Search Results

Search found 10893 results on 436 pages for 'failed'.

Page 251/436 | < Previous Page | 247 248 249 250 251 252 253 254 255 256 257 258  | Next Page >

• 1080p Screen resolution problem after 10.04 to 12.04 update

  - by Ale

  I have a Samsung LCD 40" with a NVidia GeForce 6150SE nForce 430 Card. I recently upgraded from 10.04 to 12.04 and the best resolution I can get is 1360x768. I've tried the propietary drivers available on the repository kmod:nvidia_current kmod:nvidia_173_updates kmod:nvidia_current_updates kmod:nvidia_96 kmod:nvidia_96_updates kmod:nvidia_173 I've also downloaded latest from NVidia's Web, version: 295.40. But still no luck. With Nouveau driver, I can only get 1024x768. I know there is no problem with my hardware (video card, cable and monitor), I was using it perfectly on 10.04. Can anybody suggest something else I could try, to get my 1920x1080 resolution back? Thanks in advance. Here are some more information, that I got reading other similar posts on askubuntu. $ lspci | grep VGA 00:0d.0 VGA compatible controller: NVIDIA Corporation C61 [GeForce 6150SE nForce 430] (rev a2) $ xrandr xrandr: Failed to get size of gamma for output default Screen 0: minimum 320 x 240, current 1360 x 768, maximum 1360 x 768 default connected 1360x768 0 0 0mm x 0mm 1360x768 50.0 52.0* 1024x768 51.0 800x600 53.0 54.0 55.0 680x384 56.0 57.0 640x480 58.0 576x432 59.0 512x384 60.0 400x300 61.0 62.0 63.0 320x240 64.0

  Read the article

• How to keep the trunk stable when tests take a long time?

  - by Oak

  We have three sets of test suites: A "small" suite, taking only a couple of hours to run A "medium" suite that takes multiple hours, usually ran every night (nightly) A "large" suite that takes a week+ to run We also have a bunch of shorter test suites, but I'm not focusing on them here. The current methodology is to run the small suite before each commit to the trunk. Then, the medium suite runs every night, and if in the morning it turned out it failed, we try to isolate which of yesterday's commits was to blame, rollback that commit and retry the tests. A similar process, only at a weekly instead of nightly frequency, is done for the large suite. Unfortunately, the medium suite does fail pretty frequently. That means that the trunk is often unstable, which is extremely annoying when you want to make modifications and test them. It's annoying because when I check out from the trunk, I cannot know for certain it's stable, and if a test fails I cannot know for certain if it's my fault or not. My question is, is there some known methodology for handling these kinds of situations in a way which will leave the trunk always in top shape? e.g. "commit into a special precommit branch which will then periodically update the trunk every time the nightly passes". And does it matter if it's a centralized source control system like SVN or a distributed one like git? By the way I am a junior developer with a limited ability to change things, I'm just trying to understand if there's a way to handle this pain I am experiencing.

  Read the article

• Randomly Freezes - How Can I Diagnose the Problem?

  - by j0rd4n

  At random times, Ubuntu 10.04 freezes, and I have to do a hard shutdown. It was upgraded from 9.10 which didn't freeze. First, is this is common problem with a quick answer, and if not, what can I do to diagnose it? I've tried checking application/kernel logs, but nothing gives me a clue as to what caused the problem. My guess, is that since the OS froze, no logs could be updated. Ideas? SOLUTION: Solved it. My particular problem was my graphics card (integrated Radeon 9000 series). netconsole revealed I was getting the error: "reserve failed for wait". After trial-and-error, I manually configured my video card and disabled hardware acceleration. Completely fixed the issue. Here is what I did: Manually Created xorg.conf Ubuntu automatically configures xorg.conf and doesn't use a file. To edit this file, you have to tell Ubuntu to explicitly create one and then edit it. Here are the steps: Restart system Hold Shift as GRUB boots Select root terminal in GRUB login menu Execute: X -config xorg.conf.new Copy: cp xorg.conf.new /etc/X11/xorg.conf Disable Hardware Acceleration The following is specific to my Radeon card, but I'm sure other cards have a similar setup. Edit xorg.conf Find "Device" section for graphics card Uncomment "NoAccel" option and set to "True" Save + reboot Hope that helps.

  Read the article

• WIN7 and Ubuntu lost after Installing ubuntu 12.04 and win7 dual system ,I have no OS on my laptop now

  - by abos

  Here is the procedure: In the morning I installed ubuntu using a USB directly without config any thing to my win7 system. After install complete, ubuntu installation software tell me to reboot.And everything is just find. While rebooting, there is NO UBUNTU system for me to select,and my laptop go straight to log in using WIN7. NO ubuntu shows on WIN7's configuration(Default System). Log in ubuntu using usb(try ubuntu without installation), I can find ubuntu's filesystem was already there. Formatting the disk on WIN7's disk management, rearranging them to other disk.Still having no trouble with WIN7. In the afternoon try a few times of installation and uninstallation of ubuntu. still shows no sign of selecting ubuntu system. In the evening another trial while installing ubuntu with the third option of: installing ubuntu alongside with INW7, erase win7 and install ubuntu. somethingelse --- my check failed with configuartion for what comes out with the 'something else' option,reboot. And I have no system now with some cmd tips say: Reboot and Select proper Boot Device or Insert Boot Media in selected Boot device and press a key. Files those on win7's orginal file system and Ubuntu filesystem can still be found when I 'try ubuntu without installation'. 5.But I just got no OS when I reboot my laptop normally.

