Search Results

Search found 16355 results on 655 pages for 'lua c connection'.

Page 251/655 | < Previous Page | 247 248 249 250 251 252 253 254 255 256 257 258  | Next Page >

• IP-restricted port forwarding with iptables

  - by Tom

  For an example, I have two authorized client computers, 1.1.1.1 and 2.1.1.1. My server running iptables is 3.1.1.1 and my firewalled web server is 4.1.1.1. When one of the authorized client IPs connects to 3.1.1.1 on port 80, I would like the connection to be forwarded to 4.1.1.1 on port 8888. If any other IP attempts to connect I would like it to refuse/drop the connection. What iptables config would accomplish this? Is there something more specific out there that would be better suited for this job?

  Read the article

• Extend university wifi network [migrated]

  - by asfasdoiuh ouhouhouh

  i live in a university campus and i can get wifi signal on the outside of my window but not in the house. The solution i use at the moment is a usb wifi dongle outside connected to my laptop but the lack of an internal antenna make the connection quite unreliable at times. So i was trying to find another solution to improve the reception of my network. One idea is to setup a router on the outside (in a place with stronger signal) and redirect the connection inside the house with an ethernet cable but the problem is that our Uni Wifi is managed by a capitve portal (BlueSocket with DNS redirection to login page) and the authentication has to happen on the mac address that connect to the net (so the client appliance in this case). If I use a router with Mac-Clone capability i will be able to be redirected trough the captive portal on my laptop computer and login from there or i need to setup my router to fill in the login page by itself? There are other hardware/software solutions i can use to get what i want? Thank you all

  Read the article

• L2TP Site to Site VPN issues

  - by Chris Lively

  I have a windows 2008 r2 server that needs to establish a VPN connection to a remote VPN server. We're using the L2TP protocol with a pre-shared key. I initially used the New Demand Dial interface wizard. Then I went into properties on the interface and set the type of VPn to L2TP/IPSec and put the key under the advanced settings. The error I received when attempting to connect is: An error occured during connection of the interface. A Demand Dial Router attempted to connect over a port that was reserved for Remote Access Clients only.

  Read the article

• Linux - Block ssh users from accessing other machines on the network

  - by Sam

  I have set up a virtual machine on my network for uni project development. I have 6 team members and I don't want them to SSH in and start sniffing my network traffic. I already have set the firewall on my W7 pcs to ignore any connection attempts from the Virtual Machine, but would like to go a step further and not allow any network access from the VM to other machines on my network. Team members will be access the VM by SSH. The only external port forwarded is to vm:22. The VM is running in VirtualBox on a bridged network connection. Running latest Debian. If someone could tell me how to do this I would be much obliged.

  Read the article

• How to connect MTS MBlaze

  - by murali_ma

  i have installed ubuntu 11.04 inside the windows xp. i have MTS Mblaze USB Modem. (my service provider is MTS MBlaze,india) i want to use Mblaze into ubuntu so that i did the following steps for make connecting the device. from the task bar->edit connections->mobile broadband->choose country->mts mblaze and ok i give username and password ([email protected] and password MTS. ok now i enable mobile broadband , MTS MBlaze connection1(connection name) from task bar. steps followed from "http://randomshandom.wordpress.com/2010/12/20/how-to-connect-mts-mblaze-device-in-ubuntu-10-10-11-04/#more-3" for the first time it successfully connected and browse the internet. after i restart the system i connect it. it does not connected. it shows Modem network disconnected. i accessed many times and delete the connection and recreated but i does not help me. if i try to connect device i think it the search the network, i saw the wave signal. img Image for showing problem:

  Read the article

• If Nvidia Shield can stream a game via wifi, why can I not do the same via ethernet to any other PC?

