Search Results

Search found 8268 results on 331 pages for 'difference'.

Page 254/331 | < Previous Page | 250 251 252 253 254 255 256 257 258 259 260 261  | Next Page >

• Should I use "Raid 5 + spare" or "Raid 6"?

  - by Trevor Boyd Smith

  What is "Raid 5 + Spare" (excerpt from User Manual, Sect 4.17.2, P.54): RAID5+Spare: RAID 5+Spare is a RAID 5 array in which one disk is used as spare to rebuild the system as soon as a disk fails (Fig. 79). At least four disks are required. If one physical disk fails, the data remains available because it is read from the parity blocks. Data from a failed disk is rebuilt onto the hot spare disk. When a failed disk is replaced, the replacement becomes the new hot spare. No data is lost in the case of a single disk failure, but if a second disk fails before the system can rebuild data to the hot spare, all data in the array will be lost. What is "Raid 6" (excerpt from User Manual, Sect 4.17.2, P.54): RAID6: In RAID 6, data is striped across all disks (minimum of four) and a two parity blocks for each data block (p and q in Fig. 80) is written on the same stripe. If one physical disk fails, the data from the failed disk can be rebuilt onto a replacement disk. This Raid mode can support up to two disk failures with no data loss. RAID 6 provides for faster rebuilding of data from a failed disk. Both "Raid 5 + spare" and "Raid 6" are SO similar ... I can't tell the difference. When would "Raid 5 + Spare" be optimal? And when would "Raid 6" be optimal"? The manual dumbs down the different raid with 5 star ratings. "Raid 5 + Spare" only gets 4 stars but "Raid 6" gets 5 stars. If I were to blindly trust the manual I would conclude that "Raid 6" is always better. Is "Raid 6" always better?

  Read the article

• Postfix character encoding?

  - by Camran

  I use Postfix as a mailserver. I have Ubuntu OS. Then I use PHP to send emails. Problem is that none of my emails are encoded properly by a mailsoftware which my VPS provider uses. According to them, the problem lies with me. It is only the name field which isn't encoded properly. For example "Björn" becomes "Björn" in my emails. However, when I echo the $name, it outputs "Björn" which is correct. Also, gmail and hotmail does show it correctly. The strange part is that the "text" (the message itself) is encoded properly. I use the following for sending mail: $headers="MIME-Version: 1.0"."\n"; $headers.="Content-type: text/plain; charset=UTF-8"."\n"; $headers.="From: $name <$email>"."\n"; $name= iconv(mb_detect_encoding($name), "UTF-8//IGNORE//TRANSLIT", $name); //// I HAVE TRIED WITH AND WITHOUT THE LINE ABOVE, NO DIFFERENCE mail($to, '=?UTF-8?B?'.base64_encode($subject).'?=', $text, $headers, '[email protected]'); I have tried with and without the iconv line also, no luck. The last thing I can think of is POSTFIX, could there be a setting for character encoding there? Anybody knows?

  Read the article

• Internal Code Signing: Key Distribution, or Certificate Server?

  - by Myrddin Emrys

  I should first note that we have nobody in IT with significant familiarity with self-signed certification. We have a moderately sprawling network (one forest, many locations), and we are now rolling out internal code signing; until now users have run untrusted code, or we even disabled(!) the warnings. Intranet applications, scripts, and sites will now be signed with self certification. I am aware of two obvious ways we can deploy this: Distributing the keys directly via a group policy, and setting up a cert server. Can someone explain the trade-offs between these two methods? How many certs before the group policy method is unwieldy? Are they large enough that remote users will have issues? Does the group policy method distribute duplicates on every login? Is there a better method I am not aware of? I can find a lot of documentation on certifications and various ways to create them, but I have not been able to find something that summarizes the difference between the distribution methods and what criteria make one or the other superior.

