for starters, I tried to limit my own user processes by adding this to /etc/security/limit.conf: omry hard nproc 100 this locked my user out of ssh. I could open new processes (verified with su omry), but could not log into ssh with that user : sshd reported this in it's log: fatal: setreuid 1000: Resource temporarily unavailable also, I am certain my user is not running anything near 100 processes (actually 6). what can be the reason for this?

  Read the article

< Previous Page | 242 243 244 245 246 247 248 249 250 251 252 253  | Next Page >