Search Results

Search found 21194 results on 848 pages for 'game state'.

Page 274/848 | < Previous Page | 270 271 272 273 274 275 276 277 278 279 280 281  | Next Page >

• HP to Cisco spanning tree root flapping

  - by Tim Brigham

  Per a recent question I recently configured both my HP (2x 2900) and Cisco (1x 3750) hardware to use MSTP for interoperability. I thought this was functional until I applied the change to the third device (HP switch 1 below) at which time the spanning tree root started flapping causing performance issues (5% packet loss) between my two HP switches. I'm not sure why. HP Switch 1 A4 connected to Cisco 1/0/1. HP Switch 2 B2 connected to Cisco 2/0/1. HP Switch 1 A2 connected to HP Switch 2 A1. I'd prefer the Cisco stack to act as the root. EDIT: There is one specific line - 'spanning-tree 1 path-cost 500000' in the HP switch 2 that I didn't add and was preexisting. I'm not sure if it could have the kind of impact that I'm describing. I'm more a security and monitoring guy then networking. EDIT 2: I'm starting to believe the problem lies in the fact that the value for my MST 0 instance on the Cisco is still at the default 32768. I worked up a diagram: This is based on every show command I could find for STP. I'll make this change after hours and see if it helps. Cisco 3750 Config: version 12.2 spanning-tree mode mst spanning-tree extend system-id spanning-tree mst configuration name mstp revision 1 instance 1 vlan 1, 40, 70, 100, 250 spanning-tree mst 1 priority 0 vlan internal allocation policy ascending interface TenGigabitEthernet1/1/1 switchport trunk encapsulation dot1q switchport mode trunk ! interface TenGigabitEthernet2/1/1 switchport trunk encapsulation dot1q switchport mode trunk ! interface Vlan1 no ip address ! interface Vlan100 ip address 192.168.100.253 255.255.255.0 ! Cisco 3750 show spanning tree: show spanning-tree MST0 Spanning tree enabled protocol mstp Root ID Priority 32768 Address 0004.ea84.5f80 Cost 200000 Port 53 (TenGigabitEthernet1/1/1) Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec Bridge ID Priority 32768 (priority 32768 sys-id-ext 0) Address a44c.11a6.7c80 Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec Interface Role Sts Cost Prio.Nbr Type ------------------- ---- --- --------- -------- -------------------------------- Te1/1/1 Root FWD 2000 128.53 P2p MST1 Spanning tree enabled protocol mstp Root ID Priority 1 Address a44c.11a6.7c80 This bridge is the root Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec Bridge ID Priority 1 (priority 0 sys-id-ext 1) Address a44c.11a6.7c80 Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec Interface Role Sts Cost Prio.Nbr Type ------------------- ---- --- --------- -------- -------------------------------- Te1/1/1 Desg FWD 2000 128.53 P2p Cisco 3750 show logging: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to down %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan100, changed state to down %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan100, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to down %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to up HP Switch 1: ; J9049A Configuration Editor; Created on release #T.13.71 vlan 1 name "DEFAULT_VLAN" untagged 1-8,10,13-16,18-23,A1-A4 ip address 100.100.100.17 255.255.255.0 no untagged 9,11-12,17,24 exit vlan 100 name "192.168.100" untagged 9,11-12,17,24 tagged 1-8,10,13-16,18-23,A1-A4 no ip address exit vlan 21 name "Users_2" tagged 1,A1-A4 no ip address exit vlan 40 name "Cafe" tagged 1,4,7,A1-A4 no ip address exit vlan 250 name "Firewall" tagged 1,4,7,A1-A4 no ip address exit vlan 70 name "DMZ" tagged 1,4,7-8,13,A1-A4 no ip address exit spanning-tree spanning-tree config-name "mstp" spanning-tree config-revision 1 spanning-tree instance 1 vlan 1 40 70 100 250 password manager password operator HP Switch 1 show spanning tree: show spanning-tree Multiple Spanning Tree (MST) Information STP Enabled : Yes Force Version : MSTP-operation IST Mapped VLANs : 2-39,41-69,71-99,101-249,251-4094 Switch MAC Address : 0021f7-126580 Switch Priority : 32768 Max Age : 20 Max Hops : 20 Forward Delay : 15 Topology Change Count : 363,490 Time Since Last Change : 14 hours CST Root MAC Address : 0004ea-845f80 CST Root Priority : 32768 CST Root Path Cost : 200000 CST Root Port : 1 IST Regional Root MAC Address : 0021f7-126580 IST Regional Root Priority : 32768 IST Regional Root Path Cost : 0 IST Remaining Hops : 20 Root Guard Ports : TCN Guard Ports : BPDU Protected Ports : BPDU Filtered Ports : PVST Protected Ports : PVST Filtered Ports : | Prio | Designated Hello Port Type | Cost rity State | Bridge Time PtP Edge ----- --------- + --------- ---- ---------- + ------------- ---- --- ---- A1 | Auto 128 Disabled | A2 10GbE-CX4 | 2000 128 Forwarding | 0021f7-126580 2 Yes No A3 10GbE-CX4 | Auto 128 Disabled | A4 10GbE-SR | Auto 128 Disabled | HP Switch 1 Logging: I removed the date / time fields since they are inaccurate (no NTP configured on these switches) 00839 stp: MSTI 1 Root changed from 0:a44c11-a67c80 to 32768:0021f7-126580 00839 stp: MSTI 1 Root changed from 32768:0021f7-126580 to 0:a44c11-a67c80 00842 stp: MSTI 1 starved for an MSTI Msg Rx on port A4 from 0:a44c11-a67c80 00839 stp: MSTI 1 Root changed from 0:a44c11-a67c80 to 32768:0021f7-126580 00839 stp: MSTI 1 Root changed from 32768:0021f7-126580 to 0:a44c11-a67c80 00839 stp: MSTI 1 Root changed from 0:a44c11-a67c80 to ... HP Switch 2 Configuration: ; J9146A Configuration Editor; Created on release #W.14.49 vlan 1 name "DEFAULT_VLAN" untagged 1,3-17,21-24,A1-A2,B2 ip address 100.100.100.36 255.255.255.0 no untagged 2,18-20,B1 exit vlan 100 name "192.168.100" untagged 2,18-20 tagged 1,3-17,21-24,A1-A2,B1-B2 no ip address exit vlan 21 name "Users_2" tagged 1,A1-A2,B2 no ip address exit vlan 40 name "Cafe" tagged 1,13-14,16,A1-A2,B2 no ip address exit vlan 250 name "Firewall" tagged 1,13-14,16,A1-A2,B2 no ip address exit vlan 70 name "DMZ" tagged 1,13-14,16,A1-A2,B2 no ip address exit logging 192.168.100.18 spanning-tree spanning-tree 1 path-cost 500000 spanning-tree config-name "mstp" spanning-tree config-revision 1 spanning-tree instance 1 vlan 1 40 70 100 250 HP Switch 2 Spanning Tree: show spanning-tree Multiple Spanning Tree (MST) Information STP Enabled : Yes Force Version : MSTP-operation IST Mapped VLANs : 2-39,41-69,71-99,101-249,251-4094 Switch MAC Address : 0024a8-cd6000 Switch Priority : 32768 Max Age : 20 Max Hops : 20 Forward Delay : 15 Topology Change Count : 21,793 Time Since Last Change : 14 hours CST Root MAC Address : 0004ea-845f80 CST Root Priority : 32768 CST Root Path Cost : 200000 CST Root Port : A1 IST Regional Root MAC Address : 0021f7-126580 IST Regional Root Priority : 32768 IST Regional Root Path Cost : 2000 IST Remaining Hops : 19 Root Guard Ports : TCN Guard Ports : BPDU Protected Ports : BPDU Filtered Ports : PVST Protected Ports : PVST Filtered Ports : | Prio | Designated Hello Port Type | Cost rity State | Bridge Time PtP Edge ----- --------- + --------- ---- ---------- + ------------- ---- --- ---- A1 10GbE-CX4 | 2000 128 Forwarding | 0021f7-126580 2 Yes No A2 10GbE-CX4 | Auto 128 Disabled | B1 SFP+SR | 2000 128 Forwarding | 0024a8-cd6000 2 Yes No B2 | Auto 128 Disabled | HP Switch 2 Logging: I removed the date / time fields since they are inaccurate (no NTP configured on these switches) 00839 stp: CST Root changed from 32768:0021f7-126580 to 32768:0004ea-845f80 00839 stp: IST Root changed from 32768:0021f7-126580 to 32768:0024a8-cd6000 00839 stp: CST Root changed from 32768:0004ea-845f80 to 32768:0024a8-cd6000 00839 stp: CST Root changed from 32768:0024a8-cd6000 to 32768:0004ea-845f80 00839 stp: CST Root changed from 32768:0004ea-845f80 to 32768:0024a8-cd6000 00435 ports: port B1 is Blocked by STP 00839 stp: CST Root changed from 32768:0024a8-cd6000 to 32768:0021f7-126580 00839 stp: IST Root changed from 32768:0024a8-cd6000 to 32768:0021f7-126580 00839 stp: CST Root changed from 32768:0021f7-126580 to 32768:0004ea-845f80

