Search Results

Search found 16472 results on 659 pages for 'computer scientist'.

Page 253/659 | < Previous Page | 249 250 251 252 253 254 255 256 257 258 259 260  | Next Page >

• When modern computers boot, what initial setup of RAM do they execute, and how does it exactly work?

  - by user272840

  I know the title reeks of confusion, and some of you might assume I am just wondering about how the computer boots in general, but I'm not. But I'll sort this out for you people now: 1.Onboard firmware is how mostly all modern computer devices work, whether or not with EFI/UEFI(even without "onboard firmware", older computers still employed bank switching, or similar methods with snap-in firmware, cartridges, etc.) 2.On startup there is no "programs" running in the traditional sense yet, i.e. no kernel, OS, user-applications; all of the instructions, especially the very first instruction, is specified by the Instruction Pointer, I am guessing. How is the IP/PC/etc. set to first point to an address for a BIOS/firmware/etc. instruction, and how do the BIOS instructions map themself out in memory prior to startup? 3.Aside from MMIO, BIOS uses certain RAM addresses to have instructions. The big ? comes in when I ask this ... how does BIOS do this? Conclusion: I am assuming that with the very first instruction there is an initial hardware setup for BIOS prior to complete OS bootup. What I want to know is if it's hardware engineered to always work this way, if there's another step in this bootup method I am missing, a gap of information I am unaware of, or how this all works from the very first instruction, and the RAM data itself.

  Read the article

• Can I boot up a virtual machine natively?

  - by Anshul

  My question is: Is is possible to run a virtual machine natively on your hardware if you have installed the proper drivers etc? In other words, can I use a VHD as a regular hard drive to boot from? The reason I want to do this is that I do both graphics-intensive and audio-intensive work, but my computer is not powerful enough to handle both at the same time and many times I install a bunch of audio programs that I don't want affecting the stability of my graphics programs. Basically I wanted to have sandboxing between the two sets of applications. So I tried running the graphics-intensive programs in a VirtualBox VM and the audio-intensive work natively (simply because it's a pain to route ASIO audio devices in/out of VirtualBox). This kind-of works - the graphics-intensive stuff is tolerable, but still relatively slow, because it's running inside a VM. So my next idea was to just dual-boot and install the graphics and audio programs in separate partitions but I frequently use them in tandem, so it wouldn't be practical to reboot my machine every time I need to use the other set of programs. But I could live with this scenario: If I need to do more audio-intensive stuff, I'll just boot up to the audio partition and run the graphics programs in a VM, and then when I'm working heavily on the graphics part, I'll just boot the graphics partition as a regular OS directly on the hardware. Is this possible? For example by booting up a VHD as a regular hard drive? Or by setting up dual-boot, and every time the audio partition is shut down, synchronize the graphics VM VHD with the native graphics partition? Is it practical, given the above scenario? And if it's not possible, barring buying another computer, can anyone suggest a best-of-all-worlds setup (the two worlds being performance, sandboxing, and running in parallel) for the above scenario? Thanks in advance.

  Read the article

• Unusable network, packet losses between router and NIC

  - by KáGé

  I have this setup: Gigabyte P35-DS3P motherboard Asus NX1101 PCI network card (the one on the motherboard got fried a few years ago by a power surge) Asus RT-N16 router Windows 7 x64 I think the other specs are irrelevant here, but I'll post them if you say so. Until a week ago everything was fine, but then my network became unusable: websites start loading but timeout before anything would come through (true for the web interface of the router as well), I can't reach the computer from my notebook and Windows' ping utility measures a ~50% packet loss between the computer and the router. Pinging localhost is good. The router works completely fine when wired to my notebook. I also tested different ports on the router, different cables, different router and connecting directly to the modem, but it's still the same. Sometimes it works for a few minutes right after turning on the machine, but then it becomes crap again, but mostly it's useless from the start. I've tried updating the firmware on the router, updating the driver for the network card (after which I started getting BSoDs in every 15 minutes), reinstalling Windows, swapping to Fedora 15 but none of them changed anything. Does this mean that the network card is dying, or could it be something else? If it's the card, what model do you recommend as a replacement? (Could be PCI or PCI-Ex x1) Thanks for your help.

