Search Results

Search found 30658 results on 1227 pages for 'off screen'.

Page 261/1227 | < Previous Page | 257 258 259 260 261 262 263 264 265 266 267 268  | Next Page >

• Can Current Backflow from Powered Hub's Adapter & cause PC Damage?

  - by SuperUserMan

  Getting this short: Can current flow from a powered USB hub's power adapter (lying 10 Meter away) back to computer via usb port and cause damage to Computer components like mobo, etc? What should be my concerns? Using a 2 Amp 5V Power adapter to power a 10m Long Active Repeater USB extension cable with 4 port HUB & plugging into PC's Front port, causes PC Chassis fan to keep running (thought slower than regular speed) Front Chassis HDD & power LED to turn on (though bit dim) may be other things which i cant detect/see at chip level, in motherboard?? All this even after PC is shut down (bit scary) More detail (in case still want to read): To run 4 High power (needing 450 mAmps) Wifi Adapters, far away from PC, Bought Active Repeater USB Extension Cable with 4 Ports & power port at far end http://www.ebay.com/itm/33FT-USB-2-0-Male-to-Female-Extension-Cable-Hub-Splitter-Adapter-with-4-USB-Port-/390846115254 Then added a locally bought 2 Amp 240V AC to 5V DC Power Adapter and plugged into USB hub which is a part of & situated at far end of a 10 Meter Active Repeater usb extension cable. Even 4 Wifi Adapters run fine (appear to) using this setup, but running chassis fan, dimly lighted Power & HDD LED, even when PC is switched off is bit scary and surely mean 5V & some current is flowing all though that 10 meter extension cable into my USB port & powering stuff. Can this cause damage? and what should be my concerns. Of course I can't switch off the power adapter (lying 10 meters away from PC) every time I switch off my PC to prevent this.

  Read the article

• CentOS Installation on a Cisco MCS 7800

  - by William

  I'm having some problems installing CentOS 5.5 Final (i386) onto my server, a Cisco MCS 7800. The problem comes very early into the installation. When the welcome screen comes up and gives you the option on how to boot into the DVD, I'll press enter to go into the graphical installer. The screen will then have a blinking cursor in the top left of the screen and will never go away (I thought that it just might need time but I let it sit for over 5 hours). I then booted into it again and tried using Linux Text thinking it was a problem with the graphical installer. That didn't work, same problem. Then I tried a DVD of RHEL 5 and got the same problem, both graphical and Linux text. At this point I think it's a hardware problem. The server has 2GB of ECC RAM, 1 Pentium 4 CPU @ 3.06GHZ and 2 WD Hard Drives (80GB) configured for RAID 0. (There is also an option in the BIOS for what OS type and that is set to Linux.) If anyone has any idea what is going on, it would be helpful. Edit Typing "text" doesn't change a thing. Still stuck at the blinking cursor. I looked it up and it's really the same thing as typing "linux text", which as stated in the first part of my question, I've already done.

  Read the article

• Triple-monitor set-up (2 unique, 1 cloned): Can a VGA splitter be used on one output of a dual-head

  - by stakx

  Background: I'm currently researching hardware components for some kind of information terminal we're building. This application of ours makes use of three output screens: (1) A touch screen where all user input is made; (2) A regular LCD monitor where the requested information is being displayed; and (3) A projector which displays exactly the same signal as screen (2) does. (All screens will run at the same resolution of 1024x768 btw.) Now I figured that using a dual-head video card would be sufficient, let's say a Matrox P690 low-profile PCI card. This would involve having a Y cable connected to the graphics card itself, then two DVI-to-VGA adapters at each end of the Y cable, and then having a VGA splitter on one of the VGA outputs. The following shows the setup in question: 0--1---------2-> VGA (DSUB-15) \ \ ----2-3---------> VGA (DSUB-15) \ \ -----------------> VGA (DSUB-15) 0: graphics card (LFH60 jack) 1: LFH60 to DVI-I dual monitor Y cable 2: DVI-to-VGA adapters 3: VGA splitter cable Question(s): Will this work? I'm particularly concerned about the following points: Can a low-profile PCI video card output a signal which is strong enough for three monitors (even if it's a dual-head card)? Does the combination of so many adapters and splitter cables work? (The LFH-to-DVI cable comes with the video card) Will the VGA splitter cable degrade the signal on the output screen & projector significantly? (If so, would a USB-powered splitter cable remedy this problem?) I can't possibly expect anyone to answer all those questions, but any input is appreciated.

