Search Results

Search found 39405 results on 1577 pages for 'zeta two'.

Page 262/1577 | < Previous Page | 258 259 260 261 262 263 264 265 266 267 268 269  | Next Page >

• MDADM RAID5 array showing as CLEAN FAULTY

  - by Dean Reilly

  A drive dropped out of my raid 5 array yesterday. It looks like the reason was due to a bad controller so I switched it out and attempted to re-add the drive but mdadm claimed it couldn't do it. So I zerod the superblock and just added the drive normally and left it to resync. When I came to check on the array this morning I was unable to mount it at all and it's now showing as CLEAN FAULTY with two drives missing. The two missing drives are listed as spare and faulty spare. Is there anything I can do in this situation or is the array gone?

  Read the article

• Routing application traffic through specific interface

  - by UnicornsAndRainbows

  Hello All! First question here, so please go easy: I have a debian linux 5.0 server with two public interfaces. I would like to route outbound traffic from one instance of an application via one interface and the second instance through the second interface. There are some challenges: both instances of the application use the same protocol both instances of the application can access the entire internet (can't route based on dest network) I can't change the code of the application I don't think a typical approach to load balancing all traffic is going to work well, because there are relatively few destination servers being accessed in the outbound traffic, and all traffic would really need to be distributed pretty evenly across these relatively few servers. I could probably run two virtualized servers on the box and bind each of them to a different external ip, but I'm looking for a simpler solution, maybe using iproute or iptables? Any ideas for me? Thanks in advance - and I'm happy to answer any questions.

  Read the article

• Signal strength and Speed of wireless network

  - by Tim

  As shown by Lenovo Access Connections on my Windows 7, the wireless network I am using has a speed of 54.0Mbps but a signal strength of 88%. I am using WinSCP with unlimited speed to download files. WinSCP shows that the speed fluctuates between 100 and 120KiB/s. I was wondering what are the difference between the two speeds from Lenovo Access Connections and WinSCP? How can I tell the actual speed performance, for example, from the above measurements: speeds and the signal strength mentioned in the two places. Thanks and regards!

  Read the article

• Apache - Same username in several .htpasswd files

  - by greydet

  In a virtual host, I setup two different <Location> blocks for which the access is restricted by two basic authentication htpasswd files. One htpasswd contains different usernames + a common user name. The other htpasswd file only contains the common user name. My problem is that once users connect a location with the common user name, they have immediate access to the other location without being asker for a different user name. Is there a way to restrict the username access only to the corresponding htpasswd file? Is there a way for users to ask to be re-prompted for another username/password?

  Read the article

• How to connect a wifi router to a cable modem router?

  - by DavidD

  Here's the thing: I have a cable modem router (Thomson TCW710) with wifi-g that I rent from my cable company. I would like to use a wireless-n router (D-Link DIR-655, that I received for free) with it in order to take advantage of the faster wifi. I basically need advice on how to architecture my home network with these two beasts. What configuration should I need to apply on my old and new router to make it all work? The two routers will of course be connected together with a RJ-45 cable.

  Read the article

• Primary/secondary ethernet interfaces via NetworkManager in Ubuntu 9.10

  - by Josh

  I have an Ubuntu 9.10 machine with three ethernet interfaces, eth0, eth1 and eth2. eth2 is connected to a private network. eth0 and eth2 are connected to two different LANs. Either one will provide access to the internet. All three networks have DHCP servers. Using Ubuntu's the default settings (And Gnome), when I boot up all the interfaces are active and my system gets three IP addresses. However any attempt to access the internet results in connection timeouts and other weirdness. I suspect that traffic is going out on one NIC (like eth0) and coming back in on another (like eth1). I'm not sure what's going on. The only way I can access the internet at the moment is to bring two of the devices down with ifdown. How can I configure eth0 as my primary interface so all trafic goes out by default on that interface, while keeping the other two active? Also, I want to make sure Avahi broadcasts properly on all three IPs so that the computers on the LAN of eth1 can still connect to myHostname.local... EDIT: Here's my routing table: Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 172.16.151.0 0.0.0.0 255.255.255.0 U 0 0 0 eth2 172.16.30.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 10.1.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth1 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth1 0.0.0.0 172.16.30.2 0.0.0.0 UG 0 0 0 eth0 0.0.0.0 10.1.0.1 0.0.0.0 UG 0 0 0 eth1 I want the 172.16.30.2 network to be the primary one and the 10.1.0.0 network to be the secondary one. EDIT2: My nameservers are also incorrect. It seems like Ubuntu is bringing the networks up in order, eth0, then 1, then 2, and the DHCP information from eth1 is overriding eth0, and eth2 is overriding eth1. How can I reverse this so the DHCP information from eth0 is the "master"? EDIT3: This seems to be an issue with Gnome's NetworkManager.