  Read the article

• Why my VPN doesn't work anymore?

  - by xx77aBs

  I have openvpn server running on debian lenny. There is only one client - and it is running Windows 7 64-bit. This has worked for few months without any problems. And now, let's say for the last 7 days, it doesn't work at all. I connect successfully from client to the server, but I can't access anything through VPN. I have set it up so that all internet traffic is routed through VPN, and now when I connect with the client, the client can't do anything on the net (open any webpage, ping google, anything ...). Can you help me to figure out what's wrong ? I don't know where to start. I've also tried to connect to another openvpn server (I've installed and configured openvpn on another server, and when I try to connect to it result is the same). So I think there's something wrong with client ... Here is my connection log: Wed Apr 04 21:35:59 2012 OpenVPN 2.3-alpha1 Win32-MSVC++ [SSL (OpenSSL)] [LZO2] [PF_INET6] [IPv6 payload 20110522-1 (2.2.0)] built on Feb 21 2012 Enter Management Password: Wed Apr 04 21:35:59 2012 MANAGEMENT: TCP Socket listening on [AF_INET]127.0.0.10:25340 Wed Apr 04 21:35:59 2012 Need hold release from management interface, waiting... Wed Apr 04 21:36:00 2012 MANAGEMENT: Client connected from [AF_INET]127.0.0.10:25340 Wed Apr 04 21:36:00 2012 MANAGEMENT: CMD 'state on' Wed Apr 04 21:36:00 2012 MANAGEMENT: CMD 'log all on' Wed Apr 04 21:36:00 2012 MANAGEMENT: CMD 'hold off' Wed Apr 04 21:36:00 2012 MANAGEMENT: CMD 'hold release' Wed Apr 04 21:36:00 2012 WARNING: No server certificate verification method has been enabled. See http://openvpn.net/howto.html#mitm for more info. Wed Apr 04 21:36:00 2012 NOTE: OpenVPN 2.1 requires '--script-security 2' or higher to call user-defined scripts or executables Wed Apr 04 21:36:00 2012 Socket Buffers: R=[8192->8192] S=[8192->8192] Wed Apr 04 21:36:00 2012 MANAGEMENT: >STATE:1333568160,RESOLVE,,, Wed Apr 04 21:36:00 2012 UDPv4 link local: [undef] Wed Apr 04 21:36:00 2012 UDPv4 link remote: [AF_INET]11.22.33.44:1234 Wed Apr 04 21:36:00 2012 MANAGEMENT: >STATE:1333568160,WAIT,,, Wed Apr 04 21:36:00 2012 MANAGEMENT: >STATE:1333568160,AUTH,,, Wed Apr 04 21:36:00 2012 TLS: Initial packet from [AF_INET]11.22.33.44:1234, sid=ee329574 f15e9e04 Wed Apr 04 21:36:00 2012 VERIFY OK: depth=1, C=US, ST=CA, L=SanFrancisco, O=Fort-Funston, CN=Fort-Funston CA, [email protected] Wed Apr 04 21:36:00 2012 VERIFY OK: depth=0, C=US, ST=CA, L=SanFrancisco, O=Fort-Funston, CN=server_key, [email protected] Wed Apr 04 21:36:01 2012 Data Channel Encrypt: Cipher 'BF-CBC' initialized with 128 bit key Wed Apr 04 21:36:01 2012 Data Channel Encrypt: Using 160 bit message hash 'SHA1' for HMAC authentication Wed Apr 04 21:36:01 2012 Data Channel Decrypt: Cipher 'BF-CBC' initialized with 128 bit key Wed Apr 04 21:36:01 2012 Data Channel Decrypt: Using 160 bit message hash 'SHA1' for HMAC authentication Wed Apr 04 21:36:01 2012 Control Channel: TLSv1, cipher TLSv1/SSLv3 DHE-RSA-AES256-SHA, 1024 bit RSA Wed Apr 04 21:36:01 2012 [server_key] Peer Connection Initiated with [AF_INET]11.22.33.44:1234 Wed Apr 04 21:36:02 2012 MANAGEMENT: >STATE:1333568162,GET_CONFIG,,, Wed Apr 04 21:36:03 2012 SENT CONTROL [server_key]: 'PUSH_REQUEST' (status=1) Wed Apr 04 21:36:03 2012 PUSH: Received control message: 'PUSH_REPLY,redirect-gateway def1,route 172.16.100.1,topology net30,ping 10,ping-restart 120,ifconfig 172.16.100.6 172.16.100.5' Wed Apr 04 21:36:03 2012 OPTIONS IMPORT: timers and/or timeouts modified Wed Apr 04 21:36:03 2012 OPTIONS IMPORT: --ifconfig/up options modified Wed Apr 04 21:36:03 2012 OPTIONS IMPORT: route options modified Wed Apr 04 21:36:03 2012 ROUTE_GATEWAY 192.168.1.1/255.255.255.0 I=15 HWADDR=00:1f:1f:3f:61:55 Wed Apr 04 21:36:03 2012 do_ifconfig, tt->ipv6=0, tt->did_ifconfig_ipv6_setup=0 Wed Apr 04 21:36:03 2012 MANAGEMENT: >STATE:1333568163,ASSIGN_IP,,172.16.100.6, Wed Apr 04 21:36:03 2012 open_tun, tt->ipv6=0 Wed Apr 04 21:36:03 2012 TAP-WIN32 device [VPN] opened: \\.