Search Results

Search found 10211 results on 409 pages for 'adf controller'.

Page 268/409 | < Previous Page | 264 265 266 267 268 269 270 271 272 273 274 275 | Next Page >

Server 2012 R2 DNS Conditional forwarding not working reliably, possible caching issue?

- by Matt

I have a bit of a home lab setup with a domain controller that is acting as the DNS server for my network. For everything, it's working fine and forwards external DNS requests to my ISP. The household recently wanted to get Netflix going and it seemed a DNS option was better than a VPN to get around the region locking, so I signed up for unblock-us.com Since I have a Windows DNS server I thought I'd be clever and make use of conditional forwarders and added the Netflix domain to the list. Initially this worked well and all devices on the network could now access Netflix, however after about an hour going to the Netflix site would result in a page cannot be found. Doing an nslookup of Netflix.com from my PC resulted in it not returning any IP addresses. As a test, I deleted the Netflix domain from the DNS servers cache and things started working again - devices could get to the site again however the same thing happens again after around half an hour to an hour. Have I missed something here that's causing it to stop working?

Read the article
Can I use dmraid instead of md (mdadm) to make software RAID-1 and RAID-1+0 volumes?

- by Don MacAskill

On a related question about SSDs and TRIM (see: Possible to get SSD TRIM (discard) working on ext4 + LVM + software RAID in Linux? ), it turns out that dmraid may now (or shortly) support TRIM on RAID-1. Typically, we've used md (via mdadm) to create our RAID-1 volumes, then used LVM to create volume groups, then formatted with the file system of our choice (ext4 lately). We've been doing this for years, and Google & ServerFault searches seem to confirm this is the most common way of doing software RAID with volume management. Google searches seem to suggest that dmraid is use for so-called 'fakeRAID' configurations where there's some level of hardware 'help' in the form of RAID BIOS in the controller, which we don't have (and don't want to use - we'd like a fully software solution). Since we'd like to use TRIM on our SSDs, and since md doesn't seem to (yet?) support TRIM, I'm wondering if it's possible to use dmraid instead of md to create RAID-1 (and RAID-1+0) volumes in software, with no hardware support (ie, just plugged into a dumb SATA/SAS bus)?

Read the article
Create and use intermediate certificate authority on Windows Server 2012?

- by Sid

Background: Server OS is Windows Server 2012. GUI is installed as we come upto speed with powershell. Setup is staging, not production (yet). We have our (internal, domain limited) Root CA installed. I would like to take the Root CA offline to secure storage but before that I'd like to setup an intermediate CA which can take over actual live, online (int-RA-net) functionality Can someone guide me covering: creating the intermediate CA certificate request installing the intermediate CA certificate on domain controller (certification authority role already installed with Root CA online right now) use the intermediate CA to generate a certificate (any use certificate, just for demonstration purposes) Obviously this certification chain would be invalid on computers outside our domain (self trusted root - our root certificate is NOT from common 3rd parties). This last point is NOT a problem.

Read the article
ZFS and SAN -- best practices?

- by chris

Most discussions of ZFS suggest that the hardware RAID be turned off and that ZFS should directly talk to the disks and manage the RAID on the host (instead of the RAID controller). This makes sense on a computer with 2-16 or even more local disks, but what about in an environment with a large SAN? For example, the enterprise I work for has what I would consider to be a modest sized SAN with 2 full racks of disks, which is something like 400 spindles. I've seen SAN shelves that are way more dense than ours, and SAN deployments way larger than ours. Do people expose 100 disks directly to big ZFS servers? 300 disks? 3000 disks? Do the SAN management tools facilitate automated management of this sort of thing?

Read the article
Local User & Local Admin User Server 2008

- by Ammo

Hi I had a test recently and one of the questions was to create a file and local user and give the local user write permission to that file. I created the local user successfully however when I went to add permission to the file it would not find the local user when name was entered correctly, and idea what could have prevented this. Secondly I was asked to create a local admin account and give full permissions to the file, to my knowledge server 2008 has a built in admin account, and neither was the server a domain controller. Could you tell me what you would do in this situation? Many Thanks!

Read the article
Authorization error when testing FTP to UNC

- by user64204

We have a Windows Server 2008 R2 with Active Directory (hereafter called DC) running as a domain controller on which we have IIS and an FTP site installed. We have a second Server 2008 (hereafter called SHARE) which is joined to that domain and has a disk shared as a network share (\\share\Office). That network share is used as the ftp's physical path on DC. We've tested the FTP from the IIS FTP configuration panel, by clicking on Basic Settings... then Test Settings.... When setting Administrator as a username with the Connect as... option, everything is fine: When no user is provided we can the below error: Q1: Could someone explain in more understandable terms what is written in the Details text area?

