Search Results

Search found 94497 results on 3780 pages for 'text file'.

Page 259/3780 | < Previous Page | 255 256 257 258 259 260 261 262 263 264 265 266  | Next Page >

  • Strange network issue (ZIP file fails CRC test over VPN)

    - by Joe Schmoe
    We have a server in the office running Windows Server 2003 Our office is connected to our datacenter via hardware VPN (Linksys RV082 router in the office to CISCO router in the datacenter). There is a job that runs on the server in the office that does following: ZIP certain files from the server using 7Zip, copy ZIP file to a network share in the office and verify ZIP integrity, copy ZIP file to a network share in the data center and verify ZIP integrity. Problem is - verifying ZIP integrity for the file in the data center always fails. However, if I run 7Zip on the server in data center that exposes that share ZIP file verifies just fine, so it is not actually corrupted during copy operation. Additionally, I tried running ZIP on other computers in the office to verify ZIP file on datacenter file share and it verifies OK. I tried plugging server to the same network port where my workstation is connected using different cable (my workstation doesn't exhibit this problem) and ZIP verification still fails. So the problem is local to that specific server. On network adapter properties for the server in question there is no "Advanced" tab where one can usually configure a lot of network settings. Network card driver is up to date (Windows Update doesn't find anything newer and Lenovo website doesn't have any drivers for Windows 2003 for this computer model). Is there any other way to configure network setting via command line? What settings could be relevant to this problem?

    Read the article

  • Reading variable with double float precision from a text file with gnuplot

    - by user3636322
    I have a text file, containing data in 3 columns like below: 0.0100000000 | 0.0058077299 | -0.0000000288 0.0110000000 | 0.0075128707 | -0.0000000373 0.0120000000 | 0.0093579693 | -0.0000000465 I want to get the variables from this file in gnuplot and use them to draw graphs: What I exactly do is like below (e.g: to pick the variable from row 2 column 3): ii= 2 a_0 = system("awk '{ if (NR == " . ii . ") printf \"%f\", $3}' " .datafile) a_0 = a_0+0. but what is written as a_0 is zero! How can I increase the precision to get the exact value?

    Read the article

  • Python - read numbers from text file and put into list

    - by user1647372
    So like the title says im starting to learn some python and im having trouble picking up on this technique. What I need to accomplish is to read in some numbers and store them in a list. The text file looks like the following: 0 0 3 50 50 100 4 20 Basically these are coordinates and directions to be used for python's turtle to make shapes. I got that part down the only problem is getting them in a correct format. So what I can not figure out is how to get those numbers from the file into [ [0, 0, 3, 50], [50, 100, 4, 20] ] A list, with each four coordinates being a list in that one big list. Heres my attempt but it as I said I need some help - thank you. polyShape=[] infile = open(name,"r") num = int(infile.readline(2)) while num != "": polyShape.append(num) num = int(infile.readline(2)) infile.close()

    Read the article

  • SQL Server FTS: possible to get information how/why rows were matched?

    - by jimmy_keen
    Is it possible to get the information why/how given row returned by FTS query was matched (or which substring caused row to match)? For example, consider simpliest table with id and text columns, with FTS index on the later one. SELECT * FROM Example WHERE CONTAINS(text, 'FORMSOF(INFLECTIONAL, jump)'); This examplary query could return, say row {1, 'Jumping Jack'}. Now, is it possible to somehow get information that this very row was matched because of 'Jumping' word? It doesn't even have to be exact information, more of a which substring caused row to match. Why I'm asking - I got C# app that builds up those queries basing on user input (keywords to search for), and I need the very basic information why/how row was matched back, to use further in C# code. If it's not possible, any alternatives?

    Read the article

  • Removing a text block from a file : sed ?

    - by user555338
    Hi, Following an attack, I need to remove 4 lines of text added to .htaccess files in my site, and was thinking SED would be the way to go, but cannot see how in spire of many attempts. The added lines are RewriteEngine On RewriteCond %{HTTP_REFERER} ^http:// RewriteCond %{HTTP_REFERER} !%{HTTP_HOST} RewriteRule . http://targeturlhere.net/%{REMOTE_ADDR} I managed to create the script to remove added htaccess files containing those lines only, but for existing htaccess files in which that was appended I have to edit the file and cannot delete it. I cannot just remove line by line nor use "RewriteEngine On" as the start marker, as this instruction "RewriteEngine On" is sometimes legitimate elsewhere in the file. In most cases those lines are the last, but I guess in other files they could be in the middle, so I was trying to remove exactly that block - and have a script I could reuse in a similar case. (Edit: my 4 lines are below one another, no blank line in between but the editor here seems to either show no breakline, or one adding a blank line) Any hint or tip ? Thanks.

