Search Results

Search found 30511 results on 1221 pages for 'linux networking'.

Page 263/1221 | < Previous Page | 259 260 261 262 263 264 265 266 267 268 269 270  | Next Page >

  • Home and Small to Medium Enterprise network manufacturer choice, Netgear, Linksys or D-Link ?

    - by Kedare
    (Please don't close this post, it's a serious post so... Be cool, no trolls please, I need an answer ;p) Hello, I am looking for an alternative to Cisco (too expensive for me !) for semi-pro utilization (at home but with advanced feature (I'm studying in IT)) and in small/medium enterprises. I think I will choose between LinkSys (Including Cisco Small Business), Netgear and D-Link, but I've never really used these products, that what I need is a manufacturer that make "almost" all type of networking equipment (Like Cisco but cheaper..), here are my needs : I need almost all my products to be rackable I need a good warranty (Netgear lifetime waranty rulez!) I need an "unified" network environment I made a little comparison of the characteristics that interest me after hours of search on Internet (based on result found on many websites): (Prices are based on the ldlc-pro.com french website) Hotline/Support Quality: Netgear : Not so bad Linksys : Not so bad D-Link : Poor! Most common Warranty: Netgear : Unlimited Lifetime Warranty! Linksys : Limited 3 years warranty D-Link : Limited 5 years warranty (Unlimited in US but I'm on France :(...) VPN protocols compatibles with routers on endpoint mode: Netgear : Only IPSEC :( Linksys : IPSEC, PPTP, L2TP D-Link : IPSEC, PPTP, L2TP Cheaper 8 ports Gb switch : Netgear : 30€ Linksys : 47€ D-Link : 30€ Cheaper 48 ports + 1Gb uplink(s) administrable switch : Netgear : 263€ Linksys : 630€ D-Link : 600€ Cheaper VPN router : Netgear : 100€ Linksys : 80€ D-Link : 60€ Cheaper rackable switch : Netgear : 50€ Linksys : 87€ D-Link : 50€ Cheaper rackable and administrable switch : Netgear : 120€ Linksys : 370€ D-Link : 171€ Netgear and D-Link are in the same range of price, where Linksys is more expensives. I've searched for some other criteria ( the full comparison is here, in french with shop/source links: http://forums.jeuxonline.info/showthread.php?t=1072280 ) and made a final score for each manufacturer : SCORE including IP camera sub-score: Netgear : 6.2/10 Linksys : 7.3/10 D-Link : 7.0/10 SCORE excluding IP camera sub-score: Netgear : 6.9/10 Linksys : 7.0/10 D-Link : 6.7/10 On both case, Linksys wins. So here is my little comparison, but because I've never really used these stuffs, I need your help to make a decision on witch manufacturer choose for both my personnal and corporate use. So here are the questions : What manufacturer do you recommend me (Not cisco (except Small business)) ? Why ? Have you called the call center of the customer support of one of these manufacturer ? How it was ? Did you had problems or bad experiences with these equipments ? Any other advices ? ;) Thank you !

    Read the article

  • DSL Modem with Wireless Router

    - by David
    I have a D-Link WBR-1310 wireless router and a TP-Link TD-8616 DSL modem. My old DSL modem died recently and I got the TP-Link as a replacement. With my old DSL modem, I plugged it into the WAN port on my D-Link and I could reach the internet through wireless and through the network. However, when I plugged the new TP-Link into the WAN port, I was not able to get any internet connectivity (either on the network ports or through wireless). So I plugged my labtop directly into the TP-Link DSL modem and I was able to get internet connectivity. I'm trying to figure out why my labtop can see the internet connection, but not the D-Link router. I think that the problem is due to the IP networking. My D-Link was originally set to have IP address 192.168.1.1. According to the documentation for the TP-Link DSL modem, it uses 192.168.1.1 as its IP address. I do not believe that my old DSL modem had an IP address. I logged into my D-Link router and changed its IP address to 192.168.1.2 and restarted it. Unfortunately, I still could not see the internet from my wireless devices. I've read a few forum postings which implied that I needed to setup a "bridge" between the two networks. Does that sound correct? Why didn't my old DSL modem require a bridge? I read pg. 12-13 of my D-Link's manual and they suggest that I need to disable UPnP, DHCP, and then plug the DSL modem into one of the LAN ports on my router. I'm concerned about doing this since I don't think that the firewall will work if I plug my DSL modem into one of the LAN ports. I also have a home NAS on my network and I wouldn't want that to be available over the internet. Does anyone have any advice about how I can get my TPLink DSL modem to work with my D-Link router? Thanks!

    Read the article

  • pfSense 2.1 OpenVPN client not using tunnelled interface

    - by Brian M. Hunt
    I'm having some trouble getting OpenVPN working on my pfSense box. The issue is quite strange to me. When I have the OpenVPN turned on, only my router is able to connect to the Internet. From the router I can use ping, links, etc., and connections work exactly as expected - through the VPN, with the IP address assigned by my VPN provider (Proxy.sh, incidentally). However, none of the clients on the local network can connect to the Internet. I get timeouts when using ping or a web browser. I can ping my router, and the IP address of the gateway. When I switch the default gateway from the VPN to my ISP's gateway, all works exactly as expected. Here the routing table (netstat -r) when in VPN mode, and a key for it: IPv4 Destination Gateway Flags Refs Use Mtu Netif Expire 0.0.0.0/1 10.XX.X.53 UGS 0 122 1500 ovpnc1 = default 10.XX.X.53 UGS 0 235 1500 ovpnc1 8.8.8.8 10.XX.X.53 UGHS 0 82 1500 ovpnc1 10.XX.X.1/32 10.11.0.53 UGS 0 0 1500 ovpnc1 10.XX.X.53 link#12 UH 0 0 1500 ovpnc1 10.XX.X.54 link#12 UHS 0 0 16384 lo0 ZZ.XX.XXX.0/20 link#1 U 0 83 1500 re0 ZZ.XX.XXX.XXX link#1 UHS 0 0 16384 lo0 127.0.0.1 link#9 UH 0 12 16384 lo0 128.0.0.0/1 10.11.0.53 UGS 0 123 1500 ovpnc1 192.168.1.0/24 link#11 U 0 1434 1500 ue0 192.168.1.1 link#11 UHS 0 0 16384 lo0 YYY.YYY.YYY.YYY/32 ZZ.XX.XXX.1 UGS 0 249 1500 re0 IP addresses 10.XX.X.53/54 - My DHCP-assigned IP address/pair from the VPN provider ZZ.XX.XXX.XXX - My external IP assigned by my ISP YYY.YYY.YYY.YYY - The external IP assigned by the VPN provider Interfaces ovpnc1 - My VPN client interface re0 - My LAN interface ue0 - My WAN interface This looks essentially what I would expect it to be. The default route is through the VPN provider. The VPN address is routed through the ISP-assigned IP address. I am not sure what would be wrong here. So figuring this was a firewall issue, I basically tried enabling all in/out traffic. This did not seem to remedy the problem. Also figuring it could possibly be some client networking issue, I restarted the clients on the LAN. This did not help. I also ran route flush and reset the routes manually. So I am a bit stumped, and would be very grateful for any thoughts on what the problem might be.

    Read the article

  • How do I protect a low budget network from rogue DHCP servers?

