Search Results

Search found 30486 results on 1220 pages for 'network level auth'.

Page 246/1220 | < Previous Page | 242 243 244 245 246 247 248 249 250 251 252 253  | Next Page >

• Allowing connections initiated from outside

  - by Mark S. Rasmussen

  I've got an old Juniper SSG5 running ScreenOS 5.4.0r6.0. Once a day, more or less, it'll start randomly dropping packets at a rate of ~5-10%. We currently solve this issue by simply rebooting the unit, after which it resumes working in perfect condition. As this error has started appearing randomly, without any configuration or hardware changes, I'm assuming I've got an aging unit about to fail. As such, I've got a replacement SSG5 running ScreenOS 6.0. I've dumped the config on the 5.4 and imported it into a clean 6.0, and it seems to gladly accept it, and all my configuration seems to be A-OK. However, upon connecting the new unit, all outside-initiated connections seem to be blocked. If I browse our external IP from the inside, everything works perfectly, and it's not just port 80, SSH, Crashplan - all of our policies route correctly. All normal networking, initiated from the inside, work perfectly as well. If on the other hand I browse our external IP from the outside, everything is blocked. Barring differences between ScreenOS 5.4 and 6.0, the config is identical. Is there a setting somewhere that defines whether outside/inside initiated connections are allowed? unset key protection enable set clock timezone 1 set vrouter trust-vr sharable set vrouter "untrust-vr" exit set vrouter "trust-vr" unset auto-route-export exit set service "MyVOIP_UDP4569" protocol udp src-port 0-65535 dst-port 4569-4569 set service "MyVOIP_TCP22" protocol tcp src-port 0-65535 dst-port 22-22 set service "MyRDP" protocol tcp src-port 0-65535 dst-port 3389-3389 set service "MyRsync" protocol tcp src-port 0-65535 dst-port 873-873 set service "NZ_FTP" protocol tcp src-port 0-65535 dst-port 40000-41000 set service "NZ_FTP" + tcp src-port 0-65535 dst-port 21-21 set service "PPTP-VPN" protocol 47 src-port 2048-2048 dst-port 2048-2048 set service "PPTP-VPN" + tcp src-port 1024-65535 dst-port 1723-1723 set service "NZ_FMS_1935" protocol tcp src-port 0-65535 dst-port 1935-1935 set service "NZ_FMS_1935" + udp src-port 0-65535 dst-port 1935-1935 set service "NZ_FMS_8080" protocol tcp src-port 0-65535 dst-port 8080-8080 set service "CrashPlan Server" protocol tcp src-port 0-65535 dst-port 4280-4280 set service "CrashPlan Console" protocol tcp src-port 0-65535 dst-port 4282-4282 unset alg sip enable set alg appleichat enable unset alg appleichat re-assembly enable set alg sctp enable set auth-server "Local" id 0 set auth-server "Local" server-name "Local" set auth default auth server "Local" set auth radius accounting port 1646 set admin name "netscreen" set admin password "XXX" set admin auth web timeout 10 set admin auth dial-in timeout 3 set admin auth server "Local" set admin format dos set vip multi-port set zone "Trust" vrouter "trust-vr" set zone "Untrust" vrouter "trust-vr" set zone "DMZ" vrouter "trust-vr" set zone "VLAN" vrouter "trust-vr" set zone "Untrust-Tun" vrouter "trust-vr" set zone "Trust" tcp-rst set zone "Untrust" block unset zone "Untrust" tcp-rst set zone "MGT" block unset zone "V1-Trust" tcp-rst unset zone "V1-Untrust" tcp-rst set zone "DMZ" tcp-rst unset zone "V1-DMZ" tcp-rst unset zone "VLAN" tcp-rst set zone "Untrust" screen tear-drop set zone "Untrust" screen syn-flood set zone "Untrust" screen ping-death set zone "Untrust" screen ip-filter-src set zone "Untrust" screen land set zone "V1-Untrust" screen tear-drop set zone "V1-Untrust" screen syn-flood set zone "V1-Untrust" screen ping-death set zone "V1-Untrust" screen ip-filter-src set zone "V1-Untrust" screen land set interface ethernet0/0 phy full 100mb set interface ethernet0/3 phy full 100mb set interface ethernet0/4 phy full 100mb set interface ethernet0/5 phy full 100mb set interface ethernet0/6 phy full 100mb set interface "ethernet0/0" zone "Untrust" set interface "ethernet0/1" zone "Null" set interface "bgroup0" zone "Trust" set interface "bgroup1" zone "Trust" set interface "bgroup2" zone "Trust" set interface bgroup2 port ethernet0/2 set interface bgroup0 port ethernet0/3 set interface bgroup0 port ethernet0/4 set interface bgroup1 port ethernet0/5 set interface bgroup1 port ethernet0/6 unset interface vlan1 ip set interface ethernet0/0 ip 215.173.182.18/29 set interface ethernet0/0 route set interface bgroup0 ip 192.168.1.1/24 set interface bgroup0 nat set interface bgroup1 ip 192.168.2.1/24 set interface bgroup1 nat set interface bgroup2 ip 192.168.3.1/24 set interface bgroup2 nat set interface ethernet0/0 gateway 215.173.182.17 unset interface vlan1 bypass-others-ipsec unset interface vlan1 bypass-non-ip set interface ethernet0/0 ip manageable set interface bgroup0 ip manageable set interface bgroup1 ip manageable set interface bgroup2 ip manageable set interface bgroup0 manage mtrace unset interface bgroup1 manage ssh unset interface bgroup1 manage telnet unset interface bgroup1 manage snmp unset interface bgroup1 manage ssl unset interface bgroup1 manage web unset interface bgroup2 manage ssh unset interface bgroup2 manage telnet unset interface bgroup2 manage snmp unset interface bgroup2 manage ssl