Search Results

Search found 16748 results on 670 pages for 'port block'.

Page 252/670 | < Previous Page | 248 249 250 251 252 253 254 255 256 257 258 259  | Next Page >

  • Application stuck in TCP retransmit

    - by SandeepJ
    I am running Linux kernel 3.13 (Ubuntu 14.04) on two Virtual Machines each of which operates inside two different servers running ESXi 5.1. There is a zeromq client-server application running between the two VMs. After running for about 10-30 minutes, this application consistently hangs due to inability to retransmit a lost packet. When I run the same setup over Ubuntu 12.04 (Linux 3.11), the application never fails If you notice below, "ss" (socket statistics) shows 1 packet lost, sk_wmem_queued of 14110 (i.e. w14110) and a high rto (120000). State Recv-Q Send-Q Local Address:Port Peer Address:Port ESTAB 0 12350 192.168.2.122:41808 192.168.2.172:55550 timer:(on,16sec,10) uid:1000 ino:35042 sk:ffff880035bcb100 <- skmem:(r0,rb648720,t0,tb1164800,f2274,w14110,o0,bl0) ts sack cubic wscale:7,7 rto:120000 rtt:7.5/3 ato:40 mss:8948 cwnd:1 ssthresh:21 send 9.5Mbps unacked:1 retrans:1/10 lost:1 rcv_rtt:1476 rcv_space:37621 Since this has happened so consistently, I was able to capture the TCP log in wireshark. I found that the packet which is lost does get retransmitted and even acknowledged by the TCP in the other OS (the sequence number is seen in the ACK), but the sender doesn't seem to understand this ACK and continues retransmitting. MTU is 9000 on both virtual machines and througout the route. The packets being sent are large in size. As I said earlier, this does not happen on Ubuntu 12.04 (kernel 3.11). So I did a diff on the TCP config options (seen via "sysctl -a |grep tcp ") between 14.04 and 12.04 and found the following differences. I also noticed that net.ipv4.tcp_mtu_probing=0 in both configurations. Left side is 3.11, right side is 3.13 <<net.ipv4.tcp_abc = 0 <<net.ipv4.tcp_cookie_size = 0 <<net.ipv4.tcp_dma_copybreak = 4096 14c11 << net.ipv4.tcp_early_retrans = 2 --- >> net.ipv4.tcp_early_retrans = 3 17c14 << net.ipv4.tcp_fastopen = 0 >> net.ipv4.tcp_fastopen = 1 20d16 << net.ipv4.tcp_frto_response = 0 26,27c22 << net.ipv4.tcp_max_orphans = 16384 << net.ipv4.tcp_max_ssthresh = 0 >> net.ipv4.tcp_max_orphans = 4096 29,30c24,25 << net.ipv4.tcp_max_tw_buckets = 16384 << net.ipv4.tcp_mem = 94377 125837 188754 >> net.ipv4.tcp_max_tw_buckets = 4096 >> net.ipv4.tcp_mem = 23352 31138 46704 34a30 >> net.ipv4.tcp_notsent_lowat = -1 My question to the networking experts on this forum : Are there any other debugging tools or options I can install/enable to dig further into why this TCP retransmit failure is occurring so consistently ? Are there any configuration changes which might account for this weird behaviour.

    Read the article

  • Sample code under MS-PL: must leave original comments?

    - by wtjones
    I have some files in my project that started from a sample in the all-in-one code sample browser: http://visualstudiogallery.msdn.microsoft.com/4934b087-e6cc-44dd-b992-a71f00a2a6df Some files contain boilerplate code that I modify heavily. They contain MS comments at the top that mention the license, copyright microsoft etc. Am I required to leave the entire comment block at the top of the source files that I modify or is it okay to just include the MS-PL license in a separate file for the whole project?

    Read the article

  • HTML5 + Quake II

    In case you missed it on the Google Web Toolkit Blog , check out this HTML5 port of Quake II. (Yep, that is a browser pushing 30 frames...

    Read the article

  • End of the Desktop? Google Backs WebGL

    <b>Linux Magazine:</b> "Stick a fork in the desktop, it's done! Recently Google demoed a port of Quake II to WebGL and HTML5, showing that even first person shooters are suitable applications to run in the browser."

    Read the article

  • How to run sunspots?

    - by user111317
    I am trying to use SUN Spots with Ubuntu, but for some reason the SUN Spot Manager app is not seeing connected spot on USB port. Possibility that cdc_acm driver is not installed has been mentioned elsewhere, but I am complete beginner when it comes to Ubuntu, so I don't know where to find it or how to install it. Any input on this matter would be more than welcome. Addition: ls /dev/tty* returned the list that contains /dev/ttyACM0, but SUN spot is still not recognizing it.

    Read the article

  • Is it possible (and practical) to search a string for arbitrary-length repeating patterns?

    - by blz
    I've recently developed a huge interest in cryptography, and I'm exploring some of the weaknesses of ECB-mode block ciphers. A common attack scenario involves encrypted cookies, whose fields can be represented as (relatively) short hex strings. Up until now, I've relied on my eyes to pick out repeating blocks, but this is rather tedious. I'm wondering what kind of algorithms (if any) could help me automate my search for repeating patterns within a string. Can anybody point me in the right direction?

    Read the article

  • My Ubuntu VPS was wiped

    - by Lucas806
    Someone gained access into my Ubuntu VPS via SSH, they entered rm -Rf / which wiped it and now I can't access it via SSH or SFTP. On SFTP I get the the following error: Error: Connection timed out Error: Could not connect to server And then on SSH, I try to connect to my VPS IP on Port 22, it doesn't come up with anything for ages (it should come up asking for a username) and then a op-up appears saying: Network Error: Connection timed out. Is it possible to fix this, if so, how?

    Read the article

  • Handling SQL Server Errors

    This article covers the basics of TRY CATCH error handling in T-SQL introduced in SQL Server 2005. It includes the usage of common functions to return information about the error and using the TRY CATCH block in stored procedures and transactions.

    Read the article

  • Joojoo Linux tablet video demo

    <b>V3.co.uk:</b> "V3.co.uk gets a walk through of the Joojoo tablet, which has a USB port and runs Linux underneath its browser interface. The 12.1-inch tablet has a capacitive touchscreen and features an Intel 1.6GHz Atom processor and Nvidia ION chipset."

    Read the article

  • Solaris Web Magazine JP ?????