  - by Enigma

  I think it absurd that a wireless game streaming solution is the *first to hit the market when a 1000mbps+ Ethernet connection would accomplish the same feat with roughly 6x the available bandwidth. I can only assume that there must be some reason behind this or a limitation preventing this, but what? 150mbps wifi is in no way superior to a 1000mbps LAN connection aside from well wireless mobility. Not only that but I have a secondary laptop and desktop which should by hardware comparison completely outperform anything the Tegra in the Nvidia Shield can do. Is this all just a marketing scheme to force people to buy the shield for the streaming benefit? Chief among these is that NVIDIA’s Shield handheld game console will be getting a microconsole-like mode, dubbed “Shield Console Mode”, that will allow the handheld to be converted into a more traditional TV-connected console. In console mode Shield can be controlled with a Bluetooth controller, and in accordance with the higher resolution of TVs will accept 1080p game streaming from a suitably equipped PC, versus 720p in handheld mode. With that said 1080p streaming will require additional bandwidth, and while 720p can be done over WiFi NVIDIA will be requiring a hardline GigE connection for 1080p streaming (note that Shield doesn’t have Ethernet, so this is presumably being done over USB). Streaming aside, in console mode Shield will also support its traditional local gaming/application functionality. - http://www.anandtech.com/show/7435/nvidia-consolidates-game-streaming-tech-under-gamestream-brand-announces-shield-console-mode ^ This is not acceptable for me for a number of reasons not to mention the ridiculousness of having a little screen+controller unit sitting there while using a secondary controller and screen instead. That kind of redundant absurdity exemplifies how wrong of a solution that is. They need a second product for this solution without the screen or controller for it to make sense... at which point your just buying a little computer that does what most other larger computers do better. All that is required, by my understanding, is the ability to decode H.264 video compression and transmit control/feedback so by any logical comparison, one (Nvidia especially) should have no difficulty in creating an application for PC's (win32/64 environment) that does the exact same thing their android app does. I have 2 video cards capable of streaming (encoding) H.264 so by right they must be capable of decoding it I would think. I haven't found anything stating plans to allow non-shield owners to do this. Can a third party create this software or does it hinge on some limitation that only Nvidia can overcome? (*) - perhaps this isn't the first but afaik it is the first complete package.

  Read the article

• Scripted SOA Diagnostic Dumps for PS6 (11.1.1.7)

  - by ShawnBailey

  When you upgrade to SOA Suite PS6 (11.1.1.7) you acquire a new set of Diagnostic Dumps in addition to what was available in PS5. With more than a dozen to choose from and not wanting to run them one at a time, this blog post provides a sample script to collect them all quickly and hopefully easily. There are several ways that this collection could be scripted and this is just one example. What is Included: wlst.properties: Ant Properties build.xml soa_diagnostic_script.py: Python Script What is Collected: 5 contextual thread dumps at 5 second intervals Diagnostic log entries from the server WLS Image which includes the domain configuration and WLS runtime data Most of the SOA Diagnostic Dumps including those for BPEL runtime, Adapters and composite information from MDS Instructions: Download the package and extract it to a location of your choosing Update the properties file 'wlst.properties' to match your environment Run 'ant' (must be on the path) Collect the zip package containing the files (by default it will be in the script.output location) Properties Reference: oracle_common.common.bin: Location of oracle_common/common/bin script.home: Location where you extracted the script and supporting files script.output: Location where you want the collections written username: User name for server connection pwd: Password to connect to the server url: T3 URL for server connection, '<host>:<port>' dump_interval: Interval in seconds between thread dumps log_interval: Duration in minutes that you want to go back for diagnostic log information Script Package

  Read the article

• Spawning HTTPD processes

  - by felix001

  Can any confirm how Apache spawns new children ? As in if I connect to a webserver (HTTP 1.0 / no keep alive) and issue a HTTP /GET I will be spawned a new HTTPD child. If then issue another HTTP /GET then a new TCP connection will be built. However will I use the same child process of would I spawn a new one ? Also if I was using HTTP 1.1 (with keep-alive) and reused the same TCP connection, would the httpd process/spawning be any different to that if I wasnt using keepalive ? Thanks,

  Read the article

• Windows Server 2008 R2 - Can't connect RDP over the Internet

  - by Jonathan DeMarks

  I have two networks: Domain and Public, Domain is a VPN connection and Public is the local connection to the network. This is not a domain controller or a DNS/DHCP server. I can connect via RDP from the local network (192.168.1.), from the VPN network (10.1.2.), and from the VPN network over the internet. I cannot connect from the internet (anywhere besides where the server is VPN'd) Wireshark indicates that the server is getting packets, and the audit log is indicating that the packets are being dropped. Advanced Firewall has explicit options to allow RDP, and has no deny policies. I have also tried turning Firewall off completely to no avail. I'm really lost on this one.