  Read the article

• How to connect 2 routers (Asmax and D-link)

  - by piobyz

  I just bought a new router, D-link DSL 2641B and want to connect it to another one, provided by my ISP, Asmax AR 804MP. Previously, I had Linksys WRT350N, and there was no problem, while I had Ethernet cable plugged in to one of LAN ports in Asmax and INTERNET(RJ45) port in Linksys, connection used PPPoE protocol -- worked OK. D-link has DSL(RJ11) port (which I don't want to use as Asmax replacement, while there is a separate Ethernet cable with a TV plugged to Asmax, which I don't want to configure from scratch on D-link). How should I connect my new D-link to work with Asmax? Via DSL port? Via one of the LAN ports (in which case I probably should change the purpose of this port in the config, I guess?). I tried connecting D-link both ways: LAN(ASMAX) to LAN(DLINK) LAN(ASMAX) to DSL(DLINK) (using RJ11 - RJ45 cable) I hope there is some setting in the DLINK's config that I overlooked. I haven't tried to see what's in ASMAX's config, but I guess I don't need to change anything there, while Linksys worked just fine? The only difference I see, is that D-link has RJ11 DSL port as WAN, and Linksys has RJ45 (called by them INTERNET) as a main WAN port.

  Read the article

• Denying access to website via htaccess based on http header

  - by neekster

  I've been trying for ages to get this to work and I can't put my finger on it. What I'm trying to do is block access to a site from a number of countries, based on the CF-IPCountry header added by CloudFlare. I figured htaccess was a suitable way to do this. We are running LiteSpeed 4.2.4 on top of DirectAdmin for a control panel. The problem we having is the htaccess rule doesn't seem to do anything. Here's the rule we tried: SetEnvIf CF-IPCountry AU UnwantedCountry=1 Order allow,deny Deny from env=UnwantedCountry Allow from all That makes no difference at all, connections are still accepted. Just to check that the rule was at least being processed, I changed Allow from all to Deny from all, and connections were refused. So it appears to be a problem wit the variable. Here's the relevant headers that come in with the request. Connection: Keep-Alive Accept-Encoding: gzip CF-Connecting-IP: xx.xx.xx.xx CF-IPCountry: AU X-Forwarded-For: xx.xx.xx.xx.xx CF-RAY: c9062956e2d04b6 X-Forwarded-Proto: http CF-Visitor: {"scheme":"http"} Zone-Name: xx.com.au Hopefully someone can help me out, this has been driving me nuts for too long. Thanks

  Read the article

• ATI firepro will not detect a second DVI-D monitor

  - by John

  OK so weird issue here. I have previously been running 6 screens off of 3 of the older ATI firepro graphics cards but they had a problem with the heat sink getting too hot and warping the PCB resulting in total failure of the card, to replace my three dead cards I purchased a new-type ATI firepro with the newer heat sink design. I'm only using one at the moment to make sure they've fixed the problem before I waste more money on 2 more cards but this is where things start to get weird. The Firepro's only have one port on them, they connect to two monitors via a splitter cable going from the one port to two DVI connectors for the screens. When I plug two identical monitors in via their DVI inputs not matter what I do windows and Catalyst will only detect one screen. However if I use the VGA input on one of the screens with a VGA - DVI adaptor to plug it in to the card it works fine. This confuses me greatly. I'm currently using the ATI Firepro 2270 Graphics card with identical DELL U2311H screens. I can post the rest of the system spec as well if needed but I wouldn't have thought it would make much difference as it had no problem handling 6 screens before the graphics cards failed. Naturally both catalyst and ATI drivers are the most current version. ATI tech support has been absolutely zero help, they seemed to get stumped as soon as I verified that both screens were plugged in and connected properly. Anyone have any ideas?

  Read the article

• Load balancing with puppet

  - by Gonçalo Queirós

  Hi there. Im trying to setup a loadbalancing system. My load balancer (nginx) has a conf file where i should list all IP's of the upstream servers. I could put the IP's on the conf manually, but this ways i would need to change the conf file every time i add/remove an upstream server. For now i came up with two different ideas, but i don't like much of neither: 1 - Have every upstream machine to use Exported Resources to create a file with it's IP..Then the load balancer server will have an "include conf_directory/*", and load all the files created by the upstrem servers. Since the load balancer is using nginx this can be done, but if i wan't latter on to configure something that doesn't have the "include" on the conf files, this solution will not work. 2 - If the config doesn't support the "include" command, then we could have again, every upstream server use the Exported Resources to create a filw with its IP, and latter on, the load balancer execute a command that would pick every file and generate the config Both versions addopt the same techinque, the difference is that version 2 is used when the server (that needs to have a conf generated) doesn't recognize a command like "include" inside its own conf. Now, my question is, is there any way to do this in a different form? I suspect that there is, since puppet is made to manage multiple servers, it seems a bit strange not have a easy way to configure load balancers.

