Search Results

Search found 41511 results on 1661 pages for 'via point'.

Page 261/1661 | < Previous Page | 257 258 259 260 261 262 263 264 265 266 267 268  | Next Page >

  • Ubuntu and racadm

    - by lmqcn
    I recently purchased a used poweredge 1850 server and it came with a DRAC card. After wiping the HDD and installing ubuntu server 12.04.3 LTS amd64 on it, I am now trying to gain access to the DRAC which I believe is version 4. I have properly configured the DRAC to use it's own IP on my LAN and when I point my browser to the IP address, I am greeted with the DRAC login page (it has the dell logo and everything). However, after trying the credentials of root/calvin, I was denied access. So I think that the previous owners had set their own password. After doing some reading, it appears that I can reset the credentials to the default using racadm config -g cfgUserAdmin -o cfgUserAdminPassword -i 1 newpassword but upon entering the command, I get this error: bash: /usr/sbin/racadm: No such file or directory This holds true even if I run sudo su prior to running the racadm command. If, however, I run sudo racadm config -g cfgUserAdmin -o cfgUserAdminPassword -i 1 newpassword there are no errors. Yet, when I try to log into the DRAC via the web interface using the credentials of root/newpassword I am still not granted access. I installed the dell utilities via the guide at https://wiki.ubuntu.com/HardwareSupportMachinesServersDellNotes. I first tried to install the 64 bit version that is on the dell repositories, but after that was unsuccessful, I just followed the guide verbatim. No errors were produced in either case. I even followed the information at the bottom of the guide by executing sudo pppd /dev/ttyS1 1382400 crtscts noipdefault noauth lock persist connect 'chat -v "" CLIENT CLIENTSERVER "\\c"' but obviously, replacing the /dev/ttyS1 with the correct information for my system. ls -l /usr/sbin/ | grep racadm yields -rwxr-xr-x 1 root root 87930 Sep 16 04:03 racadm I have tried these credentials after each attempt of changing the password: root/calvin root/newpassword admin/calvin admin/newpassword All have been unsuccessful. What is the next course of action that I should take?

    Read the article

  • Request Tracker 4.x on Ubuntu 12.04

    - by rihatum
    I have a Ubuntu 12.04 server installed on my machine. I am trying to install request-tracker4. Here's what I have done so far : a) Installed request-tracker via "sudo apt-get install request-tracker4" b) I then tried configuring RT_SiteConfig.pm in /etc/request-tracker4 but then ran into problems in populating the MySQL database. c) I then did sudo dpkg-reconfigure request-tracker4 d) It solved my problems of not being able to populate / setup mysql etc. e) Now, I am trying to setup rt under www.mydomain.com/rt I have read various how-to's and bestpractical's own guides but I am not very much a expert in Apache configurations so stuck. My Current Ubuntu 12.04 server setup: Apache2, Fastcgi installed (checked in /etc/apache2/mods-enabled Web Server document root is default /var/www/ Web user www-data Question is : 1 ) Where and What shall I put in Apache configuration to start using RT via the web-interface ? I have seen two files in /etc/request-tracker4/ apache2-fastcgi.conf and apache2-fcgid.conf I even tried making a ln -s apache2-fastcgi.conf /etc/apache2/conf.d but when I tried opening that file in root while in the conf.d directory it said too many levels. Any request tracker experts on ubuntu ?:-) Your help will be very useful and appreciated Thanks Please let me know if you need further info !

    Read the article

  • how to customize rocket dock

    - by user23950
    how to customize rocket dock. So that when I point to an application or folder that is docked on rocket dock. Other Options will appear. For example, folders that is within the folder that is dragged on rocket dock. Or if you point to an application launcher that is in rocket dock. Rocket dock will show the applications that has shortcuts on that application launcher. simplified: A rocket dock which is the same as the file explorer. Wherein there is a root folder that is being expanded and expanded