  Read the article

• IIS + PHP + Page with lots of images = Intermittent 403 errors

  - by samJL

  I am using an up-to-date Server 2008 R2 Datacenter, running IIS 7.5 and PHP 5.3.6/FastCGI On PHP pages with lots of images (60+), some of the images fail to load It is not always the same images-- on each page refresh an image that worked previously may not load, while an image that did not now does Looking at the Net tab in Firebug reveals that the failing image requests are 403 errors All of the images are located on the server in question, and the images directory has the correct permissions I believe this problem is the result of a limit on requests All of my attempts at researching this problem point to maxConnections setting in IIS, yet mine is set at the highest/default of 4294967295 (maxBandwidth too) I am also running a ColdFusion site on the same IIS installation, and it does not suffer from 403's on pages with lots of images I am left thinking that there is another connection limit (in PHP or FastCGI?) overriding the IIS connection limit I don't see anything that looks like a request limit in the php.ini, what am I missing? Any help would be appreciated, thank you

  Read the article

• How to setup a wired local area network in Windows 7?

  - by user883434

  I am using a Lenovo ThinkPad X200 and want to se tup a wired local area network. How could I achieve this? Actually, my question is very simple. I just want to connect to the internet and I have a cable connection at home. So, I just want to plug the cable line to my notebook (x200) so that I can access the internet via the cable. But I dont know how to setup a local area connection in notebook. Since it automatically appear in my desktop, but not in my notebook. Thanks!

  Read the article

• Cannot SSH anymore, what went wrong?

  - by lbwtz2

  I use to ssh to a remote server (no rsa-key, just password). Now the server do not accept the connection any more and throw me this error: ssh_exchange_identification: Connection closed by remote host While I can google a little to find a fix I can't figure out what went wrong since I haven't touched anything on the machine since last login. Can you help me find the cause? EDIT: Inspecting the logs I've found these: /var/auth.log /var/log/auth.log:Dec 26 16:40:32 vps sshd[15567]: error: fork: Cannot allocate memory /var/log/auth.log:Dec 26 16:41:05 vps sshd[15567]: error: fork: Cannot allocate memory /var/log/auth.log:Dec 26 16:43:47 vps sshd[15567]: error: fork: Cannot allocate memory /var/log/auth.log:Dec 27 03:20:06 vps sshd[15567]: error: fork: Cannot allocate memory /var/log/auth.log:Dec 27 16:15:02 vps sshd[15567]: error: fork: Cannot allocate memory And in the same span-time I've also found a lot of these: /var/log/auth.log:Dec 26 13:00:01 vps CRON[1716]: PAM unable to dlopen(/lib/security/pam_unix.so): libcrypt.so.1: cannot map zero-fill pages: Cannot allocate memory /var/log/auth.log:Dec 26 13:00:01 vps CRON[1716]: PAM adding faulty module: /lib/security/pam_unix.so What are these?

  Read the article

• How to Install Broadcom Wireless Drivers (BCM43xx)

  - by Fer1805

  I'm having serious problems installing the Broadcom drivers for Ubuntu. It worked perfectly on my previous version, but now, it is impossible. I'm a user with no advance knowledge in Linux, so I would need clear explanations on make, compile, etc. Edit: For the command: "lspci | grep Network", I get the following message: 06:00.0 Network controller: Broadcom Corporation BCM4311 802.11b/g WLAN (rev 01) For the command: iwconfig, i get the following: lo no wireless extensions. eth0 no wireless extensions. When i follow the following steps (from the above link), there are a NO error message at all: open the 'Synaptic Package Manager' and search for bcm uninstall the bcm-kernel-source package make sure that the firmware-b43-installer and the b43-fwcutter packages are installed type into terminal: cat /etc/modprobe.d/* | egrep '8180|acx|at76|ath|b43|bcm|CX|eth|ipw|irmware|isl|lbtf|orinoco|ndiswrapper|NPE|p54|prism|rtl|rt2|rt3|rt6|rt7|witch|wl' (you may want to copy this) and see if the term blacklist bcm43xx is there if it is, type cd /etc/modprobe.d/ and then sudo gedit blacklist.conf put a # in front of the line: blacklist bcm43xx then save the file (I was getting error messages in the terminal about not being able to save, but it actually did save properly). reboot 'End of procedure' Before (not ubuntu 11.04), if i wanted to connect wireles, i just went to the icon at the upper side of the screen, click, showed ALL the wireless network available, and done. Now, the only options i see are: Wired Network Auto Eth0 Disconnect VPN Enable networking Connection information Edit connection. lspci -vnn | grep Network showed: Broadcom Corporation BCM4322 802.11a/b/g/n Wireless LAN Controller [14e4:432b] hope above info is enough for your help.

