Search Results

Search found 8314 results on 333 pages for 'ug events'.

Page 265/333 | < Previous Page | 261 262 263 264 265 266 267 268 269 270 271 272  | Next Page >

• SharePoint Records Center Submitted E-mail Records not picked up

  - by Kenneth Verburg

  We have set up a new SharePoint 2007 site with a Records Repository. We're using Exchange 2007 Managed Folders to route e-mails to this repository based on the 'label' attached to the e-mail as set in the Exchange 2007 journaling options. E-mails added to a Managed Folder get sent to SharePoint, they end up in the "Submitted E-mail Records" list of the Records Repository. That's according to plan, but the e-mails are not routed to the respective document library as defined by the label. Instead an error appears in the event viewer for every e-mail listed in the Submitted E-mail Records list, on every interval of the records repository schedule (set to every two minutes for testing purposes): Value cannot be null, parameter name: g. Sending a document from the SharePoint site iself to the Records Repository via the Send To... link works fine, but e-mails get stuck in the list... We have set Document Libraries in the Respository with and without content types (with matching names with the Label and the Record Routing rule set). Any ideas what could be wrong? This is in the event log: Every two minutes the following error appears in the Application Log: Source: Office SharePoint Server Category: Records Center Type: Error Event ID: 4975 User: N/A Computer: SPS2007 Description: Value cannot be null. Parameter name: g For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp.

  Read the article

• Does a 3ware "ECC-ERROR" matter on a JBOD when I have ZFS?

  - by Stefan Lasiewski

  I have a FreeBSD 8.x machine running ZFS and with a 3ware 9690SA controller. The 3ware controller shows an ECC-ERROR with one of the disks: //host> /c0 show VPort Status Unit Size Type Phy Encl-Slot Model ------------------------------------------------------------------------------ p0 OK u0 279.39 GB SAS 0 - SEAGATE ST3300657SS p1 OK u0 279.39 GB SAS 1 - SEAGATE ST3300657SS p2 OK u1 931.51 GB SAS 2 - SEAGATE ST31000640SS p3 ECC-ERROR u2 931.51 GB SAS 3 - SEAGATE ST31000640SS p4 OK u3 931.51 GB SAS 4 - SEAGATE ST31000640SS /c0 show events shows no ECC errors in it's recent history. ZFS does not currently detect any errors. zpool status says No known data errors My question: Is this ECC-ERROR something that I need to be concerned about? According to the 3ware CLI 9.5.2 Manual, an ECC-ERROR means that the 3ware controller caught a read-error for one or more sectors on this drive. This sometimes occurs when a RAID array is recovering from a failed disk. I believe that ECC-ERRORS can also be detected when the 3ware Controller verifies each disk. None of the drives have failed and thus there was no drive rebuild, so I assume that 3ware discovered a bad sector when it ran it's weekly auto-verify scan of the disks. Is this a safe assumption? According to our logs, ZFS has not detected any bad sectors on this drive. ZFS can work around read errors -- if ZFS detects a bad sector on the drive, it will simply mark that sector as bad and never use it again. From the ZFS perspective one bad sector isn't a big deal, although it might indicate that the drive is starting to go bad.

  Read the article

• Issue with InnoDB engine while enabling and [ skip-innodb ] - [ERROR] Plugin 'InnoDB' init function returned error

  - by Ahn

  How to enable InnoDB, which was previously disabled with skip-innodb option. Case 1: Disabled the innodb with skip-innodb option and show engines givens as below. Engine | Support ... | InnoDB | NO ...... Case 2: As I want to enable the innodb, I commanded the #skip-innodb option and restarted. But now the show engines even not showing the InnoDB engine in the list. ? Mysql Version : 5.1.57-community-log OS : CentOS release 5.7 (Final) Log: 120622 13:06:36 InnoDB: Initializing buffer pool, size = 8.0M 120622 13:06:36 InnoDB: Completed initialization of buffer pool InnoDB: No valid checkpoint found. InnoDB: If this error appears when you are creating an InnoDB database, InnoDB: the problem may be that during an earlier attempt you managed InnoDB: to create the InnoDB data files, but log file creation failed. InnoDB: If that is the case, please refer to InnoDB: http://dev.mysql.com/doc/refman/5.1/en/error-creating-innodb.html 120622 13:06:36 [ERROR] Plugin 'InnoDB' init function returned error. 120622 13:06:36 [ERROR] Plugin 'InnoDB' registration as a STORAGE ENGINE failed. 120622 13:06:36 [Note] Event Scheduler: Loaded 0 events 120622 13:06:36 [Note] /usr/sbin/mysqld: ready for connections. Version: '5.1.57-community-log' socket: '/data/mysqlsnd/mysql.sock1' port: 3307 MySQL Community Server (GPL)

  Read the article

• Ubuntu 10.04 server delay responding to AJAX requests

  - by DanielAttard

  I manage a Ubuntu 10.04 server with a couple of domains hosted on it. As I continue to learn more about all these wonderful new (for me), one issue that I have begun to notice is the delay it sometimes takes for the server to respond to certain requests. As an example, when I view the timeline of events using firebug I can see that most of the time when I make a POST, the server responds in under 100ms. Sometimes, however, there is a substantial delay before the RESPONSE from the server. I can't seem to tell when the delay will happen and when it won't, however, when it happens the delay is always for about 4.5 seconds. The delay seems to happen about 30-40% of the time. Here is the section of apache2.conf dealing with logs: # # The following directives define some format nicknames for use with # a CustomLog directive (see below). # If you are behind a reverse proxy, you might want to change %h into %{X-Forwarded-For}i # LogFormat "%v:%p %h %l %u %t \"%r\" %>s %O \"%{Referer}i\" \"%{User-Agent}i\"" vhost_combined LogFormat "%h %l %u %t \"%r\" %>s %O \"%{Referer}i\" \"%{User-Agent}i\"" combined LogFormat "%h %l %u %t \"%r\" %>s %O" common LogFormat "%{Referer}i -> %U" referer LogFormat "%{User-agent}i" agent I have no idea where to look to try and debug this problem or investigate further. Any suggestions?