  Read the article

• Erratic WiFi 2.4 GHz channel spikes, what gives?

  - by Francis W. Usher

  Sorry guys, first a gripe about my neighbor's WiFi access point (it is related): they totally hog the center nine 2.4 GHz channels (3-11), centered right at 7! I know the outer regions of the signal don't make as much of a difference, and technically they're running channels 5 & 9. Anyway, their signal is clearly interfering with mine, which is necessarily centered at 3 or 11 to evade their interference. I guess it's somewhat a case of access point envy: they happen to have both a stronger signal and a higher data rate, while occupying twice the band width that I do. Getting to the point, I've noticed that they tend to sit nice and pretty centered at 7, but they definitely auto-select their channel, and I've noticed that the auto-selection algorithm tends to shift towards the higher channels; hence I decided to pick channel 3, and I don't get so many intermittent lag spikes any more. Anyway, the thing that weirded me out was the reason they have to auto-select sometimes: unexplained, powerful (talking order of 0dB here), giant spikes of 2.4 GHz activity in consistent regions of the spectrum. I don't think it's just noise, since my wireless monitoring software is registering a MAC address, a manufacturer, and usually a fairly coherent ascii name... and it seems to be a fairly well-confined signal. But these signals are fairly common, and they do some weird stuff to my signal. So my question is what are these signals? Where are they coming from? Where are they going? Why are they so ridiculously strong? Why don't they ever last very long? Here's an inSSIDer screenshot I took, for your perusal. I am labeled with "me", my greedy neighbor labeled with "neighbor", and the 2 quasar signals are labeled with "WTF?".

  Read the article

• Why is writing to my external hard drive slow, while benchmarks show fast writing?

  - by matix2267

  I have an iOmega eGo 320GB portable drive connected through USB2.0 to my laptop running Windows Vista. It's been working fine for quite some time until recently it became very slow when writing e.g. when copying ~300MB movie over to the drive at first it is extremely fast but it actually doesn't write it only puts in cache and then hangs on last 10-20MBs for about a minute. When copying larger files it's the same story: starts fast but then slows down to ~5MB/s (sometimes even slower down to 2MB/s). Strange thing is that I have always had caching disabled for this drive (it was disabled by default and I never bothered changing it). At first I thought that the disk is dying so I checked S.M.A.R.T. values and everything is fine there. I also run chkdsk and it seemed to fix the problem - it worked fast for a few minutes but then it slowed down again. I also tried plugging it into another USB port - no difference. Additionally I noticed that reading under certain circumstances is sometimes slower e.g. loading times for some games are ~10 times longer, whereas simple copying files from this drive to my internal HDD is fast. I ran a speed benchmark using CrystalDiskMark with a 5x100MB run and strangely got these results: read write (MB/s) Seq 33.05 28.25 512k 17.30 15.27 4k 0.267 0.372 4kQD32 0.510 0.260 This is different from what most other people have (I've found many threads about slow disk write while googling but all of them were slow on benchmarks too) which is why I decided to post this problem here. BTW most of the time when writing (or sometimes reading) the activity led is mostly idle (blinks a while and then stops for longer, sometimes has slower blinks ~1 sek, sometimes goes off for a few seconds - extremely long blink :) ) but when benchmarking, defragmenting or just reading (copying from this drive, installing apps from installers there, watching HD videos) it is blinking really fast (like it should) and there are no slowdowns. It shouldn't be driver issue unless stock Windows drivers have some issues I'm not aware of.