    Read the article

  • Edit very large sql dump/text file (on linux)

    - by geo
    I have to import a large mysql dump (up to 10G). However the sql dump already predefined with a database structure with index definition. I want to speed up the db insert by removing the index and table definition. That means I have to remove/edit the first few lines of a 10G text file. What is the most efficient way to do this on linux? Programs that require loading the entire file into RAM will be an overkill to me.

    Read the article

  • MaxTotalSizeInBytes - Blind spots in Usage file and Web Analytics Reports

    - by Gino Abraham
    Originally posted on: http://geekswithblogs.net/GinoAbraham/archive/2013/10/28/maxtotalsizeinbytes---blind-spots-in-usage-file-and-web-analytics.aspx http://blogs.msdn.com/b/sharepoint_strategery/archive/2012/04/16/usage-file-and-web-analytics-reports-with-blind-spots.aspx In my previous post (Troubleshooting SharePoint 2010 Web Analytics), I referenced a problem that can occur when exceeding the daily partition size for the LoggingDB, which generates the ULS message “[Partition] has exceeded the max bytes”. Below, I wanted to provide some additional info on this particular issue and help identify some options if this occurs. As an aside, this post only applies if you are missing portions of Usage data - think blind spots on intermittent days or user activity regularly sparse for the afternoon/evening. If this fits your scenario - read on. But if Usage logs are outright missing, go check out my Troubleshooting post first.  Background on the problem:The LoggingDB database has a default maximum size of ~6GB. However, SharePoint evenly splits this total size into fixed sized logical partitions – and the number of partitions is defined by the number of days to retain Usage data (by default 14 days). In this case, 14 partitions would be created to account for the 14 days of retention. If the retention were halved to 7 days, the LoggingDBwould be split into 7 corresponding partitions at twice the size. In other words, the partition size is generally defined as [max size for DB] / [number of retention days].Going back to the default scenario, the “max size” for the LoggingDB is 6200000000 bytes (~6GB) and the retention period is 14 days. Using our formula, this would be [~6GB] / [14 days], which equates to 444858368 bytes (~425MB) per partition per day. Again, if the retention were halved to 7 days (which halves the number of partitions), the resulting partition size becomes [~6GB] / [7 days], or ~850MB per partition.From my experience, when the partition size for any given day is exceeded, the usage logging for the remainder of the day is essentially thrown away because SharePoint won’t allow any more to be written to that day’s partition. The only clue that this is occurring (beyond truncated usage data) is an error such as the following that gets reported in the ULS:04/08/2012 09:30:04.78    OWSTIMER.EXE (0x1E24)    0x2C98    SharePoint Foundation    Health    i0m6     High    Table RequestUsage_Partition12 has 444858368 bytes that has exceeded the max bytes 444858368It’s also worth noting that the exact bytes reported (e.g. ‘444858368’ above) may slightly vary among farms. For example, you may instead see 445226812, 439123456, or something else in the ballpark. The exact number itself doesn't matter, but this error message intends to indicates that the reporting usage has exceeded the partition size for the given day.What it means:The error itself is easy to miss, which can lead to substantial gaps in the reporting data (your mileage may vary) if not identified. At this point, I can only advise to periodically check the ULS logs for this message. Down the road, I plan to explore if [Developing a Custom Health Rule] could be leveraged to identify the issue (If you've ever built Custom Health Rules, I'd be interested to hear about your experiences). Overcoming this issue also poses a challenge, with workaround options including:Lower the retentionBecause the partition size is generally defined as [max size] / [number of retention days], the first option is to lower the number of days to retain the data – the lower the retention, the lower the divisor and thus a bigger partition. For example, halving the retention from 14 to 7 days would halve the number of partitions, but double the partition size to ~850MB (e.g. [6200000000 bytes] / [7 days] = ~850GB partitions). Lowering it to 2 days would result in two ~3GB partitions… and so on.Recreate the LoggingDB with an increased sizeThe property MaxTotalSizeInBytes is exposed by OM code for the SPUsageDefinition object and can be updated with the example PowerShell snippet below. However, updating this value has no immediate impact because this size only applies when creating a LoggingDB. Therefore, you must create a newLoggingDB for the Usage Service Application. The gotcha: this effectively deletes all prior Usage databecause the Usage Service Application can only have a single LoggingDB.Here is an example snippet to update the "Page Requests" Usage Definition:$def=Get-SPUsageDefinition -Identity "page requests" $def.MaxTotalSizeInBytes=12400000000 $def.update()Create a new Logging database and attach to the Usage Service Application using the following command: Get-spusageapplication | Set-SPUsageApplication -DatabaseServer <dbServer> -DatabaseName <newDBname> Updated (5/10/2012): Once the new database has been created, you can confirm the setting has truly taken by running the following SQL Query (be sure to replace the database name in the following query with the name provided in the PowerShell above)SELECT * FROM [WSS_UsageApplication].[dbo].[Configuration] WITH (nolock) WHERE ConfigName LIKE 'Max Total Bytes - RequestUsage'