  Read the article

• iTunes copy just metadata (song and album ratings, playlists) from iPod

  - by Jared Updike

  I have an iPod touch that I synched with my Windows computer (iTunes 9.0 I think) until my harddrive failed and I lost my entire library. I rebuilt the library (songs) from a year old backup (and various other source for songs) but my playlists and ratings are of course a year old. My iPod itself has most of the playlists and ratings I care most about (favorite songs and albums, rated 4 and 5, for example). I have a catch 22 situation where I feel nervous that I haven't backed up my iPod in around 4 months (when my drive failed) so I'd like to back it up as soon as possible... but if I back it up I have to clear all the songs and playlists and copy them back, which I can't really do since I need to rebuild my playlists on my computer first (using the data only available on my iPod!) The question: is there a better way to READ the information off my iPod than doing it manually, song by song and album by album and playlist by playlist (XML, text dump, database, spreadsheet, anything). In other words, mostly I want the information (metadata like ratings and playlists, not songs) copied off the iPod so I can more quickly get my iTunes library ratings and playlists re-built (manually) so I can finally wipe the music and back up my apps, etc. Then I'd like to copy the music back immediately. The part I'd like to avoid is manually navigating everything on my iPod to read through all the playlists and ratings (50 GB, 6,000+ songs) as I re-enter all of that data by hand. I've done a few dozen albums and it's pretty time consuming having to tap around on the iPod. Reading from a spreadsheet (for example, or XML which I could write a script to get into spreadsheet form) would probably help tremendously, plus then I'd have a backup of that information somewhere besides just my iPod.

  Read the article

• No boot device found. Press any key to continue

  - by Andrew Banks

  I took out the hard drive from my Dell Latitude E5420 notebook, put in an ADATA S599 solid state drive, and installed Ubuntu 11.10. When I boot, the Dell BIOS splash screen appears with a progress bar, which quickly fills up, and the screen goes black. All of this is like it was before. At this point, the OS splash screen should fade in. Instead, I was dismayed to see simply the following, in white text on a black screen: No boot device found. Press any key to continue After looking around for the Any key (just kidding) I press a key, and the Dell BIOS splash screen appears again with a progress bar, which quickly fills up, and the screen goes black. This time, however, the Ubuntu splash screen shows up, Ubuntu opens up, and all is normal. Every time I shut down, however, this happens again. It's like a game the computer and I play together. The computer has never started up without first saying: No boot device found. Press any key to continue and it has always started up after I press any key to continue. It also starts up fine if I click Restart instead of Shut Down. Thoughts?

  Read the article

• Using Active Directory through a Firewall

  - by Adam Brand

  I had kind of a weird setup today where I wanted to enable Windows Firewall on a Windows 2003 R2 SP2 computer that would act as an Active Directory Domain Controller. I didn't see one resource on the Internet that listed what would be required to do this, so I thought I'd list them here and see if anyone has anything to add/sees something that isn't necessary. Ports to Open with "subnet" scope: 42 | TCP | WINS (if you use it) 53 | TCP | DNS 53 | UDP | DNS 88 | TCP | Kerberos 88 | UDP | Kerberos 123 | UDP | NTP 135 | TCP | RPC 135 | UDP | RPC 137 | UDP | NetBIOS 138 | UDP | NetBIOS 139 | TCP | NetBIOS 389 | TCP | LDAP 389 | UDP | LDAP 445 | TCP | SMB 445 | UDP | SMB 636 | TCP | LDAPS 3268 | TCP | GC LDAP 3269 | TCP | GC LDAP Ports to Open with "Any" Scope (for DHCP) 67 | UDP | DHCP 2535 | UDP | DHCP ALSO You need to restrict RPC to use fixed ports instead of everything 1024. For that, you need to add two registry keys: HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\NTDS\Parameters Registry value: TCP/IP Port Value type: REG_DWORD Value data: <-- pick a port like 1600 and put it here HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\Netlogon\Parameters Registry value: DCTcpipPort Value type: REG_DWORD Value data: <-- pick another port like 1650 and put it here ...don't forget to add entries in the firewall to allow those in (TCP, Subnet scope). After doing all that, I was able to add a client computer to the AD domain (behind Windows Firewall) and log in successfully.

  Read the article

• My bios datetime is resetting to 2002, what should I do?

