Search Results

Search found 22460 results on 899 pages for 'azure service bus'.

Page 271/899 | < Previous Page | 267 268 269 270 271 272 273 274 275 276 277 278  | Next Page >

• How to connect two ubuntu computers with ethernet cable

  - by Lukasz Zaroda

  I'm trying to connect with ethernet cable two computers - desktop and laptop. What I want to do is transfer a lot of data from one to another. The problem is that I'm doing everything from: How to network two Ubuntu computers using ethernet (without a router)? But after that, ping always gives me "Destination host unreachable". I was searching a while but couldn't figure out what is a reason it doesn't work, maybe it's something about my devices or maybe someone will have another idea. Ethernet cable I got with my router. There is a text printed on it: Aurit Data Cable Cat.5 UTP 26AWG 4PAIR AWM PUC 75°C EIA/TIA 568B It's connecting now my desktop to router, so I can send this question. My desktop: System: Ubuntu 12.04 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller (rev 03) "ethtool -i eth0" output: driver: r8169 version: 2.3LK-NAPI firmware-version: rtl_nic/rtl8168d-1.fw bus-info: 0000:01:00.0 supports-statistics: yes supports-test: no supports-eeprom-access: no supports-register-dump: yes My laptop: System: Ubuntu 14.04 Ethernet controller: Qualcomm Atheros AR8162 Fast Ethernet (rev 08) "ethtool -i eth0" output: driver: alx version: firmware-version: bus-info: 0000:01:00.0 supports-statistics: no supports-test: no supports-eeprom-access: no supports-register-dump: no supports-priv-flags: no My iptables are accepting everything. Any ideas why I cannot reach other computer?

  Read the article

• Struggles to connect to network when using WPA with a BCM43225

  - by pst007x

  When booting my laptop, it will try to connect to my wireless network, however a window keeps popping up asking me for my security password, which has already been saved. I have to keep deleting my network settings, and reconnecting, otherwise it keeps failing to connect. My wireless is set up with a WPA, I do not want to lower my security because of this, but it is a pain and can take me 15mins plus to finally connect. The problem has only become apparent since a fresh install of 11.10. IPV6 disabled. System info: 01:00.0 Ethernet controller: Broadcom Corporation NetLink BCM57780 Gigabit Ethernet PCIe (rev 01) Subsystem: Acer Incorporated [ALI] Device 036d Flags: bus master, fast devsel, latency 0, IRQ 43 Memory at b3400000 (64-bit, non-prefetchable) [size=64K] Capabilities: <access denied> Kernel driver in use: tg3 Kernel modules: tg3 02:00.0 Network controller: Broadcom Corporation BCM43225 802.11b/g/n (rev 01) Subsystem: Broadcom Corporation Device 04da Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at b2400000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: brcmsmac Kernel modules: wl, brcmsmac ADDITIONAL: In terminal I get this: pst007x@pst007x-ubuntu64:~$ nm-applet start ** Message: applet now removed from the notification area ** (nm-applet:2816): DEBUG: old state indicates that this was not a disconnect 0 ** Message: using fallback from indicator to GtkStatusIcon ** Message: applet now embedded in the notification area ** Message: No keyring secrets found for Auto Access 01/802-11-wireless-security; asking user. ** (nm-applet:2816): DEBUG: foo_client_state_changed_cb Note this line: ** Message: No keyring secrets found for Auto Access 01/802-11-wireless-security; asking user. At this point is where I am asked for the password. Please report WPA issues with Ubuntu 11.10 here: https://bugs.launchpad.net/ubuntu/+source/network-manager/+bug/892727

  Read the article

• Oracle MAA Part 1: When One Size Does Not Fit All

  - by JoeMeeks

  The good news is that Oracle Maximum Availability Architecture (MAA) best practices combined with Oracle Database 12c (see video) introduce first-in-the-industry database capabilities that truly make unplanned outages and planned maintenance transparent to users. The trouble with such good news is that Oracle’s enthusiasm in evangelizing its latest innovations may leave some to wonder if we’ve lost sight of the fact that not all database applications are created equal. Afterall, many databases don’t have the business requirements for high availability and data protection that require all of Oracle’s ‘stuff’. For many real world applications, a controlled amount of downtime and/or data loss is OK if it saves money and effort. Well, not to worry. Oracle knows that enterprises need solutions that address the full continuum of requirements for data protection and availability. Oracle MAA accomplishes this by defining four HA service level tiers: BRONZE, SILVER, GOLD and PLATINUM. The figure below shows the progression in service levels provided by each tier. Each tier uses a different MAA reference architecture to deploy the optimal set of Oracle HA capabilities that reliably achieve a given service level (SLA) at the lowest cost.  Each tier includes all of the capabilities of the previous tier and builds upon the architecture to handle an expanded fault domain. Bronze is appropriate for databases where simple restart or restore from backup is ‘HA enough’. Bronze is based upon a single instance Oracle Database with MAA best practices that use the many capabilities for data protection and HA included with every Oracle Enterprise Edition license. Oracle-optimized backups using Oracle Recovery Manager (RMAN) provide data protection and are used to restore availability should an outage prevent the database from being able to restart. Silver provides an additional level of HA for databases that require minimal or zero downtime in the event of database instance or server failure as well as many types of planned maintenance. Silver adds clustering technology - either Oracle RAC or RAC One Node. RMAN provides database-optimized backups to protect data and restore availability should an outage prevent the cluster from being able to restart. Gold raises the game substantially for business critical applications that can’t accept vulnerability to single points-of-failure. Gold adds database-aware replication technologies, Active Data Guard and Oracle GoldenGate, which synchronize one or more replicas of the production database to provide real time data protection and availability. Database-aware replication greatly increases HA and data protection beyond what is possible with storage replication technologies. It also reduces cost while improving return on investment by actively utilizing all replicas at all times. Platinum introduces all of the sexy new Oracle Database 12c capabilities that Oracle staff will gush over with great enthusiasm. These capabilities include Application Continuity for reliable replay of in-flight transactions that masks outages from users; Active Data Guard Far Sync for zero data loss protection at any distance; new Oracle GoldenGate enhancements for zero downtime upgrades and migrations; and Global Data Services for automated service management and workload balancing in replicated database environments. Each of these technologies requires additional effort to implement. But they deliver substantial value for your most critical applications where downtime and data loss are not an option. The MAA reference architectures are inherently designed to address conflicting realities. On one hand, not every application has the same objectives for availability and data protection – the Not One Size Fits All title of this blog post. On the other hand, standard infrastructure is an operational requirement and a business necessity in order to reduce complexity and cost. MAA reference architectures address both realities by providing a standard infrastructure optimized for Oracle Database that enables you to dial-in the level of HA appropriate for different service level requirements. This makes it simple to move a database from one HA tier to the next should business requirements change, or from one hardware platform to another – whether it’s your favorite non-Oracle vendor or an Oracle Engineered System. Please stay tuned for additional blog posts in this series that dive into the details of each MAA reference architecture. Meanwhile, more information on Oracle HA solutions and the Maximum Availability Architecture can be found at: Oracle Maximum Availability Architecture - Webcast Maximize Availability with Oracle Database 12c - Technical White Paper