  Read the article

• Find out when a system went down?

  - by Clinton Blackmore

  I have a Mac OS X 10.5 server, with a RAID set in it, that went down due to a power outage on Thursday, and the machine is not happily booting right now*. It is possible to find out when the machine went down, while not booted off the internal drive? (I'm booted off an external drive, waiting for the RAID sets to initialize.) Normally, I'd run last. The man page doesn't indicate that I can run it against a different startup volume. It looks possible to parse /var/log/utmpx, but I don't think it'd be worthwhile to try to do that from scratch for this one-off problem. * I'm still trying to figure out why it isn't happy, and may ask a follow-up question. Right now I can see that UserNotificationCenter crashed repeatedly early Thursday morning, and that securityd, mdworker, and ARDAgent crash shortly after startup [I think -- I want to verify when the box went up and down]. The login window does not come up right (I think it is crashing or not able to cope with a dead securityd). The box is supposed to be set to go down when the UPS tells it power is out; at the moment, I'm wondering if it went down, and turned back on multiple times! I sure hope not.

  Read the article

• Cisco Access switch is dropping large amount of end points

  - by user135458

  This afternoon, with no changes to the network, a switch suddenly started dropping off lots of connections. These connections would come back up a few minutes later, then another area connected to the switch would drop off. This is an older 4006 chassis switch which could in and of itself be a problem but I'm looking to see what else you all would look for in trying to find a root cause. Switch is connected via ports 1/1 and 1/2 in an etherchannel to a VSS core 1/1/42 and 2/1/42. Both sides are up and working however the CPU on the switch will spike up to 99% and that's when CRC errors start to hit the VSS core on one of those interfaces and end points start dropping off. We tried new transceivers and SFP's on each side of the link, same result. When we tried swapping the fiber patch cables on the access switch the CRC errors did not follow the fiber cables they stayed with port 1/2 on the access switch. So port 1/2 on the supervisor module looks like the culprit. We actually tried to create a new member of the ethernet channel by taking a fiber media converter to cat5 and make that a member of the port-channel but when we plugged it in you couldn't even reach the switch. I'm guessing that's unrelated and a problem with the media converter. As of right now we have left it in a state of only one fiber cable running to one side of the VSS core (1/1 Access Switch -- 2/1/42). I've sent some info into TAC and they are looking into the situation but does anyone else have any commands I could run or some troubleshooting I could look into in the meantime?

  Read the article

• Dell PowerEdge 860 won't boot but gets power

  - by fierflash

  I have a Dell PowerEdge 860. Got an 2008 R2 running on it. Here is the scenario I'm currently in: I can boot it up and work as usuall. But when I restart it, it just shuts down, doesn't reboot, and it won't boot up again. Then it stays in this "mode", On/off button blinking green(standby mode?) and System Indicator LED blinking amber. If I try to press the On/Off button on the frontpanel it won't boot. It's like you can hear the fan from the PSU running but nothing else is trying to boot. If I unplug the powercable and then put it back in again it's the same, the extremley noisy fans won't start and it's just sitting there. If I let it "rest" for like 1 to 24 hours while the powercable is unplugged and I plug it in again, it boots directly, without me having to push the On/Off button. What I have tried: Run diagnostics(not the one in POST phase) and everything is fine Booting without any cables except the powercable Boot without memory installed Boot without the raidcable plugged in Cleared NVRAM Reseated all the components and cables Googling like a freak for any possible solution Tried Dell Support but I don't have any warranty left so they can't help me unless i pay some ridiculous amount of money I suppos Do anyone have some experience with the same issue? Do I need to replace something or is there any other way to determine the problem? Any help will be greatly appreciated.

  Read the article

• Can I make my PC backup and then sleep on demand with WHS?

