Search Results

Search found 7122 results on 285 pages for 'wait cursor'.

Page 252/285 | < Previous Page | 248 249 250 251 252 253 254 255 256 257 258 259  | Next Page >

  • Replace dual-XP installs with single-XP install and repartition drive?

    - by caeious
    Hello, The Current Situation I have a hard drive that currently is split up like so: Primary Partition C: 9.77 GB NTFS Healthy (System) with XP Pro (in Polish) installed Extended Partition D: 39.82 GB NTFS Healthy (Boot) with XP Pro (in English) installed 6.30 GB Free space When I start my comuter I get a black and white Windows Boot Manager dual boot screen with 2 choices both being Microsoft Windows XP. The first choice is the English version of XP and the second choice is the Polish version of XP. Images of my Computer Management window and Dual Boot screen The Mission What I need to do is get rid of the entire extended partition (D: 39.82 GB & 6.30 free space) and just have the one primary C: drive which I assume will be somewheres around 55 GB big. So in the end I just want XP Pro in English running on my C: drive and no black and white boot screen to show up when starting up my laptop. The Question How do I go about successfully completing The Mission with out making my computer a useless pile of silicon, plastic and metal? UPDATE: So I went ahead and tried to follow Neal's suggestion but hit a wall. I got to a Windows XP Pro install screen that had the 3 following options as well as my drive data: To set up Windows XP on the selected item, press Enter To create a partition in the unpartitioned space, press C To delete the selected partition, press D 57232 MB Disk 0 at Id 0 on bus 0 on atapi [MBR] C: Partition1 [NTFS] 10001 MB ( 4642 MB free ) Unpartitioned space 6448 MB D: Partition2 [NTFS] 40774 MB ( 26225 MB free ) Unpartitioned space 8 MB I figured I would go with the first choice ((To set up Windows XP on the selected item, press Enter)) because I just wanted to set up Windows XP on C: Partition1 (which was preselected) so I pressed Enter which brought me to a screen displaying this message: You chose to install Windows XP on a partition that contains another operating system. Installing Windows XP on this partition might cause the other operating system to function improperly. CAUTION: Installing multiple operating systems on a single partition is not recommended. So this leads me to 2 new questions: How do I get rid of the Windows XP (Polish language) install on C: Partition 1 so that I can cleanly and safely install Windows XP (English language) on it? Neal, is this what you meant by me possibly having to delete the partition that the Windows XP (Polish language) install was located on? Since I have the option to delete partitions with the 3rd choice ((To delete the selected partition, press D)), should I do that on this screen or wait until I have Windows XP (English language) safely installed on C: Partition 1? I have to ask these questions because I have read that it is possibly dangerous to delete hard drive partitions. Just being cautious.

    Read the article

  • Macbook Pro - Randomly sleeps and won't wake up

    - by James
    All, I have a Macbook Pro 13" (mid 2009) that has had a long time issues which seems to be getting worse. Occasionally, I will go to wake the computer with the keyboard and can't wake it. The HDD spins up, the light on the front of the computer stops blinking, but as soon as it seems like the display should light up, the HDD stops and the light begins blinking again. More rarely, the computer will suddenly sleep while I am using it and then enters the same sleep loop. The only way to resume working on the computer is to wait. Doing a hard restart just puts it right back into the 'sleep loop.' Here is an excerpt from kernel.log showing the laptops apparent narcolepsy: Jun 5 22:20:40 james-hales-macbook-pro kernel[0]: Wake reason: OHC1 Jun 5 22:20:40 james-hales-macbook-pro kernel[0]: Previous Sleep Cause: 5 Jun 5 22:20:40 james-hales-macbook-pro kernel[0]: The USB device Apple Internal Keyboard / Trackpad (Port 6 of Hub at 0x4000000) may have caused a wake by issuing a remote wakeup (2) Jun 5 22:20:40 james-hales-macbook-pro kernel[0]: HID tickle 31 ms Jun 5 22:20:41 james-hales-macbook-pro kernel[0]: 00000000 00000020 NVEthernet::setLinkStatus - not Active Jun 5 22:20:45 james-hales-macbook-pro kernel[0]: MacAuthEvent en1 Auth result for: 20:4e:7f:48:c0:ef MAC AUTH succeeded Jun 5 22:20:45 james-hales-macbook-pro kernel[0]: wlEvent: en1 en1 Link UP Jun 5 22:20:45 james-hales-macbook-pro kernel[0]: AirPort: Link Up on en1 Jun 5 22:20:45 james-hales-macbook-pro kernel[0]: en1: BSSID changed to 20:4e:7f:48:c0:ef Jun 5 22:20:46 james-hales-macbook-pro kernel[0]: AirPort: RSN handshake complete on en1 Jun 5 22:20:48 james-hales-macbook-pro kernel[0]: 00000000 00000020 NVEthernet::setLinkStatus - not Active Jun 5 22:20:54 james-hales-macbook-pro kernel[0]: Jun 5 22:20:55 james-hales-macbook-pro kernel[0]: Wake reason: OHC1 Jun 5 22:20:55 james-hales-macbook-pro kernel[0]: Previous Sleep Cause: 5 Jun 5 22:20:55 james-hales-macbook-pro kernel[0]: The USB device Apple Internal Keyboard / Trackpad (Port 6 of Hub at 0x4000000) may have caused a wake by issuing a remote wakeup (2) Jun 5 22:20:55 james-hales-macbook-pro kernel[0]: wlEvent: en1 en1 Link DOWN Jun 5 22:20:55 james-hales-macbook-pro kernel[0]: AirPort: Link Down on en1. Reason 4 (Disassociated due to inactivity). Jun 5 22:20:55 james-hales-macbook-pro kernel[0]: HID tickle 26 ms Jun 5 22:20:55 james-hales-macbook-pro kernel[0]: 00000000 00000020 NVEthernet::setLinkStatus - not Active Jun 5 22:20:58 james-hales-macbook-pro kernel[0]: MacAuthEvent en1 Auth result for: 20:4e:7f:48:c0:ef MAC AUTH succeeded Jun 5 22:20:58 james-hales-macbook-pro kernel[0]: wlEvent: en1 en1 Link UP Jun 5 22:20:58 james-hales-macbook-pro kernel[0]: AirPort: Link Up on en1 Jun 5 22:20:58 james-hales-macbook-pro kernel[0]: en1: BSSID changed to 20:4e:7f:48:c0:ef Jun 5 22:20:58 james-hales-macbook-pro kernel[0]: AirPort: RSN handshake complete on en1 Jun 5 22:21:02 james-hales-macbook-pro kernel[0]: 00000000 00000020 NVEthernet::setLinkStatus - not Active Jun 5 22:21:08 james-hales-macbook-pro kernel[0]: I have tried reseting the SMC and reinstalling Lion (short of erasing and installing) to no avail. The Genius bar has insisted that the problem would be resolved by reinstalling Lion (which they did, but didn't fix anything, still insisting...). Please don't say "logic board." Thoughts?

    Read the article

  • Teamviewer: cannot control monitor 1, but can control monitor 2

    - by DaveT
    I'm using the web client of Teamviewer from my work computer trying to control my home computer. I have 2 monitors on the remote desktop, but for some reason only have control on the second monitor. When I switch to the main monitor (monitor 1), I cannot do anything and cannot even move the cursor. But I have no issues when I switch over to the second monitor (monitor 2). I used to have no issues with either, but in the past couple of months this has been causing me issues. Anyone have a suggestion? Thanks!! Also... Here is the log from the Teamviewer session. Showing me switching back and forth between the monitors. (just in case this will help). I had to remove the links in order to post the log since I don't have enough reputation points, but they were just teamviewer login weblinks. =============================================================================== 21.08 16:00:41,176: Version: 9.0.15099 21.08 16:00:41,177: Sandbox: remote 21.08 16:00:41,177: SysLanguage: en 21.08 16:00:41,177: VarLanguage: en 21.08 16:00:41,177: Flash Player: PlugIn (WIN 14,0,0,179) 21.08 16:00:41,178: UseLanguage: en 21.08 16:00:41,178: UseLanguage: en 21.08 16:00:41,182: TeamViewer hasPassword: true 21.08 16:00:41,418: ExternalConnect id=910035824 21.08 16:00:41,419: CT connect 910035824 masterURL: , sandbox = remote 21.08 16:00:41,425: MC.requestRoute(910035824) 21.08 16:00:41,426: MC.sendMasterCommand text=F=RequestRoute2&ID1=777&Client=TV& ID2=910035824&SA_AccountID=26641022&SA_PasswordMD5HashBase64Encoded=& SA_SessionSecret=f7H6Z7SYfX5ahQ7SJq/r/K20PBYg9fOZhp+DKLhf5ts=&SA_SessionID=1558929948& V=9.0.15099&OS=Flash 21.08 16:00:41,426: MC wait for ping completion 21.08 16:00:42,064: PS.socket event: [Event type="connect" bubbles=false cancelable=false eventPhase=2] 21.08 16:00:42,182: PingThread: TCP-Ping ok 21.08 16:00:42,183: MC.socket mode = TCP, MasterURL: 21.08 16:00:42,183: MC.connect: 21.08 16:00:43,058: PS.socket event: [Event type="connect" bubbles=false cancelable=false eventPhase=2] 21.08 16:00:43,058: MC.connectHandler: [Event type="connect" bubbles=false cancelable=false eventPhase=2] 21.08 16:00:43,236: MC.requestRouteResponse: [email protected]_10800_128000_762319420_910035824_10000__1_0_16778176_128000_16778176: 128000;2147483647:1280000;4:640000_786297_786297 21.08 16:00:43,239: CT init socket: TCP 21.08 16:00:43,513: PS.socket event: [Event type="connect" bubbles=false cancelable=false eventPhase=2] 21.08 16:00:43,514: CT.connectHandler: [Event type="connect" bubbles=false cancelable=false eventPhase=2] 21.08 16:00:43,519: Browser name: Netscape 21.08 16:00:43,936: CMD_IDENTIFY id=910035824 ver=2.41 21.08 16:00:44,666: CMD_CONFIRMENCRYPTION: encryption confirmed 21.08 16:00:44,667: Started resendrequest timer 21.08 16:00:45,063: Remote Version: TV 009.000 21.08 16:00:45,501: start classic authentication 21.08 16:00:45,502: Login::SendRequestToConsole(): url= 21.08 16:00:45,828: start srp authentication 21.08 16:00:46,983: checkFirstPacket ok, m_LastReceivedPacketID =4 21.08 16:00:47,148: Login::SendRequestToConsole(): url= 21.08 16:00:47,478: start srp authentication 21.08 16:00:48,210: Login::SendRequestToConsole(): url= 21.08 16:00:48,485: checkFirstPacket ok, m_LastReceivedPacketID =7 21.08 16:00:48,780: TVCmdAuthenticate_Authenticated: 1 21.08 16:00:49,321: Connected to 910035824, name=NEWMAN, os=14, version=9.0.31064 21.08 16:00:49,329: ConnectionAccessSettings: RemoteControl: AllowedFileTransfer: AllowedControlRemoteTV: AllowedSwitchSides: DeniedAllowDisableRemoteInput: AllowedAllowVPN: AllowedAllowPartnerViewDesktop: Allowed 21.08 16:00:52,195: unexpected TVCommand.CommandType == 56 21.08 16:00:52,231: CW received display params: 1680x1050x8 monitors: 2 (active:0) 21.08 16:00:52,301: Caching active, version=2 21.08 16:03:47,158: CW received display params: 1680x1050x8 monitors: 2 (active:1) 21.08 16:04:24,447: CW received display params: 1680x1050x8 monitors: 2 (active:0) 21.08 16:04:40,609: CW received display params: 3360x1050x8 monitors: 2 (active:-1) 21.08 16:04:59,802: CW received display params: 1680x1050x8 monitors: 2 (active:1) 21.08 16:04:59,933: CW received display params: 1680x1050x8 monitors: 2 (active:1) 21.08 16:05:58,419: CW received display params: 1680x1050x8 monitors: 2 (active:0) 21.08 16:06:36,824: CW received display params: 1680x1050x8 monitors: 2 (active:1) 21.08 16:07:07,232: CW received display params: 1680x1050x8 monitors: 2 (active:0)