    - by Kenned
    I am helping a friend manage a shared internet connection in an apartment buildling with 80 apartments - 8 stairways with 10 apartments in each. The network is laid out with the internet router at one end of the building, connected to a cheap non-managed 16 port switch in the first stairway where the first 10 apartments are also connected. One port is connected to another 16 port cheapo switch in the next stairway, where those 10 apartments are connected, and so forth. Sort of a daisy chain of switches, with 10 apartments as spokes on each "daisy". The building is a U-shape, approximately 50 x 50 meters, 20 meters high - so from the router to the farthest apartment it’s probably around 200 meters including up-and-down stairways. We have a fair bit of problems with people hooking up wifi-routers the wrong way, creating rogue DHCP servers which interrupt large groups of the users and we wish to solve this problem by making the network smarter (instead of doing a physical unplugging binary search). With my limited networking skills, I see two ways - DHCP-snooping or splitting the entire network into separate VLANS for each apartment. Separate VLANS gives each apartment their own private connection to the router, while DHCP snooping will still allow LAN gaming and file sharing. Will DHCP snooping work with this kind of network topology, or does that rely on the network being in a proper hub-and-spoke-configuration? I am not sure if there are different levels of DHCP snooping - say like expensive Cisco switches will do anything, but inexpensive ones like TP-Link, D-Link or Netgear will only do it in certain topologies? And will basic VLAN support be good enough for this topology? I guess even cheap managed switches can tag traffic from each port with it’s own VLAN tag, but when the next switch in the daisy chain receives the packet on it’s “downlink” port, wouldn’t it strip or replace the VLAN tag with it’s own trunk-tag (or whatever the name is for the backbone traffic). Money is tight, and I don’t think we can afford professional grade Cisco (I have been campaigning for this for years), so I’d love some advice on which solution has the best support on low-end network equipment and if there are some specific models that are recommended? For instance low-end HP switches or even budget brands like TP-Link, D-Link etc. If I have overlooked another way to solve this problem it is due to my lack of knowledge. :)