  - by Thierry Lam

  I bought my PC brand new in mid-2006. I'm currently dual booting Win XP 32 bits and Ubuntu Karmic Desktop. Over the last few days, when I boot up my computer, it tells me that my bios time is not set. I now have 2 choices for booting in: Windows first: I can safely get into Windows but the date now shows 2002/01/01 at 00:00. From there, Windows will not sync its time to its servers, I have to manually advance the date myself. I can also advance the date from the bios at startup. Ubuntu first: Since the time date is still set at 2002, the boot system cannot find my linux partition. I can fix that issue by booting to Windows, set the date properly and the linux issue will be fixed automatically. The above two issues can also be fixed if I manually set the bios date/time manually when I turn on my computer. It's annoying to do that every single day since I shut down my PC daily. Am I having an OS issue or a hardware issue? How can I resolve this problem?

  Read the article

• All FireFTP passwords gone after auto-update

  - by GitaarLAB

  For the last six months (since the Firefox madness started and they keep on taking control of my PC) I'm terrified to touch Firefox. Problem is however, I've been using it in my business (since once upon a time it was a trustworthy application with useful extensions like FireFTP) and that installation (and plugins) holds four years of information. So Firefox continually deletes my important data (by) messing up (or blocking/or worse: auto-updating) my plug-ins, even crashing my computer as a result. Today Firefox killed FireFTP by (again) autoupdating FireFTP without my permission, and I did my best to disable that nonsense in about:config). Result: none of the (over 100) FireFTP accounts can be logged on to, they suddenly all ask for a password. I do not have the time to to find all of the passwords and reconfigure FireFTP again. How can I undo the mess Firefox created once again? That is, where are the passwords, how do I downgrade? As a side-question, how can I make Firefox behave again? I'm the boss of my computer, not them! How can I once and for-all take back control and completely kill every kind of auto-update feature?

  Read the article

• LDAP SSL connect problem

  - by juergen

  I set up a test domain for my LDAP SSL tests and it is not working. I am using Windows Server 2008 R2 SP 1. I came so far: 1. i generated and installed my self signed certificate on the test domain controller 2. on the server i can log into ldap over SSL with the MS ldp.exe tool. 3. using ldp.exe on a client that is no in this domain the login fails with error 0x51 = "failed to connect". (i don't have a client computer that is in this domain right now) 4. I testet the certificate by using it in the IIS on the test server and I can reach the default page of the test server over SSL. (from the client that is not in the domain) 5. analysing the traffic between client and server I can see that the server is sending a certificate to the client. why isn't this working on my client computer?

  Read the article

• no administrator password for Windows 7

  - by huskergirl78

  I'm a secretary and my boss set up my new Windows 7 OptiPlex 7010 (Dell) computer for me while I was on vacation (he does not remember setting any "administrator" password). We are a small office so there is no system password set, either. I've used it for 6 months, all the while I couldn't access network drives, etc., without an administrator password. It was annoying, but I could still get my work done. Finally, on a slow day I took it upon myself to "fix" the problem, and in all my infinite wisdom, I managed to change my user account from administrator to standard user, so now I really can't do anything. I can't download or install any programs, move or rename files, etc. I tried the Dell suggested solution, but the BIOS tells me there is no password set, so it has to be a Windows 7 problem. All the solutions I have come across require an administrator password to let me do them. What can I do to find out the admin password so I can use my own darn computer!? Is there a default admin password?

  Read the article

• iTunes Home Sharing only works one way between 2 Windows XP PC's on the same LAN

  - by scunliffe

  Both PC's have the latest iTunes installed. PC (A) can "see" that there is a shared library "B library" but attempts to connect to it return this error message: The shared library "{Username}'s Library" is not responding (-3259) Check that any firewall software running on either the shared computer or this computer has been set to allow communication on port 3689. however the reverse works fine. e.g. PC (B) can "see" shared library "A library" and can access all content. Notes: Both PC's have Home Sharing enabled (turned off/on several times to verify). Both PC's have Windows Firewall turned on, but in the exceptions tab, iTunes is allowed, and Port 3689 is also added as a firewall exception (just in case) Both iTunes accounts have been "authorized" on both PC's Both PC's connect via LAN via D-Link DIR-615 router. In the advanced application rules, iTunes has also been added to allow traffic on port 3689 un-hindered. Is there any other magical setting/configuration option that I should be aware of and set in order to get this to work? I could care less about sharing apps etc. I just want the music sharing to work. Update: Solved! It turns out on PC (B) there were multiple accounts set up. 1 of the accounts had the checkbox checked under the Windows firewall "On" option which states "No exceptions" thus even though it was added to the exception list on the main user account, this other account was blocking access.

