Search Results

Search found 6949 results on 278 pages for 'loading'.

Page 249/278 | < Previous Page | 245 246 247 248 249 250 251 252 253 254 255 256  | Next Page >

• GRUB is not Booting Correctly

  - by msknapp

  I have a PC with three hard disks. Windows 7 is installed on the first, Ubuntu 14.04 is installed on the third. After I re-booted, it went straight to Windows 7. So I tried explicitly telling my PC to boot using the third hard disk, but that just takes me to the grub rescue prompt. I followed Scott Severence's instructions here to try and recover. Essentially, I updated grub, reinstalled grub, and then updated it again. After re-booting, absolutely nothing had changed. So instead I tried using the boot-repair tool. In the past it had failed for me, saying that I had programs running and it could not unmount drives, when I was running nothing. I never figured out how to solve that problem, but it went away when I bought another hard drive and used that for my Ubuntu installation, I don't know why. In any case, I ran the boot-repair tool and this time it said it was successful. First time for everything right? I re-booted, only to be taken straight to the grub rescue prompt. So I changed my BIOS settings to use the third hard disk for boot start up. That is the same hard drive where I have Ubuntu and grub installed, and the same one that the grub-repair tool told me to use. It still took me straight to the grub rescue prompt. So I went from not being able to boot Ubuntu, to not being able to boot either OS installed on my system. Thanks boot-repair! Boot repair gave me this URL for future troubleshooting: http://paste.ubuntu.com/8131669 When I try to boot from the third hard disk, this is my console: Loading Operating System ... error: attempt to read or write outside of disk 'hd0'. Entering rescue mode... grub rescue> grub rescue> set cmdpath=(hd0) prefix=(hd0,gpt2)/boot/grub root=hd0,gpt2 grub rescue> ls (hd0) (hd0,gpt3) (hd0,gpt2) (hd0,gpt1) (hd1) (hd2) (hd2,gpt2) (hd2,gpt1) (hd3) Those values look correct to me. I have also experimented with changing some of those values, but 'insmod normal' always throws the same error. Somebody please tell me how to fix this. I have tried everything, reinstalling grub, and running boot-repair. =========================== Update: I think the problem might be that the ubuntu installer did not partition my hard disk correctly. I booted from live USB and then launched gparted and looked at how it partitioned things. This is what gparted says: Partition, File System, Size, Used, Unused, Flags /dev/sda1 (!), unknown, 1.00 MiB, ---, ---, bios_grub /dev/sda2, ext4, 2.71 TiB, 47.30 GiB, 2.67 TiB, /dev/sda3, linux-swap, 16.00 GiB, 0.00 B, 16.00 GiB, So that first line looks problematic. It is supposed to be the /boot partition. However, it was given only 1 MiB? I am assuming that MiB is actually supposed to mean megabyte, no idea why that 'i' is there. It also says the file system is unknown. I read the answer by andrew here, and he says he had to do a custom install, explicitly configuring the boot partition. So I think that maybe Ubuntu's installer has a bug in it, where it does not set up the boot partition correctly if you are not installing on the first hard disk in your computer. I am going to try reinstalling with a custom partition scheme. I read elsewhere (askubuntu won't let me post another link) that I don't even need a /boot partition any more. So instead of following Andrew's instructions ver batim, I'm first going to try having just two partitions: one for /, and another for my 16GB swap space. Both as primary partitions. The first will be formatted as ext4. If that doesn't work, I may try again using /boot. ======================== So I did my custom install with no /boot partition, and it did not work. When I rebooted, I had an error message saying that some address did not exist. So for the hundredth time, I booted from the live USB, and ran boot-repair. Now I get this message GPT detected. Please create a BIOS-Boot partition (>1MB, unformatted filesystem, bios_grub flag). This can be performed via tools such as Gparted. Then try again. I feel like I'm running in circles and nobody will help me.

  Read the article

• Quadratic Programming with Oracle R Enterprise

  - by Jeff Taylor-Oracle

       I wanted to use quadprog with ORE on a server running Oracle Solaris 11.2 on a Oracle SPARC T-4 server For background, see: Oracle SPARC T4-2 http://docs.oracle.com/cd/E23075_01/ Oracle Solaris 11.2 http://www.oracle.com/technetwork/server-storage/solaris11/overview/index.html quadprog: Functions to solve Quadratic Programming Problems http://cran.r-project.org/web/packages/quadprog/index.html Oracle R Enterprise 1.4 ("ORE") 1.4 http://www.oracle.com/technetwork/database/options/advanced-analytics/r-enterprise/ore-downloads-1502823.html Problem: path to Solaris Studio doesn't match my installation: $ ORE CMD INSTALL quadprog_1.5-5.tar.gz * installing to library \u2018/u01/app/oracle/product/12.1.0/dbhome_1/R/library\u2019 * installing *source* package \u2018quadprog\u2019 ... ** package \u2018quadprog\u2019 successfully unpacked and MD5 sums checked ** libs /opt/SunProd/studio12u3/solarisstudio12.3/bin/f95 -m64   -PIC  -g  -c aind.f -o aind.o bash: /opt/SunProd/studio12u3/solarisstudio12.3/bin/f95: No such file or directory *** Error code 1 make: Fatal error: Command failed for target `aind.o' ERROR: compilation failed for package \u2018quadprog\u2019 * removing \u2018/u01/app/oracle/product/12.1.0/dbhome_1/R/library/quadprog\u2019 $ ls -l /opt/solarisstudio12.3/bin/f95 lrwxrwxrwx   1 root     root          15 Aug 19 17:36 /opt/solarisstudio12.3/bin/f95 -> ../prod/bin/f90 Solution: a symbolic link: $ sudo mkdir -p /opt/SunProd/studio12u3 $ sudo ln -s /opt/solarisstudio12.3 /opt/SunProd/studio12u3/ Now, it is all good: $ ORE CMD INSTALL quadprog_1.5-5.tar.gz * installing to library \u2018/u01/app/oracle/product/12.1.0/dbhome_1/R/library\u2019 * installing *source* package \u2018quadprog\u2019 ... ** package \u2018quadprog\u2019 successfully unpacked and MD5 sums checked ** libs /opt/SunProd/studio12u3/solarisstudio12.3/bin/f95 -m64   -PIC  -g  -c aind.f -o aind.o /opt/SunProd/studio12u3/solarisstudio12.3/bin/ cc -xc99 -m64 -I/usr/lib/64/R/include -DNDEBUG -KPIC  -xlibmieee  -c init.c -o init.o /opt/SunProd/studio12u3/solarisstudio12.3/bin/f95 -m64  -PIC -g  -c -o solve.QP.compact.o solve.QP.compact.f /opt/SunProd/studio12u3/solarisstudio12.3/bin/f95 -m64  -PIC -g  -c -o solve.QP.o solve.QP.f /opt/SunProd/studio12u3/solarisstudio12.3/bin/f95 -m64   -PIC  -g  -c util.f -o util.o /opt/SunProd/studio12u3/solarisstudio12.3/bin/ cc -xc99 -m64 -G -o quadprog.so aind.o init.o solve.QP.compact.o solve.QP.o util.o -xlic_lib=sunperf -lsunmath -lifai -lsunimath -lfai -lfai2 -lfsumai -lfprodai -lfminlai -lfmaxlai -lfminvai -lfmaxvai -lfui -lfsu -lsunmath -lmtsk -lm -lifai -lsunimath -lfai -lfai2 -lfsumai -lfprodai -lfminlai -lfmaxlai -lfminvai -lfmaxvai -lfui -lfsu -lsunmath -lmtsk -lm -L/usr/lib/64/R/lib -lR installing to /u01/app/oracle/product/12.1.0/dbhome_1/R/library/quadprog/libs ** R ** preparing package for lazy loading ** help *** installing help indices   converting help for package \u2018quadprog\u2019     finding HTML links ... done     solve.QP                                html      solve.QP.compact                        html  ** building package indices ** testing if installed package can be loaded * DONE (quadprog) ====== Here is an example from http://cran.r-project.org/web/packages/quadprog/quadprog.pdf > require(quadprog) > Dmat <- matrix(0,3,3) > diag(Dmat) <- 1 > dvec <- c(0,5,0) > Amat <- matrix(c(-4,-3,0,2,1,0,0,-2,1),3,3) > bvec <- c(-8,2,0) > solve.QP(Dmat,dvec,Amat,bvec=bvec) $solution [1] 0.4761905 1.0476190 2.0952381 $value [1] -2.380952 $unconstrained.solution [1] 0 5 0 $iterations [1] 3 0 $Lagrangian [1] 0.0000000 0.2380952 2.0952381 $iact [1] 3 2 Here, the standard example is modified to work with Oracle R Enterprise require(ORE) ore.connect("my-name", "my-sid", "my-host", "my-pass", 1521) ore.doEval(   function () {     require(quadprog)   } ) ore.doEval(   function () {     Dmat <- matrix(0,3,3)     diag(Dmat) <- 1     dvec <- c(0,5,0)     Amat <- matrix(c(-4,-3,0,2,1,0,0,-2,1),3,3)     bvec <- c(-8,2,0)    solve.QP(Dmat,dvec,Amat,bvec=bvec)   } ) $solution [1] 0.4761905 1.0476190 2.0952381 $value [1] -2.380952 $unconstrained.solution [1] 0 5 0 $iterations [1] 3 0 $Lagrangian [1] 0.0000000 0.2380952 2.0952381 $iact [1] 3 2 Now I can combine the quadprog compute algorithms with the Oracle R Enterprise Database engine functionality: Scale to large datasets Access to tables, views, and external tables in the database, as well as those accessible through database links Use SQL query parallel execution Use in-database statistical and data mining functionality

  Read the article

• Migrating R Scripts from Development to Production

  - by Mark Hornick

  Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 “How do I move my R scripts stored in one database instance to another? I have my development/test system and want to migrate to production.” Users of Oracle R Enterprise Embedded R Execution will often store their R scripts in the R Script Repository in Oracle Database, especially when using the ORE SQL API. From previous blog posts, you may recall that Embedded R Execution enables running R scripts managed by Oracle Database using both R and SQL interfaces. In ORE 1.3.1., the SQL API requires scripts to be stored in the database and referenced by name in SQL queries. The SQL API enables seamless integration with database-based applications and ease of production deployment. Loading R scripts in the repository Before talking about migration, we’ll first introduce how users store R scripts in Oracle Database. Users can add R scripts to the repository in R using the function ore.scriptCreate, or SQL using the function sys.rqScriptCreate. For the sample R script     id <- 1:10     plot(1:100,rnorm(100),pch=21,bg="red",cex =2)     data.frame(id=id, val=id / 100) users wrap this in a function and store it in the R Script Repository with a name. In R, this looks like ore.scriptCreate("RandomRedDots", function () { line-height: 115%; font-family: "Courier New";">     id <- 1:10     plot(1:100,rnorm(100),pch=21,bg="red",cex =2)     data.frame(id=id, val=id / 100)) }) In SQL, this looks like begin sys.rqScriptCreate('RandomRedDots',  'function(){     id <- 1:10     plot(1:100,rnorm(100),pch=21,bg="red",cex =2)     data.frame(id=id, val=id / 100)   }'); end; / The R function ore.scriptDrop and SQL function sys.rqScriptDrop can be used to drop these scripts as well. Note that the system will give an error if the script name already exists. Accessing R scripts once they’ve been loaded If you’re not using a source code control system, it is possible that your R scripts can be misplaced or files modified, making what is stored in Oracle Database to only or best copy of your R code. If you’ve loaded your R scripts to the database, it is straightforward to access these scripts from the database table SYS.RQ_SCRIPTS. For example, select * from sys.rq_scripts where name='myScriptName'; From R, scripts in the repository can be loaded into the R client engine using a function similar to the following: ore.scriptLoad <- function(name) { query <- paste("select script from sys.rq_scripts where name='",name,"'",sep="") str.f <- OREbase:::.ore.dbGetQuery(query) assign(name,eval(parse(text = str.f)),pos=1) } ore.scriptLoad("myFunctionName") This function is also useful if you want to load an existing R script from the repository into another R script in the repository – think modular coding style. Just include this function in the body of the other function and load the named script. Migrating R scripts from one database instance to another To move a set of functions from one system to another, the following script loads the functions from one R script repository into the client R engine, then connects to the target database and creates the scripts there with the same names. scriptNames <- OREbase:::.ore.dbGetQuery("select name from sys.rq_scripts where name not like 'RQG$%' and name not like 'RQ$%'")$NAME for(s in scriptNames) { cat(s,"\n") ore.scriptLoad(s) } ore.disconnect() ore.connect("rquser","orcl","localhost","rquser") for(s in scriptNames) { cat(s,"\n") ore.scriptDrop(s) ore.scriptCreate(s,get(s)) } Best Practice When naming R scripts, keep in mind that the name can be up to 128 characters. As such, consider organizing scripts in a directory structure manner. For example, if an organization has multiple groups or applications sharing the same database and there are multiple components, use “/” to facilitate the function organization: line-height: 115%;">ore.scriptCreate("/org1/app1/component1/myFuntion1", myFunction1) ore.scriptCreate("/org1/app1/component1/myFuntion2", myFunction2) ore.scriptCreate("/org1/app2/component2/myFuntion2", myFunction2) ore.scriptCreate("/org2/app2/component1/myFuntion3", myFunction3) ore.scriptCreate("/org3/app2/component1/myFuntion4", myFunction4) Users can then query for all functions using the path prefix when looking up functions. /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-fareast-font-family:"Times New Roman"; mso-fareast-theme-font:minor-fareast; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;}