unset interface bgroup2 manage web set interface ethernet0/0 vip 215.173.182.19 2048 "PPTP-VPN" 192.168.1.131 set interface ethernet0/0 vip 215.173.182.19 + 4280 "CrashPlan Server" 192.168.1.131 set interface ethernet0/0 vip 215.173.182.19 + 4282 "CrashPlan Console" 192.168.1.131 set interface ethernet0/0 vip 215.173.182.22 22 "MyVOIP_TCP22" 192.168.2.127 set interface ethernet0/0 vip 215.173.182.22 + 4569 "MyVOIP_UDP4569" 192.168.2.127 set interface ethernet0/0 vip 215.173.182.22 + 3389 "MyRDP" 192.168.2.202 set interface ethernet0/0 vip 215.173.182.22 + 873 "MyRsync" 192.168.2.201 set interface ethernet0/0 vip 215.173.182.22 + 80 "HTTP" 192.168.2.202 set interface ethernet0/0 vip 215.173.182.22 + 2048 "PPTP-VPN" 192.168.2.201 set interface ethernet0/0 vip 215.173.182.22 + 8080 "NZ_FMS_8080" 192.168.2.216 set interface ethernet0/0 vip 215.173.182.22 + 1935 "NZ_FMS_1935" 192.168.2.216 set interface bgroup0 dhcp server service set interface bgroup1 dhcp server service set interface bgroup2 dhcp server service set interface bgroup0 dhcp server auto set interface bgroup1 dhcp server auto set interface bgroup2 dhcp server auto set interface bgroup0 dhcp server option domainname companyalan set interface bgroup0 dhcp server option dns1 192.168.1.131 set interface bgroup1 dhcp server option domainname companyblan set interface bgroup1 dhcp server option dns1 192.168.2.202 set interface bgroup2 dhcp server option dns1 8.8.8.8 set interface bgroup2 dhcp server option wins1 8.8.4.4 set interface bgroup0 dhcp server ip 192.168.1.2 to 192.168.1.116 set interface bgroup1 dhcp server ip 192.168.2.2 to 192.168.2.116 set interface bgroup2 dhcp server ip 192.168.3.2 to 192.168.3.126 unset interface bgroup0 dhcp server config next-server-ip unset interface bgroup1 dhcp server config next-server-ip unset interface bgroup2 dhcp server config next-server-ip set interface "ethernet0/0" mip 215.173.182.21 host 192.168.2.202 netmask 255.255.255.255 vr "trust-vr" set interface "serial0/0" modem settings "USR" init "AT&F" set interface "serial0/0" modem settings "USR" active set interface "serial0/0" modem speed 115200 set interface "serial0/0" modem retry 3 set interface "serial0/0" modem interval 10 set interface "serial0/0" modem idle-time 10 set flow tcp-mss unset flow tcp-syn-check unset flow tcp-syn-bit-check set flow reverse-route clear-text prefer set flow reverse-route tunnel always set pki authority default scep mode "auto" set pki x509 default cert-path partial set pki x509 dn name "[email protected]" set dns host dns1 0.0.0.0 set dns host dns2 0.0.0.0 set dns host dns3 0.0.0.0 set address "Trust" "192.168.1.0/24" 192.168.1.0 255.255.255.0 set address "Trust" "192.168.2.0/24" 192.168.2.0 255.255.255.0 set address "Trust" "192.168.3.0/24" 192.168.3.0 255.255.255.0 set crypto-policy exit set ike respond-bad-spi 1 set ike ikev2 ike-sa-soft-lifetime 60 unset ike ikeid-enumeration unset ike dos-protection unset ipsec access-session enable set ipsec access-session maximum 5000 set ipsec access-session upper-threshold 0 set ipsec access-session lower-threshold 0 set ipsec access-session dead-p2-sa-timeout 0 unset ipsec access-session log-error unset ipsec access-session info-exch-connected unset ipsec access-session use-error-log set vrouter "untrust-vr" exit set vrouter "trust-vr" exit set l2tp default ppp-auth chap set url protocol websense exit set policy id 1 from "Trust" to "Untrust" "Any" "Any" "ANY" permit set policy id 1 exit set policy id 2 from "Untrust" to "Trust" "Any" "VIP(215.173.182.19)" "PPTP-VPN" permit traffic set policy id 2 exit set policy id 3 from "Untrust" to "Trust" "Any" "VIP(215.173.182.22)" "HTTP" permit log set policy id 3 set service "MyRDP" set service "MyRsync" set service "MyVOIP_TCP22" set service "MyVOIP_UDP4569" exit set policy id 6 from "Trust" to "Trust" "192.168.1.0/24" "192.168.2.0/24" "ANY" deny set policy id 6 exit set policy id 7 from "Trust" to "Trust" "192.168.2.0/24" "192.168.1.0/24" "ANY" deny set policy id 7 exit set policy id 8 from "Trust" to "Trust" "192.168.3.0/24" "192.168.1.0/24" "ANY" deny set policy id 8 exit set policy id 9 from "Trust" to "Trust" "192.168.3.0/24" "192.168.2.0/24" "ANY" deny set policy id 9 exit set policy id 10 from "Untrust" to "Trust" "Any" "MIP(215.173.182.21)" "NZ_FTP" permit set policy id 10 exit set policy id 11 from "Untrust" to "Trust" "Any" "VIP(215.173.182.22)" "PPTP-VPN" permit set policy id 11 exit set policy id 12 from "Untrust" to "Trust" "Any" "VIP(215.173.182.22)" "NZ_FMS_1935" permit set policy id 12 set service "NZ_FMS_8080" exit set policy id 13 from "Untrust" to "Trust" "Any" "VIP(215.173.182.19)" "CrashPlan Console" permit set policy id 13 set service "CrashPlan Server" exit set nsmgmt bulkcli reboot-timeout 60 set ssh version v2 set config lock timeout 5 unset license-key auto-update set telnet client enable set snmp port listen 161 set snmp port trap 162 set vrouter "untrust-vr" exit set vrouter "trust-vr" unset add-default-route exit set vrouter "untrust-vr" exit set vrouter "trust-vr" exit Note that I've previously posted a similar question (pertaining to the same device & replacement, but ultimately caused by a malfunctioning switch, and thus clouding the current issue): Outbound traffic being blocked for MIP/VIPped servers (Juniper SSG5)