    Read the article

  • pxe boot fails with message: no DEFAULT or UI configuration directive found

    - by spockaroo
    I am trying to pxe-boot a machine (client), and in the process I am trying to setup a tftp server that this machine can boot off. On the server, which runs Ubuntu 10.10, I have setup dhcp, dns, nfs, and tftp-hpa servers. All the servers/deamons start fine. I tested the tftp server by using a tftp client and downloading a file that the server directory hosts. My /etc/xinet.d/tftp looks like this service tftp { disable = no socket_type = dgram wait = yes user = nobody server = /usr/sbin/in.tftpd server_args = -v -s /var/lib/tftpboot only_from = 10.1.0.0/24 interface = 10.1.0.1 } My /etc/default/tftpd-hpa looks like this RUN_DAEMON="yes" OPTIONS="-l -s /var/lib/tftpboot" TFTP_USERNAME="tftp" TFTP_DIRECTORY="/var/lib/tftpboot" TFTP_ADDRESS="0.0.0.0:69" TFTP_OPTIONS="--secure" My /var/lib/tftpboot/ directory looks like this initrd.img-2.6.35-25-generic-pae vmlinuz-2.6.35-25-generic-pae pxelinux.0 pxelinux.cfg -- default I did sudo chmod 644 /var/lib/tftpboot/pxelinux.cfg/default chmod 755 /var/lib/tftpboot/initrd.img-2.6.35-25-generic-pae chmod 755 /var/lib/tftpboot/vmlinuz-2.6.35-25-generic-pae /var/lib/tftpboot/pxelinux.cfg has the following contents SERIAL 0 19200 0 LABEL linux KERNEL vmlinuz-2.6.35-25-generic-pae APPEND root=/dev/nfs initrd=initrd.img-2.6.35-25-generic-pae nfsroot=10.1.0.1:/nfsroot ip=dhcp console=ttyS0,19200n8 rw I copied /var/lib/tftpboot/pxelinux.0 from /usr/lib/syslinux/ after installing the package syslinux-common. Also just for completeness, /etc/dhcp3/dhcpd.conf the following lines (relevant to this interface) subnet 10.1.0.0 netmask 255.255.255.0 { range 10.1.0.100 10.1.0.240; option routers 10.1.0.1; option broadcast-address 10.1.0.255; option domain-name-servers 10.1.0.1; filename "pxelinux.0"; } When I boot the client machine, and watch the output over the serial port, I notice that the client requests an ip address from the server and gets it. Then I see TFTP being displayed - indicating that it is trying to connect to the TFTP server. This succeeds, and I see TFTP.|, which return immediately displaying the following message PXELINUX 4.01 debian-20100714 Copyright (C) 1994-2010 H. Peter Anvin et al No DEFAULT or UI configuration directive found! boot: /var/log/syslog shows Feb 20 15:24:05 ch in.tftpd[2821]: tftp: client does not accept options What option is it talking about in the syslog? I assume it is referring to OPTIONS or TFTP_OPTIONS, but what am I doing wrong?

    Read the article

  • JVM process resident set size "equals" max heap size, not current heap size

    - by Volune
    After a few reading about jvm memory (here, here, here, others I forgot...), I am expecting the resident set size of my java process to be roughly equal to the current heap space capacity. That's not what the numbers are saying, it seems to be roughly equal to the max heap space capacity: Resident set size: # echo 0 $(cat /proc/1/smaps | grep Rss | awk '{print $2}' | sed 's#^#+#') | bc 11507912 # ps -C java -O rss | gawk '{ count ++; sum += $2 }; END {count --; print "Number of processes =",count; print "Memory usage per process =",sum/1024/count, "MB"; print "Total memory usage =", sum/1024, "MB" ;};' Number of processes = 1 Memory usage per process = 11237.8 MB Total memory usage = 11237.8 MB Java heap # jmap -heap 1 Attaching to process ID 1, please wait... Debugger attached successfully. Server compiler detected. JVM version is 24.55-b03 using thread-local object allocation. Garbage-First (G1) GC with 18 thread(s) Heap Configuration: MinHeapFreeRatio = 10 MaxHeapFreeRatio = 20 MaxHeapSize = 10737418240 (10240.0MB) NewSize = 1363144 (1.2999954223632812MB) MaxNewSize = 17592186044415 MB OldSize = 5452592 (5.1999969482421875MB) NewRatio = 2 SurvivorRatio = 8 PermSize = 20971520 (20.0MB) MaxPermSize = 85983232 (82.0MB) G1HeapRegionSize = 2097152 (2.0MB) Heap Usage: G1 Heap: regions = 2560 capacity = 5368709120 (5120.0MB) used = 1672045416 (1594.586769104004MB) free = 3696663704 (3525.413230895996MB) 31.144272834062576% used G1 Young Generation: Eden Space: regions = 627 capacity = 3279945728 (3128.0MB) used = 1314914304 (1254.0MB) free = 1965031424 (1874.0MB) 40.089514066496164% used Survivor Space: regions = 49 capacity = 102760448 (98.0MB) used = 102760448 (98.0MB) free = 0 (0.0MB) 100.0% used G1 Old Generation: regions = 147 capacity = 1986002944 (1894.0MB) used = 252273512 (240.5867691040039MB) free = 1733729432 (1653.413230895996MB) 12.702574926293766% used Perm Generation: capacity = 39845888 (38.0MB) used = 38884120 (37.082786560058594MB) free = 961768 (0.9172134399414062MB) 97.58628042120682% used 14654 interned Strings occupying 2188928 bytes. Are my expectations wrong? What should I expect? I need the heap space to be able to grow during spikes (to avoid very slow Full GC), but I would like to have the resident set size as low as possible the rest of the time, to benefit the other processes running on the server. Is there a better way to achieve that? Linux 3.13.0-32-generic x86_64 java version "1.7.0_55" Running in Docker version 1.1.2 Java is running elasticsearch 1.2.0: /usr/bin/java -Xms5g -Xmx10g -XX:MinHeapFreeRatio=10 -XX:MaxHeapFreeRatio=20 -Xss256k -Djava.awt.headless=true -XX:+UseG1GC -XX:MaxGCPauseMillis=350 -XX:InitiatingHeapOccupancyPercent=45 -XX:+AggressiveOpts -XX:+UseCompressedOops -XX:-OmitStackTraceInFastThrow -XX:+PrintGCDetails -XX:+PrintGCTimeStamps -XX:+PrintClassHistogram -XX:+PrintTenuringDistribution -XX:+PrintGCApplicationStoppedTime -XX:+PrintGCApplicationConcurrentTime -Xloggc:/opt/elasticsearch/logs/gc.log -XX:+HeapDumpOnOutOfMemoryError -XX:HeapDumpPath=/opt elasticsearch/logs/heapdump.hprof -XX:ErrorFile=/opt/elasticsearch/logs/hs_err.log -Des.logger.port=99999 -Des.logger.host=999.999.999.999 -Delasticsearch -Des.foreground=yes -Des.path.home=/opt/elasticsearch -cp :/opt/elasticsearch/lib/elasticsearch-1.2.0.jar:/opt/elasticsearch/lib/*:/opt/elasticsearch/lib/sigar/* org.elasticsearch.bootstrap.Elasticsearch There actually are 5 elasticsearch nodes, each in a different docker container. All have about the same memory usage. Some stats about the index: size: 9.71Gi (19.4Gi) docs: 3,925,398 (4,052,694)

    Read the article

  • How can I run supervisord without using root?

    - by Jason Baker
    I seem to be having trouble figuring out why supervisord won't run as a non-root user. If I start it with the user set to jason (pid 1000), I get the following in the log file: 2010-05-24 08:53:32,143 CRIT Set uid to user 1000 2010-05-24 08:53:32,143 WARN Included extra file "/home/jason/src/tsched/celeryd.conf" during parsing 2010-05-24 08:53:32,189 INFO RPC interface 'supervisor' initialized 2010-05-24 08:53:32,189 WARN cElementTree not installed, using slower XML parser for XML-RPC 2010-05-24 08:53:32,189 CRIT Server 'unix_http_server' running without any HTTP authentication checking 2010-05-24 08:53:32,190 INFO daemonizing the supervisord process 2010-05-24 08:53:32,191 INFO supervisord started with pid 3444 ...then the process dies for some unknown reason. If I start it without sudo (under the user jason), I get similar output: 2010-05-24 08:51:32,859 INFO supervisord started with pid 3306 2010-05-24 08:52:15,761 CRIT Can't drop privilege as nonroot user 2010-05-24 08:52:15,761 WARN Included extra file "/home/jason/src/tsched/celeryd.conf" during parsing 2010-05-24 08:52:15,807 INFO RPC interface 'supervisor' initialized 2010-05-24 08:52:15,807 WARN cElementTree not installed, using slower XML parser for XML-RPC 2010-05-24 08:52:15,807 CRIT Server 'unix_http_server' running without any HTTP authentication checking 2010-05-24 08:52:15,808 INFO daemonizing the supervisord process 2010-05-24 08:52:15,809 INFO supervisord started with pid 3397 ...and it still doesn't run. If it's any help, here's the supervisord.conf file I'm using: [unix_http_server] file=/tmp/supervisor.sock ; path to your socket file [supervisord] logfile=./supervisord.log ; supervisord log file logfile_maxbytes=50MB ; maximum size of logfile before rotation logfile_backups=10 ; number of backed up logfiles loglevel=debug ; info, debug, warn, trace pidfile=./supervisord.pid ; pidfile location nodaemon=false ; run supervisord as a daemon minfds=1024 ; number of startup file descriptors minprocs=200 ; number of process descriptors user=jason ; default user childlogdir=./supervisord/ ; where child log files will live [rpcinterface:supervisor] supervisor.rpcinterface_factory = supervisor.rpcinterface:make_main_rpcinterface [supervisorctl] serverurl=unix:///tmp/supervisor.sock ; use unix:// schem for a unix sockets. [include] # Uncomment this line for celeryd for Python files=celeryd.conf # Uncomment this line for celeryd for Django. ;files=django/celeryd.conf ...and here's celeryd.conf: [program:celery] command=bin/celeryd --loglevel=INFO --logfile=./celeryd.log environment=PYTHONPATH='./tsched_worker', JIVA_DB_PLATFORM='oracle', ORACLE_HOME='/usr/lib/oracle/xe/app/oracle/product/10.2.0/server', LD_LIBRARY_PATH='/usr/lib/oracle/xe/app/oracle/product/10.2.0/server/lib', TNS_ADMIN='/home/jason', CELERY_CONFIG_MODULE='tsched_worker.celeryconfig' directory=. user=jason numprocs=1 stdout_logfile=/var/log/celeryd.log stderr_logfile=/var/log/celeryd.log autostart=true autorestart=true startsecs=10 ; Need to wait for currently executing tasks to finish at shutdown. ; Increase this if you have very long running tasks. stopwaitsecs = 600 ; if rabbitmq is supervised, set its priority higher ; so it starts first priority=998 Can anyone help me figure out what's going on?