  Read the article

• Kerberos service on win2k dc will not start following disk failure

  - by iwilson68

  Hi, I have a win2k (mixed mode domain) with 4 DCS. One of these also acts an exchange 2000 server which uses 2 logical volumes from an MSA 2000 array. AD etc is stored on local drives. We experienced a problem last week when the raid array fell back to a redundant controller and this temporarily meant that the two logical drives were not visible to the server for around 5 minutes and a couple of reboots. The log records these Events as Type: Warning Event Source: Disk Event Category: None Event ID: 51 Date: 06/11/2009 Time: 11:46:23 User: N/A Computer: server1 Description: An error was detected on device \Device\Harddisk1\DR1 during a paging operation. Following these problems, the server “kerberos Key Distribution” service refuses to start with an “error.31 a device attached to the system is not functioning”. All other automatic start services (including net logon) are running and there are no DNS issues etc. All devices are also functioning but the two logical MSA disks are now numbered in the Windows Disk Management MMC as 2 and 4 and I suspect that they may have previously been identified as disks 1 & 2 and perhaps windows still sees this as an ongoing failure?? Replication has not been affected but obviously there are many audit failures in the security log relating to users and workstations presumably linked to the Kerberos issue. Attempting to manually start the kerberos service generates the following in the System Log. Event Type: Error Event Source: Service Control Manager Event Category: None Event ID: 7023 Date: 09/11/2009 Time: 09:46:55 User: N/A Computer: Server1 Description: The Kerberos Key Distribution Center service terminated with the following error: A device attached to the system is not functioning. DCDIAG passes all tests except “Advertising” and “Services” which I believe relate directly to the failure of Kerberos only. Any advice would be appreciated.

  Read the article

• Windows Task Scheduler fails on EventData instruction

  - by Pete

  The Scheduled Task fails on the Event Data instruction in this XML: <ValueQueries> <Value name="eventChannel">Event/System/Channel</Value> <Value name="eventRecordID">Event/System/EventRecordID</Value> <Value name="eventData">Event/EventData/Data</Value> </ValueQueries> The other 2 fields can be passed as arguments and the EventData syntax matches other websites, so I don't know why it's failing. This is the Event Viewer XML: <Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event"> <System> <Provider Name="Aptify.ExceptionManagerPublishedException" /> <EventID Qualifiers="0">0</EventID> <Level>2</Level> <Task>0</Task> <Keywords>0x80000000000000</Keywords> <TimeCreated SystemTime="2013-11-07T19:39:14.000000000Z" /> <EventRecordID>97555</EventRecordID> <Channel>Application</Channel> <Computer>[Computer Name]</Computer> <Security /> </System> <EventData> <Data>General Information ********************************************* Additional Info: ExceptionManager.MachineName: [Computer Name] ExceptionManager.TimeStamp: 11/7/2013 12:39:14 PM ExceptionManager.FullName: AptifyExceptionManagement, Version=4.0.0.0, Culture=neutral, PublicKeyToken=[key] ExceptionManager.AppDomainName: Aptify Shell.exe ExceptionManager.ThreadIdentity: ExceptionManager.WindowsIdentity: ACA_DOMAIN\pbassett 1) Exception Information ********************************************* Exception Type: Aptify.Framework.BusinessLogic.GenericEntity.AptifyGenericEntityValidationException Entity: Tasks ErrorString: Task Type "Make Contact" is not active. MachineName: [machine] CreatedDateTime: 11/7/2013 12:39:14 PM AppDomainName: Aptify Shell.exe ThreadIdentityName: WindowsIdentityName: [identity] Severity: 0 ErrorNumber: 0 Message: Task Type "Make Contact" is not active. Data: System.Collections.ListDictionaryInternal TargetSite: Boolean Save(Boolean, System.String ByRef, Sys tem.String) HelpLink: NULL Source: AptifyGenericEntity StackTrace Information ********************************************* at Aptify.Framework.BusinessLogic.GenericEntity.AptifyGenericEntity.Save(Boolean AllowGUI, String& ErrorString, String TransactionID)</Data> </EventData> </Event>

  Read the article

• "Windows cannot find" file when opening Excel spreadsheet

  - by DanH

  For all of my Excel spreadsheets when I attempt to open them (by double-clicking in explorer) I get the message "Windows cannot find C:...". The files are there, and are valid zip files as seen by 7-Zip. There are no apparent lock files in the directories. I did just install Norton-360 over the weekend (replacing Kasperski), but the Norton log shows no events related to Excel. However, while installing Norton I did reboot with some Excel files open. Presumably something is hosed in my Excel configuration but I don't know what. Update (Before actually posting) -- I found an article that suggested turning off Advanced Option "Ignore other applications that use DDE", then doing excel.exe /unregister followed by excel.exe /register. I tried this but I suspect that the two Excel calls were ignored (Excel opened, but no obvious change). With that option off the spreadsheets load OK, but not with it on. And, curiously, spreadsheets load OK with the option on or off if I open Excel first and then open the spreadsheet in it. Does anyone have any idea what effect leaving that option off will have? Update 2 -- I tried running the "repair" option. It said it corrected a couple of config things (without saying what they were), but I still get a failure if I double-click an Excel file with the "Ignore other applications..." option checked. Update 3 -- I managed to fix this problem, but failed at the time to come back and say what I did, and now I can't remember for sure. But I think it had something to do with "Options"/"Save" and some of the values there. Something to do with AutoRecover, perhaps. (Possibly there was a file in recovery and I had to specify "Disable AutoRecover for this workbook" to let bring-up get past it. Or perhaps the AutoRecover file location was hosed.) Anyway, if it happens to someone else, and you find the fix, post it below and I'll mark it answered.