  Read the article

• Is it possible to detect nearby Wi-Fi enabled devices, not necessarily on the same network? [closed]

  - by Sky

  first question on StackExchange ever. I hope I got the right board. I'm trying to create a device (either from a standard AP or some other unconventional means) that will be able to detect nearby Wi-Fi enabled devices. For example, if a cellular phone (iPhone for instance) would be carried into the secured area, its MAC address will be logged. A cellular phone is a good example because it's the most common threat that should be detected. Some important points: The detection can be either active or passive, doesn't matter. The detected device might be connected to a different network, or might not be connected to anything at all. I assume most cellular phones are actively probing when not connected, but I'm not sure. It is important to not only identify the breach, but also to identify the device (MAC address). Conventional hardware is only optional. Distance of detection is at least 6 meters (20 feet). Handling one device at a time is good. Speed of detection is important, under 5 seconds is ideal. So my question is, is this even possible? If so, what can I use in order to make this a reality? Thank you for reading!

  Read the article

• NetApp erroring with: STATUS_NOLOGON_WORKSTATION_TRUST_ACCOUNT

  - by Sobrique

  Since a sitewide upgrade to Windows 7 on desktop, I've started having a problem with virus checking. Specifically - when doing a rename operation on a (filer hosted) CIFS share. The virus checker seems to be triggering a set of messages on the filer: [filerB: auth.trace.authenticateUser.loginTraceIP:info]: AUTH: Login attempt by user server-wk8-r2$ of domain MYDOMAIN from client machine 10.1.1.20 (server-wk8-r2). [filerB: auth.dc.trace.DCConnection.statusMsg:info]: AUTH: TraceDC- attempting authentication with domain controller \\MYDC. [filerB: auth.trace.authenticateUser.loginRejected:info]: AUTH: Login attempt by user rejected by the domain controller with error 0xc0000199: STATUS_NOLOGON_WORKSTATION_TRUST_ACCOUNT. [filerB: auth.trace.authenticateUser.loginTraceMsg:info]: AUTH: Delaying the response by 5 seconds due to continuous failed login attempts by user server-wk8-r2$ of domain MYDOMAIN from client machine 10.1.1.20. This seems to specifically trigger on a rename so what we think is going on is the virus checker is seeing a 'new' file, and trying to do an on-access scan. The virus checker - previously running as LocalSystem and thus sending null as it's authentication request is now looking rather like a DOS attack, and causing the filer to temporarily black list. This 5s lock out each 'access attempt' is a minor nuisance most of the time, and really quite significant for some operations - e.g. large file transfers, where every file takes 5s Having done some digging, this seems to be related to NLTM authentication: Symptoms Error message: System error 1808 has occurred. The account used is a computer account. Use your global user account or local user account to access this server. A packet trace of the failure will show the error as: STATUS_NOLOGON_WORKSTATION_TRUST_ACCOUNT (0xC0000199) Cause Microsoft has changed the functionality of how a Local System account identifies itself during NTLM authentication. This only impacts NTLM authentication. It does not impact Kerberos Authentication. Solution On the host, please set the following group policy entry and reboot the host. Network Security: Allow Local System to use computer identity for NTLM: Disabled Defining this group policy makes Windows Server 2008 R2 and Windows 7 function like Windows Server 2008 SP1. So we've now got a couple of workaround which aren't particularly nice - one is to change this security option. One is to disable virus checking, or otherwise exempt part of the infrastructure. And here's where I come to my request for assistance from ServerFault - what is the best way forwards? I lack Windows experience to be sure of what I'm seeing. I'm not entirely sure why NTLM is part of this picture in the first place - I thought we were using Kerberos authentication. I'm not sure how to start diagnosing or troubleshooting this. (We are going cross domain - workstation machine accounts are in a separate AD and DNS domain to my filer. Normal user authentication works fine however.) And failing that, can anyone suggest other lines of enquiry? I'd like to avoid a site wide security option change, or if I do go that way I'll need to be able to supply detailed reasoning. Likewise - disabling virus checking works as a short term workaround, and applying exclusions may help... but I'd rather not, and don't think that solves the underlying problem. EDIT: Filers in AD ldap have SPNs for: nfs/host.fully.qualified.domain nfs/host HOST/host.fully.qualified.domain HOST/host (Sorry, have to obfuscate those). Could it be that without a 'cifs/host.fully.qualified.domain' it's not going to work? (or some other SPN? ) Edit: As part of the searching I've been doing I've found: http://itwanderer.wordpress.com/2011/04/14/tread-lightly-kerberos-encryption-types/ Which suggests that several encryption types were disabled by default in Win7/2008R2. This might be pertinent, as we've definitely had a similar problem with Keberized NFSv4. There is a hidden option which may help some future Keberos users: options nfs.rpcsec.trace on (This hasn't given me anything yet though, so may just be NFS specific). Edit: Further digging has me tracking it back to cross domain authentication. It looks like my Windows 7 workstation (in one domain) is not getting Kerberos tickets for the other domain, in which my NetApp filer is CIFS joined. I've done this separately against a standalone server (Win2003 and Win2008) and didn't get Kerberos tickets for those either. Which means I think Kerberos might be broken, but I've no idea how to troubleshoot further. Edit: A further update: It looks like this may be down Kerberos tickets not being issued cross domain. This then triggers NTLM fallback, which then runs into this problem (since Windows 7). First port of call will be to investigate the Kerberos side of things, but in neither case do we have anything pointing at the Filer being the root cause. As such - as the storage engineer - it's out of my hands. However, if anyone can point me in the direction of troubleshooting Kerberos spanning two Windows AD domains (Kerberos Realms) then that would be appreciated. Options we're going to be considering for resolution: Amend policy option on all workstations via GPO (as above). Talking to AV vendor about the rename triggering scanning. Talking to AV vendor regarding running AV as service account. investigating Kerberos authentication (why it's not working, whether it should be).

  Read the article

• Connecting XRAID to Sunfire via LSI FC card - Drives not showing up

  - by Matthew Watson

  Hi, I've got a Sunfire T1000 machine ( Solaris 10 10/09 s10s_u8wos_08a SPARC ) with a LSI7404EP-LC fibre channel card in it. This is plugged into an XRAID. The system seems to have picked up the card > /usr/platform/`uname -i `/sbin/prtdiag IO Location Type Slot Path Name Model ----------- ----- ---- --------------------------------------------- ------------------------- --------- MB/PCIE0 PCIE 0 /pci@780/fibre-channel fibre-channel MB/PCIE0 PCIE 0 /pci@780/fibre-channel fibre-channel MB/NET0 PCIE MB /pci@7c0/pci@0/network@4 network-pci14e4,1668 MB/NET1 PCIE MB /pci@7c0/pci@0/network@4,1 network-pci14e4,1668 MB/NET2 PCIX MB /pci@7c0/pci@0/pci@8/network@1 network-pci108e,1648 MB/NET3 PCIX MB /pci@7c0/pci@0/pci@8/network@1,1 network-pci108e,1648 MB/PCIX PCIX MB /pci@7c0/pci@0/pci@8/scsi@2 scsi-pci1000,50 LSI,1064 However it doesn't seem to be able to see the xraid attached to it, lsiutil only reports the onboard SAS controller. > /usr/local/bin/lsiutil ~ LSI Logic MPT Configuration Utility, Version 1.62, January 14, 2009 1 MPT Port found Port Name Chip Vendor/Type/Rev MPT Rev Firmware Rev IOC 1. mpt0 LSI Logic SAS1064 A3 105 010a0000 0 Select a device: [1-1 or 0 to quit] I've tried adding the configuration to /kernal/drv/sd.conf and /kernal/drv/ssd.conf as per this thread, however format still cannot see any drives on the xraid. I'm not sure where to go next. Any suggestions? From what I've read..this should pretty much just eb plug it in and they show up in format..