    Read the article

  • perl comparing 2 data file as array 2D for finding match one to one [migrated]

    - by roman serpa
    I'm doing a program that uses combinations of variables ( combiData.txt 63 rows x different number of columns) for analysing a data table ( j1j2_1.csv, 1000filas x 19 columns ) , to choose how many times each combination is repeated in data table and which rows come from (for instance, tableData[row][4]). I have tried to compile it , however I get the following message : Use of uninitialized value $val in numeric eq (==) at rowInData.pl line 34. Use of reference "ARRAY(0x1a2eae4)" as array index at rowInData.pl line 56. Use of reference "ARRAY(0x1a1334c)" as array index at rowInData.pl line 56. Use of uninitialized value in subtraction (-) at rowInData.pl line 56. Modification of non-creatable array value attempted, subscript -1 at rowInData.pl line 56. nothing This is my code: #!/usr/bin/perl use strict; use warnings; my $line_match; my $countTrue; open (FILE1, "<combiData.txt") or die "can't open file text1.txt\n"; my @tableCombi; while(<FILE1>) { my @row = split(' ', $_); push(@tableCombi, \@row); } close FILE1 || die $!; open (FILE2, "<j1j2_1.csv") or die "can't open file text1.txt\n"; my @tableData; while(<FILE2>) { my @row2 = split(/\s*,\s*/, $_); push(@tableData, \@row2); } close FILE2 || die $!; #function transform combiData.txt variable (position ) to the real value that i have to find in the data table. sub trueVal($){ my ($val) = $_[0]; if($val == 7){ return ('nonsynonymous_SNV'); } elsif( $val == 14) { return '1'; } elsif( $val == 15) { return '1';} elsif( $val == 16) { return '1'; } elsif( $val == 17) { return '1'; } elsif( $val == 18) { return '1';} elsif( $val == 19) { return '1';} else { print 'nothing'; } } #function IntToStr ( ) , i'm not sure if it is necessary) that transforms $ to strings , to use the function <eq> in the third loop for the array of combinations compared with the data array . sub IntToStr { return "$_[0]"; } for my $combi (@tableCombi) { $line_match = 0; for my $sheetData (@tableData) { $countTrue=0; for my $cell ( @$combi) { #my $temp =\$tableCombi[$combi][$cell] ; #if ( trueVal($tableCombi[$combi][$cell] ) eq $tableData[$sheetData][ $tableCombi[$combi][$cell] - 1 ] ){ #if ( IntToStr(trueVal($$temp )) eq IntToStr( $tableData[$sheetData][ $$temp-1] ) ){ if ( IntToStr(trueVal($tableCombi[$combi][$cell]) ) eq IntToStr($tableData[$sheetData][ $tableCombi[$combi][$cell] -1]) ){ $countTrue++;} if ($countTrue==@$combi){ $line_match++; #if ($line_match < 50){ print $tableData[$sheetData][4]." "; #} } } } print $line_match." \n"; }

    Read the article

  • Create files on C:\ root gives error 0x80070522

    - by Bryan
    One of our customers has just found a problem when trying to create a file on the root of the C:\ Drive, on a Windows 7 Professional PC. I know they shouln't be keeping files here, but there is a valid reason in this case, so I've relaxed the security on the root of C:\ by giving the group 'users' modify permission. Before I relaxed the security, the user was receiving 'access denied', but now they are receiving the message: An unexpected error is keeping you from creating the file. If you continue to recieve this error, you can use the error code to search for help with this problem. Error 0x80070522: A required priviledge is not held by the client. Googling for this suggests that it is caused by UAC, but how can I get round this when the user doesn't have admin rights on their PC?