Read the article
AD, Windows-NT Authentication queries

- by rockbala

Need Help on the following questions. When a users login (on a computer in the network) is validated against AD what is/are the authentication method used? When a users login is validated in Windows NT environment (not AD) what is/are the authentication method used? If all user's account is on AD, is it possible to change the authentication mechanism only (or protocols) from AD to NT and vice versa (if possible)? If part/whole of question 3 is valid, where should one look to change these authentication methods ? What is the difference between AD and Windows-NT authentication ? Windows server 2008 Domain controller used. Regards, Balaji

Read the article
Ubuntu 10.04 recognizing USB 2.0 external HD as USB 1.1

- by btucker

When I connect the USB 2.0 drive I see this: usb 1-4.3: new full speed USB device using ohci_hcd and address 5 so I know it's getting seen as USB 1.1. usb-devices shows that it really is USB 2.0 and connected to a USB 2.0 hub: T: Bus=01 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#= 2 Spd=12 MxCh= 4 D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=05e3 ProdID=0608 Rev=77.61 S: Product=USB2.0 Hub C: #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=100mA I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub T: Bus=01 Lev=02 Prnt=02 Port=01 Cnt=01 Dev#= 4 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=13fd ProdID=1340 Rev=02.10 S: Manufacturer=Generic S: Product=External C: #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr=2mA I: If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage It seems the problem is that root hub is: T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh=10 D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1d6b ProdID=0001 Rev=02.06 S: Manufacturer=Linux 2.6.32-25-server ohci_hcd S: Product=OHCI Host Controller S: SerialNumber=0000:00:02.0 C: #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=0mA I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub And there's no mention of ehci_hcd. lsusb -t gives me: /: Bus 01.Port 1: Dev 1, Class=root_hub, Driver=ohci_hcd/10p, 12M |__ Port 4: Dev 2, If 0, Class=hub, Driver=hub/4p, 12M |__ Port 2: Dev 4, If 0, Class=stor., Driver=usb-storage, 12M |__ Port 3: Dev 5, If 0, Class=stor., Driver=usb-storage, 12M |__ Port 6: Dev 3, If 0, Class=stor., Driver=usb-storage, 12M It seems like I'm missing something which would allow the OS to see USB 2.0 devices. Can anyone point me in the right direction? EDIT Full lsusb -v output: Bus 001 Device 005: ID 13fd:1340 Initio Corporation Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 idVendor 0x13fd Initio Corporation idProduct 0x1340 bcdDevice 2.10 iManufacturer 1 Generic iProduct 2 External iSerial 3 57442D574341595930323337 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 32 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xc0 Self Powered MaxPower 2mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 2 bInterfaceClass 8 Mass Storage bInterfaceSubClass 6 SCSI bInterfaceProtocol 80 Bulk (Zip) iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x02 EP 2 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 0 Device Qualifier (for other device speed): bLength 10 bDescriptorType 6 bcdUSB 2.00 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 bNumConfigurations 1 Device Status: 0x0001 Self Powered Bus 001 Device 002: ID 05e3:0608 Genesys Logic, Inc. USB-2.0 4-Port HUB Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 9 Hub bDeviceSubClass 0 Unused bDeviceProtocol 0 Full speed (or root) hub bMaxPacketSize0 64 idVendor 0x05e3 Genesys Logic, Inc. idProduct 0x0608 USB-2.0 4-Port HUB bcdDevice 77.61 iManufacturer 0 iProduct 1 USB2.0 Hub iSerial 0 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 25 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xe0 Self Powered Remote Wakeup MaxPower 100mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 9 Hub bInterfaceSubClass 0 Unused bInterfaceProtocol 0 Full speed (or root) hub iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0001 1x 1 bytes bInterval 255 Hub Descriptor: bLength 9 bDescriptorType 41 nNbrPorts 4 wHubCharacteristic 0x00e0 Ganged power switching Ganged overcurrent protection Port indicators bPwrOn2PwrGood 50 * 2 milli seconds bHubContrCurrent 100 milli Ampere DeviceRemovable 0x00 PortPwrCtrlMask 0xff Hub Port Status: Port 1: 0000.0100 power Port 2: 0000.0103 power enable connect Port 3: 0000.0103 power enable connect Port 4: 0000.0100 power Device Qualifier (for other device speed): bLength 10 bDescriptorType 6 bcdUSB 2.00 bDeviceClass 9 Hub bDeviceSubClass 0 Unused bDeviceProtocol 1 Single TT bMaxPacketSize0 64 bNumConfigurations 1 Device Status: 0x0001 Self Powered Bus 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 1.10 bDeviceClass 9 Hub bDeviceSubClass 0 Unused bDeviceProtocol 0 Full speed (or root) hub bMaxPacketSize0 64 idVendor 0x1d6b Linux Foundation idProduct 0x0001 1.1 root hub bcdDevice 2.06 iManufacturer 3 Linux 2.6.32-25-server ohci_hcd iProduct 2 OHCI Host Controller iSerial 1 0000:00:02.0 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 25 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xe0 Self Powered Remote Wakeup MaxPower 0mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 9 Hub bInterfaceSubClass 0 Unused bInterfaceProtocol 0 Full speed (or root) hub iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0002 1x 2 bytes bInterval 255 Hub Descriptor: bLength 11 bDescriptorType 41 nNbrPorts 10 wHubCharacteristic 0x0002 No power switching (usb 1.0) Ganged overcurrent protection bPwrOn2PwrGood 1 * 2 milli seconds bHubContrCurrent 0 milli Ampere DeviceRemovable 0x00 0x00 PortPwrCtrlMask 0xff 0xff Hub Port Status: Port 1: 0000.0100 power Port 2: 0000.0100 power Port 3: 0000.0100 power Port 4: 0000.0103 power enable connect Port 5: 0000.0100 power Port 6: 0000.0103 power enable connect Port 7: 0000.0100 power Port 8: 0000.0100 power Port 9: 0000.0100 power Port 10: 0000.0100 power Device Status: 0x0003 Self Powered Remote Wakeup Enabled