  Read the article

• Missing driver ASUS PCE-N53 11n N600 PCI-E Adapter

  - by oyse

  I have problems with getting an Asus PCE-N53 11n N600 PCI-E Adapter card to work on my desktop computer. As far as I can tell no drivers are installed for the card. I know I can manually download the drivers directly from Asus, but I would rather not go that route. If there are anyone that knows about any packages or other things I can do to make this work would be much appreciated. Some systems details: $ lsb_release -a No LSB modules are available. Distributor ID: Ubuntu Description: Ubuntu 12.04.1 LTS Release: 12.04 Codename: precise $ sudo lshw -C network *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 06 serial: d4:3d:7e:03:b9:1d size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl8168e-3_0.0.4 03/27/12 ip=192.168.0.173 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:43 ioport:d000(size=256) memory:f2104000-f2104fff memory:f2100000-f2103fff *-network UNCLAIMED description: Network controller product: Ralink corp. vendor: Ralink corp. physical id: 0 bus info: pci@0000:04:00.0 version: 00 width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:f7100000-f710ffff $ lsmod Module Size Used by nvidia 12319264 51 vesafb 13844 1 snd_hda_codec_hdmi 32474 1 joydev 17693 0 bnep 18281 2 rfcomm 47604 0 bluetooth 180104 10 bnep,rfcomm snd_hda_codec_realtek 224173 1 snd_seq_midi 13324 0 ppdev 17113 0 snd_rawmidi 30748 1 snd_seq_midi usbhid 47199 0 hid 99559 1 usbhid nouveau 774641 0 parport_pc 32866 1 snd_hda_intel 33773 5 ttm 76949 1 nouveau snd_hda_codec 127706 3 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel drm_kms_helper 46978 1 nouveau drm 242038 3 nouveau,ttm,drm_kms_helper snd_seq_midi_event 14899 1 snd_seq_midi snd_hwdep 13668 1 snd_hda_codec snd_seq 61896 2 snd_seq_midi,snd_seq_midi_event i2c_algo_bit 13423 1 nouveau mxm_wmi 12979 1 nouveau wmi 19256 1 mxm_wmi mac_hid 13253 0 snd_pcm 97188 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec psmouse 97362 0 video 19596 1 nouveau snd_timer 29990 2 snd_seq,snd_pcm snd_seq_device 14540 3 snd_seq_midi,snd_rawmidi,snd_seq snd 78855 20 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_rawmidi,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_seq,snd_pcm,snd_timer,snd_seq_device serio_raw 13211 0 soundcore 15091 1 snd snd_page_alloc 18529 2 snd_hda_intel,snd_pcm mei 41616 0 lp 17799 0 parport 46562 3 ppdev,parport_pc,lp r8169 62099 0

  Read the article

• How do I get Graphics drivers / bluetooth / card reader working on an Acer Aspire V3-571G?

  - by Adam

  A couple of days ago I bought an Acer Aspire V3-571G laptop without a system installed on it. The only thing that was there was Linux Linpus. I created a bootable CD with Ubuntu 12.04 64-bit - I read that my processor was 64 bit and that it might be a good configuration for my gear (I'm not especially fluent with all the computer stuff, still trying to learn) and replaced Linpus with Ubuntu. Everything seemed to work fine, but there're few exceptions to that which came pass my way. My bluetooth doesn't work. It seems to be switched on, but when I check my system settings the button is actually off, and I can't drag it 'perminently' to the 'on' position. Tried a couple of commands I found on the net, none of them helped and there was no word whatsoever in my BIOS settings about enabling bluetooth. My card reader has some serious problems with copying more than one file at a time. I tried to put some music on my phone through a MicroSD card adapter (because my bluetooth doesn't work) and it got stuck every single time I copied an album on it. I'm not sure if all my drivers were properly installed, so I checked in the terminal if it could tell me sth about my graphics. typed: sudo lshw -c display and what i got was: *-display UNCLAIMED description: VGA compatible controller product: NVIDIA Corporation vendor: NVIDIA Corporation physical id: 0 bus info: pci@0000:01:00.0 version: a1 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vga_controller cap_list configuration: latency=0 resources: memory:b2000000-b2ffffff memory:a0000000-afffffff memory:b0000000-b1ffffff ioport:2000(size=128) *-display description: VGA compatible controller product: Ivy Bridge Graphics Controller vendor: Intel Corporation physical id: 2 bus info: pci@0000:00:02.0 version: 09 width: 64 bits clock: 33MHz capabilities: msi pm vga_controller bus_master cap_list rom configuration: driver=i915 latency=0 resources: irq:44 memory:b3000000-b33fffff memory:c0000000-cfffffff ioport:3000(size=64) As I said I'm no expert and not english-speaking generally, but it doesn't seem to be right. I've got a NVIDIA GeForce GT 640M.

