Search Results

Search found 9011 results on 361 pages for 'common'.

Page 250/361 | < Previous Page | 246 247 248 249 250 251 252 253 254 255 256 257  | Next Page >

  • Is "DSLAM congestion" a legitimate reason for slow DSL?

    - by Jay Bazuzi
    My DSL has been extremely slow in the evenings recently. To test it, I telnet to my DSL Modem, and ping the gateway. This way I eliminate internet congestion and local network issues. In the mornings I get 30ms - 50ms pings. In the evenings, it bounces around a lot, but 10000ms pings are common. I complained to Qwest support, and they said it was a known issue on their end, their engineers were working on it, and wouldn't say anything else. A couple days later I complained again, and they sent out a technician. He tested my house wiring and found that one of them had a short. It was an unused line, so we disconnected it, and he said things looked better and left. My daytime speeds improved at this point, but evening is still bad. I complained to Qwest support again, and they said it was a problem with DSLAM congestion at their end, and that they were working on it, but no ETA. My neighbor has Qwest DSL and doesn't seem to have these problems. That seems strange. I go use her network when I absolutely must get online and mine is behaving badly. I can't tell if they're yanking my chain or not. Regardless, these speeds are crap. I'm paying for 7Mpbs but am lucky if I get 1/10th that in the evenings. My kids like to watch Netflix streaming movies, and it's just impossible after 5pm or so. Should I wait it out? Will complaining again produce any results? Should I change my subscription to a lower speed until they fix their end? Or switch to cable?

    Read the article

  • ssh key questions

    - by Tim
    I have some questions regarding generating keys for ssh access: (1) Supposed there are two computers running ssh server service and I have generated a pair of key files on computer A and copy the public file to computer B. Is it true that this is only a one-way key: We only gave computer A permission to access computer B, not gave computer B permission to access computer A? If I now want to ssh from computer B to computer A, must I generat another pair of key files on computer B and copy the public file to computer A? (2) If I would like to connect a single local computer to several remote servers, is it to generate a common pair of key files only once on the local and copy the same public file to the remote servers, or to generate different pair of key files on the local for different remote servers? (3) If I would like to connect several local computers to a single remote server, when copying the public files from different local computers to the remote server, is it to combine them together into a single authorized_keys file or store them in different authorized_keys files? (4) If there are several servers shared the same file system by, for example, NFS, how to generate keys and arrange the key files for accessing from one server to the other? Also how to still generate keys and arrange the key files for a local computer to access anyone of the servers? All the machines above are Linux.Please provide examples and commands in your reply so that I can better understand how to solve the problems. Thanks and regards!

    Read the article

  • Is it possible to detect nearby Wi-Fi enabled devices, not necessarily on the same network? [closed]

    - by Sky
    first question on StackExchange ever. I hope I got the right board. I'm trying to create a device (either from a standard AP or some other unconventional means) that will be able to detect nearby Wi-Fi enabled devices. For example, if a cellular phone (iPhone for instance) would be carried into the secured area, its MAC address will be logged. A cellular phone is a good example because it's the most common threat that should be detected. Some important points: The detection can be either active or passive, doesn't matter. The detected device might be connected to a different network, or might not be connected to anything at all. I assume most cellular phones are actively probing when not connected, but I'm not sure. It is important to not only identify the breach, but also to identify the device (MAC address). Conventional hardware is only optional. Distance of detection is at least 6 meters (20 feet). Handling one device at a time is good. Speed of detection is important, under 5 seconds is ideal. So my question is, is this even possible? If so, what can I use in order to make this a reality? Thank you for reading!

