Search Results

Search found 29093 results on 1164 pages for 'network interface'.

Page 255/1164 | < Previous Page | 251 252 253 254 255 256 257 258 259 260 261 262  | Next Page >

• How do I block requests to Apache on a network interface?

  - by Dmitry Dulepov

  The problem: I have a local Apache instance on my Macbook Pro. I need it to listen on all network interfaces except en0 and en1 (basically, listen on lo and vnicX from Parallels). I know about "Listen *:80" but this is not a solution in this particular case. The only thing I could imagine if to use OS X firewall to block incoming requests to Apache on those interfaces. But I could not find any working examples and could not make such rules myself. Could somebody help, please?

  Read the article

• Inbound SIP calls through Cisco 881 NAT hang up after a few seconds

  - by MasterRoot24

  I've recently moved to a Cisco 881 router for my WAN link. I was previously using a Cisco Linksys WAG320N as my modem/router/WiFi AP/NAT firewall. The WAG320N is now running in bridged mode, so it's simply acting as a modem with one of it's LAN ports connected to FE4 WAN on my Cisco 881. The Cisco 881 get's a DHCP provided IP from my ISP. My LAN is part of default Vlan 1 (192.168.1.0/24). General internet connectivity is working great, I've managed to setup static NAT rules for my HTTP/HTTPS/SMTP/etc. services which are running on my LAN. I don't know whether it's worth mentioning that I've opted to use NVI NAT (ip nat enable as opposed to the traditional ip nat outside/ip nat inside) setup. My reason for this is that NVI allows NAT loopback from my LAN to the WAN IP and back in to the necessary server on the LAN. I run an Asterisk 1.8 PBX on my LAN, which connects to a SIP provider on the internet. Both inbound and outbound calls through the old setup (WAG320N providing routing/NAT) worked fine. However, since moving to the Cisco 881, inbound calls drop after around 10 seconds, whereas outbound calls work fine. The following message is logged on my Asterisk PBX: [Dec 9 15:27:45] WARNING[27734]: chan_sip.c:3641 retrans_pkt: Retransmission timeout reached on transmission [email protected] for seqno 1 (Critical Response) -- See https://wiki.asterisk.org/wiki/display/AST/SIP+Retransmissions Packet timed out after 6528ms with no response [Dec 9 15:27:45] WARNING[27734]: chan_sip.c:3670 retrans_pkt: Hanging up call [email protected] - no reply to our critical packet (see https://wiki.asterisk.org/wiki/display/AST/SIP+Retransmissions). (I know that this is quite a common issue - I've spend the best part of 2 days solid on this, trawling Google.) I've done as I am told and checked https://wiki.asterisk.org/wiki/display/AST/SIP+Retransmissions. Referring to the section "Other SIP requests" in the page linked above, I believe that the hangup to be caused by the ACK from my SIP provider not being passed back through NAT to Asterisk on my PBX. I tried to ascertain this by dumping the packets on my WAN interface on the 881. I managed to obtain a PCAP dump of packets in/out of my WAN interface. Here's an example of an ACK being reveived by the router from my provider: 689 21.219999 193.x.x.x 188.x.x.x SIP 502 Request: ACK sip:[email protected] | However a SIP trace on the Asterisk server show's that there are no ACK's received in response to the 200 OK from my PBX: http://pastebin.com/wwHpLPPz In the past, I have been strongly advised to disable any sort of SIP ALGs on routers and/or firewalls and the many posts regarding this issue on the internet seem to support this. However, I believe on Cisco IOS, the config command to disable SIP ALG is no ip nat service sip udp port 5060 however, this doesn't appear to help the situation. To confirm that config setting is set: Router1#show running-config | include sip no ip nat service sip udp port 5060 Another interesting twist: for a short period of time, I tried another provider. Luckily, my trial account with them is still available, so I reverted my Asterisk config back to the revision before I integrated with my current provider. I then dialled in to the DDI associated with the trial trunk and the call didn't get hung up and I didn't get the error above! To me, this points at the provider, however I know, like all providers do, will say "There's no issues with our SIP proxies - it's your firewall." I'm tempted to agree with this, as this issue was not apparent with the old WAG320N router when it was doing the NAT'ing. I'm sure you'll want to see my running-config too: ! ! Last configuration change at 15:55:07 UTC Sun Dec 9 2012 by xxx version 15.2 no service pad service tcp-keepalives-in service tcp-keepalives-out service timestamps debug datetime msec localtime show-timezone service timestamps log datetime msec localtime show-timezone no service password-encryption service sequence-numbers ! hostname Router1 ! boot-start-marker boot-end-marker ! ! security authentication failure rate 10 log security passwords min-length 6 logging buffered 4096 logging console critical enable secret 4 xxx ! aaa new-model ! ! aaa authentication login local_auth local ! ! ! ! ! aaa session-id common ! memory-size iomem 10 ! crypto pki trustpoint TP-self-signed-xxx enrollment selfsigned subject-name cn=IOS-Self-Signed-Certificate-xxx revocation-check none rsakeypair TP-self-signed-xxx ! ! crypto pki certificate chain TP-self-signed-xxx certificate self-signed 01 quit no ip source-route no ip gratuitous-arps ip auth-proxy max-login-attempts 5 ip admission max-login-attempts 5 ! ! ! ! ! no ip bootp server ip domain name dmz.merlin.local ip domain list dmz.merlin.local ip domain list merlin.local ip name-server x.x.x.x ip inspect audit-trail ip inspect udp idle-time 1800 ip inspect dns-timeout 7 ip inspect tcp idle-time 14400 ip inspect name autosec_inspect ftp timeout 3600 ip inspect name autosec_inspect http timeout 3600 ip inspect name autosec_inspect rcmd timeout 3600 ip inspect name autosec_inspect realaudio timeout 3600 ip inspect name autosec_inspect smtp timeout 3600 ip inspect name autosec_inspect tftp timeout 30 ip inspect name autosec_inspect udp timeout 15 ip inspect name autosec_inspect tcp timeout 3600 ip cef login block-for 3 attempts 3 within 3 no ipv6 cef ! ! multilink bundle-name authenticated license udi pid CISCO881-SEC-K9 sn ! ! username xxx privilege 15 secret 4 xxx username xxx secret 4 xxx ! ! ! ! ! ip ssh time-out 60 ! ! ! ! ! ! ! ! ! interface FastEthernet0 no ip address ! interface FastEthernet1 no ip address ! interface FastEthernet2 no ip address ! interface FastEthernet3 switchport access vlan 2 no ip address ! interface FastEthernet4 ip address dhcp no ip redirects no ip unreachables no ip proxy-arp ip nat enable duplex auto speed auto ! interface Vlan1 ip address 192.168.1.1 255.255.255.0 no ip redirects no ip unreachables no ip proxy-arp ip nat enable ! interface Vlan2 ip address 192.168.0.2 255.255.255.0 ! ip forward-protocol nd ip http server ip http access-class 1 ip http authentication local ip http secure-server ip http timeout-policy idle 60 life 86400 requests 10000 ! ! no ip nat service sip udp port 5060 ip nat source list 1 interface FastEthernet4 overload ip nat source static tcp x.x.x.x 80 interface FastEthernet4 80 ip nat source static tcp x.x.x.x 443 interface FastEthernet4 443 ip nat source static tcp x.x.x.x 25 interface FastEthernet4 25 ip nat source static tcp x.x.x.x 587 interface FastEthernet4 587 ip nat source static tcp x.x.x.x 143 interface FastEthernet4 143 ip nat source static tcp x.x.x.x 993 interface FastEthernet4 993 ip nat source static tcp x.x.x.x 1723 interface FastEthernet4 1723 ! ! logging trap debugging logging facility local2 access-list 1 permit 192.168.1.0 0.0.0.255 access-list 1 permit 192.168.0.0 0.0.0.255 no cdp run ! ! ! ! control-plane ! ! banner motd Authorized Access only ! line con 0 login authentication local_auth length 0 transport output all line aux 0 exec-timeout 15 0 login authentication local_auth transport output all line vty 0 1 access-class 1 in logging synchronous login authentication local_auth length 0 transport preferred none transport input telnet transport output all line vty 2 4 access-class 1 in login authentication local_auth length 0 transport input ssh transport output all ! ! end ...and, if it's of any use, here's my Asterisk SIP config: [general] context=default ; Default context for calls allowoverlap=no ; Disable overlap dialing support. (Default is yes) udpbindaddr=0.0.0.0 ; IP address to bind UDP listen socket to (0.0.0.0 binds to all) ; Optionally add a port number, 192.168.1.1:5062 (default is port 5060) tcpenable=no ; Enable server for incoming TCP connections (default is no) tcpbindaddr=0.0.0.0 ; IP address for TCP server to bind to (0.0.0.0 binds to all interfaces) ; Optionally add a port number, 192.168.1.1:5062 (default is port 5060) srvlookup=yes ; Enable DNS SRV lookups on outbound calls ; Note: Asterisk only uses the first host ; in SRV records ; Disabling DNS SRV lookups disables the ; ability to place SIP calls based on domain ; names to some other SIP users on the Internet ; Specifying a port in a SIP peer definition or ; when dialing outbound calls will supress SRV ; lookups for that peer or call. directmedia=no ; Don't allow direct RTP media between extensions (doesn't work through NAT) externhost=<MY DYNDNS HOSTNAME> ; Our external hostname to resolve to IP and be used in NAT'ed packets localnet=192.168.1.0/24 ; Define our local network so we know which packets need NAT'ing qualify=yes ; Qualify peers by default dtmfmode=rfc2833 ; Set the default DTMF mode disallow=all ; Disallow all codecs by default allow=ulaw ; Allow G.711 u-law allow=alaw ; Allow G.711 a-law ; ---------------------- ; SIP Trunk Registration ; ---------------------- ; Orbtalk register => <MY SIP PROVIDER USER NAME>:[email protected]/<MY DDI> ; Main Orbtalk number ; ---------- ; Trunks ; ---------- [orbtalk] ; Main Orbtalk trunk type=peer insecure=invite host=sipgw3.orbtalk.co.uk nat=yes username=<MY SIP PROVIDER USER NAME> defaultuser=<MY SIP PROVIDER USER NAME> fromuser=<MY SIP PROVIDER USER NAME> secret=xxx context=inbound I really don't know where to go with this. If anyone can help me find out why these calls are being dropped off, I'd be grateful if you could chime in! Please let me know if any further info is required.