  Read the article

• Freebsd jail for an small company - checklist - what shouldn't forget

  - by cajwine

  Looking for an checklist for an "small company freebsd/jail server". Having pretty common starting point: FreeBSD jail (remote/headless) for the company: public web, email, ftp server, and private (maybe in the future partially public) wiki (foswiki) 4 physical persons, (6 email addresses) + one admin - others will never use ssh) have already done usual hardening on the host side (like pf, sshguard etc). my major components are: dovecot, exim, apache22, proftpd, perl5.14. Looking for an checklist, what I shouldn't forget. My plan: openssl self-signed certificates for exim, dovecot and proftpd (wildcard keys) openssl self-signed certificate for apache (later will go for "trusted-signed" key) My questions are: is is an "good practice" having one pair of wildcard SSL-certificates for many programs? (exim, dovecot, proftpd) - or should I generate one key for each service? should I add all 4 persons as standard (unix) users, or I should go with virtual users? Asking because: have only small count of users, and it is more simple to configure everything (exim, dovecot) for local users ($HOME/Maildir), plus ability to set $HOME/.forward/vacation and etc. is here some (special) things what I should consider? (e.g. maybe, in the future we want setup our own webmail - will make this any difference?) any other recommendation? Thank you, hoping that this question fit into the http://serverfault.com/faq under the: Server and Business Workstation operating systems, hardware, software Operations, maintenance, and monitoring Looking for an checklist, but please explain why you're recommending it. See Good Subjective, Bad Subjective. related: What's your suggested mail server configuration for a FreeBSD server?

  Read the article

• Two monitors with Mac Mini - one displays black despite receiving a signal

  - by alex

  My Mac Mini outputs to my two new monitors - Dell U2311Hs. The LED on the bezel displays blue when receiving a signal, or yellow otherwise. Both screens are displaying blue. It also seems my Mini can see both of them... However, one of them is black. It just displays black, but appears to be receiving a signal (when I turn the Mac off, it then displays No Signal). To make things weirder, on startup, the boot up (white with Apple logo) appears on the right monitor (the one that now displays black). Occasionally, it flickers up on the black screen for 1 second. I have tried Detect Displays. It appears to do nothing. I'm also running a dual monitor KVM. Video connections are DVI-D. How can I fix this situation? Thanks. Update This is the weirdest thing - I used the DVI-D cable that came with the KVM and it seems to have fixed it - I didn't both because it looks identical to any other DVI cable (in form an pin out). So, I will accept an answer if someone can tell me what may be the difference in these cables?

  Read the article

• SQL Server Instance login issue

  - by reallyJim

  I've just brought up a new installation of SQL Server 2008. I installed the default instance as well as one named instance. I'm having a problem connecting to the named instance from anywhere besides the server itself with any user besides 'sa'. I am running in mixed mode. I have a login/user that has a known username. Using that user/login, I can properly connect when directly on the server. When I attempt to login from anywhere else, I recieve a "Login failed for user ''", with Error 18456. In the log file in the server, I see a reason that doesn't seem to help: "Reason: Could not find a login matching the name provided.". However, that user/login DOES exist, as I can use it locally. There are no further details about the error. Where can I start to find something to help me with this? I've tried deleting and recreating the user, as well as just creating a new one from scratch--same result, locally fine, remotely an error. EDIT: Partially Resolved. I'm now passed the base issue--the clients were trying to connect via the default instance. I don't know why. So, once proper ports were opened in the firewall, and a static port assigned to the named instance, I can now connect--BUT ONLY if I specify the connection as Server,Port. SQLBrowser is apparently not helping/working in this case. I've verified it IS running, and done a stop/restart after my config changes, but no difference yet.

  Read the article

• Exchange 2010 Transport rules stepping on each other

  - by TopHat

  I have a group of users that I have to restrict email access for and so far using Exchange Transport Rules has worked very well. The problem I am having is that Rule 0 is supposed to bcc the email to a review mailbox but otherwise not change anything and Rule 9 is supposed to block the email and throw a custom NDR to tell the user why they were blocked. Here are my results in practice however. If Rule 0 is enabled and Rule 9 is enabled then only Rule 9 functions If Rule 0 is disabled and Rule 9 is enabled then Rule 9 functions If Rule 0 is enabled and Rule 9 is disabled then Rule 0 functions This is after the Transport Service has been restarted (multiple times actually). I have other rule pairs that work correctly. None of these are overlapping rulesets however. - copy email going to address outside domain and then block - copy email coming in from outside and then block Here is the rule for copying internal emails (Rule 0): Apply rule to messages from a member of Blind carbon copy (Bcc) the message to except when the message is sent to a member of or [email protected] Here is the rule to block the same email (rule 9): Apply rule to messages from a member of send 'Email to non-supervisors or managers has been prohibited. Please contact your supervisor for more information.' to sender with 5.7.420 except when the message is sent to , [email protected], The distribution group used for membership in these rules is used for the other blocking and copying rules and works as expected. Is there something I missed in this setup? All of the copy rules are at the front of the transport rule group and all the actual copies at at the end of the queue if that makes a difference. Any thoughts as to why the email doesn't get copied when it gets blocked?

