Search Results

Search found 31254 results on 1251 pages for 'manual hunk edit mode'.

Page 267/1251 | < Previous Page | 263 264 265 266 267 268 269 270 271 272 273 274  | Next Page >

• Cisco ASA 5505 - L2TP over IPsec

  - by xraminx

  I have followed this document on cisco site to set up the L2TP over IPsec connection. When I try to establish a VPN to ASA 5505 from my Windows XP, after I click on "connect" button, the "Connecting ...." dialog box appears and after a while I get this error message: Error 800: Unable to establish VPN connection. The VPN server may be unreachable, or security parameters may not be configured properly for this connection. ASA version 7.2(4) ASDM version 5.2(4) Windows XP SP3 Windows XP and ASA 5505 are on the same LAN for test purposes. Edit 1: There are two VLANs defined on the cisco device (the standard setup on cisco ASA5505). - port 0 is on VLAN2, outside; - and ports 1 to 7 on VLAN1, inside. I run a cable from my linksys home router (10.50.10.1) to the cisco ASA5505 router on port 0 (outside). Port 0 have IP 192.168.1.1 used internally by cisco and I have also assigned the external IP 10.50.10.206 to port 0 (outside). I run a cable from Windows XP to Cisco router on port 1 (inside). Port 1 is assigned an IP from Cisco router 192.168.1.2. The Windows XP is also connected to my linksys home router via wireless (10.50.10.141). Edit 2: When I try to establish vpn, the Cisco device real time Log viewer shows 7 entries like this: Severity:5 Date:Sep 15 2009 Time: 14:51:29 SyslogID: 713904 Destination IP = 10.50.10.141, Decription: No crypto map bound to interface... dropping pkt Edit 3: This is the setup on the router right now. Result of the command: "show run" : Saved : ASA Version 7.2(4) ! hostname ciscoasa domain-name default.domain.invalid enable password HGFHGFGHFHGHGFHGF encrypted passwd NMMNMNMNMNMNMN encrypted names name 192.168.1.200 WebServer1 name 10.50.10.206 external-ip-address ! interface Vlan1 nameif inside security-level 100 ip address 192.168.1.1 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 ip address external-ip-address 255.0.0.0 ! interface Vlan3 no nameif security-level 50 no ip address ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 ! interface Ethernet0/3 ! interface Ethernet0/4 ! interface Ethernet0/5 ! interface Ethernet0/6 ! interface Ethernet0/7 ! ftp mode passive dns server-group DefaultDNS domain-name default.domain.invalid object-group service l2tp udp port-object eq 1701 access-list outside_access_in remark Allow incoming tcp/http access-list outside_access_in extended permit tcp any host WebServer1 eq www access-list outside_access_in extended permit udp any any eq 1701 access-list inside_nat0_outbound extended permit ip any 192.168.1.208 255.255.255.240 access-list inside_cryptomap_1 extended permit ip interface outside interface inside pager lines 24 logging enable logging asdm informational mtu inside 1500 mtu outside 1500 ip local pool PPTP-VPN 192.168.1.210-192.168.1.220 mask 255.255.255.0 icmp unreachable rate-limit 1 burst-size 1 asdm image disk0:/asdm-524.bin no asdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 0 access-list inside_nat0_outbound nat (inside) 1 0.0.0.0 0.0.0.0 static (inside,outside) tcp interface www WebServer1 www netmask 255.255.255.255 access-group outside_access_in in interface outside timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute http server enable http 192.168.1.0 255.255.255.0 inside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec transform-set TRANS_ESP_3DES_SHA esp-3des esp-sha-hmac crypto ipsec transform-set TRANS_ESP_3DES_SHA mode transport crypto ipsec transform-set TRANS_ESP_3DES_MD5 esp-3des esp-md5-hmac crypto ipsec transform-set TRANS_ESP_3DES_MD5 mode transport crypto map outside_map 1 match address inside_cryptomap_1 crypto map outside_map 1 set transform-set TRANS_ESP_3DES_MD5 crypto map outside_map interface inside crypto isakmp enable outside crypto isakmp policy 10 authentication pre-share encryption 3des hash md5 group 2 lifetime 86400 telnet timeout 5 ssh timeout 5 console timeout 0 dhcpd auto_config outside ! dhcpd address 192.168.1.2-192.168.1.33 inside dhcpd enable inside ! group-policy DefaultRAGroup internal group-policy DefaultRAGroup attributes dns-server value 192.168.1.1 vpn-tunnel-protocol IPSec l2tp-ipsec username myusername password FGHFGHFHGFHGFGFHF nt-encrypted tunnel-group DefaultRAGroup general-attributes address-pool PPTP-VPN default-group-policy DefaultRAGroup tunnel-group DefaultRAGroup ipsec-attributes pre-shared-key * tunnel-group DefaultRAGroup ppp-attributes no authentication chap authentication ms-chap-v2 ! ! prompt hostname context Cryptochecksum:a9331e84064f27e6220a8667bf5076c1 : end

  Read the article

• help setting up an IPSEC vpn from my linux box

  - by robthewolf

  I have an office with a router and a remote server (Linux - Ubuntu 10.10). Both locations need to connect to a data supplier through a VPN. The VPN is an IPSEC gateway. I was able to configure my Linksys rv42 router to create a VPN connection successfully and now I need to do the same for Linux server. I have been messing around with this for too long. First I tried OpenVPN, but that is SSL and not IPSEC. Then I tried Shrew. I think I have the settings correct but I haven't been able to create the connection. It maybe that I have to use something else like a direct IPSEC config or something like that. If someone knows of a way to turn the following settings that I have been given below into a working IPSEC VPN connection I would be very grateful. Here are the settings I was given that must be used to connect to my supplier: Local destination network: 192.168.4.0/24 Local destination hosts: 192.168.4.100 Remote destination network: 192.167.40.0/24 Remote destination hosts: 192.168.40.27 VPN peering point: xxx.xxx.xxx.xxx Then they have given me the following details: IPSEC/ISAKMP Phase 1 Parameters: Authentication method: pre shared secret Diffie Hellman group: group 2 Encryption Algorithm: 3DES Lifetime in seconds:28800 Phase 2 parameters: IPSEC security: ESP Encryption algortims: 3DES Authentication algorithms: MD5 lifetime in seconds: 28800 pfs: disabled Here are the settings from my attempt to use shrew: n:version:2 n:network-ike-port:500 n:network-mtu-size:1380 n:client-addr-auto:0 n:network-frag-size:540 n:network-dpd-enable:1 n:network-notify-enable:1 n:client-banner-enable:1 n:client-dns-used:1 b:auth-mutual-psk:YjJzN2QzdDhyN2EyZDNpNG42ZzQ= n:phase1-dhgroup:2 n:phase1-keylen:0 n:phase1-life-secs:28800 n:phase1-life-kbytes:0 n:vendor-chkpt-enable:0 n:phase2-keylen:0 n:phase2-pfsgroup:-1 n:phase2-life-secs:28800 n:phase2-life-kbytes:0 n:policy-nailed:0 n:policy-list-auto:1 n:client-dns-auto:1 n:network-natt-port:4500 n:network-natt-rate:15 s:client-dns-addr:0.0.0.0 s:client-dns-suffix: s:network-host:xxx.xxx.xxx.xxx s:client-auto-mode:pull s:client-iface:virtual s:client-ip-addr:192.168.4.0 s:client-ip-mask:255.255.255.0 s:network-natt-mode:enable s:network-frag-mode:disable s:auth-method:mutual-psk s:ident-client-type:address s:ident-client-data:192.168.4.0 s:ident-server-type:address s:ident-server-data:192.168.40.0 s:phase1-exchange:aggressive s:phase1-cipher:3des s:phase1-hash:md5 s:phase2-transform:3des s:phase2-hmac:md5 s:ipcomp-transform:disabled Finally here is the debug output from the shrew log: 10/12/22 17:22:18 ii : ipc client process thread begin ... 10/12/22 17:22:18 < A : peer config add message 10/12/22 17:22:18 DB : peer added ( obj count = 1 ) 10/12/22 17:22:18 ii : local address 217.xxx.xxx.xxx selected for peer 10/12/22 17:22:18 DB : tunnel added ( obj count = 1 ) 10/12/22 17:22:18 < A : proposal config message 10/12/22 17:22:18 < A : proposal config message 10/12/22 17:22:18 < A : client config message 10/12/22 17:22:18 < A : local id '192.168.4.0' message 10/12/22 17:22:18 < A : remote id '192.168.40.0' message 10/12/22 17:22:18 < A : preshared key message 10/12/22 17:22:18 < A : peer tunnel enable message 10/12/22 17:22:18 DB : new phase1 ( ISAKMP initiator ) 10/12/22 17:22:18 DB : exchange type is aggressive 10/12/22 17:22:18 DB : 217.xxx.xxx.xxx:500 <- 206.xxx.xxx.xxx:500 10/12/22 17:22:18 DB : c1a8b31ac860995d:0000000000000000 10/12/22 17:22:18 DB : phase1 added ( obj count = 1 ) 10/12/22 17:22:18 : security association payload 10/12/22 17:22:18 : - proposal #1 payload 10/12/22 17:22:18 : -- transform #1 payload 10/12/22 17:22:18 : key exchange payload 10/12/22 17:22:18 : nonce payload 10/12/22 17:22:18 : identification payload 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports nat-t ( draft v00 ) 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports nat-t ( draft v01 ) 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports nat-t ( draft v02 ) 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports nat-t ( draft v03 ) 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports nat-t ( rfc ) 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports DPDv1 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local is SHREW SOFT compatible 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local is NETSCREEN compatible 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local is SIDEWINDER compatible 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local is CISCO UNITY compatible 10/12/22 17:22:18 = : cookies c1a8b31ac860995d:0000000000000000 10/12/22 17:22:18 = : message 00000000 10/12/22 17:22:18 - : send IKE packet 217.xxx.xxx.xxx:500 - 206.xxx.xxx.xxx:500 ( 484 bytes ) 10/12/22 17:22:18 DB : phase1 resend event scheduled ( ref count = 2 ) 10/12/22 17:22:18 ii : opened tap device tap0 10/12/22 17:22:28 - : resend 1 phase1 packet(s) 217.xxx.xxx.xxx:500 - 206.xxx.xxx.xxx:500 10/12/22 17:22:38 - : resend 1 phase1 packet(s) 217.xxx.xxx.xxx:500 - 206.xxx.xxx.xxx:500 10/12/22 17:22:48 - : resend 1 phase1 packet(s) 217.xxx.xxx.xxx:500 - 206.xxx.xxx.xxx:500 10/12/22 17:22:58 ii : resend limit exceeded for phase1 exchange 10/12/22 17:22:58 ii : phase1 removal before expire time 10/12/22 17:22:58 DB : phase1 deleted ( obj count = 0 ) 10/12/22 17:22:58 ii : closed tap device tap0 10/12/22 17:22:58 DB : tunnel stats event canceled ( ref count = 1 ) 10/12/22 17:22:58 DB : removing tunnel config references 10/12/22 17:22:58 DB : removing tunnel phase2 references 10/12/22 17:22:58 DB : removing tunnel phase1 references 10/12/22 17:22:58 DB : tunnel deleted ( obj count = 0 ) 10/12/22 17:22:58 DB : removing all peer tunnel refrences 10/12/22 17:22:58 DB : peer deleted ( obj count = 0 ) 10/12/22 17:22:58 ii : ipc client process thread exit ...

  Read the article

• Why is the latency on one LVM volume consistently higher?