\Global\{E28FD52B-F6C3-4094-A36A-30CB02FAC7E8}.tap Wed Apr 04 21:36:03 2012 TAP-Win32 Driver Version 9.9 Wed Apr 04 21:36:03 2012 Notified TAP-Win32 driver to set a DHCP IP/netmask of 172.16.100.6/255.255.255.252 on interface {E28FD52B-F6C3-4094-A36A-30CB02FAC7E8} [DHCP-serv: 172.16.100.5, lease-time: 31536000] Wed Apr 04 21:36:03 2012 Successful ARP Flush on interface [31] {E28FD52B-F6C3-4094-A36A-30CB02FAC7E8} Wed Apr 04 21:36:08 2012 TEST ROUTES: 2/2 succeeded len=1 ret=1 a=0 u/d=up Wed Apr 04 21:36:08 2012 C:\Windows\system32\route.exe ADD 11.22.33.44 MASK 255.255.255.255 192.168.1.1 Wed Apr 04 21:36:08 2012 ROUTE: CreateIpForwardEntry succeeded with dwForwardMetric1=25 and dwForwardType=4 Wed Apr 04 21:36:08 2012 Route addition via IPAPI succeeded [adaptive] Wed Apr 04 21:36:08 2012 C:\Windows\system32\route.exe ADD 0.0.0.0 MASK 128.0.0.0 172.16.100.5 Wed Apr 04 21:36:08 2012 ROUTE: CreateIpForwardEntry succeeded with dwForwardMetric1=30 and dwForwardType=4 Wed Apr 04 21:36:08 2012 Route addition via IPAPI succeeded [adaptive] Wed Apr 04 21:36:08 2012 C:\Windows\system32\route.exe ADD 128.0.0.0 MASK 128.0.0.0 172.16.100.5 Wed Apr 04 21:36:08 2012 ROUTE: CreateIpForwardEntry succeeded with dwForwardMetric1=30 and dwForwardType=4 Wed Apr 04 21:36:08 2012 Route addition via IPAPI succeeded [adaptive] Wed Apr 04 21:36:08 2012 MANAGEMENT: >STATE:1333568168,ADD_ROUTES,,, Wed Apr 04 21:36:08 2012 C:\Windows\system32\route.exe ADD 172.16.100.1 MASK 255.255.255.255 172.16.100.5 Wed Apr 04 21:36:08 2012 ROUTE: CreateIpForwardEntry succeeded with dwForwardMetric1=30 and dwForwardType=4 Wed Apr 04 21:36:08 2012 Route addition via IPAPI succeeded [adaptive] Wed Apr 04 21:36:08 2012 Initialization Sequence Completed Wed Apr 04 21:36:08 2012 MANAGEMENT: >STATE:1333568168,CONNECTED,SUCCESS,172.16.100.6,11.22.33.44 Client's route table after connection with OpenVPN: IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.1.1 192.168.1.41 281 0.0.0.0 128.0.0.0 172.16.100.1 172.16.100.6 31 94.23.53.45 255.255.255.255 192.168.1.1 192.168.1.41 25 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 128.0.0.0 128.0.0.0 172.16.100.1 172.16.100.6 31 172.16.100.4 255.255.255.252 On-link 172.16.100.6 286 172.16.100.6 255.255.255.255 On-link 172.16.100.6 286 172.16.100.7 255.255.255.255 On-link 172.16.100.6 286 192.168.1.0 255.255.255.0 On-link 192.168.1.41 281 192.168.1.41 255.255.255.255 On-link 192.168.1.41 281 192.168.1.255 255.255.255.255 On-link 192.168.1.41 281 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 192.168.1.41 281 224.0.0.0 240.0.0.0 On-link 172.16.100.6 286 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 192.168.1.41 281 255.255.255.255 255.255.255.255 On-link 172.16.100.6 286 =========================================================================== Persistent Routes: Network Address Netmask Gateway Address Metric 0.0.0.0 0.0.0.0 192.168.1.1 Default =========================================================================== IPv6 Route Table =========================================================================== Active Routes: If Metric Network Destination Gateway 13 58 ::/0 On-link 1 306 ::1/128 On-link 13 58 2001::/32 On-link 13 306 2001:0:5ef5:79fd:3cc3:6b9:ac7c:14db/128 On-link 15 281 fe80::/64 On-link 31 286 fe80::/64 On-link 13 306 fe80::/64 On-link 13 306 fe80::3cc3:6b9:ac7c:14db/128 On-link 31 286 fe80::7d72:9515:7213:35e3/128 On-link 15 281 fe80::9cec:ce3f:89de:a123/128 On-link 1 306 ff00::/8 On-link 13 306 ff00::/8 On-link 15 281 ff00::/8 On-link 31 286 ff00::/8 On-link =========================================================================== Persistent Routes: None