Read the article
iSCSI RAID1 on two servers, fail scenario

- by Franz Kafka

Hallo, a simple question: Image I have two servers, each server has two disks in RAID1. Now I merge the two arrays with iSCSI to one RAID1 disk. Two questions: Can I do the merging of the 4 disks in one go? I can't image how. First I will have to install the os, and then the raid controller is already set up to RAID1. If a whole server fails the other server would continue working without any problems? Does iSCSI notice that the other server is missing and treet this as if the two disks were broken? When the server comes back online the data is resynced, as if I installed new disks into a array? Can I image that this way? Thanks alot.

Read the article
CentOS - Add additional hard drive raid arrays on Dell Perc 5/i card

- by Quanano

We have a Dell Poweredge 2900 system with Dell Perc 5/i card and 4 SAS hard drives attached, with NTFS partitions on them. We installed CentOS on one raid array on this controller with a different controller and it is working fine. We are now trying to access the drives shown above and they are not being shown in /dev as sdb, etc. sda is the drive that we installed centos on and it has sda1, sda2, sda3, etc. The CDROM has been picked up as well. If I scan for scsi devices then the perc and adaptec controllers are both found. sg0 is the CDROM and sg2 is the centos installed, however I think sg1 is the other drive but I cannot see anyway to mount the partitions, as only the drive is listed in /dev. Thanks. EXTRA INFO fdisk -l: Disk /dev/sda: 72.7 GB, 72746008576 bytes 255 heads, 63 sectors/track, 8844 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x11e3119f Device Boot Start End Blocks Id System /dev/sda1 * 1 64 512000 83 Linux Partition 1 does not end on cylinder boundary. /dev/sda2 64 8845 70528000 8e Linux LVM Disk /dev/mapper/vg_lal2server-lv_root: 34.4 GB, 34431041536 bytes 255 heads, 63 sectors/track, 4186 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/mapper/vg_lal2server-lv_root doesn't contain a valid partition table Disk /dev/mapper/vg_lal2server-lv_swap: 21.1 GB, 21139292160 bytes 255 heads, 63 sectors/track, 2570 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/mapper/vg_lal2server-lv_swap doesn't contain a valid partition table Disk /dev/mapper/vg_lal2server-lv_home: 16.6 GB, 16647192576 bytes 255 heads, 63 sectors/track, 2023 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/mapper/vg_lal2server-lv_home doesn't contain a valid partition table These are all from the install hdd not the additional hard drives modprobe a320raid FATAL: Module a320raid not found. lsscsi -v: [0:0:0:0] cd/dvd TSSTcorp CDRWDVD TS-H492C DE02 /dev/sr0 dir: /sys/bus/scsi/devices/0:0:0:0 [/sys/devices/pci0000:00/0000:00:1f.1/host0/target0:0:0/0:0:0:0] [4:0:10:0] enclosu DP BACKPLANE 1.05 - dir: /sys/bus/scsi/devices/4:0:10:0 [/sys/devices/pci0000:00/0000:00:05.0/0000:01:00.0/0000:02:0e.0/host4/target4:0:10/4:0:10:0] [4:2:0:0] disk DELL PERC 5/i 1.03 /dev/sda dir: /sys/bus/scsi/devices/4:2:0:0 [/sys/devices/pci0000:00/0000:00:05.0/0000:01:00.0/0000:02:0e.0/host4/target4:2:0/4:2:0:0] . lsmod: Module Size Used by fuse 66285 0 des_generic 16604 0 ecb 2209 0 md4 3461 0 nls_utf8 1455 0 cifs 278370 0 autofs4 26888 4 ipt_REJECT 2383 0 ip6t_REJECT 4628 2 nf_conntrack_ipv6 8748 2 nf_defrag_ipv6 12182 1 nf_conntrack_ipv6 xt_state 1492 2 nf_conntrack 79453 2 nf_conntrack_ipv6,xt_state ip6table_filter 2889 1 ip6_tables 19458 1 ip6table_filter ipv6 322029 31 ip6t_REJECT,nf_conntrack_ipv6,nf_defrag_ipv6 bnx2 79618 0 ses 6859 0 enclosure 8395 1 ses dcdbas 9219 0 serio_raw 4818 0 sg 30124 0 iTCO_wdt 13662 0 iTCO_vendor_support 3088 1 iTCO_wdt i5000_edac 8867 0 edac_core 46773 3 i5000_edac i5k_amb 5105 0 shpchp 33482 0 ext4 364410 3 mbcache 8144 1 ext4 jbd2 88738 1 ext4 sd_mod 39488 3 crc_t10dif 1541 1 sd_mod sr_mod 16228 0 cdrom 39771 1 sr_mod megaraid_sas 77090 2 aic79xx 129492 0 scsi_transport_spi 26151 1 aic79xx pata_acpi 3701 0 ata_generic 3837 0 ata_piix 22846 0 radeon 1023359 1 ttm 70328 1 radeon drm_kms_helper 33236 1 radeon drm 230675 3 radeon,ttm,drm_kms_helper i2c_algo_bit 5762 1 radeon i2c_core 31276 4 radeon,drm_kms_helper,drm,i2c_algo_bit dm_mirror 14101 0 dm_region_hash 12170 1 dm_mirror dm_log 10122 2 dm_mirror,dm_region_hash dm_mod 81500 11 dm_mirror,dm_log blkid: /dev/sda1: UUID="bc4777d9-ae2c-4c58-96ea-cedb342b8338" TYPE="ext4" /dev/sda2: UUID="j2wRZr-Mlko-QWBR-BndC-V2uN-vdhO-iKCuYu" TYPE="LVM2_member" /dev/mapper/vg_lal2server-lv_root: UUID="9238208a-1daf-4c3c-aa9b-469f0387ebee" TYPE="ext4" /dev/mapper/vg_lal2server-lv_swap: UUID="dbefb39c-5871-4bc9-b767-1ef18f12bd3d" TYPE="swap" /dev/mapper/vg_lal2server-lv_home: UUID="ec698993-08b7-443e-84f0-9f9cb31c5da8" TYPE="ext4" dmesg shows: megaraid_sas: fw state:c0000000 megasas: fwstate:c0000000, dis_OCR=0 scsi2 : LSI SAS based MegaRAID driver scsi 2:0:0:0: Direct-Access SEAGATE ST3146855SS S527 PQ: 0 ANSI: 5 scsi 2:0:1:0: Direct-Access SEAGATE ST3146855SS S527 PQ: 0 ANSI: 5 scsi 2:0:2:0: Direct-Access SEAGATE ST3146855SS S527 PQ: 0 ANSI: 5 scsi 2:0:3:0: Direct-Access SEAGATE ST3146855SS S527 PQ: 0 ANSI: 5 scsi 2:0:4:0: Direct-Access HITACHI HUS154545VLS300 D590 PQ: 0 ANSI: 5 scsi 2:0:5:0: Direct-Access HITACHI HUS154545VLS300 D590 PQ: 0 ANSI: 5 scsi 2:0:8:0: Direct-Access FUJITSU MBA3073RC D305 PQ: 0 ANSI: 5 scsi 2:0:9:0: Direct-Access FUJITSU MBA3073RC D305 PQ: 0 ANSI: 5 i.e. the 3 RAID Arrays Seagate Hitatchi and Fujitsu hard drives respectively. FURTHER UPDATE I have installed the megaraid storage manager console and connected to the server. It appears that the two CentOS installation hard drives are OK. The other 6 drives, one raid array of 4 and one raid array of 2 disks. The other drives are listed as (Foreign) Unconfigured Good.

