Search Results

Search found 8616 results on 345 pages for 'primitive types'.

Page 251/345 | < Previous Page | 247 248 249 250 251 252 253 254 255 256 257 258  | Next Page >

• How can I stop SipVicious ('friendly-scanner') from flooding my SIP server?

  - by a1kmm

  I run an SIP server which listens on UDP port 5060, and needs to accept authenticated requests from the public Internet. The problem is that occasionally it gets picked up by people scanning for SIP servers to exploit, who then sit there all day trying to brute force the server. I use credentials that are long enough that this attack will never feasibly work, but it is annoying because it uses up a lot of bandwidth. I have tried setting up fail2ban to read the Asterisk log and ban IPs that do this with iptables, which stops Asterisk from seeing the incoming SIP REGISTER attempts after 10 failed attempts (which happens in well under a second at the rate of attacks I'm seeing). However, SipVicious derived scripts do not immediately stop sending after getting an ICMP Destination Host Unreachable - they keep hammering the connection with packets. The time until they stop is configurable, but unfortunately it seems that the attackers doing these types of brute force attacks generally set the timeout to be very high (attacks continue at a high rate for hours after fail2ban has stopped them from getting any SIP response back once they have seen initial confirmation of an SIP server). Is there a way to make it stop sending packets at my connection?

  Read the article

• what type of laptop do I need to run a amd64 or i386 VM?

  - by Frank Schwieterman

  I was running an amd64 build of Ubuntu on a VM on a Windows host which was also amd64. Later I found I could not run the same amd64 iso on my laptop, which is intel without hyper-V. I was confused I thought chipset mattered, but maybe it does not. When buying a PC or Apple, is there anything to check about the chipset to make sure it can run different types of VMs? In my case, I was trying to run ubuntu on a Thinkpad T520. Per answer below, I did need to enable some bios settings. I'm still having some issues. Running ubuntu on virtual box, when I try to use ubuntu-12.10-server-amd64.iso for the CD/DVD device to start a new VM, virtualbox complains "Failed to open the CD/DVD image . Could not get the storage format of the medium (VERR_NOT_SUPPORTED). When I try to use ubuntu-12.10-server-i386.iso the ISO is accepted, but then the VM complains "FATAL: No bootable medium found! System halted." I had been using an amd64 iso on my home PC which is amd64 and it works fine, which is why I suspected CPU mismatch was the problem at first. But it seems like I'm having issues, and maybe this superuser thread can be used to verify the cpu is irrelevant in this case.

  Read the article

• torrent downloads not showing on Squid log

  - by noobroot

  hello, i have just a few months working as sysadmin, hence i still have lots to learn, first thing id like to do is as follows: We have an OpenBSD 4.5 box acting like firewall,dns,cache etc, the box has 2 network cards, one conected directly to the internet and the other to our switch, i used to work with sarg for the log analysis but then changed to the much faster free-sa. I use a daily free-sa report to check the bandwidth usage and report our top 5 bandwidth consumers (3 days a week being #1 and you will be buying the pizzas :D, we are a small company ~20 so we are very familiar). this was working really good until recently, one of us required to download some stuff via torrent (~3GB) and since the pizza rule is active for non-work related downloads, he told me (verified) that his download was indeed work related so i would dismiss that 3GB off his quota, but to my surprise the log didnt showed that 3GB, since his ip consumption was only around 290MB. More recently, since the FIFA world cup started, we know that some of the employees are watching the match's streaming, we know it and we dont care about it since, like already stated, we are a small company so we dont have restrictive policies, we all can chat, watch youtube, download anything we want BUT we are only allowed 300MB a day otherwise you'll get in the top5-pizza-board, anyway, that streaming consumption is also not showing in the free-sa reports. So my question is, why is these data being excluded from the reports? im thinking that the free-sa reports list only certain types of things but im also thinking if are the squid logs the ones that are not erm... logging these conections. Any help, guide, advice or clarification is appreciated.

  Read the article

• What format should I convert my iTunes Videos to?