  Read the article

• How to get Nvidia graphics working on Sony Z laptop?

  - by projectshave

  I have an older Sony VAIO Z 590 laptop with switchable graphics between Intel and Nvidia GeForce 9300M. It is NOT Optimus. I did a clean install of Ubuntu 12.04. Everything works, but it's using Unity 2D with the Intel drivers. I've tried loading the Nvidia drivers from "Additional Drivers", but it says "this driver is activated but not currently in use". When I run "nvidia-settings", an error window pops up to say "You do not appear to be using the NVIDIA X drivers." "lspci" shows both graphics cards. Let me know if I should add more info. How do I get the Nvidia graphics and Unity 3D working? More info: $ lshw -short -class display H/W path Device Class Description ============================================== /0/100/1/0 display G98 [GeForce 9300M GS] /0/100/2 display Mobile 4 Series Chipset Integrated Graphics C $ glxinfo name of display: :0 Xlib: extension "GLX" missing on display ":0". Xlib: extension "GLX" missing on display ":0". Xlib: extension "GLX" missing on display ":0". Xlib: extension "GLX" missing on display ":0". Xlib: extension "GLX" missing on display ":0". Error: couldn't find RGB GLX visual or fbconfig Xlib: extension "GLX" missing on display ":0". Xlib: extension "GLX" missing on display ":0". Xlib: extension "GLX" missing on display ":0". Xlib: extension "GLX" missing on display ":0". Xlib: extension "GLX" missing on display ":0". Xlib: extension "GLX" missing on display ":0". Xlib: extension "GLX" missing on display ":0". Excerpts from Xorg.0.log: [ 16.373] (II) LoadModule: "glx" [ 16.373] (II) Loading /usr/lib/x86_64-linux-gnu/xorg/extra-modules/libglx.so [ 16.386] (II) Module glx: vendor="NVIDIA Corporation" [ 16.386] compiled for 4.0.2, module version = 1.0.0 [ 16.386] Module class: X.Org Server Extension [ 16.386] (II) NVIDIA GLX Module 295.49 Tue May 1 00:09:10 PDT 2012 [ 16.608] (II) NVIDIA dlloader X Driver 295.49 Mon Apr 30 23:48:24 PDT 2012 [ 16.608] (II) NVIDIA Unified Driver for all Supported NVIDIA GPUs [ 17.693] (EE) Failed to initialize GLX extension (Compatible NVIDIA X driver not found)

  Read the article

• Employers and intellectual property 2

  - by Rick

  I have a question about intellectual property, I am currently a manager in a small manufacturing firm. The owners are driven by greed and don't appreciate the development process of complex machinery and are happy just to send things out half done. I on the other hand think that it should be done properly as breakdown in the field can be costly, embarrassing. They seem to have all of us running around doing most of the work out of hours using the attitude of "Be grateful to have a job" yet no one has a contract or any security or any agreement in place. For a couple of the projects i am using PLC's and doing the code in my own time and the testing during company time, and i am aware that they cannot support their own machines if i left, but as i created the code in my own time who owns it? The have asked my to put in a shutdown code for a maintenance request after a given length of time, could this be classed as criminal damage or anything illegal apart from immoral? (we sell the machines with 12 month warrantee, shut down after) But as time goes on I'm getting rather fed up of the companies attitude toward the client. I am considering keeping the clients as my own and get them to contact me directly In the shutdown code. By doing something like this is a trial version contact me for a full license? I wouldn't feel bad for my current employer as he is not afraid to S***t on people as he has been evolved in numerous law suits and has over 30 failed companies leaving people and customers high and dry, we have took the company this far on the reputation of the workers and and i can see things heading like all the other companies he has owned and taking our reputations with him. So i suppose now i have set the scene, if i code into it to contact me directly in the shutdown could there be any legal impact on me, as i rightly or wrongly think i own the code and designs? Cheers R

  Read the article

• What is the value of checking in failing unit tests?

  - by Adam W.

  While there are ways of keeping unit tests from being executed, what is the value of checking in failing unit tests? I will use a simple example: Case Sensitivity. The current code is case sensitive. A valid input into the method is "Cat" and it would return an enum of Animal.Cat. However, the desired functionality of the method should not be case sensitive. So if the method described was passed "cat" it could possibly return something like Animal.Null instead of Animal.Cat and the unit test would fail. Though a simple code change would make this work, a more complex issue may take weeks to fix, but identifying the bug with a unit test could be a less complex task. The application currently being analyzed has 4 years of code that "works". However, recent discussions regarding unit tests have found flaws in the code. Some just need explicit implementation documentation (ex. case sensitive or not), or code that does not execute the bug based on how it is currently called. But unit tests can be created executing specific scenarios that will cause the bug to be seen and are valid inputs. What is the value of checking in unit tests that exercise the bug until someone can get around to fixing the code? Should this unit test be flagged with ignore, priority, category etc, to determine whether a build was successful based on tests executed? Eventually the unit test should be created to execute the code once someone fixes it. On one hand it shows that identified bugs have not been fixed. On the other, there could be hundreds of failed unit tests showing up in the logs and weeding through the ones that should fail vs. failures due to a code check-in would be difficult to find.