  Read the article

• Administrative shares in Windows 7 Pro not visible

  - by Chris Tybur

  My desktop machine has a clean install of Windows 7 Professional. For some reason the standard administrative shares Admin$, C$, D$, etc are not visible, either in Computer Management - Shared Folders - Shares or via net share. I also have a laptop with a clean install of Windows 7 Professional, and I can see the admin shares in both places. As such, I can map to \\laptop\c$ from the desktop, but I can't map to \\desktop\c$ from the laptop. I pretty much took the defaults during the Windows 7 installations. I've tried adding LocalAccountTokenFilterPolicy to the registry on the desktop, but that didn't work. On the desktop I've also disabled UAC, turned off Windows firewall, removed it from a homegroup, made sure file and printer sharing is turned on, but nothing has worked. There is some subtle difference between the two machines that I can't seem to find. I'm logging into both machines using a local account that is in the Administrators group. Both accounts have the same name and password. I really don't want to have to create a new share for the desktop's C drive, especially since C$ is visible and working on the laptop and therefore I should be able to make it work on the desktop. Any idea why the admin shares would work on one machine and not another? Or why LocalAccountTokenFilterPolicy would fail?

  Read the article

• What's going on with traceroute?

  - by Kevin

  The following is what happens when I run traceroute from a certain location: # traceroute google.com traceroute to google.com (74.125.227.39), 30 hops max, 60 byte packets 1 gateway.local.enactpc.com (10.0.0.1) 0.138 ms 0.101 ms 0.084 ms 2 * * * 3 * * * 4 * * * 5 * * * 6 * * * 7 * * * 8 * * * 9 * * * 10 * * * 11 * * * 12 * * * 13 * * * 14 * * * 15 * * * 16 * * * 17 * * * 18 * * * 19 * * * 20 * * * 21 * * * 22 * * * 23 * * * 24 * * * 25 * * * 26 * * * 27 * * * 28 * * * 29 * * * 30 * * * Absolutely nothing of interest... Now, originally I thought this was just a fact of the location's network set up. (I assume they block pings or something...) However, watch what happens when I use nmap to run a traceroute... # nmap -sP --traceroute google.com Starting Nmap 5.21 ( http://nmap.org ) at 2012-09-25 22:18 CDT Nmap scan report for google.com (74.125.227.40) Host is up (0.034s latency). Hostname google.com resolves to 11 IPs. Only scanned 74.125.227.40 rDNS record for 74.125.227.40: dfw06s06-in-f8.1e100.net TRACEROUTE (using proto 1/icmp) HOP RTT ADDRESS 1 0.19 ms gateway.local.enactpc.com (10.0.0.1) 2 1.93 ms 99-20-92-1.lightspeed.austtx.sbcglobal.net (99.20.92.1) 3 25.61 ms 99-20-92-2.lightspeed.austtx.sbcglobal.net (99.20.92.2) 4 ... 6 7 23.68 ms 12.83.68.137 8 31.30 ms gar23.dlstx.ip.att.net (12.122.85.73) 9 ... 10 31.82 ms 72.14.233.65 11 32.27 ms 209.85.250.77 12 32.98 ms dfw06s06-in-f8.1e100.net (74.125.227.40) Nmap done: 1 IP address (1 host up) scanned in 3.29 seconds When using nmap I get A LOT more results than with traceroute, why? Note, I checked, and the difference in target IP addresses is not related...