    Read the article

  • CodePlex Daily Summary for Wednesday, December 22, 2010

    CodePlex Daily Summary for Wednesday, December 22, 2010Popular ReleasesTibiaPinger: TibiaPinger v1.0: TibiaPinger v1.0Media Companion: Media Companion 3.400: Extract the entire archive to a folder which has user access rights, eg desktop, documents etc. A manual is included to get you startedPackage that minifies and combines JavaScript and CSS files: Release 1.1: Bug fixes. The package now correctly handles inlined images and image urls in CSS files surrounded by quotes. CombineAndMinify can now be used in conjunction with Microsoft's Sprite and Image Optimization Framework. That framework combines several small images into one, reducing overall load times.Multicore Task Framework: MTF 1.0.1: Release 1.0.1 of Multicore Task Framework.SQL Monitor - tracking sql server activities: SQL Monitor 3.0 alpha 7: 1. added script save/load in user query window 2. fixed problem with connection dialog when choosing windows auth but still ask for user name 3. auto open user table when double click one table node 4. improved alert message, added log only methodOpen NFe: Open NFe 2.0 (Beta): Última versão antes da versão final a ser lançada nos próximos dias.EnhSim: EnhSim 2.2.6 ALPHA: 2.2.6 ALPHAThis release supports WoW patch 4.03a at level 85 To use this release, you must have the Microsoft Visual C++ 2010 Redistributable Package installed. This can be downloaded from http://www.microsoft.com/downloads/en/details.aspx?FamilyID=A7B7A05E-6DE6-4D3A-A423-37BF0912DB84 To use the GUI you must have the .NET 4.0 Framework installed. This can be downloaded from http://www.microsoft.com/downloads/en/details.aspx?FamilyID=9cfb2d51-5ff4-4491-b0e5-b386f32c0992 - Fixing up some r...LINQ to Twitter: LINQ to Twitter Beta v2.0.18: Silverlight, OAuth, 100% Twitter API coverage, streaming, extensibility via Raw Queries, and added documentation. Bug fixes.ASP.NET MVC Project Awesome (jQuery Ajax helpers): 1.4.3: Helpers (controls) that you can use to build highly responsive and interactive Ajax-enabled Web applications. These helpers include Autocomplete, AjaxDropdown, Lookup, Confirm Dialog, Popup Form, Popup and Pager new stuff: Improvements for confirm, popup, popup form RenderView controller extension the user experience for crud in live demo has been substantially improved + added search all the features are shown in the live demoGanttPlanner: GanttPlanner V1.0: GanttPlanner V1.0 include GanttPlanner.dll and also a Demo application.N2 CMS: 2.1 release candidate 3: * Web platform installer support available N2 is a lightweight CMS framework for ASP.NET. It helps you build great web sites that anyone can update. Major Changes Support for auto-implemented properties ({get;set;}, based on contribution by And Poulsen) A bunch of bugs were fixed File manager improvements (multiple file upload, resize images to fit) New image gallery Infinite scroll paging on news Content templates First time with N2? Try the demo site Download one of the templ...TweetSharp: TweetSharp v2.0.0.0 - Preview 6: Documentation for this release may be found at http://tweetsharp.codeplex.com/wikipage?title=UserGuide&referringTitle=Documentation. Note: This code is currently preview quality. Preview 6 ChangesMaintenance release with user reported fixes Preview 5 ChangesMaintenance release with user reported fixes Preview 4 ChangesReintroduced fluent interface support via satellite assembly Added entities support, entity segmentation, and ITweetable/ITweeter interfaces for client development Numer...Team Foundation Server Administration Tool: 2.1: TFS Administration Tool 2.1, is the first version of the TFS Administration Tool which is built on top of the Team Foundation Server 2010 object model. TFS Administration Tool 2.1 can be installed on machines that are running either Team Explorer 2010, or Team Foundation Server 2010.SubtitleTools: SubtitleTools 1.3: - Added .srt FileAssociation & Win7 ShowRecentCategory feature. - Applied UnifiedYeKe to fix Persian search problems. - Reduced file size of Persian subtitles for uploading @OSDB.Facebook C# SDK: 4.1.0: - Lots of bug fixes - Removed Dynamic Runtime Language dependencies from non-dynamic platforms. - Samples included in release for ASP.NET, MVC, Silverlight, Windows Phone 7, WPF, WinForms, and one Visual Basic Sample - Changed internal serialization to use Json.net - BREAKING CHANGE: Canvas Session is no longer support. Use Signed Request instead. Canvas Session has been deprecated by Facebook. - BREAKING CHANGE: Some renames and changes with Authorizer, CanvasAuthorizer, and Authorization ac...NuGet: NuGet 1.0 build 11217.102: Note: this release is slightly newer than RC1, and fixes a couple issues relating to updating packages to newer versions. NuGet is a free, open source developer focused package management system for the .NET platform intent on simplifying the process of incorporating third party libraries into a .NET application during development. This release is a Visual Studio 2010 extension and contains the the Package Manager Console and the Add Package Dialog. This new build targets the newer feed (h...WCF Community Site: WCF Web APIs 10.12.17: Welcome to the second release of WCF Web APIs on codeplex Here is what is new in this release. WCF Support for jQuery - create WCF web services that are easy to consume from JavaScript