  Read the article

• emulate dual monitor using a second machine

  - by Hemal Pandya

  I have monitors of my two machines side by side and I use them both with a single keyboard/mouse using Google Synergy+ which works great. But is it possible to use the monitor of my secondary machine as the secondary monitor of my primary? I am on XP so from what I understand I cannot just rdc from secondary to this primary. In any case that would be a different session altogether and I would prefer to be able to extend my desktop over the two monitors. Any solutions or suggestions? Thanks in advance.

  Read the article

• Request Coalescing in Nginx

  - by Marcel Jackwerth

  I have an image resize server sitting behind an nginx server. On a cold cache two clients requesting the same file could trigger two resize jobs. client-01.net GET /resize.do/avatar-1234567890/300x200.png client-02.net GET /resize.do/avatar-1234567890/300x200.png It would be great if only one of the requests could go through to the backend in this situation (while the other client is set 'on-hold'). In Varnish there seems to be such a feature, called Request Coalescing. However that seems to be a Varnish-specific term. Is there something similar for Nginx?

  Read the article

• Difference between ps output and top output?

  - by Soumya Prasad Ukil

  I find it difficult to understand the output produced by ps and top? This is the output by top: PID PSID USERNAME TID PRI NICE SIZE RES STATE TIME CPU COMMAND 26439 23712 soumyau 26439 15 0 7512M 5234M sleep 286:25 16.67% or_lse2 (18) 26523 23712 soumyau 26439 -2 0 7512M 5234M cpu9 143:10 8.33% or_lse2 26522 23712 soumyau 26439 -2 0 7512M 5234M cpu3 143:10 8.33% or_lse2 This is by ps (ps -L -p 26439 -o pcpu,psr,pid,user,tid): %CPU PSR PID USER TID 99.9 3 26439 soumyau 26522 99.9 9 26439 soumyau 26523 0.0 8 26439 soumyau 26439 Why are there differences in two result? Can you briefly explain the significance of the two CPU% ?

  Read the article

• emulate dual monitor using a second machine

  - by Hemal Pandya

  I have monitors of my two machines side by side and I use them both with a single keyboard/mouse using Synergy+ (now hosted at Google Code) which works great. But is it possible to use the monitor of my secondary machine as the secondary monitor of my primary? I am on XP so from what I understand I cannot just rdc from secondary to this primary. In any case that would be a different session altogether and I would prefer to be able to extend my desktop over the two monitors. Any solutions or suggestions? Thanks in advance.

  Read the article

• Sync Banshee library data.

  - by Dom

  I use Banshee to organise my music, I particularly like its scoring system and I have smart playlists based on it. However, I have two versions of my music library, one on each of my computers. As one of the computers is small I only have a favourite set of songs on that computer rather than my whole collection. The computers are not on a local network, but I do use Ubuntu One for file sharing between them. Is there any way I can synchronise song data (play count, score, skip count ...) and playlist data (including smart playlists that include songs based on this data) between the two computers? This would only be relevant of course for the songs that exist on both computers, the songs that exist on only one would need to be ignored. I did consider putting the library data file (I think it is .xml but I'm not sure) into the shared file and creating a symbolic link to it, but then I wouldn't be able to have a different set of songs on each computer. Thank you.

  Read the article

• How can I shut down all my Virtual Machines when my UPS kicks in?

  - by Tim

  I have a Dell T610 running ESXi4, an APC Smart UPS 1000VA and a local "console" machine running Vista and the vSphere 4 Essentials pack. A dedicated management network is in place between the T610 and the Vista machine. We have 4 VMs: SBS 2003, Server 2003 running Terminal Services, and two XP Machines. Ideally, when the UPS is forced to use battery power [for a set number minutes], I would like to gracefully shutdown all the VMs, then the ESXi, then the console machine. The latter two are not strictly a priority, but the VMs within ESXi are. Google provided lots of deprecated scripts that used to work on ESXi 3.x or similar, however I am unable to find what they were deprecated by. What do I need to be able to do this? I have Powerchute Express as supplied with the UPS, but would be willing to pay for software if required.