  Read the article

• ssl_error_rx_record_too_long error on IIS - site was working, suddenly stopped

  - by JK01

  I am suddenly getting this error connecting to localhost IIS on my development machine. It has been working fine for ages, and now suddenly has this error in Firefox: Secure Connection Failed An error occurred during a connection to localhost. SSL received a record that exceeded the maximum permissible length. (Error code: ssl_error_rx_record_too_long) I have googled and found no clear explanation. In IE it says: Internet Explorer cannot display the webpage\ In Chrome it says: Oops! This link appears to be broken.

  Read the article

• How do I know when my on-board ethernet is dead? (Realtek 8112L LAN controller w/ AI NET2 )

  - by Usagi

  So I have an ASUS P7P55D-E Pro motherboard. It has an on-board Realtek 8112L LAN controller w/ AI NET2. I suspect that my LAN controller is dead but I don't really know for sure. This is what I know thus far: Everything was working, I have a triple booted system and ethernet was functional under Linux, Win7, and OSX. My ethernet is no longer functional under all three of the operating systems. I was experiencing random momentary internet outages before everything finally went dark. I don't know much about the AI NET BIOS tool but I believe it just checks for ethernet problems before you boot into an operating system. In any case, it doesn't find a connection upon boot. I've checked the connection on a couple of other machines and everything worked fine. I think I already know the answer to my question, but are there any other possible explanations, or is it dead?

  Read the article

• SQL Server 2012 LocalDB

  - by user3061846

  I´m a noobie so please be patient ! I developed an app using C# and SQL Server Express 2012 with a local database, my connection string is"Data Source=localhost ; Initial Catalog = scalnet ; Integrated Security=SSPI; Trusted_Connection=Yes"; Everything worked ok till the time I made a setup and tried to install my app in another computer. My first question is: - What version of SQL should I install is this machine? it should be as ligth as possible. - I tried to install SQL exprees 2012 but it gives me an error when I execute my app "A network related or instance specific error occurred while establishing a ..... (provider:Named Pipes Provider, error:40 - Could not open a connection to SQL server." This probably should be a problem with the server configuration but I have no ideia how to solve this... Can anyone point me to the rigth direction ? ? Thanks

  Read the article

• Tracing what program is making a network connnection? (CentOS)

  - by Airjoe

  I was wondering if it is possible to find out which process is trying to make a specific network connection. On a server I support which hosts websites for about 200 users, the iptables firewall keeps blocking, as it should, a connection to 212.117.169.139 on port 80. Firefox reports this as an attack page (and at the least is obvious spam, if not malicious). It seems something on this server is trying to access this site for some reason, and although it's being blocked successfully, the requests seem to be going through every two to sixty seconds and I'd like to be able to find what process or script is doing this so I can handle it appropriately. Besides doing a grep to try and find if this IP is in some file (which probably won't even work because it may be working by hostname or it may be encoded), is there any way to find out some more information? Thanks!

  Read the article

• How can I disrupt my roommate's BitTorrent?

  - by bob

  We're on a 50 mb/s Comcast connection and our connection right now is coming in under 1.5 mb/s. Our roommate left for a week with BitTorrent running (Azureus client, we think). Our latency is approaching 300 ms. His door is locked up tight, and both his machine and the router for the house are located inside. I've even flipped the power breaker in the house and that barely works for 2 minutes. His laptop keeps on running, and once the cable modem and router come back up and the machine reconnects, the torrents resume in earnest. I've been running nmap and identified his IP on our LAN. Is there anything I can do over the LAN to make his torrents start to fail or slow down?

  Read the article

• Cisco: changing VTP mode server/client to transparent

  - by J. Smith

  I have around 40 L2 switches (2960, 3560, 3500, 3750) running in VTP client mode and one L3 switch (6500) running in VTP server mode, all connected together. I would like to switch everything in VTP transparent mode without any interruption of service. I've already test on a poc version with 3 switches (Catalyst 2950, 3560 and 3750). Using serial and SSH connection, it is seems working but i'm not sure it is enough representative compare to the real network. Knowing that the VTP Pruning is enabled, I am wondering what would be the best procedure to proceed the changement. I've read that we could lost connection by keeping it enabled. Should I change the server or clients first? Is it important to change the VTP domain and VTP Pruning parameters?