clients, in particular jQuery. Better support for using JsonValue as dynamic Support for JsonValue change notification events for databinding and other purposes Support for going between JsonValue and CLR types WCF HTTP - create HTTP / REST based web services. This is a minor release which contains fixe...LiveChat Starter Kit: LCSK v1.0: This is a working version of the LCSK for Visual Studio 2010, ASP.NET MVC 3 (using Razor View Engine). this is still provider based (with 1 provider Sql) and this is still using WebService and Windows Forms operator console. The solution is cleaner, with an installer to create tables etc. You can also install it via nuget (Install-Package lcsk) Let me know your feedbackOrchard Project: Orchard 0.9: Orchard Release Notes Build: 0.9.253 Published: 12/16/2010 How to Install OrchardTo install the Orchard tech preview using Web PI, follow these instructions: http://www.orchardproject.net/docs/Installing-Orchard-Using-Web-PI.ashx Web PI will detect your hardware environment and install the application. --OR-- Alternatively, to install the release manually, download the Orchard.Web.0.9.253.zip file. The zip contents are pre-built and ready-to-run. Simply extract the contents of the Orch...DotSpatial: DotSpatial 12-15-2010: This release contains a few minor bug fixes and hopefully the GDAL libraries for the 3.5 x86 build actually built to the correct directory this time.New Projects1102 Puc enigami: noitpircsedaarron: personalALDX Organizer: C# .NET desktop application meant to help a store manager in running the store.Battle.Net Library: This is a collaborate Blizzard Battle.net api. Currently working on fetching data from the Armory.BBSolution: BBSolution cmsBitlyTweeter: A Windows Live Writer plugin designed to hook up to your bit.ly account and automatically send tweets after you publish a blog post with the URL shortened by your account.Chat World: chat privado sin reestricciones de ningun tipo aplicacion cliente servidor cliente que te permite crear tus propias salas y categorias de chat sin ninguna reestriccion desarrollado en Net 4.0 lenguaje c#Creating Databound jQuery plugins for ASP.NET: Using asp.net to create a dynamic webservice to support the jQuery jqGrid control as a databound server control. Developed in C# and Javascript. Designed to remove excessive extra coding to add rows to gridview control. Short time to fully developed control.DriverStore Explorer [RAPR]: DriverStoreExplorer GUI makes it easier to deal with Windows Vista / Windows 7 driver store. Supported operations include enumeration, adding a driver package (stage), adding & installing, deletion, as well as force deletion from the driver store. GCTF: Desafio .NET Realizado na FACISAGonte.Utilities: Gonte.Utilites Provides general utilities such as - Reflection helpers - Validation framworkLincoln Wood: An evolutionary implementation of the next gen Lincoln Wood Community environment using MVC2 and other good stuff.M4N1: M4N1 its a MDA arquitecture that tries to enable Model Development for anyone! Its written an Java and the IDE its an Eclipse RCP application.MasterGuitarReader: guitarmd5util: MD5 checksum util for developersMP3Tunes Windows Locker Player: Connect to your MP3Tunes locker from a win7/vista/xp computer.MVC Installer: The MVC Installer is a small, pluggable assembly that you add to any new ASP.NET MVC 2 project to easily install your database and Membership system with Roles and Users.new1: new1new1new1new1new1O(∩_∩)O: .SharePoint 2007 Add Ons: The goal of this project is to develop a set of add ons for SharePoint 2007.SharePoint Power Pack: The SharePoint Power Pack consists of several features to enhance core functionality and change the user experience of the SharePoint GUI.Silverlight Code Camp Reference Implementation: Silverlight Code Camp Website Australia 2011. Technology: C#, Silverlight, Asp.Net MVC, jQuery Features: CodeCamp Sessions, Location Map, User Voting, Registration (via EventBrite), Down Level Experience, Mobile Browsers friendly CSS Silverlight Sockets Sample: Trivial but complete sample for doing SL sockets. There is an SL project and a console socket server handling 943rd (SL policy) port and 4505th (for arbitrary data communication).SMILE Media Content Creator: A WinForm GUI for generating SMILE Media ContentSocialPad: socialpadSpits: Comment SNS for files: A sns like comment system. can make comments with your very local files StarTrooper: ????,??MSDN Webcast ???,???VB A game, reference MSDN Webcast produced by the language is Visual Basic http://www.msdnwebcast.com.cn/CourseSeries.aspx?id=58Text Data File Manipulator: Manipulate text data files: convert separators, transpose data. For some reason I couldn't find a simple tool for window to transpose my large data files so I wrote this tiny tool. uLogin: uLogin version 1.0.1 provides Member Login functionality for Umbraco-powered Web sites. uLogin version 1.0.1 was developed and tested for Umbraco version 4.5.2 with ASP.net version 4.Windows Media Player GNTP Plugin: WMP-GNTP allows Windows Media Player to tell Growl for Windows when a song has changed, so you'll no longer have to open Windows Media Player to tell when a song has changed. It's developed in C++/ATL.WorldBuilder: This Application will help XNA developers create game maps and easily implement them into their games. This includes both 2D maps and 3D Terrain maps.