    Read the article

  • TFS 2012 and MS SQL 2008r2

    - by Vadim911
    When I try to call TFS 2012 warehouse control web service (WarehouseControlService.asmx) I got following error: Exception Message: Could not load file or assembly 'Microsoft.AnalysisServices, Version=10.0.0.0, Culture=neutral, PublicKeyToken=89845dcd8080cc91' or one of its dependencies. The system cannot find the file specified. (type FileNotFoundException) Exception Stack Trace:    at Microsoft.TeamFoundation.Warehouse.WarehouseConfigurationService.RebuildOLAPDatabase(TeamFoundationRequestContext requestContext, String olapServerInstanceName, String databaseName, String warehouseServerInstanceName, String warehouseDatabaseName, Int32 translationLCID, Boolean checkAndUpdateJobs)    at Microsoft.TeamFoundation.Warehouse.WarehouseConfigurationService.RebuildOLAPDatabase(TeamFoundationRequestContext requestContext, String olapServerInstanceName, String databaseName, String warehouseServerInstanceName, String warehouseDatabaseName, Int32 translationLCID)    at Microsoft.TeamFoundation.Management.SnapIn.ApplicationTierNode.RebuildReporting(IntPtr hwnd, IRefreshable panel) Inner Exception Details: Exception Message: Could not load file or assembly 'Microsoft.AnalysisServices, Version=11.0.0.0, Culture=neutral, PublicKeyToken=89845dcd8080cc91' or one of its dependencies. The system cannot find the file specified. (type FileNotFoundException) Exception Stack Trace:    at System.Reflection.RuntimeAssembly._nLoad(AssemblyName fileName, String codeBase, Evidence assemblySecurity, RuntimeAssembly locationHint, StackCrawlMark& stackMark, IntPtr pPrivHostBinder, Boolean throwOnFileNotFound, Boolean forIntrospection, Boolean suppressSecurityChecks)    at System.Reflection.RuntimeAssembly.InternalLoadAssemblyName(AssemblyName assemblyRef, Evidence assemblySecurity, RuntimeAssembly reqAssembly, StackCrawlMark& stackMark, IntPtr pPrivHostBinder, Boolean throwOnFileNotFound, Boolean forIntrospection, Boolean suppressSecurityChecks)    at System.Reflection.Assembly.Load(AssemblyName assemblyRef)    at Microsoft.TeamFoundation.Common.Internal.TfsAssemblyResolver.OnAssemblyResolve(Object sender, ResolveEventArgs args)    at System.AppDomain.OnAssemblyResolveEvent(RuntimeAssembly assembly, String assemblyFullName) It is strange because I have installed ms sql connectivity. Is it issue connected with the fact that I try to use tfs 2012 with ms sql 2012? Please advise how to resolve issue networked above.

    Read the article

  • duplicity fail: not promping for password: "Running 'sftp user@host' failed"

    - by Thr4wn
    I have two linode VPS accounts and I want to back up one onto the other (the reasons are mainly for fun and to practice server administration.) the short version Duplicity isn't even asking for my password, but immediately says "invalid SSH password" (but I can ssh into the other server). why? the long version When I run duplicity /home/me scp://[email protected]//root/backup I get Invalid SSH password Running 'sftp [email protected]' failed (attempt #1) Invalid SSH password Running 'sftp [email protected]' failed (attempt #2) Invalid SSH password Running 'sftp [email protected]' failed (attempt #3) And it says Invalid SSH password immediately with no opportunity for me to actually type the password. When I type duplicity full -v9 --num-retries 4 /home/me scp://[email protected]//root/backup I get Main action: full Running 'sftp [email protected]' (attempt #1) State = sftp, Before = 'Connecting to 97.107.129.67... [email protected]'s' State = sftp, Before = '' Invalid SSH password Running 'sftp [email protected]' failed (attempt #1) I can ssh into [email protected] fine, and in fact have the ip in known_hosts before I tried any of this. serer 1 (from which I'm running the duplicity command) is Linode's default Ubuntu 8 setup with only a handful of programs installed via apt-get. server 2 (represented by x.x.x.x) is literally only Linode's default Ubuntu 8 setup I previously tried using SystemImager -- would that have changed settings in a destructive way? (I have removed and rebooted since then) Isn't Duplicity supposed to prompt for password? Am I using it wrong? are there common mistakes/dependencies I need to know about? Is there any way that x.x.x.x could be setup that could make this not work (I used Linode's default Ubuntu 8 setup and barely )?

    Read the article

  • Working with barcode fonts in Word

    - by Bob Rivers
    I need to create labels in Microsoft Word 2010 with numbers encoded as barcodes. The barcode's format (ean, code39, upc, etc) does not matter. I have downloaded a barcode conversion font that I found at this site. When I type the number that I want and then I format it with my new font, it produces a barcode. I then print it on an OKI laser printer (1200 dpi). The result seems to be fine, at least for common people. But, when I try to scan it, nothing happens. I tried both with a barcode scanner and a data collector, but neither of them read the barcode. My barcode scanner is working fine, because I can read commercial barcodes printed on products. Does anybody have any advice? How do I do this kind of stuff? I want to do it using Word because I will generate labels using Mail Merge. Therefore using external programs aren't option for me.