    Read the article

  • IPsec tunnel to Android device not created even though there is an IKE SA

    - by Quentin Swain
    I'm trying to configure a VPN tunnel between an Android device running 4.1 and a Fedora 17 Linux box running strongSwan 5.0. The device reports that it is connected and strongSwan statusall returns that there is an IKE SA, but doesn't display a tunnel. I used the instructions for iOS in the wiki to generate certificates and configure strongSwan. Since Android uses a modified version of racoon this should work and since the connection is partly established I think I am on the right track. I don't see any errors about not being able to create the tunnel. This is the configuration for the strongSwan connection conn android2 keyexchange=ikev1 authby=xauthrsasig xauth=server left=96.244.142.28 leftsubnet=0.0.0.0/0 leftfirewall=yes leftcert=serverCert.pem right=%any rightsubnet=10.0.0.0/24 rightsourceip=10.0.0.2 rightcert=clientCert.pem ike=aes256-sha1-modp1024 auto=add This is the output of strongswan statusall Status of IKE charon daemon (strongSwan 5.0.0, Linux 3.3.4-5.fc17.x86_64, x86_64): uptime: 20 minutes, since Oct 31 10:27:31 2012 malloc: sbrk 270336, mmap 0, used 198144, free 72192 worker threads: 8 of 16 idle, 7/1/0/0 working, job queue: 0/0/0/0, scheduled: 7 loaded plugins: charon aes des sha1 sha2 md5 random nonce x509 revocation constraints pubkey pkcs1 pkcs8 pgp dnskey pem openssl fips-prf gmp xcbc cmac hmac attr kernel-netlink resolve socket-default stroke updown xauth-generic Virtual IP pools (size/online/offline): android-hybrid: 1/0/0 android2: 1/1/0 Listening IP addresses: 96.244.142.28 Connections: android-hybrid: %any...%any IKEv1 android-hybrid: local: [C=CH, O=strongSwan, CN=vpn.strongswan.org] uses public key authentication android-hybrid: cert: "C=CH, O=strongSwan, CN=vpn.strongswan.org" android-hybrid: remote: [%any] uses XAuth authentication: any android-hybrid: child: dynamic === dynamic TUNNEL android2: 96.244.142.28...%any IKEv1 android2: local: [C=CH, O=strongSwan, CN=vpn.strongswan.org] uses public key authentication android2: cert: "C=CH, O=strongSwan, CN=vpn.strongswan.org" android2: remote: [C=CH, O=strongSwan, CN=client] uses public key authentication android2: cert: "C=CH, O=strongSwan, CN=client" android2: remote: [%any] uses XAuth authentication: any android2: child: 0.0.0.0/0 === 10.0.0.0/24 TUNNEL Security Associations (1 up, 0 connecting): android2[3]: ESTABLISHED 10 seconds ago, 96.244.142.28[C=CH, O=strongSwan, CN=vpn.strongswan.org]...208.54.35.241[C=CH, O=strongSwan, CN=client] android2[3]: Remote XAuth identity: android android2[3]: IKEv1 SPIs: 4151e371ad46b20d_i 59a56390d74792d2_r*, public key reauthentication in 56 minutes android2[3]: IKE proposal: AES_CBC_256/HMAC_SHA1_96/PRF_HMAC_SHA1/MODP_1024 The output of ip -s xfrm policy src ::/0 dst ::/0 uid 0 socket in action allow index 3851 priority 0 ptype main share any flag (0x00000000) lifetime config: limit: soft 0(bytes), hard 0(bytes) limit: soft 0(packets), hard 0(packets) expire add: soft 0(sec), hard 0(sec) expire use: soft 0(sec), hard 0(sec) lifetime current: 0(bytes), 0(packets) add 2012-10-31 13:29:08 use - src ::/0 dst ::/0 uid 0 socket out action allow index 3844 priority 0 ptype main share any flag (0x00000000) lifetime config: limit: soft 0(bytes), hard 0(bytes) limit: soft 0(packets), hard 0(packets) expire add: soft 0(sec), hard 0(sec) expire use: soft 0(sec), hard 0(sec) lifetime current: 0(bytes), 0(packets) add 2012-10-31 13:29:08 use - src ::/0 dst ::/0 uid 0 socket in action allow index 3835 priority 0 ptype main share any flag (0x00000000) lifetime config: limit: soft 0(bytes), hard 0(bytes) limit: soft 0(packets), hard 0(packets) expire add: soft 0(sec), hard 0(sec) expire use: soft 0(sec), hard 0(sec) lifetime current: 0(bytes), 0(packets) add 2012-10-31 13:29:08 use - src ::/0 dst ::/0 uid 0 socket out action allow index 3828 priority 0 ptype main share any flag (0x00000000) lifetime config: limit: soft 0(bytes), hard 0(bytes) limit: soft 0(packets), hard 0(packets) expire add: soft 0(sec), hard 0(sec) expire use: soft 0(sec), hard 0(sec) lifetime current: 0(bytes), 0(packets) add 2012-10-31 13:29:08 use - src 0.0.0.0/0 dst 0.0.0.0/0 uid 0 socket in action allow index 3819 priority 0 ptype main share any flag (0x00000000) lifetime config: limit: soft 0(bytes), hard 0(bytes) limit: soft 0(packets), hard 0(packets) expire add: soft 0(sec), hard 0(sec) expire use: soft 0(sec), hard 0(sec) lifetime current: 0(bytes), 0(packets) add 2012-10-31 13:29:08 use 2012-10-31 13:29:39 src 0.0.0.0/0 dst 0.0.0.0/0 uid 0 socket out action allow index 3812 priority 0 ptype main share any flag (0x00000000) lifetime config: limit: soft 0(bytes), hard 0(bytes) limit: soft 0(packets), hard 0(packets) expire add: soft 0(sec), hard 0(sec) expire use: soft 0(sec), hard 0(sec) lifetime current: 0(bytes), 0(packets) add 2012-10-31 13:29:08 use 2012-10-31 13:29:22 src 0.0.0.0/0 dst 0.0.0.0/0 uid 0 socket in action allow index 3803 priority 0 ptype main share any flag (0x00000000) lifetime config: limit: soft 0(bytes), hard 0(bytes) limit: soft 0(packets), hard 0(packets) expire add: soft 0(sec), hard 0(sec) expire use: soft 0(sec), hard 0(sec) lifetime current: 0(bytes), 0(packets) add 2012-10-31 13:29:08 use 2012-10-31 13:29:20 src 0.0.0.0/0 dst 0.0.0.0/0 uid 0 socket out action allow index 3796 priority 0 ptype main share any flag (0x00000000) lifetime config: limit: soft 0(bytes), hard 0(bytes) limit: soft 0(packets), hard 0(packets) expire add: soft 0(sec), hard 0(sec) expire use: soft 0(sec), hard 0(sec) lifetime current: 0(bytes), 0(packets) add 2012-10-31 13:29:08 use 2012-10-31 13:29:20 So a xfrm policy isn't being created for the connection, even though there is an SA between device and strongswan. Executing ip -s xfrm policy on the android device results in the following output: src 0.0.0.0/0 dst 10.0.0.2/32 uid 0 dir in action allow index 40 priority 2147483648 share any flag (0x00000000) lifetime config: limit: soft (INF)(bytes), hard (INF)(bytes) limit: soft (INF)(packets), hard (INF)(packets) expire add: soft 0(sec), hard 0(sec) expire use: soft 0(sec), hard 0(sec) lifetime current: 0(bytes), 0(packets) add 2012-10-31 13:42:08 use - tmpl src 96.244.142.28 dst 25.239.33.30 proto esp spi 0x00000000(0) reqid 0(0x00000000) mode tunnel level required share any enc-mask 00000000 auth-mask 00000000 comp-mask 00000000 src 10.0.0.2/32 dst 0.0.0.0/0 uid 0 dir out action allow index 33 priority 2147483648 share any flag (0x00000000) lifetime config: limit: soft (INF)(bytes), hard (INF)(bytes) limit: soft (INF)(packets), hard (INF)(packets) expire add: soft 0(sec), hard 0(sec) expire use: soft 0(sec), hard 0(sec) lifetime current: 0(bytes), 0(packets) add 2012-10-31 13:42:08 use - tmpl src 25.239.33.30 dst 96.244.142.28 proto esp spi 0x00000000(0) reqid 0(0x00000000) mode tunnel level required share any enc-mask 00000000 auth-mask 00000000 comp-mask 00000000 src 0.0.0.0/0 dst 0.0.0.0/0 uid 0 dir 4 action allow index 28 priority 0 share any flag (0x00000000) lifetime config: limit: soft (INF)(bytes), hard (INF)(bytes) limit: soft (INF)(packets), hard (INF)(packets) expire add: soft 0(sec), hard 0(sec) expire use: soft 0(sec), hard 0(sec) lifetime current: 0(bytes), 0(packets) add 2012-10-31 13:42:04 use 2012-10-31 13:42:08 src 0.0.0.0/0 dst 0.0.0.0/0 uid 0 dir 3 action allow index 19 priority 0 share any flag (0x00000000) lifetime config: limit: soft (INF)(bytes), hard (INF)(bytes) limit: soft (INF)(packets), hard (INF)(packets) expire add: soft 0(sec), hard 0(sec) expire use: soft 0(sec), hard 0(sec) lifetime current: 0(bytes), 0(packets) add 2012-10-31 13:42:04 use 2012-10-31 13:42:08 src 0.0.0.0/0 dst 0.0.0.0/0 uid 0 dir 4 action allow index 12 priority 0 share any flag (0x00000000) lifetime config: limit: soft (INF)(bytes), hard (INF)(bytes) limit: soft (INF)(packets), hard (INF)(packets) expire add: soft 0(sec), hard 0(sec) expire use: soft 0(sec), hard 0(sec) lifetime current: 0(bytes), 0(packets) add 2012-10-31 13:42:04 use 2012-10-31 13:42:06 src 0.0.0.0/0 dst 0.0.0.0/0 uid 0 dir 3 action allow index 3 priority 0 share any flag (0x00000000) lifetime config: limit: soft (INF)(bytes), hard (INF)(bytes) limit: soft (INF)(packets), hard (INF)(packets) expire add: soft 0(sec), hard 0(sec) expire use: soft 0(sec), hard 0(sec) lifetime current: 0(bytes), 0(packets) add 2012-10-31 13:42:04 use 2012-10-31 13:42:07 Logs from charon: 00[DMN] Starting IKE charon daemon (strongSwan 5.0.0, Linux 3.3.4-5.fc17.x86_64, x86_64) 00[KNL] listening on interfaces: 00[KNL] em1 00[KNL] 96.244.142.28 00[KNL] fe80::224:e8ff:fed2:18b2 00[CFG] loading ca certificates from '/etc/strongswan/ipsec.d/cacerts' 00[CFG] loaded ca certificate "C=CH, O=strongSwan, CN=strongSwan CA" from '/etc/strongswan/ipsec.d/cacerts/caCert.pem' 00[CFG] loading aa certificates from '/etc/strongswan/ipsec.d/aacerts' 00[CFG] loading ocsp signer certificates from '/etc/strongswan/ipsec.d/ocspcerts' 00[CFG] loading attribute certificates from '/etc/strongswan/ipsec.d/acerts' 00[CFG] loading crls from '/etc/strongswan/ipsec.d/crls' 00[CFG] loading secrets from '/etc/strongswan/ipsec.secrets' 00[CFG] loaded RSA private key from '/etc/strongswan/ipsec.d/private/clientKey.pem' 00[CFG] loaded IKE secret for %any 00[CFG] loaded EAP secret for android 00[CFG] loaded EAP secret for android 00[DMN] loaded plugins: charon aes des sha1 sha2 md5 random nonce x509 revocation constraints pubkey pkcs1 pkcs8 pgp dnskey pem openssl fips-prf gmp xcbc cmac hmac attr kernel-netlink resolve socket-default stroke updown xauth-generic 08[NET] waiting for data on sockets 16[LIB] created thread 16 [15338] 16[JOB] started worker thread 16 11[CFG] received stroke: add connection 'android-hybrid' 11[CFG] conn android-hybrid 11[CFG] left=%any 11[CFG] leftsubnet=(null) 11[CFG] leftsourceip=(null) 11[CFG] leftauth=pubkey 11[CFG] leftauth2=(null) 11[CFG] leftid=(null) 11[CFG] leftid2=(null) 11[CFG] leftrsakey=(null) 11[CFG] leftcert=serverCert.pem 11[CFG] leftcert2=(null) 11[CFG] leftca=(null) 11[CFG] leftca2=(null) 11[CFG] leftgroups=(null) 11[CFG] leftupdown=ipsec _updown iptables 11[CFG] right=%any 11[CFG] rightsubnet=(null) 11[CFG] rightsourceip=96.244.142.3 11[CFG] rightauth=xauth 11[CFG] rightauth2=(null) 11[CFG] rightid=%any 11[CFG] rightid2=(null) 11[CFG] rightrsakey=(null) 11[CFG] rightcert=(null) 11[CFG] rightcert2=(null) 11[CFG] rightca=(null) 11[CFG] rightca2=(null) 11[CFG] rightgroups=(null) 11[CFG] rightupdown=(null) 11[CFG] eap_identity=(null) 11[CFG] aaa_identity=(null) 11[CFG] xauth_identity=(null) 