  Read the article

• Exiting a reboot loop

  - by user12617035

  If you're in a situation where the system is panic'ing during boot, you can use # boot net -s to regain control of your system. In my case, I'd added some diagnostic code to a (PCI) driver (that is used to boot the root filesystem). There was a bug in the driver, and each time during boot, the bug occurred, and so caused the system to panic: ... 000000000180b950 genunix:vfs_mountroot+60 (800, 200, 0, 185d400, 1883000, 18aec00) %l0-3: 0000000000001770 0000000000000640 0000000001814000 00000000000008fc %l4-7: 0000000001833c00 00000000018b1000 0000000000000600 0000000000000200 000000000180ba10 genunix:main+98 (18141a0, 1013800, 18362c0, 18ab800, 180e000, 1814000) %l0-3: 0000000070002000 0000000000000001 000000000180c000 000000000180e000 %l4-7: 0000000000000001 0000000001074800 0000000000000060 0000000000000000 skipping system dump - no dump device configured rebooting... If you're logged in via the console, you can send a BREAK sequence in order to gain control of the firmware's (OBP's) prompt. Enter Ctrl-Shift-[ in order to get the TELNET prompt. Once telnet has control, enter this: telnet> send brk You'll be presented with OBP's prompt: ok You then enter the following in order to boot into single-user mode via the network: ok boot net -s Note that booting from the network under Solaris will implicitly cause the system to be INSTALLED with whatever software had last been configured to be installed. However, we are using boot net -s as a "handle" with which to get at the Solaris prompt. Once at that prompt, we can perform actions as root that will let us back out our buggy driver (ok... MY buggy driver :-)) ...and replace it with the original, non-buggy driver. Entering the boot command caused the following output, as well as left us at the Solaris prompt (in single-user-mode): Sun Blade 1500, No Keyboard Copyright 1998-2004 Sun Microsystems, Inc. All rights reserved. OpenBoot 4.16.4, 1024 MB memory installed, Serial #53463393. Ethernet address 0:3:ba:2f:c9:61, Host ID: 832fc961. Rebooting with command: boot net -s Boot device: /pci@1f,700000/network@2 File and args: -s 1000 Mbps FDX Link up Timeout waiting for ARP/RARP packet Timeout waiting for ARP/RARP packet 4000 1000 Mbps FDX Link up Requesting Internet address for 0:3:ba:2f:c9:61 SunOS Release 5.10 Version Generic_118833-17 64-bit Copyright 1983-2005 Sun Microsystems, Inc. All rights reserved. Use is subject to license terms. Booting to milestone "milestone/single-user:default". Configuring devices. Using RPC Bootparams for network configuration information. Attempting to configure interface bge0... Configured interface bge0 Requesting System Maintenance Mode SINGLE USER MODE # Our goal is to now move to the directory containing the buggy driver and replace it with the original driver (that we had saved away before ever loading our buggy driver! :-) However, since we booted from the network, the root filesystem ("/") is NOT mounted on one of our local disks. It is mounted on an NFS filesystem exported by our install server. To verify this, enter the following command: # mount | head -1 / on my-server:/export/install/media/s10u2/solarisdvd.s10s_u2dvd/latest/Solaris_10/Tools/Boot remote/read/write/setuid/devices/dev=4ac0001 on Wed Dec 31 16:00:00 1969 As a result, we have to create a temporary mount point and then mount the local disk onto that mount point: # mkdir /tmp/mnt # mount /dev/dsk/c0t0d0s0 /tmp/mnt Note that your system will not necessarily have had its root filesystem on "c0t0d0s0". This is something that you should also have recorded before you ever loaded your.. er... "my" buggy driver! :-) One can find the local disk mounted under the root filesystem by entering: # df -k / Filesystem kbytes used avail capacity Mounted on /dev/dsk/c0t0d0s0 76703839 4035535 71901266 6% / To continue with our example, we can now move to the directory of buggy-driver in order to replace it with the original driver. Note that /tmp/mnt is prefixed to the path of where we'd "normally" find the driver: # cd /tmp/mnt/platform/sun4u/kernel/drv/sparcv9 # ls -l pci\* -rw-r--r-- 1 root root 288504 Dec 6 15:38 pcisch -rw-r--r-- 1 root root 288504 Dec 6 15:38 pcisch.aar -rwxr-xr-x 1 root sys 211616 Jun 8 2006 pcisch.orig # cp -p pcisch.orig pcisch We can now synchronize any in-memory filesystem data structures with those on disk... and then reboot. The system will then boot correctly... as expected: # sync;sync # reboot syncing file systems... done Sun Blade 1500, No Keyboard Copyright 1998-2004 Sun Microsystems, Inc. All rights reserved. OpenBoot 4.16.4, 1024 MB memory installed, Serial #xxxxxxxx. Ethernet address 0:3:ba:2f:c9:61, Host ID: yyyyyyyy. Rebooting with command: boot Boot device: /pci@1e,600000/ide@d/disk@0,0:a File and args: SunOS Release 5.10 Version Generic_118833-17 64-bit Copyright 1983-2005 Sun Microsystems, Inc. All rights reserved. Use is subject to license terms. Hostname: my-host NIS domain name is my-campus.Central.Sun.COM my-host console login: ...so that's how it's done! Of course, the easier way is to never write a buggy-driver... but.. then.. we all "have an eraser on the end of each of our pencils"... don't we ? :-) "...thank you... and good night..."

  Read the article

• If I were in a Silverlight focus group, here is ten things I would say.

  - by mbcrump

  Silverlight is a great product right off the shelf. I use it, love it and spend a lot of time helping the community understand it. This however, doesn’t mean that I don’t think that it can get better. If I were invited to a Microsoft Focus Group about Silverlight here is 10 things I would say:  We need more navigation templates. I’ve found (4) templates that Microsoft has released (Cosmo, Windows 7, Accent and JetPack). This number needs to be around 16. In order to get more people developing for Silverlight, we need to give them a variety of templates to get them off the ground quickly. Silverlight needs to ship with the next version of Windows. At least version 4 needs to be pre-installed on Windows going forward. It’s small, in its own sandbox and I cannot find a reason for it not to be included. Silverlight needs to run on more platforms.  iOS and Android are the key here. I think Microsoft should shoot for Android first since I believe Android will take the lead in the mobile market (at least for the short-term). It would also be great to see Microsoft use Silverlight as the focus on their new tablets / “AppleTV”. I would even invest in getting it working with Kinect. When creating a new project in Silverlight, we should have the option to create a Unit Test. Most Silverlight developers are not unit testing. If this is surprising to you then you need to get out and talk to more developers. I partially blame this on Microsoft. When you create a new ASP.NET MVC application, you simply put a check to create a Unit Test project. We need the same thing for Silverlight. We should steer the developer into the right direction. Design patterns such as MVVM need to be easier to implement in Silverlight solutions.  I’d go so far as to say that MVVM Light should ship with Visual Studio. With the project / item templates and code snippets, Laurent puts you into the right direction. This is the way that it should have been. Easy for the 9-5 developer to grasp. I believe the majority of developers use code behind because that’s what is in all the demos provided by Microsoft. They are not trying to write sucky code it is that they simply don’t know a better way.  The XAP Files should be obfuscated/unused references deleted by default when in “Release” mode. A better Silverlight experience starts with a smaller XAP file. The less that a user has to download is the better, even with the majority of people on broadband. I would also recommend built-in obfuscation by Microsoft. People are paranoid that they can rename the .zip and run it through reflector. Get rid of the boring install experiences. Here is a great write up on what I’m talking about. The default “Install Silverlight” and “Loading screens” suck. They suck bad. We need a choice of templates that a professional designer has created.  Silverlight needs to supports more image formats. For example: it would be great to use .gif’s without converting them to .png.    Switching between Blend 4 and VS2010 to develop a Silverlight application is a pain. Probably one of the biggest issues that I can’t think of a good solution for. It would be nice if VS2012 had the best of both worlds and you never have to leave VS. We need reporting controls with SSRS included with the Silverlight Toolkit. I can’t think of another control that we need built into the toolkit. It would also be helpful to have export to .xls, .pdf and .doc included with the control. I hope that this post will at least get a few people talking. Who knows, Microsoft could be working on these things right now. Thanks for reading!  Subscribe to my feed CodeProject

  Read the article

• Different fan behaviour in my laptop after upgrade, what to do now?

  - by student

  After upgrading from lubuntu 13.10 to 14.04 the fan of my laptop seems to run much more often than in 13.10. When it runs, it doesn't run continously but starts and stops every second. fwts fan results in Results generated by fwts: Version V14.03.01 (2014-03-27 02:14:17). Some of this work - Copyright (c) 1999 - 2014, Intel Corp. All rights reserved. Some of this work - Copyright (c) 2010 - 2014, Canonical. This test run on 12/05/14 at 21:40:13 on host Linux einstein 3.13.0-24-generic #47-Ubuntu SMP Fri May 2 23:30:00 UTC 2014 x86_64. Command: "fwts fan". Running tests: fan. fan: Simple fan tests. -------------------------------------------------------------------------------- Test 1 of 2: Test fan status. Test how many fans there are in the system. Check for the current status of the fan(s). PASSED: Test 1, Fan cooling_device0 of type Processor has max cooling state 10 and current cooling state 0. PASSED: Test 1, Fan cooling_device1 of type Processor has max cooling state 10 and current cooling state 0. PASSED: Test 1, Fan cooling_device2 of type LCD has max cooling state 15 and current cooling state 10. Test 2 of 2: Load system, check CPU fan status. Test how many fans there are in the system. Check for the current status of the fan(s). Loading CPUs for 20 seconds to try and get fan speeds to change. Fan cooling_device0 current state did not change from value 0 while CPUs were busy. Fan cooling_device1 current state did not change from value 0 while CPUs were busy. ADVICE: Did not detect any change in the CPU related thermal cooling device states. It could be that the devices are returning static information back to the driver and/or the fan speed is automatically being controlled by firmware using System Management Mode in which case the kernel interfaces being examined may not work anyway. ================================================================================ 3 passed, 0 failed, 0 warning, 0 aborted, 0 skipped, 0 info only. ================================================================================ 3 passed, 0 failed, 0 warning, 0 aborted, 0 skipped, 0 info only. Test Failure Summary ================================================================================ Critical failures: NONE High failures: NONE Medium failures: NONE Low failures: NONE Other failures: NONE Test |Pass |Fail |Abort|Warn |Skip |Info | ---------------+-----+-----+-----+-----+-----+-----+ fan | 3| | | | | | ---------------+-----+-----+-----+-----+-----+-----+ Total: | 3| 0| 0| 0| 0| 0| ---------------+-----+-----+-----+-----+-----+-----+ Here is the output of lsmod lsmod Module Size Used by i8k 14421 0 zram 18478 2 dm_crypt 23177 0 gpio_ich 13476 0 dell_wmi 12761 0 sparse_keymap 13948 1 dell_wmi snd_hda_codec_hdmi 46207 1 snd_hda_codec_idt 54645 1 rfcomm 69160 0 arc4 12608 2 dell_laptop 18168 0 bnep 19624 2 dcdbas 14928 1 dell_laptop bluetooth 395423 10 bnep,rfcomm iwldvm 232285 0 mac80211 626511 1 iwldvm snd_hda_intel 52355 3 snd_hda_codec 192906 3 snd_hda_codec_hdmi,snd_hda_codec_idt,snd_hda_intel snd_hwdep 13602 1 snd_hda_codec snd_pcm 102099 3 snd_hda_codec_hdmi,snd_hda_codec,snd_hda_intel snd_page_alloc 18710 2 snd_pcm,snd_hda_intel snd_seq_midi 13324 0 snd_seq_midi_event 14899 1 snd_seq_midi snd_rawmidi 30144 1 snd_seq_midi coretemp 13435 0 kvm_intel 143060 0 kvm 451511 1 kvm_intel snd_seq 61560 2 snd_seq_midi_event,snd_seq_midi joydev 17381 0 serio_raw 13462 0 iwlwifi 169932 1 iwldvm pcmcia 62299 0 snd_seq_device 14497 3 snd_seq,snd_rawmidi,snd_seq_midi snd_timer 29482 2 snd_pcm,snd_seq lpc_ich 21080 0 cfg80211 484040 3 iwlwifi,mac80211,iwldvm yenta_socket 41027 0 pcmcia_rsrc 18407 1 yenta_socket pcmcia_core 23592 3 pcmcia,pcmcia_rsrc,yenta_socket binfmt_misc 17468 1 snd 69238 17 snd_hwdep,snd_timer,snd_hda_codec_hdmi,snd_hda_codec_idt,snd_pcm,snd_seq,snd_rawmidi,snd_hda_codec,snd_hda_intel,snd_seq_device,snd_seq_midi soundcore 12680 1 snd parport_pc 32701 0 mac_hid 13205 0 ppdev 17671 0 lp 17759 0 parport 42348 3 lp,ppdev,parport_pc firewire_ohci 40409 0 psmouse 102222 0 sdhci_pci 23172 0 sdhci 43015 1 sdhci_pci firewire_core 68769 1 firewire_ohci crc_itu_t 12707 1 firewire_core ahci 25819 2 libahci 32168 1 ahci i915 783485 2 wmi 19177 1 dell_wmi i2c_algo_bit 13413 1 i915 drm_kms_helper 52758 1 i915 e1000e 254433 0 drm 302817 3 i915,drm_kms_helper ptp 18933 1 e1000e pps_core 19382 1 ptp video 19476 1 i915 I tried one answer to the similar question: loud fan on Ubuntu 14.04 and created a /etc/i8kmon.conf like the following: # Run as daemon, override with --daemon option set config(daemon) 1 # Automatic fan control, override with --auto option set config(auto) 1 # Status check timeout (seconds), override with --timeout option set config(timeout) 2 # Report status on stdout, override with --verbose option set config(verbose) 1 # Temperature thresholds: {fan_speeds low_ac high_ac low_batt high_batt} set config(0) {{0 0} -1 55 -1 55} set config(1) {{0 1} 50 60 55 65} set config(2) {{1 1} 55 80 60 85} set config(3) {{2 2} 70 128 75 128} With this setup the fan goes on even if the temperature is below 50 degree celsius (I don't see a pattern). However I get the impression that the CPU got's hotter in average than without this file. What changes from 13.10 to 14.04 may be responsible for this? If this is a bug, for which package I should report the bug?