  Read the article

• Problem in multi booting Ubuntu 12.04 with existing Windows XP, 7 and 8 in 500GB HDD with 5 Partitions

  - by Dhruva

  Here's my case. I have 500GB HDD with 5 Partitions with XP, Windows7 and Windows8 RP in the first three. As per one of the instruction I've seen in this forum, I did shrink my 4th Partition to create a 30GB unallocated free space to install Ubuntu 12.04. But, when next I'm trying to boot the Ubuntu CD and choosing "Something Else", its only recognizing my 500GB HDD in whole as "/sda" and not reading the free 30GB space separately to install Ubuntu in it as suggested in the instruction mentioned in this forum. I've also tried to install in from within Windows7, by mounting the Ubuntu ISO file and using the .exe file and instruction thereupon (choosing free drive, user name, installation size, etc.), but that also failed after the PC restarted to continue the installation, showing as error for file extension, partition something error. One thing to be noted that the PC I'm trying to install Ubuntu in it is my Home PC and doesn't have any internet connection. Hence, no updates or otherwise online help. What shall I do?? Kindly suggest. Sorry if I made some grammatical mistakes as English is not my first language. Thanks in advance.

  Read the article

• Nvidia GeForce Gt-520M-cn on intel dh61ww Ubuntu 12.04

  - by j goseeped

  hi people i hope you can help a little bit , i appreciate your time look: i have a this desktop i7 2600, 8gb ram ddr3, board intel dh61ww, Geforce Nvidia GT520-cn 2Gb ddr3, i just install ubuntu 64bits 12.04 kernel 3.2.0-23-generic , i want to setup two monitors samsung led 22" and get start mi video card 1) i download and installed nvidia driver 295.59 and also try with 302.17 to apt-update and upgrade, apt-get install build-essential linux-headers-$(uname -r), apt-get remove --purge nvidia*, apt-get remove --purge xserver-xorg-video-nouveau, vim /etc/modprobe.d/blacklist.conf blacklist vga16fb blacklist nouveau blacklist rivafb blacklist nvidiafb blacklist rivatv sh NVIDIA.run, sudo service lightdm start, reboot, nvidia-xorgconf 2)after reboot i get 800x600 and nvidia-settings say this. You do not appear to be using the NVIDIA X driver. Please edit your X configuration file (just run nvidia-xconfig as root), and restart the X server. 3) i change a little bit xorg.conf to set up a resolution to work property 4) i dont have any image in the monito and i dont have any option on Nvidia X server settings lspci | grep VGA 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 01:00.0 VGA compatible controller: NVIDIA Corporation GF119 [GeForce GT 520] (rev a1) egrep -i 'glx|nvidia' /var/log/Xorg.0.log [ 12.005] (II) LoadModule: "glx" [ 12.005] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so [ 12.575] (II) Module glx: vendor="NVIDIA Corporation" [ 12.585] (II) NVIDIA GLX Module 302.17 Tue Jun 12 16:22:45 PDT 2012 [ 12.585] (II) Loading extension GLX [ 13.037] (EE) Failed to initialize GLX extension (Compatible NVIDIA X driver not found) [ 13.044] (II) config/udev: Adding input device HDA NVidia HDMI/DP,pcm=3 (/dev/input/event10) [ 13.044] (II) config/udev: Adding input device HDA NVidia HDMI/DP,pcm=7 (/dev/input/event9) glxinfo | grep direct Xlib: extension "GLX" missing on display ":0.0". Error: couldn't find RGB GLX visual or fbconfig sorry my english is no very well. and thanks guys

  Read the article

• I Can't run the Netbeans but I installed successfully

  - by David

  I'm new to Ubuntu as well as Netbeans. I installed Netbeans, and I've made sure to install all the JDKs and JREs I could find. It installed without errors. I also saw this question and made sure I followed all the instructions there as well. I never got any error messages of any kind. So far as I know, it installed okay. However, when I try to run Netbeans, I get the message in the bottom of the Netbeans IDE like this: ant -f /root/NetBeansProjects/samp1 -Djsp.includes=/root/NetBeansProjects/samp1/build/web/one.jsp -DforceRedeploy=false -Dclient.urlPart=/one.jsp -Ddirectory.deployment.supported=true -Djavac.jsp.includes=org/apache/jsp/one_jsp.java -Dnb.wait.for.caches=true run /root/NetBeansProjects/samp1/nbproject/build-impl.xml:774: The libs.CopyLibs.classpath property is not set up. This property must point to org-netbeans-modules-java-j2seproject-copylibstask.jar file which is part of NetBeans IDE installation and is usually located at <netbeans_installation>/java<version>/ant/extra folder. Either open the project in the IDE and make sure CopyLibs library exists or setup the property manually. For example like this: ant -Dlibs.CopyLibs.classpath=a/path/to/org-netbeans-modules-java-j2seproject-copylibstask.jar BUILD FAILED (total time: 0 seconds)