  Read the article

• Filtering Client IP from Access Log for Urchin

  - by Ram Prasad

  I have some apache logs to process, and since the webserver behind two levels of reverse proxies, I am getting two IPs in the X-Forwarded-For header.. for example: 208.34.234.55, 127.0.0.1 - - [29/Oct/2009:21:38:13 -0500] "GET /monkey.html HTTP/1.0" 200 20845 0 0 "http://www.monkey.com/" "Mozilla/5.0 (Windows; U; Windows NT 5.1; en-US; rv:1.9.0.15) Gecko/2009101601 Firefox/3.0.15 (.NET CLR 3.5.30729)" Now, how do I filter this in Urchin (or remove this in Apache logging) so, 127.0.0.1 is removed from processing. Currently urchin is not able to recognize the multuple IP address so it does not log the remote IP

  Read the article

• ATI AMD Radeon 6670M 2GB Dual External monitors

  - by kellax

  I have HP Pavilion dv7 BeatsAudo model: dv7-6b with following specifications: CPU: Intel i7-2670QM ( Quad Core ) 8 CPU's @ 2.2Ghz RAM: 8GB @ 1066 GPU: ATI Radeon HD 6770M 1GB Notebook has two slots: HDMI and VGA On my VGA i have an external monitor 24" Samsung, any idea if my notebook could support a second external monitor as well. I do a lot of development work, i havent got a second monitor to test it yes but i know there can be problems. I would like to have a monitor connected on my VGA and on my HDMI so two external monitors and notebooks monitor. Would this be viable ?

  Read the article

• Accessing shared resource on local computer from users of different physical location

  - by Joe

  Sounds like easy task to some but such a difficult task for me to do... The main requirement for this task is to setup something in offices located on different locations, so (1st question) users are able to log on to the domain without VPN when they are in one of the offices. Additionally, (2nd question)how they can log on to the domain server when they are on the road like in a starbuck, what do they have to do to connect to domain after VPN connection are successful. also it's my understanding that, we can't share resource from computers on different network segments, (3rd question)what is the best solution to bridge/combine two network segments(two office in different locations) so computers of different location can see each other. Thank you in advance for any response.

  Read the article

• setting up a private network using linksys router

  - by user287745

  scenerio:- a database server running sql server 2005 and sql server management studio 2005 express editions a web server running IIS 5.0v using windows xp pro. two other computer having windows xp and windows 98 i have a linksys router which i use to access point for wireless (laptop) there are 5 sockets behind it four for clients and one for internet. i would like to setup a LAN- something like a private hosting area with two clients. would should i do? where to connect what and what would the changes in settnigs be. right now it uses dhcp or something to assign ips. where will the webserver be attached to the internet socket? where will the db server be attached? any guide, links, help thank you

  Read the article

• Design Question

  - by dturner71

  Can I have two independent Connection servers attached to the same vCenter server? Here's my scenario. I'm setting up View 4 to provide desktops to two seperate Windows domains that are on different IP subnets seperated by a firewall. One cluster of physical servers, one vCenter server, linked clones. As I understand it View Connection server has to be a member of a Windows domain in order for quickprep to work. So the way to provide desktops to both Windows domains is to have a Connection server in each one right? Then open ports in the firewall so the Connection server from the other subnet can communicate with vCenter. Any reason why this won't work? Or is there a better way to accomplish it?

  Read the article

• Connecting server to more than one switch.

  - by Jake

  I have 3 switches, one NEATGEAR GS748T and two JGS524. Initially I wanted to connect them in a triangle loop, but later suspect that the JG524 does not have spanning tree support. Now I have a Dell R710 with 2 NIC at the back. If I connect the server in between the two JGS524, which both in turn connect to the GS748T, will that consitute a loop? According to my limited understanding, with 2 NICs there will be 2 IPs for the server. Will the file server even work or not? Theoretically speaking, will this configuration increase the access speeds for clients? Thanks.

  Read the article

• Cross-Forest Trust

  - by cdalley

  I am looking at testing a cross-domain trust we can have two domain controllers (with different forests and domain names) setup so we can move everyone onto the new domain. We do NOT run exchange on site and we do not have any links to O365 to AD currently. Onto the problem: I have setup two DCs in a Virtual Machine: They are on the same network 192.168.0.* The Windows 2003 server: Name: OLDSRVR "Clone" of our current Domain Controller IP: 192.168.0.1 Domain: internal.test.com The Windows 2012 server: Name: ADCTEST01 Brand new domain setup from scratch separate to internal.test.com Domain: internal.test2.com IP: 192.168.0.2 OLDSRVR can only see ADCTEST if it has dynamic IP set. If I set a static IP it cannot see it. If I try using the dynamic IP and try to join it gets to the end then complains "??The trust relationship between this workstation and the primary domain failed" Any ideas?

  Read the article

• Why are applications slowing down on the computer's second monitor?

  - by ChristianLinnell

  Here's an interesting one. Problem I have a user on Windows XP who is running a web application inside IE8. She has two monitors plugged in via DVI cables. When she is working the the browser on her primary monitor, everything is fine, but when she drags the window over to the second monitor, the web applications functionality grinds to a halt. It's not just web apps either - many applications exhibit the problem. What I've tried Switching the two monitors in the OS. It's obviously not the monitor's fault. Confirmed that it's the app slowing down, and not the graphical rendering. The application in question actually locks up. The mouse is unaffected, and I can drag other windows on top of the problematic application. Any ideas?