  - by David Schmitt

  I've got a server with LVM over RAID1. One of the volumes has a consistently higher IO latency (as measured by the diskstats_latency munin plugin) than the other volumes from the same group. As you can see, the dark orange /root volume has consistently high IO latency. Actually ten times the average latency of the physical devices. It also has the highest Min and Max values. My main concern are not the peaks, which occur under high load, but the constant load on (semi-)idle. The server is running Debian Squeeze with the VServer kernel and has four VServer containers and one KVM guest. I'm looking for ways to fix - or at least understand - this situation. Here're some parts of the system configuration: root@kvmhost2:~# df -h Filesystem Size Used Avail Use% Mounted on /dev/mapper/system--host-root 19G 3.8G 14G 22% / tmpfs 16G 0 16G 0% /lib/init/rw udev 16G 224K 16G 1% /dev tmpfs 16G 0 16G 0% /dev/shm /dev/md0 942M 37M 858M 5% /boot /dev/mapper/system--host-isos 28G 19G 8.1G 70% /srv/isos /dev/mapper/system--host-vs_a 30G 23G 6.0G 79% /var/lib/vservers/a /dev/mapper/system--host-vs_b 5.0G 594M 4.1G 13% /var/lib/vservers/b /dev/mapper/system--host-vs_c 5.0G 555M 4.2G 12% /var/lib/vservers/c /dev/loop0 4.4G 4.4G 0 100% /media/debian-6.0.0-amd64-DVD-1 /dev/loop1 4.4G 4.4G 0 100% /media/debian-6.0.0-i386-DVD-1 /dev/mapper/system--host-vs_d 74G 55G 16G 78% /var/lib/vservers/d root@kvmhost2:~# cat /proc/mounts rootfs / rootfs rw 0 0 none /sys sysfs rw,nosuid,nodev,noexec,relatime 0 0 none /proc proc rw,nosuid,nodev,noexec,relatime 0 0 none /dev devtmpfs rw,relatime,size=16500836k,nr_inodes=4125209,mode=755 0 0 none /dev/pts devpts rw,nosuid,noexec,relatime,gid=5,mode=620,ptmxmode=000 0 0 /dev/mapper/system--host-root / ext3 rw,relatime,errors=remount-ro,data=ordered 0 0 tmpfs /lib/init/rw tmpfs rw,nosuid,relatime,mode=755 0 0 tmpfs /dev/shm tmpfs rw,nosuid,nodev,relatime 0 0 fusectl /sys/fs/fuse/connections fusectl rw,relatime 0 0 /dev/md0 /boot ext3 rw,sync,relatime,errors=continue,data=ordered 0 0 /dev/mapper/system--host-isos /srv/isos ext3 rw,relatime,errors=continue,data=ordered 0 0 /dev/mapper/system--host-vs_a /var/lib/vservers/a ext3 rw,relatime,errors=continue,data=ordered 0 0 /dev/mapper/system--host-vs_b /var/lib/vservers/b ext3 rw,relatime,errors=continue,data=ordered 0 0 /dev/mapper/system--host-vs_c /var/lib/vservers/c ext3 rw,relatime,errors=continue,data=ordered 0 0 /dev/loop0 /media/debian-6.0.0-amd64-DVD-1 iso9660 ro,relatime 0 0 /dev/loop1 /media/debian-6.0.0-i386-DVD-1 iso9660 ro,relatime 0 0 /dev/mapper/system--host-vs_d /var/lib/vservers/d ext3 rw,relatime,errors=continue,data=ordered 0 0 root@kvmhost2:~# cat /proc/mdstat Personalities : [raid1] md1 : active raid1 sda2[0] sdb2[1] 975779968 blocks [2/2] [UU] md0 : active raid1 sda1[0] sdb1[1] 979840 blocks [2/2] [UU] unused devices: <none> root@kvmhost2:~# iostat -x Linux 2.6.32-5-vserver-amd64 (kvmhost2) 06/28/2012 _x86_64_ (8 CPU) avg-cpu: %user %nice %system %iowait %steal %idle 3.09 0.14 2.92 1.51 0.00 92.35 Device: rrqm/s wrqm/s r/s w/s rsec/s wsec/s avgrq-sz avgqu-sz await svctm %util sda 23.25 161.12 7.46 37.90 855.27 1596.62 54.05 0.13 2.80 1.76 8.00 sdb 22.82 161.36 7.36 37.66 850.29 1596.62 54.35 0.54 12.01 1.80 8.09 md0 0.00 0.00 0.00 0.00 0.14 0.02 38.44 0.00 0.00 0.00 0.00 md1 0.00 0.00 53.55 198.16 768.01 1585.25 9.35 0.00 0.00 0.00 0.00 dm-0 0.00 0.00 0.48 20.21 16.70 161.71 8.62 0.26 12.72 0.77 1.60 dm-1 0.00 0.00 3.62 10.03 28.94 80.21 8.00 0.19 13.68 1.59 2.17 dm-2 0.00 0.00 0.00 0.00 0.00 0.00 9.17 0.00 9.64 6.42 0.00 dm-3 0.00 0.00 6.73 0.41 53.87 3.28 8.00 0.02 3.44 0.12 0.09 dm-4 0.00 0.00 17.45 18.18 139.57 145.47 8.00 0.42 11.81 0.76 2.69 dm-5 0.00 0.00 2.50 46.38 120.50 371.07 10.06 0.69 14.20 0.46 2.26 dm-6 0.00 0.00 0.02 0.10 0.67 0.81 12.53 0.01 75.53 18.58 0.22 dm-7 0.00 0.00 0.00 0.00 0.00 0.00 7.99 0.00 11.24 9.45 0.00 dm-8 0.00 0.00 22.69 102.76 407.25 822.09 9.80 0.97 7.71 0.39 4.95 dm-9 0.00 0.00 0.06 0.08 0.50 0.62 8.00 0.07 481.23 11.72 0.16 root@kvmhost2:~# ls -l /dev/mapper/ total 0 crw------- 1 root root 10, 59 May 11 11:19 control lrwxrwxrwx 1 root root 7 Jun 5 15:08 system--host-kvm1 -> ../dm-4 lrwxrwxrwx 1 root root 7 Jun 5 15:08 system--host-kvm2 -> ../dm-3 lrwxrwxrwx 1 root root 7 Jun 5 15:06 system--host-isos -> ../dm-2 lrwxrwxrwx 1 root root 7 May 11 11:19 system--host-root -> ../dm-0 lrwxrwxrwx 1 root root 7 Jun 5 15:06 system--host-swap -> ../dm-9 lrwxrwxrwx 1 root root 7 Jun 5 15:06 system--host-vs_d -> ../dm-8 lrwxrwxrwx 1 root root 7 Jun 5 15:06 system--host-vs_b -> ../dm-6 lrwxrwxrwx 1 root root 7 Jun 5 15:06 system--host-vs_c -> ../dm-7 lrwxrwxrwx 1 root root 7 Jun 5 15:06 system--host-vs_a -> ../dm-5 lrwxrwxrwx 1 root root 7 Jun 5 15:08 system--host-kvm3 -> ../dm-1 root@kvmhost2:~#

  Read the article

• How to use Public IP in case of two ISP when two differs from each other

  - by user1471995

  Please bare with my long explanation but this is important to explain the actual problem. Please also pardon my knowledge with PFsense as i am new to this. I have single PFSense box with 3 Ethernet adapter. Before moving to configuration for these, i want to let you know i have two Ethernet based Internet Leased Line Connectivity let's call them ISP A and ISP B. Then last inetrface is LAN which is connected to network switch. Typical network diagram ISP A ----- PFSense ----> Switch ---- > Servers ISP B ----- ISP A (Initially Purchased) WAN IP:- 113.193.X.X /29 Gateway IP :- 113.193.X.A and other 4 usable public IP in same subnet(So the gateway for those IP are also same). ISP B (Recently Purchased) WAN IP:- 115.115.X.X /30 Gateway IP :- 115.115.X.B and other 5 usable public IP in different subnet(So the gateway for those IP is different), for example if 115.119.X.X2 is one of the IP from that list then the gateway for this IP is 115.119.X.X1. Configuration for 3 Interfaces Interface : WAN Network Port : nfe0 Type : Static IP Address : 113.193.X.X /29 Gateway : 113.193.X.A Interface : LAN Network Port : vr0 Type : Static IP Address : 192.168.1.1 /24 Gateway : None Interface : RELWAN Network Port : rl0 Type : Static IP Address : 115.115.X.X /30 (I am not sure of the subnet) Gateway : 115.115.X.B To use Public IP from ISP A i have done following steps a) Created Virtual IP using either ARP or IP Alias. b) Using Firewall: NAT: Port Forward i have created specific natting from one public IP to my internal Lan private IP for example :- WAN TCP/UDP * * 113.193.X.X1 53 (DNS) 192.168.1.5 53 (DNS) WAN TCP/UDP * * 113.193.X.X1 80 (HTTP) 192.168.1.5 80 (HTTP) WAN TCP * * 113.193.X.X2 80 (HTTP) 192.168.1.7 80 (HTTP) etc., c) Current state for Firewall: NAT: Outbound is Manual and whatever default rule are defined for the WAN those are only present. d) If this section in relevant then for Firewall: Rules at WAN tab then following default rule has been generated. * RFC 1918 networks * * * * * Block private networks * Reserved/not assigned by IANA * * * * * * To use Public IP from ISP B i have done following steps a) Created Virtual IP using either ARP or IP Alias. b) Using Firewall: NAT: Port Forward i have created specific natting from one public IP to my internal Lan private IP for example :- RELWAN TCP/UDP * * 115.119.116.X.X1 80 (HTTP) 192.168.1.11 80 (HTTP) c) Current state for Firewall: NAT: Outbound is Manual and whatever default rule are defined for the RELWAN those are only present. d) If this section in relevant then for Firewall: Rules at RELWAN tab then following default rule has been generated. * RFC 1918 networks * * * * * * Reserved/not assigned by IANA * * * * * * Last thing before my actual query is to make you aware that to have multiple Wan setup i have done following steps a) Under System: Gateways at Groups Tab i have created new group as following MultipleGateway WANGW, RELWAN Tier 2,Tier 1 Multiple Gateway Test b) Then Under Firewall: Rules at LAN tab i have created a rule for internal traffic as follows * LAN net * * * MultipleGateway none c) This setup works if unplug first ISP traffic start routing using ISP 2 and vice-versa. Now my main query and problem is i am not able to use public IP address allocated by ISP B, i have tried many small tweaks but not successful in anyone. The notable difference between the two ISP is a) In case of ISP A there Public usable IP address are on same subnet so the gateway used for the WAN ip is same for the other public IP address. b) In case of ISP B there public usable IP address are on different subnet so the obvious the gateway IP for them is different from WAN gateway's IP. Please let me know how to use ISP B public usable IP address, in future also i am going to rely for more IPs from ISP B only.