  Read the article

• Discs in DVD Drive not being read

  - by I Heart Ubuntu

  Does anyone have an experience with Ubuntu that is no longer reading discs in the DVD drive? This is my first time Ubuntu does not see the disc :| The disc is fine and works on my other Ubuntu computers. The drive is there and powered. I can even type in eject in a terminal and the drive will open. Using the command: sudo lshw -C disk I am able to see info about my drive too. Actually BOTH of my internal DVD drives cannot read discs anymore. If the output is not readable below, here is the info in pastebin. http://pastebin.com/GqqSCTPw *-cdrom:0 description: DVD writer product: DVD_RW ND-3500AG vendor: _NEC physical id: 0.0.0 bus info: scsi@0:0.0.0 logical name: /dev/cdrom1 logical name: /dev/cdrw1 logical name: /dev/dvd1 logical name: /dev/dvdrw1 logical name: /dev/scd0 logical name: /dev/sr0 version: 2.1B serial: [_NEC DVD_RW ND-3500AG2.1B06022300BT-LIGGY capabilities: removable audio cd-r cd-rw dvd dvd-r configuration: ansiversion=5 status=nodisc *-cdrom:1 description: DVD-RAM writer product: CDDVDW SH-S222A vendor: TSSTcorp physical id: 0.1.0 bus info: scsi@0:0.1.0 logical name: /dev/cdrom logical name: /dev/cdrw logical name: /dev/dvd logical name: /dev/dvdrw logical name: /dev/scd1 logical name: /dev/sr1 version: SB01 capabilities: removable audio cd-r cd-rw dvd dvd-r dvd-ram configuration: ansiversion=5 status=nodisc

  Read the article

• BizTalk: Instance Subscription: Details

  - by Leonid Ganeline

  It has interesting behavior and it is not always what we are waiting for. An orchestration can be enlisted with many subscriptions. In other word it can have several Receive shapes. Usually the first Receive uses the Activation subscription but other Receives create the Instance subscriptions. [See “Publish and Subscribe Architecture” in MSDN] Here is a sample process. This orchestration has two receives. It is a typical Sequential Convoy. [See "BizTalk Server 2004 Convoy Deep Dive" in MSDN by Stephen W. Thomas]. Let's experiment started.   There are three typical scenarios. First scenario: everything is OK Activation subscription for the Sample message is created when the orchestration the SampleProcess is enlisted. The Instance subscription is created only when the SampleProcess orchestration instance is started and it is removed when the orchestration instance is ended. So far so good, the Message_2 was delivered exactly in this time interval and was consumed. Second scenario: no consumers Three Sample_2 messages were delivered. One was delivered before the SampleProcess was started and before the instance subscription was created. Second message was delivered in the correct time interval. The third one was delivered after the SampleProcess orchestration was ended and the instance subscription was removed. Note: ·         It was not the first Sample_2 was consumed. It was first in the queue but in was not waiting, it was suspended when it was delivered to the Message Box and didn’t have any subscribers at this moment. The first and the last Sample_2 messages were Suspended (Nonresumable) in the Message Box. For each of this message we have got two (!) service instances associated with this suspended message. One service instance has the ServiceClass of Messaging, and we can see its Error Description:   The second service instance has the ServiceClass of RoutingFailureReport, and we can see its Error Description:   Third scenario: something goes wrong Two Sample_2 messages were delivered. Both were delivered in the same interval when the SampleProcess orchestration was working and the instance subscription was created and was working too. First Sample_2 was consumed. The second Sample_2 has the subscription but the subscriber, the SampleProcess orchestration, will not consume it. After the SampleProcess orchestration is ended (And only after! I will discuss this in the next article.), it is suspended (Nonresumable). In this time only one service instance associated with this kind of scenario is suspended. This service instance has the ServiceClass of Orchestration, and we can see its Error Description: In the Message tab we will see the Sample_2 message in the Suspended (Resumable) status. Note: ·         This behavior looks ambiguous. We see here the orchestration consumes the extra message(s) and gets suspended together with those extra messages. These messages are not consumed in term of “processed by orchestration”. But they are consumed in term of the “delivered to the subscriber”. The receive shape in the orchestration is not received these extra messages. But these messages are routed to the orchestration.     Unified Sequential convoy  Now one more scenario. It is the unified sequential convoy. That means the activation subscription is for the same message type as it for the instance subscription. The Sample_2 message is now the Sample message. For simplicity the SampleProcess orchestration consumes only two Sample messages. Usually the orchestration consumes a lot of messages inside loop, but now it is only two of them. First message starts the orchestration, the second message goes inside this orchestration. Then the next pair of messages follows, and so on. But if the input messages follow in shorter intervals we have got the problem. We lost messages in unpredictable manner. Note: ·         Maybe the better behavior would be if the orchestration removes the instance subscription after the message is consumed, not in the end on the orchestration. Right now it is a “feature” of the BizTalk subscription mechanism.

  Read the article

• "Enable Wireless" option is disabled in network settings

  - by silenTK

  I'm using Ubuntu 11.10 (dual booted with Windows 7) but I'm unable to access Internet wireless even though I can do so on Windows 7. The output for rfkill list all is given below: rfkill list all 0: brcmwl-0: Wireless LAN Soft blocked: no Hard blocked: yes 1: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: no The output for sudo lshw -C network *-network DISABLED is: description: Wireless interface product: BCM4313 802.11b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: eth1 version: 01 serial: 11:11:11:11:11:11 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 latency=0 multicast=yes wireless=IEEE 802.11 resources: irq:16 memory:c2500000-c2503fff *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 05 serial: 22:22:22:22:22:22 size: 100Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8105e-1.fw latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:42 ioport:3000(size=256) memory:c0404000-c0404fff memory:c0400000-c0403fff Broadcom STA wireless driver is installed, activated, and currently in use. My laptop is a HP-Pavilion-g6-1004tx. My hardware switch is on. Enable Wireless option is also disabled in network settings.