  Read the article

• Nginx + uWSGI + Django performance stuck on 100rq/s

  - by dancio

  I have configured Nginx with uWSGI and Django on CentOS 6 x64 (3.06GHz i3 540, 4GB), which should easily handle 2500 rq/s but when I run ab test ( ab -n 1000 -c 100 ) performance stops at 92 - 100 rq/s. Nginx: user nginx; worker_processes 2; events { worker_connections 2048; use epoll; } uWSGI: Emperor /usr/sbin/uwsgi --master --no-orphans --pythonpath /var/python --emperor /var/python/*/uwsgi.ini [uwsgi] socket = 127.0.0.2:3031 master = true processes = 5 env = DJANGO_SETTINGS_MODULE=x.settings env = HTTPS=on module = django.core.handlers.wsgi:WSGIHandler() disable-logging = true catch-exceptions = false post-buffering = 8192 harakiri = 30 harakiri-verbose = true vacuum = true listen = 500 optimize = 2 sysclt changes: # Increase TCP max buffer size setable using setsockopt() net.ipv4.tcp_rmem = 4096 87380 8388608 net.ipv4.tcp_wmem = 4096 87380 8388608 net.core.rmem_max = 8388608 net.core.wmem_max = 8388608 net.core.netdev_max_backlog = 5000 net.ipv4.tcp_max_syn_backlog = 5000 net.ipv4.tcp_window_scaling = 1 net.core.somaxconn = 2048 # Avoid a smurf attack net.ipv4.icmp_echo_ignore_broadcasts = 1 # Optimization for port usefor LBs # Increase system file descriptor limit fs.file-max = 65535 I did sysctl -p to enable changes. Idle server info: top - 13:34:58 up 102 days, 18:35, 1 user, load average: 0.00, 0.00, 0.00 Tasks: 118 total, 1 running, 117 sleeping, 0 stopped, 0 zombie Cpu(s): 0.0%us, 0.0%sy, 0.0%ni,100.0%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 3983068k total, 2125088k used, 1857980k free, 262528k buffers Swap: 2104504k total, 0k used, 2104504k free, 606996k cached free -m total used free shared buffers cached Mem: 3889 2075 1814 0 256 592 -/+ buffers/cache: 1226 2663 Swap: 2055 0 2055 **During the test:** top - 13:45:21 up 102 days, 18:46, 1 user, load average: 3.73, 1.51, 0.58 Tasks: 122 total, 8 running, 114 sleeping, 0 stopped, 0 zombie Cpu(s): 93.5%us, 5.2%sy, 0.0%ni, 0.2%id, 0.0%wa, 0.1%hi, 1.1%si, 0.0%st Mem: 3983068k total, 2127564k used, 1855504k free, 262580k buffers Swap: 2104504k total, 0k used, 2104504k free, 608760k cached free -m total used free shared buffers cached Mem: 3889 2125 1763 0 256 595 -/+ buffers/cache: 1274 2615 Swap: 2055 0 2055 iotop 30141 be/4 nginx 0.00 B/s 7.78 K/s 0.00 % 0.00 % nginx: wo~er process Where is the bottleneck ? Or what am I doing wrong ?

  Read the article

• Reducing IO caused by nginx

  - by glumbo

  I have a lot of free RAM but my IO is always 100 %util or very close. What ways can I reduce IO by using more RAM? My iotop shows nginx worker processes with the highest io rate. This is a file server serving files ranging from 1mb to 2gb. Here is my nginx.conf #user nobody; worker_processes 32; worker_rlimit_nofile 10240; worker_rlimit_sigpending 32768; error_log logs/error.log crit; #pid logs/nginx.pid; events { worker_connections 51200; } http { include mime.types; default_type application/octet-stream; access_log off; limit_conn_log_level info; log_format xfs '$arg_id|$arg_usr|$remote_addr|$body_bytes_sent|$status'; sendfile off; tcp_nopush off; tcp_nodelay on; directio 4m; output_buffers 3 512k; reset_timedout_connection on; open_file_cache max=5000 inactive=20s; open_file_cache_valid 30s; open_file_cache_min_uses 2; open_file_cache_errors on; client_body_buffer_size 32k; server_tokens off; autoindex off; keepalive_timeout 0; #keepalive_timeout 65;

  Read the article

• Only one domains not resolving via Windows DNS server at multiple locations, but is at others

  - by Brett G

  I'm having quite a weird issue. Had mail delivery issues to a specific domain. After looking closer, I realized that the DNS for that domain isn't resolving via the in-house Windows 2003 SP2 DNS server. C:\>nslookup foodmix.net Server: DC.DOMAIN.com Address: 10.1.1.1 DNS request timed out. timeout was 2 seconds. DNS request timed out. timeout was 2 seconds. *** Request to DC.DOMAIN.com timed-out (DC.DOMAIN.com and 10.1.1.1 are generic values to replace the actual ones) Even if I run this nslookup from the DC.DOMAIN.com server, I get the same result. However, all other requests are working as they should. I tried it on severs at completely separate organizations on different networks(Windows 2003 AD servers). The weird thing is some of these were having the same exact issue. However using public DNS servers work. I have tried clearing the DNS cache, restarting the server, restarting the services, etc. Nothing has worked. One weird event I noticed in the DNS Server Event Logs that might be related is an event ID of 5504 with the following description: The DNS server encountered an invalid domain name in a packet from 192.33.4.12. The packet will be rejected. The event data contains the DNS packet. For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. In the data section below, I can see the following mentioned: ns2.webhostingstar.com Which happens to be the nameserver for the domain in question. Several discussion threads and a MS KB have pointed to disabling EDNS. I have done this via "dnscmd /config /enableednsprobes 0" and it has not fixed the issue.