  Read the article

• Ubuntu 14.04: Fine tuning Touchpad for ThinkPad S431

  - by ramgorur

  I am using Ubuntu 14.04 on Lenovo ThinkPad S431. The touchpad is very bumpy, tricky to use. Slides down with a small touch, sometimes jerks erratically. I have tried to modify the settings in /usr/share/X11/xorg.conf.d/50-synaptics.conf file as below -- Section "InputClass" Identifier "touchpad catchall" Driver "synaptics" MatchIsTouchpad "on" MatchDevicePath "/dev/input/event*" Option "JumpyCursorThreshold" "250" Option "VertResolution" "100" # Option "HorizResolution" "65" # Option "MinSpeed" "1" # Option "MaxSpeed" "1" # Option "AccelerationProfile" "1" # Option "AdaptiveDeceleration" "8" # Option "ConstantDeceleration" "1" # Option "VelocityScale" "128" Option "HorizHysteresis" "150" Option "VertHysteresis" "150" EndSection There are lots of options here, does anyone know how to get a fine-tuned values for the above options (for ThinkPad S431)? The Hysteresis values seems to alleviate the problem a little bit, but failed to get a perfect result. EDIT: According to this bug report for ThinkPad X230 (+X230t), I set these values and quite good for now -- Option "VertResolution" "100" Option "HorizResolution" "65" Option "MinSpeed" "1" Option "MaxSpeed" "1" Option "AccelerationProfile" "2" Option "AdaptiveDeceleration" "16" Option "ConstantDeceleration" "16" Option "VelocityScale" "32" Option "HorizHysteresis" "50" Option "VertHysteresis" "50" and then you need to increase the cursor speed manually from the Unity mouse settings. But I am still looking for a fully functional (possibly with all the gestures) and a fine-tuned touchpad settings for S431. Further help is appreciated.

  Read the article

• How do I get 1366x768 resolution on 12.04?

  - by Megan

  I am on an HP Envy 14, and the proper resolution that I should be using is 1366x768. This is not an option and I am stuck on 1024x768. I am using Linux 12.04. lspci | grep VGA: 00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 02) 01:00.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI Madison [Radeon HD 5000M Series] I've tried to add the resolution as a mode in xorg.conf but that does not work. Please any help would be appreciated. I'm new to Linux and just got my dual boot working but this resolution issue is killing me. Edit1 I just tried using the xrandr command: xrandr --newmode "1368x768_60.00" 85.25 1368 1440 1576 1784 768 771 781 798 -hsync +vsync But I get an error: xrandr: Failed to get size of gamma for output default Edit2 lsmod returns the following: Module Size Used by vesafb 13844 1 rfcomm 47604 12 bnep 18281 2 parport_pc 32866 0 ppdev 17113 0 snd_hda_codec_hdmi 32474 1 arc4 12529 2 joydev 17693 0 hid_logitech_dj 18594 0 i915 472941 5 uvcvideo 72627 0 usbhid 47199 1 hid_logitech_dj hid 99559 2 hid_logitech_dj,usbhid psmouse 87692 0 iwlwifi 332525 0 mac80211 506816 1 iwlwifi videodev 98259 1 uvcvideo snd_hda_codec_idt 70795 1 mei 41616 0 btusb 18288 2 v4l2_compat_ioctl32 17128 1 videodev hp_accel 25976 0 lis3lv02d 19876 1 hp_accel hp_wmi 18092 0 sparse_keymap 13890 1 hp_wmi input_polldev 13896 1 lis3lv02d drm_kms_helper 46978 1 i915 drm 242038 2 i915,drm_kms_helper i2c_algo_bit 13423 1 i915 serio_raw 13211 0 snd_hda_intel 33773 5 snd_hda_codec 127706 3 snd_hda_codec_hdmi,snd_hda_codec_idt,snd_hda_intel snd_hwdep 13668 1 snd_hda_codec bluetooth 180104 23 rfcomm,bnep,btusb cfg80211 205544 2 iwlwifi,mac80211 snd_pcm 97188 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec mac_hid 13253 0 snd_seq_midi 13324 0 snd_rawmidi 30748 1 snd_seq_midi snd_seq_midi_event 14899 1 snd_seq_midi snd_seq 61896 2 snd_seq_midi,snd_seq_midi_event fglrx 3263886 0 snd_timer 29990 2 snd_pcm,snd_seq snd_seq_device 14540 3 snd_seq_midi,snd_rawmidi,snd_seq snd 78855 20 snd_hda_codec_hdmi,snd_hda_codec_idt,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_ra wmidi,snd_seq,snd_timer,snd_seq_device wmi 19256 1 hp_wmi video 19596 1 i915 intel_ips 18174 0 soundcore 15091 1 snd snd_page_alloc 18529 2 snd_hda_intel,snd_pcm lp 17799 0 parport 46562 3 parport_pc,ppdev,lp r8169 62099 0 I have installed ATI/AMD proprietary FGLRX graphics driver. But there is another one called ATI/AMD proprietary FGLRX graphics driver (post-release updates) which I have trouble installing because it gives me an error and tells me to look at some sort of jockey log.