  Read the article

• How to route to a secondary interface on the same physical ethernet?

  - by sjose3612611

  INTERNET<->(wan)BRIDGED_DEVICE(lan)<->ETH_ROUTER<->LAN Problem: Need to access web server on BRIDGED_DEVICE's LAN from INTERNET via ROUTER (BRIDGED_DEVICE's web server cannot be accessed form INTERNET since it has no Public management IP). Cannot configure bridged device. It has a static IP on its LAN to which its web server binds. Attempt: Create a secondary/alias WAN Interface on ETH_ROUTER (e.g Primary: eth0.1 (for internet access) and Secondary: eth0.2 (for accessing web server on BRIDGED_DEVICE), (No VLANs). eth0.1 has a public IP; eth0.2 has a static private IP in the BRIDGED_DEVICE's subnet (e.g 10.0.X.Y). Iptables on ETH_ROUTER: Added a port forward (DNAT) from eth0.1 to eth0.2: iptables -t nat -I PREROUTING -i eth0.1 -p tcp --dport 80 -j DNAT --to-destination 10.0.X.Y iptables -t nat -I POSTROUTING -o eth0.2 -s 10.0.X.0/24 -j MASQUERADE Stateful firewall w/ overall drop policy on FORWARD chain, hence: iptables -I FORWARD -i eth0.1 -d 10.0.X.Y -p tcp --dport 80 -j ACCEPT Can ping from ETH_ROUTER to BRIDGED_DEVICE but unable to reach the web server from Internet. I see packet cont increasing for the DNAT rule but not sure where it disappears in the ETH_ROUTER after that. ETH_ROUTER is the only device that can be configured to achieve this. If familiar with this scenario, please suggest what I may be missing or doing wrong here or suggest techniques to debug?

  Read the article

• Is it possible to command a common router without using the web interface?

  - by MDeSchaepmeester

  Some background The internet arrangement in my student home is really weird. There is one ethernet outlet and several wifi hotspots. Either way requires a login through a web site to get internet access. This is annoying as each device needs to login seperately and with a PS3 for example, it is impossible to get connected at all since the web login procedure doesn't work. Therefore I have installed a D-Link DIR-635 router which is connected to the ethernet outlet. It has DHCP enabled so it uses NAT, but whatever it is connected to also uses NAT and I've read this should not work. A fellow student tried it with an Apple Airport but that keeps giving errors related to NAT after NAT. Anyway my setup does work so bonus points if you can clarify this. I need to login to the web site I mentioned earlier with any device, after which all devices in my LAN have connectivity. This is great. Except... In short From time to time, I lose internet connectivity and my D-Link DIR-635 router needs to do a DHCP renew. I can do this via the web interface but my life would be easier if I could just run a cmd file which tells my router to do this without all the hassle. This would setup a connection to my router and execute the proper command. I have tried googling but couldn't find much helpful stuff.

  Read the article

• Design Question - how do you break the dependency between classes using an interface?

  - by Seth Spearman

  Hello, I apologize in advance but this will be a long question. I'm stuck. I am trying to learn unit testing, C#, and design patterns - all at once. (Maybe that's my problem.) As such I am reading the Art of Unit Testing (Osherove), and Clean Code (Martin), and Head First Design Patterns (O'Reilly). I am just now beginning to understand delegates and events (which you would see if you were to troll my SO questions of recent). I still don't quite get lambdas. To contextualize all of this I have given myself a learning project I am calling goAlarms. I have an Alarm class with members you'd expect (NextAlarmTime, Name, AlarmGroup, Event Trigger etc.) I wanted the "Timer" of the alarm to be extensible so I created an IAlarmScheduler interface as follows... public interface AlarmScheduler { Dictionary<string,Alarm> AlarmList { get; } void Startup(); void Shutdown(); void AddTrigger(string triggerName, string groupName, Alarm alarm); void RemoveTrigger(string triggerName); void PauseTrigger(string triggerName); void ResumeTrigger(string triggerName); void PauseTriggerGroup(string groupName); void ResumeTriggerGroup(string groupName); void SetSnoozeTrigger(string triggerName, int duration); void SetNextOccurrence (string triggerName, DateTime nextOccurrence); } This IAlarmScheduler interface define a component that will RAISE an alarm (Trigger) which will bubble up to my Alarm class and raise the Trigger Event of the alarm itself. It is essentially the "Timer" component. I have found that the Quartz.net component is perfectly suited for this so I have created a QuartzAlarmScheduler class which implements IAlarmScheduler. All that is fine. My problem is that the Alarm class is abstract and I want to create a lot of different KINDS of alarm. For example, I already have a Heartbeat alarm (triggered every (int) interval of minutes), AppointmentAlarm (triggered on set date and time), Daily Alarm (triggered every day at X) and perhaps others. And Quartz.NET is perfectly suited to handle this. My problem is a design problem. I want to be able to instantiate an alarm of any kind without my Alarm class (or any derived classes) knowing anything about Quartz. The problem is that Quartz has awesome factories that return just the right setup for the Triggers that will be needed by my Alarm classes. So, for example, I can get a Quartz trigger by using TriggerUtils.MakeMinutelyTrigger to create a trigger for the heartbeat alarm described above. Or TriggerUtils.MakeDailyTrigger for the daily alarm. I guess I could sum it up this way. Indirectly or directly I want my alarm classes to be able to consume the TriggerUtils.Make* classes without knowing anything about them. I know that is a contradiction, but that is why I am asking the question. I thought about putting a delegate field into the alarm which would be assigned one of these Make method but by doing that I am creating a hard dependency between alarm and Quartz which I want to avoid for both unit testing purposes and design purposes. I thought of using a switch for the type in QuartzAlarmScheduler per here but I know it is bad design and I am trying to learn good design. If I may editorialize a bit. I've decided that coding (predefined) classes is easy. Design is HARD...in fact, really hard and I am really fighting feeling stupid right now. I guess I want to know if you really smart people took a while to really understand and master this stuff or should I feel stupid (as I do) because I haven't grasped it better in the couple of weeks/months I have been studying. You guys are awesome and thanks in advance for your answers. Seth

  Read the article

• What are the names of network interfaces on the Motorola CLIQ?