  Read the article

• CentOS Client - Unable to Establish iSCSI connection with multiple interfaces on the initiator

  - by slashdot

  So after upgrading to CentOS 6.2, I am seemingly no longer able to login into my iSCSI targets. I have multiple interfaces on different subnets on the system, and I first thought that it had to do with the fact that I may not be binding correct interfaces, which seems to be the case when looking at netstat, as this is clearly wrong: [root]? netstat -na|grep .90 tcp 0 1 10.10.100.60:42354 10.10.8.90:3260 SYN_SENT tcp 0 1 10.10.100.60:40777 10.10.9.90:3260 SYN_SENT I then went ahead and disabled all but one interface, and so as a result netstat appears to be correct, but the issue with login remains. I am positive that the target never sees a packet, because I see nothing by SYN_SENT. I know the problem is on my client, because the target is servicing multiple systems, none of which are CentOS 6.2. At this point I am pretty confident that some things changed between CentOS 6.0/6.1 and 6.2. So, if anyone have any thoughts, or ran into this, I would very much like to hear your thoughts. [root]? iscsiadm --mode node --targetname iqn.2011-12.dom.homer:01:lab-centos-servers-00001 --portal 10.10.8.90:3260,2 --interface=sw-iscsi-0 --login Logging in to [iface: sw-iscsi-0, target: iqn.2011-12.dom.homer:01:lab-centos-servers-00001, portal: 10.10.8.90,3260] (multiple) iscsiadm: Could not login to [iface: sw-iscsi-0, target: iqn.2011-12.dom.homer:01:lab-centos-servers-00001, portal: 10.10.8.90,3260]. iscsiadm: initiator reported error (8 - connection timed out) iscsiadm: Could not log into all portals [root]? netstat -rn Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 10.10.8.0 0.0.0.0 255.255.255.0 U 0 0 0 eth2.7 10.10.9.0 0.0.0.0 255.255.255.0 U 0 0 0 eth3.7 10.10.100.0 0.0.0.0 255.255.252.0 U 0 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth1 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth2 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth3 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth2.7 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth3.7 0.0.0.0 10.10.100.1 0.0.0.0 UG 0 0 0 eth0 Output of ip addr show for the two interfaces involved: [root]? for i in 2.7 3.7; do ip addr show eth$i; done 6: eth2.7@eth2: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP link/ether 00:0c:29:94:5b:8d brd ff:ff:ff:ff:ff:ff inet 10.10.8.60/24 brd 10.10.8.255 scope global eth2.7 inet6 fe80::20c:29ff:fe94:5b8d/64 scope link valid_lft forever preferred_lft forever 7: eth3.7@eth3: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP link/ether 00:0c:29:94:5b:97 brd ff:ff:ff:ff:ff:ff inet 10.10.9.60/24 brd 10.10.9.255 scope global eth3.7 inet6 fe80::20c:29ff:fe94:5b97/64 scope link valid_lft forever preferred_lft forever Update 01/06/2012: This issue is getting even more interesting by the day it seems. I went a few weeks back and grabbed a snapshot of this system from before upgrading to 6.2. I spun up a new system from the snapshot, and reconfigured interface info and host keys, as well as iSCSI initiator and iscsi interface info to match new MACs. Changed nothing else. Then, I attempted to connect to my targets, and no issues at all. I cannot say that this was unexpected. I then went ahead and compared sysctl settings from both systems and there were differences after the upgrade, but nothing seemingly relevant to iSCSI or IP that could contribute to this. I also noticed that by default now two sessions per connection were enabled after the upgrade, but I changed it back to 1 session in /etc/iscsi/iscsid.conf. On the problematic system we can see that source interface is seemingly wrong, but even when I disable the 10.10.100 interface, problems persist. So, while this may be relevant, I could not validate it for certain. Needless to say, further research is necessary. Something is clearly different between releases. Working system is on 6.1, and non-working is 6.2. ::Working System:: tcp 0 0 10.10.8.210:39566 10.10.8.90:3260 ESTABLISHED tcp 0 0 10.10.9.210:46518 10.10.9.90:3260 ESTABLISHED [root]? ip route show 10.10.8.0/24 dev eth2.6 proto kernel scope link src 10.10.8.210 10.10.9.0/24 dev eth3.7 proto kernel scope link src 10.10.9.210 10.10.100.0/22 dev eth0 proto kernel scope link src 10.10.100.210 169.254.0.0/16 dev eth0 scope link metric 1002 169.254.0.0/16 dev eth2.6 scope link metric 1006 169.254.0.0/16 dev eth3.7 scope link metric 1007 default via 10.10.100.1 dev eth0 ::Non-working System:: tcp 0 1 10.10.100.60:44737 10.10.9.90:3260 SYN_SENT tcp 0 1 10.10.100.60:55479 10.10.8.90:3260 SYN_SENT [root]? ip route show 10.10.8.0/24 dev eth2.6 proto kernel scope link src 10.10.8.60 10.10.9.0/24 dev eth3.7 proto kernel scope link src 10.10.9.60 10.10.100.0/22 dev eth0 proto kernel scope link src 10.10.100.60 169.254.0.0/16 dev eth0 scope link metric 1002 169.254.0.0/16 dev eth2.6 scope link metric 1006 169.254.0.0/16 dev eth3.7 scope link metric 1007 default via 10.10.100.1 dev eth0 And the result is still same: [root]? iscsiadm: Could not login to [iface: sw-iscsi-0, target: iqn.2011-12.dom.homer:01:lab-centos-servers-00001, portal: 10.10.8.90,3260]. iscsiadm: initiator reported error (8 - connection timed out) iscsiadm: Could not login to [iface: sw-iscsi-1, target: iqn.2011-12.dom.homer:02:lab-centos-servers-00001, portal: 10.10.9.90,3260]. iscsiadm: initiator reported error (8 - connection timed out) iscsiadm: Could not log into all portals Update 01/08/2012: I believe I have been able to figure out the answer to my issue. It is quite obscure and I doubt this will happen to anyone else any time soon. It turns out that setting iface.iscsi_ifacename and iface.hwaddress in the interfaces configuration file is not legal. When one manually adds an iscsi target, such as below, all settings from the interface config file are copied into the node config file, that gets created by the below command. Result is parameters iface.iscsi_ifacename and iface.hwaddress together in the same config file. These parameters are seemingly mutually exclusive, which does not exactly make sense, or there is perhaps an oversight in the codepath. Perhaps I will investigate further. # iscsiadm -m node --op new -T iqn.2011-12.dom.homer:01:lab-centos-servers-00001 -p 10.10.8.90,3260,2 -I sw-iscsi-0 # iscsiadm -m node --op new -T iqn.2011-12.dom.homer:02:lab-centos-servers-00001 -p 10.10.9.90,3260,2 -I sw-iscsi-1 Notice, below I commented out iface.hwaddress and iface.ipaddress, after which I re-added targets, with same command as above. All works just fine. [root]? cat * # BEGIN RECORD 2.0-872.33.el6 iface.iscsi_ifacename = sw-iscsi-0 iface.net_ifacename = eth2.6 #iface.hwaddress = XX:XX:XX:XX:XX:XX #iface.ipaddress = 10.10.8.60 iface.transport_name = tcp iface.vlan_id = 6 iface.vlan_priority = 0 iface.iface_num = 0 iface.mtu = 0 iface.port = 0 # END RECORD # BEGIN RECORD 2.0-872.33.el6 iface.iscsi_ifacename = sw-iscsi-1 iface.net_ifacename = eth3.7 #iface.hwaddress = XX:XX:XX:XX:XX:XX #iface.ipaddress = 10.10.9.60 iface.transport_name = tcp iface.vlan_id = 7 iface.vlan_priority = 0 iface.iface_num = 0 iface.mtu = 0 iface.port = 0 # END RECORD Again, chances of this happening to someone else are slim to none, so likely waste of time typing this up. But, if someone does encounter this issue, I hope this post will help.