    Read the article

  • Re-configure Office 2007 installation unattended: Advertised components --> Local

    - by abstrask
    On our Citrix farm, I just found out that some sub-components are "Installed on 1st Use" (Advertised), which does play well on terminal servers. Not only that, but you also get a rather non-descriptive error message, when a document tried to use a component, which is "Installed on 1st Use" (described on Plan to deploy Office 2010 in a Remote Desktop Services environment): Microsoft Office cannot run this add-in. An error occurred and this feature is no longer functioning correctly. Please contact your system administrator. I have ~50 Citrix servers where I need to change the installation state of all Advertised components to Local, so I created an XML file like this: <?xml version="1.0" encoding="utf-8"?> <Configuration Product="ProPlus"> <Display Level="none" CompletionNotice="no" SuppressModal="yes" AcceptEula="yes" /> <Logging Type="standard" Path="C:\InstallLogs" Template="MS Office 2007 Install on 1st Use(*).log" /> <Option Id="AccessWizards" State="Local" /> <Option Id="DeveloperWizards" State="Local" /> <Setting Id="Reboot" Value="NEVER" /> </Configuration> I run it with a command like this (using the appropriate paths): "[..]\setup.exe" /config ProPlus /config "[..]\Install1stUse-to-Forced.xml" According to the log file, the syntax appears to be accepted and the config file parsed: Parsing command line. Config XML file specified: [..]\Install1stUse-to-Forced.xml Modify requested for product: PROPLUS Parsing config.xml at: [..]\Install1stUse-to-Forced.xml Preferred product specified in config.xml to be: PROPLUS But the "Final Option Tree" still reads: Final Option Tree: AlwaysInstalled:local Gimme_OnDemandData:local ProductFiles:local VSCommonPIAHidden:local dummy_MSCOMCTL_PIA:local dummy_Office_PIA:local ACCESSFiles:local ... AccessWizards:advertised DeveloperWizards:advertised ... And the components remain "Advertised". Just to see if the installation state is overridden in another XML file, I ran: findstr /l /s /i "AccessWizards" *.xml Against both my installation source and "%ProgramFiles%\Common Files\Microsoft Shared\OFFICE12\Office Setup Controller", but just found DefaultState to be "Local". What am I doing wrong? Thanks!

    Read the article

  • Apache, suexec, PHP, suPHP

    - by Chris_K
    While I'm quite comfortable as a Linux user, my Linux Admin-fu is a bit weak. Thus, I'm here looking for guidance with a CentOS server I'm about to build. I need to setup an Apache2 web server for a few of our clients. I want each client's web content to be under their home directory (USERDIR in apache.conf, right?) for the static HTML sites. I want Apache to run as the client (suexec?). Some of their stuff will be PHP apps and I'm under the impression I'll want to look at suphp as well then. So basically I want to look like a small version of a shared web hosting company. Considering how common those are I thought I'd easily find a nice current How-To guide on setting this all up but so far I've had very little luck. I suspect my search words are off. So the questions (feel free to answer any or all): Anyone have some solid links to current/modern guides that would help me set this all up? No, the apache documentation site is not a guide ;-) Since I have a mix of static sites and PHP apps do I want/need both suexec and suphp installed? If so, does that introduce any challenges I should be aware of? Should I be looking at other options instead of suexec and suphp? I plan to give the end users SSH, SFTP or SCP access to their stuff (if that affects anything). Thanks in advance for your help.

    Read the article

  • What is the collaborative screen shot/diagramming application recently featured on Hacker News and p

    - by wonsungi
    A few days ago, I saw this video for a screen capture application. I'm pretty sure I followed a link from Hacker News, possibly to a Life Hacker article. The video was very short, but demonstrated how the application could be used: The application was basically a movable/resize-able view port with a button. When the button is pressed, the contents of the view port are saved to an image (basically a screen capture.) The interesting thing is what you could do after that point. One of the specific examples from the video browsed to Google maps street view, grabbed a photo of an intersection, then scribbled notes about where to meet and where the restaurant was in colored "marker." Another example shown was grabbing a house layout from from CAD tool, then scribbling notes on it. The last part of the video showed several possible uses being scrolled through the application's view port. Now, it seemed it was very easy to share these images with other people because there was some type of integration, either with their own site and/or common social websites/chat services. The application was shown running on both Windows and Mac. edit: I think there was an iPhone app, as well. Anyone know what this application is? I tried searching Google, Hacker News, and Life Hacker already. It is not Jing.