  Read the article

• IPSec VPN IP addresses

  - by Randomblue

  I have an IPSec VPN on my Windows 7 machine (all using the native Windows 7 gateway). The host I am connecting to has different ISAKMP "Phase 1" and "Phase 2" IP addresses. As I understand, the Phase 1 address is that of the IPsec endpoint, to which I can connect just fine. The Phase 2 address is found in their "crypto map", and the addresses need to match. At the moment, both my Phase 1 and Phase 2 addresses are configured the same. On my side, I get the error "Error 791: The L2TP connection attempt failed because security policy for the connection was not found" How can I configure the Phase 2 IP address for my Windows 7 IPSec VPN to be different to the IPSec endpoint address?

  Read the article

• Windows 2012 remote access can't connect

  - by Gelo Volro

  I have installed Windows Server 2012 for about 9 months ago. Earlier I could connect to my server with an external IP perfectly, but the license for the remote desktop services has ended. First, I thought it was the reason, why I couldn't use my server as RDP-server, to which users may connect. But, than in web I read, that it's possible to use windows native features, just to remove the RDP services, which are trial and the server will work as RDP-server, but with some limitations ( for e.g. such free RDP service may accept only 1 connection and other connection will be disconnected etc ). Is it true, that it's possible? If yes, please give a piece of advice, how should I repair it. Because I don't want to use TightVNC or other stuff. Thanks!

  Read the article

• Why is file sharing over internet still working, despite all firewall exceptions for filesharing being disabled?

  - by Triynko

  Every exception in my windows server firewall that starts with "File and Printer Sharing" is disabled (ordered by name, so that includes domain, public (active), and private profiles). The Network and Sharing Center's options for everything except password protected sharing are off. Why would I still be able to access a network share on that server via an address like "\\my.server.com\" over the internet? The firewall is on for all profiles and blocking incoming connections by default. A "netstat -an" command on the server reveals the share connection is occurring over port 445 (SMB). I restarted the client to ensure it was actually re-establishing a new connection successfully. Is the "Password protected sharing: On" option in Network and Sharing Center bypassing the firewall restrictions, or adding some other exception somewhere that I'm missing? EDIT: "Custom" rules are not the problem. It's the "built-in" rules for Terminal Services that was the problem. Can you believe port 445 (File Sharing Port) has to be wide open to the internet to use Terminal Services Licensing?)

  Read the article

• VPN Authentication Credentials (Local/Remote Identifiers) For Remote Access VPN

  - by thatidiotguy

  So I am trying to set up a remote access VPN using the free ShrewSoft vpn client: https://www.shrew.net/software I want to use a PSK as the authentication mechanism combined with XAuth so that a connection requires a valid username/pass combo. Under the authentication tab this particular VPN Client however is asking for a Local Identity and a Remote Identity. The options for Local Identity Type are: Fully Qualified Domain Name User Fully Qualified Domain Name IP Address Key Identifier The options for Remote Identity are: Any Fully Qualified Domain Name User Fully Qualified Domain Name IP Address Key Identifier My current thinking is that I can use the Fully Qualifed Domain Name provided by the remote firewall for the Remote Identity, but I do not know what it wants for local identity. Just to stress: I am not trying to set up a site to site VPN. Can anybody shed any light on what I am missing here? A screenshot can be provided if that would be helpful. The current error I am getting during the connection is: IKE Responder: Proposed IKE ID mismatch

  Read the article

• Route a specific user's traffic via VPN but still allow local networking

  - by wbg

  So, I want to route certain traffic via a VPN connection and the rest via my normal Internet connection. I want to run several different programs and most of them don't support binding to a specific network interface (tun0 in my case). I've managed to send a specific user's traffic via the VPN following the answers given here: iptables - Target to route packet to specific interface? But unfortunately, when I run a server that connects to the Internet and has a web interface running on a local IP (127.0.0.1/192.168.0.*), all the Internet traffic correctly goes via tun0, but I'm unable to connect to the web interface from a local IP as a different user. When I log in as the VPN-ified user, I can access services running on local IPs, but other users/machines can't access any servers I start. Can anyone point me in the right direction?

  Read the article

• Sharing VPN access between two computers on the LAN

  - by Axelle Ziegler

  I have VPN access to several machines in my office from my home machine. I'd like to be able to access those machines from another computer on my LAN, without setuping a second VPN access. Both computers are Windows 7 machines. Is there a way for my "main" computer to share its VPN access to another machine on the LAN? How would one setup this share? I don't think "simple" Internet connection sharing fits my needs because: My LAN already has its own DHCP/Router to access the Internet, and I'd like to keep it this way I can't access the Internet through my VPN connection

  Read the article

< Previous Page | 247 248 249 250 251 252 253 254 255 256 257 258  | Next Page >