Read the article
HP Proliant DL360 G5 + MSA50 RAID Setup recommendations

- by JohnRB

I am running a HP Proliant DL360 2 x 3GHz Xeon 16GB Ram P400 integrated RAID card with 6 x 73GB SAS HDDs running Ubuntu Server 14.04 CLI only. I recently got my hands on a MSA50 SAS Enclosure (10 x SAS HDD bays w/ SAS in/out interface) and wondering what you guys recommended as far as an addon raid controller for one of the pciex slots. I have both slots free Full and Half sizes. Any suggestions are greatly appreciated, I am an I.T. Consultant but have not used these particular units before so I was hoping to hear from someone who has. Thanks!

Read the article
HP DL380 G5 Predictive Drive Failure on a new drive

- by CharlieJ

Consolidated Error Report: Controller: Smart Array P400 in slot 3 Device: Physical Drive 1I:1:1 Message: Predictive failure. We have an HP DL380 G5 server with two 72GB 15k SAS drives configured in RAID1. A couple weeks ago, the server reported a drive failure on Drive 1. We replaced the drive with a brand new HDD -- same spares number. A few days ago, the server started reporting a predictive drive failure on the new drive, in the same bay. Is it likely the new drive is bad... or more likely we have a bay failure problem? This is a production server, so any advice would be appreciated. I have another spare drive, so I can hot swap it if this is a fluke and new drive is just bad. THANKS! CharlieJ

Read the article
OpenVPN Configuration - Windows 7 client & debian server

- by Guillaume

I recently formatted my Windows 7 computer and lost my client's config files for OpenVPN. I recovered the certificates and default config that were left on the server but I haven't managed to make the whole thing work again. I assume the server's config and routing table are OK because it was working before (although quite some time ago). Would any of you experts be able to help? server.conf # Serveur TCP/666 mode server proto udp port 666 dev tun # Cles et certificats ca ca.crt cert server.crt key server.key dh dh1024.pem tls-auth ta.key 0 cipher AES-256-CBC # Reseau server 10.8.0.0 255.255.255.0 #push "redirect-gateway def1 bypass-dhcp" push "dhcp-option DNS 208.67.222.222" push "dhcp-option DNS 208.67.220.220" push "redirect-gateway def1" keepalive 10 120 # Securite user nobody group nogroup chroot /etc/openvpn/jail persist-key persist-tun comp-lzo # Log verb 3 mute 20 status openvpn-status.log log-append /var/log/openvpn.log client.conf # Client client dev tun proto udp remote *my server's ip address*:666 cipher AES-256-CBC # Cles ca ca.crt cert client1.crt key client1.key tls-auth ta.key 1 # Securite nobind persist-key persist-tun comp-lzo verb 3 Routing table on debian server when OpenVPN server is running: Destination Gateway Genmask Indic Metric Ref Use Iface 10.8.0.2 * 255.255.255.255 UH 0 0 0 tun0 10.8.0.0 10.8.0.2 255.255.255.0 UG 0 0 0 tun0 my server's ip * 255.255.255.0 U 0 0 0 eth0 default 72815.trg.dedic 0.0.0.0 UG 0 0 0 eth0 Routing table on Windows 7 client (OpenVPN not working) =========================================================================== Interface List 19...00 f0 8a 1b 6e 5c ......TAP-Win32 Adapter V9 12...90 2e 34 33 84 7b ......Atheros AR8151 PCI-E Gigabit Ethernet Controller ( NDIS 6.20) 1...........................Software Loopback Interface 1 12...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter 13...00 00 00 00 00 00 00 e0 Teredo Tunneling Pseudo-Interface 16...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #2 =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.1.1 192.168.1.11 20 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 192.168.1.0 255.255.255.0 On-link 192.168.1.11 276 192.168.1.11 255.255.255.255 On-link 192.168.1.11 276 192.168.1.255 255.255.255.255 On-link 192.168.1.11 276 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 192.168.1.11 276 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 192.168.1.11 276 =========================================================================== Persistent Routes: None IPv6 Route Table =========================================================================== Active Routes: [...] =========================================================================== Persistent Routes: None And when the link is established between my client and the server: The server's routing table stays the same. The client's becomes: =========================================================================== Interface List 19...00 f0 8a 1b 6e 5c ......TAP-Win32 Adapter V9 12...90 2e 34 33 84 7b ......Atheros AR8151 PCI-E Gigabit Ethernet Controller ( NDIS 6.20) 1...........................Software Loopback Interface 1 12...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter 13...00 00 00 00 00 00 00 e0 Teredo Tunneling Pseudo-Interface 16...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #2 =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.1.1 192.168.1.11 20 0.0.0.0 128.0.0.0 10.8.0.5 10.8.0.6 30 10.8.0.1 255.255.255.255 10.8.0.5 10.8.0.6 30 10.8.0.4 255.255.255.252 On-link 10.8.0.6 286 10.8.0.6 255.255.255.255 On-link 10.8.0.6 286 10.8.0.7 255.255.255.255 On-link 10.8.0.6 286 my server's ip 255.255.255.255 192.168.1.1 192.168.1.11 20 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 128.0.0.0 128.0.0.0 10.8.0.5 10.8.0.6 30 192.168.1.0 255.255.255.0 On-link 192.168.1.11 276 192.168.1.11 255.255.255.255 On-link 192.168.1.11 276 192.168.1.255 255.255.255.255 On-link 192.168.1.11 276 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 192.168.1.11 276 224.0.0.0 240.0.0.0 On-link 10.8.0.6 286 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 192.168.1.11 276 255.255.255.255 255.255.255.255 On-link 10.8.0.6 286 =========================================================================== Persistent Routes: None What's working: Server and client do connect to each other, SSL certificates are OK. The client gets an IP (10.8.0.6) from the server OpenVPN client is started as an administrator. But: I cannot ping the other one on either side. 'Gateway' value is empty on client's side (in the adapter's "status" window). Client has got no internet access when the link is up. Ideal configuration: I only want the client to be able to use the server's Internet access and access its resources (MySQL server in particular). I do not need or want the server to access the client's local network. The client needs to be able to access it's local network, although all Internet traffic should be redirected to the VPN link. I spent a considerable amount of time on this but it's still not working, any help would be much appreciated. Thanks :)