  Read the article

• Accessing a broken mdadm raid

  - by CarstenCarsten

  Hi! I used a western digital mybookworld (SOHO NAS storage using Linux) as backup for my Linux box. Suddenly, the mybookworld does not boot up any more. So I opened the box, removed the hard disk and put the hard disk into an external USB HDD case, and connected it to my Linux box. [ 530.640301] usb 2-1: new high speed USB device using ehci_hcd and address 3 [ 530.797630] scsi7 : usb-storage 2-1:1.0 [ 531.794844] scsi 7:0:0:0: Direct-Access WDC WD75 00AAKS-00RBA0 PQ: 0 ANSI: 2 [ 531.796490] sd 7:0:0:0: Attached scsi generic sg3 type 0 [ 531.797966] sd 7:0:0:0: [sdc] 1465149168 512-byte logical blocks: (750 GB/698 GiB) [ 531.800317] sd 7:0:0:0: [sdc] Write Protect is off [ 531.800327] sd 7:0:0:0: [sdc] Mode Sense: 38 00 00 00 [ 531.800333] sd 7:0:0:0: [sdc] Assuming drive cache: write through [ 531.803821] sd 7:0:0:0: [sdc] Assuming drive cache: write through [ 531.803836] sdc: sdc1 sdc2 sdc3 sdc4 [ 531.815831] sd 7:0:0:0: [sdc] Assuming drive cache: write through [ 531.815842] sd 7:0:0:0: [sdc] Attached SCSI disk The dmesg output looks normal, but I was wondering why the hardisk was not mounted at all. And why there are 4 different partitions on it. fdisk showed the following: root@ubuntu:/home/ubuntu# fdisk /dev/sdc WARNING: DOS-compatible mode is deprecated. It's strongly recommended to switch off the mode (command 'c') and change display units to sectors (command 'u'). Command (m for help): p Disk /dev/sdc: 750.2 GB, 750156374016 bytes 255 heads, 63 sectors/track, 91201 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00007c00 Device Boot Start End Blocks Id System /dev/sdc1 4 369 2939895 fd Linux raid autodetect /dev/sdc2 370 382 104422+ fd Linux raid autodetect /dev/sdc3 383 505 987997+ fd Linux raid autodetect /dev/sdc4 506 91201 728515620 fd Linux raid autodetect Oh no! Everything seems to be created as a mdadm software raid. Calling mdadm --examine with the different partitions seems to affirm that. I think the only partition I am interested in, is /dev/sdc4 (because it is the largest). But nevertheless I called mdadm --examine with every partition. root@ubuntu:/home/ubuntu# mdadm --examine /dev/sdc1 /dev/sdc1: Magic : a92b4efc Version : 00.90.00 UUID : 5626a2d8:070ad992:ef1c8d24:cd8e13e4 Creation Time : Wed Feb 20 00:57:49 2002 Raid Level : raid1 Used Dev Size : 2939776 (2.80 GiB 3.01 GB) Array Size : 2939776 (2.80 GiB 3.01 GB) Raid Devices : 2 Total Devices : 1 Preferred Minor : 1 Update Time : Sun Nov 21 11:05:27 2010 State : clean Active Devices : 1 Working Devices : 1 Failed Devices : 1 Spare Devices : 0 Checksum : 4c90bc55 - correct Events : 16682 Number Major Minor RaidDevice State this 0 8 1 0 active sync /dev/sda1 0 0 8 1 0 active sync /dev/sda1 1 1 0 0 1 faulty removed root@ubuntu:/home/ubuntu# mdadm --examine /dev/sdc2 /dev/sdc2: Magic : a92b4efc Version : 00.90.00 UUID : 9734b3ee:2d5af206:05fe3413:585f7f26 Creation Time : Wed Feb 20 00:57:54 2002 Raid Level : raid1 Used Dev Size : 104320 (101.89 MiB 106.82 MB) Array Size : 104320 (101.89 MiB 106.82 MB) Raid Devices : 2 Total Devices : 1 Preferred Minor : 2 Update Time : Wed Oct 27 20:19:08 2010 State : clean Active Devices : 1 Working Devices : 1 Failed Devices : 1 Spare Devices : 0 Checksum : 55560b40 - correct Events : 9884 Number Major Minor RaidDevice State this 0 8 2 0 active sync /dev/sda2 0 0 8 2 0 active sync /dev/sda2 1 1 0 0 1 faulty removed root@ubuntu:/home/ubuntu# mdadm --examine /dev/sdc3 /dev/sdc3: Magic : a92b4efc Version : 00.90.00 UUID : 08f30b4f:91cca15d:2332bfef:48e67824 Creation Time : Wed Feb 20 00:57:54 2002 Raid Level : raid1 Used Dev Size : 987904 (964.91 MiB 1011.61 MB) Array Size : 987904 (964.91 MiB 1011.61 MB) Raid Devices : 2 Total Devices : 1 Preferred Minor : 3 Update Time : Sun Nov 21 11:05:27 2010 State : clean Active Devices : 1 Working Devices : 1 Failed Devices : 1 Spare Devices : 0 Checksum : 39717874 - correct Events : 73678 Number Major Minor RaidDevice State this 0 8 3 0 active sync 0 0 8 3 0 active sync 1 1 0 0 1 faulty removed root@ubuntu:/home/ubuntu# mdadm --examine /dev/sdc4 /dev/sdc4: Magic : a92b4efc Version : 00.90.00 UUID : febb75ca:e9d1ce18:f14cc006:f759419a Creation Time : Wed Feb 20 00:57:55 2002 Raid Level : raid1 Used Dev Size : 728515520 (694.77 GiB 746.00 GB) Array Size : 728515520 (694.77 GiB 746.00 GB) Raid Devices : 2 Total Devices : 1 Preferred Minor : 4 Update Time : Sun Nov 21 11:05:27 2010 State : clean Active Devices : 1 Working Devices : 1 Failed Devices : 1 Spare Devices : 0 Checksum : 2f36a392 - correct Events : 519320 Number Major Minor RaidDevice State this 0 8 4 0 active sync 0 0 8 4 0 active sync 1 1 0 0 1 faulty removed If I read the output correctly everything was removed, because it was faulty. Is there ANY way to see the contents of the largest partition? Or seeing somehow which files are broken? I see that everything is raid1 which is only mirroring, so this should be a normal partition. I am anxious to do anything with mdadm, in fear that I destroy the data on the hard disk. I would be very thankful for any help.

  Read the article

• Sharepoint web services -- The HTTP request is unauthorized with client authentication scheme 'Ntlm'

  - by Pandincus

  I know there's a lot of questions on SO similar to this, but I couldn't find one for this particular issue. A couple of points, first: I have no control over our Sharepoint server. I cannot tweak any IIS settings. I believe our IIS server version is IIS 7.0. Our Sharepoint Server is anticipating requests via NTLM. Our Sharepoint Server is on the same domain as my client computer. I am using .NET Framework 3.5, Visual Studio 2008 I am trying to write a simple console app to manipulate Sharepoint data using Sharepoint Web Services. I have added the Service Reference, and the following is my app.config: <system.serviceModel> <bindings> <basicHttpBinding> <binding name="ListsSoap" closeTimeout="00:01:00" openTimeout="00:01:00" receiveTimeout="00:10:00" sendTimeout="00:01:00" allowCookies="false" bypassProxyOnLocal="false" hostNameComparisonMode="StrongWildcard" maxBufferSize="65536" maxBufferPoolSize="524288" maxReceivedMessageSize="65536" messageEncoding="Text" textEncoding="utf-8" transferMode="Buffered" useDefaultWebProxy="true"> <readerQuotas maxDepth="32" maxStringContentLength="8192" maxArrayLength="16384" maxBytesPerRead="4096" maxNameTableCharCount="16384" /> <security mode="Transport"> <transport clientCredentialType="Ntlm" proxyCredentialType="Ntlm" /> </security> </binding> </basicHttpBinding> </bindings> <client> <endpoint address="https://subdomain.companysite.com/subsite/_vti_bin/Lists.asmx" binding="basicHttpBinding" bindingConfiguration="ListsSoap" contract="ServiceReference1.ListsSoap" name="ListsSoap" /> </client> </system.serviceModel> This is my code: static void Main(string[] args) { using (var client = new ListsSoapClient()) { client.ClientCredentials.Windows.ClientCredential = new NetworkCredential("username", "password", "domain"); client.GetListCollection(); } } When I call GetListCollection(), the following MessageSecurityException gets thrown: The HTTP request is unauthorized with client authentication scheme 'Ntlm'. The authentication header received from the server was 'NTLM'. With an inner WebException: "The remote server returned an error: (401) Unauthorized." I've tried various bindings and various code tweaks to try to authenticate properly, but to no avail. I'll list those below. I've tried the following steps: Using a native Win32 Impersonator before creating the client using (new Impersonator.Impersonator("username", "password", "domain")) using (var client = new ListsSoapClient()) { client.ClientCredentials.Windows.ClientCredential = new NetworkCredential("dpincas", "password", "domain"); client.GetListCollection(); } This produced the same error message. Setting TokenImpersonationLevel for my client credentials using (var client = new ListsSoapClient()) { client.ClientCredentials.Windows.AllowedImpersonationLevel = TokenImpersonationLevel.Impersonation; client.GetListCollection(); } This produced the same error message. Using security mode=TransportCredentialOnly <security mode="TransportCredentialOnly"> <transport clientCredentialType="Ntlm" /> </security> This resulted in a different error message: The provided URI scheme 'https' is invalid; expected 'http'. Parameter name: via However, I need to use https, so I cannot change my URI scheme. I've tried some other combinations that I can't remember, but I'll post them when I do. I'm really at wits end here. I see a lot of links on Google that say "switch to Kerberos", but my server seems to only be accepting NTLM, not "Negotiate" (as it would say if it was looking for Kerberos), so that is unfortunately not an option. Any help out there, folks?

  Read the article

• Visual Studio 2010 and javascript debugging in external javascript files (embedded and minified).

  - by OKB

  Hi, The asp.net web application I'm working on is written in asp.net 3.5, the web app solution is upgraded from VS 2008 (don't know if that matter). The solution had javascript in the aspx files before I moved the javascript to external files. Now what I have done is to set all the javascript files to be embedded resource (except the jquery.js file) and I want to minify them when building for release by using the MS Ajax Minifier. I want to use the minified javascript files when I'm in the RELEASE mode and when I'm in DEBUG mode I want to use the "normal" versions. My problem now is that I'm unable to debug the javascript code in debug mode. When I set a break point a javascript function, VS is not breaking at all when the function is executed. I have added this entry in my web.config: <system.web> <compilation defaultLanguage="c#" debug="true" /> </system.web> Here how I register the jquery in an aspx-file: <asp:ScriptManagerProxy ID="ScriptManagerProxy1" runat="server"> <Scripts> <asp:ScriptReference Path="~/Javascript/jquery.js"/> </Scripts> </asp:ScriptManagerProxy> External javascript registration in the code-behind: #if DEBUG [assembly: WebResource("braArkivWeb.Javascript.jquery.js", "text/javascript")] [assembly: WebResource(braArkivWeb.ArkivdelSearch.JavaScriptResource, "text/javascript")] #else [assembly: WebResource("braArkivWeb.Javascript.jquery.min.js", "text/javascript")] [assembly: WebResource(braArkivWeb.ArkivdelSearch.JavaScriptMinResource, "text/javascript")] #endif public partial class ArkivdelSearch : Page { public const string JavaScriptResource = "braArkivWeb.ArkivdelSearch.js"; public const string JavaScriptMinResource = "braArkivWeb.ArkivdelSearch.min.js"; protected void Page_Init(object sender, EventArgs e) { InitPageClientScript(); } private void InitPageClientScript() { #if DEBUG this.Page.ClientScript.RegisterClientScriptResource(typeof(ArkivdelSearch), "braArkivWeb.Javascript.jquery.js"); this.Page.ClientScript.RegisterClientScriptResource(typeof(ArkivdelSearch), JavaScriptResource); #else this.Page.ClientScript.RegisterClientScriptResource(typeof(ArkivdelSearch), "braArkivWeb.Javascript.jquery.min.js"); this.Page.ClientScript.RegisterClientScriptResource(typeof(ArkivdelSearch), JavaScriptMinResource); #endif StringBuilder sb = new StringBuilder(); Page.ClientScript.RegisterStartupScript(typeof(ArkivdelSearch), "initArkivdelSearch", sb.ToString(), true); } } In the project file I have added this code to minify the javascripts: <!-- Minify all JavaScript files that were embedded as resources --> <UsingTask TaskName="AjaxMin" AssemblyFile="$(MSBuildProjectDirectory)\..\..\SharedLib\AjaxMinTask.dll" /> <PropertyGroup> <ResGenDependsOn> MinifyJavaScript; $(ResGenDependsOn) </ResGenDependsOn> </PropertyGroup> <Target Name="MinifyJavaScript" Condition=" '$(ConfigurationName)'=='Release' "> <Copy SourceFiles="@(EmbeddedResource)" DestinationFolder="$(IntermediateOutputPath)" Condition="'%(Extension)'=='.js'"> <Output TaskParameter="DestinationFiles" ItemName="EmbeddedJavaScriptResource" /> </Copy> <AjaxMin JsSourceFiles="@(EmbeddedJavaScriptResource)" JsSourceExtensionPattern="\.js$" JsTargetExtension=".js" /> <ItemGroup> <EmbeddedResource Remove="@(EmbeddedResource)" Condition="'%(Extension)'=='.js'" /> <EmbeddedResource Include="@(EmbeddedJavaScriptResource)" /> <FileWrites Include="@(EmbeddedJavaScriptResource)" /> </ItemGroup> </Target> Do you see what I'm doing wrong? Or what I'm missing in order to be able to debug my javascript code? Best Regards, OKB