    Read the article

  • How to calculate CPU % based on raw CPU ticks in SNMP

    - by bjeanes
    According to http://net-snmp.sourceforge.net/docs/mibs/ucdavis.html#scalar_notcurrent ssCpuUser, ssCpuSystem, ssCpuIdle, etc are deprecated in favor of the raw variants (ssCpuRawUser, etc). The former values (which don't cover things like nice, wait, kernel, interrupt, etc) returned a percentage value: The percentage of CPU time spent processing user-level code, calculated over the last minute. This object has been deprecated in favour of 'ssCpuRawUser(50)', which can be used to calculate the same metric, but over any desired time period. The raw values return the "raw" number of ticks the CPU spent: The number of 'ticks' (typically 1/100s) spent processing user-level code. On a multi-processor system, the 'ssCpuRaw*' counters are cumulative over all CPUs, so their sum will typically be N*100 (for N processors). My question is: how do you turn the number of ticks into percentage? That is, how do you know how many ticks per second (it's typically — which implies not always — 1/100s, which either means 1 every 100 seconds or that a tick represents 1/100th of a second). I imagine you also need to know how many CPUs there are or you need to fetch all the CPU values to add them all together. I can't seem to find a MIB that gives you an integer value for # of CPUs which makes the former route awkward. The latter route seems unreliable because some of the numbers overlap (sometimes). For example, ssCpuRawWait has the following warning: This object will not be implemented on hosts where the underlying operating system does not measure this particular CPU metric. This time may also be included within the 'ssCpuRawSystem(52)' counter. Some help would be appreciated. Everywhere seems to just say that % is deprecated because it can be derived, but I haven't found anywhere that shows the official standard way to perform this derivation. The second component is that these "ticks" seem to be cumulative instead of over some time period. How do I sample values over some time period? The ultimate information I want is: % of user, system, idle, nice (and ideally steal, though there doesn't seem to be a standard MIB for this) "currently" (over the last 1-60s would probably be sufficient, with a preference for smaller time spans).

    Read the article

  • Informix "Database locale information mismatch"

    - by lmmortal
    I have informix 11.5 running in my Win-2003 box and few databases running in it. System databases have locale en_us.819 My custom databases have locale en_us.57372 (UTF8). There is also application deployed to JBoss 4.0.2 which has few datasources configured for those custom databases. <local-tx-datasource> <jndi-name>InformixDS</jndi-name> <connection-url>jdbc:informix-sqli://@database.server@:@database.port@/tcs_catalog:[email protected]@</connection-url> <driver-class>com.informix.jdbc.IfxDriver</driver-class> <user-name>@database.username@</user-name> <password>@database.password@</password> <new-connection-sql>set lock mode to wait 5</new-connection-sql> <check-valid-connection-sql>select '1' from dual</check-valid-connection-sql> <metadata> <type-mapping>InformixDB</type-mapping> </metadata> I'm logged in as Administrator and when I start JBoss the following error is shown Caused by: java.sql.SQLException: Database locale information mismatch. at com.informix.util.IfxErrMsg.getSQLException(IfxErrMsg.java:373) at com.informix.jdbc.IfxSqli.a(IfxSqli.java:3208) at com.informix.jdbc.IfxSqli.E(IfxSqli.java:3518) at com.informix.jdbc.IfxSqli.dispatchMsg(IfxSqli.java:2353) at com.informix.jdbc.IfxSqli.receiveMessage(IfxSqli.java:2269) at com.informix.jdbc.IfxSqli.executeOpenDatabase(IfxSqli.java:1786) at com.informix.jdbc.IfxSqliConnect.<init>(IfxSqliConnect.java:1327) at sun.reflect.NativeConstructorAccessorImpl.newInstance0(Native Method) at sun.reflect.NativeConstructorAccessorImpl.newInstance(NativeConstructorAccessorImpl.java:39) at sun.reflect.DelegatingConstructorAccessorImpl.newInstance(DelegatingConstructorAccessorImpl.java:27) at java.lang.reflect.Constructor.newInstance(Constructor.java:501) at com.informix.jdbc.IfxDriver.connect(IfxDriver.java:254) at org.jboss.resource.adapter.jdbc.local.LocalManagedConnectionFactory.createManagedConnection(LocalManagedConnectionFactory.java:151) ... 160 more Caused by: java.sql.SQLException at com.informix.util.IfxErrMsg.getSQLException(IfxErrMsg.java:373) at com.informix.jdbc.IfxSqli.E(IfxSqli.java:3523) ... 170 more DB_LOCALE and CLIENT_LOCALE are set to en_us.utf8 for Administrator. When I set in Server Studio DB_LOCALE and CLIENT_LOCALE to en_us.utf8 I can connect my databases. Where should I set DB_LOCALE and CLIENT_LOCALE to avoid this Database locale information mismatch error? Thanks.

    Read the article

  • No network upsets gnome

    - by Darren Cook
    An issue that has been bothering me for over a year now. My notebook, running ubuntu 10.04, is almost all the time using a wired connection, with static IP address. And a remote DNS server. Network is configured with entries in /etc/network/interfaces and /etc/resolv.conf, rather than whatever the gnome UI tool was (*) But if I'm out, or simply unplug the network cable, a few things get weird. Specifically the gnome-panel stops working - it is still there, but isn't updating. And opening a nautilus window (e.g. to look at files on the local disk) has huge time-outs. By that I mean it will not open the window for something like 30 or 60 seconds; but when it does finally open it I can see the files and it is perfectly usable. Everything else works fine, alt-tab between windows, etc. I use the commandline to find the pid of gnome-panel, kill it, wait a couple of seconds, and it opens up a fresh panel which is normally usable. (Something like 10 minutes later it will have locked/crashed again; the same for the nautilus windows.) I'm guessing this is a DNS issue? Would setting up a local DNS server help? Guess number 2 was related to having a file server mount (samba, though running on another linux box), and symbolic links to files and directories on that file server on my desktop. My question is a bit vague... Does anyone recognize these symptoms, and have a suggestion? Or do you have some troubleshooting suggestions for narrowing down the problem? My /etc/hosts: 127.0.0.1 localhost 127.0.1.1 myhost # The following lines are desirable for IPv6 capable hosts ::1 localhost ip6-localhost ip6-loopback fe00::0 ip6-localnet ff00::0 ip6-mcastprefix ff02::1 ip6-allnodes ff02::2 ip6-allrouters ff02::3 ip6-allhosts 127.0.0.1 testsite.local #Other test website URLs here UPDATE: Some timings to open some desktop folder icons. This is after pulling out the network cable. A sub-directory of the desktop took 23 secs to open up. Content appears immediately (just 8 files, it has no further subdirectories). The home directory icon took 12 seconds to open up, but then took about 30 seconds for the files to appear. I closed it and tried again. This time it took 18 seconds to open up, but then 70 seconds before anything appeared. *: I couldn't work out how to use the gnome network tool for my needs, which include 3-4 static IPs for testing virtual hosts locally.

    Read the article

  • csync2 ERROR: Connection to remote host failed

    - by Emil Salama
    I was unable to find any articles to answer this question, so my best bet was to post this here: Scenario We have 2x application servers in production hosting a PHP website and I would like some folders to be syncronized between the 2, the same was setup for the development environment with no issues, I've followed all instructions from the URL "http://www.cloudedify.com/synchronising-files-in-cloud-with-csync2/", I still seem to have the same result, firewall has been disabled on both boxes for troubeshooting purposes: Config Files: cysnc2.cfg nossl * *; group production { host server1; host server2; key /etc/csync-production-group.key; include /etc/httpd/sites-available; include /xxxxxx/public_html/files include /xxxxxxx/magento/media/catalog/product include /xxxxxxx/magento/media/brands exclude *.log; exclude /xxxx/public_html/file/cache; exclude /xxxxx/public_html/magento/var/cache; exclude /xxxx/public_html/logs; exclude /xxxxx/public_html/magento/var/log; backup-directory /data/sync-conflicts/; backup-generations 2; auto younger; } /etc/xinetd.d/csync2 csync2.cfg service csync2 { disable = no flags = REUSE socket_type = stream wait = no user = root group = root server = /usr/sbin/csync2 server_args = -i -D /data/sync-db/ port = 30865 type = UNLISTED log_type = FILE /data/logs/csync2/csync2-xinetd.log log_on_failure += USERID } I've made sure that the daemon is listening on both server on port 30865 and the keys matched on both servers I've run a tcpdump on each server, output as follows: 12:20:31.366771 IP server1.49919 server2.csync2: Flags [S], seq 445156159, win 14600, options [mss 1460,sackOK,TS val 794864936 ecr 0,nop,wscale 7], length 0 12:20:31.366810 IP server2.csync2 server1.49919: Flags [S.], seq 450593575, ack 445156160, win 14480, options [mss 1460,sackOK,TS val 794798911 ecr 794864936,nop,wscale 7], length 0 12:20:31.367101 IP server1.49919 server2.csync2: Flags [.], ack 1, win 115, options [nop,nop,TS val 794864937 ecr 794798911], length 0 12:20:31.367138 IP server1.49919 server2.csync2: Flags [P.], seq 1:9, ack 1, win 115, options [nop,nop,TS val 794864937 ecr 794798911], length 8 12:20:31.367147 IP server2.csync2 server1.49919: Flags [.], ack 9, win 114, options [nop,nop,TS val 794798912 ecr 794864937], length 0 12:20:31.368625 IP server2.csync2 server1.49919: Flags [R.], seq 1, ack 9, win 114, options [nop,nop,TS val 794798913 ecr 794864937], length 0 Is there anything else i'm missing or should be doing?