    - by kazun
    #midashi{ font-size:120%; border-left: 8px solid #FF0000;/*??????????????????*/ border-bottom:dotted 1px #cccccc;/*?????????????*/ width:515px;/*??????*/ line-height: 26px;/*h3?????*/ padding-left: 5px;/*?????????*/ color:#333333; /*????*/ font-weight:bold; } .select{ padding-top:2px; padding-left: 3px;/*?????????*/ font-size:10px; color:#999999; display: block; } #midashi2{ font-size:120%; border-left: 8px solid #FF0000;/*??????????????????*/ border-bottom:dotted 1px #cccccc;/*?????????????*/ width:205px;/*??????*/ line-height: 26px;/*h3?????*/ padding-left: 5px;/*?????????*/ color:#333333; /*????*/ font-weight:bold; } .select{ padding-top:2px; padding-left: 3px;/*?????????*/ font-size:10px; color:#999999; display: block; } ???? ????????:Oracle OpenWorld Tokyo 2012 ?????? ????:?????????????????:???????Oracle Solaris Studio 12.3? ???? Oracle Solaris ???????????????????? Oracle OpenWorld Tokyo 2012 ?????? Oracle Solaris 11 ?????????:?Oracle Solaris 11 ?????·????·??? ?2???? ?????????????????:???????Oracle Solaris Studio 12.3? ????? ???? ??????????????????????? Oracle Solaris Oracle Solaris Studio Oracle Solaris Cluster ????? ???? Oracle Technology Network ??????????????????????????????? Oracle Solaris 11 Oracle Solaris 10 Oracle Solaris Cluster Enterprise Edition Oracle Solaris Studio OTN? ????/????  ?????????#4?6/15(?)??? 2012/5/21 Oracle Solaris ??????? #3 2012/5/23 ?83? ????! ???????? ~Oracle x Sun ?6?: Solaris 10 ?? Solaris 11 ?????????????(Slideshare) ?????? Solaris 11 Solaris 10 Oracle Solaris Cluster Oracle Solaris Studio Oracle Linux OTN? ??????????? ?????????? Oracle Solaris ????????????????????????????????????????????????? ???????????????????????????????????????????????? OTN ???? ?????? ????? ?????? ???? Oracle Software Delivery Cloud My Oracle Support ????????? Oracle PartnerNetwork Oracle Solaris Knowledge Zone ????????? Solaris ?????? Oracle|Sun ????????? Oracle Japan (??????) Oracle University ????? Oracle Solaris 11 ?????? Oracle Solaris 11 ??????????? Sun Cluster for Hign Availability ???????? ???????? ?????????? Server / Storage System ????

    Read the article

  • Optimizing Robots Text File

    We can block spiders to crawl restricted parts of our website. Restricted parts of our website means those links of our website which we don't want to be indexed in search engines and getting some unwanted visitors. For example:

    Read the article

  • Stairway to SQL Dialects Level 3: MySQL

    As part of the LAMP stack, MySQL is incredibly important for providing a reliable and platform-agnostic database platform for web development. This level looks at the syntax of MySQL and how to best port SQL code to a MySQL environment. NEW! The easiest way to deploy .NET codeDeploy ASP.NET applications fast, frequently, and without fuss, using Deployment Manager, the new tool from Red Gate. Try it now.