  Read the article

• Partial Trust in WPF 4

  - by Hadi Eskandari

  I've started a new project in WPF 4 (.NET 4) and trying to see if I can run it in xbap mode. I need to run the application in Full Trust with the new mode made available in .NET 4 which asks the end user if the full trust application should be run. I've set the "Security" mode to "Full Trust" application, and it builds just fine. When I run it, an exception is thrown and IE error message shows the following error. Any ways around it?? Startup URI: T:\projects\Hightech Sources\PayRoll\PayRoll.Web\publish\PayRoll.Web.xbap Application Identity: file:///T:/projects/Hightech%20Sources/PayRoll/PayRoll.Web/publish/PayRoll.Web.xbap#PayRoll.Web.xbap, Version=1.0.0.0, Culture=neutral, PublicKeyToken=1d910f49755d2c97, processorArchitecture=msil/PayRoll.Web.exe, Version=1.0.0.0, Culture=neutral, PublicKeyToken=1d910f49755d2c97, processorArchitecture=msil, type=win32 System.Security.SecurityException: Request for the permission of type 'System.Security.Permissions.FileIOPermission, mscorlib, Version=4.0.0.0, Culture=neutral, PublicKeyToken=b77a5c561934e089' failed. at System.Security.CodeAccessSecurityEngine.Check(Object demand, StackCrawlMark& stackMark, Boolean isPermSet) at System.Security.CodeAccessSecurityEngine.Check(CodeAccessPermission cap, StackCrawlMark& stackMark) at System.Security.CodeAccessPermission.Demand() at System.Reflection.RuntimeAssembly.InternalLoadAssemblyName(AssemblyName assemblyRef, Evidence assemblySecurity, StackCrawlMark& stackMark, Boolean forIntrospection, Boolean suppressSecurityChecks) at System.Reflection.RuntimeAssembly.InternalLoadFrom(String assemblyFile, Evidence securityEvidence, Byte[] hashValue, AssemblyHashAlgorithm hashAlgorithm, Boolean forIntrospection, Boolean suppressSecurityChecks, StackCrawlMark& stackMark) at System.Reflection.Assembly.LoadFrom(String assemblyFile) at PayRoll.Web.App.SelectAssemblies() at Caliburn.PresentationFramework.ApplicationModel.CaliburnApplication..ctor() at PayRoll.Web.App..ctor() at PayRoll.Web.App.Main() at System.AppDomain._nExecuteAssembly(RuntimeAssembly assembly, String[] args) at System.AppDomain.nExecuteAssembly(RuntimeAssembly assembly, String[] args) at System.Runtime.Hosting.ManifestRunner.Run(Boolean checkAptModel) at System.Runtime.Hosting.ManifestRunner.ExecuteAsAssembly() at System.Runtime.Hosting.ApplicationActivator.CreateInstance(ActivationContext activationContext, String[] activationCustomData) at System.Runtime.Hosting.ApplicationActivator.CreateInstance(ActivationContext activationContext) at System.Windows.Interop.PresentationApplicationActivator.CreateInstance(ActivationContext actCtx) at System.Activator.CreateInstance(ActivationContext activationContext) at System.AppDomain.Setup(Object arg) at System.AppDomain.nCreateInstance(String friendlyName, AppDomainSetup setup, Evidence providedSecurityInfo, Evidence creatorsSecurityInfo, IntPtr parentSecurityDescriptor) at System.Runtime.Hosting.ApplicationActivator.CreateInstanceHelper(AppDomainSetup adSetup) at System.Runtime.Hosting.ApplicationActivator.CreateInstance(ActivationContext activationContext, String[] activationCustomData) at System.Windows.Interop.PresentationApplicationActivator.CreateInstance(ActivationContext actCtx) at System.Activator.CreateInstance(ActivationContext activationContext) at System.Deployment.Application.DeploymentManager.ExecuteNewDomain() at System.Deployment.Application.InPlaceHostingManager.Execute() at MS.Internal.AppModel.XappLauncherApp.ExecuteDownloadedApplication() at System.Windows.Interop.DocObjHost.RunApplication(ApplicationRunner runner) at MS.Internal.AppModel.XappLauncherApp.XappLauncherApp_Exit(Object sender, ExitEventArgs e) at System.Windows.Application.OnExit(ExitEventArgs e) at System.Windows.Application.DoShutdown() at System.Windows.Application.ShutdownImpl() at System.Windows.Application.ShutdownCallback(Object arg) at System.Windows.Threading.ExceptionWrapper.InternalRealCall(Delegate callback, Object args, Int32 numArgs) at MS.Internal.Threading.ExceptionFilterHelper.TryCatchWhen(Object source, Delegate method, Object args, Int32 numArgs, Delegate catchHandler) at System.Windows.Threading.DispatcherOperation.InvokeImpl() at System.Windows.Threading.DispatcherOperation.InvokeInSecurityContext(Object state) at System.Threading.ExecutionContext.runTryCode(Object userData) at System.Runtime.CompilerServices.RuntimeHelpers.ExecuteCodeWithGuaranteedCleanup(TryCode code, CleanupCode backoutCode, Object userData) at System.Threading.ExecutionContext.RunInternal(ExecutionContext executionContext, ContextCallback callback, Object state) at System.Threading.ExecutionContext.Run(ExecutionContext executionContext, ContextCallback callback, Object state, Boolean ignoreSyncCtx) at System.Threading.ExecutionContext.Run(ExecutionContext executionContext, ContextCallback callback, Object state) at System.Windows.Threading.DispatcherOperation.Invoke() at System.Windows.Threading.Dispatcher.ProcessQueue() at System.Windows.Threading.Dispatcher.WndProcHook(IntPtr hwnd, Int32 msg, IntPtr wParam, IntPtr lParam, Boolean& handled) at MS.Win32.HwndWrapper.WndProc(IntPtr hwnd, Int32 msg, IntPtr wParam, IntPtr lParam, Boolean& handled) at MS.Win32.HwndSubclass.DispatcherCallbackOperation(Object o) at System.Windows.Threading.ExceptionWrapper.InternalRealCall(Delegate callback, Object args, Int32 numArgs) at MS.Internal.Threading.ExceptionFilterHelper.TryCatchWhen(Object source, Delegate method, Object args, Int32 numArgs, Delegate catchHandler) at System.Windows.Threading.Dispatcher.InvokeImpl(DispatcherPriority priority, TimeSpan timeout, Delegate method, Object args, Int32 numArgs) at MS.Win32.HwndSubclass.SubclassWndProc(IntPtr hwnd, Int32 msg, IntPtr wParam, IntPtr lParam) at MS.Win32.UnsafeNativeMethods.DispatchMessage(MSG& msg) at System.Windows.Threading.Dispatcher.PushFrameImpl(DispatcherFrame frame) at System.Windows.Threading.Dispatcher.PushFrame(DispatcherFrame frame) at System.Windows.Threading.Dispatcher.Run() at System.Windows.Application.RunDispatcher(Object ignore) at System.Windows.Application.StartDispatcherInBrowser(Object unused) at System.Windows.Threading.ExceptionWrapper.InternalRealCall(Delegate callback, Object args, Int32 numArgs) at MS.Internal.Threading.ExceptionFilterHelper.TryCatchWhen(Object source, Delegate method, Object args, Int32 numArgs, Delegate catchHandler) at System.Windows.Threading.DispatcherOperation.InvokeImpl() at System.Windows.Threading.DispatcherOperation.InvokeInSecurityContext(Object state) at System.Threading.ExecutionContext.runTryCode(Object userData) at System.Runtime.CompilerServices.RuntimeHelpers.ExecuteCodeWithGuaranteedCleanup(TryCode code, CleanupCode backoutCode, Object userData) at System.Threading.ExecutionContext.RunInternal(ExecutionContext executionContext, ContextCallback callback, Object state) at System.Threading.ExecutionContext.Run(ExecutionContext executionContext, ContextCallback callback, Object state, Boolean ignoreSyncCtx) at System.Threading.ExecutionContext.Run(ExecutionContext executionContext, ContextCallback callback, Object state) at System.Windows.Threading.DispatcherOperation.Invoke() at System.Windows.Threading.Dispatcher.ProcessQueue() at System.Windows.Threading.Dispatcher.WndProcHook(IntPtr hwnd, Int32 msg, IntPtr wParam, IntPtr lParam, Boolean& handled) at MS.Win32.HwndWrapper.WndProc(IntPtr hwnd, Int32 msg, IntPtr wParam, IntPtr lParam, Boolean& handled) at MS.Win32.HwndSubclass.DispatcherCallbackOperation(Object o) at System.Windows.Threading.ExceptionWrapper.InternalRealCall(Delegate callback, Object args, Int32 numArgs) at MS.Internal.Threading.ExceptionFilterHelper.TryCatchWhen(Object source, Delegate method, Object args, Int32 numArgs, Delegate catchHandler) at System.Windows.Threading.Dispatcher.InvokeImpl(DispatcherPriority priority, TimeSpan timeout, Delegate method, Object args, Int32 numArgs) at MS.Win32.HwndSubclass.SubclassWndProc(IntPtr hwnd, Int32 msg, IntPtr wParam, IntPtr lParam) The action that failed was: Demand The type of the first permission that failed was: System.Security.Permissions.FileIOPermission

  Read the article

• Treeview - Hierarchical Data Template - Binding does not update on source change?

  - by ClearsTheScreen

  Greetings! I ran into this problem in my project (Silverlight 3 with C#): I have a TreeView which is data bound to, well, a tree. This TreeView has a HierarchicalDataTamplate in a resource dictionary, that defines various controls. Now I want to hide (Visibility.Collapse) some items depending on wether a node has children or not. Other items shall be visible under the same condition. It works like charm when I first bind the source tree to the TreeView, but when I change the source tree, the visibility in the treeview does not change. XAML - page: <controls:TreeView x:Name="SankeyTreeView" ItemContainerStyle="{StaticResource expandedTreeViewItemStyle}" ItemTemplate="{StaticResource SankeyTreeTemplate}"> <controls:TreeViewItem IsExpanded="True"> <controls:TreeViewItem.HeaderTemplate> <DataTemplate> <TextBlock Text="This is just for loading and will be replaced directly after the data becomes available..."/> </DataTemplate> </controls:TreeViewItem.HeaderTemplate> </controls:TreeViewItem> </controls:TreeView> XAML - ResourceDictionary <!-- Each node in the tree is structurally identical, hence only one Hierarchical Data Template that'll use itself on the children. --> <Data:HierarchicalDataTemplate x:Key="SankeyTreeTemplate" ItemsSource="{Binding Children}"> <Grid Height="24"> <TextBlock x:Name="TextBlockName" Text="{Binding Path=Value.name, Mode=TwoWay}" VerticalAlignment="Center" Foreground="Black"/> <TextBox x:Name="TextBoxFlow" Text="{Binding Path=Value.flow, Mode=TwoWay}" Grid.Column="1" Visibility="{Binding Children, Converter={StaticResource BoxConverter}, ConverterParameter=\{box\}}"/> <TextBlock x:Name="TextBlockThroughput" Text="{Binding Path=Value.throughput, Mode=TwoWay}" Grid.Column="1" Visibility="{Binding Children, Converter={StaticResource BoxConverter}, ConverterParameter=\{block\}}"/> <Button x:Name="ButtonAddNode"/> <Button x:Name="ButtonDeleteNode"/> <Button x:Name="ButtonEditNode"/> </Grid> </Data:HierarchicalDataTemplate> Now, as you can see, the TextBoxFlow and the TextBlockThroughput share the same space. What I aim at: The "Throughput" value of a node is how much of something 'flows' through this node from its children. It can't be changed directly, so I want to display a text block. Only leaf nodes have a TextBox to let someone enter the 'flow' that is generated in this leaf node. (I.E.: Node.Throughput = Node.Flow + Sum(Children.Throughput), where Node.Flow = 0 for each non-leaf.) What the BoxConverter (silly name -.-) does: public object Convert(object value, Type targetType, object parameter, System.Globalization.CultureInfo culture) { if ((value as NodeList<TreeItem>).Count > 1) // Node has Children? { if ((parameter as String) == "{box}") { return Visibility.Collapsed; } else ((parameter as String) == "{block}") { return Visibility.Visible; } } else { /* * As above, just with Collapsed and Visible switched */ } } The structure of the tree that is bound to the TreeView is essentially stolen from Dan Vanderboom (a bit too much to dump the whole code here), except that I here of course use an ObservableCollection for the children and the value items implement INotifyPropertyChanged. I would be very grateful if someone could explain to me, why inserting items into the underlying tree does not update the visibility for box and block. Thank you in advance!

  Read the article

• How to fix notifyDataSetChanged/ListView problems in dynamic Adapter wrapper Android

  - by ipaterson

  Summary: Trying to dynamically add heading rows to a ListView via a custom adapter wrapper. ListView is having trouble keeping the scroll position in sync. Runnable demo project provided. I would like to dynamically add items to a list based on the values in a CursorAdapter, several positions ahead of what the user is currently viewing. To do this, I have an adapter that wraps the CursorAdapter and keeps the new content indexed in a SparseArray. The ListView needs to be updated when items are added to the custom adapter, but I have met a lot of pitfalls trying to get that to work and would love some advice. The demo project can be downloaded here: http://dl.dropbox.com/u/15334423/DynamicSectionedList.zip In the demo, the headings are added dynamically by looking ahead 10 places to find the correct position where the list items switch to the next letter. Each implementation of notifyDataSetChanged has problems as described: Demo 1 This demo shows the importance of notifyDataSetChanged(). On clicking anything, the app will crash. This is due to some sanity checking in ListView... mItemCount != adapter.getItemCount(). Moral is, we need to notify the list that data has changed. Demo 2 The natural next step is to notify the ListView of changes when changes occur. Unfortunately, doing so while the ListView is scrolling firmly breaks all touch interaction until the app switches out of touch mode. You will need to "fling scroll" far enough to generate new headings in order to notice this. Tapping the screen will not cause the scroll to stop, and once stopped none of the list items will be clickable. This is due to some if (!mDataChanged) { /* do very important stuff */ } code in AbsListView.onTouchEvent(). Demo 3 To fix this, Demo 3 introduces a pendingChanges flag and the custom Adapter gains a notifyDataSetChangedIfNeeded() which can be called by the ListView once it has entered a "safe" state for changes. The first point where changes must be notified is in ListView.layoutChildren(), so I overrode that method to first notify of changes if needed, then call through. Fling past at least one heading then click a list item. This doesn't quite work right, though I'm not totally sure why. Tapping or selecting an item with the keyboard/trackball causes the list to refresh without properly syncing the old position. It scrolls to the top of the list which is not acceptable. Demo 4 The scroll problem in Demo 3 can be conquered, at least in touch mode. By adding a call to notifyDataSetChangedIfNeeded() on touch down, the data change happens to take place at such a time that all touch interaction works as expected and the list position is properly synced. However, I can't find an analog for that when the device is not in touch mode, not to mention the fact that it definitely seems like a hack. The list almost always scrolls back to the top, I can't find out what causes it to occasionally maintain the correct position. Since Android is fighting me at each step of the way, I feel like there should be a better approach. Please try the demo, if any fixes can be applied to get it working that would be great! Many thanks to anyone who can look into this, hopefully if we can get the code working it will be useful for others trying to accomplish the same optimization for lists with headings.