    Read the article

  • HTTP downloads slow - FTP of same file very fast - Windows 2003

    - by Paul Hinett
    I am having some issues with download speeds on my site via http, i am averaging around 70kbps downloading a file that is around 70mb. But if i connect to my server via FTP and download the same file on the same computer / connection i am averaging about 300+kbps. I know my server has alot of connections at any one time, probably around 400 connections. My server has a 1gbps connection to the internet so there is plenty of bandwidth available, as proven with the FTP. I have no throttling of any kind enabled in IIS. If interested there is a test file here you can download to check the speed: http://filesd.house-mixes.com/test.zip I am based in the UK and the server is in Washington, USA if that makes any difference. Paul

    Read the article

  • How to practice object oriented programming?

    - by user1620696
    I've always programmed in procedural languages and currently I'm moving towards object orientation. The main problem I've faced is that I can't see a way to practice object orientation in an effective way. I'll explain my point. When I've learned PHP and C it was pretty easy to practice: it was just matter of choosing something and thinking about an algorithm for that thing. In PHP for example, it was matter os sitting down and thinking: "well, just to practice, let me build one application with an administration area where people can add products". This was pretty easy, it was matter of thinking of an algorithm to register some user, to login the user, and to add the products. Combining these with PHP features, it was a good way to practice. Now, in object orientation we have lots of additional things. It's not just a matter of thinking about an algorithm, but analysing requirements deeper, writing use cases, figuring out class diagrams, properties and methods, setting up dependency injection and lots of things. The main point is that in the way I've been learning object orientation it seems that a good design is crucial, while in procedural languages one vague idea was enough. I'm not saying that in procedural languages we can write good software without design, just that for sake of practicing it is feasible, while in object orientation it seems not feasible to go without a good design, even for practicing. This seems to be a problem, because if each time I'm going to practice I need to figure out tons of requirements, use cases and so on, it seems to become not a good way to become better at object orientation, because this requires me to have one whole idea for an app everytime I'm going to practice. Because of that, what's a good way to practice object orientation?

    Read the article

  • Virtual machine on ubuntu

    - by MITHIYA MOIZ
    I have configured virtual machine on ubuntu with the help of below article, https://help.ubuntu.com/9.04/serverguide/C/libvirt.html I managed to finish all the part except the major portion getting virtual host to talk to real network, Which I guess should be done only via bridge interface. Via virtual machine manager I try to choose any interface it gives me interface not bridged When I try to bridge the interceface eth0 as below auto br0 iface br0 inet static address 192.168.0.223 network 192.168.0.0 netmask 255.255.255.0 broadcast 192.168.0.255 gateway 192.168.0.1 bridge_ports eth0 bridge_fd 9 bridge_hello 2 bridge_maxage 12 bridge_stp off I cannot communicate with this interface to network, host server looses all the communication to network. But when I remote bridge interface from /etc/network/interfaces And configure eth0 as below it works fine The primary network interface auto eth0 iface eth0 inet static address 192.168.0.223 netmask 255.255.255.0 network 192.168.0.0 broadcast 192.168.0.255 dns-nameservers 62.215.6.51 gateway 192.168.0.1 how can i setup bridge interface correctly and how would my /etc/netwrok/interfaces file would look a like.

    Read the article

  • How to selectively route network traffic through VPN on Mac OSX Leopard?

    - by newtonapple
    I don't want to send all my network traffic down to VPN when I'm connected to my company's network (via VPN) from home. For example, when I'm working from home, I would like to be able to backup my all files to the Time Capsule at home and still be able to access the company's internal network. I'm using Leopard's built-in VPN client. I've tried unchecking "Send all traffic over VPN connection." If I do that I will lose access to my company's internal websites be it via curl or the web browser (though internal IPs are still reachable). It'd be ideal if I can selectively choose a set of IPs or domains to be routed through VPN and keep the rest on my own network. Is this achievable with Leopard's built-in VPN client? If you have any software recommendations, I'd like to hear them as well.

    Read the article

  • Email bouces to tell me it was delivered?