Read the article
FreeNas running on ESXi - sometimes gets very slugish.

- by Luma

Hello everyone, I have a ESXi server (dual quad core, 8GB of DDR3 ram, 6x 1TB WD Blacks running in RAid 5 on the PErc 6/i controller. I have a 64bit freenas VM running, on this VM I keep about 200Gigs of stuff that my windows machines access. every now and then the throughput of this VM just dies, for example right now it can't even handle streaming a song and when I tried to transfer a folder the speed goes from 10-400KB/s. Might I add at this point that the ESXi box has dual gigabit network cards plugged into a good solid gigabit switch and other linux and windows VM's are just fine I have seen speeds over 90MB/s (frequently) The server still has ram left over (plenty actually) and cpu is very low (500-1000mhz) any ideas what could cause this? thanks. Luc

Read the article
Laptop stopped recognizing USB hard drive

- by vahokif

Hi, My Packard Bell EasyNote TX86 laptop stopped recognizing my 1 TB Toshiba Store Art hard drive. It worked fine until now, and it still works on other computers. Other USB devices (including storage) work, and I've tried plugging it in every port, to no avail. When I plug it in it spins up, but Windows doesn't react at all (it's not in disk management), Linux doesn't write anything in dmesg and I can't see it in BIOS setup. I didn't use it at all today, apart from plugging it into a freshly-installed Windows 7 machine once (where it worked). What can I do? Which device is to blame here? EDIT: One more thing. I unplugged the drive while the laptop was hibernated. Google says this might be the problem and it might have something to do with resetting the USB Host Controller.