  Read the article

• [Ubuntu 10.04] mdadm - Can't get RAID5 Array To Start

  - by Matthew Hodgkins

  Hello, after a power failure my RAID array refuses to start. When I boot I have to sudo mdadm --assemble --force /dev/md0 /dev/sdb1 /dev/sdc1 /dev/sdd1 /dev/sde1 /dev/sdf1 /dev/sdg1 to get mdadm to notice the array. Here are the details (after I force assemble). sudo mdadm --misc --detail /dev/md0: /dev/md0: Version : 00.90 Creation Time : Sun Apr 25 01:39:25 2010 Raid Level : raid5 Used Dev Size : 1465135872 (1397.26 GiB 1500.30 GB) Raid Devices : 6 Total Devices : 6 Preferred Minor : 0 Persistence : Superblock is persistent Update Time : Thu Jun 17 23:02:38 2010 State : active, Not Started Active Devices : 6 Working Devices : 6 Failed Devices : 0 Spare Devices : 0 Layout : left-symmetric Chunk Size : 128K UUID : 44a8f730:b9bea6ea:3a28392c:12b22235 (local to host hodge-fs) Events : 0.1249691 Number Major Minor RaidDevice State 0 8 65 0 active sync /dev/sde1 1 8 81 1 active sync /dev/sdf1 2 8 97 2 active sync /dev/sdg1 3 8 49 3 active sync /dev/sdd1 4 8 33 4 active sync /dev/sdc1 5 8 17 5 active sync /dev/sdb1 mdadm.conf: # by default, scan all partitions (/proc/partitions) for MD superblocks. # alternatively, specify devices to scan, using wildcards if desired. DEVICE partitions /dev/sdb1 /dev/sdb1 # auto-create devices with Debian standard permissions CREATE owner=root group=disk mode=0660 auto=yes # automatically tag new arrays as belonging to the local system HOMEHOST <system> # definitions of existing MD arrays ARRAY /dev/md0 level=raid5 num-devices=6 UUID=44a8f730:b9bea6ea:3a28392c:12b22235 Any help would be appreciated.

  Read the article

• Folder Redirection/Offline Files on Win 7 | Folders are empty when not connected to the domain

  - by Matt

  I've been struggling with this issue for days and cannot seem to find anyone else with a similar issue. I will note first that I have tried using both roaming profiles and the group policy setting for force local profiles.... now onto the problem. What I am trying to do is have my teachers accounts log onto their laptops using their domain credentials. Once logged in their desktop and documents are redirected to a network share //server/redirects/documents/. This works fine when the computer is connected to the domain network. Offline File Sync works great and caches the files locally. However this all breaks down when the user logs in when the computer is no longer connected to the domain network. When the user logs in the desktop and documents are empty. What I find very odd is if I manually go to the offline file folder all of the files are there, The group policy folder redirection does not execute to the offline folder. Is this by Design? (It does not work like this on Vista, I have the exact same group policy settings set on vista machines and it works flawlessly). Additional Info When I look at the event log there is no folder redirection events at all when user logs in and is not connected to the network. In addition a new profile is create in c:/users/username.domain.00x. Every log in creates an additional profile. There is a event that states that a registry files were still in use. Any help would be appreciated.

  Read the article

• How can I parse/ transform text log data before it gets captured in SCOM 2007 R2?

  - by Abs

  I'm pretty much a noob with System Center Operations Manager 2007, and I'm probably missing something pretty basic, but I'm stumped anyway. We're setting up monitoring on some of our servers, and we'd like to capture data from some plain text log files (e.g. DNS debug logs, DHCP logs). It looks to me like I can set up a generic text file monitoring rule and get events captured into the main Ops Manager database, but my understanding is that the whole line of text from the plain text log gets captured as one field. In an ideal world, we'd be able to parse or transform that log file data to make it easier to query later. Is this possible? Is it easy? Do I have to buy expensive 3rd-party software to do it? One more thing: it would be even better if there was a way to stuff this data into the Audit Collection Services (ACS) database instead of the main one, but I'll take what I can get. Any help would be greatly appreciated.