  - by Simon

  I really hate the way that WHS backs up at a particular time in the morning. First of all I don't EVER want my computer turning on when I am not there. EVER. I have a Core-i7 laptop which literally could burn the house down quite easily if it were to turn on in a bag. I also don't ever want my PC to sleep unless I tell it to. I don't have hibernation or sleep enabled and this is the only way that WHS will sleep after a backup is complete. I know that Windows 7 has the ability to disable waking up when on battery power but it doesn't seem to work on my laptop. These are the possibilities (with wake timers left as default): 'Wake this computer for backup' ON - it turns on in my bag if i forget to turn it off - and stays on when the backup is complete. 'Wake this computer for backup' OFF - it backs up in the morning, but I need to leave the machine on all night. I say 'Backup Now' and then it backs up immediately. I can turn it off when its done if I'm still awake, but then that backup appears as 'locked' in the console and not 'automatically managed'. What I'd really like to do is : Click 'Backup and Sleep' and then go to bed. It will backup immediately and then sleep the PC. This backup must be 'automatically managed' and not appear as a 'locked backup' in my console Show me a confirmation that everything was backed up successfully (or not) when I turn it on. Is there any way to achieve this?

  Read the article

• Radeon 6950 - Garbling of text and graphics in certain Windows only

  - by Greg

  This morning I noticed the text in Gmail (in Firefox 4) looked a little funny (kind of thin, maybe some color fringing). I went to work and thought it might be some ClearType issue or something with the way Direct way that FF4 draws to the screen. When I came back from work (I left the computer on), the problem was much worse - way beyond ClearType nit-picking. The text was barely readable. I opened Chrome and there was no such problem. It seems like only Windows that use hardware acceleration are garbled, and ones that use GDI are not. But, I fired up Dragon Age and didn't notice any problems (I only really looked at the main menu though). Here is a link to a screen shot that illustrates the problem. Notice how the Windows Live Mesh window is completely unreadable, the text in Firefox 4 (left) is pretty bad, while Chrome, the Windows Control Panel, and the task bar are perfectly fine. The fact that the problem shows up in screen shots and that it only happens in certain Windows makes me confident that the problem cannot be with the monitor or DVI cable. I am using the AMD Radeon drivers from 4/27/11. The card I have (MSI Frozr II) came with a slight overclock (810Mhz) out of the box, but it looks like when I'm on the Windows desktop it's not running at full clock (CCC reports 450Mhz). Still, I underclocked it to the stock reference clock (800Mhz) and it made no difference. The idle temperature according to Afterburner is 42-44 Celsius, which seems a tad high but not enough to cause a problem - it's cold to the touch if I open up the machine. What the heck could be causing this? The problem varies in intensity. As we speak I'm in Firefox and things look better than they did earlier - it'll probably get worse again soon. Radeon 6950 (MSI Frozr II), Seasonic X 560, Core i5 2500K at stock clockspeeds, 16GB RAM, Asus P8P67 M Pro

  Read the article

• Radeon 6950 - Garbling of text and graphics in certain Windows only

  - by Greg

  This morning I noticed the text in Gmail (in Firefox 4) looked a little funny (kind of thin, maybe some color fringing). I went to work and thought it might be some ClearType issue or something with the way Direct way that FF4 draws to the screen. When I came back from work (I left the computer on), the problem was much worse - way beyond ClearType nit-picking. The text was barely readable. I opened Chrome and there was no such problem. It seems like only Windows that use hardware acceleration are garbled, and ones that use GDI are not. But, I fired up Dragon Age and didn't notice any problems (I only really looked at the main menu though). Here is a link to a screen shot that illustrates the problem. Notice how the Windows Live Mesh window is completely unreadable, the text in Firefox 4 (left) is pretty bad, while Chrome, the Windows Control Panel, and the task bar are perfectly fine. The fact that the problem shows up in screen shots and that it only happens in certain Windows makes me confident that the problem cannot be with the monitor or DVI cable. I am using the AMD Radeon drivers from 4/27/11. The card I have (MSI Frozr II) came with a slight overclock (810Mhz) out of the box, but it looks like when I'm on the Windows desktop it's not running at full clock (CCC reports 450Mhz). Still, I underclocked it to the stock reference clock (800Mhz) and it made no difference. The idle temperature according to Afterburner is 42-44 Celsius, which seems a tad high but not enough to cause a problem - it's cold to the touch if I open up the machine. What the heck could be causing this? The problem varies in intensity. As we speak I'm in Firefox and things look better than they did earlier - it'll probably get worse again soon. Radeon 6950 (MSI Frozr II), Seasonic X 560, Core i5 2500K at stock clockspeeds, 16GB RAM, Asus P8P67 M Pro