  Read the article

• ssh permission denied

  - by Gitmo

  I am trying to ssh into a remote machine and I get the following debug messages: debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for * debug2: ssh_connect: needpriv 0 debug1: Connecting to xxx.xxx.x.xx [xxx.xxx.xx.x] port 22. debug1: Connection established. debug3: Not a RSA1 key file /home/hadoop/.ssh/id_rsa. debug2: key_type_from_name: unknown key type '-----BEGIN' debug3: key_read: missing keytype debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug2: key_type_from_name: unknown key type '-----END' debug3: key_read: missing keytype debug1: identity file /home/hadoop/.ssh/id_rsa type 1 debug1: Checking blacklist file /usr/share/ssh/blacklist.RSA-2048 debug1: Checking blacklist file /etc/ssh/blacklist.RSA-2048 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.1p1 Debian-6ubuntu2 debug1: match: OpenSSH_5.1p1 Debian-6ubuntu2 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.1p1 Debian-6ubuntu2 debug2: fd 3 setting O_NONBLOCK debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug2: kex_parse_kexinit: diffie-hellman-group-exchange-sha256,diffie-hellman-group-exchange-sha1,diffie-hellman-group14-sha1,diffie-hellman-group1-sha1 debug2: kex_parse_kexinit: ssh-rsa,ssh-dss debug2: kex_parse_kexinit: aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,arcfour128,arcfour256,arcfour,aes192-cbc,aes256-cbc,[email protected],aes128-ctr,aes192-ctr,aes256-ctr debug2: kex_parse_kexinit: aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,arcfour128,arcfour256,arcfour,aes192-cbc,aes256-cbc,[email protected],aes128-ctr,aes192-ctr,aes256-ctr debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: none,[email protected],zlib debug2: kex_parse_kexinit: none,[email protected],zlib debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: first_kex_follows 0 debug2: kex_parse_kexinit: reserved 0 debug2: kex_parse_kexinit: diffie-hellman-group-exchange-sha256,diffie-hellman-group-exchange-sha1,diffie-hellman-group14-sha1,diffie-hellman-group1-sha1 debug2: kex_parse_kexinit: ssh-rsa,ssh-dss debug2: kex_parse_kexinit: aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,arcfour128,arcfour256,arcfour,aes192-cbc,aes256-cbc,[email protected],aes128-ctr,aes192-ctr,aes256-ctr debug2: kex_parse_kexinit: aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,arcfour128,arcfour256,arcfour,aes192-cbc,aes256-cbc,[email protected],aes128-ctr,aes192-ctr,aes256-ctr debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: none,[email protected] debug2: kex_parse_kexinit: none,[email protected] debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: first_kex_follows 0 debug2: kex_parse_kexinit: reserved 0 debug2: mac_setup: found hmac-md5 debug1: kex: server->client aes128-cbc hmac-md5 none debug2: mac_setup: found hmac-md5 debug1: kex: client->server aes128-cbc hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug2: dh_gen_key: priv key bits set: 128/256 debug2: bits set: 511/1024 debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug3: check_host_in_hostfile: filename /home/hadoop/.ssh/known_hosts debug3: check_host_in_hostfile: match line 20 debug1: Host '192.168.1.63' is known and matches the RSA host key. debug1: Found key in /home/hadoop/.ssh/known_hosts:20 debug2: bits set: 511/1024 debug1: ssh_rsa_verify: signature correct debug2: kex_derive_keys debug2: set_newkeys: mode 1 debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug2: set_newkeys: mode 0 debug1: SSH2_MSG_NEWKEYS received debug1: SSH2_MSG_SERVICE_REQUEST sent debug2: service_accept: ssh-userauth debug1: SSH2_MSG_SERVICE_ACCEPT received debug2: key: /home/hadoop/.ssh/id_rsa (0x241c110) debug1: Authentications that can continue: publickey,password debug3: start over, passed a different list publickey,password debug3: preferred gssapi-keyex,gssapi-with-mic,gssapi,publickey,keyboard-interactive debug3: authmethod_lookup publickey debug3: remaining preferred: keyboard-interactive debug3: authmethod_is_enabled publickey debug1: Next authentication method: publickey debug1: Offering public key: /home/hadoop/.ssh/id_rsa debug3: send_pubkey_test debug2: we sent a publickey packet, wait for reply debug1: Authentications that can continue: publickey,password debug2: we did not send a packet, disable method debug1: No more authentication methods to try. Permission denied (publickey,password). What seems to be the problem?? I have tried everything, this is driving me nuts.

  Read the article

• What is the cause of exception in wcf peer-to-peer service with callbacks ?

  - by miensol

  I've been playing around with WCF peer to peer, one way operation contract and callbacks. I have a following service: [ServiceContract(CallbackContract = typeof(ICodeFoundCallback))] public interface ICodeSearch { [OperationContract(IsOneWay = true)] void Search(string searchQuery); } public interface ICodeFoundCallback { [OperationContract(IsOneWay = true)] void Found(string found); } public class CodeSearchService : ServiceWithCallback<ICodeFoundCallback>, ICodeSearch { public void Search(string searchQuery) { Console.WriteLine("Searching for :" + searchQuery); Callback(t=> t.Found(searchQuery)); } } public class ServiceWithCallback<T> { protected void Callback(Action<T> call) { var callbackChanel = OperationContext.Current.GetCallbackChannel<T>(); call(callbackChanel); } } with such config on server <system.serviceModel> <services> <service name="CodeSearch.Service.CodeSearchService" behaviorConfiguration="CodeSearchServiceBehavior"> <host> <baseAddresses> <add baseAddress="net.p2p://CodeSearchService"/> </baseAddresses> </host> <endpoint name="CodeSearchServiceEndpoint" address="" binding="netPeerTcpBinding" bindingConfiguration="BindingUnsecure" contract="CodeSearch.Service.ICodeSearch" /> </service> </services> <behaviors> <serviceBehaviors> <behavior name="CodeSearchServiceBehavior"> <serviceMetadata /> </behavior> </serviceBehaviors> </behaviors> <bindings> <netPeerTcpBinding> <binding name="BindingUnsecure"> <security mode="None"/> <resolver mode="Pnrp"/> </binding> </netPeerTcpBinding> <customBinding> <binding name="CodeSearchServiceEndpoint"> <binaryMessageEncoding maxReadPoolSize="64" maxWritePoolSize="16" maxSessionSize="2048"> <readerQuotas maxDepth="32" maxStringContentLength="8192" maxArrayLength="16384" maxBytesPerRead="4096" maxNameTableCharCount="16384" /> </binaryMessageEncoding> <peerTransport maxBufferPoolSize="524288" maxReceivedMessageSize="65536" port="0"> <security mode="None" /> </peerTransport> </binding> </customBinding> </bindings> <system.serviceModel> And simple client generated by Visual studio tooling. When I run two or more servers, and client invokes Search method: search method is called on each server first server calls client callback properly second server throws ArgumentException "A property with the name 'TransactionFlowProperty' already exists" when invoking client callback (Found method) I've no idea what is going on since as far as I know transaction flow is by default set to none. Could anyone help me solve this issue ?

  Read the article

• Link Error : xxx is already defined in *****.LIB :: What exactly is wrong?

  - by claws

  Problem: I'm trying to use a library named DCMTK which used some other external libraries ( zlib, libtiff, libpng, libxml2, libiconv ). I've downloaded these external libraries (*.LIB & *.h files ) from the same website. Now, when I compile the DCMTK library I'm getting link errors (793 errors) like this: Error 2 error LNK2005: __encode_pointer already defined in MSVCRTD.lib(MSVCR90D.dll) LIBCMTD.lib dcmmkdir Error 3 error LNK2005: __decode_pointer already defined in MSVCRTD.lib(MSVCR90D.dll) LIBCMTD.lib dcmmkdir Error 4 error LNK2005: __CrtSetCheckCount already defined in MSVCRTD.lib(MSVCR90D.dll) LIBCMTD.lib dcmmkdir Error 5 error LNK2005: __invoke_watson already defined in MSVCRTD.lib(MSVCR90D.dll) LIBCMTD.lib dcmmkdir Error 6 error LNK2005: __errno already defined in MSVCRTD.lib(MSVCR90D.dll) LIBCMTD.lib dcmmkdir Error 7 error LNK2005: __configthreadlocale already defined in MSVCRTD.lib(MSVCR90D.dll) LIBCMTD.lib dcmmkdir Error 8 error LNK2005: _exit already defined in MSVCRTD.lib(MSVCR90D.dll) LIBCMTD.lib dcmmkdir Documentation: This seems to be a popular error for this library so, they do have a FAQ entry addressing this issue which ( http://forum.dcmtk.org/viewtopic.php?t=35 ) says: The problem is that the linker tries to combine different, incompatible versions of the Visual C++ runtime library into a single binary. This happens when not all parts of your project and the libraries you link against are generated with the same code generation options in Visual C++. Do not use the /NODEFAULTLIB workaround, because strange software crashes may follow. Fix the problem! DCMTK is by default compiled with the "Multithreaded" or "Multithreaded Debug" code generation option (the latter for Debug mode). Either change the project settings of all of your code to use these code generation options, or change the code generation for all DCMTK modules and re-compile. MFC users beware: DCMTK should be compiled with "Multithreaded DLL" or "Multithreaded DLL Debug" settings if you want to link the libraries into an MFC application. Solution to same problem for others: http://stackoverflow.com/questions/2259697/vscopengl-huge-amount-of-linker-issues-with-release-build-only says: It seems that your release build is trying to link to something that was built debug. You probably have a broken dependency in your build, (or you missed rebuilding something to release by hand if your project is normally built in pieces). More technically, you seem to be linking projects built with different C Run Time library settings, one with "Multi-Threaded", another one with "Multi-Threaded Debug". Adjust the settings for all the projects to use the very same flavour of the library and the issue should go away Questions: Till now I used to think that Name mangling is the only problem that may cause linking failures if its not been standardized. Just now I knew there are other things also which can cause same effect. Whats up with the "Debug Mode" (Multi-Threaded Debug) and "Release Mode" (Multi-Threaded)? What exactly is happening under the hood? Why exactly this thing is causing linking error? I wonder if there is something called "Single-Threaded Debug" and "Single-Threaded" which again causes the same thing. Documentation talks something about "Code Generation Options". What Code Generation Options? WTH are they? Documentation specifically warns us not to use /NODEFAULTLIB workaround. (example /NODEFAULTLIB :msvcrt ). Why? How would I cause troubles? what exactly is it? Please explain the last point in the documentation for MFC users. Because I'm going to use MFC later in this project. Explain Why should we do it? What troubles would it cause if I don't. Anything more you'd like to mention? I mean regarding similar errors. I'm very interested in Linker & its problems. So, if there are any similar things you can mentions them or some keywords atleast.