  Read the article

• Basic shadow mapping fails on NVIDIA card?

  - by James

  Recently I switched from an AMD Radeon HD 6870 card to an (MSI) NVIDIA GTX 670 for performance reasons. I found however that my implementation of shadow mapping in all my applications failed. In a very simple shadow POC project the problem appears to be that the scene being drawn never results in a draw to the depth map and as a result the entire depth map is just infinity, 1.0 (Reading directly from the depth component after draw (glReadPixels) shows every pixel is infinity (1.0), replacing the depth comparison in the shader with a comparison of the depth from the shadow map with 1.0 shadows the entire scene, and writing random values to the depth map and then not calling glClear(GL_DEPTH_BUFFER_BIT) results in a random noisy pattern on the scene elements - from which we can infer that the uploading of the depth texture and comparison within the shader are functioning perfectly.) Since the problem appears almost certainly to be in the depth render, this is the code for that: const int s_res = 1024; GLuint shadowMap_tex; GLuint shadowMap_prog; GLint sm_attr_coord3d; GLint sm_uniform_mvp; GLuint fbo_handle; GLuint renderBuffer; bool isMappingShad = false; //The scene consists of a plane with box above it GLfloat scene[] = { -10.0, 0.0, -10.0, 0.5, 0.0, 10.0, 0.0, -10.0, 1.0, 0.0, 10.0, 0.0, 10.0, 1.0, 0.5, -10.0, 0.0, -10.0, 0.5, 0.0, -10.0, 0.0, 10.0, 0.5, 0.5, 10.0, 0.0, 10.0, 1.0, 0.5, ... }; //Initialize the stuff used by the shadow map generator int initShadowMap() { //Initialize the shadowMap shader program if (create_program("shadow.v.glsl", "shadow.f.glsl", shadowMap_prog) != 1) return -1; const char* attribute_name = "coord3d"; sm_attr_coord3d = glGetAttribLocation(shadowMap_prog, attribute_name); if (sm_attr_coord3d == -1) { fprintf(stderr, "Could not bind attribute %s\n", attribute_name); return 0; } const char* uniform_name = "mvp"; sm_uniform_mvp = glGetUniformLocation(shadowMap_prog, uniform_name); if (sm_uniform_mvp == -1) { fprintf(stderr, "Could not bind uniform %s\n", uniform_name); return 0; } //Create a framebuffer glGenFramebuffers(1, &fbo_handle); glBindFramebuffer(GL_FRAMEBUFFER, fbo_handle); //Create render buffer glGenRenderbuffers(1, &renderBuffer); glBindRenderbuffer(GL_RENDERBUFFER, renderBuffer); //Setup the shadow texture glGenTextures(1, &shadowMap_tex); glBindTexture(GL_TEXTURE_2D, shadowMap_tex); glTexImage2D(GL_TEXTURE_2D, 0, GL_DEPTH_COMPONENT, s_res, s_res, 0, GL_DEPTH_COMPONENT, GL_FLOAT, NULL); glTexParameteri(GL_TEXTURE_2D, GL_TEXTURE_MAG_FILTER, GL_NEAREST); glTexParameteri(GL_TEXTURE_2D, GL_TEXTURE_MIN_FILTER, GL_NEAREST); glTexParameteri(GL_TEXTURE_2D, GL_TEXTURE_WRAP_S, GL_CLAMP_TO_EDGE); glTexParameteri(GL_TEXTURE_2D, GL_TEXTURE_WRAP_T, GL_CLAMP_TO_EDGE); return 