    - by flamey
    I get this back after sending an email. It says "Your message was successfully delivered", then why do I even get this? Or this phrase referes to something else? Reporting-MTA: dns; gmmr6.centrum.cz X-Postfix-Queue-ID: CDBBB8016CE1 X-Postfix-Sender: rfc822; [SENDER_EMAIL] Arrival-Date: Sat, 5 Mar 2011 22:04:41 +0100 (CET) Final-Recipient: rfc822; [RECIPIENT_EMAIL] Original-Recipient: rfc822;[RECIPIENT_EMAIL] Action: delivered Status: 2.0.0 Diagnostic-Code: X-Postfix; delivery via maildaemon: OK This is the mail system at host gmmr6.centrum.cz. Your message was successfully delivered to the destination(s) listed below. If the message was delivered to mailbox you will receive no further notifications. Otherwise you may still receive notifications of mail delivery errors from other systems. The mail system <[RECIPIENT_EMAIL]>;: delivery via maildaemon: OK

    Read the article

  • Dell PR03X port replicator and DisplayPort to DVI adapter not detecting second monitor

    - by yothenberg
    Hi, I have a dell M4400 connected to a PR03X port replicator/docking station. I use the DVI port to connect it to a first Dell 2208WFP monitor and I'm trying to use a DisplayPort-to-DVI adapter to connect it to a second Dell 2208WFP monitor. The second monitor, connected via the DisplayPort-to-DVI adapter immediately goes into sleep mode and the laptop doesn't detect it. What is really weird is that it did detect it the first time I plugged it in but after I unplugged the monitor and plugged it back in it stopped working. I swapped the monitors round and it detected them both but after unplugging the monitor connected via the DisplayPort-to-DVI and plugging it in again it stopped working. Both monitors work if plugged in directly to the DVI port. Is there some way to force re-detection? Any ideas? Thanks, Mark

    Read the article

  • Windows cannot find the host name "download.microsoft.com" using DNS

    - by joedotnot
    When trying to download a file found on the Microsoft downloads center that starts with, for example, http://download.microsoft.com/download/6/8/7/(some_GUID)/(some_file_name.ext) i get a timeout with "Internet Explorer cannot display the webpage". More information says: Internet connectivity has been lost. The website is temporarily unavailable. The Domain Name Server (DNS) is not reachable. The Domain Name Server (DNS) does not have a listing for the website's domain. If this is an HTTPS (secure) address, click Tools, click Internet Options, click Advanced, and check to be sure the SSL and TLS protocols are enabled under the security section. Diagnose Connection problems says: Windows cannot find the host name "download.microsoft.com" using DNS Bear with me while i expand on the problem: It all started when i tried to download Windows XP mode for my Windows 7 machine. I went to the virtual PC site, then thru the motions of Windows Genuine Advantage which validated ok, but when it redirects to grab the file just times out with above error. (NB: i also tried with the latest Chrome and Firefox but no use due to the Genuine Advantage stuff, so i decided to stick with IE). I am behind an ADSL2+ modem router connecting via wireless (Win 7 Pro laptop); so i hop over to the desktop connected via ethernet (Vista Business), and same result; begin to think site download.microsoft.com site is down. So i give it a break an read up on EDNS, flushing the cache, hosts file, etc... Try again an hour later on the Win 7 machine, still no go; so i turn off the Win 7 (software) firewall, and lo and behold, i can connect and grab any files from download.microsoft.com; (...nice, so we have a Micro$0ft firewall preventing access to a Micro$0ft website, no wonder my auto-updates kept failing but that's another story). But i still am not happy that the desktop connected via ethernet still cannot get to download.microsoft.com, even though i turned off all firewalls, defenders, anti-virus, etc. What is so special / specific about the url download.microsoft.com, any other site is ok, including www.microsoft.com. Any networking guru know what's REALLY going on, and how can i get the desktop to connect? Ping download.microsoft.com - Ping request could not find host download.microsoft.com. Please check the name and try again. Ping google.com or even www.microsoft.com works gives me an IP address. NB: On the wireless laptop ping download.microsoft.com works, i get xxxx.ms.akamai.net [202.7.177.33].

    Read the article

  • How many cron jobs are too many?

    - by guitar-
    I have a couple of cron jobs for basic maintenance which aren't very resource-intensive. I also have custom task scheduling (which is just calling a .php file and passing information via GET, ie: cronjob.php?param1=param ...). These can add up pretty quickly. These just call system commands and run external programs (Nmap is one of them). They usually don't take long either. Anyway, can anyone tell me, roughly what point is too many? I know it's hard to say since it depends on what job is being run and how often, but at what point does the crontab program start "struggling"? Anyone have any idea? Thanks.