    Read the article

  • Accidentally Removed Permissions for the XP SP3 Registry key HKEY_CLASSES_ROOT! Workaround Please!

    - by Praveen Kumar
    This is Praveen and I am using Microsoft Windows XP SP3 Build 2600. I had problems with using Microsoft Office 2010. It was keeping on saying, "Please wait while windows configures Microsoft Office Professional Plus 2010". After seeing this link: http://social.answers.microsoft.com/Forums/en-US/outlookcontact/thread/6e9c3f2e-010a-4b74-b433-0c41548ee468?prof=required I thought of giving the Registry Key: HKEY_CLASSES_ROOT, full access permissions for Everyone. I went to the registry, right-clicked on HKEY_CLASSES_ROOT and clicked on Permissions. I added Everyone and gave Full Control to the ACL and clicked on Apply. Also I checked "Replace permission entries on all child objects with entries shown here that apply to child objects." After a long time, it said with an error, cannot replace for few entries. Now, the key, HKEY_CLASSES_ROOT has no access to any user. My system is not starting up. Some of my friends asked me to try the Last Known Good Configuration. Even that did not work out. When I tried to open in the Safe Mode, I got only one driver to load and even that didn't load well. Another friend suggested me to put the Setup disk and reinstall the OS. I tried that and after completing the "Installing Device Drivers" part, when it started "Installing Network", the system is getting restarted. Now, the setup is also half way through and even if I open in Safe Mode to try System Restore, it popped up a message saying, "Setup cannot run under Safe Mode. Setup will restart now." and the system is restarting. All my official files and my software, which I developed for Registry Security, resides in my system now. I am unable to access the system and I want it to be working to submit the project, as the deadline is this week. I had no better solutions from elsewhere. Can anyone please help me out with this issue. If it is possible to open the registry editor's stored file from another system and restore the access permissions, I hope it would solve the problem. Please do help me. Thanking You, Praveen.

    Read the article

  • How to transition to Comcast with static IP address

    - by steveha
    I have my own email server in my house, on a static IP address. I have had business DSL for over a decade, but I also now have Comcast business Internet. I want to transition from the DSL to the Comcast, and I have some questions. I have a domain name, my own mail server, and a firewall (a PC with two network interfaces, running Devil-Linux). I need to make sure I understand how to set up the Comcast cable box, and how to set up my firewall. First, do I need to change any settings in the cable box? Currently I have only used the cable box by plugging in a laptop, with the laptop doing DHCP. I think I can leave the box alone but I would like to make sure. Second, I'm not sure I understand the instructions Comcast gave me for setting up the firewall. My DSL provider gave me the following information: static IP address, net mask, gateway, and two DNS servers. Comcast gave me: static IP address, routable static IP address, net mask, and two DNS servers, and told me to put the "static IP address" as the "gateway" on the firewall. Is this just Comcast-speak here? Does "routable static IP address" mean the same thing as "static IP address" in my DSL setup, the end-point address that I should publish in the DNS MX records for my email server? Or should I publish the "static IP address", and Comcast will then route all its traffic over the cable box? My plan is: first, I'm going to configure another firewall, so I have one firewall for the DSL and one for the Comcast (rather than madly editing settings to switch back and forth). Then I will publish the new Comcast static IP address as a backup email server address in the DNS MX records, wait a while to let it propagate, and then switch my home over from the DSL to the Comcast. Then I'll change DNS to make that the primary mail address and the DSL the secondary, let that go a while and make sure it seems reliable. Then I'll remove the DSL from the DNS MX records completely, and finally shut down the DSL service. (I thought about keeping the DSL as a backup, but the reason I'm leaving DSL is that it has become unreliable; and I have heard that Comcast business Internet is reliable.) Final question, any advice for me? Anything you think might be useful, helpful, or educational. Thanks.

    Read the article

  • iptables (NAT/PAT) setup for SSH & Samba

    - by IanVaughan
    I need to access a Linux box via SSH & Samba that is hidden/connected behind another one. Setup :- A switch B C |----| |---| |----| |----| |eth0|----| |----|eth0| | | |----| |---| |eth1|----|eth1| |----| |----| Eg, SSH/Samba from A to C How does one go about this? I was thinking that it cannot be done via IP alone? Or can it? Could B say "hi on eth0, if your looking for 192.168.0.2, its here on eth1"? Is this NAT? This is a large private network, so what about if another PC has that IP?! More likely it would be PAT? A would say "hi 192.168.109.15:1234" B would say "hi on eth0, traffic for port 1234 goes on here eth1" How could that be done? And would the SSH/Samba demons see the correct packet header info and work?? IP info :- A - eth0 - 192.168.109.2 B - eth0 - B1 = 192.168.109.15 B2 = 172.24.40.130 - eth1 - 192.168.0.1 C - eth1 - 192.168.0.2 A, B & C are RHEL (RedHat) But Windows computers can be connected to the switch. I configured the 192.168.0.* IPs, they are changeable. Update after response from Eddie Few problems (and Machines' B IP is different!) From A :- ssh 172.24.40.130 works ok, (can get to B2) but ssh 172.24.40.130 -p 2022 -vv times out with :- OpenSSH_4.3p2, OpenSSL 0.9.8e-fips-rhel5 01 Jul 2008 debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for * debug2: ssh_connect: needpriv 0 debug1: Connecting to 172.24.40.130 [172.24.40.130] port 2022. ...wait ages... debug1: connect to address 172.24.40.130 port 2022: Connection timed out ssh: connect to host 172.24.40.130 port 2022: Connection timed out From B2 :- $ service iptables status Table: filter Chain INPUT (policy ACCEPT) num target prot opt source destination Chain FORWARD (policy ACCEPT) num target prot opt source destination 1 ACCEPT tcp -- 0.0.0.0/0 192.168.0.2 tcp dpt:22 Chain OUTPUT (policy ACCEPT) num target prot opt source destination Table: nat Chain PREROUTING (policy ACCEPT) num target prot opt source destination 1 DNAT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:2022 to:192.168.0.2:22 Chain POSTROUTING (policy ACCEPT) num target prot opt source destination Chain OUTPUT (policy ACCEPT) num target prot opt source destination And ssh from B2 to C works fine :- $ ssh 192.168.0.2 Route info :- $ route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.0.0 * 255.255.255.0 U 0 0 0 eth1 172.24.40.0 * 255.255.255.0 U 0 0 0 eth0 169.254.0.0 * 255.255.0.0 U 0 0 0 eth1 default 172.24.40.1 0.0.0.0 UG 0 0 0 eth0 $ ip route 192.168.0.0/24 dev eth1 proto kernel scope link src 192.168.0.1 172.24.40.0/24 dev eth0 proto kernel scope link src 172.24.40.130 169.254.0.0/16 dev eth1 scope link default via 172.24.40.1 dev eth0 So I just dont know why the port forward doesnt work from A to B2?

    Read the article

  • ActiveMQ Pure Master / Slave - Out of sync

    - by pico
    What i have : 1 master broker and 1 slave broker both in ActiveMQ 5.4.0 What i use : waitForSlave on master side and failover uri on slave side (in the master connector URI) What i want to do : I want to wait some delay (like 5 seconds) in case of a tiny network failures between master and slave before starting slave transpôrt connectors So i put this in slave config : <broker xmlns="http://activemq.apache.org/schema/core" brokerName="slave" dataDirectory="${activemq.base}/data" useJmx="true" persistent="true" populateJMSXUserID="true" masterConnectorURI="failover://(tcp://master:61616)?initialReconnectDelay=1000&amp;maxReconnectDelay=30000" shutdownOnMasterFailure="false" advisorySupport="false"> It seems to work but after a network hang between master and slave, the slave reconnect successfully and then the master logs a lot of : 2010-10-18 17:08:44,421 | ERROR | Slave Failed | org.apache.activemq.broker.ft.MasterBroker | ActiveMQ Task java.lang.IllegalStateException: Cannot lookup a connection that had not been registered: ID:master-1040-634226732611718750-0:0 at org.apache.activemq.broker.MapTransportConnectionStateRegister.lookupConnectionState(MapTransportConnectionStateRegister.java:93) at org.apache.activemq.broker.TransportConnection.lookupConnectionState(TransportConnection.java:1412) at org.apache.activemq.broker.TransportConnection.processRemoveConsumer(TransportConnection.java:561) at org.apache.activemq.command.RemoveInfo.visit(RemoveInfo.java:76) at org.apache.activemq.broker.TransportConnection.service(TransportConnection.java:309) at org.apache.activemq.broker.TransportConnection$1.onCommand(TransportConnection.java:185) at org.apache.activemq.transport.ResponseCorrelator.onCommand(ResponseCorrelator.java:116) at org.apache.activemq.transport.TransportFilter.onCommand(TransportFilter.java:69) at org.apache.activemq.transport.vm.VMTransport.iterate(VMTransport.java:218) at org.apache.activemq.thread.DedicatedTaskRunner.runTask(DedicatedTaskRunner.java:98) at org.apache.activemq.thread.DedicatedTaskRunner$1.run(DedicatedTaskRunner.java:36) On the slave side everything is fine. So after that, i've tried to stop the master to see if the slave is capable of turning master after these "network hangs". The master took long time to shutdown (10 seconds) and then some error message appears in slave logs : 2010-10-18 17:09:32,915 | WARN | Async error occurred: java.lang.IllegalStateException: Cannot lookup a connection that had not been registered: ID:master-1049-634226732657812500-0:3 | org.apache.activemq.broker.TransportConnection.Service | VMTransport: vm://slave#5 java.lang.IllegalStateException: Cannot lookup a connection that had not been registered: ID:master-1049-634226732657812500-0:3 at org.apache.activemq.broker.MapTransportConnectionStateRegister.lookupConnectionState(MapTransportConnectionStateRegister.java:93) at org.apache.activemq.broker.TransportConnection.lookupConnectionState(TransportConnection.java:1412) at org.apache.activemq.broker.TransportConnection.processRemoveSession(TransportConnection.java:600) at org.apache.activemq.command.RemoveInfo.visit(RemoveInfo.java:74) at org.apache.activemq.broker.TransportConnection.service(TransportConnection.java:309) at org.apache.activemq.broker.TransportConnection$1.onCommand(TransportConnection.java:185) at org.apache.activemq.transport.ResponseCorrelator.onCommand(ResponseCorrelator.java:116) at org.apache.activemq.transport.TransportFilter.onCommand(TransportFilter.java:69) at org.apache.activemq.transport.vm.VMTransport.iterate(VMTransport.java:218) at org.apache.activemq.thread.DedicatedTaskRunner.runTask(DedicatedTaskRunner.java:98) at org.apache.activemq.thread.DedicatedTaskRunner$1.run(DedicatedTaskRunner.java:36) Are they any ways to keep my kaha stores (they are individual stores) synchronised? The main problem is that the slave never turn master after a master failure, it stay block on this message : 2010-10-18 17:09:33,681 | WARN | Transport (master/172.21.60.61:61616) failed to tcp://master:61616 , attempting to automatically reconnect due to: java.net.SocketException: Software caused connection abort: socket write error | org.apache.activemq.transport.failover.FailoverTransport | ActiveMQ Transport: tcp://master/172.21.60.61:61616 I'm totally stuck with these syncs problems, any help welcome! Regards