  Read the article

• VMware Data Recovery error -3960 and Event ID 8193 on Windows Server 2003

  - by flooooo

  I've been trying to solve this problem since a few days now without any success. What I'm trying is to make a backup of a virtual machine running Windows Server 2003 SP 2 using VMware Data Recovery 2.0.0.1861. When starting the backup task it tries to make a snapshot of the virtual machine using VSS which fails with error: Event Type: Error Event Source: VSS Event Category: None Event ID: 8193 Date: 05.06.2012 Time: 12:12:01 User: N/A Computer: LEGOLAS Description: Volume Shadow Copy Service error: Unexpected error calling routine RegSaveKeyExW. hr = 0x800703f8. For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. Data: 0000: 2d 20 43 6f 64 65 3a 20 - Code: 0008: 57 52 54 52 45 47 52 43 WRTREGRC 0010: 30 30 30 30 30 33 39 36 00000396 0018: 2d 20 43 61 6c 6c 3a 20 - Call: 0020: 57 52 54 52 45 47 52 43 WRTREGRC 0028: 30 30 30 30 30 33 31 38 00000318 0030: 2d 20 50 49 44 3a 20 20 - PID: 0038: 30 30 30 30 36 34 38 38 00006488 0040: 2d 20 54 49 44 3a 20 20 - TID: 0048: 30 30 30 30 34 33 38 34 00004384 0050: 2d 20 43 4d 44 3a 20 20 - CMD: 0058: 43 3a 5c 57 49 4e 44 4f C:\WINDO 0060: 57 53 5c 53 79 73 74 65 WS\Syste 0068: 6d 33 32 5c 76 73 73 76 m32\vssv 0070: 63 2e 65 78 65 20 20 20 c.exe 0078: 2d 20 55 73 65 72 3a 20 - User: 0080: 4e 54 20 41 55 54 48 4f NT AUTHO 0088: 52 49 54 59 5c 53 59 53 RITY\SYS 0090: 54 45 4d 20 20 20 20 20 TEM 0098: 2d 20 53 69 64 3a 20 20 - Sid: 00a0: 53 2d 31 2d 35 2d 31 38 S-1-5-18 This machine was converted p2v. I have no idea where to search for the problem and what to do. Google showed a few result but none of them were useful for me. Please help me. If you need further information I'll tell you - just ask!

  Read the article

• Windows errors, how do I find root cause and fix it? Getting several errors

  - by Eric Martin

  My server is having issues and not responding to customer's https requests. I checked the event viewer and found several errors. These two are listed a couple of times: WINS encountered a database error. This may or may not be a serious error. WINS will try to recover from it. You can check the database error events under 'Application Log' category of the Event Viewer for the Exchange Component, ESENT, source to find out more details about database errors. If you continue to see a large number of these errors consistently over time (a span of few hours), you may want to restore the WINS database from a backup. The error number is in the second DWORD of the data section. And this one: An error occured while using SSL configuration for socket address 0.0.0.0:444. The error status code is contained within the returned data. SQL Server is not ready to accept new client connections. Wait a few minutes before trying again. If you have access to the error log, look for the informational message that indicates that SQL Server is ready before trying to connect again. [CLIENT: xxx.xxx.xxxx.xxx] I also found this in the event viewer but the computer has been restarted since this message and I have not seen it again. Configuring the Page file for crash dump failed. Make sure there is a page file on the boot partition and that is large enough to contain all physical memory. This is my virtual memory settings: I'm not familiar with WINS so I wasn't sure if that is where I start or how to resolve it. Is the WINS error causing the other problems or should I be looking somewhere else?

  Read the article

• Where to place Nginx IP blacklist config file?

  - by ProfessionalAmateur

  I have an Nginx web server hosting two sites. I created a blockips.conf file to blacklist IP addresses that are constantly probing the server and included this file in the nginx.conf file. However in my access logs for the sites I still see these IP addresses showing up. Do I need to include the black list in each site's conf instead of the global conf for Nginx? Here is my nginx.conf user nginx; worker_processes 1; error_log /var/log/nginx/error.log warn; pid /var/run/nginx.pid; events { worker_connections 1024; } http { include /etc/nginx/mime.types; default_type application/octet-stream; log_format main '$remote_addr - $remote_user [$time_local] "$request" ' '$status $body_bytes_sent "$http_referer" ' '"$http_user_agent" "$http_x_forwarded_for"'; access_log /var/log/nginx/access.log main; sendfile on; keepalive_timeout 65; include /etc/nginx/conf.d/*.conf; # Load virtual host configuration files. include /etc/nginx/sites-enabled/*; # BLOCK SPAMMERS IP ADDRESSES include /etc/nginx/conf.d/blockips.conf; } blockips.conf deny 58.218.199.250; access.log still shows this IP address. 58.218.199.250 - - [27/Sep/2012:06:41:03 -0600] "GET http://59.53.91.9/proxy/judge.php HTTP/1.1" 403 570 "-" "Mozilla/4.0 (compatible; MSIE 6.0; Windows NT 5.1)" "-" What am I doing incorrectly?