    Read the article

  • where is this function getting its values from

    - by user295189
    I have the JS file below that I am working on and I have a need to know this specific function pg.getRecord_Response = function(){ } within the file. I need to know where are the values are coming from in this function for example arguments[0].responseText? I am new to javascript so any help will be much appreciated. Thanks var pg = new Object(); var da = document.body.all; // ===== - EXPRESS BUILD [REQUEST] - ===== // pg.expressBuild_Request = function(){ var n = new Object(); n.patientID = request.patientID; n.encounterID = request.encounterID; n.flowSheetID = request.flowSheetID; n.encounterPlan = request.encounterPlan; n.action = "/location/diagnosis/dsp_expressBuild.php"; n.target = popWinCenterScreen("/common/html/empty.htm", 619, 757, ""); myLocationDB.PostRequest(n); } // ===== - EXPRESS BUILD [RESPONSE] - ===== // pg.expressBuild_Response = function(){ pg.records.showHiddenRecords = 0; pg.loadRecords_Request(arguments.length ? arguments[0] : 0); } // ===== - GET RECORD [REQUEST] - ===== // pg.getRecord_Request = function(){ if(pg.records.lastSelected){ pg.workin(true); pg.record.recordID = pg.records.lastSelected.i; var n = new Object(); n.noheaders = 1; n.recordID = pg.record.recordID; myLocationDB.Ajax.Post("/location/diagnosis/get_record.php", n, pg.getRecord_Response); } else { pg.buttons.btnOpen.disable(true); } } // ===== - GET RECORD [RESPONSE] - ===== // pg.getRecord_Response = function(){ //alert(arguments[0].responseText); if(arguments.length && arguments[0].responseText){ alert(arguments[0].responseText); // Refresh PQRI grid when encounter context if(request.encounterID && window.parent.frames['main']){ window.parent.frames['main'].pg.loadQualityMeasureRequest(); } var rec = arguments[0].responseText.split(pg.delim + pg.delim); if(rec.length == 20){ // validate record values rec[0] = parseInt(rec[0]); rec[3] = parseInt(rec[3]); rec[5] = parseInt(rec[5]); rec[6] = parseInt(rec[6]); rec[7] = parseInt(rec[7]); rec[8] = parseInt(rec[8]); rec[9] = parseInt(rec[9]); rec[10] = parseInt(rec[10]); rec[11] = parseInt(rec[11]); rec[12] = parseInt(rec[12]); rec[15] = parseInt(rec[15]); // set record state pg.recordState = { recordID: pg.record.recordID, codeID: rec[0], description: rec[2], assessmentTypeID: rec[3], type: rec[4], onsetDateYear: rec[5], onsetDateMonth: rec[6], onsetDateDay: rec[7], onsetDateIsApproximate: rec[8], resolveDateYear: rec[9], resolveDateMonth: rec[10], resolveDateDay: rec[11], resolveDateIsApproximate: rec[12], commentsCount: rec[15], comments: rec[16] } // set record view pg.record.code.codeID = pg.recordState.codeID; pg.record.code.value = rec[1]; pg.record.description.value = rec[2]; for(var i=0; i<pg.record.type.options.length; i++){ if(pg.record.type.options[i].value == rec[4]){ pg.record.type.selectedIndex = i; break; } } for(var i=0; i<pg.record.assessmentType.options.length; i++){ if(pg.record.assessmentType.options[i].value == rec[3]){ pg.record.assessmentType.selectedIndex = i; break; } } if(rec[5]){ if(rec[6] && rec[7]){ pg.record.onsetDateType.selectedIndex = 0; pg.record.onsetDate.value = rec[6] + "/" + rec[7] + "/" + rec[5]; pg.record.onsetDate.format(); } else { pg.record.onsetDateType.selectedIndex = 1; pg.record.onsetDateMonth.selectedIndex = rec[6]; for(var i=0; i<pg.record.onsetDateYear.options.length; i++){ if(pg.record.onsetDateYear.options[i].value == rec[5]){ pg.record.onsetDateYear.selectedIndex = i; break; } } if(rec[8]) pg.record.chkOnsetDateIsApproximate.checked = true; } } else { pg.record.onsetDateType.selectedIndex = 2; } if(rec[9]){ if(rec[10] && rec[11]){ pg.record.resolveDateType.selectedIndex = 0; pg.record.resolveDate.value = rec[10] + "/" + rec[11] + "/" + rec[9]; pg.record.resolveDate.format(); } else { pg.record.resolveDateType.selectedIndex = 1; pg.record.resolveDateMonth.selectedIndex = rec[10]; for(var i=0; i<pg.record.resolveDateYear.options[i].length; i++){ if(pg.record.resolveDateYear.options.value == rec[9]){ pg.record.resolveDateYear.selectedIndex = i; break; } } if(rec[12]) pg.record.chkResolveDateIsApproximate.checked = true; } } else { pg.record.resolveDateType.selectedIndex = 2; } pg.record.lblCommentCount.innerHTML = rec[15]; pg.record.comments.value = rec[16]; pg.record.lblUpdatedBy.innerHTML = "* Last updated by " + rec[13] + " on " + rec[14]; pg.record.lblUpdatedBy.title = "Updated by: " + rec[13] + "\nUpdated on: " + rec[14]; pg.record.linkedNotes.setData(rec[18]); pg.record.linkedOrders.setData(rec[19]); pg.record.updates.setData(rec[17]); return; } } alert("An error occured while attempting to retrieve\ndetails for record #" + pg.record.recordID + ".\n\nPlease contact support if this problem persists.\nWe apologize for the inconvenience."); pg.hideRecordView(); } // ===== - HIDE COMMENTS VIEW - ===== // pg.hideCommentsView = function(){ pg.recordComments.style.left = ""; pg.recordComments.disabled = true; pg.recordComments.comments.value = ""; pg.record.disabled = false; pg.record.style.zIndex = 5500; } // ===== - HIDE code SEARCH - ===== // pg.hidecodeSearch = function(){ pg.codeSearch.style.left = ""; pg.codeSearch.disabled = true; pg.record.disabled = false; pg.record.style.zIndex = 5500; } // ===== - HIDE RECORD - ===== // pg.hideRecord = function(){ if(arguments.length){ pg.loadRecords_Request(); } else if(pg.records.lastSelected){ var n = new Object(); n.recordTypeID = 11; n.patientID = request.patientID; n.recordID = pg.records.lastSelected.i; n.action = "/location/hideRecord/dsp_hideRecord.php"; n.target = popWinCenterScreen("/common/html/empty.htm", 164, 476); myLocationDB.PostRequest(n); } } // ===== - HIDE RECORD VIEW - ===== // pg.hideRecordView = function(){ pg.record.style.left = ""; pg.record.disabled = true; // reset record grids pg.record.updates.state = "NO_RECORDS"; pg.record.linkedNotes.state = "NO_RECORDS"; pg.record.linkedOrders.state = "NO_RECORDS"; // reset linked record tabs pg.record.tabs[0].click(); pg.record.tabs[1].disable(true); pg.record.tabs[2].disable(true); pg.record.tabs[1].all[1].innerHTML = "Notes"; pg.record.tabs[2].all[1].innerHTML = "Orders"; // reset record state pg.recordState = null; // reset record view pg.record.recordID = 0; pg.record.code.value = ""; pg.record.code.codeID = 0; pg.record.description.value = ""; pg.record.type.selectedIndex = 0; pg.record.assessmentType.selectedIndex = 0; pg.record.onsetDateType.selectedIndex = 0; pg.record.chkOnsetDateIsApproximate.checked = false; pg.record.resolveDateType.selectedIndex = 0; pg.record.chkResolveDateIsApproximate.checked = false; pg.record.lblCommentCount.innerHTML = 0; pg.record.comments.value = ""; pg.record.lblUpdatedBy.innerHTML = ""; pg.record.lblUpdatedBy.title = ""; pg.record.updateComment = ""; pg.recordComments.comments.value = ""; pg.record.active = false; pg.codeSearch.newRecord = true; pg.blocker.className = ""; pg.workin(false); } // ===== - HIDE UPDATE VIEW - ===== // pg.hideUpdateView = function(){ pg.recordUpdate.style.left = ""; pg.recordUpdate.disabled = true; pg.recordUpdate.type.value = ""; pg.recordUpdate.onsetDate.value = ""; pg.recordUpdate.description.value = ""; pg.recordUpdate.resolveDate.value = ""; pg.recordUpdate.assessmentType.value = ""; pg.record.disabled = false; pg.record.btnViewUpdate.setState(); pg.record.style.zIndex = 5500; } // ===== - INIT - ===== // pg.init = function(){ var tab = 1; pg.delim = String.fromCharCode(127); pg.subDelim = String.fromCharCode(1); pg.blocker = da.blocker; pg.hourglass = da.hourglass; pg.pageContent = da.pageContent; pg.blocker.shim = da.blocker_shim; pg.activeTip = da.activeTip; pg.activeTip.anchor = null; pg.activeTip.shim = da.activeTip_shim; // PAGE TITLE pg.pageTitle = da.pageTitle; // TOTAL RECORDS pg.totalRecords = da.totalRecords[0]; // START RECORD pg.startRecord = da.startRecord[0]; pg.startRecord.onchange = function(){ pg.records.startRecord = this.value; pg.loadRecords_Request(); } // RECORD PANEL pg.recordPanel = myLocationDB.RecordPanel(pg.pageContent.all.recordPanel); for(var i=0; i<pg.recordPanel.buttons.length; i++){ if(pg.recordPanel.buttons[i].orderBy){ pg.recordPanel.buttons[i].onclick = pg.sortRecords; } } // RECORDS GRIDVIEW pg.records = pg.recordPanel.all.grid; alert(pg.recordPanel.all.grid); pg.records.sortOrder = "DESC"; pg.records.lastExpanded = null; pg.records.attachEvent("onrowclick", pg.record_click); pg.records.orderBy = pg.recordPanel.buttons[0].orderBy; pg.records.attachEvent("onrowmouseout", pg.record_mouseOut); pg.records.attachEvent("onrowdblclick", pg.getRecord_Request); pg.records.attachEvent("onrowmouseover", pg.record_mouseOver); pg.records.attachEvent("onstateready", pg.loadRecords_Response); // BUTTON - TOGGLE HIDDEN RECORDS pg.btnHiddenRecords = myLocationDB.Custom.ImageButton(3, 751, 19, 19, "/common/images/hide.gif", 1, 1, "", "", da.pageContent); pg.btnHiddenRecords.setTitle("Show hidden records"); pg.btnHiddenRecords.onclick = pg.toggleHiddenRecords; pg.btnHiddenRecords.setState = function(){ this.disable(!pg.records.totalHiddenRecords); } // code SEARCH SUBWIN pg.codeSearch = da.subWin_codeSearch; pg.codeSearch.newRecord = true; pg.codeSearch.searchType = "code"; pg.codeSearch.searchFavorites = true; pg.codeSearch.onkeydown = function(){ if(window.event && window.event.keyCode && window.event.keyCode == 113){ if(pg.codeSearch.searchType == "DESCRIPTION"){ pg.codeSearch.searchType = "code"; pg.codeSearch.lblSearchType.innerHTML = "ICD-9 Code"; } else { pg.codeSearch.searchType = "DESCRIPTION"; pg.codeSearch.lblSearchType.innerHTML = "Description"; } pg.searchcodes_Request(); } } // SEARCH TYPE pg.codeSearch.lblSearchType = pg.codeSearch.all.lblSearchType; // SEARCH STRING pg.codeSearch.searchString = pg.codeSearch.all.searchString; pg.codeSearch.searchString.tabIndex = 1; pg.codeSearch.searchString.onfocus = function(){ this.select(); } pg.codeSearch.searchString.onblur = function(){ this.value = this.value.trim(); } pg.codeSearch.searchString.onkeydown = function(){ if(window.event && window.event.keyCode && window.event.keyCode == 13){ pg.searchcodes_Request(); } } // -- "SEARCH" pg.codeSearch.btnSearch = pg.codeSearch.all.btnSearch; pg.codeSearch.btnSearch.tabIndex = 2; pg.codeSearch.btnSearch.disable = myLocationDB.Disable; pg.codeSearch.btnSearch.onclick = pg.searchcodes_Request; pg.codeSearch.btnSearch.baseTitle = "Search diagnosis codes"; pg.codeSearch.btnSearch.setState = function(){ pg.codeSearch.btnSearch.disable(pg.codeSearch.searchString.value.trim().length < 2); } pg.codeSearch.searchString.onkeyup = pg.codeSearch.btnSearch.setState; // START RECORD / TOTAL RECORDS pg.codeSearch.startRecord = pg.codeSearch.all.startRecord; pg.codeSearch.totalRecords = pg.codeSearch.all.totalRecords; pg.codeSearch.startRecord.onchange = function(){ pg.codeSearch.records.startRecord = this.value; pg.searchcodes_Request(); } // RECORD PANEL pg.codeSearch.recordPanel = myLocationDB.RecordPanel(pg.codeSearch.all.recordPanel); pg.codeSearch.recordPanel.buttons[0].onclick = pg.sortcodeResults; pg.codeSearch.recordPanel.buttons[1].onclick = pg.sortcodeResults; // DATA GRIDVIEW pg.codeSearch.records = pg.codeSearch.all.grid; pg.codeSearch.records.orderBy = "code"; pg.codeSearch.records.attachEvent("onrowdblclick", pg.updatecode); pg.codeSearch.records.attachEvent("onstateready", pg.searchcodes_Response); // BUTTON - "CANCEL" pg.codeSearch.btnCancel = pg.codeSearch.all.btnCancel; pg.codeSearch.btnCancel.tabIndex = 4; pg.codeSearch.btnCancel.onclick = pg.hidecodeSearch; pg.codeSearch.btnCancel.title = "Close this search area"; // SEARCH FAVORITES / ALL pg.codeSearch.optSearch = myLocationDB.InputButton(pg.codeSearch.all.optSearch); pg.codeSearch.optSearch[0].onclick = function(){ if(pg.codeSearch.searchFavorites){ pg.codeSearch.searchString.focus(); } else { pg.codeSearch.searchFavorites = true; pg.searchcodes_Request(); } } pg.codeSearch.optSearch[1].onclick = function(){ if(pg.codeSearch.searchFavorites){ pg.codeSearch.searchFavorites = false; pg.searchcodes_Request(); } else { pg.codeSearch.searchString.focus(); } } // -- "USE SELECTED" pg.codeSearch.btnUseSelected = pg.codeSearch.all.btnUseSelected; pg.codeSearch.btnUseSelected.tabIndex = 3; pg.codeSearch.btnUseSelected.onclick = pg.updatecode; pg.codeSearch.btnUseSelected.disable = myLocationDB.Disable; pg.codeSearch.btnUseSelected.baseTitle = "Use the selected diagnosis code"; pg.codeSearch.btnUseSelected.setState = function(){ pg.codeSearch.btnUseSelected.disable(!pg.codeSearch.records.lastSelected); } pg.codeSearch.records.attachEvent("onrowclick", pg.codeSearch.btnUseSelected.setState); // RECORD STATE pg.recordState = null; // RECORD SUBWIN pg.record = da.subWin_record; pg.record.recordID = 0; pg.record.active = false; pg.record.updateComment = ""; // -- TABS pg.record.tabs = myLocationDB.TabCollection( pg.record.all.tab, function(){ if(pg.record.tabs[0].all[0].checked){ pg.record.btnOpen.style.display = "none"; pg.record.chkSelectAll.hitArea.style.display = "none"; pg.record.btnSave.style.display = "block"; pg.record.lblUpdatedBy.style.display = "block"; pg.record.pnlRecord_shim.style.display = "none"; } else { pg.record.pnlRecord_shim.style.display = "block"; pg.record.btnSave.style.display = "none"; pg.record.lblUpdatedBy.style.display = "none"; pg.record.btnOpen.setState(); pg.record.btnOpen.style.display = "block"; if(pg.record.tabs[2].all[0].checked){ pg.record.chkSelectAll.hitArea.style.display = "none"; //pg.record.btnViewLabs.setState(); //pg.record.btnViewLabs.style.display = "block"; } else { pg.record.chkSelectAll.setState(); pg.record.chkSelectAll.hitArea.style.display = "block"; //pg.record.btnViewLabs.style.display = "none"; } } } ); pg.record.tabs[1].disable(true); pg.record.tabs[2].disable(true); pg.record.pnlRecord_shim = pg.record.all.pnlRecord_shim; pg.record.code = pg.record.all.code; pg.record.code.codeID = 0; pg.record.code.tabIndex = -1; // -- CHANGE code pg.record.btnChangecode = myLocationDB.Custom.ImageButton(6, 107, 22, 22, "/common/images/edit.gif", 2, 2, "", "", pg.record.all.pnlRecord); pg.record.btnChangecode.tabIndex = 1; pg.record.btnChangecode.onclick = pg.showcodeSearch; pg.record.btnChangecode.title = "Change the diagnosis code for this problem"; pg.record.description = pg.record.all.description; pg.record.description.tabIndex = 2; pg.record.type = pg.record.all.type; pg.record.type.tabIndex = 3; pg.record.assessmentType = pg.record.all.assessmentType; pg.record.assessmentType.tabIndex = 9; // ONSET DATE pg.record.onsetDateType = pg.record.all.onsetDateType; pg.record.onsetDateType.tabIndex = 4; pg.record.onsetDateType.onchange = pg.record.onsetDateType.setState = function(){ switch(this.selectedIndex){ case 1: // PARTIAL pg.record.chkOnsetDateIsApproximate.disable(false); pg.record.onsetDate.style.visibility = "hidden"; pg.record.onsetDateUnknown.style.visibility = "hidden"; pg.record.onsetDate.datePicker.style.visibility = "hidden"; pg.record.onsetDateMonth.style.visibility = "visible"; pg.record.onsetDateYear.style.visibility = "visible"; break; case 2: // UNKNOWN pg.record.chkOnsetDateIsApproximate.disable(true); pg.record.onsetDate.style.visibility = "hidden"; pg.record.onsetDateYear.style.visibility = "hidden"; pg.record.onsetDateMonth.style.visibility = "hidden"; pg.record.onsetDate.datePicker.style.visibility = "hidden"; pg.record.onsetDateUnknown.style.visibility = "visible"; break; default: // "WHOLE" pg.record.chkOnsetDateIsApproximate.disable(true); pg.record.onsetDateMonth.style.visibility = "hidden"; pg.record.onsetDateYear.style.visibility = "hidden"; pg.record.onsetDateUnknown.style.visibility = "hidden"; pg.record.onsetDate.style.visibility = "visible"; pg.record.onsetDate.datePicker.style.visibility = "visible"; break; } } pg.record.onsetDate = myLocationDB.Custom.DateInput(30, 364, 80, pg.record.all.pnlRecord, 1, 1, 0, params.todayDate, 1); pg.record.onsetDate.tabIndex = 5; pg.record.onsetDate.style.textAlign = "LEFT"; pg.record.onsetDate.calendar.style.zIndex = 6000; pg.record.onsetDate.datePicker.style.left = "448px"; pg.record.onsetDate.setDateRange(params.birthDate, params.todayDate); pg.record.onsetDateYear = pg.record.all.onsetDateYear; pg.record.onsetDateYear.tabIndex = 6; pg.record.onsetDateMonth = pg.record.all.onsetDateMonth pg.record.onsetDateMonth.tabIndex = 7; pg.record.onsetDateUnknown = pg.record.all.onsetDateUnknown; pg.record.onsetDateUnknown.tabIndex = 8; pg.record.chkOnsetDateIsApproximate = myLocationDB.InputButton(pg.record.all.chkOnsetDateIsApproximate); pg.record.chkOnsetDateIsApproximate.setTitle("Onset