    Read the article

  • Windows Server 2008 CMD Task Schedule not running

    - by Jonathan Platovsky
    I have a BAT/CMD file that when run from the command prompt runs completely. When I run it through the Task Scheduler it partially runs. Here is a copy of the file cd\sqlbackup ren Apps_Backup*.* Apps.Bak ren Apps_Was_Backup*.* Apps_Was.Bak xcopy /Y c:\sqlbackup\*.bak c:\sqlbackup\11\*.bak xcopy /y c:\sqlbackup\*.bak \\igweb01\c$\sqlbackup\*.bak Move /y c:\sqlbackup\*.bak "\\igsrv01\d$\sql backup\" The last two lines do not run when the task scheduler calls it. But again, work when manually run from the command line. All the local sever commands run but when it comes to the last two lines where it goes to another server then it does not work.

    Read the article

  • IIS6 Indexing Service indexing asp.net codebehind (.aspx.cs) files

    - by Patrick F
    I've setup a few catalogs on an Windows Server 2003 IIS6 install, each tracking files within a website. In the Properties - Generation Dialog for each catalog, 'Index files with unknown extensions' is turned OFF. 'Inherit above settings from Service' in that dialog is also turned off. However, the index is returning results for .cs files, along with abstracts for those files. I've emptied and restarted the catalogs but the files are still appearing. My understanding was the Indexing Service would by default only index HTML, ASCII, and Office Documents. What's going on?

    Read the article

  • Save error in jEdit

    - by wantoknow
    Every time I try to save something in my jEdit, it returns an error with the message: The following I/O operation could not be completed (C:\Program Files\jEdit\Untitled-1: Cannot save: java.io.FileNotFoundException: C:\Program Files\jEdit#Untitled-1#save# (Access is denied)) What could be wrong?

    Read the article

  • Can't copy files with 'additional permissions' to ext4 drive -- files that have @ after permissions,

    - by 99miles
    I am copying files from Snow Leopard to a mounted ext4 share via Samba, that's on a Fedora machine. Some files cannot be copied, and give this error: The operation can’t be completed because you don’t have permission to access some of the items. I've noticed that the files that can't be copied have an @ at the end of their permissions whien I do 'ls -l' in the command line. For example, I can copy the second file but not the first: -rwxrwxrwx@ 1 miles staff 1448 May 14 22:55 test.txt -rw-r--r-- 1 miles staff 136 Apr 5 17:06 image.psd.zip From what I've found, the @ means the file has 'additional properties'. Does anyone know how I can resolve this issue so I can copy the files to the fileshare?? Thanks!

    Read the article

  • Why is the XML DTD not found by the browser

    - by hyperuser
    When I load my XML file in a browser, it complains there is 'no style information': "This XML file does not appear to have any style information associated with it. The document tree is shown below." So I wrote an external DTD, then an internal DTD, but keep getting the same 'no style information' error. It doesn't even show the DTD! What am I doing wrong? <?xml version="1.0"?> <!DOCTYPE fotos [ <!ELEMENT fotos (titel,auteur)> <!ELEMENT titel (#PCDATA)> <!ELEMENT auteur (#PCDATA)> ]> <fotos> <titel>titel1</titel> <auteur>jan</auteur> </fotos>

    Read the article

  • Recovering database files from a corrupted VHD

    - by Apocalypse9
    We have a SQL server hosted on a virtual machine. Our hosting company updated/restarted the server and for some reason the virtual machines became unbootable. We've spoken to Microsoft and used a few higher level tools to attempt to recover the virtual machines but were unsuccessful. In browsing the file system the database folder doesn't even appear. I'm wondering if there are any lower level tools that might be able to find and copy the database files. As far as I know the physical hard drive is ok, so I'm hoping there may be some way to recover the files themselves even if the rest of the virtual machine file-system is a loss. Obviously we're in a bit of a bind, and any help/ suggestions are very much appreciated.