    Read the article

  • Ubuntu 10.04 server delay responding to AJAX requests

    - by DanielAttard
    I manage a Ubuntu 10.04 server with a couple of domains hosted on it. As I continue to learn more about all these wonderful new (for me), one issue that I have begun to notice is the delay it sometimes takes for the server to respond to certain requests. As an example, when I view the timeline of events using firebug I can see that most of the time when I make a POST, the server responds in under 100ms. Sometimes, however, there is a substantial delay before the RESPONSE from the server. I can't seem to tell when the delay will happen and when it won't, however, when it happens the delay is always for about 4.5 seconds. The delay seems to happen about 30-40% of the time. Here is the section of apache2.conf dealing with logs: # # The following directives define some format nicknames for use with # a CustomLog directive (see below). # If you are behind a reverse proxy, you might want to change %h into %{X-Forwarded-For}i # LogFormat "%v:%p %h %l %u %t \"%r\" %>s %O \"%{Referer}i\" \"%{User-Agent}i\"" vhost_combined LogFormat "%h %l %u %t \"%r\" %>s %O \"%{Referer}i\" \"%{User-Agent}i\"" combined LogFormat "%h %l %u %t \"%r\" %>s %O" common LogFormat "%{Referer}i -> %U" referer LogFormat "%{User-agent}i" agent I have no idea where to look to try and debug this problem or investigate further. Any suggestions?

    Read the article

  • Default Gateway solution on NAT'd network (best options)

    - by kwiksand
    I've recently changed a network from a bunch of machines exposed to the net on a network to a more security conscious Firewall-fronted network with a DMZ for public services. Everything's mostly working perfectly now, but I've got the old problem of NAT Loopback where a machine within the LAN wants to access a public service via the public/external IP. I've solved this problem previously in a small/SOHO environment simply using NAT loopback features of the router in use or a simple iptables rule to do the same, but I want to make sure I make the most resilient choice with the least concern. It seems I can: Use iptables as I've said to DNAT and MASQUERADE the change source/destination so the connection works correctly i.e iptables -A PREROUTING -t nat -d ip.of.eth0.here -p tcp --dport 8080 -j DNAT --to 192.168.0.201:8080 iptables -t nat -A POSTROUTING -s 192.168.0.0/24 -p tcp --dport 8080 -d 192.168.0.201 -j MASQUERADE Use split DNS, with internal mappings for public IP's Potentially do some route nastyness by setting the Default Gateway to use a different externally exposed IP to then come back in the public route (messy) Someone mentioned putting the Default Gateway within the DMZ as well (on serverfault), but I can't find the post again. I'm sure this is a common issue for many with NAT'd networks, but I've not really seen the perfect solve all when it comes to fixing this problem. What is your opinion?

    Read the article

  • What are some alternatives to word processing with Markdown?

    - by Hassan
    I've used MS Word-style editors for a long time, but I never got used to how unintuitive and cumbersome they are. I'm not talking specifically about MS Word, but also other editors that seem to mimic Word, like OpenOffice, NeoOffice, etc. I've found myself preferring to write in Markdown (much like on this site). I've found a few good Markdown editors, and I like using them a lot more than using Word-style editors. Here is what they generally look like: As you can see, it works much differently than a Word-style editor. This is a generally cleaner way of writing, since formatting is done right in the text, and is extremely simple to use (no highlighting some text, then clicking a button in some menu you have to find). Although editing text this way is great, I've realized that the syntax can only be used for very specific needs (bullets, numbered lists, headings and sub-headings, bold, italic, and some other common ones). However, many features are missing. Here are some features that would be nice in a word processor: Tables. Indenting paragraphs. Good image support (you can link to images, but not add them, since Markdown is just text). More simple to use than Word and its cronies. Cross-platform. Some of these can be fixed with in-line HTML, but nobody wants to do that. It seems Markdown was designed for editing text on the internet. Is there a similar setup that works better for desktop word processors?

    Read the article

  • How can I enable PHP5 for a site? Having problems with every single method.

    - by John Stephens
    I'm working on a client site that is hosted on someone's DIY Debian Linux server [Apache/1.3.33 (Debian GNU/Linux)], and I'm trying to install a script that requires PHP5. By default, the server parses .php files with PHP 4.3.10-22, which is configured at /etc/php4/apache/php.ini, according to phpinfo(). On the server I can see a config directory for PHP5 adjacent to the PHP4 directory: /etc/php5.0/apache2/php.ini. I have tried multiple methods to enable PHP5 for the document root where the site's files are hosted, including all available methods mentioned here. By far, the most common suggestion I've found is to add one or both of the following lines to the site's .htaccess file: AddHandler application/x-httpd-php5 .php AddType application/x-httpd-php5 .php Trouble is, when either or both of those lines are present, the site forces my browser to download any .php files requested, without parsing the PHP at all. All of the other methods mentioned in the above article cause a 500 Internal Server Error. There is no hosting control panel I can access in a browser to enable PHP5 for the site, but I do have shell access. When I asked the server administrator about this issue, he encouraged me to search for the answer on Google. Where could I begin to troubleshoot this issue? Are there ways to test or verify the server's specific PHP5 installation and configuration, using the command line or some other method? Do you have other suggestions to enable PHP5?