  - by Aequitarum Custos

  Recently got Daniusoft Media Converter, and was about to strip the DRM off my iTunes library, then I found I had a huge decision to make. Converting my music seems obvious, to MP3, however the video formats, I'm at a loss on. It has "optimized" formats for all types of video players such as iPhone, Zune, Droid (which I own), and just a huge list! I bought several seasons of House and a few movies, though I don't know which format would be optimal to not lose quality. While I love my Droid, I have no intention on watching full episodes or movies on it, and I have a feeling that would reduce quality. One of the options sections is HD Video, and it has HD MPEG-4 Video (*.mp4). That one seems like it would be the best format to convert to without losing quality, but again, I'm unsure. Has anyone used this software, or have general expertise in video formats to give a recommendation on what file format I should convert my videos to? Format requirements: No loss in quality Portability would be ideal (as in, will play on my Windows and potentially MAC, and streamable to a bigscreen).

  Read the article

• nginx: js file loads indifferently every refresh

  - by poymode

  I have this nginx problem wherein a js file in a rails app loads indifferently. Whenever I try to access the JS file in the browser and refresh the page, the scrollbar changes length meaning sometimes it loads half the js page, sometimes the whole and sometimes just a part of it. the js file size is 71K. my nginx server is on different server,separate from my rails app. when I try to access the js file directly through the app server, lets say 10.48.30.150:3000/javascripts/file.js it works fine and doesnt show any half-loaded page. but when I use the nginx server which upstreams the rails app, it shows the indifferent page loads. here is my nginx http conf error_log /usr/local/nginx/logs/error.log; pid /usr/local/nginx/logs/nginx.pid; events { worker_connections 1024; } http { include mime.types; default_type application/octet-stream; server_names_hash_bucket_size 256; access_log /usr/local/nginx/logs/access.log; sendfile on; #tcp_nopush on; keepalive_timeout 0; tcp_nodelay on; #gzip on; #gzip_min_length 4096; #gzip_buffers 16 8k; #gzip_types application/x-javascript text/css text/plain; large_client_header_buffers 4 8k; client_max_body_size 2G; include /usr/local/nginx/conf.d/*.conf; }

  Read the article

• How do I troubleshoot nginx not recognizing passenger?

  - by Jade

  Issue: nginx does not seem to recognize my rails application Symptoms: When the server starts up, it shows the "Welcome to nginx!" message instead of my Rails application. Nginx seems to be using the local nginx path instead of the Rails root I specified: 2010/04/18 06:29:06 [error] 783#0: *1 "/usr/local/nginx/html/blog/index.html" is not found (2: No such file or directory), client: 1.2.3.4, server: www.farmerjade.com, request: "GET /blog/ HTTP/1.1", host: "www.farmerjade.com" I used [RVM and Passenger Setup on NGINX][1] to install nginx and passenger on a virtual machine. Here is my nginx configuration: user farmerjade; worker_processes 1; ... http { include mime.types; default_type application/octet-stream; passenger_ruby /home/farmerjade/.rvm/bin/passenger_ruby; passenger_root /home/farmerjade/.rvm/gems/ree-1.8.7-head/gems/passenger-2.2.11; ... server { listen 80; server_name www.farmerjade.com; root /home/farmerjade/farmerjade/public; passenger_enabled on; rails_env development; ... I'd appreciate any help anyone has to offer -- I'm quite new to nginx.

  Read the article

• Rails 3 + Nginx + Passenger -- Routing index

  - by Bijan

  I have no index.html file in my public folder. My rails routes file routes this, and it works fine when I run 'rails server' on my machine. I'm trying to deploy the app. I have passenger and nginx running When I run rails server on my local machine, it works fine. But it's just trying to access static file when I try to access it on the production server. Here's my nginx conf: worker_processes 1; #pid logs/nginx.pid; events { worker_connections 1024; } http { passenger_root /usr/lib/ruby/gems/1.9.1/gems/passenger-3.0.2; passenger_ruby /usr/bin/ruby; include mime.types; default_type application/octet-stream; sendfile on; keepalive_timeout 65; server { listen 80; server_name mmjconsult.com; root /www/mmjs/public; access_log logs/host.access.log; passenger_enabled on; } } Thank you for any help. I really appreciate it.