  Read the article

• "Mega Menus" for SEO [duplicate]

  - by Thought Space Designs

  This question already has an answer here: How do I handle having to many links on a webpage because of my menu 4 answers I'm using the term "Mega Menus" loosely here. I'm redesigning my WordPress site (it's going to be responsive), and as part of the redesign, I was debating incorporating some sort of descriptive menu setup. For example, normal navigation drop down menus come in the form of unordered lists of links like so: <nav> <ul> <li> <a href="#">Link1</a> </li> <li> <a href="#">Link2</a> </li> <li> <a href="#">Link3</a> <ul> <li> <a href="#">Sub Link1</a> </li> <li> <a href="#">Sub Link2</a> </li> <li> <a href="#">Sub Link3</a> </li> </ul> </li> <li> <a href="#">Link4</a> </li> </ul> </nav> What I'm looking to do is build my drop down menus with more information than your standard menu. For example, I have a top level link named "Team", and under that link, I want to make a large drop down that contains head shots, headers (in the form of styled p tags) and brief (<100 words) descriptions of each team member (only 2 currently). I want to accompany this with a "Read More" link that takes you to their actual team page. This is just one example, of course, and the other top level links would also have descriptive drop downs in the same fashion. On mobile, I was planning on hiding the "mega menu", and delivering a standard unordered list of links. Here's what I was thinking for overall structure and syntax: <nav> <ul> <li> <a href="#">Home</a> </li> <li> <a href="#">About</a> </li> <li> <a href="#">Team</a> <ul> <!-- DESKTOP --> <li class="mega-menu row"> <a class="col-sm-6" href="#"> <div class="row"> <div class="col-sm-4"> <img src="#" alt="Team Member 1" /> </div> <div class="col-sm-8"> <p class="header">Team Member 1</p> <p>Short description goes here.</p> </div> </div> </a> <a class="col-sm-6" href="#"> <!-- OTHER TEAM MEMBER INFO --> </a> </li> <!-- END DESKTOP --> <!-- MOBILE --> <li> <a href="#">Team Member 1</a> </li> <li> <a href="#">Team Member 2</a> </li> <!-- END MOBILE --> </ul> </li> <li> <a href="#">Contact</a> </li> </ul> </nav> Can anybody think of any potential SEO ramifications of doing this? I'm not going to be loading these menus full of links, so it shouldn't hurt page rank, but what are the effects of having a good bit of text and maybe even forms within nav elements? Is there such a thing as overloading nav with HTML? EDIT: Here's an example of what the menu would look like rendered on desktop. I'm currently hovering the "Team" menu, but you can't see because my mouse went away when I took the screenshot. EDIT 2: This question is not a duplicate. I'm not going to have "too many" links in my menus. I'm wondering how having images and text inside of header navigation will affect my menus. Also, I don't just want "yes, this is bad" answers. Please cite your sources and be specific with reasoning.

  Read the article

• Roaming user profile issues on Server 2008

  - by Alicia White

  I thought I cleared a user's profile from 2008, but it keeps coming back. So, I was looking for the best way to clear a roaming profile in Server 2008, but I have been unable to find anything. But, I did see the post here: http://serverfault.com/questions/18724/user-profile-keeps-loading-temp-profile I wanted to add a comment to that post, but it was closed as not being related to sysadmin. But, I think it IS related because I dealt with precisely this same problem on our Wndows 2008 terminal server. Here was the issue: we have a user who was getting an "unable to load your roaming profile" type of error at logon in Windows 2008. Looking at the server, we could see her temp profile listed in the profile list while she was loggged (listed as a "temporary" and not a "roaming" profile). While she was logged on, a folder called C:\Users\Temp.DOMAIN existed in the users folder, but that disappeared as soon as she logged out. When this thing happened in 2003, we would clear the contents of the roaming profile folder & delete the temp folder in C:\Documents and Settings. The thing is, 2008 behaves a bit differently. Server 2008 created a new roaming profile folder in the roaming profile folder share: \SERVER\ProfileShare\UserName.V2 The local profile disappears from the profile list in System Properties, so there is no profile to clear Also the local profile folder, C:\Users\Temp.DOMAIN doesn't stay on the server when the user logs out, so we can't delete that as we would normally do when this sort of thing happens in Windows 2003 Despite all of this, every time the user logs back on, the frickin' Temp profile always comes back. One of my team-mates, who is much more experienced with 2008, said I should check the registry for the user's profile in this key (the users are listed by SID): HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\WindowsNT\CurrentVersion\ProfileList I saw the user's SID listed there, but it ended in .BAK. I checked several other servers where she is having the same profile errors: in all cases, her SID ended with .BAK. For example (xxx replacing the LONG SID): HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows NT\CurrentVersion\ProfileList\S-1-5-21-xxxxx-xxxx.bak On the server she was logged on to, there were two keys for her profile in the registry: HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows NT\CurrentVersion\ProfileList\S-1-5-21-xxxxx-xxxx and HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows NT\CurrentVersion\ProfileList\S-1-5-21-xxxxx-xxxx.bak So, here is how I cleared up the issue. I had the user log off. I deleted the apparently bad profiles ending in .BAK from the ProfileList key on each server where it appeared. I made sure her roaming profile folder was empty I made sure that all the TEMP profile folders were gone The user logged back on: no more profile errors! Anyway, I wanted to make a comment on that closed question, but I didn't see any way to re-open the question so I could add it. But, I also would like to know if this is the best practice to clear out a bad roaming profile for Server 2008? I'm having a hard time finding any instructions on line on how best to do this, but this method I used seemed to work. I'd like to find some documentation to give to our Level 1 support staff so they will know how to clear user profiles on 2008 since this seems to be more involved that clearing user profiles in server 2003. Thanks, Alicia

  Read the article

• Weird networking problem ( Linksys, Windows 7 )

  - by Rohit Nair

  Okay it's a bit tough to figure out where to start from, but here is the basic summary of the issue: During general internet usage, there are times when any attempt to visit a website stalls at "Waiting for somedomain.com". This problem occurs in Firefox, IE and Chrome. No website will load, INCLUDING the router configuration page at 192.168.1.1. Curiously, ping works fine, and other network apps such as MSN Messenger continue to work and I can send and receive messages. Disconnecting and reconnecting to the wireless network seems to fix the problem for a bit, but there are times when it relapses into not loading after every 2-3 http requests. Restarting the router seems to fix the issue, but it can crop up hours or days later. I have a CCNA cert and I know my way around the Windows family of operating systems, so I'm going to list all the things I've tried here. Other computers on the network seem to suffer the same problem, which makes me think it might be a specific problem with something in Win7. The random nature of this issue makes it a bit difficult to confirm, but I can definitely say that I have experienced this on the following systems: Windows 7 64-bit on my desktop Windows Vista 32-bit on my desktop ( the desktop has 2 wireless NICs and the problem existed on both ) Windows Vista 32-bit on my laptop ( both with wireless and wired ) Windows XP SP3 on another laptop ( both wireless and wired ) Using Wireshark to sniff packets seemed to indicate that although HTTP requests were being SENT out, no packets were coming in to respond to the HTTP request. However, other network apps continued to work i.e I would still receive IMs on Windows Live Messenger. Disabling IPV6 had no effect. Updating router firmware to the latest stock firmware by Linksys had no effect. Switching to dd-wrt firmware had no effect. By "no effect" I mean that although the restart required by firmware updates fixed the problem at the time, it still came back. A couple of weeks back, after a LOT of googling and flipping of various options, I figured it might be a case of router slowdown ( http://www.dd-wrt.com/wiki/index.php/Router%5FSlowdown ) caused by the fact that I occasionally run a torrent client. I tried changing the configuration as suggested in that router slowdown link, and restarted the router. However I have not run the torrent client for 12 days now, and yet I still randomly experience this problem. Currently the computer I am using is running Windows 7 64-bit. I would just like to reiterate some of the reasons that I was confused by the issue. Even the router config page at 192.168.1.1 would not load, indicating that it's not a problem with the WAN link, but probably a router issue or a local computer issue. For some reason, disconnecting and reconnecting to the wireless network immediately seems to fix the problem. Updating the router firmware, even switching to open source firmware did nothing. So it seemed to be a computer issue. On the other hand, I have not seen any mass outrage of people having networking problems with Windows 7 and Linksys routers, especially a problem of this sort, and I have tweaked every network setting I could think of. Although HTTP seems to have trouble, ping works fine, DNS lookups work fine, other networking apps work fine. However if I disconnect from Windows Live Messenger and try to reconnect, it fails to reconnect. So although it could receive data over the existing TCP/IP connection, trying to start a new one failed? Does anyone have any further ideas on debugging or fixing this issue? I am reasonably certain there are no viruses or other malicious apps on my network, and I am also reasonably certain that nobody is accessing my router without my consent. Router: Linksys WRT54G2 1.0 running dd-wrt firmware Wireless Card: Alfa AWUS036H OS: Windows 7 64-bit EDIT: I tried switching to a clean wireless channel free from interference, but the problem still persisted. I tried connecting directly with a cable, but the problem still persisted. Signed A very confused and bewildered geek whose knowledge seems to be useless in the face of this frustrating network issue.

  Read the article

• What free space thresholds/limits are advisable for 640 GB and 2 TB hard disk drives with ZEVO ZFS on OS X?

  - by Graham Perrin

  Assuming that free space advice for ZEVO will not differ from advice for other modern implementations of ZFS … Question Please, what percentages or amounts of free space are advisable for hard disk drives of the following sizes? 640 GB 2 TB Thoughts A standard answer for modern implementations of ZFS might be "no more than 96 percent full". However if apply that to (say) a single-disk 640 GB dataset where some of the files most commonly used (by VirtualBox) are larger than 15 GB each, then I guess that blocks for those files will become sub optimally spread across the platters with around 26 GB free. I read that in most cases, fragmentation and defragmentation should not be a concern with ZFS. Sill, I like the mental picture of most fragments of a large .vdi in reasonably close proximity to each other. (Do features of ZFS make that wish for proximity too old-fashioned?) Side note: there might arise the question of how to optimise performance after a threshold is 'broken'. If it arises, I'll keep it separate. Background On a 640 GB StoreJet Transcend (product ID 0x2329) in the past I probably went beyond an advisable threshold. Currently the largest file is around 17 GB –  – and I doubt that any .vdi or other file on this disk will grow beyond 40 GB. (Ignore the purple masses, those are bundles of 8 MB band files.) Without HFS Plus: the thresholds of twenty, ten and five percent that I associate with Mobile Time Machine file system need not apply. I currently use ZEVO Community Edition 1.1.1 with Mountain Lion, OS X 10.8.2, but I'd like answers to be not too version-specific. References, chronological order ZFS Block Allocation (Jeff Bonwick's Blog) (2006-11-04) Space Maps (Jeff Bonwick's Blog) (2007-09-13) Doubling Exchange Performance (Bizarre ! Vous avez dit Bizarre ?) (2010-03-11) … So to solve this problem, what went in 2010/Q1 software release is multifold. The most important thing is: we increased the threshold at which we switched from 'first fit' (go fast) to 'best fit' (pack tight) from 70% full to 96% full. With TB drives, each slab is at least 5GB and 4% is still 200MB plenty of space and no need to do anything radical before that. This gave us the biggest bang. Second, instead of trying to reuse the same primary slabs until it failed an allocation we decided to stop giving the primary slab this preferential threatment as soon as the biggest allocation that could be satisfied by a slab was down to 128K (metaslab_df_alloc_threshold). At that point we were ready to switch to another slab that had more free space. We also decided to reduce the SMO bonus. Before, a slab that was 50% empty was preferred over slabs that had never been used. In order to foster more write aggregation, we reduced the threshold to 33% empty. This means that a random write workload now spread to more slabs where each one will have larger amount of free space leading to more write aggregation. Finally we also saw that slab loading was contributing to lower performance and implemented a slab prefetch mechanism to reduce down time associated with that operation. The conjunction of all these changes lead to 50% improved OLTP and 70% reduced variability from run to run … OLTP Improvements in Sun Storage 7000 2010.Q1 (Performance Profiles) (2010-03-11) Alasdair on Everything » ZFS runs really slowly when free disk usage goes above 80% (2010-07-18) where commentary includes: … OpenSolaris has changed this in onnv revision 11146 … [CFT] Improved ZFS metaslab code (faster write speed) (2010-08-22)