  Read the article

• Mac dev folder missing, SSH not working

  - by SamGoody

  A few days ago, SSH stopped working. When I try logging in a get the following message: PTY allocation request failed on channel 0 stdin: is not a tty fatal: unrecognized command '' Connection to 74.52.61.194 closed. Web searches have shown me that there might be something wrong with /dev/std. But my computer lacks a /dev/ drive. There is an Alias to /dev/ [hidden, but I've revealed hidden files to do this search], but when I try to open it I am told that it cannot find the folder it is aliasing. Now, many a web search tells me that without a dev folder, the computer doesn't work, but it does seem to work, except the SSH. Also, are there any tools that can save my SSH preferences so that I don't have to, each time, type out the username@adrees, password, path all of which are long and complex? Not looking for a Filezilla type client, there are many of those. Looking for a command line like putty, that lets me use bash on the remote client. Am on Macbook Pro, latest version of Tiger.

  Read the article

• Microsoft Mouse and Keyboard Center - Slow response for App-specific shortcuts

  - by Darrel Hoffman

  So a few months ago, I bought a new MS mouse, and was surprised that they'd discontinued Intellipoint in favor of this Microsoft Mouse and Keyboard Center. It seems to have the same functionality underneath all the bloat, but there's a very serious drawback - when I set up application-specific functions for the extra buttons on the mouse, they work, but sometimes with a very long delay, like up to a minute or more. For example, I often set up the left side button as an "Undo" in various programs for convenience. But sometimes, when I try to use that Undo button, nothing happens, so I'm forced to use the standard Ctrl-Z or whatever. But then, a minute or so later, it suddenly remembers that I hit that button a while back, and calls the Undo unexpectedly on something entirely different. It's infuriating. No modern computer function should be this slow. It's not the software or the computer itself, because doing an Undo via Ctrl-Z or the menu still works instantly. It's very definitely a side-effect of delayed response to the mouse button. Usually after it delays the first time, it'll work quickly after that, but if you haven't used a given shortcut in several minutes, it "forgets" again and you get another inexplicably long delay. Intellipoint never had this problem, but it's not supported any more, and not compatible with the newer mice. Has anyone else noticed slow-downs with MS M&K C and app-specific shortcuts? Any ideas how to get around this? I use these shortcuts extensively in my workflow and it's just entirely unacceptable to have such a long delay in what should be a pretty basic feature.

  Read the article

• Task scheduled to wake laptop - only works when lid is open

  - by JD Pack

  I am running Windows 7 Starter on an Acer Aspire One laptop. I want my laptop to automatically run a task (backup the HDD to a network drive) once a week in the middle of the night. I scheduled the task in "Task Scheduler" and checked the box to wake the computer to run the task. I also changed the advanced power settings to allow wake timers. This was half of the solution. It now works flawlessly when the lid is open... the computer can wake itself up from either sleep or hibernate mode to perform the backup. When the lid is closed however, its sleeping beauty. Any ideas? I don't want to have to remember to open the lid once a week. It sort of defeats the purpose of an "automatic" backup. Update: I discovered that it can wake from sleep (or hybrid sleep), but not from hibernate when the lid is closed. This is good news. I'd still be curious about how to get it to work from hibernate, but I'm pretty happy about waking from sleep at least.

  Read the article

• What can prevent a Server 2008 machine accessing its OWN UNC shares?

  - by Simon

  I need to set up a UNC share for my hosted dedicated server to access a share on itself. Unfortunately TFS requires a UNC share. I am on a Windows Server 2008 Standard SP2 64bit dedicated server behind a PIX 501 firewall hosted with GoDaddy. I just cannot get the server to access itself and get this error: Windows cannot access \\SERVER\SHARE Check the spelling of the name.. etc. I've found numerous questions about this but no answer to my problem. Server 2008 Standard x64 SP2 Workgroup - not domain Windows Firewall is off Computer browser service is on I am trying to access \\MYMACHINE\TFS-BUILDS by typing in - or double clicking. Neither works. Machine has single network card Filesharing wizard says share was ok Share was showing under 'Computer management' Permissions are set to 'everyone' full control No obvious errors in eventlog Reboot didn't fix it Unfortunately I cannot try to access other shares in or out of this machine because it is a hosted dedicated server and the only machine behind a hardware firewall. The only thing left i can think of is that the hardware firewall needs to be configured. I don't think it is this because we have a 2003 Server machine behind a different hardware firewall and that one works fine. What on earth is left?!