  Read the article

• Consulting: Organizing site/environment documentation for customers?

  - by ewwhite

  Over time, I've taken on consulting and contract engineering work for various clients. More recently, customers are asking for certain types of documentation. These are small businesses and typically do not have dedicated technical staff. Within a single company, Wiki/Confluence/Sharepoint, etc. all make sense as a central repository for documentation and environment information. I struggle with finding a consistent method to deliver the following information to discrete customers. I'm shooting for a process that's more portable, secure and elegant than a simple spreadsheet or the dreaded binder full of outdated information. Important IP addresses, DHCP scope, etc. Network diagram (if needed). Administrative usernames and passwords and management URLs. Software license keys. Support contracts and warranty information. Vendor support contacts and instructions. I know there are other consultants here. Any suggestions or tips on maintaining documentation across multiple environments in a customer-friendly format? How do you do it?

  Read the article

• Nginx server 301 Moved permanently

  - by user145714

  When I did a curl -v http://site-wordpress.com:81 I received this result: About to connect() to site-wordpress.com port 81 (#0) Trying ip... connected Connected to site-wordpress.com (ip) port 81 (#0) GET / HTTP/1.1 User-Agent: curl/7.19.7 (x86_64-unknown-linux-gnu) libcurl/7.19.7 NSS/3.12.6.2 zlib/1.2.3 libidn/1.18 libssh2/1.2.2 Host: site-wordpress.com:81 Accept: / < HTTP/1.1 301 Moved Permanently < Server: nginx/1.2.4 < Date: Fri, 16 Nov 2012 16:28:19 GMT < Content-Type: text/html; charset=UTF-8 < Transfer-Encoding: chunked < Connection: keep-alive < X-Pingback: The URL above/xmlrpc.php < Location: The URL above Seems like this line in my fastcgi_params is causing grief. fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; If I remove this line , I get HTTP/1.1 200 OK but I get a blank page. This is my config: server { listen 81; server_name site-wordpress.com; root /var/www/html/site; access_log /var/log/nginx/access.log; error_log /var/log/nginx/error.log; index index.php; if (!-e $request_filename){ rewrite ^(.*)$ /index.php break; } location ~ \.php$ { fastcgi_pass 127.0.0.1:9000; # port where FastCGI processes were spawned fastcgi_index index.php; include /etc/nginx/fastcgi_params; include /etc/nginx/mime.types; } location ~ \.css { add_header Content-Type text/css; } location ~ \.js { add_header Content-Type application/x-javascript; } } This config works with ip and port 80. But now I need to use a domain name and port 81, which doesn't work. Could someone please help. Thanks.

  Read the article

• NGINX: How do I calculate an optimal no. of worker processes and worker connections?

  - by bodacious

  Our web app is running on a Linode 2048 server at the moment (~ 2048 GB of RAM) The MYSQL database is on another linode of it's own so this server is really only handling NGINX and and the Rails application. The application itself uses about 185976 of memory per instance (RSS). Our traffic is < 1000 per day and the pages are mostly cached so there are fewer hits to the rails app itself. My question is - how can I calculate optimal NGINX config settings for my app? Below is the current config: worker_processes 1; # pid of nginx master process pid /var/run/nginx.pid; events { worker_connections 1024; } http { access_log /var/log/nginx/access.log; error_log /var/log/nginx/error.log; passenger_root /home/user/.rvm/gems/ree-1.8.7-2011.01@URTV/gems/passenger-3.0.3; passenger_ruby /home/user/.rvm/rubies/ree-1.8.7-2011.01/bin/ruby; include mime.types; default_type application/octet-stream; sendfile on; tcp_nopush on; tcp_nodelay on; # gzip settings gzip on; gzip_http_version 1.0; gzip_comp_level 2; gzip_vary on; gzip_proxied any; gzip_types text/css application/x-javascript text/xml application/xml application/xml+rss text/javascript; # load extra modules from the vhosts directory include /opt/nginx/vhosts/*.conf; } Any advice would be appreciated! :)

  Read the article

• How can I start hostednetwork on Windows 7?