    Read the article

  • How to shutdown VMware Fusion virtual machine on host shutdown

    - by Nikksno
    I have a Mac mini running Mavericks server. I installed the Atmail server + webmail vm [a linux centos distribution] in VMware Fusion Professional 6 with the VMware Tools addon. It works flawlessly. I've set it to start on boot and that works very reliably. However I've been looking for a way to also safely and gracefully shut it down whenever OS X shuts down for whatever reason. The Mac is connected to a UPS and configured to perform an automatic shutdown in case the battery starts running low so that's no additional problem. Now the first thing I did was to go into Fusion's prefs and select "Power off the vm" when closing it. However I noticed that for some arcane reason closing the vm window would actually forcibly power off the vm: so then I found this post that showed me how to change the default power options and I managed to have the vm cleanly shutdown when closing its window or quitting Fusion altogether. At this point I was hoping to have solved the problem but as it turns out upon invoking system shutdown OS X doesn't wait for the vm to shutdown and terminates Fusion before it has a chance to do so. At this point I started looking for a way to automate the process of shutting down the guest os via some advanced setting but had no luck in doing so. That's when I found a command to shut the vm down: vmrun and it worked. The only thing left was to find out a way to execute this script on os x shutdown and giving it a little time to power off completely. However this turned out to be a nightmare: I spent hours looking through several ways to do this with Startup Items, rc.shutdown, cron, launchd, etc... but none of them worked the way I had configured them. I have to say that I found very limited information on using launchd for a shutdown script execution and I know it's the latest thing in the OS X world so I'm hoping someone out there among you will be able to help me out with this. I still think this is an extremely basic feature to ask for and I was really surprised to find this little documentation on so many different aspects of this problem. Is Fusion too basic of an application for this? I really hope someone can help. Thank you very much in advance.

    Read the article

  • How to transition to Comcast with static IP address [migrated]

    - by steveha
    I have my own email server in my house, on a static IP address. I have had business DSL for over a decade, but I also now have Comcast business Internet. I want to transition from the DSL to the Comcast, and I have some questions. I have a domain name, my own mail server, and a firewall (a PC with two network interfaces, running Devil-Linux). I need to make sure I understand how to set up the Comcast cable box, and how to set up my firewall. First, do I need to change any settings in the cable box? Currently I have only used the cable box by plugging in a laptop, with the laptop doing DHCP. I think I can leave the box alone but I would like to make sure. Second, I'm not sure I understand the instructions Comcast gave me for setting up the firewall. My DSL provider gave me the following information: static IP address, net mask, gateway, and two DNS servers. Comcast gave me: static IP address, routable static IP address, net mask, and two DNS servers, and told me to put the "static IP address" as the "gateway" on the firewall. Is this just Comcast-speak here? Does "routable static IP address" mean the same thing as "static IP address" in my DSL setup, the end-point address that I should publish in the DNS MX records for my email server? Or should I publish the "static IP address", and Comcast will then route all its traffic over the cable box? My plan is: first, I'm going to configure another firewall, so I have one firewall for the DSL and one for the Comcast (rather than madly editing settings to switch back and forth). Then I will publish the new Comcast static IP address as a backup email server address in the DNS MX records, wait a while to let it propagate, and then switch my home over from the DSL to the Comcast. Then I'll change DNS to make that the primary mail address and the DSL the secondary, let that go a while and make sure it seems reliable. Then I'll remove the DSL from the DNS MX records completely, and finally shut down the DSL service. (I thought about keeping the DSL as a backup, but the reason I'm leaving DSL is that it has become unreliable; and I have heard that Comcast business Internet is reliable.) Final question, any advice for me? Anything you think might be useful, helpful, or educational. Thanks.

    Read the article

  • sftp and public keys

    - by Lizard
    I am trying to sftp into an a server hosted by someone else. To make sure this worked I did the standard sftp [email protected] i was promted with the password and that worked fine. I am setting up a cron script to send a file once a week so have given them our public key which they claim to have added to their authorized_keys file. I now try sftp [email protected] again and I am still prompted for a password, but now the password doesn't work... Connecting to [email protected]... [email protected]'s password: Permission denied, please try again. [email protected]'s password: Permission denied, please try again. [email protected]'s password: Permission denied (publickey,password). Couldn't read packet: Connection reset by peer I did notice however that if I simply pressed enter (no password) it logged me in fine... So here are my questions: Is there a way to check what privatekey/pulbickey pair my sftp connection is using? Is it possible to specify what key pair to use? If all is setup correctly (using correct key pair and added to authorized files) why am I being asked to enter a blank password? Thanks for your help in advance! UPDATE I have just run sftp -vvv [email protected] .... debug1: Authentications that can continue: publickey,password debug3: start over, passed a different list publickey,password debug3: preferred gssapi-with-mic,publickey,keyboard-interactive,password debug3: authmethod_lookup publickey debug3: remaining preferred: keyboard-interactive,password debug3: authmethod_is_enabled publickey debug1: Next authentication method: publickey debug1: Offering public key: /root/.ssh/id_rsa debug3: send_pubkey_test debug2: we sent a publickey packet, wait for reply debug1: Server accepts key: pkalg ssh-rsa blen 277 debug2: input_userauth_pk_ok: SHA1 fp 45:1b:e7:b6:33:41:1c:bb:0f:e3:c1:0f:1b:b0:d5:e4:28:a3:3f:0e debug3: sign_and_send_pubkey debug1: read PEM private key done: type RSA debug1: Authentications that can continue: publickey,password debug1: Trying private key: /root/.ssh/id_dsa debug3: no such identity: /root/.ssh/id_dsa debug2: we did not send a packet, disable method debug3: authmethod_lookup password debug3: remaining preferred: ,password debug3: authmethod_is_enabled password debug1: Next authentication method: password It seems to suggest that it tries to use the public key... What am I missing?

    Read the article

  • Windows 7 boot problem (with colorful blinking smilies)

    - by Ishmael Smyrnow
    I put my computer (Windows 7) to sleep, and a couple hours later, tried to wake it back up, but the monitor wouldn't come back on. I did a hard reset (held power button), but I still couldn't get the monitor to show anything. I plugged it into my laptop, and the monitor works fine. I then swapped out the video card with an older one I have. The monitor came on and started showing the boot process. However, shortly after the Windows 7 animated logo came up, the screen went blank, it made this weird beeping noise, and I seen the strangest thing ever. Small, colorful blocks started to fill my screen, and flash, as if something was loading. Inside of those blocks, were smilies (like the ASCII character kind). This continued for about a minute, then the computer rebooted. It scared the sh!t out of me. I've never had a virus before, and I'm savvy enough to keep myself from one, but I'm wondering if that's what it was. I've been using computers for ages, and never seen anything quite like this. Has anyone ever seen something like this? I'm doing hardware diagnostics before trying to boot into Windows again. Hopefully I can figure this out, but I thought I would consult the SU community while I wait on these results. -- UPDATE -- I did a Memory Diagnostic, which turned up nothing. I also booted into Safe Mode no problem, and scheduled a disk check on both of my drives (I dual boot XP & 7). I was feeling good, and tried putting my regular video card back in, and the monitor won't display anything with it. Also, even though the monitor displays nothing, the system sounds like it's booting up. However, I hear a clicking in one of my hard drives that isn't there with the older video card. Could this be a problem with my hard drive, video card, or PSU? PSU makes sense, except for the fact I've been using the same setup for over a year, and the video card doesn't require it's own power plug thing.

    Read the article

  • apache mod_cache in v2.2 - enable cache based on url

    - by Janning
    We are using apache2.2 as a front-end server with application servers as reverse proxies behind apache. We are using mod_cache for some images and enabled it like this: <IfModule mod_disk_cache.c> CacheEnable disk / CacheRoot /var/cache/apache2/mod_disk_cache CacheIgnoreCacheControl On CacheMaxFileSize 2500000 CacheIgnoreURLSessionIdentifiers jsessionid CacheIgnoreHeaders Set-Cookie </IfModule> The image urls vary completely and have no common start pattern, but they all end in ".png". Thats why we used the root in CacheEnable / If not served from the cache, the request is forwarded to an application server via reverse proxy. So far so good, cache is working fine. But I really only need to cache all image request ending in ".png". My above configuration still works as my application server send an appropriate Cache-Control: no-cache header on the way back to apache. So most pages send a no-cache header back and they get not cached at all. My ".png" responses doesn't send a Cache-Control header so apache is only going to cache all urls with ".png". Fine. But when a new request enters apache, apache does not know that only .png requests should be considered, so every request is checking a file on disk (recorded with strace -e trace=file -p pid): [pid 19063] open("/var/cache/apache2/mod_disk_cache/zK/q8/Kd/g6OIv@woJRC_ba_A.header", O_RDONLY|O_CLOEXEC) = -1 ENOENT (No such file or directory) I don't want to have apache going to disk every request, as the majority of requests are not cached at all. And we have up to 10.000 request/s at peak time. Sometimes our read IO wait spikes. It is not getting really slow, but we try to tweak it for better performance. In apache 2.4 you can say: <LocationMatch .png$> CacheEnable disk </LocationMatch> This is not possible in 2.2 and as I see no backports for debian I am not going to upgrade. So I tried to tweak apache2.2 to follow my rules: <IfModule mod_disk_cache.c> SetEnvIf Request_URI "\.png$" image RequestHeader unset Cache-Control RequestHeader append Cache-Control no-cache env=!image CacheEnable disk / CacheRoot /var/cache/apache2/mod_disk_cache #CacheIgnoreCacheControl on CacheMaxFileSize 2500000 CacheIgnoreURLSessionIdentifiers jsessionid CacheIgnoreHeaders Set-Cookie </IfModule> The idea is to let apache decide to serve request from cache based on Cache-control header (CacheIgnoreCacheControl default to off). And before simply set a RequestHeader based on the request. If it is not an image request, set a Cache-control header, so it should bypass the cache at all. This does not work, I guess because of late processing of RequestHeader directive, see https://httpd.apache.org/docs/2.2/mod/mod_headers.html#early I can't add early processing as "early" keyword can't be used together with a conditional "env=!image" I can't change the url requesting the images and I know there are of course other solutions. But I am only interested in configuring apache2.2 to reach my goal. Does anybody has an idea how to achieve my goal?