  - by RS

  The network interfaces on Android interfaces are listed as directories in the file system in /sys/class/net/. For most Android devices the network interface for gprs traffic is called rmnet0 and for Wi-Fi it's usually eth0 or tiwlan0. I suspect that the cell interface for the Motorola CLIQ is rmnet0, but I would like to have this confirmed + know the name of the Wi-Fi interface. Also it would be good to know the device id for this model. This is the value available as android.os.Build.DEVICE in the Java SDK. (E.g. T-Mobile G1 uses dream, Samsung Galaxy uses GT-I7500, and Motorolda Droid uses sholes.)

  Read the article

• What are the names of network interfaces on the Motorola CLIQ XT?

  - by RS

  The network interfaces on Android interfaces are listed as directories in the file system in /sys/class/net/. For most Android devices the network interface for gprs traffic is called rmnet0 and for Wi-Fi it's usually eth0 or tiwlan0. I suspect that the cell interface for the Motorola CLIQ XT is rmnet0, but I would like to have this confirmed + know the name of the Wi-Fi interface. Also it would be good to know the device id for this model. This is the value available as android.os.Build.DEVICE in the Java SDK. (E.g. T-Mobile G1 uses dream, Samsung Galaxy uses GT-I7500, and Motorolda Droid uses sholes.)

  Read the article

• How do I get the IPv4 subnetmask on interface with both v4 and v6 address?

  - by Per Fagrell

  I have an InterfaceAddress that returns an ipv4 address (4 octets). However the network prefix length seems to be for the ipv6 address associated with the interface (it's returning as 128). How do I find the correct network prefix length? Enumeration<NetworkInterface> NetworkInterface.getNetworkInterfaces() for (; interfaces.hasMoreElements();) { final List<InterfaceAddress>interfaceAddresses = interfaces.nextElement().getInterfaceAddresses(); for (final InterfaceAddress address : interfaceAddresses) { assert(address.getAddress().getAddress().length == 4); // [sic] assert(address.getNetworkPrefixLength() < 32); // <- Fails. Actually equals 128 } }

  Read the article

• How do I locate the app generating this network traffic?

  - by Christopher Bartels

  I don't know what this process is doing on my computer. I run Windows 7 Professional w/ all its updates running current non-free antivirus. I only see it in Resource Monitor, where you can see the Network Service process connected to bitum.nnov.ru. When my PC's network traffic generating apps are idle, this process is using the most of all the idle processes using the network. Screenshot hosted here: http://sss.proinbox.com/bitum-nnov-ru.jpg Does anyone recognize this? The page source mentions a control port & a stream port: Page Source for http://bitum.nnov.ru : <!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.01 Transitional//EN"> <html> <head> <title>DVR WebViewer</title> <meta http-equiv="Content-Type" content="text/html; charset=euc-kr"> </head> <body topmargin="0" leftmargin="0"> <OBJECT classid="clsid:EE479A40-C128-40DD-93DA-000556AF9607" codebase="CtrWeb.cab#version=1,0,2,2" width=875 height=585 align=center hspace=0 vspace=0 > <param name="CmdPort" value="5920"> <param name="StreamPort" value="5921"> </body> </html> When I google this page's title, I see a number of other domains that host the same page. Whois: domain: NNOV.RU nserver: ns.kis.ru. nserver: ns.nnov.ru. 78.25.80.210 nserver: ns1.kis.ru. nserver: ns2.kis.ru. state: REGISTERED, DELEGATED, VERIFIED org: "Agentstvo Delovoj Svjazi", Ltd registrar: RU-CENTER-REG-RIPN admin-contact: https://www.nic.ru/whois created: 1996.10.23 paid-till: 2012.11.01 free-date: 2012.12.02 source: TCI Last updated on 2012.06.16 04:20:46 MSK