  Read the article

• Remote Desktop Zooming

  - by codeulike

  Using Remote Desktop from a device with a hi-res screen (say, a Surface Pro) is decidedly tricky - as everything displays 1:1 scale and so looks tiny. If the machine you are remoting into runs Server 2008 R2 or later, you can change the dpi zooming setting (see here). But for older hosts, that doesn't work. Using normal Remote Desktop, you can connect with a lower resolution, say 1280x768, and turn on smart-sizing. However smart-sizing can scale down (to display a huge desktop in a small area) but does not seem to scale up (to display a small desktop in a big area). Using the Windows 8 Remote Desktop App, you can zoom - but you cannot set the default resolution of the host. What I want is a lower resolution in the host, scaled up to fit my screen. So both of those are close to what I want, but dont quite work. So question is: Does the Remote Desktop App allow screen resolution to be set somehow? Is there some other Remote Desktop client that can handle zooming better?

  Read the article

• How can I set up a touchscreen as the non-primary monitor in a dual monitor situation?

  - by bazzjedi

  I have been looking for information about using a second monitor, and thought of using a touchscreen. Will a touchscreen monitor work in a dual setup if it is not the main monitor? I haven't found any information on this; I've only found information about the touchscreen being the main monitor. That is, except at this SU question (snippet below): If you mean do the touch screen features still work on the other machine, the answer is yes. Past that, you can even see some of the touch screen features on a non touch screen monitor (just not the multi touch features!) For example, on the taskbar, click (without releasing) on any icon and then drag the mouse up, and you will see that it does the same as using your finger and dragging up. I have a HP 2510 for the main monitor. I'm thinking of adding a HP 2310ti (the touchscreen) as the secondary. My graphics card is a geforce gtx 295. I'm running Windows 7 Professional.

  Read the article

• raid 0 data recovery?

  - by Fred

  HI All, I have two identical seagate 7200.9 500Gb drives confiured as a RAID 0 spanned disk in windows. One of the drives has lost power and wont spin up at all. I know this normally means death for the data on both drives but i have a cunning plan.. DISK 1 - NO POWER RAID 0 DISK DISK 2 - FULLY FUNCTIONAL RAID 0 DISK DISK 3 - FULLY FUNCTIONAL SPARE DISK Copy the working drive (disk 2) data to a third 500GB DISK (disk 3), remove the logic board from the working disk (disk 2) and replace it with the non working logic board on the broken drive (disk 1) , then hopefully recreate the RAID 0 with disk 1 and disk 3, just long enough to get the data off it. Hope this makes sense, here are my questions: Windows disk manager atm recognises disk 2 but wont let me access it in anyway, therefore copying the data off it (or getting a disk image) cant be done in windows. Does anyone know of any software (in linux or self booting) that would allow me to access this disk? Anyone know of any software that will recreate the spanned drive off two disk images Am i missing any key information that means i definitely shouldn't even bother starting this, i know its a long shot anyway but its worth a try unless i definitely cant do it. The irritating thing is that i am sure its a logic board failure on disk 1 as it simply wont power up at all, suddenly no signs of life, so i am sure the data is intact! Any help would be really appreciated! Thanks