  Read the article

• Copying photos from camera stalls - how to track down issue?

  - by Hamish Downer

  When I copy files from my camera (connected via USB) to the SSD in my laptop a few files get copied and then the copy stalls. I'm not sure why, any ideas or things to investigate appreciated, or bug reports to go and look at. I have read this answer - the camera (Canon 40D in case that matters) mounts fine using gvfs. I can see the photos in Nautilus, or in the terminal (in /run/user/username/gvfs/... ) and I can copy a few photos, but not many. Using the terminal or Nautilus the process hangs until the camera goes to sleep. Digikam fails to copy any at all, as does Rapid Photo Downloader. Shotwell did manage it in the end, but that is very much a work around for me. I have disabled thumbnail generation by nautilus. Load average stays about 1 while this is happening, while CPU usage is half idle, half wait (and a little user/sys for other programs). None of the programs at the top of the cpu list in top are related to copying photos. There is not much in the logs - from /var/log/syslog Dec 2 16:20:52 mishtop dbus[945]: [system] Activating service name='org.freedesktop.UDisks' (using servicehelper) Dec 2 16:20:52 mishtop dbus[945]: [system] Successfully activated service 'org.freedesktop.UDisks' Dec 2 16:21:24 mishtop kernel: [ 2297.180130] usb 2-2: new high-speed USB device number 4 using ehci_hcd Dec 2 16:21:24 mishtop kernel: [ 2297.314272] usb 2-2: New USB device found, idVendor=04a9, idProduct=3146 Dec 2 16:21:24 mishtop kernel: [ 2297.314278] usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 Dec 2 16:21:24 mishtop kernel: [ 2297.314283] usb 2-2: Product: Canon Digital Camera Dec 2 16:21:24 mishtop kernel: [ 2297.314287] usb 2-2: Manufacturer: Canon Inc. Dec 2 16:21:24 mishtop mtp-probe: checking bus 2, device 4: "/sys/devices/pci0000:00/0000:00:1d.7/usb2/2-2" Dec 2 16:21:24 mishtop mtp-probe: bus: 2, device: 4 was not an MTP device This problem has only started recently and I've had all the hardware for ages. I have also recently upgraded to 12.10, though I'm not sure if the problem started when I upgraded or after the upgrade. I also note this similar question but it is currently unanswered and I'm providing more detail

  Read the article

• Ubuntu 13.10 No Sound

  - by spiersie

  I was running 13.04 since last monday and just today i upgraded to 13.10, in both of these version i have not managed to get my sound working. I have gone into alsamixer and disabled auto mute and the volumes are up. However if somebody thinks they can help me fix this i will gladly follow any steps. Please lay specifically any terminal commands you need me to do to either show specs or solve the problem as i am not fluent with the linux commands, this desktop being my first system to run linux, starting last monday. blake@Blake-Ubuntu-PC:~$ lspci -v | grep -A7 -i "audio" 00:01.1 Audio device: Advanced Micro Devices, Inc. [AMD/ATI] Trinity HDMI Audio Controller Subsystem: ASUSTeK Computer Inc. Device 8526 Flags: bus master, fast devsel, latency 0, IRQ 53 Memory at fef44000 (32-bit, non-prefetchable) [size=16K] Capabilities: Kernel driver in use: snd_hda_intel 00:10.0 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB XHCI Controller (rev 03) (prog-if 30 [XHCI]) 00:14.2 Audio device: Advanced Micro Devices, Inc. [AMD] FCH Azalia Controller (rev 01) Subsystem: ASUSTeK Computer Inc. Device 8445 Flags: bus master, slow devsel, latency 32, IRQ 16 Memory at fef40000 (64-bit, non-prefetchable) [size=16K] Capabilities: Kernel driver in use: snd_hda_intel 00:14.3 ISA bridge: Advanced Micro Devices, Inc. [AMD] FCH LPC Bridge (rev 11)

  Read the article

• Gigabyte u24f Touchpad (elantech) not detected

  - by user314973

  A new Ubuntu user here. I just installed Ubuntu 14.04 on my gigabyte U24F laptop. At first the touch-pad (I believe it's elantech) was working fine but one day I turned it off using fn+f10 key from the keyboard. The next day I could no longer turn it back on and it has since been undetected by the system. xinput returns Virtual core pointer id=2 [master pointer (3)] ? ? Virtual core XTEST pointer id=4 [slave pointer (2)] ? ? Logitech USB Optical Mouse id=11 [slave pointer (2)] ? Virtual core keyboard id=3 [master keyboard (2)] ? Virtual core XTEST keyboard id=5 [slave keyboard (3)] ? Power Button id=6 [slave keyboard (3)] ? Video Bus id=7 [slave keyboard (3)] ? Sleep Button id=8 [slave keyboard (3)] ? Video Bus id=9 [slave keyboard (3)] ? Power Button id=10 [slave keyboard (3)] ? AT Translated Set 2 keyboard id=12 [slave keyboard (3)] so there's no touch-pad detected. I'm using a USB mouse at the moment. Attempting to run synclient gives "Couldn't find synaptics properties. No synaptics driver loaded?" Things I've tried so far to no avail Reinstalling xserver-xorg-input-synaptics. Checking dconf.editor settings, touchpad is enabled. Booting into a live usb session, touchpad no longer even works in this case. (Does this mean a fresh install wouldn't even solve the problem?) Any help is greatly appreciated!