    Read the article

  • Python error after installing libboost-all-dev on debian [migrated]

    - by Cameron Metzke
    A friend of mine wanted the liboost libraries installed on our shared computer so after installing libboost-all-dev 1.49.0.1 ( A debian wheezy machine ), I get this error when using the "pydoc modules" command on the commandline. It spits out the following error -- root@debian:/usr/include/c++/4.7# pydoc modules Please wait a moment while I gather a list of all available modules... **[debian:49065] [[INVALID],INVALID] ORTE_ERROR_LOG: A system-required executable either could not be found or was not executable by this user in file ../../../../../../orte/mca/ess/singleton/ess_singleton_module.c at line 357 [debian:49065] [[INVALID],INVALID] ORTE_ERROR_LOG: A system-required executable either could not be found or was not executable by this user in file ../../../../../../orte/mca/ess/singleton/ess_singleton_module.c at line 230 [debian:49065] [[INVALID],INVALID] ORTE_ERROR_LOG: A system-required executable either could not be found or was not executable by this user in file ../../../orte/runtime/orte_init.c at line 132 -------------------------------------------------------------------------- It looks like orte_init failed for some reason; your parallel process is likely to abort. There are many reasons that a parallel process can fail during orte_init; some of which are due to configuration or environment problems. This failure appears to be an internal failure; here's some additional information (which may only be relevant to an Open MPI developer): orte_ess_set_name failed --> Returned value A system-required executable either could not be found or was not executable by this user (-127) instead of ORTE_SUCCESS -------------------------------------------------------------------------- -------------------------------------------------------------------------- It looks like MPI_INIT failed for some reason; your parallel process is likely to abort. There are many reasons that a parallel process can fail during MPI_INIT; some of which are due to configuration or environment problems. This failure appears to be an internal failure; here's some additional information (which may only be relevant to an Open MPI developer): ompi_mpi_init: orte_init failed --> Returned "A system-required executable either could not be found or was not executable by this user" (-127) instead of "Success" (0) -------------------------------------------------------------------------- *** The MPI_Init() function was called before MPI_INIT was invoked. *** This is disallowed by the MPI standard. *** Your MPI job will now abort. [debian:49065] Abort before MPI_INIT completed successfully; not able to guarantee that all other processes were killed!** root@debian:/usr/include/c++/4.7# I tried looking into the problem and ended up uninstalling the following to get it to work again. openmpi common all 1.4.5-1 libibverbs-dev amd64 1.1.6-1 libopenmpi-dev amd64 1.4.5-1 mpi-default-dev amd64 1.0.1 libboost-mpi-python1.49.0 although pydoc works again, I'm assuming the packages I removed are gunna hurt somethiong else down the track ? As you guessed im not a c/c++ programmer. So I guess my question is, will this hurt something later ? is their a way to install those packages without hurting python ?

    Read the article

  • Nameserver not resolving or domain not pingable [closed]

    - by Ricky
    Sorry, if anyone can think of a better title please change it! I want to host my own websites from home. For testing purposes, I have a virtual machine running a trial version of Windows Server 2008 Enterprise. Note I currently run a VPS and host my own websites but due to a nice speed upgrade on our line I now want to host from home. I have several domains but I wanted to test with one, that is rickyoleary.com. Our ISP does not provide static IP addresses unless we have a business account so I've been looking at no-ip.com. I admit my networking isn't the best, hence this question but I've been bashing my head all day on this one. I created a host name, muffinbubble.no-ip.org which runs on IP: 86.148.124.15. I've setup IIS on the server with a simple test page. I've then forwarded port 80 traffic from the router and from what I can see, it's working. If I access my website (I was unable to link to this for some reason so please copy and paste this) - http://86.148.124.15/ - I see my test page. So the next step was to create my nameservers. This domain is with namecheap.com so I created my nameservers, ns1.rickyoleary.com and ns2.rickyoleary.com. Both these point to the same IP (and yes, that will be changed after testing), the same IP as above: 86.148.124.15. On the server itself I have set up DNS entries as below which I believe to be correct and added rickyoleary.com and www.rickyoleary.com in the host headers (or bindings) in IIS 7.0. If I try and look up my domain, rickyoleary.com it shows ns1.rickyoleary.com and ns2.rickyoleary.com as the nameservers. I then tried to use just-ping.com on my nameserver ns1.rickyoleary.com. I get 100% packets lost, but the correct IP address is returned (I'm guessing the router does not allow pings, but is still accessible...). I get no response when pinging rickyoleary.com. Here's the problems: I cannot ping ns1.rickyoleary.com or ns2.rickyoleary.com from a command prompt. I'm not sure if this is an issue. When I added the nameservers in Windows Server 2008 and clicked 'resolve' a message box displays stating "No such host is known". I cannot ping rickyoleary.com. rickyoleary.com is not showing my test page on my server. Now - please note, I've waited around 6 hours for propagation. From my experience, although you're told to wait 24 - 48 hours, the changes are normally pretty quick so perhaps I'm being impatient or naive to think it should all be working fine until then. I would really appreciate some help here. Thanks.

    Read the article

  • Adaptec 5805 after reboot don't starting

    - by Rakedko ShotGuns
    After rebooting the system, the controller is not included. It only works if the computer is shut down and turn off. Late i update firmware "Adaptec RAID 5805 Firmware Build 18948" How to fix the problem? add Log Configuration summary Server name.....................raid_test Adaptec Storage Manager agent...7.31.00 (18856) Adaptec Storage Manager console.7.31.00 (18856) Number of controllers...........1 Operating system................Windows Configuration information for controller 1 ------------------------------------------------------- Type............................Controller Model...........................Adaptec 5805 Controller number...............1 Physical slot...................2 Installed memory size...........512 MB Serial number...................8C4510C6C9E Boot ROM........................5.2-0 (18948) Firmware........................5.2-0 (18948) Device driver...................5.2-0 (16119) Controller status...............Optimal Battery status..................Charging Battery temperature.............Normal Battery charge amount (%).......37 Estimated charge remaining......0 days, 16 hours, 12 minutes Background consistency check....Disabled Copy back.......................Disabled Controller temperature..........Normal (40C / 104F) Default logical drive task priorityHigh Performance mode................Dynamic Number of logical devices.......1 Number of hot-spare drives......0 Number of ready drives..........0 Number of drive(s) assigned to MaxCache cache0 Maximum drives allowed for MaxCache cache8 MaxCache Read Cache Pool Size...0 GB NCQ status......................Enabled Stay awake status...............Disabled Internal drive spinup limit.....0 External drive spinup limit.....0 Phy 0...........................No device attached Phy 1...........................No device attached Phy 2...........................No device attached Phy 3...........................1.50 Gb/s Phy 4...........................No device attached Phy 5...........................No device attached Phy 6...........................No device attached Phy 7...........................No device attached Statistics version..............2.0 SSD Cache size..................0 Pages on fetch list.............0 Fetch list candidates...........0 Candidate replacements..........0 69319...........................31293 Logical device..................0 Logical device name............. RAID level......................Simple volume Data space......................148,916 GB Date created....................09/19/2012 Interface type..................Serial ATA State...........................Optimal Read-cache mode.................Enabled Preferred MaxCache read cache settingEnabled Actual MaxCache read cache setting Disabled Write-cache mode................Enabled (write-back) Write-cache setting.............Enabled (write-back) Partitioned.....................Yes Protected by hot spare..........No Bootable........................Yes Bad stripes.....................No Power Status....................Disabled Power State.....................Active Reduce RPM timer................Never Power off timer.................Never Verify timer....................Never Segment 0.......................Present: controller 1, connector 0, device 0, S/N 9RX3KZMT Overall host IOs................99075 Overall MB......................4411203 DRAM cache hits.................71929 SSD cache hits..................0 Uncached IOs....................29239 Overall disk failures...........0 DRAM cache full hits............71929 DRAM cache fetch / flush wait...0 DRAM cache hybrid reads.........3476 DRAM cache flushes..............-- Read hits.......................0 Write hits......................0 Valid Pages.....................0 Updates on writes...............0 Invalidations by large writes...0 Invalidations by R/W balance....0 Invalidations by replacement....0 Invalidations by other..........0 Page Fetches....................0 0...............................0 73..............................10822 8...............................3 46138...........................4916 27184...........................15226 20875...........................323 16982...........................1771 1563............................5317 1948............................2969 Serial attached SCSI ----------------------- Type............................Disk drive Vendor..........................Unknown Model...........................ST3160815AS Serial Number...................9RX3KZMT Firmware level..................3.AAD Reported channel................0 Reported SCSI device ID.........0 Interface type..................Serial ATA Size............................149,05 GB Negotiated transfer speed.......1.50 Gb/s State...........................Optimal S.M.A.R.T. error................No Write-cache mode................Write back Hardware errors.................0 Medium errors...................0 Parity errors...................0 Link failures...................0 Aborted commands................0 S.M.A.R.T. warnings.............0 Solid-state disk (non-spinning).false MaxCache cache capable..........false MaxCache cache assigned.........false NCQ status......................Enabled Phy 0...........................1.50 Gb/s Power State.....................Full rpm Supported power states..........Full rpm, Powered off 0x01............................113 0x03............................98 0x04............................99 0x05............................100 0x07............................83 0x09............................75 0x0A............................100 0x0C............................99 0xBB............................100 0xBD............................100 0xBE............................61 0xC2............................39 0xC3............................69 0xC5............................100 0xC6............................100 0xC7............................200 0xC8............................100 0xCA............................100 Aborted commands................0 Link failures...................0 Medium errors...................0 Parity errors...................0 Hardware errors.................0 SMART errors....................0 End of the configuration information for controller 1 List item

