Search Results

Search found 12325 results on 493 pages for 'remote execution'.

Page 264/493 | < Previous Page | 260 261 262 263 264 265 266 267 268 269 270 271  | Next Page >

• Why won't USB 3.0 external hard drive run at USB 3.0 speeds?

  - by jgottula

  I recently purchased a PCI Express x1 USB 3.0 controller card (containing the NEC USB 3.0 controller) with the intent of using a USB 3.0 external hard drive with my Linux box. I installed the card in an empty PCIe slot on my motherboard, connected the card to a power cable, strung a USB 3.0 cable between one of the new ports and my external HDD, and connected the HDD to a wall socket for power. Booting the system, the drive works 100% as intended, with the one exception of throughput: rather than using SuperSpeed 4.8 Gbps connectivity, it seems to be falling back to High Speed 480 Mbps USB 2.0-style throughput. Disk Utility shows it as a 480 Mbps device, and running a couple Disk Utility and dd benchmarks confirms that the drive fails to exceed ~40 MB/s (the approximate limit of USB 2.0), despite it being an SSD capable of far more than that. When I connect my USB 3.0 HDD, dmesg shows this: [ 3923.280018] usb 3-2: new high speed USB device using ehci_hcd and address 6 where I would expect to find this: [ 3923.280018] usb 3-2: new SuperSpeed USB device using xhci_hcd and address 6 My system was running on kernel 2.6.35-25-generic at the time. Then, I stumbled upon this forum thread by an individual who found that a bug, which was present in kernels prior to 2.6.37-rc5, could be the culprit for this type of problem. Consequently, I installed the 2.6.37-generic mainline Ubuntu kernel to determine if the problem would go away. It didn't, so I tried 2.6.38-rc3-generic, and even the 2.6.38 nightly from 2010.02.01, to no avail. In short, I'm trying to determine why, with USB 3.0 support in the kernel, my USB 3.0 drive fails to run at full SuperSpeed throughput. See the comments under this question for additional details. Output that might be relevant to the problem (when booting from 2.6.38-rc3): Relevant lines from dmesg: [ 19.589491] xhci_hcd 0000:03:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 19.589512] xhci_hcd 0000:03:00.0: setting latency timer to 64 [ 19.589516] xhci_hcd 0000:03:00.0: xHCI Host Controller [ 19.589623] xhci_hcd 0000:03:00.0: new USB bus registered, assigned bus number 12 [ 19.650492] xhci_hcd 0000:03:00.0: irq 17, io mem 0xf8100000 [ 19.650556] xhci_hcd 0000:03:00.0: irq 47 for MSI/MSI-X [ 19.650560] xhci_hcd 0000:03:00.0: irq 48 for MSI/MSI-X [ 19.650563] xhci_hcd 0000:03:00.0: irq 49 for MSI/MSI-X [ 19.653946] xHCI xhci_add_endpoint called for root hub [ 19.653948] xHCI xhci_check_bandwidth called for root hub Relevant section of sudo lspci -v: 03:00.0 USB Controller: NEC Corporation uPD720200 USB 3.0 Host Controller (rev 03) (prog-if 30) Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at f8100000 (64-bit, non-prefetchable) [size=8K] Capabilities: [50] Power Management version 3 Capabilities: [70] MSI: Enable- Count=1/8 Maskable- 64bit+ Capabilities: [90] MSI-X: Enable+ Count=8 Masked- Capabilities: [a0] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting Capabilities: [140] Device Serial Number ff-ff-ff-ff-ff-ff-ff-ff Capabilities: [150] #18 Kernel driver in use: xhci_hcd Kernel modules: xhci-hcd Relevant section of sudo lsusb -v: Bus 012 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 3.00 bDeviceClass 9 Hub bDeviceSubClass 0 Unused bDeviceProtocol 3 bMaxPacketSize0 9 idVendor 0x1d6b Linux Foundation idProduct 0x0003 3.0 root hub bcdDevice 2.06 iManufacturer 3 Linux 2.6.38-020638rc3-generic xhci_hcd iProduct 2 xHCI Host Controller iSerial 1 0000:03:00.0 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 25 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xe0 Self Powered Remote Wakeup MaxPower 0mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 9 Hub bInterfaceSubClass 0 Unused bInterfaceProtocol 0 Full speed (or root) hub iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0004 1x 4 bytes bInterval 12 Hub Descriptor: bLength 9 bDescriptorType 41 nNbrPorts 4 wHubCharacteristic 0x0009 Per-port power switching Per-port overcurrent protection TT think time 8 FS bits bPwrOn2PwrGood 10 * 2 milli seconds bHubContrCurrent 0 milli Ampere DeviceRemovable 0x00 PortPwrCtrlMask 0xff Hub Port Status: Port 1: 0000.0100 power Port 2: 0000.0100 power Port 3: 0000.0100 power Port 4: 0000.0100 power Device Status: 0x0003 Self Powered Remote Wakeup Enabled Full, non-verbose lsusb: Bus 012 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 011 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 010 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 009 Device 003: ID 04d9:0702 Holtek Semiconductor, Inc. Bus 009 Device 002: ID 046d:c068 Logitech, Inc. G500 Laser Mouse Bus 009 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 006: ID 174c:5106 ASMedia Technology Inc. Bus 003 Device 004: ID 0bda:0151 Realtek Semiconductor Corp. Mass Storage Device (Multicard Reader) Bus 003 Device 002: ID 058f:6366 Alcor Micro Corp. Multi Flash Reader Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 006: ID 1687:0163 Kingmax Digital Inc. Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 002: ID 046d:081b Logitech, Inc. Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Full output: full dmesg full lspci full lsusb