  Read the article

• Correct nvidia+intel graphics setup in 14.04

  - by Espressofa

  Just upgraded to 14.04 to try to fix some other issues. Now, something has gone wrong with my graphics. I have a Thinkpad T530 with Intel and Nvidia graphics cards. $ inxi -SGx System: Host: xyz Kernel: 3.13.0-24-generic x86_64 (64 bit, gcc: 4.8.2) Desktop: N/A Distro: Ubuntu 14.04 trusty Graphics: Card-1: Intel 3rd Gen Core processor Graphics Controller bus-ID: 00:02.0 Card-2: NVIDIA GF108M [NVS 5400M] bus-ID: 01:00.0 X.Org: 1.15.1 drivers: fbdev,vesa,intel,nouveau (unloaded: nvidia) Resolution: [email protected] GLX Renderer: N/A GLX Version: N/A Direct Rendering: N/A $ glxinfo name of display: :0 Xlib: extension "GLX" missing on display ":0". Xlib: extension "GLX" missing on display ":0". Xlib: extension "GLX" missing on display ":0". Xlib: extension "GLX" missing on display ":0". Xlib: extension "GLX" missing on display ":0". Error: couldn't find RGB GLX visual or fbconfig Xlib: extension "GLX" missing on display ":0". Xlib: extension "GLX" missing on display ":0". Xlib: extension "GLX" missing on display ":0". Xlib: extension "GLX" missing on display ":0". Error: couldn't find RGB GLX visual or fbconfig Xlib: extension "GLX" missing on display ":0". Xlib: extension "GLX" missing on display ":0". Xlib: extension "GLX" missing on display ":0". Xlib: extension "GLX" missing on display ":0". Xlib: extension "GLX" missing on display ":0". I'm not sure what I did but now something is wrong with my graphics, as should be visible from the above commands. nvidia-detector says "none" as well. I used to have bumblebee but then some website said to remove it and now something's clearly wrong. What's the right way to set things up? Should I try to add bumblebee back? Here's what's installed now: $ dpkg --get-selections | grep nvidia nvidia-319 install nvidia-331 install nvidia-libopencl1-331 install nvidia-opencl-icd-331 install nvidia-prime install nvidia-settings install nvidia-settings-319 install

  Read the article

• System speakers not recognized

  - by Kyle Maxwell

  Since upgrading to Xubuntu 13.10, sound has not functioned properly (e.g. screeching when playing Skype notifications). Now, however, it does not function at all. pavucontrol only shows Dummy Output and does not recognize the built-in speakers on my Dell Precision M4600. Possibly related, the sound indicator applet does not come up when I click on it, only showing a small white bar underneath it. I have purged and reinstalled pulseaudio. lspci -v shows: 00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 04) Subsystem: Dell Precision M4600 Flags: bus master, fast devsel, latency 0, IRQ 56 Memory at f2560000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: snd_hda_intel 01:00.1 Audio device: NVIDIA Corporation GF106 High Definition Audio Controller (rev a1) Subsystem: Dell Device 14a3 Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at f0080000 (32-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: snd_hda_intel The "Capabilities: <access denied" line makes me wonder if there's a permissions issue, as the Log Out applet now shows "Restart" and "Shutdown" grayed out. groups shows me in: kmaxwell adm dialout cdrom sudo dip plugdev fuse lpadmin netdev sambashare vboxusers

  Read the article

• Wireless doesn't work after installing 11.10

  - by Ingram

  I just did a fresh install of 11.10 32 bit and I can't get my wireless to work. I installed the drivers the Broadcom STA wireless drivers through additional drivers and rebooted, but it still doesn't see any wireless networks Did something change in 11.10 that makes the wireless card not work anymore? I was using 10.10 before, and it worked fine. Do I need to go back to 10.10? sudo lshw -C network [sudo] password for user1: *-network description: Ethernet interface product: NetLink BCM5784M Gigabit Ethernet PCIe vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 10 serial: 00:1f:16:be:55:ff size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.119 duplex=full firmware=sb v2.19 ip=192.168.0.70 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:43 memory:f0300000-f030ffff *-network UNCLAIMED description: Network controller product: BCM4311 802.11b/g WLAN vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:09:00.0 version: 01 width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:f0400000-f0403fff

  Read the article

• Unable to mount an LVM Hard-drive after upgrade

  - by Bruce Staples

  I imagine this is a basic gotcha ... but I can't see it. I have a system with 2(physical) harddrives. The boot system (/dev/sda) was running 10.04 & the second drive (/dev/sdb) was just a mounted filesystem. I did a clean load of Ubuntu 12.04 overwriting /dev/sda (not an upgrade) & now cannot mount the second drive. so I do not know what to enter it into the fstab ... I had expected to use: /dev/sdb /tera ext4 defaults 0 2 But even manual mounting fails (I also have tried various "-t" options on the off chance!) sudo mount -t ext4 /dev/sdb1 /tera mount: wrong fs type, bad option, bad superblock on /dev/sdb1, missing codepage or helper program, or other error In some cases useful info is found in syslog - try dmesg | tail or so Output from disk queries indicate that it is a Linux LVM & a healthy disk still. sudo lshw -C disk *-disk:0 description: ATA Disk product: WDC WD5000AACS-0 vendor: Western Digital physical id: 0 bus info: scsi@2:0.0.0 logical name: /dev/sda version: 01.0 serial: WD-WCASU1401098 size: 465GiB (500GB) capabilities: partitioned partitioned:dos configuration: ansiversion=5 signature=00015a55 *-disk:1 description: ATA Disk product: WDC WD10EADS-00L vendor: Western Digital physical id: 1 bus info: scsi@3:0.0.0 logical name: /dev/sdb version: 01.0 serial: WD-WCAU47836304 size: 931GiB (1TB) capabilities: partitioned partitioned:dos configuration: ansiversion=5 sudo fdisk -l Disk /dev/sda: 500.1 GB, 500106780160 bytes 255 heads, 63 sectors/track, 60801 cylinders, total 976771055 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00015a55 Device Boot Start End Blocks Id System /dev/sda1 * 2048 972580863 486289408 83 Linux /dev/sda2 972582910 976769023 2093057 5 Extended /dev/sda5 972582912 976769023 2093056 82 Linux swap / Solaris Disk /dev/sdb: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Device Boot Start End Blocks Id System /dev/sdb1 1 1953525167 976762583+ 8e Linux LVM LVM doesn't appear to be an option for mount or fstab. ... and here's a Smart data Screenshot from Disk Utility.