11[CFG] ike=aes256-sha1-modp1024 11[CFG] esp=aes128-sha1-modp2048,3des-sha1-modp1536 11[CFG] dpddelay=30 11[CFG] dpdtimeout=150 11[CFG] dpdaction=0 11[CFG] closeaction=0 11[CFG] mediation=no 11[CFG] mediated_by=(null) 11[CFG] me_peerid=(null) 11[CFG] keyexchange=ikev1 11[KNL] getting interface name for %any 11[KNL] %any is not a local address 11[KNL] getting interface name for %any 11[KNL] %any is not a local address 11[CFG] left nor right host is our side, assuming left=local 11[CFG] loaded certificate "C=CH, O=strongSwan, CN=vpn.strongswan.org" from 'serverCert.pem' 11[CFG] id '%any' not confirmed by certificate, defaulting to 'C=CH, O=strongSwan, CN=vpn.strongswan.org' 11[CFG] added configuration 'android-hybrid' 11[CFG] adding virtual IP address pool 'android-hybrid': 96.244.142.3/32 13[CFG] received stroke: add connection 'android2' 13[CFG] conn android2 13[CFG] left=96.244.142.28 13[CFG] leftsubnet=0.0.0.0/0 13[CFG] leftsourceip=(null) 13[CFG] leftauth=pubkey 13[CFG] leftauth2=(null) 13[CFG] leftid=(null) 13[CFG] leftid2=(null) 13[CFG] leftrsakey=(null) 13[CFG] leftcert=serverCert.pem 13[CFG] leftcert2=(null) 13[CFG] leftca=(null) 13[CFG] leftca2=(null) 13[CFG] leftgroups=(null) 13[CFG] leftupdown=ipsec _updown iptables 13[CFG] right=%any 13[CFG] rightsubnet=10.0.0.0/24 13[CFG] rightsourceip=10.0.0.2 13[CFG] rightauth=pubkey 13[CFG] rightauth2=xauth 13[CFG] rightid=(null) 13[CFG] rightid2=(null) 13[CFG] rightrsakey=(null) 13[CFG] rightcert=clientCert.pem 13[CFG] rightcert2=(null) 13[CFG] rightca=(null) 13[CFG] rightca2=(null) 13[CFG] rightgroups=(null) 13[CFG] rightupdown=(null) 13[CFG] eap_identity=(null) 13[CFG] aaa_identity=(null) 13[CFG] xauth_identity=(null) 13[CFG] ike=aes256-sha1-modp1024 13[CFG] esp=aes128-sha1-modp2048,3des-sha1-modp1536 13[CFG] dpddelay=30 13[CFG] dpdtimeout=150 13[CFG] dpdaction=0 13[CFG] closeaction=0 13[CFG] mediation=no 13[CFG] mediated_by=(null) 13[CFG] me_peerid=(null) 13[CFG] keyexchange=ikev0 13[KNL] getting interface name for %any 13[KNL] %any is not a local address 13[KNL] getting interface name for 96.244.142.28 13[KNL] 96.244.142.28 is on interface em1 13[CFG] loaded certificate "C=CH, O=strongSwan, CN=vpn.strongswan.org" from 'serverCert.pem' 13[CFG] id '96.244.142.28' not confirmed by certificate, defaulting to 'C=CH, O=strongSwan, CN=vpn.strongswan.org' 13[CFG] loaded certificate "C=CH, O=strongSwan, CN=client" from 'clientCert.pem' 13[CFG] id '%any' not confirmed by certificate, defaulting to 'C=CH, O=strongSwan, CN=client' 13[CFG] added configuration 'android2' 13[CFG] adding virtual IP address pool 'android2': 10.0.0.2/32 08[NET] received packet: from 208.54.35.241[32235] to 96.244.142.28[500] 15[CFG] looking for an ike config for 96.244.142.28...208.54.35.241 15[CFG] candidate: %any...%any, prio 2 15[CFG] candidate: 96.244.142.28...%any, prio 5 15[CFG] found matching ike config: 96.244.142.28...%any with prio 5 01[JOB] next event in 29s 999ms, waiting 15[IKE] received NAT-T (RFC 3947) vendor ID 15[IKE] received draft-ietf-ipsec-nat-t-ike-02 vendor ID 15[IKE] received draft-ietf-ipsec-nat-t-ike-02\n vendor ID 15[IKE] received draft-ietf-ipsec-nat-t-ike-00 vendor ID 15[IKE] received XAuth vendor ID 15[IKE] received Cisco Unity vendor ID 15[IKE] received DPD vendor ID 15[IKE] 208.54.35.241 is initiating a Main Mode IKE_SA 15[IKE] IKE_SA (unnamed)[1] state change: CREATED => CONNECTING 15[CFG] selecting proposal: 15[CFG] proposal matches 15[CFG] received proposals: IKE:AES_CBC_256/HMAC_SHA1_96/PRF_HMAC_SHA1/MODP_1024, IKE:AES_CBC_256/HMAC_MD5_96/PRF_HMAC_MD5/MODP_1024, IKE:AES_CBC_128/HMAC_SHA1_96/PRF_HMAC_SHA1/MODP_1024, IKE:AES_CBC_128/HMAC_MD5_96/PRF_HMAC_MD5/MODP_1024, IKE:3DES_CBC/HMAC_SHA1_96/PRF_HMAC_SHA1/MODP_1024, IKE:3DES_CBC/HMAC_MD5_96/PRF_HMAC_MD5/MODP_1024, IKE:DES_CBC/HMAC_SHA1_96/PRF_HMAC_SHA1/MODP_1024, IKE:DES_CBC/HMAC_MD5_96/PRF_HMAC_MD5/MODP_1024 15[CFG] configured proposals: IKE:AES_CBC_256/HMAC_SHA1_96/PRF_HMAC_SHA1/MODP_1024, IKE:AES_CBC_128/AES_CBC_192/AES_CBC_256/3DES_CBC/CAMELLIA_CBC_128/CAMELLIA_CBC_192/CAMELLIA_CBC_256/HMAC_MD5_96/HMAC_SHA1_96/HMAC_SHA2_256_128/HMAC_SHA2_384_192/HMAC_SHA2_512_256/AES_XCBC_96/AES_CMAC_96/PRF_HMAC_MD5/PRF_HMAC_SHA1/PRF_HMAC_SHA2_256/PRF_HMAC_SHA2_384/PRF_HMAC_SHA2_512/PRF_AES128_XCBC/PRF_AES128_CMAC/MODP_2048/MODP_2048_224/MODP_2048_256/MODP_1536/MODP_4096/MODP_8192/MODP_1024/MODP_1024_160 15[CFG] selected proposal: IKE:AES_CBC_256/HMAC_SHA1_96/PRF_HMAC_SHA1/MODP_1024 15[NET] sending packet: from 96.244.142.28[500] to 208.54.35.241[32235] 04[NET] sending packet: from 96.244.142.28[500] to 208.54.35.241[32235] 15[MGR] checkin IKE_SA (unnamed)[1] 15[MGR] check-in of IKE_SA successful. 08[NET] received packet: from 208.54.35.241[32235] to 96.244.142.28[500] 08[NET] waiting for data on sockets 07[MGR] checkout IKE_SA by message 07[MGR] IKE_SA (unnamed)[1] successfully checked out 07[NET] received packet: from 208.54.35.241[32235] to 96.244.142.28[500] 07[LIB] size of DH secret exponent: 1023 bits 07[IKE] remote host is behind NAT 07[IKE] sending cert request for "C=CH, O=strongSwan, CN=strongSwan CA" 07[ENC] generating NAT_D_V1 payload finished 07[NET] sending packet: from 96.244.142.28[500] to 208.54.35.241[32235] 07[MGR] checkin IKE_SA (unnamed)[1] 07[MGR] check-in of IKE_SA successful. 04[NET] sending packet: from 96.244.142.28[500] to 208.54.35.241[32235] 08[NET] received packet: from 208.54.35.241[35595] to 96.244.142.28[4500] 10[IKE] ignoring certificate request without data 10[IKE] received end entity cert "C=CH, O=strongSwan, CN=client" 10[CFG] looking for XAuthInitRSA peer configs matching 96.244.142.28...208.54.35.241[C=CH, O=strongSwan, CN=client] 10[CFG] candidate "android-hybrid", match: 1/1/2/2 (me/other/ike/version) 10[CFG] candidate "android2", match: 1/20/5/1 (me/other/ike/version) 10[CFG] selected peer config "android2" 10[CFG] certificate "C=CH, O=strongSwan, CN=client" key: 2048 bit RSA 10[CFG] using trusted ca certificate "C=CH, O=strongSwan, CN=strongSwan CA" 10[CFG] checking certificate status of "C=CH, O=strongSwan, CN=client" 10[CFG] ocsp check skipped, no ocsp found 10[CFG] certificate status is not available 10[CFG] certificate "C=CH, O=strongSwan, CN=strongSwan CA" key: 2048 bit RSA 10[CFG] reached self-signed root ca with a path length of 0 10[CFG] using trusted certificate "C=CH, O=strongSwan, CN=client" 10[IKE] authentication of 'C=CH, O=strongSwan, CN=client' with RSA successful 10[ENC] added payload of type ID_V1 to message 10[ENC] added payload of type SIGNATURE_V1 to message 10[IKE] authentication of 'C=CH, O=strongSwan, CN=vpn.strongswan.org' (myself) successful 10[IKE] queueing XAUTH task 10[IKE] sending end entity cert "C=CH, O=strongSwan, CN=vpn.strongswan.org" 10[NET] sending packet: from 96.244.142.28[4500] to 208.54.35.241[35595] 04[NET] sending packet: from 96.244.142.28[4500] to 208.54.35.241[35595] 10[IKE] activating new tasks 10[IKE] activating XAUTH task 10[NET] sending packet: from 96.244.142.28[4500] to 208.54.35.241[35595] 04[NET] sending packet: from 96.244.142.28[4500] to 208.54.35.241[35595] 01[JOB] next event in 3s 999ms, waiting 10[MGR] checkin IKE_SA android2[1] 10[MGR] check-in of IKE_SA successful. 08[NET] received packet: from 208.54.35.241[35595] to 96.244.142.28[4500] 08[NET] waiting for data on sockets 12[MGR] checkout IKE_SA by message 12[MGR] IKE_SA android2[1] successfully checked out 12[NET] received packet: from 208.54.35.241[35595] to 96.244.142.28[4500] 12[MGR] checkin IKE_SA android2[1] 12[MGR] check-in of IKE_SA successful. 08[NET] received packet: from 208.54.35.241[35595] to 96.244.142.28[4500] 16[MGR] checkout IKE_SA by message 16[MGR] IKE_SA android2[1] successfully checked out 16[NET] received packet: from 208.54.35.241[35595] to 96.244.142.28[4500] 08[NET] waiting for data on sockets 16[IKE] XAuth authentication of 'android' successful 16[IKE] reinitiating already active tasks 16[IKE] XAUTH task 16[NET] sending packet: from 96.244.142.28[4500] to 208.54.35.241[35595] 04[NET] sending packet: from 96.244.142.28[4500] to 208.54.35.241[35595] 16[MGR] checkin IKE_SA android2[1] 01[JOB] next event in 3s 907ms, waiting 16[MGR] check-in of IKE_SA successful. 08[NET] received packet: from 208.54.35.241[35595] to 96.244.142.28[4500] 09[MGR] checkout IKE_SA by message 09[MGR] IKE_SA android2[1] successfully checked out 09[NET] received packet: from 208.54.35.241[35595] to 96.244.142.28[4500] .8rS 09[IKE] IKE_SA android2[1] established between 96.244.142.28[C=CH, O=strongSwan, CN=vpn.strongswan.org]...208.54.35.241[C=CH, O=strongSwan, CN=client] 09[IKE] IKE_SA android2[1] state change: CONNECTING => ESTABLISHED 09[IKE] scheduling reauthentication in 3409s 09[IKE] maximum IKE_SA lifetime 3589s 09[IKE] activating new tasks 09[IKE] nothing to initiate 09[MGR] checkin IKE_SA android2[1] 09[MGR] check-in of IKE_SA successful. 09[MGR] checkout IKE_SA 09[MGR] IKE_SA android2[1] successfully checked out 09[MGR] checkin IKE_SA android2[1] 09[MGR] check-in of IKE_SA successful. 01[JOB] next event in 3s 854ms, waiting 08[NET] waiting for data on sockets 08[NET] received packet: from 208.54.35.241[35595] to 96.244.142.28[4500] 14[MGR] checkout IKE_SA by message 14[MGR] IKE_SA android2[1] successfully checked out 14[NET] received packet: from 208.54.35.241[35595] to 96.244.142.28[4500] 14[IKE] processing INTERNAL_IP4_ADDRESS attribute 14[IKE] processing INTERNAL_IP4_NETMASK attribute 14[IKE] processing INTERNAL_IP4_DNS attribute 14[IKE] processing INTERNAL_IP4_NBNS attribute 14[IKE] processing UNITY_BANNER attribute 14[IKE] processing UNITY_DEF_DOMAIN attribute 14[IKE] processing UNITY_SPLITDNS_NAME attribute 14[IKE] processing UNITY_SPLIT_INCLUDE attribute 14[IKE] processing UNITY_LOCAL_LAN attribute 14[IKE] processing APPLICATION_VERSION attribute 14[IKE] peer requested virtual IP %any 14[CFG] assigning new lease to 'android' 14[IKE] assigning virtual IP 10.0.0.2 to peer 'android' 14[NET] sending packet: from 96.244.142.28[4500] to 208.54.35.241[35595] 14[MGR] checkin IKE_SA android2[1] 14[MGR] check-in of IKE_SA successful. 04[NET] sending packet: from 96.244.142.28[4500] to 208.54.35.241[35595] 08[NET] waiting for data on sockets 01[JOB] got event, queuing job for execution 01[JOB] next event in 91ms, waiting 13[MGR] checkout IKE_SA 13[MGR] IKE_SA android2[1] successfully checked out 13[MGR] checkin IKE_SA android2[1] 13[MGR] check-in of IKE_SA successful. 01[JOB] got event, queuing job for execution 01[JOB] next event in 24s 136ms, waiting 15[MGR] checkout IKE_SA 15[MGR] IKE_SA android2[1] successfully checked out 15[MGR] checkin IKE_SA android2[1] 15[MGR] check-in of IKE_SA successful.