  Read the article

• Connect to Nonencrypted Wireless Network Using Ubuntu Commands

  - by Tim

  I failed to connect to an open i.e. nonencrypted wireless network using Ubuntu command lines. Here is what I did: $ sudo /etc/init.d/NetworkManager stop * Stopping network connection manager NetworkManager [ OK ] $ sudo /sbin/ifconfig wlan0 up $ sudo iwconfig wlan0 essid "Cavalier High-Speed 866-4-CAVTEL" $ sudo dhclient wlan0 There is already a pid file /var/run/dhclient.pid with pid 10812 killed old client process, removed PID file Internet Systems Consortium DHCP Client V3.1.1 Copyright 2004-2008 Internet Systems Consortium. All rights reserved. For info, please visit http://www.isc.org/sw/dhcp/ wmaster0: unknown hardware address type 801 wmaster0: unknown hardware address type 801 Listening on LPF/wlan0/00:0e:9b:cd:4e:18 Sending on LPF/wlan0/00:0e:9b:cd:4e:18 Sending on Socket/fallback DHCPREQUEST of 192.168.1.67 on wlan0 to 255.255.255.255 port 67 DHCPREQUEST of 192.168.1.67 on wlan0 to 255.255.255.255 port 67 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 7 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 7 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 8 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 12 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 21 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 6 No DHCPOFFERS received. Trying recorded lease 192.168.1.67 PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data. --- 192.168.1.1 ping statistics --- 1 packets transmitted, 0 received, +1 errors, 100% packet loss, time 0ms Trying recorded lease 192.168.1.45 PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data. --- 192.168.1.1 ping statistics --- 1 packets transmitted, 0 received, +1 errors, 100% packet loss, time 0ms No working leases in persistent database - sleeping. $ sudo /sbin/iwconfig wlan0 wlan0 IEEE 802.11bg Mode:Managed Frequency:2.422 GHz Access Point: Not-Associated Tx-Power=27 dBm Retry min limit:7 RTS thr:off Fragment thr=2352 B Encryption key:off Power Management:off Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 I was wondering what the problem is and how I can do it right? Thanks and regards!

  Read the article

• Connecting a laptop to a TV via HDMI

  - by Madmartigan

  I just bought a new Dell XPS17 laptop (Win7) that only has HDMI output. My last 2 laptops had VGA, which I used to connect to my Sony Bravia 32" TV with no issues, but with the HDMI it's been quite a headache. Drivers for display adapters have been updated to the latest versions: Intel(R) HD Graphics Family NVIDIA GeForce GT 550M I went to a store and plugged in to 4 different TVs from different manufacturers. A sales rep and I spent about 30 minutes being baffled by the results (which are the same as my current TV): Extreme buggy behavior in the Nvidia and Windows display/resolution control panel Can not extend or duplicate displays, can only select one Third and fourth output devices "randomly" detected by the Windows control panel Could not get the screen to fit the output (edges cut off on all sides by about a half inch) Resolution and colors less than perfect. Artifacts around text. Display "randomly" cuts out Defaults to TV output only when plugged in Can not change resolution on either device when connected No audio from the TV Plugged in to 3 monitors from different manufacturers: Defaults to duplicated displays when plugged in Everything works perfectly So far, four people have gone through all the settings in the latop with no luck. I had similar, but not exactly matching results with a different laptop. I'm using the Sony Bravia currently at home, but in order to get it to work I have to turn on the laptop, wait until the display shows up on it, close the lid, then cycle through each output channel on the TV until I come back around to the HDMI port again, but still I have the symptoms described above. However: Once in a while, it just works. Sometimes, seemingly randomly, the output fits the screen perfectly. Sometimes the audio comes through the speakers too, but not always. Usually my screen saver "Mystify" will come up with a message that it cannot be displayed due to a limitation of the video card, but then sometimes it works fine. These 3 things seem to be independent of each other and don't always happen together. So, is there any way to get the laptop to output correctly to a TV, or is it just not meant to be?

  Read the article

• Windows 8 keeps signing out

  - by bill weaver

  Ran into a strange problem with Windows 8 Pro. Last night i installed Windows 8 Pro as an upgrade on a Sony Vaio laptop that had Windows 7 Pro on it. The install seemed to go okay. Then once installed, live tiles seem to work, native/Metro apps will start okay, but pretty soon after going into an app or settings, the screen flashes a few times and we're back to the lock screen. Signing in appears to do a full login. I've tried this with a local account and with a live.com account. This is someone else's laptop, so we decided to let it breathe, in case the install was still settling in. Well, they say today it's doing the same thing. Open the music app, and within a minute it's back to signon/lock screen. However, they can go to the actual Desktop and run Zune to play music, and it seems happy. In the past, i've installed retail Windows 8 Pro clean on a homebrew system, as an upgrade on a Dell laptop with a zillion apps and drivers, neither with any problems. Also, i've had the consumer preview and release candidate installed as well, no problems. Any ideas on what's going on here?