  Read the article

• Expanding RAID-5

  - by Garry

  I'm new to RAID and trying to get my head around things. I have owned a Drobo in the past (which I liked) but it failed. Here's a hypothetical scenario: Assume I set up a RAID-5 array consisting of four 1TB hot-swappable 2.5" SATA drives. I name this volume 'My Data'. By my calculations, that would give me 2.7TB of usable space and the ability to recover if a single drive fails. I have a few questions: What happens if I pull out a single 1TB drive and replace it with a 2TB drive? Would the array automatically rebuild itself with no issues? Would the maximum capacity remain 2.7TB? If number (1) above is true and the array rebuilds itself with three 1TB drives one 2TB drive what would happen if I then pulled another 1TB drive out and stuck in a 2TB drive (you can see where I'm going here can't you). Would I eventually be able to gain more storage by gradually adding bigger drives? From a practical point of view, how much input is required from me as the end user whilst these drives are being pulled out and put in? On the Drobo, the storage space just automagically handles itself. Would I have to be actively involved in telling Ubuntu what was going on or would any of it be automated? Thanks in advance,

  Read the article

• Dim (NEARLY blank) laptop screen, secondary screen works - why?

  - by LIttle Ancient Forest Kami

  My laptop screen is (almost) black while my secondary screen is fine. I believe it to be backlight / brightness related. Problem description it starts when I start the laptop system loads and works fine, just screen has problems I can see the screen though very faintly / dimly - it's hard to see anything which ain't very white e.g. starting screen has big Thinkpad logo in white, large font - I can see it, though very dimly second screen works very well Official backligtht debugging: using acpi setting as prescribed there for Thinkpads didn't help I can see an entry in /sys/class/backlight/ and it changes when I press hotkeys for brightness (current backlight power for instance goes up or down) acpi-off didn't helpm neither did acpi_backlight=vendor Hardware data Laptop is Thinkpad Edge with glossy screen. 4 processors, 2 cores, exemplary CPU data from cat /proc/cpuinfo reports Genuine Intel i5 (M 480 @ 2.67GHz). OS is Ubuntu Lucid, 10.04 LTS, 64-bit, with Linux generic kernel (2.6.32-44) and GNOME 2.32.2 (though I doubt there lies the problem). $ lspci | grep VGA 01:00.0 VGA compatible controller: ATI Technologies Inc M92 [Mobility Radeon HD 4500 Series] $ lshw -C display *-display description: VGA compatible controller product: M92 [Mobility Radeon HD 4500 Series] vendor: ATI Technologies Inc physical id: 0 bus info: pci@0000:01:00.0 version: 00 width: 32 bits clock: 33MHz capabilities: pm pciexpress msi bus_master cap_list rom configuration: driver=radeon latency=0 resources: irq:33 memory:c0000000-dfffffff(prefetchable) ioport:2000(size=256) memory:f0300000-f030ffff memory:f0320000-f033ffff(prefetchable) Driver I was NOT running any proprietary drivers, just checked with "Hardware drivers". There is one for ATI that is suggested there, though I didn't need it so far. UPDATE: changing the driver to proprietary one (ATI/AMD FGLRX) didn't help. Tried and failed Resetting / running on power or battery / charging / getting rid of static electricity / warming up *doesn't help* This is NOT a blank-screen problem, at least it isn't following official Ubuntu black-screen diagnostics - I can see my screen, though barely. What I will try next: - check last updates I've made - IIRC I am running on nomodeset already, but will verify this Any ideas how to proceed best? What is most probable cause?

  Read the article

• Do the benefits of Resin/Quercus outweigh the overhead?

  - by Craige

  Lately, I've been looking more and more into Resin + Quercus as a technology to develop an application of mine. The reason I started looking into it was that this application has high reporting needs, a lot of which cannot (or realistically, should not) be created in real-time. Java would offer a nice backend to queue and generate reports. Also, with Quercus I would be able to develop my data models in Hibernate, and use them "from PHP", thus effectively stretching these models across front and back-end. This same concept would also apply to any front/back-end common business logic, which could be developed in Java libraries. Now, the downside is that whichever front-end (PHP) MVC Framework I choose (my goal was Symfony 2), it is unlikely to work without some heavy modification, if it can work at all. Quercus is a pretty close implementation of PHP, and is supposed to be compatible with PHP5.3, so namespaces and closures SHOULDN'T be a problem, but when I tried to run an existing Symfony 1.4 app, I failed miserably. So, my question to you is, do you think the benefits of Resin + Quercus outweigh the overhead of using a not-so-perfect/stable implementation of PHP? If this were your application, and your goal was and end-product, rather than educational purposes, what would you decide?