0; } //Delete stuff void dnitShadowMap() { //Delete everything glDeleteFramebuffers(1, &fbo_handle); glDeleteRenderbuffers(1, &renderBuffer); glDeleteTextures(1, &shadowMap_tex); glDeleteProgram(shadowMap_prog); } int loadSMap() { //Bind MVP stuff glm::mat4 view = glm::lookAt(glm::vec3(10.0, 10.0, 5.0), glm::vec3(0.0, 0.0, 0.0), glm::vec3(0.0, 1.0, 0.0)); glm::mat4 projection = glm::ortho<float>(-10,10,-8,8,-10,40); glm::mat4 mvp = projection * view; glm::mat4 biasMatrix( 0.5, 0.0, 0.0, 0.0, 0.0, 0.5, 0.0, 0.0, 0.0, 0.0, 0.5, 0.0, 0.5, 0.5, 0.5, 1.0 ); glm::mat4 lsMVP = biasMatrix * mvp; //Upload light source matrix to the main shader programs glUniformMatrix4fv(uniform_ls_mvp, 1, GL_FALSE, glm::value_ptr(lsMVP)); glUseProgram(shadowMap_prog); glUniformMatrix4fv(sm_uniform_mvp, 1, GL_FALSE, glm::value_ptr(mvp)); //Draw to the framebuffer (with depth buffer only draw) glBindFramebuffer(GL_FRAMEBUFFER, fbo_handle); glBindRenderbuffer(GL_RENDERBUFFER, renderBuffer); glBindTexture(GL_TEXTURE_2D, shadowMap_tex); glFramebufferTexture2D(GL_FRAMEBUFFER, GL_DEPTH_ATTACHMENT, GL_TEXTURE_2D, shadowMap_tex, 0); glDrawBuffer(GL_NONE); glReadBuffer(GL_NONE); GLenum result = glCheckFramebufferStatus(GL_FRAMEBUFFER); if (GL_FRAMEBUFFER_COMPLETE != result) { printf("ERROR: Framebuffer is not complete.\n"); return -1; } //Draw shadow scene printf("Creating shadow buffers..\n"); int ticks = SDL_GetTicks(); glClear(GL_DEPTH_BUFFER_BIT); //Wipe the depth buffer glViewport(0, 0, s_res, s_res); isMappingShad = true; //DRAW glEnableVertexAttribArray(sm_attr_coord3d); glVertexAttribPointer(sm_attr_coord3d, 3, GL_FLOAT, GL_FALSE, 5*4, scene); glDrawArrays(GL_TRIANGLES, 0, 14*3); glDisableVertexAttribArray(sm_attr_coord3d); isMappingShad = false; glBindFramebuffer(GL_FRAMEBUFFER, 0); printf("Render Sbuf in %dms (GLerr: %d)\n", SDL_GetTicks() - ticks, glGetError()); return 0; } This is the full code for the POC shadow mapping project (C++) (Requires SDL 1.2, SDL-image 1.2, GLEW (1.5) and GLM development headers.) initShadowMap is called, followed by loadSMap, the scene is drawn from the camera POV and then dnitShadowMap is called. I followed this tutorial originally (Along with another more comprehensive tutorial which has disappeared as this guy re-configured his site but used to be here (404).) I've ensured that the scene is visible (as can be seen within the full project) to the light source (which uses an orthogonal projection matrix.) Shader utilities function fine in non-shadow-mapped projects. I should also note that at no point is the GL error state set. What am I doing wrong here and why did this not cause problems on my AMD card? (System: Ubuntu 12.04, Linux 3.2.0-49-generic, 64 bit, with the nvidia-experimental-310 driver package. All other games are functioning fine so it's most likely not a card/driver issue.)