  Read the article

• JCP.Next Progress Updates

  - by heathervc

  JSR 355, JCP Executive Committee Merge, is currently nearing the end of the Public Review period.  Review the current draft here and provide feedback here.  The review closes on 12 June 2012.  The JCP Executive Committee met face to face in Sao Paulo, Brazil earlier in May, and has published a revision (version 2.1) of the EC Standing Rules.  The EC Standing Rules were introduced in October 2011 with the launch of JCP version 2.8 (JSR 348).  Version 2.1 of the EC Standing Rules will modify rules for attendance at EC face-to-face meetings. Remote observers will be permitted in "read-only" mode but unless a member attends in person they will be counted as absent.  The review period for these changes will close on June 30 2012.  Please comment on the proposed changes by logging an issue in the JCP EC issue tracker.

  Read the article

• Is it possible to auto-mount sshfs

  - by Mark D

  Is it possible to auto-mount a remote FS using sshfs upon instantiating a proper VPN connection? Allow me to explain the scenario, I'm working remotely, to do that it helps if I can mount my home dir from a server in the office. To do that I need to vpn in. So within network manager I select the relevant VPN and connect. It connects but now I have to drop to the command line and mount my home dir on several machines. If I forget to do one machine my local dev environment isn't as efficient. I suppose I could write a quick bash script to do this but I'd rather get it running automatically when I connect.

  Read the article

• Advice on how to understand in general and in practice IT Infrastructure

  - by Luca

  My IT knowledge resides mainly in SW development. I have just some basic know how about networks. On the net I tried to get information and read books in order to better understand the overall IT infrastrcuture, but all the sources I found are too generic or, mainly, too detailed in just one aspect, making me lost. Could anyone suggest some books or web resources as good compromise in details? My goal would be able to understand the network issues and security threats when, for example, two remote system have to be setup and put in connection each other. Considering this scenario there are several aspects to consider: firewalls, intranet/internet interconnections, certificates for httpS, etc. The argument is quite wide, therefore I was looking for something that might help to start to understand this subject without going too deep in details (Computer Networks from A.Tanenbaum is a wonderful milestone, but way too specific for my scope). Thanks

  Read the article

• New Oracle Cloud support in OEPE

  - by gstachni

  Oracle Enterprise Pack for Eclipse 12c (12.1.1.1.1) includes updated support for development with the Java Cloud Service. Users can now do iterative development against their Java Cloud Service instance in addition to testing against local and remote WebLogic Server installations. Some details of the cloud tools are below: Templates and wizards to create projects and server configurations for Oracle Java Cloud Service Develop applications to run and deploy to the cloud, including Oracle ADF. Check cloud server runtime and deployment logs in new log analyzers Test applications before deployment with integrated whitelist scans. Whitelist tools support as-you-type validation, project build validation, and on demand scans to highlight coding violations. Errors are reported in application source, the Problems view, and a new Whitelist violations view. Access the Oracle Public Cloud administrative consoles directly from within Eclipse.