    Read the article

  • Best Persistence choice for J2EE-App with frequently changing Data Model

    - by Ben-G
    Whenever I develop a J2EE-Application, I at some point decide to switch from my dummy Persistence (Simply Using Lists and other Data Structures) to some Sort of Database Persistence. Mostly when I hope the Data Model is more or less complete. From this point on, changes to the data model become exhausting, but unluckily they occur rather often. I've used different Object-Relational-Mappers (iBatis, Hibernate) for my projects. They definitely reduce the pain coming with Data Model changes, but they anyway let me adjust code/configuration at 3 or 4 places for every single change. To me, that's cumbersome and error prone. I made a better experience with DB4O, which simply persists Java Objects as they are, but I believe it's performance does not scale for huge applications. Is there anyway to maintain performance while letting out all the ugly configuration work? I'm seeking a performant framework which really hides persistence from my code. Wish for thinking? Or am I missing out THE technology? Hope you can help.

    Read the article

  • Sonicwall - dual WAN ports - switch from one to another

    - by Charles
    Hi, Folks! I'm using a SonicWall NSA 240 which has two WAN ports (T1 and Comcast) and the LAN port has a cable which connects to a switch. From the switch, several cables connect to other switches. The SonicWall doesn't have DHCP enabled; one of our domain controllers running Windows Server 2003 also functions as a DHCP server. Is there a way for a user in our network to change connection from T1 to Comcast as their ISP or vice versa? In other words, if a user is connected via the T1, can he/she somehow connect via Comcast instead? Thanks, in advance, for your help! Sincerely, Charles

    Read the article

  • Hostname problems in CentOS 5.5

    - by spoon16
    I just set up a CentOS 5.5 machine on my local network and attempted to modify the hostname by editing /etc/sysconfig/network file. When I'm logged in locally the change to the hostname is reflected and seems to be working fine. When I open a SSH session via PuTTY from Windows this is what I see at the prompt: [root@? ~]# cat /etc/sysconfig/network NETWORKING=yes NETWORKING_IPV6=yes HOSTNAME=mini.local [root@? ~]# sysctl kernel.hostname kernel.hostname = ? [root@? ~]# hostname ? [root@? ~]# hostname -f hostname: Unknown server error A couple of other symptoms that may be helpful in troubleshooting this problem. I can ping the CentOS box from my Windows machine via IP but not hostname. Also, my Netgear router does not display the hostname when I view the "Connected Devices", I do see the mac address and the proper IP listed though. How can I make it so that the hostname is properly propagated throughout my network?

    Read the article

  • XP Mode as a server, Win 7 as a client

    - by Spyro
    I have two virtual machines (XP Mode). They are connected to each other by a network setting - Internal Network. It is the only working setting. This is the only way I got two virtual XP to ping each other. Now I want to connect each of them from the application that runs on Windows 7 which is hosting both virtual machines, but I can't do that. The firewall on both XP-Mode machines is disabled. Any other networking setting added as additional adapter on Xp-Mode machine does not allow me to connect from Windows 7. So my question is this - how to enable connection from Windows 7 application to XP mode application (client - server)? Point 2 (pass message) work perfectly because of the "internal network" setting. The problem is point 1 and 3.

    Read the article

  • Nested RDP and ILO sessions, latency and keystroke repetition.

    - by ewwhite
    I'm working on a remote server installation entirely through ILO. Due to the software application and environment, my access is restricted to a Windows server that I must access through RDP. Going from that system to the target server is accomplished via HP ILO3. I'm trying to run a CentOS installation in an environment where I can't use a kickstart. I'm doing this via text mode, but the keystrokes are repeating randomly and it's difficult to select the proper installation options. I'm doing this using Microsoft's native RDP client (on Mac and Windows). I've also noticed this before when running installations or doing remote work in nested sessions. Is there a nice fix for this, or it it simply a function of the protocol?

    Read the article

  • how to change document root to public_html from root directory

    - by manish
    For testing I hosted my website on free server from 000webhost.com They have a directory structure:- (root folder) \ (public folder) \public_html this directory structure enables to keep all the library files in root folder and all public data in \public_html, so I developed my website accordingly, and my final structure looked like:- / /include(this folder contains library files) /logs(log files) /public_html /public_html/index.php /public_html/home.php /public_html/and other public files on 000webhost makes only public_folder available to be accessed via url and my url looked neat and clean like www.xample.com/index.php or www.example.com/home.php but after completion of development I moved website to shared host purchased from go-daddy.com, now they do not have any such kind of directory permission, all the files are kept in root folder and are accessible via url also url has become like:- www.example.com/public_html/home.php or www.example.com/public_html/index.php How should I redirect url request to public_html folder again so as to make library file unavailable to public access and make url neat and clean.