  Read the article

• shrink ext4 partition

  - by user276851

  My question is similar to Move ext4 partition, but the challenge I couldn't figure out is how to shrink a partition from the start. So suppose originally the partition (with raid) is like this. (************** /dev/md127 ***************) After resizing, I want to achieve like this. (*** unallocated ***)(**** /dev/md127 ****) Note, I cannot use gparted, and parted does not support ext4. The commands I have tried so far, % resize2fs -p /dev/md127 1676G # <== This is good. % lvreduce -L 1676G /dev/md127 Path required for Logical Volume "md127" Please provide a volume group name Run `lvreduce --help' for more information. Failed here, I guess it may be because the underlying partition is primary and the lvreduce only works on logical? Anyway, no idea. Then after that, I am thinking to create another partition right after this one, copy the data to that partition, and remove this one, like. 1. (************** /dev/md127 ***************) 2. (**** /dev/md127 ****)(*** new partition **) 3. (*** unallocated ****)(**** /dev/md127 ****) Thanks for the help.

  Read the article

• how to fully unit test functions and their internal validation

  - by Patrick

  I am just now getting into formal unit testing and have come across an issue in testing separate internal parts of functions. I have created a base class of data manipulation (i.e.- moving files, chmodding file, etc) and in moveFile() I have multiple levels of validation to pinpoint when a moveFile() fails (i.e.- source file not readable, destination not writeable). I can't seem to figure out how to force a couple particular validations to fail while not tripping the previous validations. Example: I want the copying of a file to fail, but by the time I've gotten to the actual copying, I've checked for everything that can go wrong before copying. Code Snippit: (Bad code on the fifth line...) // if the change permissions is set, change the file permissions if($chmod !== null) { $mod_result = chmod($destination_directory.DIRECTORY_SEPARATOR.$new_filename, $chmod); if($mod_result === false || $source_directory.DIRECTORY_SEPARATOR.$source_filename == '/home/k...../file_chmod_failed.qif') { DataMan::logRawMessage('File permissions update failed on moveFile [ERR0009] - ['.$destination_directory.DIRECTORY_SEPARATOR.$new_filename.' - '.$chmod.']', sfLogger::ALERT); return array('success' => false, 'type' => 'Internal Server Error [ERR0009]'); } } So how do I simulate the copy failing. My stop-gap measure was to perform a validation on the filename being copied and if it's absolute path matched my testing file, force the failure. I know this is very bad to put testing code into the actual code that will be used to run on the production server but I'm not sure how else to do it. Note: I am on PHP 5.2, symfony, using lime_test(). EDIT I am testing the chmodding and ensuring that the array('success' = false, 'type' = ..) is returned

  Read the article

• Ubuntu live cd : black screen and blinking cursor

  - by IFasel

  I try to install ubuntu 12.04 on my computer. I can get to the purple screen on the live cd but then, if I choose "Installing Ubuntu", I have a black screen with a cursor blinking (and nothing else happens). My PC : acer aspire M3920, CPU i5-2300, 8 Gb RAM, NVIDIA gt 405. What I already tried : I tried with 12.04 and 13.04 daily build I tried with a live usb and with a live dvd I tried the following boot options : nomodset, acpi=off I googled a lot and it seems that it could be a graphic card problem. Do you know any other boot options that I could try ? UPDATE This is not a duplicate : I've tried all the common boot options (nomodeset, noacpi...) and it doesn't change anything. With the option "no splash" (instead of "quiet splash"), I can see what happens before the forever-blinking cursor : [sdg] no caching mode present [sdg] assuming drive cache : write trough ata8.00: excetion Emask 0x52 ... frozen ata8 : SError : { RecovData RecovComm UnrecovData...} ata8.00 : failed command : IDENTIFY PACKET DEVICE ... ata8.00 : status : { DRDY } ata8 : hard resetting link Does somebody know what it means ? N.B. astonishingly, Puppy Linux boots fine (but Debian, Fedora and Ubuntu do not) Solution In fact, it was not a graphic card problem. I had to disconnect the dvd drive and connect it to another free sata connector (I don't really understand why Ubuntu had trouble with this connector and Windows 7 not). After that, everything worked fine.

  Read the article

• I cannot boot Ubuntu from WUBI install with windows 7, get an error message every time

  - by Tom

  i have tried several times to install ubuntu using wubi, i can't use a disc as i have a notebook computer and there is no optical drive. the download and installation all seem to work well but whenever i try to boot ubuntu at the windows 7/ubuntu menu it comes up with this error screen. I have used both the C: drive and the D: drive to install Ubuntu several times each, it's always unsuccessful. "Windows has failed to start. a recent hardware or software change might be the cause. To fix the problem: Insert your windows installation disc and restart your computer Choose your language settings and then click 'next' Click repair your computer. If you do not have this disc, contact your system administrator or computer manufacturer for assistance. File: \ubuntu\winboot\wubildr.mbr Status: 0xc000000F Info: The selected entry could not be loaded because the application is missing or corrupt." I use an ASUS x501a with windows 7. What do i do to fix this? I want to be able to dual boot Windows 7 and ubuntu. Thanks a lot :)

  Read the article

• Dual monitor display 12.04?