  Read the article

• Windows 7 hangs on black screen for a while after log in

  - by steini

  I get the welcome screen. I click on my user and get the "logging on" screen. After that all I get is a black screen with a mouse cursor. I can't even start task manager. No ctrl+alt+del or ctrl+shift+escape. It stays like this for about 10 minutes, then the desktop finally starts loading. According to the hdd led on my case, windows isn't even trying to access the hard drive for that whole time. It's just hanging doing nothing it seems. What I have tried: Uninstalled video driver and removed leftovers with driver sweeper Disabled all startup programs and non microsoft services Loaded "last known good configuration" Ran the alleged "black screen fix" from prevx against my best judgement (don't really like running random exes without knowing what they do at all) None of that works. I can boot into safe mode normally. My specs: i7 920 Gigabyte X58-UD3R Gigabyte HD5870 1GB 12GB Mushkin Silverline 1333MHz Windows 7 Ultimate x64 I'm also having another problem which I suspect is related. After I have gotten the computer up and running, everything works perfectly, but when it's been on for a while it starts behaving strangely when changing display modes. When I start up a game or anything that changes the screen resolution the computer freezes for about a minute every time until I reboot again. I think this is probably related to the black screen problem. Just thought I'd check to see if anyone has had the same problem. Let me know if I should post any more details about my system to help diagnose this. Thanks in advance.

  Read the article

• Network Sharing Issues

  - by Mark Kramer

  I have two computers I want to have on a network share together (so the laptop can print through the desktop's printer). These are both connected to the same router. (One wired and one wireless) And they both have the same workgroup name. However, when I type "net view" in the command prompt, the only computer that shows up is the computer I type the command into. How do I get these computers to be shared with each other? Update: The tower is running Windows XP, the Laptop is running Windows 7. I have disabled the Firewall on both until I get this set up. Update 2: Typing the command net view on my desktop is acting very strangely. Noe sometimes it only shows itself on the list of computers, sometimes it shows itself and the laptop and sometimes it doesn't work at all and displays system error 6118. I typed net view into the command prompt on the Windows 7 laptop and both computers showed up, so I went to connect to the desktop from the laptop and it said the dekptop could not be found, even though it is showing up int he list of shared computers. Here are supporting pictures (these are coming from the laptop)

  Read the article

• iTunes copy just metadata (song and album ratings, playlists) from iPod

  - by Jared Updike

  I have an iPod touch that I synched with my Windows computer (iTunes 9.0 I think) until my harddrive failed and I lost my entire library. I rebuilt the library (songs) from a year old backup (and various other source for songs) but my playlists and ratings are of course a year old. My iPod itself has most of the playlists and ratings I care most about (favorite songs and albums, rated 4 and 5, for example). I have a catch 22 situation where I feel nervous that I haven't backed up my iPod in around 4 months (when my drive failed) so I'd like to back it up as soon as possible... but if I back it up I have to clear all the songs and playlists and copy them back, which I can't really do since I need to rebuild my playlists on my computer first (using the data only available on my iPod!) The question: is there a better way to READ the information off my iPod than doing it manually, song by song and album by album and playlist by playlist (XML, text dump, database, spreadsheet, anything). In other words, mostly I want the information (metadata like ratings and playlists, not songs) copied off the iPod so I can more quickly get my iTunes library ratings and playlists re-built (manually) so I can finally wipe the music and back up my apps, etc. Then I'd like to copy the music back immediately. The part I'd like to avoid is manually navigating everything on my iPod to read through all the playlists and ratings (50 GB, 6,000+ songs) as I re-enter all of that data by hand. I've done a few dozen albums and it's pretty time consuming having to tap around on the iPod. Reading from a spreadsheet (for example, or XML which I could write a script to get into spreadsheet form) would probably help tremendously, plus then I'd have a backup of that information somewhere besides just my iPod.