    Read the article

  • Symantec Endpoint Protection Virus Definitions

    - by Gus Denton
    I have done some Googling but I cannot get a definitive answer certainly not from the Symantec KB. I have a Virtualised Win 2003R2 server 32bit. It has been provisioned to me with Symantec Endpoint Protection 11.0.62xxx CLIENT (not a definitions server) the directory C:\Program Files\Common Files\Symantec Shared\VirusDefs is 750MB IT doesn't contain .tmp directories so it is NOT a corrupt definitions server. IT does contain directories named with a date pattern YYYYMMDD.xxx Some of these folders are 12 months old and I would like to recover the space. The sysmantect forums are full of this stuff but a lot of the postings contain links back to documents that are not specific to End Point Protection Client. It appears that I should be able to delete the older folders and all will be OK. with a service restart however there is a warning about having Live Update Administrator Installed Firstly I have no idea if I have this installed how to I check and secondly can I just ditch these old files and restart ? Regards Gus Denton Learning and Teaching Uni of New South Wales Sydney Australia For those trying to assist me I thankyou. I have followed some instructions found on the Symantec site and assumed that the response from Nixphoe would resolve my issue. It appears that as I am on a provisioned VM from a central IT unit I cannot run the Symantec commands from the Run prompt as my admin creds to get me in. (smc -stop) Basically I need to claw back some Diskspace from the c: drive which is being filed up with WSUS patches and Symantec files. I have managed to delete one symantec cache through the live update control panel and recovered 470Mb I suppose my last question for those more experienced than myself is, can I simply remove say the two oldest virus definition folders without completely foobaring the End Point protection and the server ? Regards Gus

    Read the article

  • Apache logging issues

    - by Dan
    I'm trying to parse apache log files, but I'm finding some strange results and I'm not sure what they mean. Hopefully someone can provide some insight. (all of the IP addresses were altered. none actually start with 192, I didn't figure the search engines mattered though.) In the first example, multiple ip addresses are showing up in the host field: 192.249.71.25 - - [04/Aug/2009:04:21:44 -0500] "GET /publications/example.pdf HTTP/1.1" 200 2738 192.0.100.93, 192.20.31.86 - - [04/Aug/2009:04:21:22 -0500] "GET /docs/another.pdf HTTP/1.0" 206 371469 What causes this? Does it have to do with proxy servers? Is there a way to have Apache only log one? In the second example, a bunch of information is just completely missing! What would cause this? msnbot-65-55-207-50.search.msn.com - - [29/Dec/2009:15:45:16 -0600] "GET /publications/example.pdf HTTP/1.1" 200 3470073 "-" "msnbot/2.0b (+http://search.msn.com/msnbot.htm)" 266 3476792 - - - - "-" - - "-" "Mozilla/4.0 (compatible; MSIE 8.0; Windows NT 5.1; Trident/4.0; InfoPath.1)" 285 594 - - - - "-" - - "-" "Mozilla/4.0 (compatible; MSIE 8.0; Windows NT 5.1; Trident/4.0; InfoPath.1)" 285 4195 - - - - "-" - - "-" "Mozilla/4.0 (compatible; MSIE 8.0; Windows NT 5.1; Trident/4.0; InfoPath.1)" 299 109218 crawl-17c.cuil.com - - [29/Dec/2009:15:45:46 -0600] "GET /publications/another.pdf HTTP/1.0" 200 101481 "-" "Mozilla/5.0 (Twiceler-0.9 http://www.cuil.com/twiceler/robot.html)" 253 101704 My CustomLog configuration says: LogFormat "%h %l %u %t \"%r\" %s %b \"%{Referer}i\" \"%{User-agent}i\" %I %O" common