  Read the article

• Frequent Disconnects ubuntu desktop 12.10 x64 intel 82579V e1000e

  - by user112055

  I'm having frequent disconnects with my new install of Ubuntu 12.10. I tried updating the kernel driver to the latest intel release to no avail. My expertise is spent. It happens anywhere between 1 min and 10 min. Any ideas? syslog: Dec 1 13:51:39 andromeda kernel: [ 972.188809] audit_printk_skb: 6 callbacks suppressed Dec 1 13:51:39 andromeda kernel: [ 972.188813] type=1701 audit(1354398699.418:199): auid=4294967295 uid=1000 gid=1000 ses=4294967295 pid=6039 comm="chrome" reason="seccomp" sig=0 syscall=4 compat=0 ip=0x7f26777d9205 code=0x50000 Dec 1 13:51:39 andromeda kernel: [ 972.188817] type=1701 audit(1354398699.418:200): auid=4294967295 uid=1000 gid=1000 ses=4294967295 pid=6039 comm="chrome" reason="seccomp" sig=0 syscall=4 compat=0 ip=0x7f26777d9205 code=0x50000 Dec 1 13:51:39 andromeda kernel: [ 972.188820] type=1701 audit(1354398699.418:201): auid=4294967295 uid=1000 gid=1000 ses=4294967295 pid=6039 comm="chrome" reason="seccomp" sig=0 syscall=4 compat=0 ip=0x7f26777d9205 code=0x50000 Dec 1 13:51:39 andromeda kernel: [ 972.188823] type=1701 audit(1354398699.418:202): auid=4294967295 uid=1000 gid=1000 ses=4294967295 pid=6039 comm="chrome" reason="seccomp" sig=0 syscall=4 compat=0 ip=0x7f26777d9205 code=0x50000 Dec 1 13:51:39 andromeda kernel: [ 972.188825] type=1701 audit(1354398699.418:203): auid=4294967295 uid=1000 gid=1000 ses=4294967295 pid=6039 comm="chrome" reason="seccomp" sig=0 syscall=4 compat=0 ip=0x7f26777d9205 code=0x50000 Dec 1 13:51:39 andromeda kernel: [ 972.331419] type=1701 audit(1354398699.558:204): auid=4294967295 uid=1000 gid=1000 ses=4294967295 pid=6039 comm="chrome" reason="seccomp" sig=0 syscall=2 compat=0 ip=0x7f26777d96b0 code=0x50000 Dec 1 13:53:12 andromeda NetworkManager[1115]: <info> (eth0): carrier now OFF (device state 100, deferring action for 4 seconds) Dec 1 13:53:12 andromeda kernel: [ 1064.894387] e1000e: e1000e: eth0 NIC Link is Down Dec 1 13:53:16 andromeda NetworkManager[1115]: <info> (eth0): device state change: activated -> unavailable (reason 'carrier-changed') [100 20 40] Dec 1 13:53:16 andromeda NetworkManager[1115]: <info> (eth0): deactivating device (reason 'carrier-changed') [40] Dec 1 13:53:16 andromeda NetworkManager[1115]: <info> (eth0): canceled DHCP transaction, DHCP client pid 5946 Dec 1 13:53:16 andromeda avahi-daemon[890]: Withdrawing address record for fe80::ea40:f2ff:fee2:4d86 on eth0. Dec 1 13:53:16 andromeda avahi-daemon[890]: Leaving mDNS multicast group on interface eth0.IPv6 with address fe80::ea40:f2ff:fee2:4d86. Dec 1 13:53:16 andromeda avahi-daemon[890]: Interface eth0.IPv6 no longer relevant for mDNS. Dec 1 13:53:16 andromeda kernel: [ 1069.025288] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready Dec 1 13:53:16 andromeda avahi-daemon[890]: Withdrawing address record for 192.168.11.17 on eth0. Dec 1 13:53:16 andromeda avahi-daemon[890]: Leaving mDNS multicast group on interface eth0.IPv4 with address 192.168.11.17. Dec 1 13:53:16 andromeda avahi-daemon[890]: Interface eth0.IPv4 no longer relevant for mDNS. Dec 1 13:53:16 andromeda NetworkManager[1115]: <warn> DNS: plugin dnsmasq update failed Dec 1 13:53:16 andromeda NetworkManager[1115]: <info> ((null)): removing resolv.conf from /sbin/resolvconf Dec 1 13:53:16 andromeda dnsmasq[1907]: setting upstream servers from DBus Dec 1 13:53:16 andromeda dbus[800]: [system] Activating service name='org.freedesktop.nm_dispatcher' (using servicehelper) Dec 1 13:53:16 andromeda dbus[800]: [system] Successfully activated service 'org.freedesktop.nm_dispatcher' Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> (eth0): carrier now ON (device state 20) Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> (eth0): device state change: unavailable -> disconnected (reason 'carrier-changed') [20 30 40] Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> Auto-activating connection '82579V'. Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> Activation (eth0) starting connection '82579V' Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> (eth0): device state change: disconnected -> prepare (reason 'none') [30 40 0] Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> Activation (eth0) Stage 1 of 5 (Device Prepare) scheduled... Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> Activation (eth0) Stage 1 of 5 (Device Prepare) started... Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> Activation (eth0) Stage 2 of 5 (Device Configure) scheduled... Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> Activation (eth0) Stage 1 of 5 (Device Prepare) complete. Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> Activation (eth0) Stage 2 of 5 (Device Configure) starting... Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> (eth0): device state change: prepare -> config (reason 'none') [40 50 0] Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> Activation (eth0) Stage 2 of 5 (Device Configure) successful. Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> Activation (eth0) Stage 3 of 5 (IP Configure Start) scheduled. Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> Activation (eth0) Stage 2 of 5 (Device Configure) complete. Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> Activation (eth0) Stage 3 of 5 (IP Configure Start) started... Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> (eth0): device state change: config -> ip-config (reason 'none') [50 70 0] Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> Activation (eth0) Beginning DHCPv4 transaction (timeout in 45 seconds) Dec 1 13:53:32 andromeda kernel: [ 1084.938042] e1000e: e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: Rx/Tx Dec 1 13:53:32 andromeda kernel: [ 1084.938049] e1000e 0000:00:19.0: eth0: 10/100 speed: disabling TSO Dec 1 13:53:32 andromeda kernel: [ 1084.938815] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> dhclient started with pid 6080 Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> Activation (eth0) Stage 3 of 5 (IP Configure Start) complete. Dec 1 13:53:32 andromeda dhclient: Internet Systems Consortium DHCP Client 4.2.4 Dec 1 13:53:32 andromeda dhclient: Copyright 2004-2012 Internet Systems Consortium. Dec 1 13:53:32 andromeda dhclient: All rights reserved. Dec 1 13:53:32 andromeda dhclient: For info, please visit https://www.isc.org/software/dhcp/ Dec 1 13:53:32 andromeda dhclient: Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> (eth0): DHCPv4 state changed nbi -> preinit Dec 1 13:53:32 andromeda dhclient: Listening on LPF/eth0/e8:40:f2:e2:4d:86 Dec 1 13:53:32 andromeda dhclient: Sending on LPF/eth0/e8:40:f2:e2:4d:86 Dec 1 13:53:32 andromeda dhclient: Sending on Socket/fallback Dec 1 13:53:32 andromeda dhclient: DHCPREQUEST of 192.168.11.17 on eth0 to 255.255.255.255 port 67 Dec 1 13:53:32 andromeda dhclient: DHCPACK of 192.168.11.17 from 192.168.11.1 Dec 1 13:53:32 andromeda dhclient: bound to 192.168.11.17 -- renewal in 33576 seconds. Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> (eth0): DHCPv4 state changed preinit -> reboot Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> address 192.168.11.17 Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> prefix 24 (255.255.255.0) Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> gateway 192.168.11.1 Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> hostname 'andromeda' Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> nameserver '192.168.11.1' Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> domain name 'hsd1.ca.comcast.net' Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> Activation (eth0) Stage 5 of 5 (IPv4 Configure Commit) scheduled... Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> Activation (eth0) Stage 5 of 5 (IPv4 Commit) started... Dec 1 13:53:32 andromeda avahi-daemon[890]: Joining mDNS multicast group on interface eth0.IPv4 with address 192.168.11.17. Dec 1 13:53:32 andromeda avahi-daemon[890]: New relevant interface eth0.IPv4 for mDNS. Dec 1 13:53:32 andromeda avahi-daemon[890]: Registering new address record for 192.168.11.17 on eth0.IPv4. Dec 1 13:53:33 andromeda NetworkManager[1115]: <info> (eth0): device state change: ip-config -> activated (reason 'none') [70 100 0] Dec 1 13:53:33 andromeda NetworkManager[1115]: <info> ((null)): writing resolv.conf to /sbin/resolvconf Dec 1 13:53:33 andromeda dnsmasq[1907]: setting upstream servers from DBus Dec 1 13:53:33 andromeda dnsmasq[1907]: using nameserver 192.168.11.1#53 Dec 1 13:53:33 andromeda NetworkManager[1115]: <info> Policy set '82579V' (eth0) as default for IPv4 routing and DNS. Dec 1 13:53:33 andromeda NetworkManager[1115]: <info> Activation (eth0) successful, device activated. Dec 1 13:53:33 andromeda NetworkManager[1115]: <info> Activation (eth0) Stage 5 of 5 (IPv4 Commit) complete. Dec 1 13:53:33 andromeda dbus[800]: [system] Activating service name='org.freedesktop.nm_dispatcher' (using servicehelper) Dec 1 13:53:33 andromeda dbus[800]: [system] Successfully activated service 'org.freedesktop.nm_dispatcher' Dec 1 13:53:33 andromeda avahi-daemon[890]: Joining mDNS multicast group on interface eth0.IPv6 with address fe80::ea40:f2ff:fee2:4d86. Dec 1 13:53:33 andromeda avahi-daemon[890]: New relevant interface eth0.IPv6 for mDNS. Dec 1 13:53:33 andromeda avahi-daemon[890]: Registering new address record for fe80::ea40:f2ff:fee2:4d86 on eth0.*. Dec 1 13:53:41 andromeda ntpdate[6154]: adjust time server 91.189.94.4 offset 0.000928 sec Dec 1 13:53:50 andromeda NetworkManager[1115]: <info> (eth0): carrier now OFF (device state 100, deferring action for 4 seconds) Dec 1 13:53:50 andromeda kernel: [ 1102.980003] e1000e: e1000e: eth0 NIC Link is Down Dec 1 13:53:54 andromeda NetworkManager[1115]: <info> (eth0): device state change: activated -> unavailable (reason 'carrier-changed') [100 20 40] Dec 1 13:53:54 andromeda NetworkManager[1115]: <info> (eth0): deactivating device (reason 'carrier-changed') [40] Dec 1 13:53:54 andromeda NetworkManager[1115]: <info> (eth0): canceled DHCP transaction, DHCP client pid 6080 Dec 1 13:53:54 andromeda avahi-daemon[890]: Withdrawing address record for fe80::ea40:f2ff:fee2:4d86 on eth0. Dec 1 13:53:54 andromeda avahi-daemon[890]: Leaving mDNS multicast group on interface eth0.IPv6 with address fe80::ea40:f2ff:fee2:4d86. Dec 1 13:53:54 andromeda avahi-daemon[890]: Interface eth0.IPv6 no longer relevant for mDNS. Dec 1 13:53:54 andromeda avahi-daemon[890]: Withdrawing address record for 192.168.11.17 on eth0. Dec 1 13:53:54 andromeda avahi-daemon[890]: Leaving mDNS multicast group on interface eth0.IPv4 with address 192.168.11.17. Dec 1 13:53:54 andromeda kernel: [ 1107.025959] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready Dec 1 13:53:54 andromeda NetworkManager[1115]: <warn> DNS: plugin dnsmasq update failed Dec 1 13:53:54 andromeda NetworkManager[1115]: <info> ((null)): removing resolv.conf from /sbin/resolvconf Dec 1 13:53:54 andromeda avahi-daemon[890]: Interface eth0.IPv4 no longer relevant for mDNS. Dec 1 13:53:54 andromeda dnsmasq[1907]: setting upstream servers from DBus Dec 1 13:53:54 andromeda dbus[800]: [system] Activating service name='org.freedesktop.nm_dispatcher' (using servicehelper) Dec 1 13:53:54 andromeda dbus[800]: [system] Successfully activated service 'org.freedesktop.nm_dispatcher' Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> (eth0): carrier now ON (device state 20) Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> (eth0): device state change: unavailable -> disconnected (reason 'carrier-changed') [20 30 40] Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> Auto-activating connection '82579V'. Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> Activation (eth0) starting connection '82579V' Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> (eth0): device state change: disconnected -> prepare (reason 'none') [30 40 0] Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> Activation (eth0) Stage 1 of 5 (Device Prepare) scheduled... Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> Activation (eth0) Stage 1 of 5 (Device Prepare) started... Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> Activation (eth0) Stage 2 of 5 (Device Configure) scheduled... Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> Activation (eth0) Stage 1 of 5 (Device Prepare) complete. Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> Activation (eth0) Stage 2 of 5 (Device Configure) starting... Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> (eth0): device state change: prepare -> config (reason 'none') [40 50 0] Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> Activation (eth0) Stage 2 of 5 (Device Configure) successful. Dec 1 13:54:10 andromeda kernel: [ 1123.167668] e1000e: e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: Rx/Tx Dec 1 13:54:10 andromeda kernel: [ 1123.167675] e1000e 0000:00:19.0: eth0: 10/100 speed: disabling TSO Dec 1 13:54:10 andromeda kernel: [ 1123.168430] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> Activation (eth0) Stage 3 of 5 (IP Configure Start) scheduled. Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> Activation (eth0) Stage 2 of 5 (Device Configure) complete. Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> Activation (eth0) Stage 3 of 5 (IP Configure Start) started... Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> (eth0): device state change: config -> ip-config (reason 'none') [50 70 0] Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> Activation (eth0) Beginning DHCPv4 transaction (timeout in 45 seconds) Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> dhclient started with pid 6212 Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> Activation (eth0) Stage 3 of 5 (IP Configure Start) complete. Dec 1 13:54:10 andromeda dhclient: Internet Systems Consortium DHCP Client 4.2.4 Dec 1 13:54:10 andromeda dhclient: Copyright 2004-2012 Internet Systems Consortium. Dec 1 13:54:10 andromeda dhclient: All rights reserved. Dec 1 13:54:10 andromeda dhclient: For info, please visit https://www.isc.org/software/dhcp/ Dec 1 13:54:10 andromeda dhclient: Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> (eth0): DHCPv4 state changed nbi -> preinit Dec 1 13:54:10 andromeda dhclient: Listening on LPF/eth0/e8:40:f2:e2:4d:86 Dec 1 13:54:10 andromeda dhclient: Sending on LPF/eth0/e8:40:f2:e2:4d:86 Dec 1 13:54:10 andromeda dhclient: Sending on Socket/fallback Dec 1 13:54:10 andromeda dhclient: DHCPREQUEST of 192.168.11.17 on eth0 to 255.255.255.255 port 67 Dec 1 13:54:10 andromeda dhclient: DHCPACK of 192.168.11.17 from 192.168.11.1 Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> (eth0): DHCPv4 state changed preinit -> reboot Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> address 192.168.11.17 Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> prefix 24 (255.255.255.0) Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> gateway 192.168.11.1 Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> hostname 'andromeda' Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> nameserver '192.168.11.1' Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> domain name 'hsd1.ca.comcast.net' Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> Activation (eth0) Stage 5 of 5 (IPv4 Configure Commit) scheduled... Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> Activation (eth0) Stage 5 of 5 (IPv4 Commit) started... Dec 1 13:54:10 andromeda avahi-daemon[890]: Joining mDNS multicast group on interface eth0.IPv4 with address 192.168.11.17. Dec 1 13:54:10 andromeda dhclient: bound to 192.168.11.17 -- renewal in 35416 seconds. Dec 1 13:54:10 andromeda avahi-daemon[890]: New relevant interface eth0.IPv4 for mDNS. Dec 1 13:54:10 andromeda avahi-daemon[890]: Registering new address record for 192.168.11.17 on eth0.IPv4. Dec 1 13:54:11 andromeda NetworkManager[1115]: <info> (eth0): device state change: ip-config -> activated (reason 'none') [70 100 0] Dec 1 13:54:11 andromeda NetworkManager[1115]: <info> ((null)): writing resolv.conf to /sbin/resolvconf Dec 1 13:54:11 andromeda dnsmasq[1907]: setting upstream servers from DBus Dec 1 13:54:11 andromeda dnsmasq[1907]: using nameserver 192.168.11.1#53 Dec 1 13:54:11 andromeda NetworkManager[1115]: <info> Policy set '82579V' (eth0) as default for IPv4 routing and DNS. Dec 1 13:54:11 andromeda NetworkManager[1115]: <info> Activation (eth0) successful, device activated. Dec 1 13:54:11 andromeda NetworkManager[1115]: <info> Activation (eth0) Stage 5 of 5 (IPv4 Commit) complete. Dec 1 13:54:11 andromeda dbus[800]: [system] Activating service name='org.freedesktop.nm_dispatcher' (using servicehelper) Dec 1 13:54:11 andromeda dbus[800]: [system] Successfully activated service 'org.freedesktop.nm_dispatcher' Dec 1 13:54:12 andromeda avahi-daemon[890]: Joining mDNS multicast group on interface eth0.IPv6 with address fe80::ea40:f2ff:fee2:4d86. Dec 1 13:54:12 andromeda avahi-daemon[890]: New relevant interface eth0.IPv6 for mDNS. Dec 1 13:54:12 andromeda avahi-daemon[890]: Registering new address record for fe80::ea40:f2ff:fee2:4d86 on eth0.*. Dec 1 13:54:19 andromeda ntpdate[6286]: adjust time server 91.189.94.4 offset 0.001142 sec $ lspci -v 00:19.0 Ethernet controller: Intel Corporation 82579V Gigabit Network Connection (rev 04) Subsystem: Intel Corporation Device 2031 Flags: bus master, fast devsel, latency 0, IRQ 45 Memory at f7f00000 (32-bit, non-prefetchable) [size=128K] Memory at f7f39000 (32-bit, non-prefetchable) [size=4K] I/O ports at f040 [size=32] Capabilities: [c8] Power Management version 2 Capabilities: [d0] MSI: Enable+ Count=1/1 Maskable- 64bit+ Capabilities: [e0] PCI Advanced Features Kernel driver in use: e1000e Kernel modules: e1000e $ modinfo e1000e filename: /lib/modules/3.5.0-19-generic/kernel/drivers/net/e1000e/e1000e.ko version: 2.1.4-NAPI license: GPL description: Intel(R) PRO/1000 Network Driver author: Intel Corporation, <[email protected]> srcversion: 0809529BE0BBC44883956AF alias: pci:v00008086d0000153Bsv*sd*bc*sc*i* alias: pci:v00008086d0000153Asv*sd*bc*sc*i* alias: pci:v00008086d00001503sv*sd*bc*sc*i* alias: pci:v00008086d00001502sv*sd*bc*sc*i* alias: pci:v00008086d000010F0sv*sd*bc*sc*i* alias: pci:v00008086d000010EFsv*sd*bc*sc*i* alias: pci:v00008086d000010EBsv*sd*bc*sc*i* alias: pci:v00008086d000010EAsv*sd*bc*sc*i* alias: pci:v00008086d00001525sv*sd*bc*sc*i* alias: pci:v00008086d000010DFsv*sd*bc*sc*i* alias: pci:v00008086d000010DEsv*sd*bc*sc*i* alias: pci:v00008086d000010CEsv*sd*bc*sc*i* alias: pci:v00008086d000010CDsv*sd*bc*sc*i* alias: pci:v00008086d000010CCsv*sd*bc*sc*i* alias: pci:v00008086d000010CBsv*sd*bc*sc*i* alias: pci:v00008086d000010F5sv*sd*bc*sc*i* alias: pci:v00008086d000010BFsv*sd*bc*sc*i* alias: pci:v00008086d000010E5sv*sd*bc*sc*i* alias: pci:v00008086d0000294Csv*sd*bc*sc*i* alias: pci:v00008086d000010BDsv*sd*bc*sc*i* alias: pci:v00008086d000010C3sv*sd*bc*sc*i* alias: pci:v00008086d000010C2sv*sd*bc*sc*i* alias: pci:v00008086d000010C0sv*sd*bc*sc*i* alias: pci:v00008086d00001501sv*sd*bc*sc*i* alias: pci:v00008086d00001049sv*sd*bc*sc*i* alias: pci:v00008086d0000104Dsv*sd*bc*sc*i* alias: pci:v00008086d0000104Bsv*sd*bc*sc*i* alias: pci:v00008086d0000104Asv*sd*bc*sc*i* alias: pci:v00008086d000010C4sv*sd*bc*sc*i* alias: pci:v00008086d000010C5sv*sd*bc*sc*i* alias: pci:v00008086d0000104Csv*sd*bc*sc*i* alias: pci:v00008086d000010BBsv*sd*bc*sc*i* alias: pci:v00008086d00001098sv*sd*bc*sc*i* alias: pci:v00008086d000010BAsv*sd*bc*sc*i* alias: pci:v00008086d00001096sv*sd*bc*sc*i* alias: pci:v00008086d0000150Csv*sd*bc*sc*i* alias: pci:v00008086d000010F6sv*sd*bc*sc*i* alias: pci:v00008086d000010D3sv*sd*bc*sc*i* alias: pci:v00008086d0000109Asv*sd*bc*sc*i* alias: pci:v00008086d0000108Csv*sd*bc*sc*i* alias: pci:v00008086d0000108Bsv*sd*bc*sc*i* alias: pci:v00008086d0000107Fsv*sd*bc*sc*i* alias: pci:v00008086d0000107Esv*sd*bc*sc*i* alias: pci:v00008086d0000107Dsv*sd*bc*sc*i* alias: pci:v00008086d000010B9sv*sd*bc*sc*i* alias: pci:v00008086d000010D5sv*sd*bc*sc*i* alias: pci:v00008086d000010DAsv*sd*bc*sc*i* alias: pci:v00008086d000010D9sv*sd*bc*sc*i* alias: pci:v00008086d00001060sv*sd*bc*sc*i* alias: pci:v00008086d000010A5sv*sd*bc*sc*i* alias: pci:v00008086d000010BCsv*sd*bc*sc*i* alias: pci:v00008086d000010A4sv*sd*bc*sc*i* alias: pci:v00008086d0000105Fsv*sd*bc*sc*i* alias: pci:v00008086d0000105Esv*sd*bc*sc*i* depends: vermagic: 3.5.0-19-generic SMP mod_unload modversions parm: copybreak:Maximum size of packet that is copied to a new buffer on receive (uint) parm: TxIntDelay:Transmit Interrupt Delay (array of int) parm: TxAbsIntDelay:Transmit Absolute Interrupt Delay (array of int) parm: RxIntDelay:Receive Interrupt Delay (array of int) parm: RxAbsIntDelay:Receive Absolute Interrupt Delay (array of int) parm: InterruptThrottleRate:Interrupt Throttling Rate (array of int) parm: IntMode:Interrupt Mode (array of int) parm: SmartPowerDownEnable:Enable PHY smart power down (array of int) parm: KumeranLockLoss:Enable Kumeran lock loss workaround (array of int) parm: CrcStripping:Enable CRC Stripping, disable if your BMC needs the CRC (array of int) parm: EEE:Enable/disable on parts that support the feature (array of int) parm: Node:[ROUTING] Node to allocate memory on, default -1 (array of int) parm: debug:Debug level (0=none,...,16=all) (int)