  Read the article

• BIND DNS Master with Zerigo Slaves - BIND won't update the slave servers

  - by Anthony

  I've tried to resolve this myself and have looked through Google and Stack but haven't found the answer I'm looking for. Currently on a VPS server I have BIND DNS installed as a MASTER DNS Server. I use Zerigo's DNS service as SLAVE servers for public use: The Master doesn't receive queries - It's job is to simply create and modify DNS entries locally of which the SLAVE use to serve. Here is an excerpt of the BIND log, I set it to INFO event logging: 14-Apr-2012 23:00:00.234 general: info: received control channel command 'reload' 14-Apr-2012 23:00:00.234 general: info: loading configuration from 'C:\DNS\BIND\etc\named.conf' 14-Apr-2012 23:00:00.234 general: info: using default UDP/IPv4 port range: [1024, 65535] 14-Apr-2012 23:00:00.234 general: info: using default UDP/IPv6 port range: [1024, 65535] 14-Apr-2012 23:00:00.250 general: info: reloading configuration succeeded 14-Apr-2012 23:00:00.250 general: info: reloading zones succeeded 14-Apr-2012 23:16:22.750 xfer-out: info: client 174.36.24.251#47135: transfer of 'ajmakeup.com/IN': AXFR started 14-Apr-2012 23:16:22.750 xfer-out: info: client 174.36.24.251#47135: transfer of 'ajmakeup.com/IN': AXFR ended 14-Apr-2012 23:16:23.015 xfer-out: info: client 68.71.141.22#36212: transfer of 'ajmakeup.com/IN': AXFR started 14-Apr-2012 23:16:23.031 xfer-out: info: client 68.71.141.22#36212: transfer of 'ajmakeup.com/IN': AXFR ended As you can see there is no problem with Zerigo's DNS servers requesting new DNS data, when I force a reload that is; I don't believe, as per the way they are set as SLAVE, that they poll for changes. However the problem is the other way; the MASTER is not updating the SLAVE servers when reload is run (on the MASTER); it is a batch on a 15 minute timer. Below is my NAMED.CONF: key "rndc-key" { algorithm hmac-md5; secret "REMOVED FOR SECURITY"; }; acl "trusted" { 174.36.24.251/32; 68.71.141.22/32; localhost; }; options { version "not currently available"; directory "C:\DNS\BIND\etc"; allow-query { trusted; }; }; controls { inet 127.0.0.1 port 953 allow { 127.0.0.1; } keys { "rndc-key"; }; }; logging{ channel simple_log { file "C:\DNS\BIND\logging\bind.log" versions 3 size 5m; severity info; print-time yes; print-severity yes; print-category yes; }; category default{ simple_log; }; }; zone "ajmakeup.com" in { type master; file "c:\dns\BIND\zones\db.ajmakeup.com.txt"; allow-transfer { 174.36.24.251; 68.71.141.22; }; allow-update { none; }; }; Does my problem have something to do with 'allow-query' under options? You will notice that 'allow-transfer' is set explicitly on each DNS zone. In case you need it here is my RNDC.CONF: key "rndc-key" { algorithm hmac-md5; secret "REMOVED FOR SECURITY"; }; options { default-key "rndc-key"; default-server 127.0.0.1; default-port 953; }; server localhost { key "rndc-key"; }; Note: I am using WebsitePanel as my hosting panel and is such why it creates the zone enteries the way it does. Although I know I can change this behaviour, I do not wish to do so nor do I believe is the root of the problem. Thanks for your help.

  Read the article

• shell script over SSH ends unexpectedly after running 'ant build'

  - by YShin

  I wrote a shell script that runs on remote host to build source code with 'ant build' command, and then distribute the built binary to other servers. However, right after Ant build is over successfully(I can see the command line output saying Build was successful), the ssh session ends and whatever commands after 'ant build' does not get executed. I'm confused what might be cause of this behavior. I suspected that it might be because the 'ant build' command takes too long time, and SSH somehow quits itself after that long command. But I don't think that's correct since if I just do 'sleep 60' in place of 'ant build' command, it actually execute latter commands as intended. I'm new at shell programming, so I might have made some silly misassumption. Can someone provide a pointer to a possible cause of this problem? My shell script #!/bin/bash # Inject some variables ssh -T $SSH_USER@$SSH_URL "setenv REMOTE_BASE_DIR $REMOTE_BASE_DIR; setenv CASSANDRA_SRC_TAR_FILE $CASSANDRA_SRC_TAR_FILE; setenv CASSANDRA_SRC_DIR_NAME $CASSANDRA_SRC_DIR_NAME; setenv CLUSTER_SIZE $CLUSTER_SIZE; setenv REMOTE_REDEPLOY_SCRIPT $REMOTE_REDEPLOY_SCRIPT; /bin/bash" << 'EOF' export JAVA_HOME=/usr/lib/jvm/jdk1.7.0 cd $REMOTE_BASE_DIR/$CASSANDRA_SRC_DIR_NAME echo "## Building Cassandra source" ant clean build # Anything after this doesn't run echo "## Ant Build is over. Invoking redeploy script on remote nodes" # Invoke redeploy script for each node for (( i=0; i < CLUSTER_SIZE; i++)) do echo "## Invoking redeploy script on node-$i" done Command-line output ## Building Cassandra source Buildfile: /scratch/ISS/shin14/repos/apache-cassandra-2.0.8-src-0713/build.xml clean: [delete] Deleting directory /scratch/ISS/shin14/repos/apache-cassandra-2.0.8-src-0713/build/test [delete] Deleting directory /scratch/ISS/shin14/repos/apache-cassandra-2.0.8-src-0713/build/classes [delete] Deleting directory /scratch/ISS/shin14/repos/apache-cassandra-2.0.8-src-0713/src/gen-java [delete] Deleting directory /scratch/ISS/shin14/repos/apache-cassandra-2.0.8-src-0713/src/resources/org/apache/cassandra/config init: [mkdir] Created dir: /scratch/ISS/shin14/repos/apache-cassandra-2.0.8-src-0713/build/classes/main [mkdir] Created dir: /scratch/ISS/shin14/repos/apache-cassandra-2.0.8-src-0713/build/classes/thrift [mkdir] Created dir: /scratch/ISS/shin14/repos/apache-cassandra-2.0.8-src-0713/build/test/lib [mkdir] Created dir: /scratch/ISS/shin14/repos/apache-cassandra-2.0.8-src-0713/build/test/classes [mkdir] Created dir: /scratch/ISS/shin14/repos/apache-cassandra-2.0.8-src-0713/src/gen-java maven-ant-tasks-localrepo: maven-ant-tasks-download: maven-ant-tasks-init: maven-declare-dependencies: maven-ant-tasks-retrieve-build: init-dependencies: [echo] Loading dependency paths from file: /scratch/ISS/shin14/repos/apache-cassandra-2.0.8-src-0713/build/build-dependencies.xml check-gen-cli-grammar: gen-cli-grammar: [echo] Building Grammar /scratch/ISS/shin14/repos/apache-cassandra-2.0.8-src-0713/src/java/org/apache/cassandra/cli/Cli.g .... check-gen-cql2-grammar: gen-cql2-grammar: [echo] Building Grammar /scratch/ISS/shin14/repos/apache-cassandra-2.0.8-src-0713/src/java/org/apache/cassandra/cql/Cql.g ... check-gen-cql3-grammar: gen-cql3-grammar: [echo] Building Grammar /scratch/ISS/shin14/repos/apache-cassandra-2.0.8-src-0713/src/java/org/apache/cassandra/cql3/Cql.g ... build-project: [echo] apache-cassandra: /scratch/ISS/shin14/repos/apache-cassandra-2.0.8-src-0713/build.xml [javac] Compiling 43 source files to /scratch/ISS/shin14/repos/apache-cassandra-2.0.8-src-0713/build/classes/thrift [javac] Note: /scratch/ISS/shin14/repos/apache-cassandra-2.0.8-src-0713/interface/thrift/gen-java/org/apache/cassandra/thrift/Cassandra.java uses or overrides a deprecated API. [javac] Note: Recompile with -Xlint:deprecation for details. [javac] Note: Some input files use unchecked or unsafe operations. [javac] Note: Recompile with -Xlint:unchecked for details. [javac] Compiling 865 source files to /scratch/ISS/shin14/repos/apache-cassandra-2.0.8-src-0713/build/classes/main [javac] Note: Some input files use or override a deprecated API. [javac] Note: Recompile with -Xlint:deprecation for details. [javac] Note: Some input files use unchecked or unsafe operations. [javac] Note: Recompile with -Xlint:unchecked for details. createVersionPropFile: [mkdir] Created dir: /scratch/ISS/shin14/repos/apache-cassandra-2.0.8-src-0713/src/resources/org/apache/cassandra/config [propertyfile] Creating new property file: /scratch/ISS/shin14/repos/apache-cassandra-2.0.8-src-0713/src/resources/org/apache/cassandra/config/version.properties [copy] Copying 3 files to /scratch/ISS/shin14/repos/apache-cassandra-2.0.8-src-0713/build/classes/main build: BUILD SUCCESSFUL Total time: 32 seconds

  Read the article

• TS-7800 Hangs on bootup

  - by Reid

  I have a TS-7800, and it typically boots from the SD card inserted in it. When I tried to boot it up today, it hung on the syslog line. I am now having "Read only file system" problems. What has gone wrong? Bootup console: >> Copyright (c) 2008, Technologic Systems >> Booting from SD card... . . . . >> Booting to SD Card... INIT: version 2.86 booting Starting the hotplug events dispatcher: udevd. Synthesizing the initial hotplug events...done. Waiting for /dev to be fully populated...done. mount: can't find / in /etc/fstab or /etc/mtab Cleaning up ifupdown...rm: cannot remove `/etc/network/run/ifstate': Read-only file system Loading kernel modules...done. Checking all file systems... fsck 1.37 (21-Mar-2005) ... done. none on /dev/pts type devpts (rw,gid=5,mode=620) /etc/init.d/rcS: line 39: /tmp/.clean: Read-only file system Setting up networking...done. Setting up IP spoofing protection: rp_filter. Enabling packet forwarding...done. Configuring network interfaces...ifup: failed to open statefile /etc/network/run/ifstate: Read-only file system done. Starting portmap daemon: portmap. /etc/init.d/rcS: line 39: /tmp/.clean: Read-only file system /etc/init.d/rcS: line 24: /var/run/utmp: Read-only file system rm: cannot remove `/var/lib/urandom/random-seed': Read-only file system urandom start: failed. Recovering nvi editor sessions... done. INIT: Entering runlevel: 3 Starting system log daemon: syslogd . Starting kernel log daemon: klogd. Starting MTA: open: Read-only file system touch: cannot touch `/var/lib/exim4/config.autogenerated.tmp': Read-only file system chown: cannot access `/var/lib/exim4/config.autogenerated.tmp': No such file or directory chmod: cannot access `/var/lib/exim4/config.autogenerated.tmp': No such file or directory chmod: changing permissions of `/var/lib/exim4/config.autogenerated': Read-only file system /usr/sbin/update-exim4.conf: line 260: cannot create temp file for here document: Read-only file system /usr/sbin/update-exim4.conf: line 387: /var/lib/exim4/config.autogenerated.tmp: Read-only file system 2002-01-01 01:31:36 Cannot open main log file "/var/log/exim4/mainlog": Read-only file system: euid=0 egid=0 2002-01-01 01:31:36 non-existent configuration file(s): /var/lib/exim4/config.autogenerated.tmp 2002-01-01 01:31:36 Cannot open main log file "/var/log/exim4/mainlog": Read-only file system: euid=0 egid=0 exim: could not open panic log - aborting: see message(s) above Invalid new configfile /var/lib/exim4/config.autogenerated.tmp not installing /var/lib/exim4/config.autogenerated.tmp to /var/lib/exim4/config.autogenerated Starting internet superserver: inetd. Starting OpenBSD Secure Shell server: sshd. Starting NFS common utilities: statdStarting periodic command scheduler: cron/usr/sbin/cron: can't open or create /var/run/crond.pid: Read-only file system . Starting web server (apache2)...(30)Read-only file system: apache2: could not open error log file /var/log/apache2/error.log. Unable to open logs failed! Debian GNU/Linux 3.1 ts7800 ttyS0 ts7800 login:

  Read the article

• Diagnosing Solaris 8 server memory and swap space usage

  - by datSilencer

  Hello everyone. Essentially, my question is related to memory allocation for Solaris virtual machines. I am running a couple of old Sun ONE 6 Java web servers on two Solaris 8 virtual machines. I see that there's a reasonable amount of swap space being used, but I'm not exactly sure if this could indicate a need to add more RAM to these machines. At service peak hours (mornings usually), the response time of the web application these servers host jumps up to at most 11 seconds (somewhat detrimental for a relatively simple web page loading action). Average response time at non peak times is about 5 seconds. What would you be able to infer about the RAM usage for these machines from the ouput below? Is this information reasonably sufficient? Or would I need to run some other commands to rule out server memory starvation? Finally, since there is a Java application at the core of the setup, I've also thought about: 1) Trace the heap's Object allocation to detect potential memory leaks. 2) Do some performance profiling to see if this instead related to networking delays. I mention this since the application talks with a single Oracle Database, but I would doubt this to be the case since they're pretty close from a network segmentation perspective. I appreciate any kind of insight and feedback you could provide. Thanks for your time and help. Server 1: 40 processes: 38 sleeping, 1 zombie, 1 on cpu CPU states: 99.1% idle, 0.4% user, 0.4% kernel, 0.0% iowait, 0.0% swap Memory: 2048M real, 295M free, 865M swap in use, 3788M swap free PID USERNAME THR PRI NICE SIZE RES STATE TIME CPU COMMAND 12676 webservd 112 29 10 616M 242M sleep 103:37 0.48% webservd 18317 root 1 59 0 23M 19M sleep 67:24 0.08% perl 9479 support 1 59 0 6696K 2448K cpu/1 0:11 0.05% top 8012 root 10 59 0 34M 704K sleep 80:54 0.04% java 1881 root 33 29 10 110M 13M sleep 33:03 0.02% webservd 7808 root 1 59 0 83M 67M sleep 7:59 0.00% perl 1461 root 20 59 0 5328K 1392K sleep 6:49 0.00% syslogd 1691 root 2 59 0 27M 680K sleep 4:22 0.00% webservd 24386 root 1 59 0 15M 11M sleep 2:50 0.00% perl 23259 root 1 59 0 11M 4240K sleep 2:42 0.00% perl 24718 root 1 59 0 11M 5464K sleep 2:29 0.00% perl 22810 root 1 59 0 19M 11M sleep 2:21 0.00% perl 24451 root 1 53 2 11M 3800K sleep 2:18 0.00% perl 18501 root 1 56 1 11M 3960K sleep 2:18 0.00% perl 14450 root 1 56 1 15M 6920K sleep 1:49 0.00% perl Server 2 42 processes: 40 sleeping, 1 zombie, 1 on cpu CPU states: 98.8% idle, 0.4% user, 0.8% kernel, 0.0% iowait, 0.0% swap Memory: 1024M real, 31M free, 554M swap in use, 3696M swap free PID USERNAME THR PRI NICE SIZE RES STATE TIME CPU COMMAND 5607 webservd 74 29 10 284M 173M sleep 20:14 0.21% webservd 15919 support 1 59 0 4056K 2520K cpu/1 0:08 0.09% top 13138 root 10 59 0 34M 1952K sleep 210:51 0.08% java 13753 root 1 59 0 22M 12M sleep 170:15 0.07% perl 22979 root 33 29 10 112M 7864K sleep 85:07 0.04% webservd 22930 root 1 59 0 3424K 1552K sleep 17:47 0.01% xntpd 22978 root 2 59 0 27M 2296K sleep 10:49 0.00% webservd 13571 root 1 59 0 9400K 5112K sleep 5:52 0.00% perl 5606 root 2 29 10 29M 9056K sleep 0:36 0.00% webservd 15910 support 1 59 0 9128K 2616K sleep 0:00 0.00% sshd 13106 root 1 59 0 82M 3520K sleep 7:47 0.00% perl 13547 root 1 59 0 12M 5528K sleep 6:38 0.00% perl 13518 root 1 59 0 9336K 3792K sleep 6:24 0.00% perl 13399 root 1 56 1 8072K 3616K sleep 5:18 0.00% perl 13557 root 1 53 2 8248K 3624K sleep 5:12 0.00% perl

  Read the article

• how to uninstall mariadb and re-install mysql ? Mysql install turns into mariadb install

  - by Suma

  I recently upgraded my centos system via the desktop. mistake! I had mariadb, phpmyadmin working just fine before - but after the upgrade they stopped. I frantically googled and tried to follow some tutorials about mariadb * mysql reinstall untill I came to this one: http://centosforge.com/node/how-replace-mysql-mariadb-centos-6-including-mysql-uninstall-instructions-and-yum-install I executed this command to remove all of mysql: yum remove mysql-server mysql-libs mysql-devel mysql* and then tried to reinstall mysql: as below - it crashes with errors as follows: ***************************************************************** [root@localhost ~]# yum install mysql-server mysql mysql-devel ***************************************************************** Loaded plugins: fastestmirror Loading mirror speeds from cached hostfile * base: centos.serverspace.co.uk * extras: centos.serverspace.co.uk * rpmforge: www.mirrorservice.org * updates: mirror.rmg.io Setting up Install Process Package mysql-server is obsoleted by MariaDB-server, trying to install MariaDB-server-5.5.29-1.i686 instead Package mysql is obsoleted by MariaDB-server, trying to install MariaDB-server-5.5.29-1.i686 instead Package mysql-devel is obsoleted by MariaDB-devel, trying to install MariaDB-devel-5.5.29-1.i686 instead Resolving Dependencies --> Running transaction check ---> Package MariaDB-devel.i686 0:5.5.29-1 set to be updated --> Processing Dependency: MariaDB-common for package: MariaDB-devel ---> Package MariaDB-server.i686 0:5.5.29-1 set to be updated --> Processing Dependency: libssl.so.10 for package: MariaDB-server --> Processing Dependency: libcrypto.so.10 for package: MariaDB-server --> Running transaction check ---> Package MariaDB-common.i686 0:5.5.29-1 set to be updated --> Processing Dependency: MariaDB-compat for package: MariaDB-common ---> Package MariaDB-server.i686 0:5.5.29-1 set to be updated --> Processing Dependency: libssl.so.10 for package: MariaDB-server --> Processing Dependency: libcrypto.so.10 for package: MariaDB-server --> Running transaction check ---> Package MariaDB-compat.i686 0:5.5.29-1 set to be updated ---> Package MariaDB-server.i686 0:5.5.29-1 set to be updated --> Processing Dependency: libssl.so.10 for package: MariaDB-server --> Processing Dependency: libcrypto.so.10 for package: MariaDB-server --> Finished Dependency Resolution MariaDB-server-5.5.29-1.i686 from mariadb has depsolving problems --> Missing Dependency: libcrypto.so.10 is needed by package MariaDB-server-5.5.29-1.i686 (mariadb) MariaDB-server-5.5.29-1.i686 from mariadb has depsolving problems --> Missing Dependency: libssl.so.10 is needed by package MariaDB-server-5.5.29-1.i686 (mariadb) Error: Missing Dependency: libcrypto.so.10 is needed by package MariaDB-server-5.5.29-1.i686 (mariadb) Error: Missing Dependency: libssl.so.10 is needed by package MariaDB-server-5.5.29-1.i686 (mariadb) You could try using --skip-broken to work around the problem You could try running: package-cleanup --problems package-cleanup --dupes rpm -Va --nofiles --nodigest [root@localhost ~] If I now try to install libssl.10, i get asked to install glibc libraries. 2.17 and 2.7 - other discussions have said to stay clear of the as this will explode my system - I tried download 2.17 and it's huge - took ages to unzip. Could someone please help me to completelty remove maraidb and install mysql - so that I don't get the above errors and pushed over to mariadb when I run: yum install mysql-server mysql mysql-devel There are tons of material on how to install mariadb - but none i found so far that plainly explains how to go backwards to mysql.

  Read the article

• Upgrading PHP from 5.1 to 5.2 on CentOS 5.4

  - by andufo

  i'm trying to upgrade php 5.1 to 5.2 on a CentOS 5.4 I use: yum upgrade php The result is this (check out the last part): [root@mail httpd]# yum update php Loaded plugins: fastestmirror Loading mirror speeds from cached hostfile * addons: mirror.raystedman.net * base: mirrors.serveraxis.net * centosplus: mirrors.tummy.com * contrib: mirror.raystedman.net * extras: mirror.raystedman.net * updates: mirrors.netdna.com Setting up Update Process Resolving Dependencies --> Running transaction check --> Processing Dependency: php = 5.1.6-27.el5 for package: php-devel --> Processing Dependency: php = 5.1.6 for package: php-eaccelerator ---> Package php.x86_64 0:5.2.10-1.el5.centos set to be updated --> Processing Dependency: php-cli = 5.2.10-1.el5.centos for package: php --> Processing Dependency: php-common = 5.2.10-1.el5.centos for package: php --> Running transaction check --> Processing Dependency: php = 5.1.6 for package: php-eaccelerator ---> Package php-cli.x86_64 0:5.2.10-1.el5.centos set to be updated --> Processing Dependency: php-common = 5.1.6-27.el5 for package: php-xml --> Processing Dependency: php-common = 5.1.6-27.el5 for package: php-pdo --> Processing Dependency: php-common = 5.1.6-27.el5 for package: php-gd --> Processing Dependency: php-common = 5.1.6-27.el5 for package: php-ldap --> Processing Dependency: php-common = 5.1.6-27.el5 for package: php-mbstring --> Processing Dependency: php-common = 5.1.6-27.el5 for package: php-mysql --> Processing Dependency: php-common = 5.1.6-27.el5 for package: php-imap ---> Package php-common.x86_64 0:5.2.10-1.el5.centos set to be updated ---> Package php-devel.x86_64 0:5.2.10-1.el5.centos set to be updated --> Running transaction check --> Processing Dependency: php = 5.1.6 for package: php-eaccelerator ---> Package php-gd.x86_64 0:5.2.10-1.el5.centos set to be updated ---> Package php-imap.x86_64 0:5.2.10-1.el5.centos set to be updated ---> Package php-ldap.x86_64 0:5.2.10-1.el5.centos set to be updated ---> Package php-mbstring.x86_64 0:5.2.10-1.el5.centos set to be updated ---> Package php-mysql.x86_64 0:5.2.10-1.el5.centos set to be updated ---> Package php-pdo.x86_64 0:5.2.10-1.el5.centos set to be updated ---> Package php-xml.x86_64 0:5.2.10-1.el5.centos set to be updated --> Finished Dependency Resolution php-eaccelerator-5.1.6_0.9.5.2-4.el5.rf.x86_64 from installed has depsolving problems --> Missing Dependency: php = 5.1.6 is needed by package php-eaccelerator-5.1.6_0.9.5.2-4.el5.rf.x86_64 (installed) Error: Missing Dependency: php = 5.1.6 is needed by package php-eaccelerator-5.1.6_0.9.5.2-4.el5.rf.x86_64 (installed) You could try using --skip-broken to work around the problem You could try running: package-cleanup --problems package-cleanup --dupes rpm -Va --nofiles --nodigest The program package-cleanup is found in the yum-utils package. [root@mail httpd]# What are the consequences of using --skip-broken? Any recommendations?

  Read the article

• PHP install sqlite3 extension

  - by Kevin

  We are using PHP 5.3.6 here, but we used the --without-sqlite3 command when compiling PHP. (It stands in the 'Configure Command' column). But, it is very risky to recompile PHP on that server; there are many visitors. How can we install/use sqlite3? Regards, Kevin [EDIT] yum repolist gives: Loaded plugins: fastestmirror Loading mirror speeds from cached hostfile * base: mirror.nl.leaseweb.net * extras: mirror.nl.leaseweb.net * updates: mirror.nl.leaseweb.net repo id repo name status base CentOS-5 - Base 3,566 extras CentOS-5 - Extras 237 updates CentOS-5 - Updates 376 repolist: 4,179 rpm -qa | grep php gives: php-pdo-5.3.6-1.w5 php-mysql-5.3.6-1.w5 psa-php5-configurator-1.5.3-cos5.build95101022.10 php-mbstring-5.3.6-1.w5 php-imap-5.3.6-1.w5 php-cli-5.3.6-1.w5 php-gd-5.3.6-1.w5 php-5.3.6-1.w5 php-common-5.3.6-1.w5 php-xml-5.3.6-1.w5 php -i | grep sqlite gives: PHP Warning: PHP Startup: Unable to load dynamic library '/usr/lib64/php/modules/sqlite3.so' - /usr/lib64/php/modules/sqlite3.so: cannot open shared object file: No such file or directory in Unknown on line 0 Configure Command => './configure' '--build=x86_64-redhat-linux-gnu' '--host=x86_64-redhat-linux-gnu' '--target=x86_64-redhat-linux-gnu' '--program-prefix=' '--prefix=/usr' '--exec-prefix=/usr' '--bindir=/usr/bin' '--sbindir=/usr/sbin' '--sysconfdir=/etc' '--datadir=/usr/share' '--includedir=/usr/include' '--libdir=/usr/lib64' '--libexecdir=/usr/libexec' '--localstatedir=/var' '--sharedstatedir=/usr/com' '--mandir=/usr/share/man' '--infodir=/usr/share/info' '--cache-file=../config.cache' '--with-libdir=lib64' '--with-config-file-path=/etc' '--with-config-file-scan-dir=/etc/php.d' '--disable-debug' '--with-pic' '--disable-rpath' '--without-pear' '--with-bz2' '--with-exec-dir=/usr/bin' '--with-freetype-dir=/usr' '--with-png-dir=/usr' '--with-xpm-dir=/usr' '--enable-gd-native-ttf' '--without-gdbm' '--with-gettext' '--with-gmp' '--with-iconv' '--with-jpeg-dir=/usr' '--with-openssl' '--with-pcre-regex=/usr' '--with-zlib' '--with-layout=GNU' '--enable-exif' '--enable-ftp' '--enable-magic-quotes' '--enable-sockets' '--enable-sysvsem' '--enable-sysvshm' '--enable-sysvmsg' '--with-kerberos' '--enable-ucd-snmp-hack' '--enable-shmop' '--enable-calendar' '--without-mime-magic' '--without-sqlite' '--without-sqlite3' '--with-libxml-dir=/usr' '--enable-xml' '--with-system-tzdata' '--enable-force-cgi-redirect' '--enable-pcntl' '--with-imap=shared' '--with-imap-ssl' '--enable-mbstring=shared' '--enable-mbregex' '--with-gd=shared' '--enable-bcmath=shared' '--enable-dba=shared' '--with-db4=/usr' '--with-xmlrpc=shared' '--with-ldap=shared' '--with-ldap-sasl' '--with-mysql=shared,/usr' '--with-mysqli=shared,/usr/bin/mysql_config' '--enable-dom=shared' '--with-pgsql=shared' '--enable-wddx=shared' '--with-snmp=shared,/usr' '--enable-soap=shared' '--with-xsl=shared,/usr' '--enable-xmlreader=shared' '--enable-xmlwriter=shared' '--with-curl=shared,/usr' '--enable-fastcgi' '--enable-pdo=shared' '--with-pdo-odbc=shared,unixODBC,/usr' '--with-pdo-mysql=shared,/usr' '--with-pdo-pgsql=shared,/usr' '--with-pdo-sqlite=shared,/usr' '--with-pdo-dblib=shared,/usr' '--enable-json=shared' '--enable-zip=shared' '--with-readline' '--with-pspell=shared' '--enable-phar=shared' '--with-mcrypt=shared,/usr' '--with-tidy=shared,/usr' '--with-mssql=shared,/usr' '--enable-sysvmsg=shared' '--enable-sysvshm=shared' '--enable-sysvsem=shared' '--enable-posix=shared' '--with-unixODBC=shared,/usr' '--enable-fileinfo=shared' '--enable-intl=shared' '--with-icu-dir=/usr' '--with-recode=shared,/usr' /etc/php.d/pdo_sqlite.ini, /etc/php.d/sqlite3.ini, PHP Warning: Unknown: It is not safe to rely on the system's timezone settings. You are *required* to use the date.timezone setting or the date_default_timezone_set() function. In case you used any of those methods and you are still getting this warning, you most likely misspelled the timezone identifier. We selected 'Europe/Berlin' for 'CET/1.0/no DST' instead in Unknown on line 0 PDO drivers => mysql, sqlite pdo_sqlite PWD => /root/sqlite _SERVER["PWD"] => /root/sqlite _ENV["PWD"] => /root/sqlite