    Read the article

  • Adding 2008 Server to 2008 Domain

    - by Phillip
    Hello, I'm trying to create a lab for testing before I deploy solutions, I'm no experienced IT Administrator, and therefore I come here for help. I'm running 2 Virtual Servers on the same machine on a local connection between those two. They'are able to ping each other. Their names is TSDATA1 and TSDATA2 where TSDATA1 is the Domain Controller. I am able to ping between those two, on both "ping TSDATA1" and "ping 10.0.0.1" which is the IP address of TSDATA1. The IP address of TSDATA2 is 10.0.0.2. I'm trying to join the domain with TSDATA2 both I'm getting this error when trying: Note: This information is intended for a network administrator. If you are not your network's administrator, notify the administrator that you received this information, which has been recorded in the file C:\Windows\debug\dcdiag.txt. The following error occurred when DNS was queried for the service location (SRV) resource record used to locate an Active Directory Domain Controller for domain tsdata.local: The error was: "DNS name does not exist." (error code 0x0000232B RCODE_NAME_ERROR) The query was for the SRV record for _ldap._tcp.dc._msdcs.tsdata.local Common causes of this error include the following: The DNS SRV records required to locate a AD DC for the domain are not registered in DNS. These records are registered with a DNS server automatically when a AD DC is added to a domain. They are updated by the AD DC at set intervals. This computer is configured to use DNS servers with the following IP addresses: 10.0.0.1 One or more of the following zones do not include delegation to its child zone: tsdata.local local . (the root zone) For information about correcting this problem, click Help. I've figured out it has something to do with DNS lookup, but I have no clue what to do. Can anyone help?

    Read the article

  • Cisco VPN endpoints disconnecting from a VLAN

    - by dunxd
    I have a number of Cisco ASA 5505 and PIX 506e around the world acting as VPN endpoints. They connect to a Cisco VPN Concentrator 3000 at HQ. I am using EZVPN to set up the VPN (i.e. most of the config is central on the VPN Concentrator) The majority of endpoints work absolutely fine. However, there are three that do not. 2 ASAs and 1 PIX get disconnected from one of the VLANs on our network. This is the VLAN that my monitoring server runs on - so those endpoints look as if they have gone down. However, I can still ping the endpoints from our user VLAN. If I then SSH onto the endpoint, and do a ping to my monitoring server, the connection comes back. Then after about 10 minutes it stops working again. I've looked at the configuration of my endpoints, and I can't see any significant differences. One common feature is that the affected endpoints are connecting to the internet via retail quality routers. However, I don't see how this could affect traffic within a VPN tunnel. Any ideas or suggestions? I've also got a thread on Cisco's forums at https://supportforums.cisco.com/thread/344638. One other person has reported the same problem.

    Read the article

  • Portable, battery-powered, wireless access point, ethernet adapter

    - by Jed
    I am in need of an adapter that will convert an ethernet port into a wireless access point. I have found a handful of devices, but I'm unable to find a device that is battery powered. Does a self-powered wireless access point even exist? The particular scenario that I will be using the device for is not your typical computer/PC scenario. For the curious, here's a bit of background on the problem I'm trying to solve: I make devices (controllers) that monitor water systems. Our controllers have a Webserver that serves out web pages so that users can configure the controller's settings. Typically, the user will use a cross-over cable to connect directly to the controller's ethernet port with their laptop to gain access to the controller's web pages. Now that tablets (devices that don't have an ethernet port - iPad, for example) are becoming more common, I need to find a device that will convert the controller's ethernet port into a wireless access point so that the user can connect to the controller's web pages via Wi-Fi or Bluetooth. It's worth noting that this wireless device that I'm looking for will NOT be permanently installed on the controller. It will be a portable device that the user will use on any of his controllers when he needs to make a connection to the controller. If you know of a device that will solve the scenario that I mention above, please share your info.

    Read the article

  • Can't resolve offline file conflicts

    - by Bryan
    We use roaming profiles on our Server 2008 R2 domain, with folder redirection for 'desktop', 'my documents' and 'application data'. But as our network is split across two sites, we have one file server at each site, which are configured to use domain based DFS namespaces and DFS replication to keep things in sync. The DFS path for the replication folder is as follows: \\domain\folderredirection$\<username>\<redirected-folder-name> The real paths are \\site-1-server\folderredirection$\<username>\<redirected-folder-name> and \\site-2-server\folderredirection$\<username>\<redirected-folder-name> As our users all switch between sites (sometimes several time per day), our folder redirection policy has to redirect to the DFS roots rather than hardcoded to a specific server. Both DFS and DFS-R have been proven to be working perfectly. On our laptops, we use offline files for the redirected folders, and this also works fine, however the problem is as follows: When conflicts occur in offline files, it is impossible to resolve the conflicts. I'm given the usual conflict resolution options (i.e. 'Ignore', 'Keep Both', 'Keep network' and 'Keep local'), however, not one of these options will resolve any conflict, yet no error is produced. We only use offline files on laptops, which have either Windows XP Professional or Windows 7 Professional installed. The problem is not specific to any one laptop, it affects every laptop and every conflicting file in exactly the same way. I would have thought the set up we have is common for companies that have multiple sites, so I'm hoping someone will have seen this before?