  Read the article

• CryptSvc not matched by Windows 7 Firewall rule

  - by theultramage

  I am using Windows Firewall in conjunction with a third-party tool to get notified about new outbound connection attempts (Windows Firewall Notifier or Windows Firewall Control). The way these tools do it is by setting the firewall to deny by default, and to add an auditing policy to log blocked connections into the Security event log. Then they watch the log, and display notification about newly added entries. netsh advfirewall set allprofiles firewallpolicy blockinbound,blockoutbound auditpol /set /subcategory:{0CCE9226-69AE-11D9-BED3-505054503030} /failure:enable With this configuration in place, I now need to craft outbound allow rules for applications and system services. Here is the rule for CryptSvc, the service frequently used for certificate validation and revocation checking: netsh advfirewall firewall add rule name="Windows Cryptographic Services" action=allow enable=yes profile=any program="%SystemRoot%\system32\svchost.exe" service="CryptSvc" dir=out protocol=tcp remoteport=80,443 The problem is, this rule does not work. Unless I change the scope to "all programs and services" (which is really unhealthy), connection denied events like the following will keep appearing in the security log: Event 5157, Microsoft Windows security auditing. The Windows Filtering Platform has blocked a connection. Application Information: Process ID: 1476 (<- svchost.exe with CryptSvc and nothing else) Application Name: \device\harddiskvolume1\windows\system32\svchost.exe Network Information: Direction: Outbound Source Address: 192.168.0.1 Source Port: 49616 Destination Address: 2.16.52.16 Destination Port: 80 Protocol: 6 (<- TCP) To make sure it's CryptSvc, I have let the connection through and reviewed its traffic; I also configured CryptSvc to run in its own svchost instance to make it more obvious: ;sc config CryptSvc type= share sc config CryptSvc type= own So... why is it not matching the firewall rule, and how to fix that?

  Read the article

• Webservice randomly dropping connections - possibly due to firewall nonevent data?

  - by adam

  I have a hosted webapp which requests data from a REST webservice in our office. Each page calls one (or several) webservices, which go from our host, via our firewall (a Watchguard Firebox) to a server in our office. All of a sudden, the app has dramatically slowed. We have determined that the webservice is timing out at random when called externally (it's fine when called within the office network). I'm pretty certain it's our connection which is dropping the webservice call, so I've written a quick php/curl script which calls the webservice over many iterations and shows the various timings. Below is an example output, showing both a failed and a successful call (with a 5 second timeout): http_code namelookup_time connect_time pretransfer_time starttransfer_time total_time 1 0 0.000096 0.0342 0.0000 0.0000 0.0342 2 200 0.000052 0.0332 0.1327 0.1751 0.1752 As per iteration #1 above, failed requests seem to be failing between connect and pretransfer. I'm not sure if this shows that the connection is successfully past the firewall, or could the firewall still cause an issue? Our firewall is showing a series of nondata event log messages for the relevant access rule. Our IT team tells me these are routine, although I can find no mention of these in Google. I'm not sure if this fits in between connect and pretransfer. Having elinated the webservice server (by testing internally) and the live webapp (by testing different code on different external servers, I am left suspecting the connection to the office. Could the firebox nondata events be causing a problem between connect and pretransfer?

  Read the article

• SharePoint Records Center Submitted E-mail Records not picked up

  - by Kenneth Verburg

  We have set up a new SharePoint 2007 site with a Records Repository. We're using Exchange 2007 Managed Folders to route e-mails to this repository based on the 'label' attached to the e-mail as set in the Exchange 2007 journaling options. E-mails added to a Managed Folder get sent to SharePoint, they end up in the "Submitted E-mail Records" list of the Records Repository. That's according to plan, but the e-mails are not routed to the respective document library as defined by the label. Instead an error appears in the event viewer for every e-mail listed in the Submitted E-mail Records list, on every interval of the records repository schedule (set to every two minutes for testing purposes): Value cannot be null, parameter name: g. Sending a document from the SharePoint site iself to the Records Repository via the Send To... link works fine, but e-mails get stuck in the list... We have set Document Libraries in the Respository with and without content types (with matching names with the Label and the Record Routing rule set). Any ideas what could be wrong? This is in the event log: Every two minutes the following error appears in the Application Log: Source: Office SharePoint Server Category: Records Center Type: Error Event ID: 4975 User: N/A Computer: SPS2007 Description: Value cannot be null. Parameter name: g For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp.

  Read the article

• How seriously should I take ECC correctable error warnings?

  - by David Mackintosh

  I have a pile of Sun X2200-M2 servers. These servers have ECC memory. In some of these servers, I am getting warnings in the eLOM about "correctable ECC errors detected", eg: # ssh regress11 ipmitool sel elist 1 | 05/20/2010 | 14:20:27 | Memory CPU0 DIMM2 | Correctable ECC | Asserted 2 | 05/20/2010 | 14:33:47 | Memory CPU0 DIMM2 | Correctable ECC | Asserted ...some more frequently than others. The kernel on this particular system is throwing EDAC errors as well, although with far more frequency than the eLOM is recording ECC events: EDAC k8 MC0: general bus error: participating processor(local node response), time-out(no timeout) memory transaction type(generic read), mem or i/o(mem access), cache level(generic) MC0: CE page 0x42a194, offset 0x60, grain 8, syndrome 0xf654, row 4, channel 1, label "": k8_edac MC0: CE - no information available: k8_edac Error Overflow set EDAC k8 MC0: extended error code: ECC chipkill x4 error EDAC k8 MC0: general bus error: participating processor(local node response), time-out(no timeout) memory transaction type(generic read), mem or i/o(mem access), cache level(generic) MC0: CE page 0x48cb94, offset 0x10, grain 8, syndrome 0xf654, row 5, channel 1, label "": k8_edac MC0: CE - no information available: k8_edac Error Overflow set EDAC k8 MC0: extended error code: ECC chipkill x4 error Now if the server is detecting Uncorrectable ECC, the system resets, so clearly that's bad and removing/replacing the identified stick or pair corrects the issue. But I am thinking that if the error is Correctable, then there's no immediate issue -- I can treat this as a warning and be prepared to pull the stick/pair if an uncorrectable error starts occurring?

  Read the article

• 2008 Sever Randomly reboots.