    Read the article

  • Scheduled task to map a network drive runs, but doesn't map the drive

    - by bikefixxer
    I have a task set up to run whenever the computer is logged onto that deletes all network folders and maps a network drive. Here is what is in the batch file: @echo off net use * /delete /y net use b: \\Server\Share /user:DOMAIN\Username password exit When the computer is restarted or logged off and back on, the task runs fine (according to the scheduled tasks window saying when it ran last) but the mapped drive doesn't show up. I'll open the command prompt and type "net use" and it simply says "There are no entries in the list". If I then right click on the task and run it, it works and the mapped drive shows up. I've checked the log and nothing shows up. I've tried adding a timer in the batch file so it waits 10 seconds (ping 1.1.1.1 -n 1 -w 10000nul) thinking that maybe the network wasn't connected, but that didn't work. What else can I try? Thanks!

    Read the article

  • Can connect to Samba server but cannot access shares?

    - by jlego
    I have setup a stand-alone box running Fedora 16 to use as a file-sharing and web development server. Needs to be able to share files with a PC running Windows 7 and a Mac running OSX Snow Leopard. I've setup Samba using the Samba configuration GUI tool. Added users to Fedora and connected them as Samba users (which are the same as the Windows and Mac usernames and passwords). The workgroup name is the same as the Windows workgroup. Authentication is set to User. I've allowed Samba and Samba client through the firewall and set the ethernet to a trusted port in the firewall. Both the Windows and Mac machines can connect to the server and view the shares, however when trying to access the shares, Windows throws error 0x80070035 " Windows cannot access \SERVERNAME\ShareName." Windows user is not prompted for a username or password when accessing the server (found under "Network Places"). This also happens when connecting with the IP rather than the server name. The Mac can also connect to the server and see the shares but when choosing a share gives the error "The original item for ShareName cannot be found." When connecting via IP, the Mac user is prompted for username and password, which when authenticated gives a list of shares, however when choosing a share to connect to, the error is displayed and the user cannot access the share. Since both machines are acting similarly when trying to access the shares, I assume it is an issue with how Samba is configured. smb.conf: [global] workgroup = workgroup server string = Server log file = /var/log/samba/log.%m max log size = 50 security = user load printers = yes cups options = raw printcap name = lpstat printing = cups [homes] comment = Home Directories browseable = no writable = yes [printers] comment = All Printers path = /var/spool/samba browseable = yes printable = yes [FileServ] comment = FileShare path = /media/FileServ read only = no browseable = yes valid users = user1, user2 [webdev] comment = Web development path = /var/www/html/webdev read only = no browseable = yes valid users = user1 How do I get samba sharing working? UPDATE: Before this box I had another box with the same version of fedora installed (16) and samba working for these same computers. I started up the old machine and copied the smb.conf file from the old machine to the new one (editing the share definitions for the new shares of course) and I still get the same errors on both client machines. The only difference in environment is the hardware and the router. On the old machine the router received a dynamic public IP and assigned dynamic private IPs to each device on the network while the new machine is connected to a router that has a static public IP (still dynamic internal IPs though.) Could either one of these be affecting Samba? UPDATE 2: As the directory I am trying to share is actually an entire internal disk, I have tried to things: 1.) changing the owner of the mounted disk from root to my user (which is the same username as on the Windows machine) 2.) made a share that only included one of the folders on the disk instead of the entire disk with my user again as the owner. Both tests failed giving me the same errors regarding the network address. UPDATE 3: Not sure exactly what I did, but now whenever I try to connect to the share on the Windows 7 client I am prompted for my username and password. When I enter the correct credentials I get an access denied message. However I did notice that under the login box "domain: WINDOWS-PC-NAME" is listed. I believe this could very well be the problem. Any suggestions? UPDATE 4: So I've completely reinstalled Fedora and Samba now. I've created a share on the first harddrive (one fedora is installed on) and I can access that fine from Windows. However when I try to share any data on the second disk, I am receiving the same error. This I believe is the problem. I think I need to change some things in fstab or fdisk or something. UPDATE 5: So in fstab I mapped the drive to automount in a folder which works correctly. I also added the samba_share_t SElinux label to the mountpoint directory which now allows me to access the shares on the Windows machine, however I cannot see any of the files in the directory on the windows machine. (They are there, I can see them in the fedora file browser locally) UPDATE 6: Figured it out. See answer below

    Read the article

  • find files where group permissions equal user permissions

    - by Jayen
    Is it possible to do something like find -perm g=u? I say "like" because -perm mode requires mode to specify all the bits, not just g, and because I can't put u on the right side of the =, like I can with the chmod command: you can specify exactly one of the letters ugo: the permissions granted to the user who owns the file (u), the permissions granted to other users who are members of the file's group (g), and the permissions granted to users that are in neither of the two preceding categories (o). At the moment, I'm doing find | xargs -d \\n ls -lartd | egrep '^.(...)\1 which is just ugly. Thanks.