    Read the article

  • unable to join domain using virtualbox

    - by FreshPrinceOfSO
    I'm in the process of setting up a VM environment for a MS certification exam (70-462). Following the training kit's instructions, I've set up a domain controller (DC) and two members (SQL-A, SQL-B) thus far. I can't figure out why I can't join the domain. DC IPv4 Address . . . : 10.10.10.10(Preferred) Subnet Mask. . . . : 255.0.0.0 DNS Servers. . . . : ::1 127.0.0.1 SQL-A IPv4 Address . . . : 10.10.10.20(Preferred) Subnet Mask. . . . : 255.0.0.0 DNS Servers. . . . : 10.10.10.10 SQL-B IPv4 Address . . . : 10.10.10.30(Preferred) Subnet Mask. . . . : 255.0.0.0 DNS Servers. . . . : 10.10.10.10 I've read how to do networking between virtual machines in virtualbox and the documentation. After trying various network adapter configurations, I can't get them to communicate in order to have the two members join the domain. When I ping from .30 to .10, I get: ping 10.10.10.10 Pinging 10.10.10.10 with 32 bytes of data: Reply from 10.10.10.20: Destination host unreachable. Reply from 10.10.10.20: Destination host unreachable. Reply from 10.10.10.20: Destination host unreachable. Reply from 10.10.10.20: Destination host unreachable. Trying to join the domain: netdom join SQL-A /domain:contso.com The specified domain either does not exist or could not be contacted. The command failed to complete successfully. Within VirtualBox, I've tried the following combinations for network adapter: Attached to - Promiscuous Mode ------------------------------- NAT Bridged Adapter - Deny Bridged Adapter - Allow VMs Bridged Adapter - Allow All Internal Network - Deny Internal Network - Allow VMs Internal Network - Allow All Host-only Adapter - Deny Host-only Adapter - Allow VMs Host-only Adapter - Allow All Edit ipconfig /all of DC ipconfig /all of SQL-A

    Read the article

  • WSUS is not using Akamai CDN for syncronisation source

    - by Geekman
    I've just installed a WSUS onto our network, and I'm currently doing the initial sync. I've found that WSUS does not seem to be talking to an Akamai cache, but rather with MS directly. This is contrary to what I've always thought regarding Windows Update traffic. Tcpdump of our WSUS server doing initial sync... As you can see it's speaking with 65.55.194.221. For me to speak to this IP, I have to go over international transit links. Which is of course not ideal. 8:42:31.279757 IP 65.55.194.221.https > XXXX.XXXX.XXXX.XXXX.50888: Flags [.], seq 4379374:4380834, ack 289611, win 256, length 1460 18:42:31.279759 IP 65.55.194.221.https > XXXX.XXXX.XXXX.XXXX.50888: Flags [.], seq 4380834:4382294, ack 289611, win 256, length 1460 18:42:31.279762 IP 65.55.194.221.https > XXXX.XXXX.XXXX.XXXX.50888: Flags [.], seq 4382294:4383754, ack 289611, win 256, length 1460 18:42:31.279764 IP 65.55.194.221.https > XXXX.XXXX.XXXX.XXXX.50888: Flags [P.], seq 4383754:4384144, ack 289611, win 256, length 390 18:42:31.279793 IP XXXX.XXXX.XXXX.XXXX.50888 > 65.55.194.221.https: Flags [.], ack 4369154, win 23884, length 0 18:42:31.279888 IP XXXX.XXXX.XXXX.XXXX.50888 > 65.55.194.221.https: Flags [.], ack 4377914, win 23884, length 0 18:42:31.280015 IP XXXX.XXXX.XXXX.XXXX.50888 > 65.55.194.221.https: Flags [.], ack 4384144, win 23884, length 0 And yet, if I ping download.windowsupdate.com it seems to resolve to a local (national) Akamai node, just fine: root@some-node:~# ping download.windowsupdate.com PING a26.ms.akamai.net (210.9.88.48) 56(84) bytes of data. 64 bytes from a210-9-88-48.deploy.akamaitechnologies.com (210.9.88.48): icmp_req=1 ttl=59 time=1.02 ms 64 bytes from a210-9-88-48.deploy.akamaitechnologies.com (210.9.88.48): icmp_req=2 ttl=59 time=1.10 ms Why is this? And how can I change that (if possible)? I know that I can manually specify a WSUS source to sync with instead of pick the default MS Update like I currently have... But it seems like I shouldn't have to do this. NOTE: I've haven't confirmed if a WUA speaks with Akamai, just looking at WSUS as all WUAs will use our internal WSUS from now on. We'll be looking to join an IX shortly with the hopes of peering with an Akamai cache and have very fast access to Windows Updates. Before I let this drive my motivations for an IX at all I want to first confirm it's actually possible for WSUS to speak with an Akamai cache. I know this is somewhat networking related, but I feel like it has more to do with WSUS than anything, so someone who knows WSUS better than me will likely be able to figure this out.