  Read the article

• Keyboard shorcut for a custom folder in Desktop

  - by palerdot

  I would like to configure a keyboard shortcut for a particular folder in my Desktop. I will be using this folder quite often and is there a way to open them with a custom keyboard shortcut ? The remote thing I came across regarding this is this question which is for opening home folder similar to Windows, but I do not want to go to home folder and navigate from there all the way to a folder in the Desktop (mouse clicking the desktop folder is way too easier than this method). So my Question: Can I have custom keyboard shortcuts for custom folders like folders in Desktop ? I'm using 12.04.

  Read the article

• DesktopCouch does not sync

  - by burli

  I have here two computers, both installed with Ubuntu 10.10. The Laptop uses the Netbook Edition. Both are connected, file sync and Tomboy Notes are working. My Desktop syncs databases with Ubuntu One, my Laptop does not. If I delete for example the contacts Database on my Desktop, the database is back a view seconds later. If I delete the same database on my laptop, nothing happens. (I'm using Futon) If I kill beam, delete the config and try to restart with the dbus-send I got an error Error org.freedesktop.DBus.Error.NoReply: Did not receive a reply. Possible causes include: the remote application did not send a reply, the message bus security policy blocked the reply, the reply timeout expired, or the network connection was broken. How can I fix that?

  Read the article

• Error : Could not display "obex://" when paired with a Nokia 3110c

  - by MobileDev123

  Hi, I have paired my nokia 3110c via bt on my pc, I can receive a file from my pc to the phone, but I can not browse the contents of phone from my computer. Here is the error message Error: Did not receive a reply. Possible causes include: the remote application did not send a reply, the message bus security policy blocked the reply, the reply timeout expired, or the network connection was broken. Please select another viewer and try again. How can I transfer contents from my phone to my computer?

  Read the article

• Can I do a git merge entirely remotely?

  - by CaptainAwesomePants

  My team shares a "work" branch and a "stable" branch. Whenever a particular work branch is approved for further testing/release/etc, we merge it into stable. No code is ever checked directly into the stable branch. Because of this, merge conflicts simply won't happen, and it seems silly to pull down the work branch and the stable branch, merge them, and then push the changes back. Is there a git command to ask a remote git server to commit a merge of two branches that it already knows about?

  Read the article

• Redirect public traffic to a different subfolder, while local traffic remains unchanged

  - by ecnepsnai

  I would like to have local (intranet) HTTP traffic go to the /var/www/html folder while any public traffic goes to the subfolder, /var/www/html/public I've tried this configuration, with some variation, in httpd.conf <VirtualHost PRIVATE-IP> DocumentRoot /var/www/html ServerName ecn ErrorLog /var/www/logs/error/private CustomLog /var/www/logs/access/private common </VirtualHost> <VirtualHost PUBLIC-IP> DocumentRoot /var/www/html/public ServerName PUBLIC-DOMAIN-NAME ErrorLog /var/www/logs/error/public CustomLog /var/www/logs/access/public common </VirtualHost> PUBLIC-IP, PRIVATE-IP, and PUBLIC-DOMAIN name are all replaced with the correct values in the actual document. The problem is, local traffic can browse fine but remote traffic is directed to the root folder and getting 403d (because I have that folder blocked off through my .htaccess file). If I append /public to the URL it works fine.

  Read the article

• Setting up a GUI-based libvirt VM

  - by LibertasMens

  I am attempting to create a virtual machine using libvirt that will have a GNOME GUI and remote accessibility. I have successfully set up the VM to run, but I am unable to access it remotely. The command issued to build the VM: sudo vmbuilder kvm ubuntu --suite=precise --flavour=generic --arch=amd64 --mirror=http://de.archive.ubuntu.com/ubuntu -o --libvirt=qemu:///system --part=/usr/xxxx/vmbuilder.partition --templates=/usr/xxxx/mytemplates --addpkg=nano --addpkg=unattended-upgrades --addpkg=acpid --firstboot=/usr/xxxx/boot.sh --cpus=2 --mem=4096--user=xxxx --name=xxxx --pass=xxxx --hostname=xxxx --bridge=br0 My intent is to have a virtual machine that my client can remotely access with a GUI.