  Read the article

• reiserfsck on lvm

  - by DaDaDom

  It seems like my filesystem got corrupted somehow during the last reboot of my server. I can't fsck some logical volumes anymore. The setup: root@rescue ~ # cat /mnt/rescue/etc/fstab proc /proc proc defaults 0 0 /dev/md0 /boot ext3 defaults 0 2 /dev/md1 / ext3 defaults,errors=remount-ro 0 1 /dev/systemlvm/home /home reiserfs defaults 0 0 /dev/systemlvm/usr /usr reiserfs defaults 0 0 /dev/systemlvm/var /var reiserfs defaults 0 0 /dev/systemlvm/tmp /tmp reiserfs noexec,nosuid 0 2 /dev/sda5 none swap defaults,pri=1 0 0 /dev/sdb5 none swap defaults,pri=1 0 0 [UPDATE] First question: what "part" should I check for bad blocks? The logical volume, the underlying /dev/md or the /dev/sdx below that? Is doing what I am doing the right way to go? [/UPDATE] The errormessage when checking /dev/systemlvm/usr: root@rescue ~ # reiserfsck /dev/systemlvm/usr reiserfsck 3.6.19 (2003 www.namesys.com) [...] Will read-only check consistency of the filesystem on /dev/systemlvm/usr Will put log info to 'stdout' Do you want to run this program?[N/Yes] (note need to type Yes if you do):Yes ########### reiserfsck --check started at Wed Feb 3 07:10:55 2010 ########### Replaying journal.. Reiserfs journal '/dev/systemlvm/usr' in blocks [18..8211]: 0 transactions replayed Checking internal tree.. Bad root block 0. (--rebuild-tree did not complete) Aborted Well so far, let's try --rebuild-tree: root@rescue ~ # reiserfsck --rebuild-tree /dev/systemlvm/usr reiserfsck 3.6.19 (2003 www.namesys.com) [...] Will rebuild the filesystem (/dev/systemlvm/usr) tree Will put log info to 'stdout' Do you want to run this program?[N/Yes] (note need to type Yes if you do):Yes Replaying journal.. Reiserfs journal '/dev/systemlvm/usr' in blocks [18..8211]: 0 transactions replayed ########### reiserfsck --rebuild-tree started at Wed Feb 3 07:12:27 2010 ########### Pass 0: ####### Pass 0 ####### Loading on-disk bitmap .. ok, 269716 blocks marked used Skipping 8250 blocks (super block, journal, bitmaps) 261466 blocks will be read 0%....20%....40%....60%....80%....100% left 0, 11368 /sec 52919 directory entries were hashed with "r5" hash. "r5" hash is selected Flushing..finished Read blocks (but not data blocks) 261466 Leaves among those 13086 Objectids found 53697 Pass 1 (will try to insert 13086 leaves): ####### Pass 1 ####### Looking for allocable blocks .. finished 0% left 12675, 0 /sec The problem has occurred looks like a hardware problem (perhaps memory). Send us the bug report only if the second run dies at the same place with the same block number. mark_block_used: (39508) used already Aborted Bad. But let's do it again as mentioned: [...] Flushing..finished Read blocks (but not data blocks) 261466 Leaves among those 13085 Objectids found 54305 Pass 1 (will try to insert 13085 leaves): ####### Pass 1 ####### Looking for allocable blocks .. finished 0%... left 12127, 958 /sec The problem has occurred looks like a hardware problem (perhaps memory). Send us the bug report only if the second run dies at the same place with the same block number. build_the_tree: Nothing but leaves are expected. Block 196736 - internal Aborted Same happens every time, only the actual error message changes. Sometimes I get mark_block_used: (somenumber) used already, other times the block number changes. Seems like something is REALLY broken. Are there any chances I can somehow get the partitions to work again? It's a server to which I don't have physical access directly (hosted server). Thanks in advance!

  Read the article

• virturalmin webmin dose not respond

  - by Miranda

  I have installed Virtualmin on a CentOS remote server, but it dose not seem to work https://115.146.95.118:10000/ at least the Webmin page dose not work. I have opened those ports http ALLOW 80:80 from 0.0.0.0/0 ALLOW 443:443 from 0.0.0.0/0 ssh ALLOW 22:22 from 0.0.0.0/0 virtualmin ALLOW 20000:20000 from 0.0.0.0/0 ALLOW 10000:10009 from 0.0.0.0/0 And restarting Webmin dose not solve it: /etc/rc.d/init.d/webmin restart Stopping Webmin server in /usr/libexec/webmin Starting Webmin server in /usr/libexec/webmin And I have tried to use Amazon EC2 this time, still couldn't get it to work. http://ec2-67-202-21-21.compute-1.amazonaws.com:10000/ [ec2-user@ip-10-118-239-13 ~]$ netstat -an | grep :10000 tcp 0 0 0.0.0.0:10000 0.0.0.0:* LISTEN udp 0 0 0.0.0.0:10000 0.0.0.0:* [ec2-user@ip-10-118-239-13 ~]$ sudo iptables -L -n Chain INPUT (policy ACCEPT) target prot opt source destination ACCEPT udp -- 0.0.0.0/0 0.0.0.0/0 udp dpt:20 ACCEPT udp -- 0.0.0.0/0 0.0.0.0/0 udp dpt:21 ACCEPT udp -- 0.0.0.0/0 0.0.0.0/0 udp dpt:53 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:20000 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:10000 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:443 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:80 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:993 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:143 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:995 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:110 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:20 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:21 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:53 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:587 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:25 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:22 Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination Since I need more than 10 reputation to post image, you can find the screenshots of the security group setting at the Webmin Support Forum. I have tried: sudo iptables -A INPUT -p tcp -m tcp --dport 10000 -j ACCEPT It did not change anything. [ec2-user@ip-10-118-239-13 ~]$ sudo yum install openssl perl-Net-SSLeay perl-Crypt-SSLeay Loaded plugins: fastestmirror, priorities, security, update-motd Loading mirror speeds from cached hostfile * amzn-main: packages.us-east-1.amazonaws.com * amzn-updates: packages.us-east-1.amazonaws.com amzn-main | 2.1 kB 00:00 amzn-updates | 2.3 kB 00:00 Setting up Install Process Package openssl-1.0.0j-1.43.amzn1.i686 already installed and latest version Package perl-Net-SSLeay-1.35-9.4.amzn1.i686 already installed and latest version Package perl-Crypt-SSLeay-0.57-16.4.amzn1.i686 already installed and latest version Nothing to do [ec2-user@ip-10-118-239-13 ~]$ nano /etc/webmin/miniserv.conf GNU nano 2.0.9 File: /etc/webmin/miniserv.conf port=10000 root=/usr/libexec/webmin mimetypes=/usr/libexec/webmin/mime.types addtype_cgi=internal/cgi realm=Webmin Server logfile=/var/webmin/miniserv.log errorlog=/var/webmin/miniserv.error pidfile=/var/webmin/miniserv.pid logtime=168 ppath= ssl=1 env_WEBMIN_CONFIG=/etc/webmin env_WEBMIN_VAR=/var/webmin atboot=1 logout=/etc/webmin/logout-flag listen=10000 denyfile=\.pl$ log=1 blockhost_failures=5 blockhost_time=60 syslog=1 session=1 server=MiniServ/1.585 userfile=/etc/webmin/miniserv.users keyfile=/etc/webmin/miniserv.pem passwd_file=/etc/shadow passwd_uindex=0 passwd_pindex=1 passwd_cindex=2 passwd_mindex=4 passwd_mode=0 preroot=virtual-server-theme passdelay=1 sessiononly=/virtual-server/remote.cgi preload= mobile_preroot=virtual-server-mobile mobile_prefixes=m. mobile. anonymous=/virtualmin-mailman/unauthenticated=anonymous ssl_cipher_list=ECDHE-RSA-AES256-SHA384:AES256-SHA256:AES256-SHA256:RC4:HIGH:MEDIUM:+TLSv1:!MD5:!SSLv2:+SSLv3:!ADH:!aNULL:!eNULL:!NULL:!DH:!ADH:!EDH:!AESGCM

  Read the article

• Is it possible to repair a Cisco 3500 XL (3548) switch with POST Error messages?