date is approximate"); pg.record.chkOnsetDateIsApproximate.disable(true); // RESOLVE DATE pg.record.lblResolveDate = pg.record.all.lblResolveDate; pg.record.resolveDateType = pg.record.all.resolveDateType; pg.record.resolveDateType.tabIndex = 10; pg.record.resolveDateType.lastSelectedIndex = 0; pg.record.resolveDateType.setState = function(){ switch(this.selectedIndex){ case 1: // PARTIAL pg.record.chkResolveDateIsApproximate.disable(false); pg.record.resolveDate.style.visibility = "hidden"; pg.record.resolveDateUnknown.style.visibility = "hidden"; pg.record.resolveDate.datePicker.style.visibility = "hidden"; pg.record.resolveDateMonth.style.visibility = "visible"; pg.record.resolveDateYear.style.visibility = "visible"; break; case 2: // UNKNOWN pg.record.chkResolveDateIsApproximate.disable(true); pg.record.resolveDate.style.visibility = "hidden"; pg.record.resolveDateYear.style.visibility = "hidden"; pg.record.resolveDateMonth.style.visibility = "hidden"; pg.record.resolveDate.datePicker.style.visibility = "hidden"; pg.record.resolveDateUnknown.style.visibility = "visible"; break; default: // "WHOLE" pg.record.chkResolveDateIsApproximate.disable(true); pg.record.resolveDateMonth.style.visibility = "hidden"; pg.record.resolveDateYear.style.visibility = "hidden"; pg.record.resolveDateUnknown.style.visibility = "hidden"; pg.record.resolveDate.style.visibility = "visible"; pg.record.resolveDate.datePicker.style.visibility = "visible"; break; } } pg.record.resolveDateType.onchange = function(){ this.lastSelectedIndex = this.selectedIndex; this.setState(); } pg.record.resolveDate = myLocationDB.Custom.DateInput(55, 364, 80, pg.record.all.pnlRecord, 1, 1, 0, params.todayDate, 1); pg.record.resolveDate.tabIndex = 11; pg.record.resolveDate.style.textAlign = "LEFT"; pg.record.resolveDate.calendar.style.zIndex = 6000; pg.record.resolveDate.datePicker.style.left = "448px"; pg.record.resolveDate.setDateRange(params.birthDate, params.todayDate); pg.record.resolveDate.setState = function(){ if(pg.record.assessmentType.value == 15){ pg.record.chkResolveDateIsApproximate.disable(pg.record.resolveDateType.value != "PARTIAL"); pg.record.resolveDate.disabled = false; pg.record.lblResolveDate.disabled = false; pg.record.resolveDateType.selectedIndex = pg.record.resolveDateType.lastSelectedIndex; pg.record.resolveDateType.setState(); pg.record.resolveDate.datePicker.disable(false); pg.record.resolveDateType.disabled = false; pg.record.resolveDateYear.disabled = false; pg.record.resolveDateMonth.disabled = false; pg.record.resolveDateUnknown.disabled = false; } else { pg.record.resolveDate.datePicker.disable(true); pg.record.chkResolveDateIsApproximate.disable(true); pg.record.resolveDateType.selectedIndex = 2; pg.record.resolveDateType.setState(); pg.record.resolveDate.disabled = true; pg.record.lblResolveDate.disabled = true; pg.record.resolveDateType.disabled = true; pg.record.resolveDateYear.disabled = true; pg.record.resolveDateMonth.disabled = true; pg.record.resolveDateUnknown.disabled = true; } } pg.record.assessmentType.onchange = pg.record.resolveDate.setState; pg.record.resolveDateYear = pg.record.all.resolveDateYear; pg.record.resolveDateYear.tabIndex = 11; pg.record.resolveDateMonth = pg.record.all.resolveDateMonth pg.record.resolveDateMonth.tabIndex = 12; pg.record.resolveDateUnknown = pg.record.all.resolveDateUnknown; pg.record.resolveDateUnknown.tabIndex = 13; pg.record.chkResolveDateIsApproximate = myLocationDB.InputButton(pg.record.all.chkResolveDateIsApproximate); pg.record.chkResolveDateIsApproximate.setTitle("Resolve date is approximate"); pg.record.chkResolveDateIsApproximate.disable(true); // -- UPDATES pg.record.updates = pg.record.all.pnlUpdates.all.grid; pg.record.lblUpdateCount = pg.record.all.lblUpdateCount; pg.record.updates.attachEvent("onstateready", pg.showRecordView); pg.record.updates.attachEvent("onrowdblclick", pg.showUpdateView); // -- "VIEW SELECTED" pg.record.btnViewUpdate = myLocationDB.PanelButton(pg.record.all.btnViewUpdate); pg.record.btnViewUpdate.setTitle("View details for the selected problem update"); pg.record.btnViewUpdate.onclick = pg.showUpdateView; pg.record.btnViewUpdate.setState = function(){ pg.record.btnViewUpdate.disable(!pg.record.updates.lastSelected); } pg.record.updates.attachEvent("onrowclick", pg.record.btnViewUpdate.setState); // -- COMMENTS pg.record.comments = pg.record.all.comments; pg.record.pnlComments = pg.record.all.pnlComments; pg.record.lblCommentCount = pg.record.all.lblCommentCount; // -- UPDATE COMMENTS pg.record.btnUpdateComments = myLocationDB.PanelButton(pg.record.all.btnUpdateComments); pg.record.btnUpdateComments.onclick = pg.showCommentView; pg.record.btnUpdateComments.title = "Update this record's comments"; // -- LINKED NOTES pg.record.linkedNotes = pg.record.all.linkedNotes.all.grid; pg.record.linkedNotes.attachEvent("onrowclick", pg.linkedRecordClick); pg.record.linkedNotes.attachEvent("onrowdblclick", pg.openLinkedNote); pg.record.linkedNotes.attachEvent("onstateready", pg.setLinkedNotes_Count); // -- LINKED ORDERS pg.record.linkedOrders = pg.record.all.linkedOrders.all.grid; pg.record.linkedOrders.attachEvent("onrowclick", pg.linkedRecordClick); pg.record.linkedOrders.attachEvent("onrowdblclick", pg.openLinkedOrder); pg.record.linkedOrders.attachEvent("onstateready", pg.setLinkedOrders_Count); // -- "CLOSE" pg.record.btnClose = pg.record.all.btnClose; pg.record.btnClose.tabIndex = 15; pg.record.btnClose.onclick = pg.hideRecordView; pg.record.btnClose.title = "Close this record panel"; // -- LAST UPDATED BY pg.record.lblUpdatedBy = pg.record.all.lblUpdatedBy; // -- "SELECT ALL" pg.record.chkSelectAll = myLocationDB.InputButton(pg.record.all.chkSelectAll); pg.record.chkSelectAll.onclick = function(){ if(pg.record.tabs[1].all[0].checked){ if(pg.record.chkSelectAll.checked){ pg.record.linkedNotes.selectAll(); } else { pg.record.linkedNotes.deselectAll(); } } else { if(pg.record.chkSelectAll.checked){ pg.record.linkedOrders.selectAll(); } else { pg.record.linkedOrders.deselectAll(); } } pg.record.btnOpen.setState(); //pg.record.btnViewLabs.setState(); } pg.record.chkSelectAll.setState = function(){ if(pg.record.tabs[1].all[0].checked){ pg.record.chkSelectAll.checked = pg.record.linkedNotes.selectedRows.length == pg.record.linkedNotes.rows.length; } else { pg.record.chkSelectAll.checked = pg.record.linkedOrders.selectedRows.length == pg.record.linkedOrders.rows.length; } } // -- "OPEN SELECTED" pg.record.btnOpen = pg.record.all.btnOpenSelected; pg.record.btnOpen.tabIndex = 14; pg.record.btnOpen.disable = myLocationDB.Disable; pg.record.btnOpen.title = "Open the selected record"; pg.record.btnOpen.onclick = function(){ if(pg.record.tabs[1].all[0].checked){ pg.openLinkedNote(); } else if(pg.record.tabs[2].all[0].checked){ pg.openLinkedOrder(); } else { pg.record.btnOpen.disable(true); } } pg.record.btnOpen.setState = function(){ if(pg.record.tabs[1].all[0].checked){ pg.record.btnOpen.disable(!pg.record.linkedNotes.lastSelected); } else if(pg.record.tabs[2].all[0].checked){ pg.record.btnOpen.disable(pg.record.linkedOrders.selectedRows.length != 1); } else { pg.record.btnOpen.disable(true); } } // -- "SAVE" pg.record.btnSave = pg.record.all.btnSave; pg.record.btnSave.tabIndex = 14; pg.record.btnSave.onclick = pg.updateRecord_Request; pg.record.btnSave.title = "Save changes to this record"; // RECORD UPDATE SUBWIN pg.recordUpdate = da.subWin_update; pg.recordUpdate.lblUpdatedBy = pg.recordUpdate.all.lblUpdatedBy; pg.recordUpdate.lblUpdateDTS = pg.recordUpdate.all.lblUpdateDTS; pg.recordUpdate.type = pg.recordUpdate.all.type; pg.recordUpdate.onsetDate = pg.recordUpdate.all.onsetDate; pg.recordUpdate.description = pg.recordUpdate.all.description; pg.recordUpdate.resolveDate = pg.recordUpdate.all.resolveDate; pg.recordUpdate.assessmentType = pg.recordUpdate.all.assessmentType; // -- "CLOSE" pg.recordUpdate.btnClose = pg.recordUpdate.all.btnClose; pg.recordUpdate.btnClose.tabIndex = 1; pg.recordUpdate.btnClose.onclick = pg.hideUpdateView; pg.recordUpdate.btnClose.title = "Close this sub-window"; // COMMENTS SUBWIN pg.recordComments = da.subWin_comments; pg.recordComments.comments = pg.recordComments.all.updateComments; pg.recordComments.comment