    Read the article

  • Logitech gamepad f710 and ubuntu and as an input to a python program

    - by wherestheforce
    I would like to use the Logitech F710 gamepad as an input device to a python program. I am using Ubuntu. I do not really know where to start, so here are a few questions: How does Ubuntu detect the gamepad? If the gamepad is recognized within Ubuntu, how would I interact with this device via a python script? If this is not easy to do in Ubuntu, how would I interact with the gamepad via a python script in Windows? Thanks!

    Read the article

  • Forwarding a subdomain to main domain using Godaddy

    - by Ryan Hayes
    I have current blog, which was hosted on Tumblr at http://blog.ryanhayes.net. I'm moving it over to http://ryanhayes.net, and have all the 301 redirects set up for the blog entries to map to my new blog, which is hosted using Godaddy (domain included). When I try to set up a subdomain forward, I'm greeted with a nice 403 Forbidden response (as of this writing, you can see it at http://blog.ryanhayes.net. When I try to ping both the subdomain and domain, they point to the same IP address, so I know blog subdomain has at least switched over to point to the same content. I don't really understand why I would get a 403 Forbidden on the same content that I can see perfectly fine via another domain. Currently, I have a CNAME of blog pointing to @, which is how "www" is set up to forward, so I'm assuming it would do the same thing. My question is what is the proper way to set up my DNS to make the blog subdomain forward to my main domain (301) using the GoDaddy DNS manager? Bonus: What is the background on why I am getting a 403 error the current way? Forbidden You don't have permission to access / on this server. Additionally, a 403 Forbidden error was encountered while trying to use an ErrorDocument to handle the request. UPDATE 12/7/2010 Error on site has been fixed, you can no longer view it from my site.

    Read the article

  • can ping, but not SSH

    - by Matt
    So I have NetworkManager, connected to an AP on wlan1. I have wlan0 connected to a AdHoc network. I have Firestarter sharing my inet on the Adhoc. I have my ipod connected to wlan0, IP 10.42.43.101. wlan0 Link encap:Ethernet HWaddr ac:xx:12:81:7f:xx inet addr:10.42.43.1 Bcast:10.255.255.255 Mask:255.0.0.0 wlan1 Link encap:Ethernet HWaddr 00:xx:b3:98:f2:xx inet addr:10.0.1.61 Bcast:10.0.1.255 Mask:255.255.255.0 Now, I can ping my Jailbroken, SSH-enabled and running ipod touch: matt: ~ $ ping 10.42.43.101 PING 10.42.43.101 (10.42.43.101) 56(84) bytes of data. 64 bytes from 10.42.43.101: icmp_req=1 ttl=64 time=168 ms 64 bytes from 10.42.43.101: icmp_req=2 ttl=64 time=256 ms 64 bytes from 10.42.43.101: icmp_req=3 ttl=64 time=151 ms ^C --- 10.42.43.101 ping statistics --- 3 packets transmitted, 3 received, 0% packet loss, time 1999ms rtt min/avg/max/mdev = 151.465/191.979/256.316/46.003 But I cannot SSH it: $ ssh [email protected] -vv OpenSSH_5.8p1 Debian-1ubuntu3, OpenSSL 0.9.8o 01 Jun 2010 debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for * debug2: ssh_connect: needpriv 0 debug1: Connecting to 10.42.43.101 [10.42.43.101] port 22. It just stays there till I ^C it.. Here's my routing: $ ip route show 10.0.1.0/24 dev wlan1 proto kernel scope link src 10.0.1.61 metric 2 10.0.1.0/24 dev wlan1 proto kernel scope link src 10.0.1.61 metric 319 169.254.0.0/16 dev vboxnet0 proto kernel scope link src 169.254.128.223 metric 204 10.0.0.0/8 dev wlan0 proto kernel scope link src 10.42.43.1 default via 10.0.1.1 dev wlan1 proto static default via 10.0.1.1 dev wlan1 metric 319

    Read the article

  • How to set User Tile image Windows Server 2012?

    - by moontear
    I found this nice article of how to add a user tile image via code: http://joco.name/2010/12/06/i-discovered-the-new-windows-user-tile-api/ This is also explained in depth here: http://msitpros.com/?p=1036 I have problems with doing this in Windows Server 2012. Whenever I run the code: using System; using System.Runtime.InteropServices; namespace FejesJoco { class Program { [DllImport("shell32.dll", EntryPoint = "#262", CharSet = CharSet.Unicode, PreserveSig = false)] public static extern void SetUserTile(string username, int whatever, string picpath); [STAThread] static void Main(string[] args) { SetUserTile(args[0], 0, args[1]); } } } I get an exception: Error HRESULT E_FAIL has been returned from a call to a COM component. Can anyone get this to work and add a user tile image via code?