    Read the article

  • Suspected network performance issue on VirtualBox Ubuntu guest on Win7 host

    - by Adam
    I set up Ubuntu 12.04 in VirtualBox on the Win7 machine I was allocated on my new project. I am running Java, Eclipse, Tomcat to develop a large data-intensive application and I noticed that this application runs at half the speed of my colleague's identical machine, where he runs it all under Windows. I think I have narrowed down the performance issue to the network, after comparing and equalising all the Java VM settings with my colleague. Is there a ping test I can do or some other network diagnostic test to flag up any problems? To give some background, the network performance is confusing. Running a network speed test to my colleague's machine with iperf shows speeds of 6 Mb/s from my Ubuntu guest, and 90 Mb/s from the win7 host. Large downloads, e.g. the Java SDK, come down at about 1.2 MB/s on both the guest and the host. Pings are sub-1ms on the host, but 1.5ms on the guest. I also did a broadband speed test, and got 10Mb/s download speed on both, but the host has an upload speed of 10Mb/s but the guest only uploads at 3Mb/s. I've been trying to diagnose any MTU problems with ping -M do to identify any kind of packet fragmentation problem but it's progressing very slow because I don't have much experience in this area. From what I read on other people's networking issues with VB and Linux guests on Win7 hosts, I should be able to get the speed on the guest up to the same level as the host. I installed a fresh VM with Ubuntu again to see if I'd foobar'd it somehow, but I'm getting the same readings with iperf on the virgin installation. My setup is: Adapter 1: Intel PRO/1000 MT Desktop (NAT) Adapter 2: ditto (host-only adapter) eth0 Link encap:Ethernet HWaddr 08:00:27:0b:76:bf inet addr:10.0.2.15 Bcast:10.0.2.255 Mask:255.255.255.0 inet6 addr: fe80::a00:27ff:fe0b:76bf/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:86236 errors:0 dropped:0 overruns:0 frame:0 TX packets:49369 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:69163946 (69.1 MB) TX bytes:3530535 (3.5 MB) eth2 Link encap:Ethernet HWaddr 08:00:27:a3:26:b8 inet addr:192.168.56.101 Bcast:192.168.56.255 Mask:255.255.255.0 inet6 addr: fe80::a00:27ff:fea3:26b8/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:59 errors:0 dropped:0 overruns:0 frame:0 TX packets:57 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:9148 (9.1 KB) TX bytes:7648 (7.6 KB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:701 errors:0 dropped:0 overruns:0 frame:0 TX packets:701 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:66321 (66.3 KB) TX bytes:66321 (66.3 KB)

    Read the article

  • Virtualbox - routing subnet to bridge adapters

    - by user42384
    Hello, I have set up a Debian Lenny box with 3 vbox Lenny machines running eth0 of the host in bridged mode (on virtualbox 3.1.6). When testing in my local LAN, this all worked perfectly well and traffic flowed to and from the IPs of the virtual machines as it should. However, now that it's in its co-lo home, the networking setup is a bit different, and I'm unable to get traffic to flow to the vboxes properly. Specifically, the host has its own Primary IP, and I have a separate subnet of 8 (6 usable) IPs routed to the box for use by the vboxes. So, eth0 on host is: Machine IP: 2x.x.x.137 Gateway IP: 2x.x.x.138 Subnet Msk: 255.255.255.252 Subnet for vboxes is Subnet: 2x.x.x.240/29 Netmask: 255.255.255.248 vbox1 is configured to 2x.x.x.241 on eth0 as follows: auto eth0 iface eth0 inet static address 2x.x.x.241 netmask 255.255.255.248 Setting up a virtual interface (eth0:0) on the host with one of these subnet IPs allows me to ping to that address only from vbox1, and it allows me to ping vbox1 from the host. I can also ping that virtual interface perfectly well from outside, so the IPs are definitely landing at my machine. It seems I'm missing some sort of routing instruction either on the host or vbox1 to get traffic moving between the subnet and the default gateway, but I can't seem to figure out what it should be, or what glaringly obvious thing i'm missing. Most of my obvious attempts (the gw of eth0, the ip of eth0) were rejected by route command with SIOCADDRT: No such device (eg - i can't find it). I tried setting vbox1 to bridge on eth0:0, but this was not an acceptable device name and VBoxHeadless refused to start. The physical machine does have an unused physical NIC at eth1 that can be used if necessary for something or other. Host machine is running iptables configured by ferm, have experimented with it allowing forwarding for that subnet, but I wouldn't have thought this was necessary given the nature of the virtualbox devices (nor did it actually work). Clearing out all of these rules for a blank iptables set does not resolve the issue. (you can see ferm generated iptables at http://codedumper.com/ojaze) Thanks for any help you can give... Patrick

    Read the article

  • Windows 7 & Virtual PC and Internet (gateway) problems on host PC

    - by Mufasa
    I upgraded to Windows 7 on a PC that is a few years old. The CPU was one revision away from having Hyper-V on it. So, I had to install Microsoft Virtual PC 2007 (v6.0.156.0) to run full XP instances instead of the seamless XP virtualization that is advertised so much. That's fine though; the 'older' version is useful since I use it to run different versions of the whole XP/IE stack for testing. (I'm a web developer.) ...And for the one 16-bit application we still use at the office for scheduling. * sigh * The virtual instances work fine, including networking. My issue is that after a reboot or coming out of sleep mode, my host Windows 7 won't connect to the Internet. It will connect to the local network fine. If I disable the "Virtual Machine Network Services" item (I'll call "VMNS" from here on) in the LAN Connection properties box, it starts working. But than the Virtual PC instances lose their network connectivity. If I re-enable VMNS again in the same instance, everything works (Internet on host and in the virtualized instances). But after the next reboot/sleep cycle this starts over. The route table gave me a clue though. When doing a cycle w/ VMNS enabled: IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 On-link 10.0.3.51 20 0.0.0.0 0.0.0.0 10.0.10.10 10.0.3.51 276 ... After VMNS is disabled, the first route goes away. I assume that is for VMNS to intercept virtualized instance's network connections and forward them correctly? Just a guess though. More info: I checked my Firewall settings and Services (because I'm sort of a control nazi and turn off a lot) but couldn't find anything that made sense and if turned on changed anything. So it might be something there I'm missing, but I don't know what. My current hacked solution: So, I figured I'd mess with the routes myself to see if that helped, it did. If I run a route delete 0.0.0.0 on the universal (0.0.0.0) gateway routes, and add back in just the 2nd line with route add 0.0.0.0 mask 0.0.0.0 10.0.10.10--the one that points to my actual gateway (10.0.10.10)--then I don't have to mess with the disable/enable cycle of VMNS, and everything works. Running those two commands is faster then bringing up connection options and disabling and re-enabling VMNS, but I still don't want to have use that hack script every boot either. (Oh, and I also tried messing with hard-coding TCP/IP settings in my network adapter, including setting high metrics, etc., but that didn't help either.) Any suggestions on the right way to fix this?