  Read the article

• Transport Security with Certificate Authentication

  - by Brian T

  I'm getting the following error when I access my webservice localhost/MyService/MyService.svc The SSL settings for the service 'SslRequireCert' does not match those of the IIS 'Ssl, SslNegotiateCert'. I've following the web.config examples as specified in http://msdn.microsoft.com/en-us/library/ms731074.aspx Here is my wcf server web.config: <?xml version="1.0" encoding="UTF-8"?> <configuration xmlns="http://schemas.microsoft.com/.NetConfiguration/v2.0"> <appSettings /> <system.web> <identity impersonate="false" /> <roleManager enabled="true" /> <authentication mode="Windows" /> <customErrors mode="Off" /> <webServices> <protocols> <add name="HttpGet" /> <add name="HttpPost" /> </protocols> </webServices> </system.web> <system.webServer> <directoryBrowse enabled="true" /> <validation validateIntegratedModeConfiguration="false" /> <security> <authorization> <remove users="*" roles="" verbs="" /> <add accessType="Allow" users="*" roles="" /> </authorization> </security> </system.webServer> <system.serviceModel> <services> <service name="AspNetSqlProviderService" behaviorConfiguration="MyServiceBehavior"> <endpoint binding="wsHttpBinding" contract="Interface1" bindingConfiguration="CertificateWithTransportWSHttpBinding" /> <endpoint binding="wsHttpBinding" contract="Interface2" bindingConfiguration="CertificateWithTransportWSHttpBinding" /> <endpoint address="mex" binding="wsHttpBinding" bindingConfiguration="CertificateWithTransportWSHttpBinding" name="Metadata_Exchange" contract="IMetadataExchange" /> </service> </services> <behaviors> <serviceBehaviors> <behavior name="MyServiceBehavior"> <serviceDebug includeExceptionDetailInFaults="True" /> <serviceMetadata /> <serviceCredentials> <clientCertificate> <authentication trustedStoreLocation="LocalMachine" revocationMode="Online"/> </clientCertificate> </serviceCredentials> </behavior> </serviceBehaviors> </behaviors> <bindings> <wsHttpBinding> <binding name="CertificateWithTransportWSHttpBinding"> <security mode="Transport"> <transport clientCredentialType="Certificate" /> </security> </binding> </wsHttpBinding> </bindings> </system.serviceModel> </configuration> I've configured IIS as follows: https binding added using self signed certificate Under SSL settings, require SSL and accept client certificates is checked The self signed certificate has been added to the Local Computer Trusted Root CA. I can browse and execute the .asmx service definition, but the .svc gives me the error described above.

  Read the article

• Asus me302c create script crash

  - by wxfred

  State beforehand: So far, only Asus me302c would crash when it creates a script. This device can create renderscript context successfully 06-03 10:12:50.509: V/RenderScript_jni(3144): RS compat mode 06-03 10:12:50.509: V/RenderScript(3144): 0x610bbfc0 Launching thread(s), CPUs 4 06-03 10:12:50.549: D/libEGL(3144): loaded /vendor/lib/egl/libEGL_POWERVR_SGX544_115.so 06-03 10:12:50.559: D/libEGL(3144): loaded /vendor/lib/egl/libGLESv1_CM_POWERVR_SGX544_115.so 06-03 10:12:50.559: D/libEGL(3144): loaded /vendor/lib/egl/libGLESv2_POWERVR_SGX544_115.so 06-03 10:12:50.619: D/OpenGLRenderer(3144): Enabling debug mode 0 06-03 10:12:52.869: D/dalvikvm(3144): Rejecting registerization due to ushr-int/lit8 v4, v7, (#19) When create a script, it crashed. 06-03 09:55:09.859: D/basefilter(26682): ===createScript=== 06-03 09:55:09.869: E/RenderScript(26682): Unable to open shared library (/data/data/xxx.xxxxxxxxxxx.xxxxxxxxx.xxxxx.xxxx//lib/librs.basefilter.so): Cannot load library: soinfo_relocate(linker.cpp:975): cannot locate symbol "_Z3dotDv3_fS_" referenced by "librs.basefilter.so"... 06-03 09:55:09.869: E/RenderScript(26682): Unable to open system shared library (/system/lib/librs.basefilter.so): (null) 06-03 09:55:09.869: D/AndroidRuntime(26682): Shutting down VM 06-03 09:55:09.869: W/dalvikvm(26682): threadid=1: thread exiting with uncaught exception (group=0x418b9e10) 06-03 09:55:09.869: E/AndroidRuntime(26682): FATAL EXCEPTION: main 06-03 09:55:09.869: E/AndroidRuntime(26682): android.support.v8.renderscript.RSRuntimeException: Loading of ScriptC script failed. 06-03 09:55:09.869: E/AndroidRuntime(26682): at android.support.v8.renderscript.ScriptC.<init>(ScriptC.java:69) 06-03 09:55:09.869: E/AndroidRuntime(26682): at xxx.xxxxxxxxxxx.xxxxxxxxx.xxxxxxxxxx.xxxxxx.ScriptC_BaseFilter.<init>(ScriptC_BaseFilter.java:41) 06-03 09:55:09.869: E/AndroidRuntime(26682): at xxx.xxxxxxxxxxx.xxxxxxxxx.xxxxxxxxxx.xxxxxx.ScriptC_BaseFilter.<init>(ScriptC_BaseFilter.java:35) 06-03 09:55:09.869: E/AndroidRuntime(26682): at xxx.xxxxxxxxxxx.xxxxxxxxx.xxxxxxxxxx.xxxxxx.xxxxxx.TeethWhiteningRSFilter.onCreateScript(TeethWhiteningRSFilter.java:19) 06-03 09:55:09.869: E/AndroidRuntime(26682): at xxx.xxxxxxxxxxx.xxxxxxxxx.xxxxxxxxxx.xxxxxx.xxxxxx.TeethWhiteningRSFilter.onCreateScript(TeethWhiteningRSFilter.java:1) 06-03 09:55:09.869: E/AndroidRuntime(26682): at xxx.xxxxxxxxxxx.xxxxxxxxx.xxxxxxxxxx.BaseRSFilter.createScript(BaseRSFilter.java:39) 06-03 09:55:09.869: E/AndroidRuntime(26682): at xxx.xxxxxxxxxxx.xxxxxxxxx.xxxxxxxxxx.RSFilterEngine.addFilter(RSFilterEngine.java:76) 06-03 09:55:09.869: E/AndroidRuntime(26682): at xxx.xxxxxxxxxxx.xxxxxxxxx.xxxxx.xxxx.BeautyActivity.changeBeautyEffect(BeautyActivity.java:277) 06-03 09:55:09.869: E/AndroidRuntime(26682): at xxx.xxxxxxxxxxx.xxxxxxxxx.xxxxx.xxxx.BeautyActivity$2.onClick(BeautyActivity.java:100) 06-03 09:55:09.869: E/AndroidRuntime(26682): at com.android.internal.app.AlertController$ButtonHandler.handleMessage(AlertController.java:166) 06-03 09:55:09.869: E/AndroidRuntime(26682): at android.os.Handler.dispatchMessage(Handler.java:99) 06-03 09:55:09.869: E/AndroidRuntime(26682): at android.os.Looper.loop(Looper.java:152) 06-03 09:55:09.869: E/AndroidRuntime(26682): at android.app.ActivityThread.main(ActivityThread.java:5132) 06-03 09:55:09.869: E/AndroidRuntime(26682): at java.lang.reflect.Method.invokeNative(Native Method) 06-03 09:55:09.869: E/AndroidRuntime(26682): at java.lang.reflect.Method.invoke(Method.java:511) 06-03 09:55:09.869: E/AndroidRuntime(26682): at com.android.internal.os.ZygoteInit$MethodAndArgsCaller.run(ZygoteInit.java:793) 06-03 09:55:09.869: E/AndroidRuntime(26682): at com.android.internal.os.ZygoteInit.main(ZygoteInit.java:560) 06-03 09:55:09.869: E/AndroidRuntime(26682): at dalvik.system.NativeStart.main(Native Method) Now, I will post some related infomation. project.properties ... renderscript.target=9 renderscript.support.mode=true sdk.buildtools=19.0.3 device info Brand: Asus Model: ME302C OS: 4.2.2 CPU: Intel(R) Atom(TM) CPU Z2560 @1.60GHz GPU Renderer PowerVR SGX 544MP Finally, by the way, the same code runs well on Galaxy s2, s4, note 2.

  Read the article

• How to get updated automatically WPF TreeViewItems with values based on .Net class properties?

  - by ProgrammerManiac

  Good morning. I have a class with data derived from InotifyPropertyChange. The data come from a background thread, which searches for files with certain extension in certain locations. Public property of the class reacts to an event OnPropertyChange by updating data in a separate thread. Besides, there are described in XAML TreeView, based on HierarhicalDataTemplates. Each TextBlock inside templates supplied ItemsSource = "{Binding FoundFilePaths, Mode = OneWay, NotifyOnTargetUpdated = True}". enter code here <HierarchicalDataTemplate DataType = "{x:Type lightvedo:FilesInfoStore}" ItemsSource="{Binding FoundFilePaths, Mode=OneWay, NotifyOnTargetUpdated=True}"> <!--????? ??????????? ???? ??????--> <StackPanel x:Name ="TreeNodeStackPanel" Orientation="Horizontal"> <TextBlock Margin="5,5,5,5" TargetUpdated="TextBlockExtensions_TargetUpdated"> <TextBlock.Text> <MultiBinding StringFormat="Files with Extension {0}"> <Binding Path="FileExtension"/> </MultiBinding> </TextBlock.Text> </TextBlock> <Button x:Name="OpenFolderForThisFiles" Click="OnOpenFolderForThisFiles_Click" Margin="5, 3, 5, 3" Width="22" Background="Transparent" BorderBrush="Transparent" BorderThickness="0.5"> <Image Source="images\Folder.png" Height="16" Width="20" > </Image> </Button> </StackPanel> </HierarchicalDataTemplate> <HierarchicalDataTemplate DataType="{x:Type lightvedo:FilePathsStore}"> <TextBlock Text="{Binding FilePaths, Mode=OneWay, NotifyOnTargetUpdated=True}" TargetUpdated="OnTreeViewNodeChildren_Update" /> </HierarchicalDataTemplate> </TreeView.Resources> <TreeView.RenderTransform> <TransformGroup> <ScaleTransform/> <SkewTransform AngleX="-0.083"/> <RotateTransform/> <TranslateTransform X="-0.249"/> </TransformGroup> </TreeView.RenderTransform> <TreeView.BorderBrush> <LinearGradientBrush EndPoint="1,0.5" StartPoint="0,0.5"> <GradientStop Color="#FF74591F" Offset="0" /> <GradientStop Color="#FF9F7721" Offset="1" /> <GradientStop Color="#FFD9B972" Offset="0.49" /> </LinearGradientBrush> </TreeView.BorderBrush> </TreeView> Q: Why is the data from a class derived from INotifyPropertyChange does not affect the display of tree items. Do I understand: The interface will make INotifyPropertyChange be automatically redrawn TreeViewItems or do I need to manually carry out this operation? Currently TreeViewItems not updated and PropertyChamged always null. A feeling that no subscribers to the event OnPropertyChanged.

  Read the article

• Rogue PropertyChanged notifications from ViewModel

  - by user1886323

  The following simple program is causing me a Databinding headache. I'm new to this which is why I suspect it has a simple answer. Basically, I have two text boxes bound to the same property myString. I have not set up the ViewModel (simply a class with one property, myString) to provide any notifications to the View for when myString is changed, so even although both text boxes operate a two way binding there should be no way that the text boxes update when myString is changed, am I right? Except... In most circumstances this is true - I use the 'change value' button at the bottom of the window to change the value of myString to whatever the user types into the adjacent text box, and the two text boxes at the top, even although they are bound to myString, do not change. Fine. However, if I edit the text in TextBox1, thus changing the value of myString (although only when the text box loses focus due to the default UpdateSourceTrigger property, see reference), TextBox2 should NOT update as it shouldn't receive any updates that myString has changed. However, as soon as TextBox1 loses focus (say click inside TextBox2) TextBox2 is updated with the new value of myString. My best guess so far is that because the TextBoxes are bound to the same property, something to do with TextBox1 updating myString gives TextBox2 a notification that it has changed. Very confusing as I haven't used INotifyPropertyChanged or anything like that. To clarify, I am not asking how to fix this. I know I could just change the binding mode to a oneway option. I am wondering if anyone can come up with an explanation for this strange behaviour? ViewModel: namespace WpfApplication1 { class ViewModel { public ViewModel() { _myString = "initial message"; } private string _myString; public string myString { get { return _myString; } set { if (_myString != value) { _myString = value; } } } } } View: <Window x:Class="WpfApplication1.MainWindow" xmlns="http://schemas.microsoft.com/winfx/2006/xaml/presentation" xmlns:x="http://schemas.microsoft.com/winfx/2006/xaml" xmlns:local="clr-namespace:WpfApplication1" Title="MainWindow" Height="350" Width="525"> <Window.DataContext> <local:ViewModel /> </Window.DataContext> <Grid> <!-- The culprit text boxes --> <TextBox Height="23" HorizontalAlignment="Left" Margin="166,70,0,0" Name="textBox1" VerticalAlignment="Top" Width="120" Text="{Binding Path=myString, Mode=TwoWay}" /> <TextBox Height="23" HorizontalAlignment="Left" Margin="166,120,0,0" Name="textBox2" VerticalAlignment="Top" Width="120" Text="{Binding Path=myString, Mode=TwoWay}"/> <!--The buttons allowing manual change of myString--> <Button Name="changevaluebutton" Content="change value" Click="ButtonUpdateArtist_Click" Margin="12,245,416,43" Width="75" /> <Button Content="Show value" Height="23" HorizontalAlignment="Left" Margin="12,216,0,0" Name="showvaluebutton" VerticalAlignment="Top" Width="75" Click="showvaluebutton_Click" /> <Label Content="" Height="23" HorizontalAlignment="Left" Margin="116,216,0,0" Name="showvaluebox" VerticalAlignment="Top" Width="128" /> <TextBox Height="23" HorizontalAlignment="Left" Margin="116,245,0,0" Name="changevaluebox" VerticalAlignment="Top" Width="128" /> <!--simply some text--> <Label Content="TexBox1" Height="23" HorizontalAlignment="Left" Margin="99,70,0,0" Name="label1" VerticalAlignment="Top" Width="61" /> <Label Content="TexBox2" Height="23" HorizontalAlignment="Left" Margin="99,118,0,0" Name="label2" VerticalAlignment="Top" Width="61" /> </Grid> </Window> Code behind for view: namespace WpfApplication1 { /// <summary> /// Interaction logic for MainWindow.xaml /// </summary> public partial class MainWindow : Window { ViewModel viewModel; public MainWindow() { InitializeComponent(); viewModel = (ViewModel)this.DataContext; } private void showvaluebutton_Click(object sender, RoutedEventArgs e) { showvaluebox.Content = viewModel.myString; } private void ButtonUpdateArtist_Click(object sender, RoutedEventArgs e) { viewModel.myString = changevaluebox.Text; } } }