    Read the article

  • Vim Stuck In Insert Mode

    - by Levi Hackwith
    I've been using Vim for several months now via my web host (they allow putty access). All of a sudden, the escape key has become unresponsive. I cannot exist insert or any other mode by simply hitting escape. I have to hit F1 which brings up the help in vim and kicks me into command mode. I'm most certain that my escape key on my keyboard is functioning fine since all of my windows shortcuts that use the escape key operate normally. I know this is a ridiculous question and I'm certain there's a lot more to look into regarding a solution. What I really need is a solid lead as to where to start looking. Things that might help: I'm using vim via putty I'm logging in using jailshell I'm not root

    Read the article

  • SharePoint 2010 and Windows Server Backup

    - by Enrique Lima
    A couple of months ago, a friend found a bit of information on TechNet that has proven to be quite useful. See, I am of the opinion SharePoint allows for smaller deployments to be made, and with that said, I am talking about SharePoint Foundation 2010 being used for the most part. But truly the point here is not to discuss whether or not a deployment of SharePoint Foundation 2010 or SharePoint Server 2010 is right or not.  The fact is they do take place and happen.  And information will reside there. Now, the point of this post is to raise awareness on options available for companies that have implemented it and maybe are a bit “iffy” on how to protect the information being placed in libraries and lists.  In many cases I have found SharePoint comes first and business continuity becomes an afterthought.  The documentation piece from TechNet states: “You can register SharePoint Server 2010 with Windows Server Backup by using the stsadm.exe -o -registerwsswriter operation to configure the Volume Shadow Copy Service (VSS) writer for SharePoint Server. Windows Server Backup then includes SharePoint Server 2010 in server-wide backups. When you restore from a Windows Server backup, you can select Microsoft SharePoint Foundation (no matter which version of SharePoint 2010 Products is installed), and all components reported by the VSS writer forSharePoint Server 2010 on that server at the time of the backup will be restored. Windows Server Backup is recommended only for use with for single-server deployments.” Even in the event of single-server deployments you will have options to safeguard your data. The process will require that after you have executed the stsadm command above, you will then use Windows Server Backup to do a Full Server Backup.  Then when the restore operation is needed you will be able to select specifically the section that has the SharePoint technologies backup. The restore process: Hope you find this to be a helpful post.  I have found this to be specially handy in SharePoint deployments that are part of a Team Foundation Server deployment and that are isolated from any other SharePoint farm and such.   Credits:  Sean McDonough for passing along the information available on TechNet.

    Read the article

  • Exempt programs from using active VPN connection

    - by Oxwivi
    When I connect to a VPN, all my network traffic is automatically routed through it. Is there a way to add exemptions to that? I don't know if adding exceptions has anything to do with the VPN protocol, but the VPN I'm using is of the OpenVPN protocol. Speaking of OpenVPN, why is it not installed by default on Ubuntu installs unlike PPTP? I could not get the list of IRCHighWay's servers, and this is the result I get trying to connect on XChat with running the bash script running: * Looking up irc.irchighway.net * Connecting to irc.irchighway.net (65.23.153.98) port 6667... * Connected. Now logging in... * You have been K-Lined. * *** You are not welcome on this network. * *** K-Lined for Open proxies are not allowed. (2011/02/26 01.21) * *** Your IP is 173.0.14.9 * *** For assistance, please email [email protected] and include everything shown here. * Closing Link: 0.0.0.0 (Open proxies are not allowed. (2011/02/26 01.21)) * Disconnected (Remote host closed socket). The IP 173.0.14.9 is the one due to my VPN. I had forgotten to check ip route list before running the script, and this is the one after running it: ~$ ip route list 99.192.193.241 dev ppp0 proto kernel scope link src 173.0.14.9 173.0.14.2 via 192.168.1.1 dev eth1 proto static 173.0.14.2 via 192.168.1.1 dev eth1 src 192.168.1.3 192.168.1.0/24 dev eth1 proto kernel scope link src 192.168.1.3 metric 2 169.254.0.0/16 dev eth1 scope link metric 1000 default dev ppp0 proto static Oh and running the script returned this output: ~$ sudo bash irc_route.sh Usage: inet_route [-vF] del {-host|-net} Target[/prefix] [gw Gw] [metric M] [[dev] If] inet_route [-vF] add {-host|-net} Target[/prefix] [gw Gw] [metric M] [netmask N] [mss Mss] [window W] [irtt I] [mod] [dyn] [reinstate] [[dev] If] inet_route [-vF] add {-host|-net} Target[/prefix] [metric M] reject inet_route [-FC] flush NOT supported I ran the script after connecting to the VPN.

    Read the article

< Previous Page | 257 258 259 260 261 262 263 264 265 266 267 268  | Next Page >