  Read the article

• How to get gigabit network speeds on Windows XP?

  - by JB

  We've just installed gigabit switches at work, and things on the Linux side are going well. Our linux boxes, which use a Intel Corporation 82566DM-2 Gigabit nic (according to lspci), consistently get over 900 mbits/sec: iperf -c ipserver ------------------------------------------------------------ Client connecting to ipserver, TCP port 5001 TCP window size: 16.0 KByte (default) ------------------------------------------------------------ [ 3] local 192.168.40.9 port 39823 connected with 192.168.1.115 port 5001 [ ID] Interval Transfer Bandwidth [ 3] 0.0-10.0 sec 1.08 GBytes 929 Mbits/sec We have a bunch of Windows XP 64-bit machines that use Broadcom NetXtreme 57xx cards. I spent around a day trying to get equivalent speeds on them, but couldn't get above 200 Mbits/sec. I noticed the Windows iperf tests said that the TCP window size was 8 Kb by default (as opposed to 16 Kb on Linux, so I modified my test to reflect that. Still no love. I went to Broadcom's site, downloaded the latest drivers for the card and installed. Still no love. However, finally, I tried a 64 Kb window size with the new drivers, and finally an improvement! $ iperf -c ipserver -w64k ------------------------------------------------------------ Client connecting to ipserver, TCP port 5001 TCP window size: 64.0 KByte ------------------------------------------------------------ [ 3] local 192.168.40.214 port 1848 connected with 192.168.1.115 port 5001 [ ID] Interval Transfer Bandwidth [ 3] 0.0-10.0 sec 933 MBytes 782 Mbits/sec Much better, but still not really taking advantage of the full capabilities of the network. If the Linux box can reach 950 Mbits/sec consistently, this box should be able to as well. Also, if you're wondering about the medium, this is over the same cable...I'm switching back and forth. Any suggestion or ideas would be really welcome. Thanks!

  Read the article

• Do all routers really must know all routes to every router?

  - by Philipili

  This is my complicated and long question. First let's talk about the context. Network topology: PC A --- RT A --- RT C --- RT B --- PC B (RT C has a WAN NIC connected to "the cloud") With this situation : PC A must send a packet to PC B Default routes direct packets to the cloud We haven't access to RT C's configuration RT C only knows how to join network A, not network B RT A knows about network B RT B knows about network A RT C's routing table: Destination NIC Gateway 0.0.0.0 WAN Cloud Network A LAN A RT A's WAN RT A's routing table: Destination NIC Gateway 0.0.0.0 WAN LAN A Network B WAN LAN A RT B's routing table: Destination NIC Gateway 0.0.0.0 WAN LAN B Network A WAN LAN B I would like to permit PC A and PC B to communicate, but I don't have access to RT C. Networks B and BC are new. Can PC A send a packet to RT B's WAN NIC (which is possible) and "ask RT B to direct the packet to PC B" ? I believe replacing RT B with a VPN server should do the trick, but I would like to know if it is possible to make it without establishing a new connection.

  Read the article

• Is it possible to stop the "Beep" device on all computers in a Windows network?

  - by sharptooth

  On Windows the default behavior it to make an annoying "beep" sound every time Windows things something notable happened. The result is that when someone send a company-wide email via the MS Exchange all computers around my cubicle beep one by one. This is annoying and makes no sense. Luckily beeping can be shut off. Someone has to: open the "Device Manager", select "View - Show hidden devices", find the "Beep" device in "Non-Pug and Play Devices" node, open its properties, go to the "Driver" tab, set "startup type" to "Disabled" and click "Stop". The "Beep" device will stop and no longer produce the useless sound. This solution however requires tracking every computer and then talking to its user which is not very convenient. Device Manager doesn't allow stopping a device on another computer. I'm looking for a solution that can be deployed by the administrators team. We have a domain and the administrators even install the programs company-wide automatically. Are there any means to stop the "Beep" device an all computers in the Windows network with some remote-administration features automatically?

  Read the article

• OpenBSD logins via SSH seem to be ignoring my configured radius server

  - by Steve Kemp

  I've installed and configured a radius server upon my localhost - it is delegating auth to a remote LDAP server. Initially things look good: I can test via the console: # export user=skemp # export pass=xxx # radtest $user $pass localhost 1812 $secret Sending Access-Request of id 185 to 127.0.0.1 port 1812 User-Name = "skemp" User-Password = "xxx" NAS-IP-Address = 192.168.1.168 NAS-Port = 1812 rad_recv: Access-Accept packet from host 127.0.0.1 port 1812, id=185, Similarly I can use the login tool to do the same thing: bash-4.0# /usr/libexec/auth/login_radius -d -s login $user radius Password: $pass authorize However remote logins via SSH are failing, and so are invokations of "login" started by root. Looking at /var/log/radiusd.log I see no actual log of success/failure which I do see when using either of the previous tools. Instead sshd is just logging: sshd[23938]: Failed publickey for skemp from 192.168.1.9 sshd[23938]: Failed keyboard-interactive for skemp from 192.168.1.9 port 36259 ssh2 sshd[23938]: Failed password for skemp from 192.168.1.9 port 36259 ssh2 In /etc/login.conf I have this: # Default allowed authentication styles auth-defaults:auth=radius: ... radius:\ :auth=radius:\ :radius-server=localhost:\ :radius-port=1812:\ :radius-timeout=1:\ :radius-retries=5:

  Read the article

• HTTP 401 Challenge and HTTP 302 Login/Redirect won't work together in IIS7

  - by RandomBen

  I am developing a website using .NET 3.5 that allow users to visit the site and create logins using the standard Microsoft login controls. However, users do not need to login to do general things like view products. Now I need to setup the site so some of our Traveling Sales people are able to access it but not allow anyone else to access it. The easiest way I know how to do this is to turn on Windows Authentication for the Site in IIS7. When I do that I get all sorts of errors due to also having Forms Authentication turned on. If I turn Forms Auth then I get a different kind of error. Does anyone know how to make Forms Auth and Windows Auth play nice on a single site in IIS7 or some other way to create a required login without having me kill Forms Auth?