Read the article
Wireless router not connection -> AP Not associated

- by candido

I can not connect to internet by wireless router after some months with ubuntu 10.04. I can connect with the same portable but with win OS. My SO is ubuntu 10.04 linux 2.6.32-41 arch SMP i686. The internet wireless network controller is Atheros AR9285 chipset (pci express) Kernel module ath9k I have tried a command line connection: $ sudo /etc/init.d/network-manager stop #stop gui network manager $ iwconfig wlan0 essid WLAN_3C key s:C001D20550B3C $ ifconfig Access Point: NOT-ASSOCIATED $dmesg ... AP 00:1a:2b:08:60:49 associated Is the SO has connected to router for booting long ( associated message), after boot and login why the connection to router is not possible by network-manager or command line (NOT associated message)? Thanks in advance

Read the article
Need advice to choose correct wi-fi drivers for Dell Vostro 3560

- by overdriven

I'm having problems with my Dell notebook's Wi-Fi, it can't see some of the available access points, despite they are close and I used to be connected to them yesterday. Other notebooks and my phone can see them. I believe it's a driver issue, since after installing system I haven't downloaded any network drivers. I went to Dell's website to search for them but I have no idea which should I choose. For my Dell Vostro 3560 and system Windows 8.1 64bit these are available: Intel Smart Connect Technology Application APP_iSCT_W8.1_A00_Setup-TJW84_ZPE.exe (23 MB) Vostro-3560_Network_Application_TJW84_WN_4.2.40.2418_A00.EXE (29 MB) Dell Wireless 1704 WLAN 802.11b/g/n (2.4GHz), Bluetooth v4.0+HS Driver DW1704_W8.1_A00_Setup-K1HGN_ZPE.exe (239 MB) Network_Driver_K1HGN_WN_6.30.223.143_A00.EXE (247 MB) Dell Wireless1703 802.11 b/g/n, BT4.0 + HS Driver Dell Wireless1901 802.11a/b/g/n (2.4GHz and 5GHz), Bluetooth v4.0+HS Driver DW1703_DW1901_Win8.1_A00_Setup-7FPWR_ZPE.exe (265 MB) Network_Driver_7FPWR_WN_10.0.0.263_A00.EXE (272 MB) Realtek RTL8105E/RTL8111E Ethernet Controller Driver LOM_Realtek_W8.1_A00_Setup-0XCVW_ZPE.exe (6 MB) Network_Driver_0XCVW_WN_8.018.0621.2013_A00.EXE (12 MB) Intel® Centrino® Wireless-N 2230 Bluetooth Driver BT_Intel_W8.14_A00_Setup-XR83W_ZPE.exe (31 MB) Network_Application_XR83W_WN_3.1.1307.0362_A00.EXE (37 MB)

Read the article
Unix domain socket firewall

- by lagab

Hello, everyone. I've got a problem with my debian server. Probably there is some vulnerable script at my web-serser, which is running from www-data user. I also have samba with winbind installed, and samba is joined to windows domain. So, probably this vulnerable script allows hacker to bruteforce out domain controller through winbind unix domain socket. Actually I have lots of such lines at netstat -a output: unix 3 [ ] STREAM CONNECTED 509027 /var/run/samba/winbindd_privileged/pipe And our DC logs contain lots of recorded authentication attems from root or guest accounts. How can I restrict my apaches access to winbind? I had an idea to use some kind of firewall for IPC sockets. Is it possible?

Read the article
Machine account authentication on Radius server

- by O.Shevchenko

My workstation is under Linux. I have an Active Directory domain controller + Radius server on Windows 2008. I can verify user account 'radius-01' using 'radtest' tool: $ radtest -t pap radius-01 password123 195.234.133.32 1812 password123 Sending Access-Request of id 98 to 195.234.73.2 port 1812 User-Name = "radius-01" User-Password = "password123" NAS-IP-Address = 127.0.1.1 NAS-Port = 1812 rad_recv: Access-Accept packet from host 195.234.133.32 port 1812, id=98, length=84 Framed-MTU = 1344 Framed-Protocol = PPP Service-Type = Framed-User Class = 0x537004f00000013700010200ac1c0... I have joined my Linux PC to Active Directory domain ARB-HRK using Samba: [root@shev-arb]# net ads testjoin Join is OK I can dump machine password: [root@shev-arb]# tdbdump /var/lib/samba/private/secrets.tdb { key(34) = "SECRETS/MACHINE_PASSWORD/ARB-HRK" data(15) = "yGgXJsquRnpT0g\00" } How can i authenticate my machine account on Radius server? Do anybody know any tools for this, like: radtest shev-arb$ yGgXJsquRnpT0g 195.234.133.32 1812 password123 (this command fails)

Read the article
LUNS access issue in ESX4 Cluster server

- by rmustafa

HI, I've created volumes in equallogic in PS 6000 XV(having 2 member which is in 1 pool), checked & those volumes can be easily detected my ISCSI software in windows. But the problem with ESX , not able to see the assigned disk on ESX server, I can explain what I've done: 1.Created Cluster with enabled HA & DRS 2.Added 3 ESX4 HOST 3.Added VMkernel & configured in all 3 ESX4, enabled vmotion & FT on the same adapter. 4.went to iSCSI storage adapter properties, enabled iSCSI 5.Trying to discover the available storage with the controller IP on dynamic discovery, but not able to see the assigned storage Note: the same volume is accessed to windows that means there is no issue from storage , am I right ???? Note: I wanted to mount the same volume in all 3 ESX host. Please suggest .... Thanks & Regards, Rashid Mustafa

Read the article
Windows Server 2008 R2 DNS Server not working?