  Read the article

• windows 7 turns off itself everyday at about 9am

  - by Radek

  I was given this comp at work and after a week or so this strange thing started to happen in the middle of doing something :-( It turns off itself at about 9.10am every morning Just once a day and it works fine after it had it little nap. it happens both if the comp was on all night or I turned it off before leaving the office. I tried to swapped the memory as I was told that there was an issue with memory. But moving or removing any memory did not make any difference. I am not aware that I would install any program that could cause that. I installed AVG and set it up to do every day scan about 8am + if restart is needed it requires user confirmation. 'The Software Protection service has stopped' few minutes before it turned off itself but it happened also at other times without the computer turned off. I turned off Windows automatic updates as the first thing when I got the comp configuration Windows 7 Ultimate Intel Core2 Quad Q9550 at 2.8GH, 8GB RAM ST31000528AS Barracuda 7200.12 SATA 3Gb/s 1TB Update Below message are logged when I turn the comp on again. Message 1: The previous system shutdown at 9:08:54 AM on ?6/?29/?2010 was unexpected. Message 2: Level:Critical Source: Kernel Power EventID 41 Task Category (63) The system has rebooted without cleanly shutting down first. This error could be caused if the system stopped responding, crashed, or lost power unexpectedly. Log after manual restart Update 2 (task scheduler)

  Read the article

• File Open/Save Dialog always 'Not Responding'

  - by Amanda

  I am aware that this question has been asked once, however the solution for them didn't work with me. Whenever I go to open/save a file in any program, the dialog does not come up, and the application goes to 'Not Responding'. This goes on for about a few minutes, and then stops, but still does not open the dialog. There have been a few occasions where the dialog has suddenly worked for a while, but then the problem comes back. I have tried many solutions given around the internet, I have cleaned it with CCleaner, disk defragged it, sorted the index. Nothing works. Is there anybody who has any idea what the problem is? This is Windows Vista. I'm not quite sure what kind of information you guys would need about my laptop, but I'll give you it if you need it. :) Solutions I have Tried: I have tried deleting the 'Shellicon' folder in the registry, which wasn't even in there. I have looked for mapped network drives lingering around, and I haven't come across any. I have tried rebuilding teh Widnows Search Indexes...no difference.

  Read the article

• Internet Troubles - PPPoE vs PPPoA?

  - by AkkA

  I have been having some internet troubles at home (ADSL2+ connection in Australia). We get random drop-outs from the authentication connection. It will keep the connection to the DSL service, but we lose authentication and either have to restart the router/modem (its combined, a Belkin one, not sure on model number) or unplug the phone cable, wait about 30 seconds and plug it in again. I've called the ISP (Telstra) a few times, but they only offer limited support when we dont use their supported hardware. Apparently something had happened on their side, they checked the box again (at least it sounded that simple), and told me it would be fine. It wasnt. I've replaced all the filters around the house, but that didnt help either. We do live a little bit away from the exchange (get a sync speed of about 3000/900), so I thought it could be due to line noise but that hasnt helped. Telstra allow both PPPoE and PPPoA connections (which I'm configuring through my router, dont have software on the PC side). I've been running PPPoA the whole time, would it make any difference changing it to PPPoE? If not, are there any other theories as to why we would be experiencing these drop-outs? It has been fine for at least 12 months, then suddenly started about 2 months ago.

  Read the article

• i7 Windows 7 laptop or Macbook Pro 15" (For making 3D model and Animation)

  - by sppdhs

  Hi everyone, I'm thinking of buying a new laptop as my current one will be 5 years old next year and it currently gives me a blue screen everytime I run a heavy software to make 3D models and animation. Question is: Should I buy Macbook Pro or a Windows 7 laptop? I tried to research and some say that Windows would be better, especially because you can buy a very high spec laptop with cheaper price. While some other say Macbook Pro is the better choice as it can run bootcamp with windows 7 100% performance on every software even though it's a mac. Is this true? Which one is actually better? Btw, the software that I usually use is 3Ds Max, Maya, and ZBrush. To note as well, I have never used a Mac before. I've checked around some stores and budget wise, I'll need around AU$3000+ to buy a Macbook pro, and AU$2000+ to buy a windows laptop. Quite a big difference in price range. Thanks in advance for your help.