  - by MrMonty

  I have 2 beautiful 27" asus monitors. I started trying out Ubuntu 12.04 and now only one works and thats vga .. Any help here cause I'm stumped. I have a bfg tech nivida Geforce 8800 gt 512mb and I'm trying to fix this. Getting this error Wen i try to configure the xorg file Failed to set MetaMode (1) 'DFP-0: 1280x1024 @1280x1024 +0+0, DFP-1: 1280x1024 @1280x1024 +1280+0' (Mode 2560x1024, id: 50) on X screen 0. ........................................................................................... This is the xorg.conf ....................................................... nvidia-settings: X configuration file generated by nvidia-settings nvidia-settings: version 295.33 (buildd@allspice) Fri Mar 30 15:25:24 UTC 2012 Section "ServerLayout" Removed Option "Xinerama" "1" Removed Option "Xinerama" "0" Removed Option "Xinerama" "1" Identifier "Layout0" Screen 0 "Screen0" 0 0 InputDevice "Keyboard0" "CoreKeyboard" InputDevice "Mouse0" "CorePointer" Option "Xinerama" "0" EndSection Section "Files" EndSection Section "InputClass" Identifier "Mouse Remap" MatchProduct "Saitek Cyborg R.A.T.7 Mouse" MatchDevicePath "/dev/input/event*" Option "ButtonMapping" "1 2 3 4 5 6 7 8 9 0 0 0 0 0 0" EndSection Section "InputDevice" # generated from default Identifier "Keyboard0" Driver "kbd" EndSection Section "Monitor" # HorizSync source: edid, VertRefresh source: edid Identifier "Monitor1" VendorName "Unknown" ModelName "Ancor Communications Inc VE247" HorizSync 30.0 - 83.0 VertRefresh 50.0 - 76.0 Option "DPMS" EndSection Section "Monitor" # HorizSync source: edid, VertRefresh source: edid Identifier "Monitor0" VendorName "Unknown" ModelName "Ancor Communications Inc VE247" HorizSync 30.0 - 83.0 VertRefresh 50.0 - 76.0 Option "DPMS" EndSection Section "Device" Identifier "Device1" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "Quadro FX 1500" BusID "PCI:1:0:0" Screen 1 EndSection Section "Device" Identifier "Device0" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "Quadro FX 1500" EndSection Section "Screen" Identifier "Screen1" Device "Device1" Monitor "Monitor1" DefaultDepth 24 Option "TwinView" "0" Option "TwinViewXineramaInfoOrder" "DFP-1" Option "metamodes" "DFP-1: 1280x1024 +0+0" SubSection "Display" Depth 24 EndSubSection EndSection Section "Screen" Removed Option "TwinView" "0" Removed Option "metamodes" "DFP-0: 1280x1024 +0+0" Removed Option "TwinView" "1" Removed Option "metamodes" "DFP-0: 1280x1024 +0+0, DFP-1: 1280x1024 +1280+0" Removed Option "TwinView" "0" Removed Option "metamodes" "DFP-0: 1280x1024 +0+0" Identifier "Screen0" Device "Device0" Monitor "Monitor0" DefaultDepth 24 Option "TwinView" "1" Option "TwinViewXineramaInfoOrder" "DFP-0" Option "metamodes" "DFP-0: 1280x1024 +0+0, DFP-1: 1280x1024 +1280+0; DFP-1: 1280x1024_60 +0+0" SubSection "Display" Depth 24 EndSubSection EndSection Section "Extensions" Option "Composite" "Disable" EndSection FILE ^^^^

  Read the article

• Authenticate with Django 1.5

  - by gorjuce

  I'm currently testing django 1.5 and a custom User model, but I've some problems. I've created a User class in my account app, which looks like: class User(AbstractBaseUser): email = models.EmailField() activation_key = models.CharField(max_length=255) is_active = models.BooleanField(default=False) is_admin = models.BooleanField(default=False) USERNAME_FIELD = 'email' I can correctly register a user, who is stored in my account_user table. Now, how can I log in? I've tried with: def login(request): form = AuthenticationForm() if request.method == 'POST': form = AuthenticationForm(request.POST) email = request.POST['username'] password = request.POST['password'] user = authenticate(username=email, password=password) if user is not None: if user.is_active: login(user) else: message = 'disabled account, check validation email' return render( request, 'account-login-failed.html', {'message': message} ) return render(request, 'account-login.html', {'form': form}) I can correctly register a new User My forms.py which contains my register form class RegisterForm(forms.ModelForm): """ a form to create user""" password = forms.CharField( label="Password", widget=forms.PasswordInput() ) password_confirm = forms.CharField( label="Password Repeat", widget=forms.PasswordInput() ) class Meta: model = User exclude = ('last_login', 'activation_key') def clean_password_confirm(self): password = self.cleaned_data.get("password") password_confirm = self.cleaned_data.get("password_confirm") if password and password_confirm and password != password_confirm: raise forms.ValidationError("Password don't math") return password_confirm def clean_email(self): if User.objects.filter(email__iexact=self.cleaned_data.get("email")): raise forms.ValidationError("email already exists") return self.cleaned_data['email'] def save(self): user = super(RegisterForm, self).save(commit=False) user.password = self.cleaned_data['password'] user.activation_key = generate_sha1(user.email) user.save() return user My question is: Why does authenticate give me None? I know I'm trying to authenticate() with an email as username but is that not one of the reasons to use a custom User model?