  Read the article

• SQL Server Transaction Marks: Restoring multiple databases to a common relative point

  - by Mladen Prajdic

  We’re all familiar with the ability to restore a database to point in time using the RESTORE WITH STOPAT statement. But what if we have multiple databases that are accessed from one application or are modifying each other? And over multiple instances? And all databases have different workloads? And we want to restore all of the databases to some known common relative point? The catch here is that this common relative point isn’t the same point in time for all databases. This common relative point in time might be now in DB1, now-1 hour in DB2 and yesterday in DB3. And we don’t know the exact times. Let me introduce you to Transaction Marks. When we run a marked transaction using the WITH MARK option a flag is set in the transaction log and a row is added to msdb..logmarkhistory table. When restoring a transaction log backup we can restore to either before or after that marked transaction. The best thing is that we don’t even need to have one database modifying another database. All we have to do is use a marked transaction with the same name in different database. Let’s see how this works with an example. The code comments say what’s going on. USE master GOCREATE DATABASE TestTxMark1GOUSE TestTxMark1GOCREATE TABLE TestTable1( ID INT, VALUE UNIQUEIDENTIFIER) -- insert some data into the table so we can have a starting pointINSERT INTO TestTable1SELECT ROW_NUMBER() OVER(ORDER BY number) AS RN, NULLFROM master..spt_valuesORDER BY RNSELECT *FROM TestTable1GO-- TAKE A FULL BACKUP of the databseBACKUP DATABASE TestTxMark1 TO DISK = 'c:\TestTxMark1.bak'GO USE master GOCREATE DATABASE TestTxMark2GOUSE TestTxMark2GOCREATE TABLE TestTable2( ID INT, VALUE UNIQUEIDENTIFIER)-- insert some data into the table so we can have a starting pointINSERT INTO TestTable2SELECT ROW_NUMBER() OVER(ORDER BY number) AS RN, NEWID()FROM master..spt_valuesORDER BY RNSELECT *FROM TestTable2GO-- TAKE A FULL BACKUP of our databseBACKUP DATABASE TestTxMark2 TO DISK = 'c:\TestTxMark2.bak'GO -- start a marked transaction that modifies both databasesBEGIN TRAN TxDb WITH MARK -- update values from NULL to random value UPDATE TestTable1 SET VALUE = NEWID(); -- update first 100 values from random value -- to NULL in different DB UPDATE TestTxMark2.dbo.TestTable2 SET VALUE = NULL WHERE ID <= 100;COMMITGO     -- some time goes by here -- with various database activity... -- We see two entries for marks in each database. -- This is just informational and has no bearing on the restore itself.SELECT * FROM msdb..logmarkhistory USE masterGO-- create a log backup to restore to mark pointBACKUP LOG TestTxMark1 TO DISK = 'c:\TestTxMark1.trn'GO-- drop the database so we can restore it backDROP DATABASE TestTxMark1GO USE masterGO-- create a log backup to restore to mark pointBACKUP LOG TestTxMark2 TO DISK = 'c:\TestTxMark2.trn'GO-- drop the database so we can restore it backDROP DATABASE TestTxMark2GO -- RESTORE THE DATABASE BACK BEFORE OUR TRANSACTION-- restore the full backup RESTORE DATABASE TestTxMark1 FROM DISK = 'c:\TestTxMark1.bak' WITH NORECOVERY;-- restore the log backup to the transaction markRESTORE LOG TestTxMark1 FROM DISK = 'c:\TestTxMark1.trn' WITH RECOVERY, -- recover to state before the transaction STOPBEFOREMARK = 'TxDb'; -- recover to state after the transaction -- STOPATMARK = 'TxDb';GO -- RESTORE THE DATABASE BACK BEFORE OUR TRANSACTION-- restore the full backup RESTORE DATABASE TestTxMark2 FROM DISK = 'c:\TestTxMark2.bak' WITH NORECOVERY;-- restore the log backup to the transaction markRESTORE LOG TestTxMark2 FROM DISK = 'c:\TestTxMark2.trn' WITH RECOVERY, -- recover to state before the transaction STOPBEFOREMARK = 'TxDb'; -- recover to state after the transaction -- STOPATMARK = 'TxDb';GO USE TestTxMark1-- we restored to time before the transaction -- so we have NULL values in our tableSELECT * FROM TestTable1 USE TestTxMark2-- we restored to time before the transaction -- so we DON'T have NULL values in our tableSELECT * FROM TestTable2   Transaction marks can be used like a crude sync mechanism for cross database operations. With them we can mark our databases with a common “restore to” point so we know we have a valid state between all databases to restore to.