  Read the article

• How to merge .rpmnew files in Pluggable Authentication Modules (PAM)?

  - by Question Overflow

  A few .rpmnew files are being created after performing an upgrade of the Fedora OS. The normal procedure for merging .rpmnew files into the original ones is to compare the differences, make the necessary changes to the configuration on the .rpmnew files, and replace the original files with the new ones. However, the files contained in /etc/pam.d are links to files with same the filename appended with -ac, example: password-auth links to password-auth-ac and has password-auth.rpmnew as upgrade. How do I go about merging these files?

  Read the article

• Ping server NETBIOS name returns wrong IP and "Destination host unreachable"

  - by music2myear

  Problem server is Windows 2008 R2 VM running on VMWare ESXi 4 host. Single network adapter manually assigned single IP address (192.168.1.11). When I ping the server from any other network computer, it returns 192.168.1.124 and "Destination host unreachable". Yesterday I found a second network adapter assigned to this server with an IP of 169.254... indicating it had no real valid IP. Using the MAC addresses I determined which adapter was not needed/not wanted, and removed it using VMWare systems. This is the network Printer Server and, understandably, nothing is printing right now. I've looked at the solutions here Why was my ping answered by a different IP address than the one pinged? and they aren't applicable to my situation for the following reasons: Output of arp -a on another computer returns the correct IP address (.1.11) assigned to the correct MAC address, the incorrect IP .1.124 is not listed, and the MAC of the network adapter I removed yesterday is not listed at all. I checked out the Microsoft KB article which listed pretty much my exact symptoms ( http://support.microsoft.com/kb/981953 ) and it says to check binding orders and look for hidden adapters. But there are no hidden adapters, and there is only one Network Adapter listed in the Binding Order list. Essentially, I can communicate from the server TO any other network device, but I cannot communicate from any other network device TO the server. Help! UPDATE: Solution found, see this solution for the details.

  Read the article

• hosts.deny not blocking ip addresses

  - by Jamie

  I have the following in my /etc/hosts.deny file # # hosts.deny This file describes the names of the hosts which are # *not* allowed to use the local INET services, as decided # by the '/usr/sbin/tcpd' server. # # The portmap line is redundant, but it is left to remind you that # the new secure portmap uses hosts.deny and hosts.allow. In particular # you should know that NFS uses portmap! ALL:ALL and this in /etc/hosts.allow # # hosts.allow This file describes the names of the hosts which are # allowed to use the local INET services, as decided # by the '/usr/sbin/tcpd' server. # ALL:xx.xx.xx.xx , xx.xx.xxx.xx , xx.xx.xxx.xxx , xx.x.xxx.xxx , xx.xxx.xxx.xxx but i am still getting lots of these emails: Time: Thu Feb 10 13:39:55 2011 +0000 IP: 202.119.208.220 (CN/China/-) Failures: 5 (sshd) Interval: 300 seconds Blocked: Permanent Block Log entries: Feb 10 13:39:52 ds-103 sshd[12566]: pam_unix(sshd:auth): authentication failure; logname= uid=0 euid=0 tty=ssh ruser= rhost=202.119.208.220 user=root Feb 10 13:39:52 ds-103 sshd[12567]: pam_unix(sshd:auth): authentication failure; logname= uid=0 euid=0 tty=ssh ruser= rhost=202.119.208.220 user=root Feb 10 13:39:52 ds-103 sshd[12568]: pam_unix(sshd:auth): authentication failure; logname= uid=0 euid=0 tty=ssh ruser= rhost=202.119.208.220 user=root Feb 10 13:39:52 ds-103 sshd[12571]: pam_unix(sshd:auth): authentication failure; logname= uid=0 euid=0 tty=ssh ruser= rhost=202.119.208.220 user=root Feb 10 13:39:53 ds-103 sshd[12575]: pam_unix(sshd:auth): authentication failure; logname= uid=0 euid=0 tty=ssh ruser= rhost=202.119.208.220 user=root whats worse is csf is trying to auto block these ip's when the attempt to get in but although it does put ip's in the csf.deny file they do not get blocked either So i am trying to block all ip's with /etc/hosts.deny and allow only the ip's i use with /etc/hosts.allow but so far it doesn't seem to work. right now i'm having to manually block each one with iptables, I would rather it automatically block the hackers in case I was away from a pc or asleep

  Read the article

• Windows 2008 R2 Servers Sending Arp Requests for IPs outside Subnet

  - by Kyle Brandt

  By running a packet capture on my my routers I see some of my servers sending ARP requests for IPs that exist outside of its network. For example if my network is: Network: 8.8.8.0/24 Gateway: 8.8.8.1 (MAC: 00:21:9b:aa:aa:aa) Example Server: 8.8.8.20 (MAC: 00:21:9b:bb:bb:bb) By running a capture on the interface that has 8.8.8.1 I see requests like: Sender Mac: 00:21:9b:bb:bb:bb Sender IP: 8.8.8.20 Target MAC: 00:21:9b:aa:aa:aa Target IP: 69.63.181.58 Anyone seen this behavior before? My understanding of ARP is that requests should only go out for IPs within the subnet... Am I confused in my understanding of ARP? If I am not confused, anyone seen this behavior? Also, these seem to happen in bursts and it doesn't happen when I do something like ping an IP outside of the network. Update: In response to Ian's questions. I am not running anything like Hyper-V. I have multiple interfaces but only one is active (Using BACS failover teaming). The subnet mask is 255.255.255.0 (Even if it were something different it wouldn't explain an IP like 69.63.181.58). When I run MS Network Monitor or wireshark I do not see these ARP requests. What happens is that on the router capturing I see a burst of about 10 requests for IPs outside of the network from the host machine. On the machine itself using wireshark or NetMon I see a flood of ARP responses for all the machines on the network. However, I don't see any requests in the capture asking for those responses. So it seems like maybe it is maybe refreshing the arp cache but including IPs that outside of the network. Also when it does this NetMon doesn't show the ARP requests?

  Read the article

• Home network with two isolated separate subnets, running on cablemodem/router and WRT-router.