  Read the article

• Toshiba A205-5804 freezes when plugged in

  - by heron

  Well I have a Toshiba A205-5804 and the problem is that the screen freezes anytime I plug the pc into the external power supply, not as most of the computers having the same issue, my computer DOES freeze in safe mode, and I really can't bear this problem for much longer... It's not an overheating problem, the computer is not getting hot or anything related, I've already tried changing the AC adapter, booting only with AC and no battery, and also all of these suggestions: Try changing the following setting in the bios setup, under the 'Advanced' tab Dynamic CPU Frequency: Mode = Always Low (NOT DYNAMIC) My laptop has been running on AC power without a problem for 24hours, including many restarts, and when I went back to the original bios setting, the problem returned almost straight away. EDIT Other suggestions I found on the web from here and here: Set the power plan to high performance Set the power plan to "Minimal Power Management" (1 and 2 do conflict) Start - Control Panel - Device Manager -- Processor - disable one of two processors - reboot normally 4.Do this: Only plug battery into laptop Turn on the laptop and start Windows normally Plug AC adapter into laptop, the screen will freeze Leave the laptop the way it is for 12-24 hours After 12-24 hours, turn it off the hard way Once it is turned off, turn it back on. The laptop is working now. I have no idea of what can it be...

  Read the article

• Can't start Windows 7 after cloning HDD

  - by Paul

  Brief description: cloned HDD1 - HDD2 HDD1 partition 1 boots HDD1 partition 2 boots HDD2 partition 1 boots HDD2 partition 2 doesn't boot Windows, but is bootable in general Now verbosely: In all the cases computer is the same. I have two Windows 7 installations on HDD1 - both are booting fine. I choose between them using standard Windows 7 boot loader menu. Technically there are 4 partitions: 100 MB Boot loader partition (active), Windows 7 copy 1 (25 GB), Windows 7 copy 2 (150 GB) and Working partition. All are primary. In past few days I tried to clone the whole HDD1 to HDD2 of the same size (but 2,5 inch form factor) as is using Minitool Partition wizard. Everything has been copied, all files are accessible, no faults in file system structure, even boot loader wasn't damaged and I hadn't to repair it. But I can boot only first installation of Windows 7 (it boots without issues). When I choose the second installation, I get immediately a completely black screen without any texts, cursors and other data. HDD isn't accessed after that. This black screen is sensitive to Ctrl-Alt-Delete which causes computer reboot. I did some experimenting: Installed Windows 7 to that partition - it booted fine. Then I renamed "Windows" to "Windows.old" and copied Windows directory from HDD1 as it was, using Far Manager, and got the same troubles - black screen. (Of course I performed renaming and copying from other copy of Windows). So, it seems that problems are inside this installation of Windows, somewhere in its files.

  Read the article

• Host system resets (crashes) when using VMWare or VirtualBox and 64-bit guest systems

  - by sinni800

  I have been trying to install virtual systems on VMWare for a while now and encountered strange behaviour from my PC. The behaviour is as follows: On "automatic" virtualization mode it either outputs a cryptic error message (can MAYBE give later, if I can reproduce) right on startup (before even the BIOS) or it resets the complete HOST system (blackscreen, bios...) If I install a Windows XP on it it works well on "binary translation" mode. If I try installing Linux on it, in "binary translation" mode it crashes 1 or 2 seconds after I hit enter on the GRUB selection screen (after the first page of kernel messages rolled in) Using VirtualBox it crashes right in the BIOS. It gave me a Bluescreen though! 0x00000101: CLOCK_WATCHDOG_TIMEOUT: a clock interrupt was not received on a secondary processor within the allocated time interval NEWS: I tried VirtualBox again and it did not completely crash the computer this time. It gave me a critical error and a log file: http://pastebin.com/yKZSDs91 In conclusion, it will crash instantly if VT-x is activated. If not, it seemingly only crashed if I try to install something with 64 bits. Another update: Yes, it ONLY crashes when the guest is 64 bit! What I tried: Reinstalling Windows (my Windows installation was quite broken so it seemed natural. Didn't work though.) New BIOS What I am certain of: Virtualization extensions are activated in the BIOS What my computer specs are: ASUS P8P67 LE mainboard, newest BIOS/EFI firmware Intel Core i5 2500k Ati Radeon HD 5770 16 GB Corsair 1333mhz DDR3 RAM, 4 X 4 GB

  Read the article

• How is network mounted software executed?