    Read the article

  • Windows 7 x64 "upgrade" repair fails

    - by Polynomial
    I've been running into issues with Windows Update, which I can't seem to fix. The hotfixes don't work, nor does the Windows update readyness tool, or the manual SP1 upgrade. I get various esoteric errors which nobody seems to have a fix for. Looks like some of the update cache is corrupt and digital signatures seem to be broken on some packages / Windows Update components. Long story short, I have discovered the only option is to do a repair operation on the OS, to repair everything. It's so corrupt that only a complete replacement will fix it. According to various sources (including MSKB) one can perform a repair by running an in-place upgrade. I've got the Windows 7 Ultimate retail disc, which I've inserted into my machine. I ran setup.exe and went through in the following order: Install now Go online to get latest updates (I've also tried not getting updates) Wait for updates to be downloaded Select Windows 7 Ultimate (x64 architecture) and click next Accept the T&Cs, click next Click Upgrade At this point it spends a minute on the "checking compatibility" screen, after which I get the following error: The following issues are preventing Windows from upgrading. Cancel the upgrade, complete each task, and then restart the upgrade to continue. You can’t upgrade 64-bit Windows to a 32-bit version of Windows. To upgrade, obtain a 64-bit version of the installation disc, or go online to see how to install Windows 7 and keep your files and settings. 32-bit Windows cannot be upgraded to a 64-bit version of Windows. To upgrade, obtain a 32-bit version of the Windows installation disc. It also mentions a warning about potential conflicts with a storage driver and VS2010, but that doesn't seem to be the blocking issue. My currently installed version of Windows is Ultimate 64-bit (absolutely sure of this) and the disc is definitely a x86 / x64 combined Ultimate retail disc. There seem to be a few people who have run into this (e.g. this question), but I've not seen any answers. I've checked the event viewer, but can't spot anything in there that's related. Any idea how I can get this working? P.S: Just to pre-empt the inevitable "are you suuuuuuuuuuuuure it's x64 Ultimate?" questions:

    Read the article

  • Disable .htaccess from apache allowoverride none, still reads .htaccess files

    - by John Magnolia
    I have moved all of our .htaccess config into <Directory> blocks and set AllowOverride None in the default and default-ssl. Although after restarting apache it is still reading the .htaccess files. How can I completely turn off reading these files? Update of all files with "AllowOverride" /etc/apache2/mods-available/userdir.conf <IfModule mod_userdir.c> UserDir public_html UserDir disabled root <Directory /home/*/public_html> AllowOverride FileInfo AuthConfig Limit Indexes Options MultiViews Indexes SymLinksIfOwnerMatch IncludesNoExec <Limit GET POST OPTIONS> Order allow,deny Allow from all </Limit> <LimitExcept GET POST OPTIONS> Order deny,allow Deny from all </LimitExcept> </Directory> </IfModule> /etc/apache2/mods-available/alias.conf <IfModule alias_module> # # Aliases: Add here as many aliases as you need (with no limit). The format is # Alias fakename realname # # Note that if you include a trailing / on fakename then the server will # require it to be present in the URL. So "/icons" isn't aliased in this # example, only "/icons/". If the fakename is slash-terminated, then the # realname must also be slash terminated, and if the fakename omits the # trailing slash, the realname must also omit it. # # We include the /icons/ alias for FancyIndexed directory listings. If # you do not use FancyIndexing, you may comment this out. # Alias /icons/ "/usr/share/apache2/icons/" <Directory "/usr/share/apache2/icons"> Options Indexes MultiViews AllowOverride None Order allow,deny Allow from all </Directory> </IfModule> /etc/apache2/httpd.conf # # Directives to allow use of AWStats as a CGI # Alias /awstatsclasses "/usr/share/doc/awstats/examples/wwwroot/classes/" Alias /awstatscss "/usr/share/doc/awstats/examples/wwwroot/css/" Alias /awstatsicons "/usr/share/doc/awstats/examples/wwwroot/icon/" ScriptAlias /awstats/ "/usr/share/doc/awstats/examples/wwwroot/cgi-bin/" # # This is to permit URL access to scripts/files in AWStats directory. # <Directory "/usr/share/doc/awstats/examples/wwwroot"> Options None AllowOverride None Order allow,deny Allow from all </Directory> Alias /awstats-icon/ /usr/share/awstats/icon/ <Directory /usr/share/awstats/icon> Options None AllowOverride None Order allow,deny Allow from all </Directory> /etc/apache2/sites-available/default-ssl <IfModule mod_ssl.c> <VirtualHost _default_:443> ServerAdmin webmaster@localhost DocumentRoot /var/www <Directory /> Options FollowSymLinks AllowOverride None </Directory> <Directory /var/www/> Options Indexes FollowSymLinks MultiViews AllowOverride None </Directory> ScriptAlias /cgi-bin/ /usr/lib/cgi-bin/ <Directory "/usr/lib/cgi-bin"> AllowOverride None Options +ExecCGI -MultiViews +SymLinksIfOwnerMatch Order allow,deny Allow from all </Directory> ErrorLog ${APACHE_LOG_DIR}/error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn CustomLog ${APACHE_LOG_DIR}/ssl_access.log combined # SSL Engine Switch: # Enable/Disable SSL for this virtual host. SSLEngine on # A self-signed (snakeoil) certificate can be created by installing # the ssl-cert package. See # /usr/share/doc/apache2.2-common/README.Debian.gz for more info. # If both key and certificate are stored in the same file, only the # SSLCertificateFile directive is needed. SSLCertificateFile /etc/ssl/certs/ssl-cert-snakeoil.pem SSLCertificateKeyFile /etc/ssl/private/ssl-cert-snakeoil.key # Server Certificate Chain: # Point SSLCertificateChainFile at a file containing the # concatenation of PEM encoded CA certificates which form the # certificate chain for the server certificate. Alternatively # the referenced file can be the same as SSLCertificateFile # when the CA certificates are directly appended to the server # certificate for convinience. #SSLCertificateChainFile /etc/apache2/ssl.crt/server-ca.crt # Certificate Authority (CA): # Set the CA certificate verification path where to find CA # certificates for client authentication or alternatively one # huge file containing all of them (file must be PEM encoded) # Note: Inside SSLCACertificatePath you need hash symlinks # to point to the certificate files. Use the provided # Makefile to update the hash symlinks after changes. #SSLCACertificatePath /etc/ssl/certs/ #SSLCACertificateFile /etc/apache2/ssl.crt/ca-bundle.crt # Certificate Revocation Lists (CRL): # Set the CA revocation path where to find CA CRLs for client # authentication or alternatively one huge file containing all # of them (file must be PEM encoded) # Note: Inside SSLCARevocationPath you need hash symlinks # to point to the certificate files. Use the provided # Makefile to update the hash symlinks after changes. #SSLCARevocationPath /etc/apache2/ssl.crl/ #SSLCARevocationFile /etc/apache2/ssl.crl/ca-bundle.crl # Client Authentication (Type): # Client certificate verification type and depth. Types are # none, optional, require and optional_no_ca. Depth is a # number which specifies how deeply to verify the certificate # issuer chain before deciding the certificate is not valid. #SSLVerifyClient require #SSLVerifyDepth 10 # Access Control: # With SSLRequire you can do per-directory access control based # on arbitrary complex boolean expressions containing server # variable checks and other lookup directives. The syntax is a # mixture between C and Perl. See the mod_ssl documentation # for more details. #<Location /> #SSLRequire ( %{SSL_CIPHER} !~ m/^(EXP|NULL)/ \ # and %{SSL_CLIENT_S_DN_O} eq "Snake Oil, Ltd." \ # and %{SSL_CLIENT_S_DN_OU} in {"Staff", "CA", "Dev"} \ # and %{TIME_WDAY} >= 1 and %{TIME_WDAY} <= 5 \ # and %{TIME_HOUR} >= 8 and %{TIME_HOUR} <= 20 ) \ # or %{REMOTE_ADDR} =~ m/^192\.76\.162\.[0-9]+$/ #</Location> # SSL Engine Options: # Set various options for the SSL engine. # o FakeBasicAuth: # Translate the client X.509 into a Basic Authorisation. This means that # the standard Auth/DBMAuth methods can be used for access control. The # user name is the `one line' version of the client's X.509 certificate. # Note that no password is obtained from the user. Every entry in the user # file needs this password: `xxj31ZMTZzkVA'. # o ExportCertData: # This exports two additional environment variables: SSL_CLIENT_CERT and # SSL_SERVER_CERT. These contain the PEM-encoded certificates of the # server (always existing) and the client (only existing when client # authentication is used). This can be used to import the certificates # into CGI scripts. # o StdEnvVars: # This exports the standard SSL/TLS related `SSL_*' environment variables. # Per default this exportation is switched off for performance reasons, # because the extraction step is an expensive operation and is usually # useless for serving static content. So one usually enables the # exportation for CGI and SSI requests only. # o StrictRequire: # This denies access when "SSLRequireSSL" or "SSLRequire" applied even # under a "Satisfy any" situation, i.e. when it applies access is denied # and no other module can change it. # o OptRenegotiate: # This enables optimized SSL connection renegotiation handling when SSL # directives are used in per-directory context. #SSLOptions +FakeBasicAuth +ExportCertData +StrictRequire <FilesMatch "\.(cgi|shtml|phtml|php)$"> SSLOptions +StdEnvVars </FilesMatch> <Directory /usr/lib/cgi-bin> SSLOptions +StdEnvVars </Directory> # SSL Protocol Adjustments: # The safe and default but still SSL/TLS standard compliant shutdown # approach is that mod_ssl sends the close notify alert but doesn't wait for # the close notify alert from client. When you need a different shutdown # approach you can use one of the following variables: # o ssl-unclean-shutdown: # This forces an unclean shutdown when the connection is closed, i.e. no # SSL close notify alert is send or allowed to received. This violates # the SSL/TLS standard but is needed for some brain-dead browsers. Use # this when you receive I/O errors because of the standard approach where # mod_ssl sends the close notify alert. # o ssl-accurate-shutdown: # This forces an accurate shutdown when the connection is closed, i.e. a # SSL close notify alert is send and mod_ssl waits for the close notify # alert of the client. This is 100% SSL/TLS standard compliant, but in # practice often causes hanging connections with brain-dead browsers. Use # this only for browsers where you know that their SSL implementation # works correctly. # Notice: Most problems of broken clients are also related to the HTTP # keep-alive facility, so you usually additionally want to disable # keep-alive for those clients, too. Use variable "nokeepalive" for this. # Similarly, one has to force some clients to use HTTP/1.0 to workaround # their broken HTTP/1.1 implementation. Use variables "downgrade-1.0" and # "force-response-1.0" for this. BrowserMatch "MSIE [2-6]" \ nokeepalive ssl-unclean-shutdown \ downgrade-1.0 force-response-1.0 # MSIE 7 and newer should be able to use keepalive BrowserMatch "MSIE [17-9]" ssl-unclean-shutdown </VirtualHost> </IfModule> /etc/apache2/sites-available/default <VirtualHost *:80> ServerAdmin webmaster@localhost DocumentRoot /var/www <Directory /> Options FollowSymLinks AllowOverride None </Directory> <Directory /var/www/> Options -Indexes FollowSymLinks MultiViews AllowOverride None Order allow,deny allow from all </Directory> ScriptAlias /cgi-bin/ /usr/lib/cgi-bin/ <Directory "/usr/lib/cgi-bin"> AllowOverride None Options +ExecCGI -MultiViews +SymLinksIfOwnerMatch Order allow,deny Allow from all </Directory> Alias /delboy /usr/share/phpmyadmin <Directory /usr/share/phpmyadmin> # Restrict phpmyadmin access Order Deny,Allow Allow from all </Directory> ErrorLog ${APACHE_LOG_DIR}/error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn CustomLog ${APACHE_LOG_DIR}/access.log combined Alias /doc/ "/usr/share/doc/" <Directory "/usr/share/doc/"> Options Indexes MultiViews FollowSymLinks AllowOverride None Order deny,allow Deny from all Allow from 127.0.0.0/255.0.0.0 ::1/128 </Directory> </VirtualHost> /etc/apache2/conf.d/security # # Disable access to the entire file system except for the directories that # are explicitly allowed later. # # This currently breaks the configurations that come with some web application # Debian packages. # #<Directory /> # AllowOverride None # Order Deny,Allow # Deny from all #</Directory> # Changing the following options will not really affect the security of the # server, but might make attacks slightly more difficult in some cases. # # ServerTokens # This directive configures what you return as the Server HTTP response # Header. The default is 'Full' which sends information about the OS-Type # and compiled in modules. # Set to one of: Full | OS | Minimal | Minor | Major | Prod # where Full conveys the most information, and Prod the least. # #ServerTokens Minimal ServerTokens OS #ServerTokens Full # # Optionally add a line containing the server version and virtual host # name to server-generated pages (internal error documents, FTP directory # listings, mod_status and mod_info output etc., but not CGI generated # documents or custom error documents). # Set to "EMail" to also include a mailto: link to the ServerAdmin. # Set to one of: On | Off | EMail # #ServerSignature Off ServerSignature On # # Allow TRACE method # # Set to "extended" to also reflect the request body (only for testing and # diagnostic purposes). # # Set to one of: On | Off | extended # TraceEnable Off #TraceEnable On /etc/apache2/apache2.conf # # Based upon the NCSA server configuration files originally by Rob McCool. # # This is the main Apache server configuration file. It contains the # configuration directives that give the server its instructions. # See http://httpd.apache.org/docs/2.2/ for detailed information about # the directives. # # Do NOT simply read the instructions in here without understanding # what they do. They're here only as hints or reminders. If you are unsure # consult the online docs. You have been warned. # # The configuration directives are grouped into three basic sections: # 1. Directives that control the operation of the Apache server process as a # whole (the 'global environment'). # 2. Directives that define the parameters of the 'main' or 'default' server, # which responds to requests that aren't handled by a virtual host. # These directives also provide default values for the settings # of all virtual hosts. # 3. Settings for virtual hosts, which allow Web requests to be sent to # different IP addresses or hostnames and have them handled by the # same Apache server process. # # Configuration and logfile names: If the filenames you specify for many # of the server's control files begin with "/" (or "drive:/" for Win32), the # server will use that explicit path. If the filenames do *not* begin # with "/", the value of ServerRoot is prepended -- so "foo.log" # with ServerRoot set to "/etc/apache2" will be interpreted by the # server as "/etc/apache2/foo.log". # ### Section 1: Global Environment # # The directives in this section affect the overall operation of Apache, # such as the number of concurrent requests it can handle or where it # can find its configuration files. # # # ServerRoot: The top of the directory tree under which the server's # configuration, error, and log files are kept. # # NOTE! If you intend to place this on an NFS (or otherwise network) # mounted filesystem then please read the LockFile documentation (available # at <URL:http://httpd.apache.org/docs/2.2/mod/mpm_common.html#lockfile>); # you will save yourself a lot of trouble. # # Do NOT add a slash at the end of the directory path. # #ServerRoot "/etc/apache2" # # The accept serialization lock file MUST BE STORED ON A LOCAL DISK. # LockFile ${APACHE_LOCK_DIR}/accept.lock # # PidFile: The file in which the server should record its process # identification number when it starts. # This needs to be set in /etc/apache2/envvars # PidFile ${APACHE_PID_FILE} # # Timeout: The number of seconds before receives and sends time out. # Timeout 300 # # KeepAlive: Whether or not to allow persistent connections (more than # one request per connection). Set to "Off" to deactivate. # KeepAlive On # # MaxKeepAliveRequests: The maximum number of requests to allow # during a persistent connection. Set to 0 to allow an unlimited amount. # We recommend you leave this number high, for maximum performance. # MaxKeepAliveRequests 100 # # KeepAliveTimeout: Number of seconds to wait for the next request from the # same client on the same connection. # KeepAliveTimeout 4 ## ## Server-Pool Size Regulation (MPM specific) ## # prefork MPM # StartServers: number of server processes to start # MinSpareServers: minimum number of server processes which are kept spare # MaxSpareServers: maximum number of server processes which are kept spare # MaxClients: maximum number of server processes allowed to start # MaxRequestsPerChild: maximum number of requests a server process serves <IfModule mpm_prefork_module> StartServers 5 MinSpareServers 5 MaxSpareServers 10 MaxClients 150 MaxRequestsPerChild 500 </IfModule> # worker MPM # StartServers: initial number of server processes to start # MaxClients: maximum number of simultaneous client connections # MinSpareThreads: minimum number of worker threads which are kept spare # MaxSpareThreads: maximum number of worker threads which are kept spare # ThreadLimit: ThreadsPerChild can be changed to this maximum value during a # graceful restart. ThreadLimit can only be changed by stopping # and starting Apache. # ThreadsPerChild: constant number of worker threads in each server process # MaxRequestsPerChild: maximum number of requests a server process serves <IfModule mpm_worker_module> StartServers 2 MinSpareThreads 25 MaxSpareThreads 75 ThreadLimit 64 ThreadsPerChild 25 MaxClients 150 MaxRequestsPerChild 0 </IfModule> # event MPM # StartServers: initial number of server processes to start # MaxClients: maximum number of simultaneous client connections # MinSpareThreads: minimum number of worker threads which are kept spare # MaxSpareThreads: maximum number of worker threads which are kept spare # ThreadsPerChild: constant number of worker threads in each server process # MaxRequestsPerChild: maximum number of requests a server process serves <IfModule mpm_event_module> StartServers 2 MaxClients 150 MinSpareThreads 25 MaxSpareThreads 75 ThreadLimit 64 ThreadsPerChild 25 MaxRequestsPerChild 0 </IfModule> # These need to be set in /etc/apache2/envvars User ${APACHE_RUN_USER} Group ${APACHE_RUN_GROUP} # # AccessFileName: The name of the file to look for in each directory # for additional configuration directives. See also the AllowOverride # directive. # AccessFileName .htaccess # # The following lines prevent .htaccess and .htpasswd files from being # viewed by Web clients. # <Files ~ "^\.ht"> Order allow,deny Deny from all Satisfy all </Files> # # DefaultType is the default MIME type the server will use for a document # if it cannot otherwise determine one, such as from filename extensions. # If your server contains mostly text or HTML documents, "text/plain" is # a good value. If most of your content is binary, such as applications # or images, you may want to use "application/octet-stream" instead to # keep browsers from trying to display binary files as though they are # text. # DefaultType text/plain # # HostnameLookups: Log the names of clients or just their IP addresses # e.g., www.apache.org (on) or 204.62.129.132 (off). # The default is off because it'd be overall better for the net if people # had to knowingly turn this feature on, since enabling it means that # each client request will result in AT LEAST one lookup request to the # nameserver. # HostnameLookups Off # ErrorLog: The location of the error log file. # If you do not specify an ErrorLog directive within a <VirtualHost> # container, error messages relating to that virtual host will be # logged here. If you *do* define an error logfile for a <VirtualHost> # container, that host's errors will be logged there and not here. # ErrorLog ${APACHE_LOG_DIR}/error.log # # LogLevel: Control the number of messages logged to the error_log. # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. # LogLevel warn # Include module configuration: Include mods-enabled/*.load Include mods-enabled/*.conf # Include all the user configurations: Include httpd.conf # Include ports listing Include ports.conf # # The following directives define some format nicknames for use with # a CustomLog directive (see below). # If you are behind a reverse proxy, you might want to change %h into %{X-Forwarded-For}i # LogFormat "%v:%p %h %l %u %t \"%r\" %>s %O \"%{Referer}i\" \"%{User-Agent}i\"" vhost_combined LogFormat "%h %l %u %t \"%r\" %>s %O \"%{Referer}i\" \"%{User-Agent}i\"" combined LogFormat "%h %l %u %t \"%r\" %>s %O" common LogFormat "%{Referer}i -> %U" referer LogFormat "%{User-agent}i" agent # Include of directories ignores editors' and dpkg's backup files, # see README.Debian for details. # Include generic snippets of statements Include conf.d/ # Include the virtual host configurations: Include sites-enabled/