    Read the article

  • FTP through HAProxy

    - by Menda
    I have a machine, which is the Host and has HAProxy installed in it and working. Then I have a Guest KVM virtual machine running inside the Host with an IP 192.168.122.152. I installed an FTP server in the Guest machine with VSFTPD. From the Host, if I try the command $ ftp -p 192.168.122.152, works perfectly and I can connect to the Guest FTP. I need to remark that this FTP is configured as passive, but both passive and active connections are working from the Host. This is an extract of part of /etc/vsftpd.conf in the Guest: # Passive mode connect_from_port_20=NO tcp_wrappers=YES listen_address=192.168.122.152 pasv_enable=YES pasv_promiscuous=NO port_enable=YES port_promiscuous=NO pasv_max_port=10000 pasv_min_port=10250 Now it's time to make it accessible from outside, so I configure /etc/haproxy/haproxy.cfg like this: listen FTP_Default *:21 server ftp01 192.168.122.152 check port 21 inter 10s rise 1 fall 2 listen FTP_Range *:10000-10250 server ftp01 192.168.122.152 check port 21 inter 10s rise 1 fall 2 But if I try to connect from other machine in internet $ ftp -p $PUBLICIP, it only responds: Connected to <PUBLICIP>, but it doesn't ask for the login and password. Something in the HAProxy config must be wrong, because it's the only point where it fails. By the way, I tried to adapt my configuration to this one in this blog. Thanks.