  - by Pirozek

  When I type in admin console command to start hostednetwork netsh wlan start hostednetwork it gives me this: The hosted network couldn't be started. The group or resource is not in the correct state to perform the requested operation. There is a hotfix from Microsoft but it didn't help me. Any advice? C:\Users\Pirozek>netsh wlan show driver Interface name: Wireless Network Connection 3 Driver : D-Link AirPlus DWL-G520 Wireless PCI Adapter(rev .B) Vendor : Atheros Communications Inc. Provider : Atheros Communications Inc. Date : 8.7.2009 Version : 8.0.0.171 INF file : C:\Windows\INF\oem108.inf Files : 2 total C:\Windows\system32\DRIVERS\athrx.sys C:\Windows\system32\drivers\vwifibus.sys Type : Native Wi-Fi Driver Radio types supported : 802.11b 802.11g FIPS 140-2 mode supported : Yes Hosted network supported : Yes Authentication and cipher supported in infrastructure mode: Open None Open WEP-40bit Shared WEP-40bit Open WEP-104bit Shared WEP-104bit Open WEP Shared WEP WPA-Enterprise TKIP WPA-Personal TKIP WPA2-Enterprise TKIP WPA2-Personal TKIP Vendor defined TKIP WPA2-Enterprise Vendor defined Vendor defined Vendor defined WPA-Enterprise CCMP WPA-Personal CCMP WPA2-Enterprise CCMP Vendor defined CCMP WPA2-Enterprise Vendor defined Vendor defined Vendor defined WPA2-Personal CCMP Authentication and cipher supported in ad-hoc mode: Open None Open WEP-40bit Open WEP-104bit Open WEP WPA2-Personal CCMP

  Read the article

• Facter - custom fact, returns empty data set when invoked by Puppet agent

  - by user3684494

  According to this puppet labs article, I can create custom facts from shell scripts. I have created a bash script that returns a single fact, it is packaged in a modules facts.d directory. The module is included on the target system via an ENC class. When invoked by the puppet agent on the target it returns an empty set, when run by hand on the agent it correctly returns the fact. The script has execute permission on the master, but does not have it on the agent. I saw a bug report related to permissions and file types, but that was windows and supposed to be fixed in puppet version 3. What am I doing wrong? ENC definition: --- classes: facttest: Shell script: #!/bin/bash echo "test_fact1=$(hostname)" Permissions: master: -rwxr-xr-x 1 root root ... modules/facttest/facts.d/testfact.sh agent: -rw-r--r-- 1 root root ... /var/lib/puppet/facts.d/testfact.sh Agent message: Fact file /var/lib/puppet/facts.d/testfact.sh was parsed but returned an empty data set Version information: Puppet master: 3.5.1 (Debian) Facter master: 2.0.1 Puppet agent: 3.6.1 (OpenSUSE) Facter agent: 2.0.1

  Read the article

• Which default Database Systems come installed in Microsoft VS2010 Express?

  - by Tonygts

  Appreciate all advice 0n the following questions Which database systems (Ms SQL 2008, MS SQL Compact, or others) comes installed with VS2010 Express edition. SQL Server 2008 R2 Express is free, can we install and integrate with VS2010 Express? How to uninstall those database already come installed? I have installed VS2010 express on Windows 7; just VS2010 components (VB, C#, C++ and Web Developer) and without installing any other things like SQL Express. In the Console Panel-Program & Features' window, the installed list is shown below: Microsoft SQL Server 2008 Setup Support File Microsoft SQL Server 2008 Browser Microsoft SQL Server VSS Writer Microsoft SQL Server Database Publishing Wizard 1.4 Microsoft ASP.NET MVC2 - VWD Express 2010 Tools Microsoft SQL Server 2008 Management Objects Microsoft SQL Server Compact 3.5 SP2 ENU Microsoft SQL Server System CLR Types Microsoft Silverlight 3 SDK Microsoft ASP.NET MVC 2 Microsoft Visual Studio 2010 ADO.NET Entity Framework Tools Visual Studio 2010 Tools doe SQL Server Compact 3.5 SP2 ENU Web Deployment Tool Microsoft Visual Web Developer 2010 Express - ENU Microsoft Visual C++ 2010 Express - ENU Microsoft Visual C# 2010 Express - ENU Microsoft Visual Visual Basic 2010 Express - ENU Microsoft SQL Server 2008 As you can see, Microsoft SQL Server 2008 (last line) and near the top, Microsoft SQL Server Compact 3.5 SP2 ENU and many of their related SQL components such as Microsoft SQL Server 2008 R2 Management Objects are also installed. These are actually installed by installing VS2010 Express, but I have no idea how to use them or verify their valid existence from VS2010. Also, do I have to uninstall them before I install SQL Server 2008 R2, which is the latest version I believe? And what tool is needed to manage and create data source and tables?