  Read the article

• Windows 8.1 in a VMWare Workstation 10 guest's mouse is missing, but only sometimes

  - by Rob Perkins

  I have VMWare Workstation 10 running on a Windows 7 machine, hosting a k guest OS. Before upgrading to WS 10 I was using version 9, and the Win8 guest OS ran without difficulty or error conditions. Since upgrading and installing the most current VMWare Tools inside the guest after upgrading to version 10, there are circumstances where the mouse pointer is not visible; the mouse position appears stuck at a screen location which is not the center of the virtualized display; and mouse click and scrolling events still get processed. Once this begins happening I have to reboot the host machine to get it to stop. (VMWare Tools 9.6.1 build-1378637 is what the WS 10 software installed) The problem seems to correlate with whether the mouse is captured during Win 8.1's bootup process, before control is passed to the login screen. If I explicitly click the mouse into the guest OS and move it slowly around while the system is booting, then I see the mouse after clicking to lift the first screen and expose the password prompt, and there is never a problem within the guest. If I don't do this during bootup, there is no mouse pointer, with the symptoms listed above. I have tried removing and reinstalling VMWare tools, and the other steps published for "mouse problems" from VMWare's chaotic troubleshooting database. The problem persists. Is there a setting in the virtual machine's configuration which could prevent this behavior?

  Read the article

• Power issues Foxconn Barebones kit

  - by alpha1

  I have a Foxconn R20D2 bought about a year and a half ago. It ran fine for a while and then around last summer it started having power issues. I chalked it up to changes in electric current due to the overwhelmed grid when people turn on their AC units, but this problem has stayed for all year, shutting off randomly, shutting off when i turn on a vacuum and similar problems. Now that its summer again, the box basically sits there all day cycling itself, and now has gotten to the point it tried to boot and after 3 seconds, fails, shuts off and tried again. I know its power related, it runs opensuse linux and there are never any shutdown logs or anything of that sort. As the weather got hotter i noticed it happening more and more, and it most often happened in the morning, i presume as people woke up and turn on the AC. The power supply is a Chennel well technology co LTD model DSL-150. 150W max output. Its an intel atom dual core, with 2 sata drives, no CD/floppy etc, recently upgrades from 2 to 4gb of ram. It runs at 104 degrees Fahrenheit all the time almost. Any way i can test the power supply or anything else to try to fix it? Im a software guy, not hardware so im at a complete loss here, thanks for all assistance you can provide! EDIT: The switch on the back that says 230 or 115 is set to 230. If im in the USA, could that be causing the problems?

  Read the article

• Setting up xpra for client use in OS X

  - by Jonathan

  I've been trying to get xpra to run on OS X for the last few days to connect to my Ubuntu server. Note that there's a GUI for it called shifter, but that (at least on OS X) is still far too buggy. For those who don't know what xpra is, if you know what screen is, it's like screen for GUI X Windows apps tunneled over ssh. You can render a remote X app locally so it's faster than sending a series of compresses screen shots (like VNC), but with xpra you can disconnect and reconnect on different computers. To get the basic functionality you can just type "ssh -X server.location" and any GUI app you open from the command line will open locally. I've been able to get xpra to build by doing the following: Download pari-all-0.0.6.tar.gz from the xpra site listed under upstream and untar it. Issue the following Mac Ports command (Dependencies thanks to RogBlog): sudo port install python25 python26 py26-pyrex py26-gtk xorg-libXtst py25-gobject py25-gtk py25-nose py26-nose xorg-libXdamage xorg-libXcomposite xorg-libXtst xorg-libXfixes In the upstream list of v0.0.06 patches (NOT 0.0.8pre!) on the xpra site listed above, download mswindows-conditional-pyrex.patch. Open the patch with your favorite text editor and change the single occurrence of "win" in it to "darwin". Apply the patch to setup.py. Run do-build in the command line. Now where I'm stumped: how do I run xpra? The build produces a sub directory called install/bin in which xpra is located, but when I try to run it I get the following error: Traceback (most recent call last): File "./xpra", line 4, in import xpra.scripts.main ImportError: No module named xpra.scripts.main There is a file called main.py under xpra/scripts, but I don't know any python and I'm not sure if this is what it's looking for, and what to do with it even if it is. My goal is to set up xpra so I can install it into /usr/bin (or some other common path for executables) and execute it whenever I please. What do I do next?