  - by Jeff

  I'm out of ideas here. We have a 2008 Server that keeps rebooting 2-3 times a day at completely random times with an "Unexpected Shutdown" event. There are no Dumps, no events leading to it just like it loses power then comes back online. I ran a Diagnostic of the power supply and it has had continuous power for months. In addition, the temperature of the processors are maxing out at 40 degrees Celsius. Anyone have any ideas how to figure out why this is restarting all the time? This is a DMZed Web server so it doesn't do too much process wise. Here are the specs: Host Name: ~~~ OS Name: Microsoft Windows Server 2008 R2 Standard OS Version: 6.1.7600 N/A Build 7600 OS Manufacturer: Microsoft Corporation OS Configuration: Standalone Server OS Build Type: Multiprocessor Free Registered Owner: Windows User Registered Organization: Product ID: ~~~ Original Install Date: 5/27/2010, 4:25:47 PM System Boot Time: 2/14/2011, 5:35:01 PM System Manufacturer: HP System Model: ProLiant DL380 G6 System Type: x64-based PC Processor(s): 1 Processor(s) Installed. [01]: Intel64 Family 6 Model 26 Stepping 5 GenuineIntel ~1586 Mhz BIOS Version: HP P62, 8/16/2010 Windows Directory: C:\Windows System Directory: C:\Windows\system32 Boot Device: \Device\HarddiskVolume1 System Locale: en-us;English (United States) Input Locale: en-us;English (United States) Time Zone: (UTC-05:00) Eastern Time (US & Canada) Total Physical Memory: 4,086 MB Available Physical Memory: 2,775 MB Virtual Memory: Max Size: 8,170 MB Virtual Memory: Available: 6,691 MB Virtual Memory: In Use: 1,479 MB Page File Location(s): C:\pagefile.sys

  Read the article

• Application for time and projet management

  - by user10826

  I want to improve the way I organize my projects/tasks/schedule What I do now is: keep an excel sheet with the name of the most important tasks/projects, I look at it at the beginning of each day and decide the ones I will focus on on iCal I write down events for each day, or for a concrete time (13 to 14 hours). I set up each day the tasks I want to accomlish, and allocate them hours I use Things (culture code) to keep info about tasks and projects not very important and which are not time allocated yet (GTD name = someday) I use Mail on Mac and create folders for the mails I want to process with the name of the different projects I save the main info for each project on freemind maps My system works well at the moment but it is pretty complicated to use. I want to make it better and I am looking for something with these requirements: must be 100% offline accessable it should use as less programs/resources as possible, ideally just one program should be able to manage all my info I can use the GTD methodology mixed with priorities and I can allocate each task converted to event on my calendar I can have different daily/weekly, etc views on a calendar to see the "big picture" must run on mac os x leopard price does not matter, I will pay for this So, according to your experience, can you recommend me something like this? Thanks

  Read the article

• Immediately tell which output was sent to stderr

  - by Clinton Blackmore

  When automating a task, it is sensible to test it first manually. It would be helpful, though, if any data going to stderr was immediately recognizeable as such, and distinguishable from the data going to stdout, and to have all the output together so it is obvious what the sequence of events is. One last touch that would be nice is if, at program exit, it printed its return code. All of these things would aid in automating. Yes, I can echo the return code when a program finishes, and yes, I can redirect stdout and stderr; what I'd really like it some shell, script, or easy-to-use redirector that shows stdout in black, shows stderr interleaved with it in red, and prints the exit code at the end. Is there such a beast? [If it matters, I'm using Bash 3.2 on Mac OS X]. Update: Sorry it has been months since I've looked at this. I've come up with a simple test script: #!/usr/bin/env python import sys print "this is stdout" print >> sys.stderr, "this is stderr" print "this is stdout again" In my testing (and probably due to the way things are buffered), rse and hilite display everything from stdout and then everything from stderr. The fifo method gets the order right but appears to colourize everything following the stderr line. ind complained about my stdin and stderr lines, and then put the output from stderr last. Most of these solutions are workable, as it is not atypical for only the last output to go to stderr, but still, it'd be nice to have something that worked slightly better.

  Read the article

• Access denied error 3221225578 with file sharing to Windows server

  - by Ian Boyd

  i'm trying to access the shares on a server. The credential box appears, and i enter in a correct username and password, and i get access denied. The silly thing is that i can Remote Desktop to the server (using the same credentials), and i can check the Security event log for the access denied errors: Event Type: Failure Audit Event Source: Security Event Category: Account Logon Event ID: 681 Date: 3/19/2011 Time: 11:54:39 PM User: NT AUTHORITY\SYSTEM Computer: STALWART Description: The logon to account: Administrator by: MICROSOFT_AUTHENTICATION_PACKAGE_V1_0 from workstation: HARPAX failed. The error code was: 3221225578 and Event Type: Failure Audit Event Source: Security Event Category: Logon/Logoff Event ID: 529 Date: 3/19/2011 Time: 11:54:39 PM User: NT AUTHORITY\SYSTEM Computer: STALWART Description: Logon Failure: Reason: Unknown user name or bad password User Name: Administrator Domain: stalwart Logon Type: 3 Logon Process: NtLmSsp Authentication Package: NTLM Workstation Name: HARPAX Looking up the error code (3221225578), i get an article on Technet: Audit Account Logon Events By Randy Franklin Smith ... Table 1 - Error Codes for Event ID 681 Error Code Reason for Logon Failure 3221225578 The username is correct, but the password is wrong. Which would seem to indicate that the username is correct, but the password is wrong. i've tried the password many times, uppercase, lowercase, on different user accounts, with and without prefixing the username with servername\username. What gives that i cannot access the server over file sharing, but i can access it over RDP?

  Read the article

< Previous Page | 261 262 263 264 265 266 267 268 269 270 271 272  | Next Page >