  Read the article

• Windows 2008 R2 DHCP Overlapping Scopes

  - by Buska

  We are trying to troubleshoot a scope overlap problem. We have multiple device types we wish to give all different ranges of a 16 bit subnet. IE. X device we wish to give 192.168.2.1-192.168.2.254/16, Y devices we wish to give 192.168.3.1-192.168.3.254/16. We are trying to accomplish this by creating different scopes and using the 60 class identifier. The problem is DHCP won't allow us to give these scopes with 16 bit masks because of the potential overlap. We aren't overlapping the address pool so why does DHCP care and can we work around this? If this isn't possible, how can i assign specific ranges by device type without creating multiple scopes? Any thoughts would be helpful. UPDATE: Entire Scope is 192.168.0.0/16 Gateway is 192.168.1.1/16 Device Hardware A - 192.168.20.1-192.168.20.254/16 Device Hardware B - 192.168.26.1-192.168.26.254/16 Device Hardware C - 192.168.85.1-192.168.85.254/16 We tried to setup multiple scopes for each device type (A,B,C) but couldn't specify a 16 bit mask as Scope A could technically overlap Scope B even thought our start and end addresses don't. I hope this makes more sense. Thanks for your thoughts.

  Read the article

• With puppet, can you have the client ask to be a certain set of roles?

  - by Aitch

  I've recently got my puppetmaster and client up and running and have had the client correctly signed, then requested and applied simple changes, all good. I have a growing number of machines (100). They are not consistently named (historical reasons). They fall into a handful of categories (think of it like: dataserver_type1, dataserver_type2, webserver_type1, webserver_type2....). New instances of these types of machines are added weekly. I don't understand (yet) or cannot see how I can declare a "generic" node of (say) "dataserver_type1" that contains whatever modules it needs, and set something in the client puppet.conf that says "I am a dataserver_type1" without using the hostname/FQDN If I set the node name in the catalog as (say) "my-data-server-type1" - the certified hostname - it picks it up and works. I know you can use patterns for hostnames but as I said, my server names are not consistent, and I can't change them. This seems disingenuous to have to edit a file and manually add a node for each server, when they continue to grow. Edit: Digging deeper, it seems roles may be what I want. But there still seems to be an element whereby the master has contain a list of roles that a specific named server should do. Perhaps what I am asking is, how can a client say "I want to be this role", without the server having to be updated?

  Read the article

• How to make Firefox file associations consistent with Ubuntu file associations?

  - by wbharding

  This seems to be a pretty commonly Google question, but one for which there are no answers. http://www.linuxquestions.org/questions/linux-software-2/firefox-download-mime-types-378902 http://www.birkit.com/content/kubuntu-linux/internet/firefox/fix-file-associations-in-firefox.html Being three links amongst the many. The gist of what I want to accomplish is to have Firefox understand the file associations I download without me having to manually map all of them myself. Gnome knows the file extensions, so I would have expected that Firefox could just use the already-known file mappings there to open the right stuff (as I presume Chrome does). But it doesn't. At least not for me, using Firefox 4, and not by default. When I click on a downloaded file right now, Firefox always has to ask me what application should be used to open the file. A handful of Google results tell me that I can reassociate my file extensions by deleting ~/.mozilla/firefox/[profile name]/mimeTypes.rdf, but while deleting that file does in fact result in a new mimeTypes file being generated, the new mimeTypes is just as barren as the old one had been. Based on the amount of unanswered Qs on the Googlesphere, I know this is a very common problem for Ubuntu users, but it seems to be one for which nobody has chimed in with a good solution. Maybe Superuser can finally be the panacea for us all?