  Read the article

• Only tunnel certain applications via OpenVPN

  - by jinjin

  Hi, I've purchased a VPN solution, it works correctly when I have "redirect-gateway def1" in the configuration file (routing all traffic through the VPN). However when I remove that line from the configuration file, I am still able to ping-out of the machine (ping -I tap0), however I cannot ping the IP assigned to the machine (it's a public ip), i get the error: Destination Host Unreachable. I only want to have certain applications sending traffic through the VPN tunnel (eg: ZNC, irssi), all of which i can select which IP they use. However they can't recieve any data, making the tunnel essentially useless to me when disabling redirect-gateway. Any ideas on how to allow specific applications use the tunnel, without of forcing everything to go through it? My configuration file is as follows: dev tap remote #.#.#.# float #.#.#.# port 5129 comp-lzo ifconfig #.#.#.# 255.255.255.128 route-gateway #.#.#.# #redirect-gateway def1 secret key.txt cipher AES-128-CBC The output of ifconfig -a when the tunnel is connected: tap0 Link encap:Ethernet HWaddr 00:ff:47:d3:6d:f3 inet addr:#.#.#.# Bcast:#.#.#.# Mask:255.255.255.255 inet6 addr: <snip> Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:612 errors:0 dropped:0 overruns:0 frame:0 TX packets:35 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:25704 (25.1 KiB) TX bytes:6427 (6.2 KiB) EDIT: the Bcast:#.#.#.# (ifconfig) is different from route-gateway #.#.#.# (openvpn) if that makes any difference.

  Read the article

• How to scan multiple pages from a book under Linux?

  - by rumtscho

  I want the process to look like: I choose the correct scan settings (dpi, color depth, etc) I lay the first page on the scanner and trigger the process The scanner scans the page and waits for me to position the next page correctly I confirm that the next page is ready for scanning Repeat the above two steps until I tell the scanner that there are no more pages to come The scanner saves everything into a single PDF. I tried both xsane and gscan2pdf. First problem: they want me to know how many pages will be scanned. This is already a nuisance, but I can do the counting if needed. The main problem is that in step 3, the scanner does not pause. It is probably optimised for being fed loose sheets. The next scan process is triggered automatically as soon as the CCD has returned to the start position. The time the scanner needs to return the CCD is very short and I can't turn the page and position the book properly. Is there a software which can do the scan process in the way I described above, or did I just miss a setting available in xsane or gscan2pdf to make the scanner pause? If it makes any difference, the scanner is an Epson Stylus SX620FW, I run it using the manufacturer-provided driver.

  Read the article

• How to convert JPEG JFIF files to JPEG Exif format?

  - by tigrou

  I recently put the SD card of my camera in a Windows 7 PC and start browsing pictures on it. I noticed some were not aligned correctly and use rotate feature included in Windows Photo Viewer in order to view them as I wanted. What I didn't know is that when rotate feature is used, it also overwrite the picture when pressing next or previous button resulting in a possible loss of quality (which is in my opinion a bad idea, app should at least warn user of what will happened when using such a feature). After that, I re-inserted the SD card back in my camera and bad surprise happened : the rotated picture could not be previewed anymore. Instead, i got a black screen saying "Incompatible JPEG format". Other files (untouched) are still working ok. To try to understand what happened I opened a JPEG file from camera and one generated on windows 7 in a hex editor. Here is the difference : The camera JPEG files have a Exif tag in them (with 0xE1 in header). Other JPEG files (Windows 7) have first a JFIF tag in it, followed by a Exif tag (with 0xE0 in header). So if i understand it well, both are JPEG files, but using a different internal format. Here is my question : is it possible (using some tool) to convert JFIF files to Exif format ? I understand that original camera files have been reencoded and thus lose some quality (getting originals back is impossible). What i want know if convert them from JFIF back to Exif (without a second loss of quality if possible...)

  Read the article

• Why does my microwave kill the Wi-Fi?