  Read the article

• Ubuntu 10.10 - PC shutdown before boot shortly after BIOS loads

  - by clem

  Since installing Ubuntu 10.10 from Karmic I've started getting problems with starting up the PC. I've done a complete wipe (Boot and Nuke) of the hard drive and reinstalled Ubuntu 10.10 but the problem still occurs. There is no dual boot on the PC, just Ubuntu. Here is the problem: Each morning, when I turn the PC on from being off overnight, the PC starts up and loads the BIOS. I get the following message Verifying DMI Pool Data... K8 NPT Data Change...Update New Data to DMI!....... Then poof the computer shuts off. However, after switching the computer back on around 6 or 7 times after it's turned itself off, it will eventually boot up without any problem. Also, once up and running for a while, I can shutdown and restart the PC first time, without any issues. I have also noticed a problem with the USB mouse being recognised and once I finally get the computer booted up, I need to unplug and then plug the mouse back in to get it working. I've opened the PC up and checked the connections (cables, cards and memory) and it all seems fine. The main issue with troubleshooting this problem is I cannot test any suggestions or fixes until the next morning because once the computer is up and running it will remain so! I do not leave the computer on overnight to save energy. So.. Is this a hardware / boot software issue? This is a very odd problem and I have googled to no avail. Any suggestions?

  Read the article

• Safemode Startup Issues on Vista 64 Bit

  - by GnrlBzik

  Before i ask the question, let me point out that this is not a hardware issue. I have a clean install of vista on another hd that runs on same hardware, i am pretty sure its a corruption of a drive or a file, i presume it might be video driver. When windows wont start via normal boot i just get black screen after initial load up of os, so i boot into savemode, I end up having black screen with a mouse pointer visible, after initial load of os. The shut down button is responsive. Of course, I can install clean copy of os, and prior to that can retrieve all other files that i need by accessing hd itself, i can restore my pc from my external back up as well. Although i have all these options, i was wondering if there anything else i can do that can help me fix this issue. In save mode, it looks like I am capable of logging in after initial load of os, even though i cant see the process it self, i do see the mouse pointer. By visual memory i navigated to password field, and entered my password, hit enter, I get the loading mouse pointer, nothing really changes, same black screen and mouse pointer, but when i tried to access task manager for a second i got a safemode watermark at all four corners. Any help would be appriciated. Thank you in advance.

  Read the article

• Roaming Profiles & Redirected Folders - storage consumption? offline files and caching?

  - by Ben Swinburne

  I understand the concepts of both roaming profiles and folder redirection and have used both separately before. I am about to set up a network from scratch and would ideally like to use both for the following reasons primarily Roaming profiles allow users to log on to any machine and have their profile Redirected profiles allow users to have their My Documents and Desktop etc backed up without the need to log off at the end of the day. The servers can run their backups overnight and there are no missing files due to the user not logging off. Redirected profiles largely alleviate the slow log in times caused by large profiles. My question is if some of the folders are redirected and therefore not part of the roaming profile what happens on machines which truly roam (i.e. laptops)? If there's offline files or a cache does this mean that the problem whereby a user has to log off comes back? By having them both enabled, is there any duplication i.e. if I have a users$ share and a profiles$ share would I have Desktop twice for example?

  Read the article

• Computer Won't Boot Properly, unless in safe mode?

  - by Mr_CryptoPrime

  I bought a computer today and booted it up, but when I did I only got a blank screen. I checked to make sure it wasn't the monitor by connecting it to my old computer...it worked. I then tried connecting my monitor to both DVI ports and found that the bottom one did work. However, now it just boots up and says "loading windows" and then when the login screen is suppose to come up the screen just goes blank and monitor says "no input, check cord" (or something like that). I tried reinstalling windows and then I was able to log on normally. I used the CD's and reinstalled all the drivers, then rebooted...now I am stuck right back where I started. I tried taking out the RAM and inserting into different slots, that didn't fix anything. I was able to boot up into windows using safe-mode. I suspected that my ATI Radeon 6950 was the issue and downloaded the drivers, but I can't install them on safe-mode. Someone said to install C++ distr. and I tried doing that to fix driver installation problem of "failed to load detection driver" but it wouldn't let me do that either. Please someone help me, I don't want to have to deal with the evil redtape of sending it back to get a replacement! My computer: -Content--text-_-"http://www.newegg.com/Product/Product.aspx?Item=N82E16883229236&nm_mc=TEMC-RMA-Approvel&cm_mmc=TEMC-RMA-Approvel--Content--text-_- Driver detection problem: http://www.hardwareheaven.com/hardwareheaven-tools-discussion/174912-failed-load-detection-driver-installation-error.html Driver download page: http://sites.amd.com/us/game/downloads/Pages/radeon_win7-64.aspx#1 I am using windows 7. Thanks again.