  Read the article

• How do I configure IIS to allow access to network resources for PHP scripts?

  - by Dereleased

  I am currently working on a PHP front-end that joins together a series of applications running on separate servers; many of these applications generate files that I need access to, but these files (for various reasons) reside on their parent servers. If I, from the command line, issue a bit of script such as: <?php var_dump(glob("\\\\machine-name\\some\\share\\*")); I will get the full contents of that directory, proving that there's no problem programmatically with PHP reading the contents of a UNC share. However, if I try to execute the same script from the web server, I get an empty array -- more specifically, if I use more explicitly functions designed to "open" a directory like it was a file, I get access errors. I believe this to be a permissions issue, but I am not a server/network administrator type, so I'm not sure what I need to do to correct this and get my script running, and the links I've checked out have not been a terrible amount of help, perhaps due to my background, or lack thereof as far as IIS is concerned, coupled with the fact that we are not actually using .NET for this. Relevant Stats: Windows Server 2008 Standard SP2 IIS 7.0 PHP 5.2.9 I will be connecting to two types of servers: a few other nearly-identical Server 2008 machines, and a machine running embedded XP. Links that have not been particularly helpful but maybe I am just misreading: http://support.microsoft.com/?id=306158 http://support.microsoft.com/kb/207671/EN-US/ http://support.microsoft.com/kb/280383/

  Read the article

• server_name seems to be ignored in nginx

  - by user46171

  I have two domains set up in nginx.conf. Both are using SSL with their own certificates, and proxy to Apache. However the second domain is completely ignored, and nginx always resolves to the first domain. I can't see what in the issue is with this configuration, having set the server_name in each case correctly (as far as I can see): http { include mime.types; default_type application/octet-stream; keepalive_timeout 65; upstream site { # real IP addresses masked server xx.xxx.x.xxx; server xx.xxx.x.xxx; } server { # this domain always works listen 443; server_name *.first-site.com; ssl on; ssl_certificate /var/ssl/first-site.crt; ssl_certificate_key /var/ssl/first-site.key; location / { access_log off; proxy_connect_timeout 15; proxy_next_upstream error; proxy_pass http://site; proxy_set_header Host $http_host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-Protocol https; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_redirect off; } } server { # this domain is ignored, always resolves to first-site.com listen 443; server_name *.second-site.com; ssl on; ssl_certificate /var/ssl/second-site.crt; ssl_certificate_key /var/ssl/second-site.key; location / { access_log off; proxy_connect_timeout 15; proxy_next_upstream error; proxy_pass http://site; proxy_set_header Host $http_host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-Protocol https; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_redirect off; } } }

  Read the article

• Skipping nginx PHP cache for certain areas of a site?

  - by DisgruntledGoat

  I have just set up a new server with nginx (which I am new to) and PHP. On my site there are essentially 3 different types of files: static content like CSS, JS, and some images (most images are on an external CDN) main PHP/MySQL database-driven website which essentially acts like a static site dynamic PHP/MySQL forum It is my understanding from this question and this page that the static files need no special treatment and will be served as fast as possible. I followed the answer from the above question to set up caching for PHP files and now I have a config like this: location ~ \.php$ { try_files $uri =404; fastcgi_cache one; fastcgi_cache_key $scheme$host$request_uri; fastcgi_cache_valid 200 302 304 30m; fastcgi_cache_valid 301 1h; include /etc/nginx/fastcgi_params; fastcgi_pass unix:/var/run/php-fastcgi/php-fastcgi.socket; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME /srv/www/example$fastcgi_script_name; fastcgi_param HTTPS off; } However, now I want to prevent caching on the forum (either for everyone or only for logged-in users - haven't checked if the latter is feasible with the forum software). I've heard that "if is evil" inside location blocks, so I am unsure how to proceed. With the if inside the location block I would probably add this in the middle: if ($request_uri ~* "^/forum/") { fastcgi_cache_bypass 1; } # or possible this, if I'm able to cache pages for anonymous visitors if ($request_uri ~* "^/forum/" && $http_cookie ~* "loggedincookie") { fastcgi_cache_bypass 1; } Will that work fine, or is there a better way to achieve this?