  Read the article

• What set of tools make up "the rails way" of testing javascript in the browser?

  - by Jordan Feldstein

  What's the concensus for doing in-browser (either headless or remote-controlled) testing of javascript? Unit testing my JS is nice, but can't protect against irresponsible changes to the DOM. Unit testing of the JS and functional testing of the views to make sure they both provide and utilize the same, correct DOM, might work, but then the link between JS and DOM is being covered in two places which seems brittle or cumbersome. Is there an acknowledged "Rails Way" to implement full-stack tests, where I can run my javascript against the DOM rendered by the rest of the app, and check the results? (Something like what PHPUnit and Selenium give us, but inside the rails framework?)

  Read the article

• How to set up a mail server on Linux only for sending admin/debug emails?

  - by ChocoDeveloper

  I need to send server reports to myself from my remote servers, and I don't mind them going to spam, so I don't need SPF, DKIM, etc. I tried using mailutils to send something like this: uptime | mail -s "uptime" [email protected], but the emails don't go through. In /var/mail/root I received a message saying the HELO was invalid. So then I tried also adding -r root@my-ip, and now I don't get any error messages but I don't receive the email either. How can I do this?

  Read the article

• Regulating outgoing traffic on ubuntu VM

  - by DazSlayer

  I am making a virtual network setup for my high school cybersecurity team to practice. I am connecting all the VMs together through a VPN and then people who are practicing will VPN in and ssh/remote desktop into the different VMs. The problem is that for practicing, they will need root access into the VMs and because the VMs are connecting to my personal network, the VMs pose a security risk to my personal network. Is there any way in either VMWare or VirtualBox or even making an unchangeable iptable (I can make all the windows VMs go thru a linux VM) to prevent people from connecting to my local network via the VM?

  Read the article

• bluetooth between ubuntu 10.10 and nokia error : Could not display "obex://"

  - by MobileDev123

  Hi, I have paired my nokia 3110c via bt on my pc, I can receive a file from my pc to the phone, but I can not browse the contents of phone from my computer. Here is the error message Error: Did not receive a reply. Possible causes include: the remote application did not send a reply, the message bus security policy blocked the reply, the reply timeout expired, or the network connection was broken. Please select another viewer and try again. How can I transfer contents from my phone to my computer?

  Read the article

• When failure is a feature

  Warning: this post is going to be slightly off-topic and non-technical. Well, not computer science technical at least. I was reading an article in SciAm this morning about the possibility of a robot uprising. Dont laugh yet, this is a very real, if still quite remote possibility. The main idea that was described was that AI could rise one day to self-awareness and to an ability to improve itself through self-replication beyond human abilities to control it. Sure, thats one possibility, and some...Did you know that DotNetSlackers also publishes .net articles written by top known .net Authors? We already have over 80 articles in several categories including Silverlight. Take a look: here.

  Read the article

• backup dedicated server runing ubuntu 10.04 and plesk 11.01 prior to update os to uduntu 12.04

  - by timmob

  i would like to backup my dedicated server which is my web server hosting various sites and email, so that I can update the os to Ubuntu 12.04, and basically restore back to 10.04 if things go wrong. I have a local machine that I can install 12.04 onto an then I was going to rsinc between the two, but I am fairly clueless when it comes to linux. I can ssh into the remote server and gain root access. can anyone explain if i need to backup the whole server hard drive or just some of the files? Thanks Timmo.

  Read the article

• "Google files": Building a web interface to find/ack/grep

  - by user27915816

  I am working on a project where we would like to have build a web interface that gives the user the ability to "Google" files in a directory in a remote machine. For example, the user would type a string in a box, and then the system would find all files that contain that string and present them in the browser. The system would then give the user the ability click on any of the files to open them/display them in the browser. We want to avoid reinventing the wheel if possible, but don't really know where to start (none of us in the team have much experience building websites). What software packages, libraries or tools exist that can help us get this done?

  Read the article

• Cloud consolidation handling multi databases

  - by llaszews

  I have spoken about virtualization and the different types of virtualization. Which includes OS zones, application server domains, database schemas, VLANS and other approaches. Another approach is to create a virtually federated database in the cloud. DBSpaces is a company that has a technology to created a virtually federated database in the cloud. DBSpaces is a Virtual Database technology that allows an organisation thru a single Virtual Database access multiple data sources (or database spaces) in real-time. Additionally dbSpaces can be configured to access an organisations data internally using a remote gateway so that their dbSpace is seamless across the Public and Private cloud.