    Read the article

  • Excel 2003 opening files on network

    - by Luke
    The network is laid out with an XP Pro computer as the server hosting files, then 3 XP computers connecting to it for filesharing, all on it's own router. One computer can open .xls files no problem, and she runs Office XP. The other two computers run Office 2003, and cannot open any shared files by double-clicking them, or by selecting File-Open in Excel. If the file gets copied to the local computer, it opens instantly. I have tried disabling the AV on all computers, disabling the Windows firewall, and doublechecking permissions on the server. I have also tried disabling DDE, but that doesn't help at all, just like Tools-Options-unticking Ignore other applications. Any ideas? This apparently started a couple days ago

    Read the article

  • Outlook 2003: open email in edit mode

    - by Eleasar
    Is there some macro (or C# code) to open an email automatically in edit mode? I know i can double click an email item, go to edit and edit message - but can i do this to automatically open an email in this way? Or even better if i could show emails in edit mode in the reading pane?

    Read the article

  • Configuring SMB shares in OS X

    - by Craig Walker
    I'm at my wit's end trying to control SMB file sharing on my Mac. (OS X 10.5 Leopard). I want to do something fairly simple: share a particular (non-home, non-Public) folder over my my SMB/Windows network with two users (accounts are local to my Mac), and share no other folders with anyone. The instructions on the internet are fairly straightforward: add the folders to be shared to the File Sharing panel of the Sharing System Preferences pane: ..and ensure that I'm sharing through SMB: However, when I actually try to connect via a SMB client (Windows XP in this case), the share does not appear. I see my home directory, "Macintosh HD", and my printers, but not the folder I just shared. I ensured that the underlying directory had the proper permissions (since this seems to affect share visibility) and that the "Shared Folder" checkbox was checked: ...but this didn't have any effect. I checked /etc/smb.conf but there was nothing obviously out of place there. I've also restarted smbd and rebooted. What else should I be looking for?

    Read the article

  • how to grep ip from ifconfig output

    - by Registered User
    Following is my ifconfig output eth0 Link encap:Ethernet UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:28 Base address:0x2000 eth1 Link encap:Ethernet inet addr:192.168.1.2 Bcast:192.168.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:36497 errors:0 dropped:0 overruns:0 frame:14515 TX packets:44884 errors:1352 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:20781745 (20.7 MB) TX bytes:17776225 (17.7 MB) Interrupt:17 Base address:0xc000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:12 errors:0 dropped:0 overruns:0 frame:0 TX packets:12 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:720 (720.0 B) TX bytes:720 (720.0 B) virbr0 Link encap:Ethernet inet addr:192.168.122.1 Bcast:192.168.122.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:24 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:4416 (4.4 KB) vmnet1 Link encap:Ethernet inet addr:192.168.185.1 Bcast:192.168.185.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:24 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) vmnet8 Link encap:Ethernet inet addr:192.168.207.1 Bcast:192.168.207.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:25 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) I want to do some thing grep that I see the IP corresponding to each LAN card? Is that possible? How can it be achieved?

    Read the article

  • Active Desktop cannot be restored on Win XP

    - by Phil.Wheeler
    This is more of a major annoyance than anything that's stopping me from doing my work, but I somehow seem to have had Active Desktop on my work XP machine get corrupted and now can't get it back working again. I've tried browsing to C:\Documents and Settings\%my-user-name%\Application Data\Microsoft\Internet Explorer and changing, deleting or replacing the Desktop.htt file, but it's not achieving anything. The error I was previously getting when trying to click the "Restore my active desktop" button was: Internet Explorer Script Error An error has occurred in the script on this page. Line: 65 Char: 1 Error: Object doesn't support this action Code: 0 URL: file://C:/Documents%20and%20Settings//Application %20Data/Microsoft/Internet%20Explorer/Desktop.htt Any ideas?

    Read the article

< Previous Page | 255 256 257 258 259 260 261 262 263 264 265 266  | Next Page >