  - by Johan Allgoth

  I have a new connection with a nice new router/cable-modem. I'd like to setup it up optimally and needs some pointers. I am a complete n00b when it comes to routing. I want to end up with two separate subnets, 10.1.2.0/24 and 192.168.1.0/24 each available on their own wireless channel/SSID. Both firewalled. I want my wired computers on the gigabit switch, optimally with public ips. I want to be able to reach 192.168.1.0/24 from 10.1.2.0/24, but not vice versa. Everyone should have internet access. Hardware and capabilities: Netgear CG3100. Handles cable connection. Gigabit switch. 802.11n. Can do DHCP, firewall, NAT etc. Can choose subnet. Can turn of NAT and if so hand out up to 4 public ips. Somewhat challenged when it comes to configuration. WRT-router. Runs DD/Open-WRT very stable. 100 Mbit switch. 802.11.g Can do DHCP, firewall, NAT etc. Can choose subnet. Highly configurable. I hope to be able to keep 10.1.2.0/24 on the CG3100, for speed reasons and 192.168.0.0/24 on the WRT-router for quota and user control reasons. On my 10.1.2.0/24 network I plan on running servers for various services. Should I turn of NAT on the WRT-router? Or on the cable modem? Activate what in that case? Is double NAT always f-ed up?

  Read the article

• Dovecot authentification not working

  - by user1488723

  I run a Ubuntu 10.04 VPS with Postfix and Dovecot installed. For a while I had problems with the mailserver itself (Postfix) but now it runs ok. I can telnet into it from localhost (telnet localhost 25 while logged in) and Im blocked if I try to do it from the outside (telnet mail.example.org 25). This is as it should be according to my main.cf However when I try to log in using Dovecot (openssl s_client -connect mail.example.com:993) I'm allowed in but denied when trying to identify myself as a user: Excerpt from Dovecot log in: Key-Arg : None Start Time: 1341074622 Timeout : 300 (sec) Verify return code: 18 (self signed certificate) OK [CAPABILITY IMAP4rev1 LITERAL+ SASL-IR LOGIN-REFERRALS ID ENABLE AUTH=PLAIN AUTH=LOGIN] Dovecot ready. When I continue and try to log in to a specific user with the command: A001 login user password I get: A001 NO [AUTHENTICATIONFAILED] Authentication failed. I've reset the password to ensure it is correct and I know the user (user) exists on the system. When I do /etc/init.d/dovecot reload I get: /etc/init.d/dovecot: 29: maildir:~/Maildir: not found * Reloading IMAP/POP3 mail server dovecot [ OK ] Could it be that the mailboxes isn't found? Postfix main.cf: home_mailbox = Maildir/ mailbox_command = recipient_delimiter = + inet_interfaces = all smtpd_use_tls = yes smtpd_tls_auth_only = no smtpd_tls_loglevel = 1 smtpd_tls_cert_file = /etc/postfix/ssl/smtpd.crt smtpd_tls_key_file = /etc/postfix/ssl/smtpd.key smtpd_tls_CAfile = /etc/postfix/ssl/cacert.pem smtpd_sasl_auth_enable = yes smtpd_client_restrictions = permit_sasl_authenticated, permit_mynetworks, reject_unauth_destination smtpd_sender_restrictions = permit_sasl_authenticated, permit_mynetworks smtpd_recipient_restrictions = permit_mynetworks, permit_sasl_authenticated, reject_unauth_destination broken_sasl_auth_clients = yes smtpd_sasl_type = dovecot smtpd_sasl_path = private/auth smtpd_sasl_security_options = noanonymous smtpd_sasl_local_domain = $mydomain Dovecot.conf: protocols = imap imaps disable_plaintext_auth = no log_timestamp = "%b %d %H:%M:%S " ssl = yes ssl_cert_file = /etc/postfix/ssl/smtpd.crt ssl_key_file = /etc/postfix/ssl/smtpd.key mail_location = maildir:~/Maildir auth_verbose = yes mail_access_groups = mail auth_username_chars = abcdefghijklmnopqrstuvwxyz0123456789 protocol imap { imap_client_workarounds = delay-newmail tb-extra-mailbox-sep } auth default { mechanisms = plain login passdb pam { } userdb passwd { } socket listen { client { path = /var/spool/postfix/private/auth user = postfix group = postfix mode = 0660 } } }

  Read the article

• Postfix + SASLAUTHD + MySQL authentication problems

  - by Or W

  I've been trying to sort this out for the past 6 hours or so, this is the error message I'm facing (Running CentOS x64): /var/log/maillog: Jun 22 20:42:49 ptroa postfix/smtpd[10130]: warning: SASL authentication failure: Password verification failed Jun 22 20:42:49 ptroa postfix/smtpd[10130]: warning: bzq-79-177-192-133.red.bezeqint.net[79.177.192.133]: SASL PLAIN authentication failed: authentication failure Jun 22 20:42:49 ptroa postfix/smtpd[10130]: warning: bzq-79-177-192-133.red.bezeqint.net[79.177.192.133]: SASL LOGIN authentication failed: authentication failure /var/log/messages: Jun 22 20:15:38 ptroa saslauthd[9401]: do_auth : auth failure: [user=myuser] [service=smtp] [realm=domain.com] [mech=pam] [reason=PAM auth error] I have dovecot installed as well and I'm able to receive emails via the MySQL authentication. The problem is when I'm trying to use SMTP to send out emails. Some config files: /etc/postfix/main.cf: # See /usr/share/postfix/main.cf.dist for a commented, more complete version # Debian specific: Specifying a file name will cause the first # line of that file to be used as the name. The Debian default # is /etc/mailname. myorigin = /etc/mailname smtpd_banner = Server Message biff = no # appending .domain is the MUA's job. append_dot_mydomain = no # Uncomment the next line to generate "delayed mail" warnings #delay_warning_time = 4h readme_directory = /usr/share/doc/postfix # TLS parameters smtpd_tls_cert_file = /etc/postfix/smtpd.cert smtpd_tls_key_file = /etc/postfix/smtpd.key smtpd_use_tls = yes smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache # See /usr/share/doc/postfix/TLS_README.gz in the postfix-doc package for # information on enabling SSL in the smtp client. myhostname = domain.com alias_maps = hash:/etc/aliases alias_database = hash:/etc/aliases myorigin = /etc/mailname mydestination = relayhost = mynetworks = 127.0.0.0/8 [::ffff:127.0.0.0]/104 [::1]/128 mailbox_size_limit = 0 recipient_delimiter = + inet_interfaces = all html_directory = /usr/share/doc/postfix/html message_size_limit = 30720000 virtual_alias_domains = virtual_alias_maps = proxy:mysql:/etc/postfix/mysql-virtual_forwardings.cf, mysql:/etc/postfix/mysql-virtual_email2email.cf virtual_mailbox_domains = proxy:mysql:/etc/postfix/mysql-virtual_domains.cf virtual_mailbox_maps = proxy:mysql:/etc/postfix/mysql-virtual_mailboxes.cf virtual_mailbox_base = /home/vmail virtual_uid_maps = static:5000 virtual_gid_maps = static:5000 smtpd_sasl_auth_enable = yes broken_sasl_auth_clients = yes smtpd_sasl_authenticated_header = yes smtpd_recipient_restrictions = permit_mynetworks, permit_sasl_authenticated, reject_unauth_destination virtual_create_maildirsize = yes virtual_maildir_extended = yes proxy_read_maps = $local_recipient_maps $mydestination $virtual_alias_maps $virtual_alias_domains $virtual_mailbox_maps $virtual_mailbox_domains $relay_recipient_maps $relay_domains $canonical_maps $sender_canonical_maps $recipient_cano$ virtual_transport = dovecot dovecot_destination_recipient_limit = 1 /etc/default/saslauthd: START=yes DESC="SASL Authentication Daemon" NAME="saslauthd" MECHANISMS="pam" MECH_OPTIONS="" THREADS=5 OPTIONS="-c -m /var/spool/postfix/var/run/saslauthd -r" /etc/pam.d/smtp: #%PAM-1.0 #auth include password-auth #account include password-auth auth required pam_mysql.so user=mail_admin passwd=password host=127.0.0.1 db=mail table=users usercolumn=email passwdcolumn=password crypt=1 verbose=1 account sufficient pam_mysql.so user=mail_admin passwd=password host=127.0.0.1 db=mail table=users usercolumn=email passwdcolumn=password crypt=1 verbose=1