  - by CptSupermrkt

  I would like to understand how network mounted software works. For example, at my place of work, we have a software server. Each client machine (hundreds of them) automatically mounts directories from the software server on boot. For example, a program like Matlab is installed just once on the software server, but each client machine can start up an instance of Matlab. What is going on under the hood? Let's say I run /opt/bin/matlab and /opt/ is mounted from the software server, what happens when I press Enter to execute matlab on a client machine? The process is on the client machine, and I've already narrowed down that there isn't any implicit or hidden file transfer (i.e. copying matlab to my machine temporarily for that session) by running matlab on a computer with nearly zero disk space (i.e. not enough room to transfer). Since Matlab was installed on the server, how is my client computer executing it? What mechanism is controlling this? What is happening behind the scenes?

  Read the article

• Notebook display problem (multiplication)

  - by SubniC

  Hi, I'm having some troubles with the display of a LG E500 notebook. The thing is that without any known reason the display starts to show the screen divided in eigth parts and each part show the display image as if I had a matrix of eigth displays :) I thought it could be some kind of refresh rate problem or driver related, but it is happening at boot-up as well and the BIOS. I got the computer completely unassambled yesterday and I check all the wires and connectors looking for something broken or unconected, but without luck... You can see a picture here of the problem (sorry for the low quality, but I think it illustrate the problem. EDIT 1: I uploaded a new pictrue, here you cans ee the problem better :) There are three horizontal lines that you can see just between the windows. You can see the grey line at the first moment you turn on the computer and the after the duplicated screens show up just like if they where arranged over a grid (over the horizontal lines...) I hope it makes any sense. Do you know what could be happening? or can you tell me what would you do? Thank you very much for your help.

  Read the article

• OS X won't boot up unless I hold down option key

  - by Gazzer

  I have a strange issue on an early 2008 Mac Pro running OS 10.6: if I restart the computer it restarts normally if I shutdown and boot, it stops at the grey screen just before the boot process if I shutdown and boot but hold down the option key, I can select the boot disk and all is good. I've just cloned the disk, and the same thing happens. The disk is a SAMSUNG HD154UI The disk is partitioned (the second partition holds a clone of the Snow Leopard Install disk) One weird thing on the original disk was one of the partitions said 'EFI Boot' in a non-aliased font rather than the name of the disk when the disks are listed upon holding down option. Solution: it seems that there was a problem with the disk. Part of the difficulty in finding the solution was that you need to remove the disk from the computer completely. For example, a good disk in Bay 3, wouldn't boot up if the bad disk was in Bay 2. So for ages I thought the problem was hardware related in Bay 3. So if you think you have a dodgy disk remove it totally if you are testing the hardware with a 'clean' disk. Cleaning the PRAM helped to get the new disk to work too.

  Read the article

• USB drive was bootable, but no longer boots

  - by i-g

  I'm trying to install a new OS onto a computer from a bootable USB stick. I previously installed Ubuntu Linux and it was a piece of cake -- I downloaded the ISO image, used UNetbootin to copy it to the USB drive and make it bootable, and that was that. Now, however, no matter what I try, I can't make the same USB drive bootable again! I've tried formatting it as FAT32 and NTFS. I've tried several different Linux distributions and Windows 7. I've tried using UNetbootin, Windows 7 USB Download Tool, WinToFlash, and manually making it bootable with diskpart/bootsect/bootrec. (Yes, I've tried bootsect /nt60 x: /force.) None of this seems to be working! When I try to boot from the drive, the machine reads from it (I can see the drive's LED blinking) and then gives me the same "Insert system disk and press Enter" message. (I've disabled booting from the hard drive.) Am I missing something I need to do to make the USB drive bootable again? I think it lost some pixie dust when I formatted it with the standard Windows formatting tool (it was quicker than deleting files), but I have no idea what it was or how to get it back. The USB drive in question is a SanDisk Cruzer 8GB SDCZ6. The computer I'm working on is running Windows Vista SP1.

  Read the article

< Previous Page | 249 250 251 252 253 254 255 256 257 258 259 260  | Next Page >