  Read the article

• Deployment and monitoring tools for java/tomcat/linux environment

  - by Ran

  I'm a developer for many years, but don't have tons of experience in ops, so apology if this is a newbe question. In my company we run a web service written in Java mainly based on a Tomcat web server. We have two datacenters with about 10 hosts each. Hosts are of several types: Dababase, Tomcats, some offline java processes, memcached servers. All hosts are Linux CentOS Up until now, when releasing a new version to production we've been using a set of inhouse shell script that copy jars/wars and restart the tomcats. The company has gotten bigger so it has become more and more difficult operating all this and taking code from development, through QA, staging and to production. A typical release many times involves human errors that cost us precious uptime. Sometimes we need to revert to last known good and this isn't easy to say the least... We're looking for a tool, a framework, a solution that would provide the following: Supports the given list of technology (java, tomcat, linux etc) Provides easy deployment through different stages, including QA and production Provides configuration management. E.g. setting server properties (what's the connection URL of each host etc), server.xml or context configuration etc Monitoring. If we can get monitoring in the same package, that'll be nice. If not, then yet another tool we can use to monitor our servers. Preferably, open source with tons of documentation ;) Can anyone share their experience? Suggest a few tools? Thanks!

  Read the article

• What needs to be considered when setting up for Linux Development? [closed]

  - by user123586

  I want to set up a box for Linux development. I have a working linux install with the usual toolchain and an IDE. I'm looking for advice on how to approach structuring accounts and folders for development. As the Perl folks say "There's always more than one way to do it." Left to my own devices, I'll come up with several unproductive ways of doing it before figuring out what an experienced Linux programmer would think obvious. I'm not looking for instructions to follow for a specific set of tools or a specific software package. Instead, I'm looking for insight into what decisions need to be made and how to make them, with understanding of the advantages and disadvantages of each individual choice. These are some of the questions that come up: Where to put sources Where to put built object files and libraries where to install what to set in environment variables what compiler flags matter and how do you manage them across several types of builds what configuration entries to make in an IDE how to manage libraries to support multiple environments how to handle different build versions such as debug vs release, or cross platform builds If you are an experienced Linux developer, the answers to these questions may seem trivial and obvious. I'd like to learn to make decisions about these questions that result in as little manual configuration as possible, given some existing sources, a particular IDE, or no IDE at all, a paticular set of development libraries etc. At this point you're probably thinking: Can you be more specific? Sure. But remember that I'm trying to learn how to think about this stuff, not just follow a recipie for a specific set of results. Example: Setup a project that uses CMake for some of its components, autogen.sh followed by configure for others and just configure for a few more: debug builds without an IDE debug builds in NetBeans debug builds in Eclipse debug build in Visual Studio all of the above with release builds for Linux, Mac and Windows. So... **What are your thoughts on an approach that works for all four? Do you have any advice on what to read?**

  Read the article

• What are the advantages of registered memory?

  - by odd parity

  I'm browsing for a few low-end servers for a startup and I'm a bit confused about the different memory types. The advantage of ECC is clear - single-bit error correction. When it comes to registered memory it seems more vague, especially in systems that support both registered and unbuffered memory. A Google search mostly finds copies of the Wikipedia article, which states that registered memory chips "...place less electrical load on the memory controller and allow single systems to remain stable with more memory modules than they would have otherwise". However I can't find any quantification of this. What I'm wondering about is: Is registered memory an improvement over unbuffered when it comes to soft error rate, or is it purely about the maximum number of modules supported? If yes, at what point (amount of modules or GB of memory) do these improvements start to become noticeable? For a specific example, the HP ProLiant DL 120 G6 server manual states that maximum supported memory configuration is 16 GB unbuffered (4x4GB) or 12 GB registered (6x2GB). In this case I'd rather have the extra 4GB of memory if the reliability difference is negligible.