    Read the article

  • Enabling DNS for IPv6 infrastructure

    After successful automatic distribution of IPv6 address information via DHCPv6 in your local network it might be time to start offering some more services. Usually, we would use host names in order to communicate with other machines instead of their bare IPv6 addresses. During the following paragraphs we are going to enable our own DNS name server with IPv6 address resolving. This is the third article in a series on IPv6 configuration: Configure IPv6 on your Linux system DHCPv6: Provide IPv6 information in your local network Enabling DNS for IPv6 infrastructure Accessing your web server via IPv6 Piece of advice: This is based on my findings on the internet while reading other people's helpful articles and going through a couple of man-pages on my local system. What's your name and your IPv6 address? $ sudo service bind9 status * bind9 is running If the service is not recognised, you have to install it first on your system. This is done very easy and quickly like so: $ sudo apt-get install bind9 Once again, there is no specialised package for IPv6. Just the regular application is good to go. But of course, it is necessary to enable IPv6 binding in the options. Let's fire up a text editor and modify the configuration file. $ sudo nano /etc/bind/named.conf.optionsacl iosnet {        127.0.0.1;        192.168.1.0/24;        ::1/128;        2001:db8:bad:a55::/64;};listen-on { iosnet; };listen-on-v6 { any; };allow-query { iosnet; };allow-transfer { iosnet; }; Most important directive is the listen-on-v6. This will enable your named to bind to your IPv6 addresses specified on your system. Easiest is to specify any as value, and named will bind to all available IPv6 addresses during start. More details and explanations are found in the man-pages of named.conf. Save the file and restart the named service. As usual, check your log files and correct your configuration in case of any logged error messages. Using the netstat command you can validate whether the service is running and to which IP and IPv6 addresses it is bound to, like so: $ sudo service bind9 restart $ sudo netstat -lnptu | grep "named\W*$"tcp        0      0 192.168.1.2:53        0.0.0.0:*               LISTEN      1734/named      tcp        0      0 127.0.0.1:53          0.0.0.0:*               LISTEN      1734/named      tcp6       0      0 :::53                 :::*                    LISTEN      1734/named      udp        0      0 192.168.1.2:53        0.0.0.0:*                           1734/named      udp        0      0 127.0.0.1:53          0.0.0.0:*                           1734/named      udp6       0      0 :::53                 :::*                                1734/named   Sweet! Okay, now it's about time to resolve host names and their assigned IPv6 addresses using our own DNS name server. $ host -t aaaa www.6bone.net 2001:db8:bad:a55::2Using domain server:Name: 2001:db8:bad:a55::2Address: 2001:db8:bad:a55::2#53Aliases: www.6bone.net is an alias for 6bone.net.6bone.net has IPv6 address 2001:5c0:1000:10::2 Alright, our newly configured BIND named is fully operational. Eventually, you might be more familiar with the dig command. Here is the same kind of IPv6 host name resolve but it will provide more details about that particular host as well as the domain in general. $ dig @2001:db8:bad:a55::2 www.6bone.net. AAAA More details on the Berkeley Internet Name Domain (bind) daemon and IPv6 are available in Chapter 22.1 of Peter Bieringer's HOWTO on IPv6. Setting up your own DNS zone Now, that we have an operational named in place, it's about time to implement and configure our own host names and IPv6 address resolving. The general approach is to create your own zone database below the bind folder and to add AAAA records for your hosts. In order to achieve this, we have to define the zone first in the configuration file named.conf.local. $ sudo nano /etc/bind/named.conf.local //// Do any local configuration here//zone "ios.mu" {        type master;        file "/etc/bind/zones/db.ios.mu";}; Here we specify the location of our zone database file. Next, we are going to create it and add our host names, our IP and our IPv6 addresses. $ sudo nano /etc/bind/zones/db.ios.mu $ORIGIN .$TTL 259200     ; 3 daysios.mu                  IN SOA  ios.mu. hostmaster.ios.mu. (                                2014031101 ; serial                                28800      ; refresh (8 hours)                                7200       ; retry (2 hours)                                604800     ; expire (1 week)                                86400      ; minimum (1 day)                                )                        NS      server.ios.mu.$ORIGIN ios.mu.server                  A       192.168.1.2server                  AAAA    2001:db8:bad:a55::2client1                 A       192.168.1.3client1                 AAAA    2001:db8:bad:a55::3client2                 A       192.168.1.4client2                 AAAA    2001:db8:bad:a55::4 With a couple of machines in place, it's time to reload that new configuration. Note: Each time you are going to change your zone databases you have to modify the serial information, too. Named loads the plain text zone definitions and converts them into an internal, indexed binary format to improve lookup performance. If you forget to change your serial then named will not use the new records from the text file but the indexed ones. Or you have to flush the index and force a reload of the zone. This can be done easily by either restarting the named: $ sudo service bind9 restart or by reloading the configuration file using the name server control utility - rndc: $ sudo rndc reconfig Check your log files for any error messages and whether the new zone database has been accepted. Next, we are going to resolve a host name trying to get its IPv6 address like so: $ host -t aaaa server.ios.mu. 2001:db8:bad:a55::2Using domain server:Name: 2001:db8:bad:a55::2Address: 2001:db8:bad:a55::2#53Aliases: server.ios.mu has IPv6 address 2001:db8:bad:a55::2 Looks good. Alternatively, you could have just ping'd the system as well using the ping6 command instead of the regular ping: $ ping6 serverPING server(2001:db8:bad:a55::2) 56 data bytes64 bytes from 2001:db8:bad:a55::2: icmp_seq=1 ttl=64 time=0.615 ms64 bytes from 2001:db8:bad:a55::2: icmp_seq=2 ttl=64 time=0.407 ms^C--- ios1 ping statistics ---2 packets transmitted, 2 received, 0% packet loss, time 1001msrtt min/avg/max/mdev = 0.407/0.511/0.615/0.104 ms That also looks promising to me. How about your configuration? Next, it might be interesting to extend the range of available services on the network. One essential service would be to have web sites at hand.

    Read the article

  • Client-Server Networking Between PHP Client and Java Server

    - by Muhammad Yasir
    Hi there, I have a university project which is already 99% completed. It consists of two parts-website (PHP) and desktop (Java). People have their accounts on the website and they wish to query different information regarding their accounts. They send an SMS which is received by desktop application which queries database of website (MySQL) and sends the reply accordingly. This part is working superbly. The problem is that some times website wishes to instruct the desktop application to send a specific SMS to a particular number. Apparently there seems no way other than putting all the load to the DB server... This is how I made it work. Website puts SMS jobs in a specific table. Java application polls this table again and again and if it finds a job, it executes it. Even this part is working correctly but unfortunately it is not acceptable by my university to poll the DB like this. :( The other approach I could think of is to use client-server one. I tried making Java server and its PHP client. So that whenever an SMS is to be sent, the website opens a socket connection to desktop application and sends two strings (cell # and SMS message). Unfortunately I am unable to do this. I was successfully to make a Java server which works fine when connected by a Java client, similarly my PHP client connects correctly to a PHP server, but when I try to cross them, they start hating each other... PHP shows no error but Java gives StreamCorruptedException when it tries to read header of input stream. Could someone please tell what I can try to make PHP client and Java server work together? Or if the said purpose can be achieved by another means, how? Regards, Yasir

    Read the article

  • How to find the filename of a script being run when it is executed from a symlink on linux

    - by Phil Boltt
    Hi, If I have a python script that is executed via a symlink, is there a way that I can find the path to the script rather than the symlink? I've tried using the methods suggested in this question, but they always return the path to the symlink, not the script. For example, when this is saved as my "/usr/home/philboltt/scripts/test.py" : #!/usr/bin/python import sys print sys.argv[0] print __file__ and I then create this symlink ln -s /usr/home/philboltt/scripts/test.py /usr/home/philboltt/test and execute the script using /usr/home/philboltt/test I get the following output: /usr/home/philboltt/test /usr/home/philboltt/test Thanks! Phil

    Read the article

  • How to emulate wireless in Virtualbox?

    - by huahsin68
    I have WinXP install in virtualbox which host in Linux. I have a TP-Link (TP-WN321G) USB wifi adapter and have the driver installed inside WinXP. When I plug-in the wifi adapter, there is an option show "Ralink 802.11g WLAN [0101]" in the virtualbox's USB icon, tick on that option, the Device Manager able to detect the hardware which shows TP-Link, but when look into the properties, it says there is no driver was install. I did try to install Ralink driver but still no luck. Just curious why my wifi adapter is TP-Link, but the option show Ralink? May I know how can I emulate the wireless network inside WindowsXP?

    Read the article

  • How do I add a broadcast IP to the loopback interface under os/x using ifconfig when my machine has no network?

    - by bandodeotarios
    I'm new to advanced network administration and I would like to do some testing with UDP broadcasting, so I need a broadcast address on my loopback interface. The machine is offline, in other words, there is no network. How can I accomplish that through ifconfig without having to buy a switch as one user in the comments suggested. In Linux all i have to do is use 127.255.255.255 and broadcasts work fine without any network or any switch. If I have a network i can just use 255.255.255.255, obviously.