    Read the article

  • Profiles and using the local profile for a domain user

    - by Harry
    I’m having some trouble with profiles and would like to reach out for some help. I’ve tried to do some research to help myself along, but I’m not making much progress on my own. I’ve pretty much taken over the sys admin duties for my small lab, I don’t have much experience to justify it besides I’m the only with the time and dedication to go at it (The environment was in a state of disrepair). My network and domain I look over are extremely small by most standards, about 10 users at a time. They are pretty intensive activity on the network, and we do work with fairly large files. None of the network is online, which is nice at the moment because it allows me not to have another headache. On to my profile problem, I have set up roaming profiles for the users in the network. Now after a little research, I think I will be switching this to a hybrid of folder redirection and roaming profiles as this seems to best practice. I also don’t want the users having to wait for a long time if they have a bloated profile. Now I’ve finally got a build working using MDT. We have Mac Pros, and it wasn’t fun getting everything to play nice. The way I did this was by setting up a reference computer and installing all the software and tools that each user would need and editing the settings preferences to how we would need them. I think used MDT to do a sys prep and capture to create the image of my reference computer. Using the reference image I can push out my images to the rest of the desktops in my environment. The issue I’m having is when we join the computer to domain. The user can login and operate fine on the computer, but I’d like a more. When the user is logged on with their domain user name they lose a lot of the icons I had on my reference image, as well as the desktop background and some other miscellaneous settings. I would love to have the user log on using their domain user name and see the icons and desktop environment as I had it setup on the reference computer. I’m not sure if it is possible, or something simple that I’m missing, but any help would be greatly appreciated!

    Read the article

< Previous Page | 248 249 250 251 252 253 254 255 256 257 258 259  | Next Page >