    Read the article

  • How to migrate a running KVM (with full disk copy) to another node?

    - by klipz
    I'm doing tests on KVM, and I'd like to see if I can make a hot migration, I mean the virtual machine won't stop running during the migration (but a few seconds of freeze is ok). I use a small cluster for my test : kvm1, kvm2, and kvmnfs. kvm1 and kvm2 runs the virtual machines kvmnfs is a NFS server, and it's mounted on /KVM on both kvm1 and kvm2 To migrate a VM (only RAM in fact) from kvm1 to kvm2, I run the same kvm command on kvm2 (with -incoming tcp:0:4444) that on kvm1, then I use "migrate -d tcp:kvm2:4444" : It works great, since the VM file is common to both machines. Now, I wan't to make a full migration (RAM + disk) of a local VM file (no more NFS) of kvm1 to kvm2. I tried to create an empty file, with touch, on kvm2 and use the same kvm command line + the "-incoming ..."). Then on kvm1 I use "migrate -d tcp:kvm2:4444" : It copies everything, then... the VM fails (any I/O disk gives an I/O error) ! And my VM file on kvm2, the one I created with touch, as still a size of 0 bytes. What am I doing wrong ? What is the exact command to use on kvm2 ? And what is the command to launch, in the monitoring mode, on kvm1 ?

    Read the article

  • Process files in a folder that haven't previously been processed

    - by Paul
    I have a series of files in a directory that I need to carry an action out on using a script. Once the action is done, then I want to keep a log that the file has been processed, so that the next time the script is run, it does not attempt to carry out the action again. So lets say I can find all the files that should be processed like this: for i in `find /logfolder -name '20*.log'` ; do process_log $i echo $i >> processedlogsfile done So I have a file containing the logs I have processed, and my goal would be to modify the for loop such that these processed logs are not processed a second time. Doing a manual scan each time seems inefficient, particularly as the processedlogfiles gets bigger: if grep -iq "$i" processdlogfiles ; then continue; fi It would be good if these files could be excluded when setting up the for loop. Note that the OS in question is a linux derivative, a managment appliance, with a limited toolset (no attr command for example) and so no way to install additional utilities (well it is possible but not an option). Most common bash shell commands are available though. Also, the filenames and locations of the processed files must remain where they are - they can't be altered to reflect their processed status

    Read the article

  • OpenVPN connected but not internet access on the client

    - by Stefan
    I've setup OpenVPN following this tutorial, and everything works fine except that I don't have an internet connection on the client while connected to VPN. http://www.howtoforge.com/internet-and-lan-over-vpn-using-openvpn-linux-server-windows-linux-clients-works-for-gaming-and-through-firewalls My VPS server config is as follows (Ubuntu): dev tun proto udp port 1194 ca /etc/openvpn/easy-rsa/keys/ca.crt cert /etc/openvpn/easy-rsa/keys/server.crt key /etc/openvpn/easy-rsa/keys/server.key dh /etc/openvpn/easy-rsa/keys/dh1024.pem user nobody group nogroup server 10.8.0.0 255.255.255.0 persist-key persist-tun status /var/log/openvpn-status.log verb 3 client-to-client push "redirect-gateway local def1" #set the dns servers push "dhcp-option DNS 8.8.8.8" push "dhcp-option DNS 8.8.4.4" log-append /var/log/openvpn comp-lzo plugin /usr/lib/openvpn/openvpn-auth-pam.so common-auth My client config is as follows (Windows 7): dev tun client proto udp remote XXX.XXX.XXX.XXX 1194 resolv-retry infinite nobind persist-key persist-tun ca ca.crt cert stefan.crt key stefan.key comp-lzo verb 3 auth-user-pass redirect-gateway local def1 I've turned off the firewall on the server for testing purposes (it doesn't help), and tried both wired and wireless connecting on the client. I've tried many Google results... but nothing seems to help. Can you help me? Thanks so far...

    Read the article

  • Where can I find a useful multi-language Unicode font for Mac OS X?