  Read the article

• Neverending issues with grub (ubuntu 14.04 on ASUS with Win8 dual boot)

  - by Mariana

  This is the most frustrating issue I have ever run into using Ubuntu and Windows in the same machine. I have an ASUS K46CB, 6GB RAM and preinstalled Windows 8.1 64-bits. I have successfully installed Ubuntu 14.04 LTS, also 64-bits. To do so,I followed this tutorial whenever possible. I only failed on the disable secure boot part: there is no 'Secure-boot' or even UEFI mention in my BIOS! Screenshots from other BIOS of the same model show the option under Boot, but in mine there is absolutely none. Because of this, I cannot boot into Ubuntu. The computer loads straight into Windows. I tried running boot repair, but got an error (i can show the log, but it's pretty long). Does anyone know how to fix this issue? UPDATE I reinstalled Ubuntu. Same problem, goes straight to Window. Boot-Repair informs me that i am using Windows in Legacy mode. It excecuted with no errors this time, but after restarting GRUB was still missing. I can't turn off Secure Boot yet. UPDATE I tried using Boot Repair to install grub on a boot-grub 1mb partition. Still boots straight to windows. I feel like punching something

  Read the article

• VMware9 fails to launch Virtual OS. Ubuntu 12.10 64bit (Unable to change virtual machine power state: Pipe connection has been broken.)

  - by pst007x

  Another issue I need help with. I use VMware for work on Ubuntu 12.04. However for some reasons my VMware Workstation software generates the following error: Unable to change virtual machine power state: Failed to power on '/home/pst007x/vmware/Windows 7 x64/Windows 7 x64.vmx'. Transport (VMDB) error -14: Pipe connection has been broken. Product: VMware® Workstation Version: 9.0.0 build-812388 Host OS Version: 3.5.0-18-generic Ubuntu 12.10 64bit Kernel Linux 3.5.0-18-generic I have seen patches, but nothing works, and the patches are not maintained, broken links. PLEASE NOTE: I know that this has been asked, but there was no answer given that resolves this issue. Unfortunately I have changed all my office and personal PC's to Ubuntu, and use Win7 in a vm, however since 12.10, vm now fails to launch. For me this is a catastrophe, and makes Ubuntu useless for me to use! I am in a desperate situation here, is there is anyone that can offer any help I would be truly appreciative. I have looked on the VMware forums and the only solution is offered for Fedora, but the people posting there are not clear about what the solution is! thanks PLEASE DO NOT CLOSE THIS QUESTION! I have tried everywhere to find a solution, but I have come up blank... Patches referenced to in other posts do not work in this version of VMware...

  Read the article

• How do I 'see' an external USB drive connected directly to my Broadband Router?

  - by The Cougar Kid

  This is a very frustrating problem! I have a small home network with several dual boot Ubuntu / Windows computers. I have recently upgraded my Broadband connection and the new router permits the direct attachment of an external USB drive which can back up all of the household's computers. There are no problems when booted under Windows, and there were no problems with older versions of UBUNTU, but since upgrading to 11.10 I can no longer "see" the drive. I used to find it via Network / Windows Network / Home / name of Router, but under 11.10 the same method yields an error message Unable to mount location Failed to retrieve share list from server. Can anyone help please? Starting Nmap 5.21 ( http://nmap.org ) at 2011-12-21 10:06 GMT Stats: 0:02:02 elapsed; 0 hosts completed (1 up), 1 undergoing Service Scan Service scan Timing: About 50.00% done; ETC: 10:10 (0:01:56 remaining) Nmap scan report for 192.168.1.254 Host is up (0.0097s latency). Not shown: 998 filtered ports PORT STATE SERVICE VERSION 554/tcp open rtsp? 7070/tcp open realserver? Service detection performed. Please report any incorrect results at http://nmap.org/submit/ . Nmap done: 1 IP address (1 host up) scanned in 152.38 seconds sudo tail -n 30 /var/log/syslog [sudo] password for alaric: Dec 21 10:05:42 UPSTAIRS2U wpa_supplicant[882]: WPA: Group rekeying completed with 00:01:3b:8b:63:1a [GTK=TKIP]

  Read the article

• Can't Log Into Ubuntu 12.04

  - by Razick

  Yesterday, after turning on Ubuntu, I logged into a Gnome session. A few minutes later, I tried switching to Unity for a change. Unfortunately, the background and my desktop icons loaded, but the system bar and launcher failed to load even after several minutes. Unity had always worked fine for me. I then tried the guest account, and it worked fine on both Unity and Gnome. However, the problem with my account got worse; I couldn't log into any desktop at all anymore. I would type in my password and press enter and it would just sit there doing nothing. The computer no longer responded in any way, so I had to hold the power button and reboot. The same problem happened repeatedly. Earlier today, I tried to get on again. I found that I hadthe same problem, when I tried to log in, the computer no longer locked up, but instead flashed a black screen with theconsole output and what seemed to be an error message before returning to the log in screen. It was to quick for me to read, about 1/4-1/2 second. I'd really appreciate some help as I have some important files that are not backed up yet. I can't transfer the files to a new account, or even make a new account because I tried taking the password off my account so now I can't authenticate from the guest to perform root functions. I'd really appreciate some help as I have some important files that are not backed up yet. Thanks.

  Read the article

< Previous Page | 247 248 249 250 251 252 253 254 255 256 257 258  | Next Page >