  Read the article

• Windows 7 pc freezes for an indeterminate amount of time after unlocking

  - by pikes

  Not sure if this type of question is appropriate for this forum, but I've tried everything I can think of to solve this problem aside from format/reinstall. I recently got a new work PC (Dell optiplex 755) with windows 7 professional x64. Standard developer software installed for .net development: VS2008, VS2005, SQL management studio, office 2007, etc. Recently I've been having this weird problem where after I lock my pc, when I try to unlock it, the screen will be black for awhile after unlocking. I can ctl+alt+del and put my password in but then it just goes black. The amount of time on the black screen seems to be related to the amount of time I am away from my PC. If only away a few minutes, it'll take about a minute to get to the desktop. If away for an hour, could take up to 15 minutes. If I lock it and go home for the night, I have to restart my PC in the morning (I've let it sit for an hour after a night of being locked and nothing happened). It doesn't do it every time but definitely the majority of the time. One weird thing I've seen is that if I remote into my machine before trying to log back in it does not do it. I uninstalled all software back to the point when I remember it started happening and it still does it. I was using this PC for a few weeks without this problem happening at all. Anyone know what my next troubleshooting steps could be? My IT department tried to fix it by moving my old profile to another disk and having me log in, effectively recreating a profile from scratch but that didn't solve it. As I said above if this isn't the right forum for these types of questions please let me know. Thanks in advance!

  Read the article

• Apache Virtual Host with directory aliases

  - by brechtvhb

  Hi, I'm trying to set up a dynamic virtual host in apache with a directory alias pointing to a difirent path for every domain. Here's what I'm trying to achive. Say I have 2 domains: * www.domain1.com * www.domein2.com I want both to point to the same index.php file (C:/cms/index.php). Now the hard part ... I want directories or certain file types to point to a diffirent path for each domain. Example: * www.domain1.com/layout -> C:/store/www.domain1.com/layout * www.domain2.com/layout -> C:/store/www.domain2.com/layout * www.domain1.com/image.png -> C:/store/www.domain1.com/image.png * www.domain2.com/image.png -> C:/store/www.domain2.com/image.png However the admin directory should point to the same path again for all sites * www.domain1.com/admin -> C:/cms/admin * www.domain2.com/admin -> C:/cms/admin Is there a way to achieve this kind of behaviour in apache 2.2 without having to create a virtualhost entry for each new domain?

  Read the article

• Config nginx for slow connection to avoide corrupted doanlowds

  - by user1850273

  We have a Windows 2003 server that nginx 1.3.8 is running. Our problem is users with slow connction about 10K . Our server is serving our program update files and when they download from our server the downloade file is incompleted or crrupted. (Users can not download file with DL manager and the problem is in IE ) for example in slow connection a file with 25mb , after 2Mb downloaded finish . in high speed connections there is no problem. Also when we redirect these slow connection to other port F.e 50005 with the same config they download will be much better but not good as other servers. Which config we must apply to avoide such these download stops or corrupted downloads in slow connection ? this is our server config : worker_processes 1; events { worker_connections 1024; } http { include mime.types; default_type application/octet-stream; log_format main '$remote_addr - $remote_user [$time_local] "$request" ' '$status $body_bytes_sent ' '"$http_user_agent"'; access_log logs/access.log main; sendfile off; keepalive_timeout 60; server { listen 80; server_name localhost; location / { root html; deny 127.0.0.3; index index.html index.htm; } } server_tokens off; } Our server use Htaccess password accounting and we can not use IIS on windows , Which soloution you think is better ? IIS with a extention to use apache htaccess ? Or use apache for windows insted of nginx ? Thank You.

  Read the article

< Previous Page | 247 248 249 250 251 252 253 254 255 256 257 258  | Next Page >