  Read the article

• How do I get more information on a potential network freeloader?

  - by Dov

  I have a home network set up, complete with a relatively good password. I'm in Mac OS X 10.6 (Snow Leopard) and have been noticing, on occasion, a computer showing up in my Finder's Shared section, that is not one of my own (the "pe-xpjalle" box pictured below). He has a tendency to come and go. How can I figure out his MAC address or something, so I can block him? I checked my "Logs and Statistics" in the Airport Utility, and didn't see that computer under DHCP clients. I'd rather not change my password, since I have quite a few devices I'd have to update. Is there any other reason he's show up on my network besides having guessed my password? Update: I fixed the Dropbox URL above (how embarrassing, I'm new to Dropbox. Thanks for the heads up, Doug.) Update 2: I tried clicking on "Connect as..." just for the hell of it, and got the dialog below. Now I have even less an idea what's going on than before. I don't have Parallels of VMware running, just the following: Transmission, NetNewsWire, Mail, Things, Safari, iTunes, Photoshop, Pages, Yojimbo, Preferences, AppleScript Editor, Software Update, Airport Utility, and Terminal. I don't think any of those create a virtual network machine, right? And no VMware machine of mine has ever had a name resembling "pe-xpjalle". Update 3: I just changed my passwords on both my N- and G-only networks, and I'm still seeing this, so I highly doubt that it's someone who's figured out my password (twice now). I'm really stumped.

  Read the article

• Advice needed for a home network setup (hardware & software) to handle many clients and potentially heavy traffic

  - by posdef

  I have recently decided to re-structure the home network of our flatshare here. Here's a quick outline of the situation. I envision to have the following 4 devices connected to the router via cable: Xbox 360 IP phone Printer QNAP server (Web, File and Multimedia) We are three people living here, so on top of that there will be to 5-6 computers/mobile devices connecting as wireless clients. My goal is to be able to transfer files (when needed) between the computer and the Multimedia server, which I can reach via 360 and play on the TV. I also would like to keep a high level of security; right now I have the encryption on WPA2 and MAC filtering. I don't believe the web server will get heavy traffic, though I would like to have it responsive. Likewise, I don't have a habit of downloading via torrent etc, but I greatly appreciate my network being responsive and fast, especially when I am browsing or streaming high quality media. Now my questions are: is this setup feasible? smart? efficient? can this be improved somehow? my current router (D-Link DI624) and the previous one (DI-524) used to have spontaneous drops in network, which I find highly irritating. I don't believe in my router, especially now that it completely crashed when I was test-running the setup by transferring a large media file to server while xbox was playing music from the server, and two computers browsing the net. Do I need to get new hardware, if so, any recommendations for a reliable and fast router?

  Read the article

• Hierarchy flattening of interfaces in WCF

  - by nmarun

  Alright, so say I have my service contract interface as below: 1: [ServiceContract] 2: public interface ILearnWcfService 3: { 4: [OperationContract(Name = "AddInt")] 5: int Add(int arg1, int arg2); 6: } Say I decided to add another interface with a similar add “feature”. 1: [ServiceContract] 2: public interface ILearnWcfServiceExtend : ILearnWcfService 3: { 4: [OperationContract(Name = "AddDouble")] 5: double Add(double arg1, double arg2); 6: } My class implementing the ILearnWcfServiceExtend ends up as: 1: public class LearnWcfService : ILearnWcfServiceExtend 2: { 3: public int Add(int arg1, int arg2) 4: { 5: return arg1 + arg2; 6: } 7:  8: public double Add(double arg1, double arg2) 9: { 10: return arg1 + arg2; 11: } 12: } Now when I consume this service and look at the proxy that gets generated, here’s what I see: 1: public interface ILearnWcfServiceExtend 2: { 3: [System.ServiceModel.OperationContractAttribute(Action="http://tempuri.org/ILearnWcfService/AddInt", ReplyAction="http://tempuri.org/ILearnWcfService/AddIntResponse")] 4: int AddInt(int arg1, int arg2); 5: 6: [System.ServiceModel.OperationContractAttribute(Action="http://tempuri.org/ILearnWcfServiceExtend/AddDouble", ReplyAction="http://tempuri.org/ILearnWcfServiceExtend/AddDoubleResponse")] 7: double AddDouble(double arg1, double arg2); 8: } Only the ILearnWcfServiceExtend gets ‘listed’ in the proxy class and not the (base interface) ILearnWcfService interface. But then to uniquely identify the operations that the service exposes, the Action and ReplyAction properties are set. So in the above example, the AddInt operation has the Action property set to ‘http://tempuri.org/ILearnWcfService/AddInt’ and the AddDouble operation has the Action property of ‘http://tempuri.org/ILearnWcfServiceExtend/AddDouble’. Similarly the ReplyAction properties are set corresponding to the namespace that they’re declared in. The ‘http://tempuri.org’ is chosen as the default namespace, since the Namespace property on the ServiceContract is not defined. The other thing is the service contract itself – the Add() method. You’ll see that in both interfaces, the method names are the same. As you might know, this is not allowed in WSDL-based environments, even though the arguments are of different types. This is allowed only if the Name attribute of the ServiceContract is set (as done above). This causes a change in the name of the service contract itself in the proxy class. See that their names are changed to AddInt / AddDouble respectively. Lesson learned: The interface hierarchy gets ‘flattened’ when the WCF service proxy class gets generated.