    - by Stephen Jennings
    On every browser I've tried (Firefox, Safari, Chrome, and Omniweb), when I go to a web page containing somewhat less-common characters, I can't see the glyphs. For example, on the Wikipedia page for the Bengali Language, the very first line contains a string of squares; on Windows, I can see the Bengali writing. Firefox does display code points on the Coptic Language article, but not Bengali. I'm not sure why. On Windows, as long as I have the Arial Unicode MS font installed, these characters fall back to that font and display properly. Mac OS X doesn't seem to ship with a font containing these Unicode characters (it has Arial Unicode MS, but it must be a subset of the Windows version because Bengali doesn't display in that font). I checked on my Snow Leopard DVD and I installed "Additional Fonts" from the Optional Installs package, but I'm still missing many languages. Is there any good, free font that contains a large collection of languages? I know creating fonts is difficult and time-consuming, but it seems like including at least one font like this with operating systems should be standard by now.

    Read the article

  • httpd Redirect / Rewrite .com to .org

    - by David W
    I am trying to redirect a www.example.com to www.example.org. I cannot figure out what I'm doing wrong. I have ensured that mod_rewrite is enabled in httpd.conf with: LoadModule rewrite_module modules/mod_rewrite.so I further verify this by running: httpd -M and getting rewrite_module (shared) included in the results. Later in the same httpd.conf file is the VirtualHost directive where I am trying to perform the rewrite: <VirtualHost *:80> Options +FollowSymlinks RewriteEngine On RewriteCond %{HTTP_HOST} ^example.com [NC] RewriteRule ^(.*)$ http://www.example.org/$1 [R=301,NC,L] ServerAdmin [email protected] DocumentRoot /var/www/html ServerName example.org ServerAlias www.example.org *.example.org <Directory "/var/www/html"> Options Includes FollowSymLinks AllowOverride All Order allow,deny Allow from all </Directory> ErrorLog /var/www/logs/error_log CustomLog /var/www/logs/access_log common </VirtualHost> As we can see, we are following SymLinks in the directory (which I believe is a requirement), AND we allow All Overrides (which meets another requirement). But obviously I'm still doing something wrong. Can you spot it?

    Read the article

  • How to install DBD::mysql on OS X Server 10.6?

    - by Zoran Simic
    Trying to install DBD::mysql on OS X Server 10.6 (mac mini server). But I'm missing the mysql headers apparently. Since mysql is already part of OS X Server 10.6, I would like to NOT install anything else (no fink or darwin ports installs), just whatever's needed to get DBD::mysql installed and working. Do you know how I could do that? Do I have to install the headers somewhere? And if so, where? (again: I don't want to install another version of mysql on the box, want to use the version it came with). Is there a way to install DBD::mysql without compiling any C files? This is the error I get (the actual error is much longer, but these are the most meaningful bits, this is the first error reported). Checking if your kit is complete... Looks good Unrecognized argument in LIBS ignored: '-pipe' Note (probably harmless): No library found for -lmysqlclient Multiple copies of Driver.xst found in: /Library/Perl/5.10.0/darwin-thread-multi-2level/auto/DBI/ /System/Library/Perl/Extras/5.10.0/darwin-thread-multi-2level/auto/DBI/ at Makefile.PL line 907 Using DBI 1.611 (for perl 5.010000 on darwin-thread-multi-2level) installed in /Library/Perl/5.10.0/darwin-thread-multi-2level/auto/DBI/ Writing Makefile for DBD::mysql cp lib/DBD/mysql.pm blib/lib/DBD/mysql.pm cp lib/DBD/mysql/GetInfo.pm blib/lib/DBD/mysql/GetInfo.pm cp lib/DBD/mysql/INSTALL.pod blib/lib/DBD/mysql/INSTALL.pod cp lib/Bundle/DBD/mysql.pm blib/lib/Bundle/DBD/mysql.pm gcc-4.2 -c -I/Library/Perl/5.10.0/darwin-thread-multi-2level/auto/DBI -I/usr/include -fno-omit-frame-pointer -pipe -D_P1003_1B_VISIBLE -DSIGNAL_WITH_VIO_CLOSE -DSIGNALS_DONT_BREAK_READ -DIGNORE_SIGHUP_SIGQUIT -DDBD_MYSQL_INSERT_ID_IS_GOOD -g -arch x86_64 -arch i386 -arch ppc -g -pipe -fno-common -DPERL_DARWIN -fno-strict-aliasing -I/usr/local/include -Os -DVERSION=\"4.014\" -DXS_VERSION=\"4.014\" "-I/System/Library/Perl/5.10.0/darwin-thread-multi-2level/CORE" dbdimp.c In file included from dbdimp.c:20: dbdimp.h:22:49: error: mysql.h: No such file or directory dbdimp.h:23:45: error: mysqld_error.h: No such file or directory dbdimp.h:25:49: error: errmsg.h: No such file or directory

    Read the article

< Previous Page | 246 247 248 249 250 251 252 253 254 255 256 257  | Next Page >