  Read the article

• Dell inspiron not finding Vodafone router

  - by Jeggy

  I have a "Dell inspiron 1564" and ubuntu doesn't find my friends router it works great at home, he has a vodafone router jeggy@jeggy-XPS:~$ sudo lshw -C network *-network description: Wireless interface product: BCM4312 802.11b/g LP-PHY vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:04:00.0 logical name: eth1 version: 01 serial: 78:e4:00:2a:d1:eb width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 latency=0 multicast=yes wireless=IEEE 802.11bg resources: irq:17 memory:f0200000-f0203fff *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 02 serial: b8:ac:6f:67:32:52 size: 10Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=N/A latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:42 ioport:3000(size=256) memory:f0410000-f0410fff memory:f0400000-f040ffff memory:f0420000-f043ffff *-network description: Ethernet interface physical id: 4 logical name: ham0 serial: 7a:79:05:ff:3e:ec size: 10Mbit/s capabilities: ethernet physical configuration: autonegotiation=off broadcast=yes driver=tun driverversion=1.6 duplex=full firmware=N/A ip=5.255.62.236 link=yes multicast=yes port=twisted pair speed=10Mbit/s

  Read the article

• How do I disable touchpad tap to click?

  - by AWE

  You've heard this a million times but the "tap to click" is a pain in the behind and I want to disable it. There is no touchpad in gpointing-device-settings and neither in mouse and touchpad in system settings. I've tried some commands in terminal but it's all crap. Dconf-editor doesn't react. How about solving this once and for all? xinput list: ? Virtual core pointer id=2 [master pointer (3)] ? ? Virtual core XTEST pointer id=4 [slave pointer (2)] ? ? PS/2 Generic Mouse id=13 [slave pointer (2)] ? Virtual core keyboard id=3 [master keyboard (2)] ? Virtual core XTEST keyboard id=5 [slave keyboard (3)] ? Power Button id=6 [slave keyboard (3)] ? Video Bus id=7 [slave keyboard (3)] ? Video Bus id=8 [slave keyboard (3)] ? Power Button id=9 [slave keyboard (3)] ? Sleep Button id=10 [slave keyboard (3)] ? Laptop_Integrated_Webcam_HD id=11 [slave keyboard (3)] ? AT Translated Set 2 keyboard id=12 [slave keyboard (3)] ? Dell WMI hotkeys id=14 [slave keyboard (3)]

  Read the article

• CUDA & MSI GT60 with Optimus enabled GTX670M?

  - by user1076693

  I have a MSI GT60 Laptop with an Optimus enabled GTX 670M GPU, and I have been trying to get CUDA going in Ubuntu 12.04 environment. I realize that Optimus is not supported in Linux, but I have read the following post suggesting that CUDA works for hybrid GPUs. How can I get nVidia CUDA or OpenCL working on a laptop with nVidia discrete card/Intel Integrated Graphics? I installed the NVIDIA driver via sudo add-apt-repository ppa:ubuntu-x-swat/x-updates sudo apt-get update sudo apt-get install nvidia-current The resulting driver version is 302.17, and supposedly GTX 670M is supported since 295.59. I also downloaded CUDA 4.2 from the NVIDIA site, and compiled it against nvidia-current libraries. Unfortunately, when I run deviceQuery in the CUDA SDK, I get the following output cudaGetDeviceCount returned 38 -> no CUDA-capable device is detected Checking /proc/driver/nvidia/gpus/0/information gives the following Model: GeForce GTX 670M IRQ: 16 GPU UUID: GPU-????????-????-????-????-???????????? Video BIOS: ??.??.??.??.?? Bus Type: PCI-E DMA Size: 32 bits DMA Mask: 0xffffffffff Bus Location: 0000:01.00.0 Here is the output of "lspci | grep VGA" 00:02.0 VGA compatible controller: Intel Corporation Ivy Bridge Graphics Controller (rev 09) 01:00.0 VGA compatible controller: NVIDIA Corporation Device 1213 (rev ff) So... what am I doing wrong? Thanks!

  Read the article

• wireless is disabled by hardware lenovo 3000g430

  - by sudheer

  sir i have problem with my wifi switch sir please tell me solution for my problem (wifi is disabled by hardware). output of sudo lshw -C network is sudo] password for sudheer: *-network DISABLED description: Wireless interface product: BCM4312 802.11b/g LP-PHY vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:06:00.0 logical name: eth2 version: 01 serial: 00:21:00:72:3a:93 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 latency=0 multicast=yes wireless=IEEE 802.11bg resources: irq:19 memory:f4700000-f4703fff *-network description: Ethernet interface product: NetLink BCM5906M Fast Ethernet PCI Express vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:07:00.0 logical name: eth0 version: 02 serial: 00:1e:68:ad:24:0b size: 100Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.121 duplex=full firmware=sb v3.04 ip=172.16.52.79 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:47 memory:f4600000-f460ffff output of iwconfig is lo no wireless extensions. eth2 IEEE 802.11 Access Point: Not-Associated Link Quality:5 Signal level:0 Noise level:0 Rx invalid nwid:0 invalid crypt:0 invalid misc:0 eth0 no wireless extensions. sudheer@sudheer:~$ sudo iwlistscanning sudo: iwlistscanning: command not found ***sudheer@sudheer:~$ sudo iwlist scanning*** lo Interface doesn't support scanning. eth2 Failed to read scan data : Invalid argument eth0 Interface doesn't support scanning.