  Read the article

• Setting up shared connection

  - by Calvin Froedge

  I have a network that is connected to the internet via a switch connected to a router. I have it setup like this so I can work on the new network without causing problems on the old. Anyway, I'm trying to enable internet connection sharing. Internet comes to server like this: Modem - Router - Switch - Ubuntu 11.10 (Eth0) I want to share the connection through Eth1 (Eth1 - Managed Switch - Clients). Here is my config for /etc/network/interfaces: I have a DHCP server running on Eth1. Here is my config: ddns-update-style none; option domain-name "myserver.local"; option domain-name-servers 192.168.1.2, 8.8.8.8; default-lease-time 600; max-lease-time 7200; authoritative; subnet 192.168.1.0 netmask 255.255.255.0 { interface eth1; range 192.168.1.3 192.168.1.254; option routers 192.168.1.1; option subnet-mask 255.255.255.0; option broadcast-address 192.168.1.255; } Here is /etc/network/interfaces: # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet dhcp #Used for internal network auto eth1 iface eth1 inet static address 192.168.1.2 netmask 255.255.255.0 broadcast 192.168.1.255 network 192.168.1.0 Here is /etc/hosts: 127.0.0.1 localhost 127.0.1.1 myserver.isp.com server 192.168.1.2 server.myserver.local server myserver.local In /etc/sysctl.conf, I've set the following: net.ipv4.ip_forward=1 Finally, in /etc/rc.local, I've set the following: /sbin/iptables -P FORWARD ACCEPT /sbin/iptables --table nat -A POSTROUTING -o eth1 -j MASQUERADE When I ping 8.8.8.8 (google's DNS) from a client that is authenticated with my DHCP server (they have been assigned a local ip, like 192.168.1.10), I get a timeout. How can I debug this further to figure out where my problem is?

  Read the article

• Configuring Windows 2003 As A Router

  - by Sean M

  I am trying to configure a Windows 2003 server to act as a router, so that the two subnetworks that I'm dealing with can communicate with one another without NAT. I am mostly sure that I have configured Windows 2003 incorrectly, and I'm finding it very difficult to drill down through Google results to something helpful. I have a 192.168.1.0/24 network that is my "production" network (in the sense that I'm in trouble if I screw it up) and a 10.0.0.0/8 network that is my test network. The 192.168.1.0 network is ruled by a gateway whose routing table looks like this (my address redacted): The Windows 2003 server, "prime," is multihomed. Its network adapters are at 192.168.1.122, (as seen above), 10.0.0.1, and 10.0.0.2. I added the Routing and Remote Access role to it, and enabled LAN routing. I do not have it using RIP or other routing protocols. Its current routing table is shown below. To me, it looks like all of the right routes are there for traffic to pass between the 192.168.1.0 network and the 10.0.0.0 network. However, traffic does not pass. The 10.0.0.11 and .12 clients cannot be contacted from the 192.168.1.0 network. When I use traceroute to try to get to them, the trace gets to the Windows 2003 server's 192.168.1.122 address, then produces nothing but "* * *" timeouts. When I try to traceroute to 192.168.1.1 from a 10.0.0.0-network client, I get "destination host unreachable." However, I know that the routing is working at least a little, because from the 192.168.1.0 network, I can connect to the Windows server just fine by referring to it as 10.0.0.1. What static routes would allow me to contact 10.0.0.11 and .12 from the 192.168.1.0 network? Is it possible to tell the Windows server "since you are a DHCP/DNS server, you already know routes to get to machines that are getting IP addresses from you, please add those to your routing table" ? Will using RIP or OSPF on the Windows server actually be helpful in this situation?

  Read the article

• What can I do about rsync of large files killing my laptop's wifi connection

  - by David Dean

  When I run a rsync to backup my home folder over the network like so: rsync -avhz --progress --delete /home/dbdean/ [email protected]:/home/backups/david/ I seem to have problems with my quite large .VirtualBox/HardDisks/Windows XP.vdi file. Occasionally the wifi will silently fail (the transfer stops, and any other network access is broken). If I reconnect the wifi to my network before the transfer times out, it happily keeps going (and other network access is back), but I can't just leave it unattended most of the time, as I have to keep an eye on it. I'm guessing this is probably a bug in the wireless card related to a particularly high sustained volume of network usage, but I'm not really sure where to start with diagnosing this problem so that I can provide a good bug report. Or it could be something else, I guess. Any help would be appreciated. My network card is an Atheros Communications Inc. AR9285, as lspci -k shows: 43:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01) Subsystem: Hewlett-Packard Company Device 3040 Kernel driver in use: ath9k Kernel modules: ath9k

  Read the article

• Advice for programming a lobby for a network multiplayer game?

  - by Milo

  I'm working on learning network programming. I'm working on a simple card game. The basic idea is: Players enter the lobby Players see tables Players sit at an empty seat Once they sit, they do not need any information from the lobby, they see the card table and the data about the other players and so forth. I've programmed the server portion for the game itself. The clients connect to my server object and the server then receives and sends messages; quite simple. The tricky concepts for me are: What's a good way to run many tables at the same time? What's a good way to keep the lobby consistently updated for each person in the lobby (eg: MSG_TABLE_FILLED, 22) Ideally I'd like to have 1 server exe for all of this and to have to deal with multithreading as little as possible. I'm going to use the enet library. I was thinking that each time a game session starts, I push a new Game and I map the client IPs to that table, then I just route messages from those clients to that Game. Since enet supports channels I was thinking of using 2 channels per table, one for the game messages and one for in game chat. Would something like this work? Does anyone have any advice / design ideas for a game with a lobby and many tables? Is there a usual way this is done that I'm overlooking? Any conceptual ideas or even c/c++ code examples would be very helpful. Thanks

  Read the article

• Is encryption really needed for having network security? [closed]

  - by Cawas

  I welcome better key-wording here, both on tags and title. I'm trying to conceive a free, open and secure network environment that would work anywhere, from big enterprises to small home networks of just 1 machine. I think since wireless Access Points are the most, if not only, true weak point of a Local Area Network (let's not consider every other security aspect of having internet) there would be basically two points to consider here: Having an open AP for anyone to use the internet through Leaving the whole LAN also open for guests to be able to easily read (only) files on it, and even a place to drop files on Considering these two aspects, once everything is done properly... What's the most secure option between having that, or having just an encrypted password-protected wifi? Of course "both" would seem "more secure". But it shouldn't actually be anything substantial. I've always had the feeling using any kind of the so called "wireless security" methods is actually a bad design. I'm talking mostly about encrypting and pass-phrasing (which are actually two different concepts), since I won't even consider hiding SSID and mac filtering. I understand it's a natural way of thinking. With cable networking nobody can access the network unless they have access to the physical cable, so you're "secure" in the physical way. In a way, encrypting is for wireless what building walls is for the cables. And giving pass-phrases would be adding a door with a key. So, what do you think?

  Read the article

• How do I create a wifi network bridge with qemu on OS X?

  - by a paid nerd

  I grabbed a small FreeBSD live CD and QEMU, and I'm trying to bridge my Mac OS X 10.8 wifi connection so that the guest OS is available on my LAN. However, the guest OS never gets a DHCP lease. This works perfectly with VirtualBox in their "bridged" network mode, so I know it can be done. I need to get it working with QEMU because VirtualBox doesn't support the architecture that I need for this project. Here's what I've done so far based on hours of googling: Installed TUNTAP for OS X Told OS X to supposedly forward all packets, even ARP: (NOTE: This doesn't appear to work.) $ sudo sysctl -w net.inet.ip.forwarding=1 $ sudo sysctl -w net.link.ether.inet.proxyall=1 $ sudo sysctl -w net.inet.ip.fw.enable=1 Created a bridge: $ sudo ifconfig bridge0 create $ sudo ifconfig bridge0 addm en0 addm tap0 $ sudo ifconfig bridge0 up $ ifconfig bridge0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500 ether ac:de:xx:xx:xx:xx Configuration: priority 0 hellotime 0 fwddelay 0 maxage 0 ipfilter disabled flags 0x2 member: en0 flags=3<LEARNING,DISCOVER> port 4 priority 0 path cost 0 member: tap0 flags=3<LEARNING,DISCOVER> port 8 priority 0 path cost 0 tap0: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> mtu 1500 ether ca:3d:xx:xx:xx:xx open (pid 88244) Started tcpdump with -I in the hopes that it enables promiscuous mode on the wifi device: $ sudo tcpdump -In -i en0 Run QEMU using the bridged network instructions: $ qemu-system-x86_64 -cdrom mfsbsd-9.2-RELEASE-amd64.iso -m 1024 \ -boot d -net nic -net tap,ifname=tap0,script=no,downscript=no But the guest system never gets a DHCP lease: If I tcpdump -ni tap0, I see lots of traffic from the wireless network. But if I tcpdump -ni en0, I don't see any DHCP traffic from the QEMU guest OS. Any ideas? Update 1: I tried sudo defaults write "/Library/Preferences/SystemConfiguration/com.apple.Boot" "Kernel Flags" "net.inet.ip.scopedroute=0" and rebooting per this mailing list suggestion, but this didn't help. In fact, it made VirtualBox bridged mode stop working.