  - by Alex

  I've got an old Cisco 3500 XL, and it seems to have hardware issues. I've loaded the latest IOS and cleared all config. Does anyone have any experience fixing the switch core? I'm a reasonably competent SMD solderer, can I replace/reflow some chips? I've checked the power supply voltages and it's all within tolerance, and no visible signs of any component damage. Some chips are hot to the touch. I understand that these were EOL as of 2007, but should have a lifetime warranty for the electronics. I don't have a Cisco support contract, so I can't file a ticket. What should I do? Console output: switch: dir flash: Directory of flash:/ 2 -rwx 1811584 <date> c3500xl-c3h2s-mz.120-5.WC17.bin 1799680 bytes available (1812992 bytes used) switch: boot Loading "flash:c3500xl-c3h2s-mz.120-5.WC17.bin"...################################################################################################################################################################################### File "flash:c3500xl-c3h2s-mz.120-5.WC17.bin" uncompressed and installed, entry point: 0x3000 executing... Restricted Rights Legend Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (c) of the Commercial Computer Software - Restricted Rights clause at FAR sec. 52.227-19 and subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS sec. 252.227-7013. cisco Systems, Inc. 170 West Tasman Drive San Jose, California 95134-1706 Cisco Internetwork Operating System Software IOS (tm) C3500XL Software (C3500XL-C3H2S-M), Version 12.0(5)WC17, RELEASE SOFTWARE (fc1) Copyright (c) 1986-2007 by cisco Systems, Inc. Compiled Tue 13-Feb-07 15:04 by antonino Image text-base: 0x00003000, data-base: 0x00352924 Initializing C3500XL flash... flashfs[1]: 1 files, 1 directories flashfs[1]: 0 orphaned files, 0 orphaned directories flashfs[1]: Total bytes: 3612672 flashfs[1]: Bytes used: 1812992 flashfs[1]: Bytes available: 1799680 flashfs[1]: flashfs fsck took 3 seconds. flashfs[1]: Initialization complete. ...done Initializing C3500XL flash. C3500XL POST: System Board Test: Passed C3500XL POST: Daughter Card Test: Passed C3500XL POST: CPU Buffer Test: Passed C3500XL POST: CPU Notify RAM Test: Passed C3500XL POST: CPU Interface Test: Passed C3500XL POST: Testing Switch Core: Passed Error with Switch Core BIST test Phase 0. Returns: Test Complete Low : 0x0FFFFFFF, Test Complete High : 0xFFFFFFFE Test Phase Low : 0x00000040, Test Phase High : 0x00000000 Test Phase Third : 0x00000000, Test Complete Third : 0x000001F8 C3500XL POST FAILURE: Testing Switch Core: Failed C3500XL POST FAILURE: Testing Buffer Table: Failed C3500XL POST FAILURE: Data Buffer Test: Failed C3500XL POST FAILURE: Configuring Switch Parameters: Failed C3500XL POST FAILURE: Switch Core BIST failed. C3500XL POST FAILURE: Cannot test Modules due to failure of Switch Core POST Del Mar Failure (0th Del Mar): req system failed to init C3500XL POST FAILURE: C3500XL POST FAILURE: ATM: required system failed to init C3500XL POST: Ethernet Controller Test: Passed C3500XL POST FAILURE: MII Test: Failed C3500XL POST FAILURE: Error waiting for Ethernet Controller and SW_PARAMS C3500XL POST FAILURE: Initialization/POST failed C3500XL POST FAILURE: AT: Failing because system POST failed Exception (8192)! Debug Exception (Could be NULL pointer dereference) CPU Register Context: Vector = 0x00002000 PC = 0x000F36F4 MSR = 0x00029200 CR = 0x22000024 LR = 0x000F6964 CTR = 0x001DE46C XER = 0x00000000 R0 = 0x00000000 R1 = 0x004E2580 R2 = 0x00000000 R3 = 0x00000000 R4 = 0x00000001 R5 = 0x00000000 R6 = 0x004E2718 R7 = 0x004E2718 R8 = 0x00000008 R9 = 0x00000000 R10 = 0x0000FFFF R11 = 0x00480000 R12 = 0x42000024 R13 = 0x00000000 R14 = 0x00000000 R15 = 0x00000000 R16 = 0x00000000 R17 = 0x00000000 R18 = 0x00000000 R19 = 0x00000000 R20 = 0x00000000 R21 = 0x00000000 R22 = 0x00000000 R23 = 0x00000000 R24 = 0x00000000 R25 = 0x00000020 R26 = 0x004E2718 R27 = 0x004E2718 R28 = 0x00000020 R29 = 0x00002513 R30 = 0x00000001 R31 = 0x00000000 Stack trace: PC = 0x000F36F4, SP = 0x004E2580 Frame 00: SP = 0x004E25A0 PC = 0x40000016 Frame 01: SP = 0x004E2618 PC = 0x000F6964 Frame 02: SP = 0x004E26A8 PC = 0x000F76DC Frame 03: SP = 0x004E26C8 PC = 0x000E8114 Frame 04: SP = 0x004E26F0 PC = 0x001F5BF8 Frame 05: SP = 0x004E2710 PC = 0x001F5CF4 Frame 06: SP = 0x004E2748 PC = 0x0023F4DC Frame 07: SP = 0x004E2750 PC = 0x0023E650 Frame 08: SP = 0x004E27C8 PC = 0x0023E89C Frame 09: SP = 0x004E27E0 PC = 0x0028AF34 Frame 10: SP = 0x004E27E8 PC = 0x001E38F8 Frame 11: SP = 0x004E2808 PC = 0x001E39A8 Frame 12: SP = 0x004E2820 PC = 0x0014E220 Frame 13: SP = 0x004E28C8 PC = 0x0014E39C Frame 14: SP = 0x00000000 PC = 0x001EB510

  Read the article

• Minecraft server Rkit ubuntu upstart [closed]

  - by user1637491

  I have an Intel server running Ubuntu Server 12.04.1 I am working on moving my CraftBukkit Minecraft Server to the new platform. I read the upstart ubuntu cookbook and wrote a .conf file I have a minecraft user (named minecraft) and its home Directory is /home/minecraft it contains prwxrwxrwx 1 minecraft minecraft 0 Sep 19 14:49 command-fifo drwx------ 8 minecraft minecraft 4096 Sep 19 14:50 HDsaves drwx------ 2 minecraft minecraft 4096 Aug 31 15:13 logrolls -rw-r--r-- 1 root root 5 Sep 19 14:49 minecraft.pid drwxrwxrwx 8 minecraft minecraft 180 Sep 19 14:49 ramdisk -rw------- 1 minecraft minecraft 119 Sep 19 10:34 save.sh drwxrwxrwx 9 minecraft minecraft 4096 Sep 19 14:50 server -rw-rw-r-- 1 minecraft minecraft 44 Aug 31 11:40 shutdown.sh the server directory contains drwxrwxrwx 6 minecraft minecraft 4096 Aug 30 13:32 Backups -rwxrwxrwx 1 minecraft minecraft 0 Sep 18 12:26 banned-ips.txt -rwxrwxrwx 1 minecraft minecraft 17 Sep 18 12:26 banned-players.txt drwxrwxrwx 4 minecraft minecraft 4096 Aug 30 12:26 buildcraft -rwxrwxrwx 1 minecraft minecraft 1447 Sep 18 12:26 bukkit.yml -rwxrwxrwx 1 minecraft minecraft 0 Aug 30 11:05 command-fifo drwxrwxrwx 2 minecraft minecraft 4096 Aug 30 12:26 config lrwxrwxrwx 1 minecraft minecraft 23 Sep 19 14:49 craftbukkit.jar -> ramdisk/craftbukkit.jar -rwxrwxrwx 1 minecraft minecraft 17419 Sep 18 12:26 ForgeModLoader-0.log -rwxrwxrwx 1 minecraft minecraft 17420 Sep 18 12:24 ForgeModLoader-1.log -rwxrwxrwx 1 minecraft minecraft 17420 Sep 18 11:53 ForgeModLoader-2.log -rwxrwxrwx 1 minecraft minecraft 2576 Aug 30 11:05 help.yml drwxrwxrwx 2 minecraft minecraft 4096 Aug 30 12:31 lib drwxrwxrwx 3 minecraft minecraft 4096 Sep 19 14:49 logrolls -rwxrwxrwx 1 minecraft minecraft 200035 Sep 4 17:58 Minecraft_RKit.jar lrwxrwxrwx 1 minecraft minecraft 12 Sep 19 14:49 mods -> ramdisk/mods -rwxrwxrwx 1 minecraft minecraft 5 Sep 18 12:26 ops.txt -rwxrwxrwx 1 minecraft minecraft 0 Aug 30 11:05 permissions.yml lrwxrwxrwx 1 minecraft minecraft 15 Sep 19 14:49 plugins -> ramdisk/plugins lrwxrwxrwx 1 minecraft minecraft 16 Sep 19 14:49 redpower -> ramdisk/redpower -rw-r--r-- 1 root root 255 Sep 19 15:10 server.log -rwxrwxrwx 1 minecraft minecraft 464 Sep 8 11:09 server.properties drwxrwxrwx 3 minecraft minecraft 4096 Sep 5 16:05 SpaceModule drwxrwxrwx 3 minecraft minecraft 4096 Aug 30 13:07 toolkit -rwxrwxrwx 1 minecraft minecraft 1433 Sep 14 21:04 wepif.yml -rwxrwxrwx 1 minecraft minecraft 0 Sep 18 12:26 white-list.txt lrwxrwxrwx 1 minecraft minecraft 13 Sep 19 14:49 world -> ramdisk/world lrwxrwxrwx 1 minecraft minecraft 20 Sep 19 14:49 world_nether -> ramdisk/world_nether lrwxrwxrwx 1 minecraft minecraft 21 Sep 19 14:49 world_the_end -> ramdisk/world_the_end the startup .conf file: # Starts the minecraft server after loading JRE from ramdisk # # for now im still working on it description "minecraft-server" start on filesystem or runlevel [2345] stop on runlevel [!2345] oom score -999 kill timeout 60 pre-start script sh /usr/lib/jvm/java.sh end script script cd /home/minecraft echo "$(date) Starting minecraft" sudo cp -r /home/minecraft/HDsaves/* ramdisk sudo chown -R minecraft:minecraft ramdisk sudo chmod -R 777 ramdisk sudo ln -sf ramdisk/* server sudo chown -R minecraft:minecraft server sudo chmod -R 777 server sudo mv server/server.log server/logrolls/ zip server/logrolls/temp.zip server/logrolls/server.log sudo mv server/logrolls/temp.zip server/logrolls/"$(date)".log.zip sudo rm server/logrolls/server.log sudo rm -f command-fifo sudo mkfifo command-fifo sudo chown minecraft:minecraft command-fifo sudo chmod 777 command-fifo echo "$(date) Root commands finished" echo "$(date) Starting Wrapper" cd server sudo -u minecraft java -Xmx30M -Xms30M -XX:MaxPermSize=40M -Djava.awt.headless=true -jar Minecraft_RKit.jar timv:*spoilers* <> /home/minecraft/command-fifo & sudo echo $! >| /home/minecraft/minecraft.pid echo "$(date) Minecraft Started" end script pre-stop script cd /home/minecraft PID=`cat minecraft.pid` if [ "$PID" != "" ]; then echo "Stopping MineCraft Server PID=$PID" sudo echo save-all >> command-fifo sudo echo .stopwrapper >> command-fifo wait $PID sudo rm minecraft.pid sudo rsync -rt --delete ramdisk/* HDsaves/ echo "$(date) ramdisk save complete" echo "MineCraft save-shutdown complete." else echo "MineCraft not running" fi end script so when I start it up the upstart gererated log says: Wed Sep 19 14:49:30 CDT 2012 Starting minecraft adding: server/logrolls/server.log (stored 0%) Wed Sep 19 14:49:56 CDT 2012 Root commands finished Wed Sep 19 14:49:56 CDT 2012 Starting Wrapper Wed Sep 19 14:49:56 CDT 2012 Minecraft Started

  Read the article

• Linux bcm43224 wifi adapter slows down a couple minutes after boot

  - by Blubber

  I just installed Ubuntu on my mid 2012 MacBook Air. Everything worked out of the box, but the wifi is showing some weird behavior. When I first login it's really fast, loading google.com is near instant, and browsing in general feels at least as smooth as it did on Mac OS. However, after a couple minutes the connection slows down dramatically, sometimes it takes over 5s to load google.com, a simple reboot fixes the problem for another couple minutes. Specs: Wifi: 02:00.0 Network controller: Broadcom Corporation BCM43224 802.11a/b/g/n (rev 01) Driver: open-source brcmsmac driver Kernel: Linux wega 3.8.0-21-generic #32-Ubuntu SMP Tue May 14 22:16:46 UTC 2013 x86_64 x86_64 x86_64 GNU/Linux Distro: Ubuntu 13.04 (uptodate) I tried a number of things, none of which actually helped Use proprietary sta driver from broadcom Installed firmware into /lib/firmware/brcms (which, as far as I can tell from logs, does not get loaded at all) Switch router to only use 2.4 OR 5 GHz Set router to only use a OR g OR n Set router to use AES encryption only Turned off power management on the adapter Set regulatory region to the correct value (NL) on both router and laptop Disable ipv6 Nothing seems to help, the slowdown always occurs. I did notice that the latency (ping google.com) stays roughly the same (around 9ms). Below is some more information that might be of use. $ lspci -nnk | grep -iA2 net 02:00.0 Network controller [0280]: Broadcom Corporation BCM43224 802.11a/b/g/n [14e4:4353] (rev 01) Subsystem: Apple Inc. Device [106b:00e9] Kernel driver in use: bcma-pci-bridge $ rfkill list 0: hci0: Bluetooth Soft blocked: no Hard blocked: no 1: phy0: Wireless LAN Soft blocked: no Hard blocked: no $ lsmod Module Size Used by dm_crypt 22820 1 arc4 12615 2 brcmsmac 550698 0 coretemp 13355 0 kvm_intel 132891 0 parport_pc 28152 0 kvm 443165 1 kvm_intel ppdev 17073 0 cordic 12574 1 brcmsmac brcmutil 14755 1 brcmsmac mac80211 606457 1 brcmsmac cfg80211 510937 2 brcmsmac,mac80211 bnep 18036 2 rfcomm 42641 12 joydev 17377 0 applesmc 19353 0 input_polldev 13896 1 applesmc snd_hda_codec_hdmi 36913 1 microcode 22881 0 snd_hda_codec_cirrus 23829 1 nls_iso8859_1 12713 1 uvcvideo 80847 0 btusb 22474 0 snd_hda_intel 39619 3 videobuf2_vmalloc 13056 1 uvcvideo snd_hda_codec 136453 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec_cirrus bcm5974 17347 0 bluetooth 228619 22 bnep,btusb,rfcomm snd_hwdep 13602 1 snd_hda_codec lpc_ich 17061 0 videobuf2_memops 13202 1 videobuf2_vmalloc videobuf2_core 40513 1 uvcvideo videodev 129260 2 uvcvideo,videobuf2_core bcma 41051 1 brcmsmac snd_pcm 97451 3 snd_hda_codec_hdmi,snd_hda_codec,snd_hda_intel snd_page_alloc 18710 2 snd_pcm,snd_hda_intel snd_seq_midi 13324 0 snd_seq_midi_event 14899 1 snd_seq_midi snd_rawmidi 30180 1 snd_seq_midi snd_seq 61554 2 snd_seq_midi_event,snd_seq_midi snd_seq_device 14497 3 snd_seq,snd_rawmidi,snd_seq_midi snd_timer 29425 2 snd_pcm,snd_seq snd 68876 16 snd_hwdep,snd_timer,snd_hda_codec_hdmi,snd_pcm,snd_seq,snd_rawmidi,snd_hda_codec,snd_hda_intel,snd_seq_device,snd_hda_codec_cirrus mei 41158 0 soundcore 12680 1 snd apple_bl 13673 0 mac_hid 13205 0 lp 17759 0 parport 46345 3 lp,ppdev,parport_pc usb_storage 57204 0 hid_apple 13237 0 hid_generic 12540 0 ghash_clmulni_intel 13259 0 aesni_intel 55399 399 aes_x86_64 17255 1 aesni_intel xts 12885 1 aesni_intel lrw 13257 1 aesni_intel gf128mul 14951 2 lrw,xts ablk_helper 13597 1 aesni_intel cryptd 20373 4 ghash_clmulni_intel,aesni_intel,ablk_helper i915 600351 3 ahci 25731 3 libahci 31364 1 ahci video 19390 1 i915 i2c_algo_bit 13413 1 i915 drm_kms_helper 49394 1 i915 usbhid 47074 0 drm 286313 4 i915,drm_kms_helper hid 101002 3 hid_generic,usbhid,hid_apple $ dmesg | egrep 'b43|bcma|brcm|[F]irm' [ 0.055025] [Firmware Bug]: ioapic 2 has no mapping iommu, interrupt remapping will be disabled [ 0.152336] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored [ 2.187681] pci_root PNP0A08:00: [Firmware Info]: MMCONFIG for domain 0000 [bus 00-99] only partially covers this bridge [ 12.553600] bcma-pci-bridge 0000:02:00.0: enabling device (0000 -> 0002) [ 12.553657] bcma: bus0: Found chip with id 0xA8D8, rev 0x01 and package 0x08 [ 12.553688] bcma: bus0: Core 0 found: ChipCommon (manuf 0x4BF, id 0x800, rev 0x22, class 0x0) [ 12.553715] bcma: bus0: Core 1 found: IEEE 802.11 (manuf 0x4BF, id 0x812, rev 0x17, class 0x0) [ 12.553764] bcma: bus0: Core 2 found: PCIe (manuf 0x4BF, id 0x820, rev 0x0F, class 0x0) [ 12.605777] bcma: bus0: Bus registered [ 12.852925] brcmsmac bcma0:0: mfg 4bf core 812 rev 23 class 0 irq 17 [ 13.085176] brcmsmac bcma0:0: brcms_ops_bss_info_changed: qos enabled: false (implement) [ 13.085186] brcmsmac bcma0:0: brcms_ops_config: change power-save mode: false (implement) [ 20.862617] brcmsmac bcma0:0: brcmsmac: brcms_ops_bss_info_changed: associated [ 20.862622] brcmsmac bcma0:0: brcms_ops_bss_info_changed: arp filtering: enabled true, count 0 (implement) [ 20.862625] brcmsmac bcma0:0: brcms_ops_bss_info_changed: qos enabled: true (implement) [ 20.897957] brcmsmac bcma0:0: brcms_ops_bss_info_changed: arp filtering: enabled true, count 1 (implement) $ iwconfig lo no wireless extensions. wlan0 IEEE 802.11abgn ESSID:"wlan" Mode:Managed Frequency:5.22 GHz Access Point: E0:46:9A:4E:63:9A Bit Rate=65 Mb/s Tx-Power=17 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=63/70 Signal level=-47 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:13 Invalid misc:56 Missed beacon:0