  Read the article

• wireless card not detected

  - by user281219

  i have a old HP Compaq NX6125 with a new lunbuntu 14.04 32 bits install , but the wireless card is not working I have already done this steps and the wireless leds on the laptop are on but can't see any where the wireless interface , cloud`t do the last two steps . sudo apt-get remove bcmwl-kernel-source sudo apt-get install firmware-b43-installer b43-fwcutter Then Reboot And you need to activate the card from settings/network/wireless make it ON After this search for wireless icon at the task bar and look for your wifi. lshw -class network: *-network:0 description: Ethernet interface product: NetXtreme BCM5788 Gigabit Ethernet vendor: Broadcom Corporation physical id: 1 bus info: pci@0000:02:01.0 logical name: eth0 version: 03 serial: 00:0f:b0:f7:d1:0f size: 100Mbit/s capacity: 1Gbit/s width: 32 bits clock: 66MHz capabilities: pm vpd msi bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.134 duplex=full firmware=5788-v3.26 ip=192.168.1.120 latency=64 link=yes mingnt=64 multicast=yes port=twisted pair speed=100Mbit/s resources: irq:23 memory:d0000000-d000ffff *-network:1 description: Network controller product: BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller vendor: Broadcom Corporation physical id: 2 bus info: pci@0000:02:02.0 version: 02 width: 32 bits clock: 33MHz capabilities: bus_master configuration: driver=b43-pci-bridge latency=64 resources: irq:22 memory:d0010000-d0011fff *-network description: Wireless interface physical id: 1 logical name: wlan2 serial: 00:14:a5:77:9e:10 capabilities: ethernet physical wireless configuration: broadcast=yes driver=b43 driverversion=3.13.0-29-generic firmware=666.2 link=no multicast=yes wireless=IEEE 802.11bg

  Read the article

• BusEnum2 and a Minor Bug Fix

  - by Kate Moss' Open Space

  The default root bus driver, BusEnum, enumerate and active drivers one by one in synchronized manner. It is not only slowing the boot time but in the even if any of driver's init function (XXX_init) get hanged, the whole system won't boot at all. There is a sample of enhanced root bus driver, BusEnum2, on the http://msdn.microsoft.com/en-us/library/dd187254.aspx The page provides the sample code and the detail explanation of the design concept. With multi-threaded BusEnum2 on CE7 with SMP enabled system, the scalability is even more significant. Since you have more than one processor and it can load drivers in parallel! Everything looks good so far, except to there is a small bug in the sample code. Fortunately, it is easy to fix. But hard to trace if you ever enc outer it! The BUSENUM2 flag only defined in BUSENUM2\BUSDEF\sources but not in BUSENUM2\BUSENUM\sources. The DeviceFolder is implemented in BUSENUM2\BUSDEF but the instance is created in BUSENUM2\BUSENUM\busenum.cpp, so the result is it allocates less memory than actual need.   Add   CDEFINES=$(CDEFINES) -DBUSENUM2   into BUSENUM2\BUSENUM\sources and the problem fixed!

  Read the article

• Extension GLX missing...on a desktop PC

  - by Bart van Heukelom

  I just installed Ubuntu 12.10 on a new PC with an Nvidia GTX 560 graphics card, but after installing the Nvidia proprietary drivers (either -current or -current-updates), Unity won't start. When trying to start it manually I get the message "extension GLX missing". I've searched around and found results like this question which point out it's a problem with Nvidia Optimus laptops. However, I don't have this problem on a laptop, but on a desktop PC. lshw output for the graphics card: *-display description: VGA compatible controller product: GF114 [GeForce GTX 560 SE] vendor: NVIDIA Corporation physical id: 0 bus info: pci@0000:01:00.0 version: a1 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vga_controller bus_master cap_list rom configuration: driver=nouveau latency=0 resources: irq:16 memory:f4000000-f5ffffff memory:e0000000-e7ffffff memory:e8000000-ebffffff ioport:e000(size=128) memory:f6000000-f607ffff and CPU: *-cpu description: CPU product: Intel(R) Core(TM) i5-3570K CPU @ 3.40GHz vendor: Intel Corp. physical id: 40 bus info: cpu@0 version: Intel(R) Core(TM) i5-3570K CPU @ 3.40GHz slot: SOCKET 0 size: 1600MHz capacity: 3800MHz width: 64 bits clock: 100MHz capabilities: x86-64 fpu fpu_exception wp vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx rdtscp constant_tsc arch_perfmon pebs bts rep_good nopl xtopology nonstop_tsc aperfmperf pni pclmulqdq dtes64 monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr pdcm pcid sse4_1 sse4_2 popcnt tsc_deadline_timer aes xsave avx f16c rdrand lahf_lm ida arat epb xsaveopt pln pts dtherm tpr_shadow vnmi flexpriority ept vpid fsgsbase smep erms cpufreq configuration: cores=4 enabledcores=4 threads=4