    Read the article

  • MobaXTerm - SSH Key authentication

    - by Chip Sprague
    I have a key that I converted and works fine with Putty. I have tried these formats: ssh -p 1111 -i id_rsa [email protected] ssh -i id_rsa -p 1111 [email protected] The key is in the same folder as the MobaXTerm executable. Thanks! EDIT: [chip.client] $ ssh -p 1111 -i id_rsa [email protected] -v Warning: Identity file id_rsa not accessible: No such file or directory. OpenSSH_5.6p1, OpenSSL 0.9.8r 8 Feb 2011 debug1: Reading configuration data /etc/ssh_config debug1: Connecting to 192.168.0.9 [192.168.0.100] port 1111. debug1: Connection established. debug1: identity file /home/chip/.ssh/id_rsa type -1 debug1: identity file /home/chip/.ssh/id_rsa-cert type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.3p1 Debian-3ubuntu7 debug1: match: OpenSSH_5.3p1 Debian-3ubuntu7 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.6 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-ctr hmac-md5 [email protected] debug1: kex: client->server aes128-ctr hmac-md5 [email protected] debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: checking without port identifier Warning: Permanently added '[192.168.0.100]:1111' (RSA) to the list of known hosts. debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: Roaming not allowed by server debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey debug1: Next authentication method: publickey debug1: Trying private key: /home/chip/.ssh/id_rsa debug1: No more authentication methods to try. Permission denied (publickey). [01/09/2011 - 09:15.38] ~

    Read the article

  • MailEnable - Configuring TLS for secure SMTP (Gmail)

    - by Buckers
    I have the latest version of MailEnable Pro installed on a new server that I'm setting up. Sending & receiving works fine with a new email account that I have set up, however I am now trying to configure GMail to use the mailserver for outgoing SMTP. I've done the following so far: Creating a self-cert SSL certficiate Ticked "Enable TLS" on the General tab of the SMTP connector properties Ticked "Send using TLS if remote server supports it" on the Outbound tab of the SMTP connector properties Selected the new self-cert SSL certificate on the SSL tab of the localhost server properties. Given permissions to IME_System on the new certificate However, Gmail is still giving me the following error: Authentication failed. Please check your username/password. [Server response: 454 TLS not available due to temporary reason code(454) ] I'm trying to connect on port 25, (someone told me you can still do this and you dont have to connect on 465). Is this right? Or do I need to tell MailEnable to use port 465? Am I missing something? Thanks, Chris.

    Read the article

  • squid and ftp connections

    - by Kstro21
    i have a squid proxy server for both, http and ftp connections, i'm trying to use filezilla to open a ftp, but it always fail with an error saying: Status: Connection with proxy established, performing handshake... Response: Proxy reply: HTTP/1.0 403 Forbidden Error: Proxy handshake failed: ECONNRESET - Connection reset by peer Error: Connection timed out Error: Failed to retrieve directory listing i sniff the traffic, and, filezilla is trying to connect to a different port and the proxy denied it look, this is a portion of the sniff result CONNECT 201.150.36.227:61179 HTTP/1.1 Host: 201.150.36.227:61179 User-Agent: FileZilla everytime is a different port, so, no way i can allow it in the squid, also, i set the filezilla to use a active connection, same result, passive connection, same result again, so, i'm out of bullets, and i need your help, maybe a setting in the filezilla or in the squid can do the job, so, give a hand here this is the full log of the filezilla Status: Connecting to uhma.mx through proxy Status: Connecting to 172.19.216.13:3128... Status: Connection with proxy established, performing handshake... Response: Proxy reply: HTTP/1.0 200 Connection established Status: Connection established, waiting for welcome message... Response: 220 ProFTPD 1.3.3a Server (a3 FTP CUATRO) [201.150.36.227] Command: USER uhmamx Response: 331 Password required for uhmamx Command: PASS ******* Response: 230 User uhmamx logged in Status: Connected Status: Retrieving directory listing... Command: PWD Response: 257 "/" is the current directory Command: TYPE I Response: 200 Type set to I Command: PASV Response: 227 Entering Passive Mode (201,150,36,227,238,251). Command: MLSD Status: Connecting to 172.19.216.13:3128... Status: Connection with proxy established, performing handshake... Response: Proxy reply: HTTP/1.0 403 Forbidden Error: Proxy handshake failed: ECONNRESET - Connection reset by peer Error: Connection timed out Error: Failed to retrieve directory listing

    Read the article

  • Varnish 3.0.2 and ISPConfig 3.0.4

    - by Warren Bullock III
    I followed the tutorial The Perfect Server - Ubuntu 11.10 [ISPConfig 3] here. I'm running an Ubuntu 11.04 (Natty Narwhal) server with 1024 RAM on Rackspace. I've gone through and updated to ISPConfig 3.0.4. Everything has been working great up to now when I decided to try and install Varnish. Initially I did an install of Varnish by issuing: apt-get update apt-get upgrade apt-get install varnish Apparently the version that was installed was Varnish 2.x so I went back and added the repositories for packages provided by varnish-cache.org curl http://repo.varnish-cache.org/debian/GPG-key.txt | apt-key add - echo "deb http://repo.varnish-cache.org/ubuntu/ lucid varnish-3.0" >> /etc/apt/sources.list apt-get update apt-get install varnish This updated my version of Varnish to 3.0.2 I then proceeded to make the following changes: vim /etc/default/varnish change DAEMON_OPTS to port 80: vim /etc/apache2/ports.conf NameVirtualHost *:8000 Listen 8000 vim /etc/apache2/sites-available/default <VirtualHost *:8000> vim /etc/apache2/sites-available/ispconfig.vhost Listen 8080 NameVirtualHost *:8080 <VirtualHost _default_:8080> I then proceeded to set my other vhosts to use 8000 (the apache2 port) so with all this set I reset both Apache2 and Varnish to test. I used Firebug in Firefox 11.0 The output from what I see doesn't seem to indicate that Varnish is working completely correct: First of all I see: X-Varnish 1644834493 but I've heard that unless you have two timestamps side by side than it's probably not working correctly so for example I was thinking I might see something like: X-Varnish 1644834493 1644837493 Also if I noticed this in the output which seems to be inconstant: X-Drupal-Cache MISS There are times when it will say HIT as well.... So the question here that I have is I think Varnish is partially working, however, why don't I see two timestamps on X-Varnish like I'm thinking I should and does the output of the screenshot I have look correct? If Varnish isn't working can someone tell me what I might being doing wrong? Thanks in advance.

    Read the article

  • Using unixODBC to connect to Oracle server

    - by Paul
    I am trying to configure our web server (RHEL 5.4 x86) to connect to an Oracle database using unixODBC. I have installed unixODBC-2.2.11-7.1.1, which yum tells me is the latest version. I have also installed the Oracle InstantClient 11.2 and the Oracle InstantClient ODBC library. I have symlinked the all the .so files in /usr/lib/oracle/11.2/client/lib to /usr/lib. I have set $LD_LIBRARY_PATH to /usr/lib/, $ORACLE_HOME to /usr/lib/oracle and $TNS_ADMIN to the directory containing my (valid) Tnsnames.ora file. Here are the contents of my /etc/odbcinst.ini file: [Oracle] Description = Oracle ODBC Connection Driver = /usr/lib/libsqora.so.11.1 Setup = FileUsage = and my /etc/odbc.ini file: [Oracle] Application Attributes = T Attributes = W BatchAutocommitMode = IfAllSuccessful CloseCursor = F DisableDPM = F DisableMTS = T Driver = Oracle EXECSchemaOpt = EXECSyntax = T Failover = T FailoverDelay = 10 FailoverRetryCount = 10 FetchBufferSize = 64000 ForceWCHAR = F Lobs = T Longs = T MetadataIdDefault = F QueryTimeout = T ResultSets = T ServerName = //<host>:<port>/<db> SQLGetData extensions = F Translation DLL = Translation Option = 0 UserID = (ServerName has been edited...host, port, and db are actually there, and correct) When I run isql I get $ isql -v Oracle isql: symbol lookup error: /usr/lib/libsqora.so.11.1: undefined symbol: SQLGetPrivateProfileStringW And running dltest gives me $ dltest Oracle SQLConnect [dltest] ERROR dlopen: Oracle: cannot open shared object file: No such file or directory If anyone has any insights I would be grateful, I've been trying to get this to connect for about 5 hours now... I am going home for the night, but will gladly provide more details, if necessary, tomorrow morning, to anyone willing to help...