  Read the article

• HP Photosmart C4780 printer/scanner breaks netgear WNDR3700v3 router on connection

  - by CodeJunkie

  A few months ago, we upgraded our Netgear router's firmware. Immediately, we started having trouble connecting to the internet. Each time this problem would happen, every device in the house would stop being able to make new connections to the internet. For example, you couldn't open new pages in the browser, but if Skype was running when the problem happened, you could keep talking to people. The only solution to this problem seemed to be resetting the router to factory defaults. Eventually, we solved this problem by just downgrading the router firmware. A while later, we got a new Netgear router. Almost right away, the new router started having exactly the same problems as the old one did on current firmware. The network connection would stay active and the computer would say it had an internet connection, but you couldn't do anything online except for using Skype. We eventually figured out that this happens every time our HP printer gets onto the network. Any time the printer gets onto the wireless network, the whole network stops connecting to the internet almost completely. The only thing that will fix it at that point is to reset the router to factory specs, and unplug the printer so it can't get back onto the network. The Netgear router has the latest version of the firmware, but the printer/scanner is very old. It looks to me like this problem is probably a result of a firmware conflict between the printer and the router, but I'm not sure how to fix that problem. Here's some additional information: Printer: HP Photosmart C4780 Router: WNDR3700v3 Router firmware: V1.0.0.22_1.0.17 (Stock, up to date firmware) Why would the printer getting on the network cause the router to not be able to access the internet correctly until it was reset? What can be done to allow the printer to be on the network without breaking the network for all other devices? Edit: One other thing that happens during this internet problem is that multiple computers in the house display an "IP conflict" message repeatedly, and extremely frequently (as often as every five to ten minutes, and every time a connection to the wireless is made).

  Read the article

• How to configure Windows user accounts for ODBC network with NT authentication?

  - by Ian Mackinnon

  I'm trying to create a connection to an SQL Server database from the ODBC Data Source Administrator using "Windows NT authentication using the network login ID". Both server and client are running Windows XP. It appears that any account with administrator privileges can add the data source on the server*, though connection attempts from the client result in error messages that suggest it is trying to authenticate using a guest account. I found a Microsoft support page that says: For SQL Server...: connect using the impersonated user account. But it doesn't offer advice about how to do that. How do I impersonate a user account on the server? or (since it sounds like that would lead to an unfortuante squashing of privileges and loss of accountability): How do I give an account on the client privileges on the server database and then ensure the client attempts authentication with the privileged account and not with a guest account? I'm aware that I'm providing rather sparse information. This is because I'm in unfamiliar territory and don't know what's pertinent. I'll attempt to add any requested information as quickly as possible. *I'm planning on tightening privileges straight after I get it working as it stands.

  Read the article

• How to setup firewall to allow internet connection sharing via Wifi USB stick?

  - by hannanaha

  I have a Windows8 computer linked to the internet via an ethernet cable ("Ethernet" network connection). I have attached to it a DLink Wifi USB stick, and I'm trying to share the main PC's internet connection with my Android phone via a local wifi network. I am using the following batch file to set up this network: netsh wlan set hostednetwork mode=allow ssid=MyWifiName key=password keyUsage=persistent netsh wlan start hostednetwork After I run this script, I can see a new network connection appear in "Control Panel\Network and Internet\Network Connections" named "Local Area Connection *12", and I can see "MyWifiName" on the Android phone. The device name for this connection on the PC is "Microsoft Hosted Network Virtual Adapter". I also set up the "Ethernet" connection to share Internet with "Local Area Connection *12". However, the Android phone usually doesn't manage to obtain an IP from the wireless network, and when it does, there still seems to be no connectivity to the internet. When I turn off the Windows Firewall completely, or even just for "Local Area Connection *12", the Android connection is perfect. My questions are: How should I set up the Windows firewall to allow the phone to connect properly? Is there a specific rule I need to add to the Windows firewall advanced settings? [Note: the above method worked great in Windows 7, without any specific tinkering with the firewall]. Is it safe to turn off the firewall specifically for the "Local Area Connection *12" (the wifi connection) if the main Ethernet connection is still protected by the firewall? Thanks in advance.

  Read the article

• All network devices freezing when Airport Extreme Base Station is connected. Any ideas?

  - by Jon

  I've been troubleshooting this issue for a while, and through a series of events have it narrowed down to my airport extreme base station. I like this router, since I'm able to connect to IPV6 sites without any insane configuration (my alternate router is too old and doesn't support v6). My question is: Has anyone else had this issue, if so how is it resolved? If not, can you recommend a good IPv6 router? Here is how I came to the conclusion that it is the router: Devices: XBOX 360, HTC Incredible, Home-Built machine running FreeBSD, Home-Built machine running Ubuntu 10.04. 1.) Noticed freezing on Ubuntu Box. 2.) Noticed freezing on XBOX360 3.) Noticed freezing on HTC Incredible (only when connected to my network wirelessly). The above all happened at random times throughout the past few weeks. Over the last few days, I was playing XBOX and noticed that the XBOX and Ubuntu machines both froze. I picked up my phone, and it was also frozen. I reset all devices, power-cycled my router, and all was fine again. About two hours later, it happened again (I was playing Forza III, the XBOX froze; I went to the Ubuntu box and it was frozen; unfortunately, the HTC phone was not connected wirelessly, and the FreeBSD box was turned off). I can't even begin to imaging what a router could be doing to freeze devices with such differing hardware/software/OS, and I feel absurd for coming to this conclusion, but I have nothing else. I hooked up my archaic Netgear router, and have had no problems since. :(

  Read the article

• College network - can I point non-domain student computers to our SUS server?