  Read the article

• Effective optimization strategies on modern C++ compilers

  - by user168715

  I'm working on scientific code that is very performance-critical. An initial version of the code has been written and tested, and now, with profiler in hand, it's time to start shaving cycles from the hot spots. It's well-known that some optimizations, e.g. loop unrolling, are handled these days much more effectively by the compiler than by a programmer meddling by hand. Which techniques are still worthwhile? Obviously, I'll run everything I try through a profiler, but if there's conventional wisdom as to what tends to work and what doesn't, it would save me significant time. I know that optimization is very compiler- and architecture- dependent. I'm using Intel's C++ compiler targeting the Core 2 Duo, but I'm also interested in what works well for gcc, or for "any modern compiler." Here are some concrete ideas I'm considering: Is there any benefit to replacing STL containers/algorithms with hand-rolled ones? In particular, my program includes a very large priority queue (currently a std::priority_queue) whose manipulation is taking a lot of total time. Is this something worth looking into, or is the STL implementation already likely the fastest possible? Along similar lines, for std::vectors whose needed sizes are unknown but have a reasonably small upper bound, is it profitable to replace them with statically-allocated arrays? I've found that dynamic memory allocation is often a severe bottleneck, and that eliminating it can lead to significant speedups. As a consequence I'm interesting in the performance tradeoffs of returning large temporary data structures by value vs. returning by pointer vs. passing the result in by reference. Is there a way to reliably determine whether or not the compiler will use RVO for a given method (assuming the caller doesn't need to modify the result, of course)? How cache-aware do compilers tend to be? For example, is it worth looking into reordering nested loops? Given the scientific nature of the program, floating-point numbers are used everywhere. A significant bottleneck in my code used to be conversions from floating point to integers: the compiler would emit code to save the current rounding mode, change it, perform the conversion, then restore the old rounding mode --- even though nothing in the program ever changed the rounding mode! Disabling this behavior significantly sped up my code. Are there any similar floating-point-related gotchas I should be aware of? One consequence of C++ being compiled and linked separately is that the compiler is unable to do what would seem to be very simple optimizations, such as move method calls like strlen() out of the termination conditions of loop. Are there any optimization like this one that I should look out for because they can't be done by the compiler and must be done by hand? On the flip side, are there any techniques I should avoid because they are likely to interfere with the compiler's ability to automatically optimize code? Lastly, to nip certain kinds of answers in the bud: I understand that optimization has a cost in terms of complexity, reliability, and maintainability. For this particular application, increased performance is worth these costs. I understand that the best optimizations are often to improve the high-level algorithms, and this has already been done.

  Read the article

• Access/update Telerik RadGrid item values in code-behind before ODS event handler

  - by Brent

  Hi there, I need to update some of the values of the item being edited in my code-behind based on some values in a custom Edit Form on our Rad Grid. Can I access the item (and update some values) from one of the Grid's event handlers? Currently I'm storing the values in temporary variables and then injecting the new values in the ObjectDataSource's Inserting/Updating event handlers, but it would be much nicer if I could do it all in one spot. (I can't do it all in the ObjectDataSource event handlers as I can't access the controls inside my Grid's Edit Form.) I've been playing with the ExtractValues and UpdateValues methods of the GridEditableItem object, but I'm not having any luck. Any tips would be greatly appreciated :)

  Read the article

• Programmatically examine DLL contents

  - by Peter Hansen

  Is it possible programmatically to discover the exported names (globals, entry points, whatever) in a Windows DLL file without implementing a parser for the binary executable file format itself? I know there are tools to do this (though no open source ones I've found), but I'm curious whether there is a Windows API to accomplish the same thing or whether such tools operate merely by examining the binary file directly. I suspect there is an API for .NET libraries: if that's the case then is there a similar one for native DLLs? Edit: http://stackoverflow.com/questions/1128150 is basically an exact duplicate. The answer there is roughly "there is no API, but you can hack it using LoadLibraryEx() and navigating a few resulting data structures". Edit: I was able to use the accepted answer at http://stackoverflow.com/questions/1128150 to create a quick DLL dumper with Python and ctypes that works.

  Read the article

• page loads twice in Google chrome

  - by Cristian Boariu

  Hi guys, Does anyone have any problems with Page_Load being executed twice in Google Chrome? It's a short question, i do not know what else to explain... I have a simple asp.net page and in Firefox and IE all it's working fine. But in Chrome the Page_Load is fired twice... Anyone has any ideas why? Later EDIT: - what is strange is that i have 4 repeaters... binded with random values. The random methods are twice fired (because of page loaded twice) but the repeaters takes the INITIALLY values...so, the 2nd post back is somehow raised after the rendering step. 3rd edit: It happens ONLY at the refresh!

  Read the article

• javascript flowchart library for workflow visualization

  - by jonny

  I need to generate flowchart from business process specification (tasks, their input, output points, roles applicable for each task... ) stored in a database. What I need is javacript (preferably, open-sourced) library which can generate a shiny flowchart with swimlines. Ideally I should be able to edit workflow items connections and send changes back to database. Any recommendations? UPDATE By flowchart I mean something like this: UPDATE Found open-source project which that allows create/edit basic flowcharts here Tt seems abanddoned since 2007.

  Read the article

• Installing SharePoint 2010 and PowerPivot for SharePoint on Windows 7

  - by smisner

  Many people like me want (or need) to do their business intelligence development work on a laptop. As someone who frequently speaks at various events or teaches classes on all subjects related to the Microsoft business intelligence stack, I need a way to run multiple server products on my laptop with reasonable performance. Once upon a time, that requirement meant only that I had to load the current version of SQL Server and the client tools of choice. In today's post, I'll review my latest experience with trying to make the newly released Microsoft BI products work with a Windows 7 operating system.The entrance of Microsoft Office SharePoint Server 2007 into the BI stack complicated matters and I started using Virtual Server to establish a "suitable" environment. As part of the team that delivered a lot of education as part of the Yukon pre-launch activities (that would be SQL Server 2005 for the uninitiated), I was working with four - yes, four - virtual servers. That was a pretty brutal workload for a 2GB laptop, which worked if I was very, very careful. It could also be a finicky and unreliable configuration as I learned to my dismay at one TechEd session several years ago when I had to reboot a very carefully cached set of servers just minutes before my session started. Although it worked, it came back to life very, very slowly much to the displeasure of the audience. They couldn't possibly have been less pleased than me.At that moment, I resolved to get the beefiest environment I could afford and consolidate to a single virtual server. Enter the 4GB 64-bit laptop to preserve my sanity and my livelihood. Likewise, for SQL Server 2008, I managed to keep everything within a single virtual server and I could function reasonably well with this approach.Now we have SQL Server 2008 R2 plus Office SharePoint Server 2010. That means a 64-bit operating system. Period. That means no more Virtual Server. That means I must use Hyper-V or another alternative. I've heard alternatives exist, but my few dabbles in this area did not yield positive results. It might have been just me having issues rather than any failure of those technologies to adequately support the requirements.My first run at working with the new BI stack configuration was to set up a 64-bit 4GB laptop with a dual-boot to run Windows Server 2008 R2 with Hyper-V. However, I was generally not happy with running Windows Server 2008 R2 on my laptop. For one, I couldn't put it into sleep mode, which is helpful if I want to prepare for a presentation beforehand and then walk to the podium without the need to hold my laptop in its open state along the way (my strategy at the TechEd session long, long ago). Secondly, it was finicky with projectors. I had issues from time to time and while I always eventually got it to work, I didn't appreciate those nerve-wracking moments wondering whether this would be the time that it wouldn't work.Somewhere along the way, I learned that it was possible to load SharePoint 2010 in a Windows 7 which piqued my interest. I had just acquired a new laptop running Windows 7 64-bit, and thought surely running the BI stack natively on my laptop must be better than running Hyper-V. (I have not tried booting to Hyper-V VHD yet, but that's on my list of things to try so the jury of one is still out on this approach.) Recently, I had to build up a server with the RTM versions of SQL Server 2008 R2 and Sharepoint Server 2010 and decided to follow suit on my Windows 7 Ultimate 64-bit laptop. The process is slightly different, but I'm happy to report that it IS possible, although I had some fits and starts along the way.DISCLAIMER: These products are NOT intended to be run in production mode on the Windows 7 operating system. The configuration described in this post is strictly for development or learning purposes and not supported by Microsoft. If you have trouble, you will NOT get help from them. I might be able to help, but I provide no guarantees of my ability or availablity to help. I won't provide the step-by-step instructions in this post as there are other resources that provide these details, but I will provide an overview of my approach, point you to the relevant resources, describe some of the problems I encountered, and explain how I addressed those problems to achieve my desired goal.Because my goal was not simply to set up SharePoint Server 2010 on my laptop, but specifically PowerPivot for SharePoint, I started out by referring to the installation instructions at the PowerPiovt-Info site, but mainly to confirm that I was performing steps in the proper sequence. I didn't perform the steps in Part 1 because those steps are applicable only to a server operating system which I am not running on my laptop. Then, the instructions in Part 2, won't work exactly as written for the same reason. Instead, I followed the instructions on MSDN, Setting Up the Development Environment for SharePoint 2010 on Windows Vista, Windows 7, and Windows Server 2008. In general, I found the following differences in installation steps from the steps at PowerPivot-Info:You must copy the SharePoint installation media to the local drive so that you can edit the config.xml to allow installation on a Windows client.You also have to manually install the prerequisites. The instructions provides links to each item that you must manually install and provides a command-line instruction to execute which enables required Windows features.I will digress for a moment to save you some grief in the sequence of steps to perform. I discovered later that a missing step in the MSDN instructions is to install the November CTP Reporting Services add-in for SharePoint. When I went to test my SharePoint site (I believe I tested after I had a successful PowerPivot installation), I ran into the following error: Could not load file or assembly 'RSSharePointSoapProxy, Version=10.0.0.0, Culture=neutral, PublicKeyToken=89845dcd8080cc91' or one of its dependencies. The system cannot find the file specified. I was rather surprised that Reporting Services was required. Then I found an article by Alan le Marquand, Working Together: SQL Server 2008 R2 Reporting Services Integration in SharePoint 2010,that instructed readers to install the November add-in. My first reaction was, "Really?!?" But I confirmed it in another TechNet article on hardware and software requirements for SharePoint Server 2010. It doesn't refer explicitly to the November CTP but following the link took me there. (Interestingly, I retested today and there's no longer any reference to the November CTP. Here's the link to download the latest and greatest Reporting Services Add-in for SharePoint Technologies 2010.) You don't need to download the add-in anymore if you're doing a regular server-based installation of SharePoint because it installs as part of the prerequisites automatically.When it was time to start the installation of SharePoint, I deviated from the MSDN instructions and from the PowerPivot-Info instructions:On the Choose the installation you want page of the installation wizard, I chose Server Farm.On the Server Type page, I chose Complete.At the end of the installation, I did not run the configuration wizard.Returning to the PowerPivot-Info instructions, I tried to follow the instructions in Part 3 which describe installing SQL Server 2008 R2 with the PowerPivot option. These instructions tell you to choose the New Server option on the Setup Role page where you add PowerPivot for SharePoint. However, I ran into problems with this approach and got installation errors at the end.It wasn't until much later as I was investigating an error that I encountered Dave Wickert's post that installing PowerPivot for SharePoint on Windows 7 is unsupported. Uh oh. But he did want to hear about it if anyone succeeded, so I decided to take the plunge. Perseverance paid off, and I can happily inform Dave that it does work so far. I haven't tested absolutely everything with PowerPivot for SharePoint but have successfully deployed a workbook and viewed the PowerPivot Management Dashboard. I have not yet tested the data refresh feature, but I have installed. Continue reading to see how I accomplished my objective.I unintalled SQL Server 2008 R2 and started again. I had different problems which I don't recollect now. However, I uninstalled again and approached installation from a different angle and my next attempt succeeded. The downside of this approach is that you must do all of the things yourself that are done automatically when you install PowerPivot as a new server. Here are the steps that I followed:Install SQL Server 2008 R2 to get a database engine instance installed.Run the SharePoint configuration wizard to set up the SharePoint databases.In Central Administration, create a Web application using classic mode authentication as per a TechNet article on PowerPivot Authentication and Authorization.Then I followed the steps I found at How to: Install PowerPivot for SharePoint on an Existing SharePoint Server. Especially important to note - you must launch setup by using Run as administrator. I did not have to manually deploy the PowerPivot solution as the instructions specify, but it's good to know about this step because it tells you where to look in Central Administration to confirm a successful deployment.I did spot some incorrect steps in the instructions (at the time of this writing) in How To: Configure Stored Credentials for PowerPivot Data Refresh. Specifically, in the section entitled Step 1: Create a target application and set the credentials, both steps 10 and 12 are incorrect. They tell you to provide an actual Windows user name and password on the page where you are simply defining the prompts for your application in the Secure Store Service. To add the Windows user name and password that you want to associate with the application - after you have successfully created the target application - you select the target application and then click Set credentials in the ribbon.Lastly, I followed the instructions at How to: Install Office Data Connectivity Components on a PowerPivot server. However, I have yet to test this in my current environment.I did have several stops and starts throughout this process and edited those out to spare you from reading non-essential information. I believe the explanation I have provided here accurately reflect the steps I followed to produce a working configuration. If you follow these steps and get a different result, please let me know so that together we can work through the issue and correct these instructions. I'm sure there are many other folks in the Microsoft BI community that will appreciate the ability to set up the BI stack in a Windows 7 environment for development or learning purposes. Share this post: email it! | bookmark it! | digg it! | reddit! | kick it! | live it!