  Read the article

• Internet Timeouts with TP-Link TL-WN821N v2 wireless usb stick

  - by user1622959

  A short time after accessing the internet, the browser/download times out. Before the timeout, the internet works OK briefly; afterwards, the wireless is still connected with a strong signal, but every internet access results in a timeout. When I leave the PC for a while, the internet is back just to timeout again as soon as I start using it. The same happens when I reconnect to the router. Also, when I surf the internet, it takes a couple of minutes until the timeout, but when I download something, it times out in a matter of seconds. The wireless adapter works just fine in Windows and internet via ethernet cable works just fine in Ubuntu. Does anyone have the same problem or knows a solution. I use Ubuntu 12.10 x64. The problem occurs since I installed ubuntu (which was a few days ago). Here some stuff that might be usefull: serus@serus-Ubuntu-PC:~$ lsusb Bus 002 Device 002: ID 0cf3:1002 Atheros Communications, Inc. TP-Link TL-WN821N v2 802.11n [Atheros AR9170] serus@serus-Ubuntu-PC:~$ lsmod Module Size Used by carl9170 82083 0 serus@serus-Ubuntu-PC:~$ modinfo carl9170 filename: /lib/modules/3.5.0-21- generic/kernel/drivers/net/wireless/ath/carl9170/carl9170.ko alias: arusb_lnx alias: ar9170usb firmware: carl9170-1.fw description: Atheros AR9170 802.11n USB wireless serus@serus-Ubuntu-PC:~$ iwconfig wlan0 IEEE 802.11bgn ESSID:"virginmedia0137463" Mode:Managed Frequency:2.462 GHz Access Point: A0:21:B7:F8:29:B6 Bit Rate=240 Mb/s Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=66/70 Signal level=-44 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:1399 Invalid misc:18 Missed beacon:0 serus@serus-Ubuntu-PC:~$ sudo lshw -C network *-network description: Wireless interface physical id: 1 bus info: usb@2:2 logical name: wlan0 serial: 00:27:19:bb:00:19 capabilities: ethernet physical wireless configuration: broadcast=yes driver=carl9170 driverversion=3.5.0-21-generic firmware=1.9.4 ip=192.168.0.6 link=yes multicast=yes wireless=IEEE 802.11bgn

  Read the article

• How much is a subscriber worth?

  - by Tom Lewin

  This year at Red Gate, we’ve started providing a way to back up SQL Azure databases and Azure storage. We decided to sell this as a service, instead of a product, which means customers only pay for what they use. Unfortunately for us, it makes figuring out revenue much trickier. With a product like SQL Compare, a customer pays for it, and it’s theirs for good. Sure, we offer support and upgrades, but, fundamentally, the sale is a simple, upfront transaction: we’ve made this product, you need this product, we swap product for money and everyone is happy. With software as a service, it isn’t that easy. The money and product don’t change hands up front. Instead, we provide a service in exchange for a recurring fee. We know someone buying SQL Compare will pay us $X, but we don’t know how long service customers will stay with us, or how much they will spend. How do we find this out? We use lifetime value analysis. What is lifetime value? Lifetime value, or LTV, is how much a customer is worth to the business. For Entrepreneurs has a brilliant write up that we followed to conduct our analysis. Basically, it all boils down to this equation: LTV = ARPU x ALC To make it a bit less of an alphabet-soup and a bit more understandable, we can write it out in full: The lifetime value of a customer equals the average revenue per customer per month, times the average time a customer spends with the service Simple, right? A customer is worth the average spend times the average stay. If customers pay on average $50/month, and stay on average for ten months, then a new customer will, on average, bring in $500 over the time they are a customer! Average spend is easy to work out; it’s revenue divided by customers. The problem comes when we realise that we don’t know exactly how long a customer will stay with us. How can we figure out the average lifetime of a customer, if we only have six months’ worth of data? The answer lies in the fact that: Average Lifetime of a Customer = 1 / Churn Rate The churn rate is the percentage of customers that cancel in a month. If half of your customers cancel each month, then your average customer lifetime is two months. The problem we faced was that we didn’t have enough data to make an estimate of one month’s cancellations reliable (because barely anybody cancels)! To deal with this data problem, we can take data from the last three months instead. This means we have more data to play with. We can still use the equation above, we just need to multiply the final result by three (as we worked out how many three month periods customers stay for, and we want our answer to be in months). Now these estimates are likely to be fairly unreliable; when there’s not a lot of data it pays to be cautious with inference. That said, the numbers we have look fairly consistent, and it’s super easy to revise our estimates when new data comes in. At the very least, these numbers give us a vague idea of whether a subscription business is viable. As far as Cloud Services goes, the business looks very viable indeed, and the low cancellation rates are much more than just data points in LTV equations; they show that the product is working out great for our customers, which is exactly what we’re looking for!

  Read the article

• How to help FGLRX detect a device

  - by user113416

  I have HD 4850 card, Ubuntu 12.10 and installed legacy drivers using makson96 ppa. The issue is, that FGLRX can not detect my device and loads vesa bios. I had the same problem on ubuntu 11.10, 12.04 versions. I want to manually help fglrx find a matching device to load as it shoudld do. It is interesting, why does fglrx search for a device in a PCI:0@1:0:1 Bus? in xorg.cof different bus is indicated: Section "Device" Identifier "aticonfig-Device[0]-0" Driver "fglrx" BusID "PCI:1:0:0" EndSection fglrxinfo display: :0.0 screen: 0 OpenGL vendor string: Advanced Micro Devices, Inc. OpenGL renderer string: ATI Radeon HD 4800 Series OpenGL version string: 3.3.11653 Compatibility Profile Context Here is a part of my xorg log: [ 3.846] (II) VESA: driver for VESA chipsets: vesa [ 3.846] (II) FBDEV: driver for framebuffer: fbdev [ 3.846] (++) using VT number 7 [ 3.846] (WW) Falling back to old probe method for fglrx [ 3.883] (II) Loading PCS database from /etc/ati/amdpcsdb [ 3.883] (--) Assigning device section with no busID to primary device [ 3.883] (--) Chipset Supported AMD Graphics Processor (0x9442) found [ 3.884] (WW) fglrx: No matching Device section for instance (BusID PCI:0@1:0:1) found [ 3.884] (II) AMD Video driver is running on a device belonging to a group targeted for this release [ 3.884] (II) AMD Video driver is signed [ 3.884] (II) fglrx(0): pEnt->device->identifier=0xb7791d8f [ 3.884] (WW) Falling back to old probe method for vesa [ 3.884] (WW) Falling back to old probe method for fbdev Thanks in advance.

  Read the article

< Previous Page | 267 268 269 270 271 272 273 274 275 276 277 278  | Next Page >