  - by Joel Coel

  Since I started here 3 months ago, one of the things that's really bothered me about the way this network is setup is something that shows up on the daily bandwidth consumption report. I get a list of top-visited sites by hits and by size, and invariably the top site (to the point that it's bigger than all the other top sites combined) is au.download.windowsupdate.com. We're pulling in ~30GB/day in windows updates. This is every day, not just after a patch Tuesday. After a patch day, it jumps closer to 40GB for a couple days. The key here is that almost none if it is by machines that I'm responsible for. My machines are for the most part fully patched, and when they're not they'll pull from a SUS server, so new updates are downloaded only once. It used to be closer to 50GB/day because most of the machines in our computer labs use DeepFreeze and weren't applying updates correctly, but that's fixed now. So the problem is definitely student-owned machines in the dorms, some of which are re-downloading the same updates in background each day, over and over. I'd love to have these machines start pulling from our SUS server. Then, if they don't ever actually install them at least they're not leeching bandwidth from our public internet connection. Any ideas on how to resolve the situation?

  Read the article

• Hyper-V with multiple physical networks

  - by Yaman

  I have Hyper-V on my laptop with a wireless and Ethernet card, sometimes I connect using wireless card, and sometimes using the Ethernet cable. I am trying to configure Hyper-v to work always with internet provided to virtual machine. I have tried to create 2 virtual switches, one external to the Wireless network card, and the other one external to the Ethernet card. What happens is that the wireless network creates a bridge object in the network and sharing center\Network connections of windows 8, while the Ethernet does not. Unfortunately, they do not work together as external, i have to set the connected one to external and the other one as external, I also have to go to the properties of the bridge and virtual Ethernet properties to uncheck and check some components like: Client for Microsoft Networks Deterministic Network Enhancer VMWare Bridge Protocol QoS Packet Scheduler File and Printer Sharing for Microsoft Networks In order to make things work. Sometimes I keep the wireless network switch external, and go to another location (another wireless network), and it disconnects, i have to reconfigure the switches. Is there a way to do the configuration once and remain working wherever I connect, whether its Wireless or Ethernet and on any network with DHCP?

  Read the article

• heimdal error Decrypt integrity check failed for checksum type

  - by user880414

  when I try to authentication with heimdal-kdc ,I get this error in kdc log : (enctype aes256-cts-hmac-sha1-96) error Decrypt integrity check failed for checksum type hmac-sha1-96-aes256, key type aes256-cts-hmac-sha1-96 and authentication failed!!! but authentication with kinit is correct!! my kerb5.conf is [logging] default = FILE:/var/log/krb5libs.log kdc = FILE:/var/log/krb5kdc.log krb5 = FILE:/var/log/krb5.log [libdefaults] default_realm = AUTH.LANGHUA clockskew = 300 [realms] AUTH.LANGHUA = { kdc = AUTH.LANGHUA } [domain_realm] .langhua = AUTH.LANGHUA [kdc] and when add this line to krb5.conf (in kdc tag) require-preauth = no I get this error krb5_get_init_creds: Client have no reply key

  Read the article

• Vmware Workstation, Win7 host, Ubuntu guests with Nat + Host-only networks but they cannot connect to the Internet

  - by Ikon

  I have a Win7 host machine with Vmware Workstation. In the workstation I have 3 Ubuntu installed. All 3 Ubuntu guests have a Nat network - to access the internet without asking the router for a local address - and a Host-only network - to connect all Ubuntu quests and the host in a private network for internal communication, without touching the router. When I try to make any of the Ubuntu quests to get data from the internet - assuming that they would figure out that the Nat-ed interface can access the requested data - they fail and report that there is no route to my query. If I disconnect the 2nd interface on the Ubuntu guests with the Host-only network and restart networking, they start to know the route to the internet. Odd, during the installation of the guests they asked which of the 2 given interfaces - with Nat and Host-only config - should be used to get updates during installation and they oddly managed to get the updates. Not so after the installation has finished and rebooted. I have checked the Virtual Network Editor that the Nat interface should use my real network card to access the net, so there should be no problem. I wish not to use the router's dhcp service to give the Ubuntu quests an address, and also I don't want the guests to be accessable from the local network directly, but only by the host - that's the Host-only network is for. Any suggestions? Edit: 192.168.189.0 is the Nat interface and 192.168.7.0 is the Host-only. $ route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.7.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 192.168.189.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 0.0.0.0 192.168.189.2 0.0.0.0 UG 100 0 0 eth0

  Read the article

• I've got very brazen pop3 attack how to protect the server?

  - by Ken Tang

  Today I have brazen attack to my pop3-dovecot server and mail log is full over (200MB) with this kind of information: Nov 11 09:28:14 lax dovecot: pop3-login: Aborted login (auth failed, 1 attempts): user=<shawn>, method=PLAIN, rip=200.233.152.111, lip=myip Nov 11 09:28:14 lax dovecot: pop3-login: Aborted login (auth failed, 1 attempts): user=<shop>, method=PLAIN, rip=200.233.152.111, lip=myip Nov 11 09:28:14 lax dovecot: pop3-login: Aborted login (auth failed, 1 attempts): user=<sitetest>, method=PLAIN, rip=200.233.152.111, lip=myip Nov 11 09:28:14 lax dovecot: pop3-login: Aborted login (auth failed, 1 attempts): user=<solar>, method=PLAIN, rip=200.233.152.111, lip=myip Nov 11 09:28:15 lax dovecot: pop3-login: Aborted login (auth failed, 1 attempts): user=<services>, method=PLAIN, rip=200.233.152.111, lip=myip I just blocked attacker's ip by iptables -A INPUT -s 200.233.152.111 -j DROP But it this can be continued anytime from other ips. My question is: Is there any method to disallow anyone to connect my pop3 server (except only me?) because my ip is dynamic from ISP side so I don't know how to make pop3 server know that it is exactly me connecting to. Thank you in advance!

  Read the article

< Previous Page | 242 243 244 245 246 247 248 249 250 251 252 253  | Next Page >