    Read the article

  • configure a Cisco ASA to use MS-CHAP v2 for RADIUS authentication

    - by DrStalker
    Cisco ASA5505 8.2(2) Windows 2003 AD server We want to configure our ASA (10.1.1.1) to authenticate remote VPN users through RADIUS on the Windows AD controller (10.1.1.200) We have the following entry on the ASA: aaa-server SYSCON-RADIUS protocol radius aaa-server SYSCON-RADIUS (inside) host 10.1.1.200 key ***** radius-common-pw ***** When I test a login using the account COMPANY\username I see the users credentials are correct in the security log, but I get the following in the windows system logs: User COMPANY\myusername was denied access. Fully-Qualified-User-Name = company.com/CorpUsers/AU/My Name NAS-IP-Address = 10.1.1.1 NAS-Identifier = <not present> Called-Station-Identifier = <not present> Calling-Station-Identifier = <not present> Client-Friendly-Name = ASA5510 Client-IP-Address = 10.1.1.1 NAS-Port-Type = Virtual NAS-Port = 7 Proxy-Policy-Name = Use Windows authentication for all users Authentication-Provider = Windows Authentication-Server = <undetermined> Policy-Name = VPN Authentication Authentication-Type = PAP EAP-Type = <undetermined> Reason-Code = 66 Reason = The user attempted to use an authentication method that is not enabled on the matching remote access policy. My assumption is that the ASA is using PAP authentication, instead of MS-CHAP v2; the credentials are confirmed, the proper Remote Access Policy is being used, but this policy is set to only allow MS-CHAP2. What do we need to do on the ASA to make it us MS-CHAP v2? In the ADSM GUI The "Microsoft CHAP v2 compatible" tickbox is enabled, but I don't know what this corresponds to in the config.

    Read the article

  • How do I configure freeSSHd on Windows Server 2008 so I can log in using ssh?

    - by Daryl Spitzer
    I've installed freeSSHd on a Windows Server 2008 box (following the instructions in How to install an SSH Server in Windows Server 2008), including: created a user named "dspitzer" with NTLM authorization opened an exception for port 22 in the Windows Firewall But when I try to connect (from a Mac OS X 10.5.8 command-line), I get permission denied after entering the password: $ ssh 12.34.56.78 [email protected]'s password: Permission denied, please try again. [email protected]'s password: Permission denied, please try again. [email protected]'s password: Received disconnect from 12.34.56.78: 2: Too many attempts. I've also tried: $ ssh [email protected] [email protected]'s password: Permission denied, please try again. [email protected]'s password: Permission denied, please try again. [email protected]'s password: Received disconnect from 12.34.56.78: 2: Too many attempts. I've also tried changing the authorization to "Password stored as SHA1 hash" and entering a simple password, but I get the same problem. And I've tried a different user name ("Administrator") with no luck. I've confirmed that I am connecting to the server I'm configuring—if I stop freeSSHd and try to connect I get: $ ssh 12.34.56.78 ssh: connect to host 12.34.56.78 port 22: Operation timed out I get the exact same results from a Linux command-line. Any advice or troubleshooting tips? Update: I tried disabling the firewall (in response to geeklin's comment) and it made no difference. Update #2: I no longer have this machine (I've changed employers), so I have no way of verifying the answers. I guess all I can do is make this question "community wiki".

    Read the article

  • How do I configure freeSSHd on Windows Server 2008 so I can log in using ssh?

    - by Daryl Spitzer
    I've installed freeSSHd on a Windows Server 2008 box (following the instructions in How to install an SSH Server in Windows Server 2008), including: created a user named "dspitzer" with NTLM authorization opened an exception for port 22 in the Windows Firewall But when I try to connect (from a Mac OS X 10.5.8 command-line), I get permission denied after entering the password: $ ssh 12.34.56.78 [email protected]'s password: Permission denied, please try again. [email protected]'s password: Permission denied, please try again. [email protected]'s password: Received disconnect from 12.34.56.78: 2: Too many attempts. I've also tried: $ ssh [email protected] [email protected]'s password: Permission denied, please try again. [email protected]'s password: Permission denied, please try again. [email protected]'s password: Received disconnect from 12.34.56.78: 2: Too many attempts. I've also tried changing the authorization to "Password stored as SHA1 hash" and entering a simple password, but I get the same problem. And I've tried a different user name ("Administrator") with no luck. I've confirmed that I am connecting to the server I'm configuring—if I stop freeSSHd and try to connect I get: $ ssh 12.34.56.78 ssh: connect to host 12.34.56.78 port 22: Operation timed out I get the exact same results from a Linux command-line. Any advice or troubleshooting tips? Update: I tried disabling the firewall (in response to geeklin's comment) and it made no difference. Update #2: I no longer have this machine (I've changed employers), so I have no way of verifying the answers. I guess all I can do is make this question "community wiki".

    Read the article

  • MultiView 2000 terminal emulator not printing correctly to Generic/Text Printer on Windows 7

    - by FantaFan
    Guys & gals, Hope someone can shed some light on this. I am downloading reports from an AIX-based system by directing them to a TT printer which the terminal emulator (MultiView 2000) intercepts and directs to the default printer on the local system. This local printer is configured as a vanilla Generic/Text printer attached to a FILE port. When I print from AIX, the output is spooled down and the local printer prompts for a file name into which to save the file...but not under Windows 7. This has worked fine for many years, on both Win2K and WinXP. However, on Windows 7 the output gets spooled as a file into spool\PRINTERS (and looks as expected) but the print job then hangs with a status of "Error - Printing" and never prompts for a file name. I have to cancel the job. The Generic/Text printer works as expected with other applications. I have tried setting the printer to print directly rather than spooling but this only serves to hang the terminal session too. I've also tried to run the emulator in Windows 2000 Compatibility Mode and as Administrator in case it was something like that but with no luck. As you might expect, it does work fine in XP Mode (as long as I print to a printer defined therein and not the host's printer) but operationally this isn't going to be an option. Obviously this emulation software is a decade old (at least) and I could just cross/upgrade all the users (at a cost) but, before I do so, has anyone seen this sort of behaviour before and found some sort of fix? Remote OS: AIX 5 Client OS: Windows 7 Pro (32-bit) Printer: Generic/Text on a FILE port TE Software: MultiView 2000 (320-bit) Thanks in advance.

    Read the article

< Previous Page | 248 249 250 251 252 253 254 255 256 257 258 259  | Next Page >