  Read the article

• Windows 7 Startup fails after installation

  - by Nadav S.

  I have installed Windows 7 Ultimate a week ago. Yesterday I've noticed that the SP1 update is available. After installation of SP1 the computer failed to startup, and had shown a black screen. I couldn't even go to safe mode and F8 didn't help. After some fixing attempts including system restore, startup repair, bootmgr & BCD rebuilding from CMD, I have decided to reinstall Windows (after all, it's only a week old) After the successful installation, I have decided to first install all available updates before I continue. So after the updates download & installation, the computer rebooted. And now I didn't see the black screen again - but in the "Starting Windows..." screen the logo didn't appear and the system didn't startup. Here I could go to safe mode selection window, but it didn't work either ("Loading Windows Files" but nothing). I've also tried: I thought that the CD was corrupted, so I've used a fresh new disk of Windows, tried x86 & x64 versions, the same symptoms, no change. Resetted the BIOS to default, no change. Memory diagnostic HDD diagnostic Restarted Windows WITHOUT INSTALLING UPDATES, but it had the same symptom, so maybe Windows Update is not the case?! I've tried installing it so many times - that I am simply stuck - I can't "reinstall Windows, because it is corrupted...". Maybe the HDD is corrupted? I've also checked it and didn't find a problem.

  Read the article

• nginx - proxy_pass is working - Apache isn't doing what it should...

  - by matthewsteiner

  So, I've got this in my nginx.conf: location ~* ^.+.(jpg|jpeg|gif|png|ico|css|zip|tgz|gz|rar|bz2|doc|xls|exe|pdf|ppt|txt|tar|mid|midi|wav|bmp|rtf|js)$ { root /var/www/vhosts/example.com/public/; access_log off; expires 30d; } location / { proxy_pass http://127.0.0.1:8080/; proxy_redirect off; proxy_set_header Host $host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; } So anything that is a "static file" that exists will just be done with nginx. Otherwise, it should pass it off to Apache. Right now, static files are working correctly. However, if something is passed to apache and it's example.com or subdomain.example.com, apache just spits out the "Apache 2 Test Page" that you get if there's nothing there. Apache worked fine before, so I'm guessing it has to do with the way nginx is "asking". I'm not sure though. Any ideas?

  Read the article

• Nginx, as reverse proxy, could not proxy_pass to a domain pointing to the local JBOSS

  - by larryzhao

  My environment is Ubuntu 12.04, Nginx 1.20, and Torquebox 2.0.3 which is actually JBoss AS 7. I have two app deployed on Torquebox, it listens to 8080 and have different hostnames, app1.mydomain.com and app2.mydomain.com. I added 127.0.0.1 app1.mydomain.com and 127.0.0.1 app2.mydomain.com in /etc/hosts then I curl app1.mydomain.com:8080 and curl app2.mydomain.com:8080 both have correct return. Then I go to my nginx. I would like nginx to pass the visit to www.app1.com to app1.mydomain.com:8080, so I have the following configuration: # primary server - proxypass to torquebox server { listen 80; server_name www.app1.com; access_log off; error_log off; # proxy to Torquebox location / { proxy_pass http://app1.mydomain:8080/; proxy_redirect off; proxy_set_header Host $host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_max_temp_file_size 0; client_max_body_size 10m; client_body_buffer_size 128k; proxy_connect_timeout 90; proxy_send_timeout 90; proxy_read_timeout 90; proxy_buffer_size 4k; proxy_buffers 4 32k; proxy_busy_buffers_size 64k; proxy_temp_file_write_size 64k; } } But it doesn't work. curl www.app1.com returns nothing. And if I visit www.app1.com in Safari, the http return code is 404. I don't know why, need help.

  Read the article

< Previous Page | 257 258 259 260 261 262 263 264 265 266 267 268  | Next Page >