    Read the article

  • Fedora 17 keeps using fedora 16 kernel

    - by MTilsted
    I did run preupgrade to upgrade my Fedora 16(x64) to Fedora 17. And it seemed to work fine. So I got the new gimp 2.8, gcc 4.7.0 and so on. But the system keeps using the old kernel from fc16. Uname -a gives me: Linux localhost.localdomain 3.3.6-3.fc16.x86_64 #1 SMP Wed May 16 21:43:01 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux The system downloaded the new kernel, so I got /boot/vmlinuz-3.3.7-1.fc17.x86_64 /boot/System.map-3.3.7-1.fc17.x86_64 /boot/initramfs-3.3.7-1.fc17.x86_64.img /boot/config-3.3.7-1.fc17.x86_64 But the system keeps using the old kernel from fc16. If i look at my /boot/grub2/grub.cfg file, it looks like this: # # DO NOT EDIT THIS FILE # # It is automatically generated by grub2-mkconfig using templates # from /etc/grub.d and settings from /etc/default/grub # ### BEGIN /etc/grub.d/00_header ### if [ -s $prefix/grubenv ]; then load_env fi set default="0" if [ "${prev_saved_entry}" ]; then set saved_entry="${prev_saved_entry}" save_env saved_entry set prev_saved_entry= save_env prev_saved_entry set boot_once=true fi function savedefault { if [ -z "${boot_once}" ]; then saved_entry="${chosen}" save_env saved_entry fi } function load_video { insmod vbe insmod vga insmod video_bochs insmod video_cirrus } set timeout=5 ### END /etc/grub.d/00_header ### ### BEGIN /etc/grub.d/10_linux ### menuentry 'Fedora (3.3.6-3.fc16.x86_64)' --class fedora --class gnu-linux --class gnu --class os { load_video set gfxpayload=keep insmod gzio insmod part_gpt insmod ext2 set root='(hd0,gpt2)' search --no-floppy --fs-uuid --set=root 3521a578-5829-4fb4-a485-8c097df77d07 echo 'Loading Fedora (3.3.6-3.fc16.x86_64)' linux /vmlinuz-3.3.6-3.fc16.x86_64 root=UUID=57459a16-97a0-46a4-8e71-cc3ec0ca4a3e ro KEYTABLE=dvorak rd.lvm=0 rd.dm=0 quiet SYSFONT=latarcyrheb-sun16 rhgb rd.md.uuid=60956781:734d95ba:424311e2:796702a7 rd.luks=0 LANG=en_US.UTF-8 echo 'Loading initial ramdisk ...' initrd /initramfs-3.3.6-3.fc16.x86_64.img } menuentry 'Fedora (3.3.5-2.fc16.x86_64)' --class fedora --class gnu-linux --class gnu --class os { load_video set gfxpayload=keep insmod gzio insmod part_gpt insmod ext2 set root='(hd0,gpt2)' search --no-floppy --fs-uuid --set=root 3521a578-5829-4fb4-a485-8c097df77d07 echo 'Loading Fedora (3.3.5-2.fc16.x86_64)' linux /vmlinuz-3.3.5-2.fc16.x86_64 root=UUID=57459a16-97a0-46a4-8e71-cc3ec0ca4a3e ro KEYTABLE=dvorak rd.lvm=0 rd.dm=0 quiet SYSFONT=latarcyrheb-sun16 rhgb rd.md.uuid=60956781:734d95ba:424311e2:796702a7 rd.luks=0 LANG=en_US.UTF-8 echo 'Loading initial ramdisk ...' initrd /initramfs-3.3.5-2.fc16.x86_64.img } ### END /etc/grub.d/10_linux ### ### BEGIN /etc/grub.d/20_linux_xen ### ### END /etc/grub.d/20_linux_xen ### ### BEGIN /etc/grub.d/30_os-prober ### ### END /etc/grub.d/30_os-prober ### ### BEGIN /etc/grub.d/40_custom ### # This file provides an easy way to add custom menu entries. Simply type the # menu entries you want to add after this comment. Be careful not to change # the 'exec tail' line above. ### END /etc/grub.d/40_custom ### ### BEGIN /etc/grub.d/41_custom ### if [ -f $prefix/custom.cfg ]; then source $prefix/custom.cfg; fi ### END /etc/grub.d/41_custom ### ### BEGIN /etc/grub.d/90_persistent ### ### END /etc/grub.d/90_persistent ### Anyone got a clue about why it still only references the fc16 kernel, and how I can upgrade it. My system is using raid1 on 2 disks, but /boot is not using raid. Mount for /boot is: /dev/sda2 on /boot type ext2 (rw,relatime,seclabel,user_xattr,acl,barrier=1) And / (The only other filesystem I have) is mounted as /dev/md0 on / type ext4 (rw,relatime,seclabel,user_xattr,acl,barrier=1,data=ordered)

    Read the article

  • What is the best/easiest way to use scripts to analyze network traffic?

    - by yungin
    I'm looking to analyze packets via scripts. I'd like to use something high level. I'm in a mac/linux environment. I'm currently looking at different python+libpcap libraries. Perhaps lua+wireshark too. Maybe tcpdump+bash (but not sure that has a lot of info i can use). I also heard good things about scapy. Not sure. I'm wondering if you have any recommendations? There's quite a few of them out there. What have you found that works best? I'd definitely want something scriptable not something that I need to compile (like c/c++, etc)

    Read the article

  • Ideas for networking project

    - by Chris Thompson
    Hi all, I'm a graduating senior in computer science taking a computer networks class and I'm trying to figure out my final project. I normally am not at a loss for ideas but be it senioritis or straight burn out, I've got nothing. I've done some fun stuff in the past, but I just can't seem to come up with a good idea. Given the mass of brilliance on this site, I figured it would be a good place to request some suggestions. To give you an idea of scope, it's due in about a month and I would consider myself proficient with mobile architectures like Android (although I have no iPhone experience) along with Java, C++, etc. If you can suggest an idea, I'd be happy to make it work in whatever language I know. Like I said, I'm a senior and will be graduating so I'd rather not take on something that would kill me... Also, I'd be happy to make it open source if it's an idea you'd always wanted to work on but didn't have the time to start. Thanks in advance for the help! Chris Edit 1: Thanks so much for the suggestions everyone! Unfortunately I've actually already written a chat client (for a network security class) and I think I'd run into some honor code issues if I did that again, although that's always a great option. I like the game idea and that's actually something I've never attempted before (in any capacity) although given that, I'm a little scared about time...

    Read the article

  • why gcc 4.x default reserve 8 bytes for stack on linux when calling a method?

    - by nikcname
    as a beginner of asm, I am checking gcc -S generated asm code to learn. why gcc 4.x default reserve 8 bytes for stack when calling a method? func18 is the empty function with no return no param no local var defined. I can't figure out why 8 bytes is reserved here (neither any forum/site mention for the reason, ppl seems take it for granted) is it for the %ebp just push? or return type?! many thx! .globl _func18 _func18: pushl %ebp movl %esp, %ebp subl $8, %esp .text

    Read the article

  • why gcc 4.x default reserve 8 bytes for stack on linux when calling a method?

    - by nikcname
    as a beginner of asm, I am checking gcc -S generated asm code to learn. why gcc 4.x default reserve 8 bytes for stack when calling a method? func18 is the empty function with no return no param no local var defined. I can't figure out why 8 bytes is reserved here (neither any forum/site mention for the reason, ppl seems take it for granted) is it for the %ebp just push? or return type?! many thx! .globl _func18 _func18: pushl %ebp movl %esp, %ebp subl $8, %esp .text

    Read the article

  • Good C# Networking Book

    - by Dan
    Hey guys I am looking for a good solid introduction book to the fundementals of network programming in C#. For example is have looked at this one http://www.amazon.com/C-Network-Programming-Richard-Blum/dp/0782141765/ref=pd_sim_b_5 but it is quite old now. Anyone used one recently, i would greatly appriciate it thanks dan

    Read the article

  • Any way to stop VMWare workstation from dropping SSH connections?

    - by oljones
    I have VMWare workstation 8 with a few Linux guests. I have had problems maintaining an active SSH connection to my VMs when they are in bridged mode. I first read that the onboard realtek network cards were not well supported so I bought a Intel Pro/1000 GT card. This supposedly had support. But this made no difference. Connections via SSH are active for about the first 3 minutes then hang and die. I have changed the TCP Checksum offload on the Intel and Realtek NICs, but this only works some of the time and even then not for very long. The best I could do was about 20 minutes before the connection was dropped. Any ideas?

    Read the article

< Previous Page | 259 260 261 262 263 264 265 266 267 268 269 270  | Next Page >