- by wolfvilleian

I have a server running Windows Server 2008 R2 hosting a DNS server, exchange 2010 and is a domain controller. One computer on the network (and domain) can ping the server 25% of the time, also when I try to ping it's own hostname it also does not work. However another computer that is on the domain can ping it fine, and another computer on the network but not domain can ping fine as well. The computer that cannot ping the server is setup to use the DNS server running on the server only (secondary dns points to nothing) and it will resolve the hostname of the server to the external IP not internal when the other two computers correctly resolve the internal All 3 computers and server are connected directly into the same switch. Does anyone have any ideas on how to fix this? Thanks

Read the article
How to fix: mac keyboard ignores "first" key pressed

- by lexu

UPDATE 2012.03.19: the MBP described in this post is now broken and recycled (logic board fried). The replacement doesn't manifest the same problems. I tend to believe the problem originated in the keyboard firmware of the old MBP. Every now and then, usually after I haven't pressed a key in some time, sometimes minutes, sometimes seconds, my MBP will "swallow" the the first key I press ... say I'm logging into "superuser.com" .. I start typing my username and the textbox will show "exu" instead of "lexu" This is driving me nuts! My guess is the keyboard or it's controller goes to sleep and fails to wake up propperly ... What can I do about this? PS: I've already installed "MacBook, MacBook Pro Keyboard Firmware Update 1.0"

Read the article
Setting up Kerberos SSO in Windows 2008 network

- by Arturs Licis

We recently introduced Kerberos (SPNEGO) Single Sign-on in our web-portal, and tested it on a Windows network with Windows 2003 domain controller. Now, trying to test it on Windows 2008 R2 controlled network, SSO just doesn't work due to defective tokens. Up to the moment I was pretty sure that there's something wrong about environment and that were NTLM tokens. We double checked IE settings etc, but nothing helped. Then we checked the following settings for both users (logged on a client test-machine, and the one used as a Service Principal): This account supports Kerberos AES 128 bit encryption. This account supports Kerberos AES 256 bit encryption. .. and error message changed to ' GSSException: Failure unspecified at GSS-API level (Mechanism level: Encryption type AES256CTS mode with HMAC SHA1-96 is not supported/enabled) It makes me think that Internet Explorer receives Kerberos tokens at all times, and there's just some configuration missing, or it was ktpass.exe to be incorrectly executed. Here's how ktpass.exe was invoked: C:ktpass /out portal1.keytab /mapuser USER /princ HTTP/[email protected] /pass *

Read the article
b43 module loaded, but no interface showed up

- by Eduardo Bezerra

I'm using CentOS 6.3 x86_64 on a hardware with a BCM43224 chip for wi-fi. I installed the b43-fwcutter module and then run modprobe b43, with no error messages. However, no new network interface showed up, and the return of iwconfig is: lo no wireless extensions. eth0 no wireless extensions. lspci -nn | grep 43224 returns: 03:00.0 Network controller [0280]: Broadcom Corporation BCM43224 802.11a/b/g/n [14e4:4353] (rev 01) and uname -a: Linux localhost.localdomain 2.6.32-279.14.1.el6.x86_64 #1 SMP Tue Nov 6 23:43:09 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux Any ideas of how to make the wireless device work?

Read the article
IE does not send NTLM domain

- by Buddy Casino

Hi! I have a problem with NTLM single-sign-on with IE8. We've got multiple domain controllers and users from multiple domains that we try to authenticate to a web application via NTLMv1 passthru. Somehow IE fails to send the user's domain in the NTLM Type 1 message. This has the effect that the webapp can not match users properly to their domain controllers, resulting in failed logon attempts, because a user from domain X tries to authenticate to domain controller Y. This problem does not occur with Firefox, as it always sends the correct domain header. So: how do I get IE to send the domain in the NTLM header? Grateful for any help, Michael

Read the article

< Previous Page | 264 265 266 267 268 269 270 271 272 273 274 275 | Next Page >