  Read the article

• Oracle Support Customers take note My Oracle Support Flash is set to Retire

  - by user12244613

  Take Action – My Oracle Support Flash User Interface Set to Retire On July 13, 2012, Oracle plans to upgrade the HTML interface with additional functionality that will allow those users still remaining on the Flash-based interface to switch over to the HTML version. Although the Flash-based user interface will remain available for a brief period following the upgrade, we encourage you to begin using the new HTML version sooner. Find out when you should make the switch! Read complete communication to Flash users

  Read the article

• How should I set up my Hyper-V server and network topology?

  - by Daniel Waechter

  This is my first time setting up either Hyper-V or Windows 2008, so please bear with me. I am setting up a pretty decent server running Windows Server 2008 R2 to be a remote (colocated) Hyper-V host. It will be hosting Linux and Windows VMs, initially for developers to use but eventually also to do some web hosting and other tasks. Currently I have two VMs, one Windows and one Ubuntu Linux, running pretty well, and I plan to clone them for future use. Right now I'm considering the best ways to configure developer and administrator access to the server once it is moved into the colocation facility, and I'm seeking advice on that. My thought is to set up a VPN for access to certain features of the VMs on the server, but I have a few different options for going about this: Connect the server to an existing hardware firewall (an old-ish Netscreen 5-GT) that can create a VPN and map external IPs to the VMs, which will have their own IPs exposed through the virtual interface. One problem with this choice is that I'm the only one trained on the Netscreen, and its interface is a bit baroque, so others may have difficulty maintaining it. Advantage is that I already know how to do it, and I know it will do what I need. Connect the server directly to the network and configure the Windows 2008 firewall to restrict access to the VMs and set up a VPN. I haven't done this before, so it will have a learning curve, but I'm willing to learn if this option is better long-term than the Netscreen. Another advantage is that I won't have to train anyone on the Netscreen interface. Still, I'm not certain if the capabilities of the Windows software firewall as far as creating VPNs, setting up rules for external access to certain ports on the IPs of Hyper-V servers, etc. Will it be sufficient for my needs and easy enough to set up / maintain? Anything else? What are the limitations of my approaches? What are the best practices / what has worked well for you? Remember that I need to set up developer access as well as consumer access to some services. Is a VPN even the right choice?

  Read the article

• How to configure a tun interface on Linux for SSH port forwarding?

  - by sarshad

  I am trying to forward port 139 from a Windows machine to my Ubuntu SSH server on a tun interface with the ip address 10.0.0.1. This is so that I can access the windows shares on the machine on my Ubuntu server, through the reverse tunnel. I can forward ports to 127.0.0.1, but not to 10.0.0.1. On windows I am using the Tunnelier ssh client. On my Ubuntu server, the following message is printed in auth.log: Received disconnect from 124.109.51.154: 11: Server denied request for client-side server-2-client forwarding on 10.0.0.1:139. So far i have tried the following settings: GatewayPorts yes PermitTunnel yes AllowTcpForwarding yes in the /etc/ssh/sshd_config file, but it did not work. I set up the tun like this: sudo tunctl -t loc_0 -u myusername sudo ifconfig loc_0 inet 10.0.0.1 netmask 255.255.255.0 up The settings in the Tunneler ssh client should not matter because I can forward port 139 successfully to the Microsoft Loopback Adapter on a Windows machine running the WinSSHD server. Versions: Windows is XP SP3, Ubuntu is 10.10. Update: I tried to forward the port to a number greater than 1024 mentioning the IP address of the tun, and it successfully connected but the forwarding was done on 127.0.0.1 instead of the tun's IP address 10.0.0.1. So there are two separate problems now, when connecting from the Windows machine: 1) Forwarding on ports less than 1024 is probably being denied. How can we allow that on the server? 2) Forwarding is done only on 127.0.0.1 even if I mention 10.0.0.1 which is the tun's IP address. Another attempt: I also tried to forward port 22 of a Linux machine to the tun's port 55567. It showed success. But when I tried to ssh into that port using both local addresses, on the Linux machine in its debug display I got the error Connection failed: no route to host when using 127.0.0.1 to connect and simply Connection refused when using the tun's IP address. So the tun is not getting the forwarded port no matter we connect from a Windows client or a Linux client.

  Read the article

• lxc containers fail to autoboot in 14.04 trusty using 'lxc.start.auto = 1'

  - by user273046

  In trusty 14.04 containers fail to autoboot despite all settings being set as 14.04 requires. They show all as STOPPED I have correctly configured 2 LXC containers: calypso encelado They run perfectly if I run sudo lxc-autostart then sudo lxc-ls --fancy results in: ubuntu@saturn:/etc/init$ sudo lxc-ls --fancy NAME STATE IPV4 IPV6 AUTOSTART calypso RUNNING 192.168.1.161 - YES encelado RUNNING 192.168.1.162 - YES The problem is trying to run them at boot. I have at: /var/lib/lxc/calypso/config: # Template used to create this container: /usr/share/lxc/templates/lxc-download # Parameters passed to the template: # For additional config options, please look at lxc.conf(5) # Distribution configuration lxc.include = /usr/share/lxc/config/ubuntu.common.conf lxc.arch = x86_64 # Container specific configuration lxc.rootfs = /var/lib/lxc/calypso/rootfs lxc.utsname = calypso # Network configuration lxc.network.type = veth lxc.network.flags = up #lxc.network.link = lxcbr0 lxc.network.link = br0 lxc.network.hwaddr = 00:16:3e:64:0b:6e # Assegnazione IP Address lxc.network.ipv4 = 192.168.1.161/24 lxc.network.ipv4.gateway = 192.168.1.1 # Autostart lxc.start.auto = 1 lxc.start.delay = 5 lxc.start.order = 100 and I have LXC_AUTO="false" as required inside /etc/default/lxc: LXC_AUTO="false" USE_LXC_BRIDGE="false" # overridden in lxc-net [ -f /etc/default/lxc-net ] && . /etc/default/lxc-net LXC_SHUTDOWN_TIMEOUT=120 Any idea on why the containers don't start at boot? At reboot they are always in the STOPPED state: ubuntu@saturn:~$ sudo lxc-ls --fancy NAME STATE IPV4 IPV6 AUTOSTART calypso STOPPED - - YES encelado STOPPED - - YES and then again they can be started manually, using sudo lxc-autostart

  Read the article

• Unable to access the WCF service over VPN!

  - by kurozakura

  Heres the scenario, im on a network A, and i use a vpn client to connect network B to access the webservice which can be accessed in network B.Even though im connect to network B , im unable to access the webservice link.Do i need to configure any settings. But if u r originally in network B and even though if u have connected to network A using vpn client, im able to access the webservice link. But the other way isnt working.

  Read the article

• Why would accessing photos over a network be a problem for Digikam?

  - by Shedeki

  Digikam has always worked nicely for me. I recently setup a Synology DiskStation (DS212+) and moved all my pictures to it, keeping them in an encrypted folder. I mount that folder using cifs, as some bug prevents eCryptfs and NFS from working together. This has led Digikam to being incredibly slow. Startup takes a very long time (several minutes for 41779 items, 123.8GB) but worse is how long it takes Digikam to write files. I like using Digikams import feature to copy new images from my camera to the hard drive because it checks for duplicates as well as creating a clear folder structure according to the dates the images were taken. Since I moved to using the network drive Digikam takes about 5 to 10 times as long to import photos than it did before. Saving modified or converted images takes equally long. What I am looking for is a way to help Digikam speed things up or an alternative piece of software (I have never liked Digikam being so very much KDEish…). There are just so many features that only Digikam seems to combine, e.g.: Batch processing. Respects existing folder structure. Does not mess up files for other applications. *.NEF support. Caches thumbnails in a clean way.

  Read the article

< Previous Page | 251 252 253 254 255 256 257 258 259 260 261 262  | Next Page >