  Read the article

• Create a Bootable Ubuntu 9.10 USB Flash Drive

  - by Trevor Bekolay

  The Ubuntu Live CD isn’t just useful for trying out Ubuntu before you install it, you can also use it to maintain and repair your Windows PC. Even if you have no intention of installing Linux, every Windows user should have a bootable Ubuntu USB drive on hand in case something goes wrong in Windows. Creating a bootable USB flash drive is surprisingly easy with a small self-contained application called UNetbootin. It will even download Ubuntu for you! Note: Ubuntu will take up approximately 700 MB on your flash drive, so choose a flash drive with at least 1 GB of free space, formatted as FAT32. This process should not remove any existing files on the flash drive, but to be safe you should backup the files on your flash drive. Put Ubuntu on your flash drive UNetbootin doesn’t require installation; just download the application and run it. Select Ubuntu from the Distribution drop-down box, then 9.10_Live from the Version drop-down box. If you have a 64-bit machine, then select 9.10_Live_x64 for the Version. At the bottom of the screen, select the drive letter that corresponds to the USB drive that you want to put Ubuntu on. If you select USB Drive in the Type drop-down box, the only drive letters available will be USB flash drives. Click OK and UNetbootin will start doing its thing. First it will download the Ubuntu Live CD. Then, it will copy the files from the Ubuntu Live CD to your flash drive. The amount of time it takes will vary depending on your Internet speed, an when it’s done, click on Exit. You’re not planning on installing Ubuntu right now, so there’s no need to reboot. If you look at the USB drive now, you should see a bunch of new files and folders. If you had files on the drive before, they should still be present. You’re now ready to boot your computer into Ubuntu 9.10! How to boot into Ubuntu When the time comes that you have to boot into Ubuntu, or if you just want to test and make sure that your flash drive works properly, you will have to set your computer to boot off of the flash drive. The steps to do this will vary depending on your BIOS – which varies depending on your motherboard. To get detailed instructions on changing how your computer boots, search for your motherboard’s manual (or your laptop’s manual for a laptop). For general instructions, which will suffice for 99% of you, read on. Find the important keyboard keys When your computer boots up, a bunch of words and numbers flash across the screen, usually to be ignored. This time, you need to scan the boot-up screen for a few key words with some associated keys: Boot menu and Setup. Typically, these will show up at the bottom of the screen. If your BIOS has a Boot Menu, then read on. Otherwise, skip to the Hard: Using Setup section. Easy: Using the Boot Menu If your BIOS offers a Boot Menu, then during the boot-up process, press the button associated with the Boot Menu. In our case, this is ESC. Our example Boot Menu doesn’t have the ability to boot from USB, but your Boot Menu should have some options, such as USB-CDROM, USB-HDD, USB-FLOPPY, and others. Try the options that start with USB until you find one that works. Don’t worry if it doesn’t work – you can just restart and try again. Using the Boot Menu does not change the normal boot order on your system, so the next time you start up your computer it will boot from the hard drive as normal. Hard: Using Setup If your BIOS doesn’t offer a Boot Menu, then you will have to change the boot order in Setup. Note: There are some options in BIOS Setup that can affect the stability of your machine. Take care to only change the boot order options. Press the button associated with Setup. In our case, this is F2. If your BIOS Setup has a Boot tab, then switch to it and change the order such that one of the USB options occurs first. There may be several USB options, such as USB-CDROM, USB-HDD, USB-FLOPPY, and others; try them out to see which one works for you. If your BIOS does not have a boot tab, boot order is commonly found in Advanced CMOS Options. Note that this changes the boot order permanently until you change it back. If you plan on only plugging in a bootable flash drive when you want to boot from it, then you could leave the boot order as it is, but you may find it easier to switch the order back to the previous order when you reboot from Ubuntu. Booting into Ubuntu If you set the right boot option, then you should be greeted with the UNetbootin screen. Press enter to start Ubuntu with the default options, or wait 10 seconds for this to happen automatically. Ubuntu will start loading. It should go straight to the desktop with no need for a username or password. And that’s it! From this live desktop session, you can try out Ubuntu, and even install software that is not included in the live CD. Installed software will only last for the duration of your session – the next time you start up the live CD it will be back to its original state. Download UNetbootin from sourceforge.net Similar Articles Productive Geek Tips Create a Bootable Ubuntu USB Flash Drive the Easy WayReset Your Ubuntu Password Easily from the Live CDHow-To Geek on Lifehacker: Control Your Computer with Shortcuts & Speed Up Vista SetupHow To Setup a USB Flash Drive to Install Windows 7Speed up Your Windows Vista Computer with ReadyBoost TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 PCmover Professional New Stinger from McAfee Helps Remove ‘FakeAlert’ Threats Google Apps Marketplace: Tools & Services For Google Apps Users Get News Quick and Precise With Newser Scan for Viruses in Ubuntu using ClamAV Replace Your Windows Task Manager With System Explorer Create Talking Photos using Fotobabble

  Read the article

• Conversation as User Assistance

  - by ultan o'broin

  Applications User Experience members (Erika Web, Laurie Pattison, and I) attended the User Assistance Europe Conference in Stockholm, Sweden. We were impressed with the thought leadership and practical application of ideas in Anne Gentle's keynote address "Social Web Strategies for Documentation". After the conference, we spoke with Anne to explore the ideas further. Anne Gentle (left) with Applications User Experience Senior Director Laurie Pattison In Anne's book called Conversation and Community: The Social Web for Documentation, she explains how user assistance is undergoing a seismic shift. The direction is away from the old print manuals and online help concept towards a web-based, user community-driven solution using social media tools. User experience professionals now have a vast range of such tools to start and nurture this "conversation": blogs, wikis, forums, social networking sites, microblogging systems, image and video sharing sites, virtual worlds, podcasts, instant messaging, mashups, and so on. That user communities are a rich source of user assistance is not a surprise, but the extent of available assistance is. For example, we know from the Consortium for Service Innovation that there has been an 'explosion' of user-generated content on the web. User-initiated community conversations provide as much as 30 times the number of official help desk solutions for consortium members! The growing reliance on user community solutions is clearly a user experience issue. Anne says that user assistance as conversation "means getting closer to users and helping them perform well. User-centered design has been touted as one of the most important ideas developed in the last 20 years of workplace writing. Now writers can take the idea of user-centered design a step further by starting conversations with users and enabling user assistance in interactions." Some of Anne's favorite examples of this paradigm shift from the world of traditional documentation to community conversation include: Writer Bob Bringhurst's blog about Adobe InDesign and InCopy products and Adobe's community help The Microsoft Development Network Community Center ·The former Sun (now Oracle) OpenDS wiki, NetBeans Ruby and other community approaches to engage diverse audiences using screencasts, wikis, and blogs. Cisco's customer support wiki, EMC's community, as well as Symantec and Intuit's approaches The efforts of Ubuntu, Mozilla, and the FLOSS community generally Adobe Writer Bob Bringhurst's Blog Oracle is not without a user community conversation too. Besides the community discussions and blogs around documentation offerings, we have the My Oracle Support Community forums, Oracle Technology Network (OTN) communities, wiki, blogs, and so on. We have the great work done by our user groups and customer councils. Employees like David Haimes reach out, and enthusiastic non-employee gurus like Chet Justice (OracleNerd), Floyd Teter and Eddie Awad provide great "how-to" information too. But what does this paradigm shift mean for existing technical writers as users turn away from the traditional printable PDF manual deliverables? We asked Anne after the conference. The writer role becomes one of conversation initiator or enabler. The role evolves, along with the process, as the users define their concept of user assistance and terms of engagement with the product instead of having it pre-determined. It is largely a case now of "inventing the job while you're doing it, instead of being hired for it" Anne said. There is less emphasis on formal titles. Anne mentions that her own title "Content Stacker" at OpenStack; others use titles such as "Content Curator" or "Community Lead". However, the role remains one essentially about communications, "but of a new type--interacting with users, moderating, curating content, instead of sitting down to write a manual from start to finish." Clearly then, this role is open to more than professional technical writers. Product managers who write blogs, developers who moderate forums, support professionals who update wikis, rock star programmers with a penchant for YouTube are ideal. Anyone with the product knowledge, empathy for the user, and flair for relationships on the social web can join in. Some even perform these roles already but do not realize it. Anne feels the technical communicator space will move from hiring new community conversation professionals (who are already active in the space through blogging, tweets, wikis, and so on) to retraining some existing writers over time. Our own research reveals that the established proponents of community user assistance even set employee performance objectives for internal content curators about the amount of community content delivered by people outside the organization! To take advantage of the conversations on the web as user assistance, enterprises must first establish where on the spectrum their community lies. "What is the line between community willingness to contribute and the enterprise objectives?" Anne asked. "The relationship with users must be managed and also measured." Anne believes that the process can start with a "just do it" approach. Begin by reaching out to existing user groups, individual bloggers and tweeters, forum posters, early adopter program participants, conference attendees, customer advisory board members, and so on. Use analytical tools to measure the level of conversation about your products and services to show a return on investment (ROI), winning management support. Anne emphasized that success with the community model is dependent on lowering the technical and motivational barriers so that users can readily contribute to the conversation. Simple tools must be provided, and guidelines, if any, must be straightforward but not mandatory. The conversational approach is one where traditional style and branding guides do not necessarily apply. Tools and infrastructure help users to create content easily, to search and find the information online, read it, rate it, translate it, and participate further in the content's evolution. Recognizing contributors by using ratings on forums, giving out Twitter kudos, conference invitations, visits to headquarters, free products, preview releases, and so on, also encourages the adoption of the conversation model. The move to conversation as user assistance is not free, but there is a business ROI. The conversational model means that customer service is enhanced, as user experience moves from a functional to a valued, emotional level. Studies show a positive correlation between loyalty and financial performance (Consortium for Service Innovation, 2010), and as customer experience and loyalty become key differentiators, user experience professionals cannot explore the model's possibilities. The digital universe (measured at 1.2 million petabytes in 2010) is doubling every 12 to 18 months, and 70 percent of that universe consists of user-generated content (IDC, 2010). Conversation as user assistance cannot be ignored but must be embraced. It is a time to manage for abundance, not scarcity. Besides, the conversation approach certainly sounds more interesting, rewarding, and fun than the traditional model! I would like to thank Anne for her time and thoughts, and recommend that all user assistance professionals read her book. You can follow Anne on Twitter at: http://www.twitter.com/annegentle. Oracle's Acrolinx IQ deployment was used to author this article.

  Read the article

< Previous Page | 263 264 265 266 267 268 269 270 271 272 273 274  | Next Page >