  Read the article

• Cannot get official CentOS 5.4 BIND package to start

  - by Brian Cline

  Yesterday I installed CentOS 5.4 on one of my servers, and it appears that the official BIND/named package has trouble starting for reasons I cannot deduce. Here is what happens: [root@hal init.d]# service named start Starting named: Error in named configuration: /etc/named.conf:57: open: named.root.hints: permission denied [FAILED] The line in question, with the directory option for context: // further up in the file: directory "/var/named"; // line 57: include "named.root.hints"; Like you, my first reaction was to check permissions on /var/named/named.root.hints, /var/named, and /var to make sure the named user would be able to read it. Here are the permissions at each level: drwxr-xr-x 19 root root 4096 Nov 3 02:05 var drwxr-x--- 5 root named 4096 Nov 3 02:36 named -rw-r--r-- 1 named named 524 Mar 29 2006 named.root.hints Everything appears to be fine permission-wise. The same error occurs if the /var/named directory is writable by the named user. I've even temporarily allowed the named user to log in via bash, su'ed from root to named, and checked that I was, in fact, able to cat /var/named/named.root.hints successfully. (Yes, don't worry: I changed the shell back to nologin). My last endeavor showed that BIND is able to run under the named user account and start up just fine, if done so manually: [root@hal ~]# named -u named -g 03-Nov-2009 16:31:02.021 starting BIND 9.3.6-P1-RedHat-9.3.6-4.P1.el5 -u named -g 03-Nov-2009 16:31:02.021 adjusted limit on open files from 1024 to 1048576 03-Nov-2009 16:31:02.021 found 2 CPUs, using 2 worker threads 03-Nov-2009 16:31:02.021 using up to 4096 sockets 03-Nov-2009 16:31:02.028 loading configuration from '/etc/named.conf' 03-Nov-2009 16:31:02.030 using default UDP/IPv4 port range: [1024, 65535] 03-Nov-2009 16:31:02.031 using default UDP/IPv6 port range: [1024, 65535] 03-Nov-2009 16:31:02.034 listening on IPv4 interface lo, 127.0.0.1#53 03-Nov-2009 16:31:02.034 listening on IPv4 interface eth0, 10.0.0.5#53 03-Nov-2009 16:31:02.034 listening on IPv4 interface eth1, ww.xx.yy.zz#53 03-Nov-2009 16:31:02.040 command channel listening on 127.0.0.1#953 03-Nov-2009 16:31:02.040 command channel listening on ::1#953 03-Nov-2009 16:31:02.040 ignoring config file logging statement due to -g option 03-Nov-2009 16:31:02.041 zone 0.in-addr.arpa/IN/localhost_resolver: loaded serial 42 03-Nov-2009 16:31:02.042 zone 0.0.127.in-addr.arpa/IN/localhost_resolver: loaded serial 1997022700 03-Nov-2009 16:31:02.042 zone 255.in-addr.arpa/IN/localhost_resolver: loaded serial 42 03-Nov-2009 16:31:02.042 zone 0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.ip6.arpa/IN/localhost_resolver: loaded serial 1997022700 03-Nov-2009 16:31:02.043 zone localdomain/IN/localhost_resolver: loaded serial 42 03-Nov-2009 16:31:02.043 zone localhost/IN/localhost_resolver: loaded serial 42 03-Nov-2009 16:31:02.043 zone x.y.z.in-addr.arpa/IN/internal: loaded serial 1 03-Nov-2009 16:31:02.044 zone x.y.z/IN/internal: loaded serial 2 03-Nov-2009 16:31:02.045 running What type and size of firearm should I use to resolve this? I'd prefer something with automatic ammunition, and, at worst, it should be able to fit on my shoulder. Of course I am open to suggestions.

  Read the article

• htaccess on remote server issues - password prompt not accepting input

  - by pying saucepan

  EDIT: I will contact the university about my problem after labor day weekend, but I thought if someone knew a quick fix that I haven't tried, or if the problem has an obvious fix then I could hope to try my luck here, thanks! TLDR: Sorry its a long post, I thought I should be... thorough. I am having a common issue (found a dead thread through google with no solution to the same problem) with the prompt to enter in a username and password via htaccess rights, but this prompt will keep popping up asking for a username and password when trying to access my home directory on my university's server which has the .htaccess and .htpasswd files. It does not matter if I enter in correct or incorrect credentials, the prompt will keep asking me for input without displaying my home directory. Ever since I have included these ht files I have never once been able to get past the username/password no matter what I have tried, save for removing them from the directory I am trying to access (my top level directory that I own). This kind of served my original goal of making the top level directory inaccessible to casual users, but if I wanted to use this method on other places, I would want it to work as intended. And I also like it when computers do what I wish they would, so any help is appreciated. Some things I have tried: Changing the file/directory access rights: they told me to try these commands if people can't access my files cd ~/public_html find ./ -type d -exec chmod 755 {} \; find ./ -type f -exec chmod 644 {} \; enter in the single character name/pw at least twenty times in a row, no cheddar. so I changed directory with cd ~ in hopes that this would be my home directory, since my home directory contains the "public_html" directory, so logic tells me that the ~ tilde symbol is the top level directory that I have ownership of. Then I did those two commands to change the rights on the files inside, I am still having no luck. How I got to this point: I have been following the instructions given to me through my university's website for setting up my little directory. A link on how they describe how to password protect the home directory is given below: "Protect Web Directories" instructions I have everything in order except for one small detail that I feel probably does not matter. I am on windows and so I am using winSCP to remote control my allocated server space. The small detail is that as the instructions indicate (on step 3) that I should use the command htpasswd -c .htpasswd {username} where {username} is my folder that holds my allocated server space. But this command requires further input through the terminal, and unfortunately winSCP does not offer this kind of functionality. So I looked up some basic instructions on using htaccess and it is formatted correctly such that the .htaccess file appears as follows: AuthType Basic AuthName "Verify" AuthUserFile /correctpath/.htpasswd require valid-user and this file is in the root directory for my server space as well as the .htpasswd file which has only this data inside: username:password I know for sure that these two files must be formatted correctly, at least according to their tutorial, because before my path was incorrectly formatted via including some curly { braces } without knowing the correct way to do this at first. And the password prompt that shows up when accessing my directory responded by loading an error page indicating to contact OSU admin or something not important. But now that I have everything like it 'should' be. I know this because when I enter in my credentials "username and password" the prompt pops up for my username and password again and again whether or not I enter in correct information. The only exception is that if I click cancel it will direct me to a page saying that I need to enter in a username and password. Note that I am very inexperienced at server-related buisness, two days ago I couldn't have told you what a website actually consists of. So, if you use some technical jargon I may or may not need to look it up and get back to you before I actually understand what you mean, but I am a quick learner and it probably wont matter.

  Read the article

• FreeBSD with Vagrant - don't know how to check guest additions version

  - by joelmaranhao

  On Mac OS X 10.9.3 Picked a box from the VagrantCloud Init the vagrant box $ vagrant init chef/freebsd-9.2-i386 A `Vagrantfile` has been placed in this directory. You are now ready to `vagrant up` your first virtual environment! Please read the comments in the Vagrantfile as well as documentation on `vagrantup.com` for more information on using Vagrant. List the files $ ls -al -rw-r--r-- 1 joel staff 4831 Jun 5 17:17 Vagrantfile Vagrantfile content VAGRANTFILE_API_VERSION = "2" Vagrant.configure(VAGRANTFILE_API_VERSION) do |config| config.vm.box = "chef/freebsd-9.2-i386" end Starting my virtual box leads to Errors $ vagrant up Bringing machine 'default' up with 'virtualbox' provider... ==> default: Box 'chef/freebsd-9.2-i386' could not be found. Attempting to find and install... default: Box Provider: virtualbox default: Box Version: >= 0 ==> default: Loading metadata for box 'chef/freebsd-9.2-i386' default: URL: https://vagrantcloud.com/chef/freebsd-9.2-i386 ==> default: Adding box 'chef/freebsd-9.2-i386' (v1.0.0) for provider: virtualbox default: Downloading: https://vagrantcloud.com/chef/freebsd-9.2-i386/version/1/provider/virtualbox.box ==> default: Successfully added box 'chef/freebsd-9.2-i386' (v1.0.0) for 'virtualbox'! ==> default: Importing base box 'chef/freebsd-9.2-i386'... ==> default: Matching MAC address for NAT networking... ==> default: Checking if box 'chef/freebsd-9.2-i386' is up to date... ==> default: Setting the name of the VM: freebsd92-i386_default_1401982167145_49633 ==> default: Fixed port collision for 22 => 2222. Now on port 2201. ==> default: Clearing any previously set network interfaces... ==> default: Preparing network interfaces based on configuration... default: Adapter 1: nat ==> default: Forwarding ports... default: 22 => 2201 (adapter 1) ==> default: Booting VM... ==> default: Waiting for machine to boot. This may take a few minutes... default: SSH address: 127.0.0.1:2201 default: SSH username: vagrant default: SSH auth method: private key default: Warning: Connection timeout. Retrying... default: Warning: Connection timeout. Retrying... ==> default: Machine booted and ready! Sorry, don't know how to check guest version of Virtualbox Guest Additions on this platform. Stopping installation. ==> default: Checking for guest additions in VM... default: The guest additions on this VM do not match the installed version of default: VirtualBox! In most cases this is fine, but in rare cases it can default: prevent things such as shared folders from working properly. If you see default: shared folder errors, please make sure the guest additions within the default: virtual machine match the version of VirtualBox you have installed on default: your host and reload your VM. default: default: Guest Additions Version: 4.2.16 default: VirtualBox Version: 4.3 ==> default: Mounting shared folders... default: /vagrant => /Users/joel/Code/anybots/operations/robot/freebsd92-i386 Vagrant attempted to execute the capability 'mount_virtualbox_shared_folder' on the detect guest OS 'freebsd', but the guest doesn't support that capability. This capability is required for your configuration of Vagrant. Please either reconfigure Vagrant to avoid this capability or fix the issue by creating the capability. Note that I have recently installed the latest version of VirtualBox, but somehow I can't find the Guest Additions.

  Read the article

< Previous Page | 245 246 247 248 249 250 251 252 253 254 255 256  | Next Page >