  Read the article

• Multiple IP Addresses on a Traceroute Line

  - by Paul

  I'm doing a traceroute from my box to ....say.... stackoverflow.com. I see a couple of instances where there are multiple ip's on one line. For instance, in below, line #2 has two IPs: 10.1.6.5 and 10.1.4.5 Also on line #4, there are two timestamps after 216.182.236.96: 0.653 ms and 0.637 ms What are these? This is on Linux Traceroute example: traceroute to www.stackoverflow.com (198.252.206.16), 30 hops max, 60 byte packets 2 ip-10-1-6-5.us-west-1.compute.internal (10.1.6.5) 0.329 ms 0.425 ms ip-10-1-4-5.us-west-1.compute.internal (10.1.4.5) 0.471 ms 4 216.182.236.104 (216.182.236.104) 0.554 ms 216.182.236.96 (216.182.236.96) 0.653 ms 0.637 ms 5 205.251.230.64 (205.251.230.64) 0.616 ms 205.251.229.232 (205.251.229.232) 1.305 ms 205.251.230.64 (205.251.230.64) 0.573 ms

  Read the article

• identifying windows service

  - by András

  On my win7 machine when I watch a movie in XBMC, once per hour the desktop regains the focus. The movie keeps playing, but in the background now, so I can only hear it. It is quite irritating. I noticed, that the Windows Application log always contains two entres for this time: "The description for Event ID 0 from source Self-service Plug-in cannot be found. Either the component that raises this event is not installed on your local computer or the installation is corrupted. You can install or repair the component on the local computer." One entry is for starting, and one for stopping 60 seconds later. This keeps repeating, every two starts 3600 seconds apart. How can I repair it? How can I find out which service it is?

  Read the article

• Routing Traffic on Ubuntu to give Raspberry PI Internet Access

  - by Scruffers

  I'm hoping someone can point me in the right direction for setting up my Linux (Ubuntu 12.04) box to route traffic from eth0 to wlan0. I'll try and explain the problem I am trying to solve: I currently have two separate networks: [RaspberryPi/eth0] 192.168.2.2 / 255.255.255.0 ^ | v [Ubuntu/eth0] 192.168.2.1 / 255.255.255.0 And: [Ubuntu/wlan0] 192.168.1.100 / 255.255.255.0 ^ | v [ADSL router] 192.168.1.1 / 255.255.255.0 So currently if I want to access the RaspberryPI I can SSH from the Ubuntu box to the PI. And if I want to use the Internet, I have full access from the Ubuntu box, but nothing from the RaspberryPI - the two networks are partitioned. What I would like to do is configure things so that the RaspberryPI has Internet access via the Ubuntu box and out to the Internet. I tried to create a bridge, but got the message "wlan0: operation not supported" (wireless chipset is Ralink RT3062). I'm sure giving the Raspberry PI Internet access should be easy to do in this configuration, but I am a bit lost - can someone point me in the right direction please?

  Read the article

• mdadm - Recovering a 'split' RAID1 array

  - by Hamza

  I have two drives that used to be part of a single RAID1 volume but it appears that one of them went offline for some time, something I've noticed just now when I rebooted my system. I now seem to have two RAID volumes, as reported by: # cat /proc/mdstat Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] md126 : active raid1 sdc[1] 2096116 blocks super 1.2 [2/1] [_U] md127 : active (auto-read-only) raid1 sdb[0] 2096116 blocks super 1.2 [2/1] [U_] unused devices: <none> Not exactly sure where to go from here. How can I merge and re-sync these volumes without data loss? Thanks.

  Read the article

• Error while trying to configure VLAN with Open vSwitch

  - by Abhishek Chanda

  I am trying to connect a number of VMs using Open vSwitch. The VMs are on two separate physical boxes. Here is what I did: Created two tap devices on one physical host sudo ip tuntap add mode tap tap0 and same for tap1 Bring them up sudo ip link set tap0 up Add them as ports to Open vSwitch (br0 was created as a OVS bridge previously) sudo ovs-vsctl add-port br0 tap0 tag=1 Now I booted the VMs (using VirtualBox) and assigned addresses 192.168.122.11 and 192.168.122.12. Now when I try to ping one VM from another, I get the error Connect: network is unreachable. Since both VMs are connected to the switch on the same VLAN, I expect to be able to ping one from another. What is going wrong here?

  Read the article

< Previous Page | 258 259 260 261 262 263 264 265 266 267 268 269  | Next Page >