  Read the article

• How to execute? [closed]

  - by Viswa

  Possible Duplicate: how to read the password from variable? I did the below code in my python script,but its not work. #! /usr/bin/python import os address = "rsync -avrz [email protected]:/opt/script/python/data/ /opt/script/python/data/" passwd ="my server password" os.system('%(address)s "echo %(passwd)s"' %locals()) it throws below error. If arg is a remote file/dir, prefix it with a colon (:). rsync error: syntax or usage error (code 1) at main.c(1236) [Receiver=3.0.7] If i run os.system('%(address)s' %locals()) means it work without any error but it ask password. I need that password should be read from my passwd variable. How to write python script to read server password from my variable.

  Read the article

• Move window from display :0.0 to display :10.0?

  - by fabyouless

  I'm using Cygwin to login to my lubuntu box: ssh -y *user*@192.168.12.37 I can easily use byobu to redeem my cli session. Is there a way to move a running window from display :0.0 to my remote session (:10.0)? I ask because my lubuntu box is hooked to the HDTV in the living room, and I give my kids priority to do their educational stuff on the big screen. I then (try to) pick up where I left off on a netbook Cygwin session. Usually I have to quit everything and restart on the netbook.

  Read the article

• Chrome Mobile: The Mobile Web Developers Toolkit (Part 2)

  Chrome Mobile: The Mobile Web Developers Toolkit (Part 2) Building for mobile web requires a different mindset than desktop web development, and a different set of tools. The tools we're used to using often aren't available or would take up too much screen real estate. And going back to the dark ages of tweak/save/deploy/test/repeat isn't exactly optimal, so what can we do? Thankfully there are a number of great options - from remote debugging to emulation, mobile browsers are offering more and more tools to make our lives easier. We'll take a look at a couple of tools that you can use today to make cross platform mobile web development easier and then peer into the crystal ball to see what tools may bring in the future. Join us for Part 2 - as we take a look at a some of the many tools to make testing the mobile web easier. From: GoogleDevelopers Views: 0 0 ratings Time: 01:00:00 More in Science & Technology

  Read the article

• After Upgrade from 13.04 to 13.10 missing user in login screen

  - by Mark

  I have upgraded to 13.10 from 13.04 now after booting (even after updates and rebooting) my user id is not listed. It has a uid higher than the minimum in lightdm.conf. I have the user light display manager , guest , and remote login options in the login screen but not my ususal user id that I have been using from ubuntu 9 something. It is a normal user and an administrator so that I could authorize drivers, updates, etc... I do not have any custom display manager setup. It has been standard unity since unity was available. I can login to my account by logging in as guest opening a termial and using su - user Any insight would be appreciated. Thanks

  Read the article

• Chrome Mobile: The Mobile Web Developers Toolkit (Part 1)

  Chrome Mobile: The Mobile Web Developers Toolkit (Part 1) Building for mobile web requires a different mindset than desktop web development, and a different set of tools. The tools we're used to using often aren't available or would take up too much screen real estate. And going back to the dark ages of tweak/save/deploy/test/repeat isn't exactly optimal, so what can we do? Thankfully there are a number of great options - from remote debugging to emulation, mobile browsers are offering more and more tools to make our lives easier. We'll take a look at a couple of tools that you can use today to make cross platform mobile web development easier and then peer into the crystal ball to see what tools may bring in the future. Join us for Part 1 - as we take a look at a few boiler plates, frameworks and helpful libraries for building the mobile web. From: GoogleDevelopers Views: 0 0 ratings Time: 01:00:00 More in Science & Technology

  Read the article

• Ubuntu VPN server setup

  - by framberries

  I followed the instructions that the answer on this thread gave, Easiest way to setup Ubuntu as a VPN server. However, I cannot get it to work. When I try to connect to my network, it just says the server cannot be reached. I setup the remote IP options (which I uncommented) to be 10.0.2.2-100. My router serves out 10.0.1.2-250. I also have users setup, but they are uncommented as well. I assume you need to uncomment them?

  Read the article

< Previous Page | 260 261 262 263 264 265 266 267 268 269 270 271  | Next Page >