  - by Ohlin

  Every time I start the microwave in the kitchen, our home Wi-Fi stops working and all devices lose connection with our router! The kitchen and the Wi-Fi router are in opposite ends of the apartment but devices are being used a little here and there. We've been annoyed by the instability of the Wi-Fi for some time and it wasn't until recently we realized it was correlated to microwave usage. After some testing with having the microwave on and off we could narrow down the problem to only occurring when the router is in b/g/n mode and uses a set channel. If I change to b/g mode or set channel to auto then there is no problem any more...but still! The router is a Zyxel P-661HNU ("802.11n Wireless ADSL2+ 4-port Security Gateway" with latest firmware) and the microwave is made by Neff with an effect of 1000W (if this information might be useful to anyone). There is an "internet connection" light on the router and it doesn't go out when the interruption occurs so I think this is only an internal Wi-Fi issue. Now to my questions: What parts of the Wi-Fi can possibly be affected by the microwave usage? Frequency? Disturbances in the electrical system? How can setting Auto on channels make a difference? I thought the different channels were just some kind of separation system within the same frequency spectrum? Could this be a sign that the microwave is malfunctioning and slowly roasting us all at home? Is there any need to be worried? Since we were able to find router settings that cooperate well with our microwave's demand for attention, this question is mainly out of curiosity. But as most people out there...I just can't help the fact that I need to know how it's possible :-)

  Read the article

• Terminal emulation has stopped working. Garbage escape chars

  - by oligofren

  To enable me to do some remote administration of our servers I started using a terminal emulation program called TouchTerm Pro on my iPhone. While not the smoothest experience, it has allowed me to leave my computer behind when going out of town, which makes the slightly painful experience worthwhile. As of late, the app unfortunately no longer works. Pressing up and down keys after logging on via ssh gives me garbage like ^[[A and ^[[B. Combinations with Ctrl - like you can see in the video - no longer works either. Writing full command lines and executing by the enter key works though. Being able to search my bash history was the difference between a usable app and endless frustration, so getting it to work is essential. The app has (of course) met its end of life, not getting updated anymore. I am not quite sure, which side (client or server) that has to be "fixed"/hacked to make the control sequences work again. But is there something I can do to make it work as intended? You can see a video of TouchTerm in operation here.

  Read the article

• Anonymous Login attemps from IPs all over Asia, how do I stop them from being able to do this?

  - by Ryan

  We had a successful hack attempt from Russia and one of our servers was used as a staging ground for further attacks, actually somehow they managed to get access to a Windows account called 'services'. I took that server offline as it was our SMTP server and no longer need it (3rd party system in place now). Now some of our other servers are having these ANONYMOUS LOGIN attempts in the Event Viewer that have IP addresses coming from China, Romania, Italy (I guess there's some Europe in there too)... I don't know what these people want but they just keep hitting the server. How can I prevent this? I don't want our servers compromised again, last time our host took our entire hardware node off of the network because it was attacking other systems, causing our services to go down which is really bad. How can I prevent these strange IP addresses from trying to access my servers? They are Windows Server 2003 R2 Enterprise 'containers' (virtual machines) running on a Parallels Virtuozzo HW node, if that makes a difference. I can configure each machine individually as if it were it's own server of course... UPDATE: New login attempts still happening, now these ones are tracing back to Ukraine... WTF.. here is the Event: Successful Network Logon: User Name: Domain: Logon ID: (0x0,0xB4FEB30C) Logon Type: 3 Logon Process: NtLmSsp Authentication Package: NTLM Workstation Name: REANIMAT-328817 Logon GUID: - Caller User Name: - Caller Domain: - Caller Logon ID: - Caller Process ID: - Transited Services: - Source Network Address: 94.179.189.117 Source Port: 0 For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. Here is one from France I found too: Event Type: Success Audit Event Source: Security Event Category: Logon/Logoff Event ID: 540 Date: 1/20/2011 Time: 11:09:50 AM User: NT AUTHORITY\ANONYMOUS LOGON Computer: QA Description: Successful Network Logon: User Name: Domain: Logon ID: (0x0,0xB35D8539) Logon Type: 3 Logon Process: NtLmSsp Authentication Package: NTLM Workstation Name: COMPUTER Logon GUID: - Caller User Name: - Caller Domain: - Caller Logon ID: - Caller Process ID: - Transited Services: - Source Network Address: 82.238.39.154 Source Port: 0 For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp.

  Read the article

< Previous Page | 250 251 252 253 254 255 256 257 258 259 260 261  | Next Page >