  Read the article

• Trying to implement fling events on an object

  - by Adam Short

  I have a game object, well a bitmap, which I'd like to "fling". I'm struggling to get it to fling ontouchlistener due to it being a bitmap and not sure how to proceed and I'm struggling to find the resources to help. Here's my code so far: https://github.com/addrum/Shapes GameActivity class: package com.main.shapes; import android.app.Activity; import android.content.Context; import android.graphics.Bitmap; import android.graphics.BitmapFactory; import android.graphics.Canvas; import android.os.Bundle; import android.view.GestureDetector; import android.view.MotionEvent; import android.view.SurfaceHolder; import android.view.SurfaceView; import android.view.View.OnTouchListener; import android.view.Window; public class GameActivity extends Activity { private GestureDetector gestureDetector; View view; Bitmap ball; float x, y; @Override protected void onCreate(Bundle savedInstanceState) { super.onCreate(savedInstanceState); //Remove title bar this.requestWindowFeature(Window.FEATURE_NO_TITLE); view = new View(this); ball = BitmapFactory.decodeResource(getResources(), R.drawable.ball); gestureDetector = new GestureDetector(this, new GestureListener()); x = 0; y = 0; setContentView(view); ball.setOnTouchListener(new OnTouchListener() { @Override public boolean onTouch(android.view.View v, MotionEvent event) { // TODO Auto-generated method stub return false; } }); } @Override protected void onPause() { super.onPause(); view.pause(); } @Override protected void onResume() { super.onResume(); view.resume(); } public class View extends SurfaceView implements Runnable { Thread thread = null; SurfaceHolder holder; boolean canRun = false; public View(Context context) { super(context); holder = getHolder(); } public void run() { while (canRun) { if (!holder.getSurface().isValid()) { continue; } Canvas c = holder.lockCanvas(); c.drawARGB(255, 255, 255, 255); c.drawBitmap(ball, x - (ball.getWidth() / 2), y - (ball.getHeight() / 2), null); holder.unlockCanvasAndPost(c); } } public void pause() { canRun = false; while (true) { try { thread.join(); } catch (InterruptedException e) { e.printStackTrace(); } break; } thread = null; } public void resume() { canRun = true; thread = new Thread(this); thread.start(); } } } GestureListener class: package com.main.shapes; import android.view.GestureDetector.SimpleOnGestureListener; import android.view.MotionEvent; public class GestureListener extends SimpleOnGestureListener { private static final int SWIPE_MIN_DISTANCE = 120; private static final int SWIPE_THRESHOLD_VELOCITY = 200; @Override public boolean onFling(MotionEvent e1, MotionEvent e2, float velocityX, float velocityY) { if (e1.getX() - e2.getX() > SWIPE_MIN_DISTANCE && Math.abs(velocityX) > SWIPE_THRESHOLD_VELOCITY) { //From Right to Left return true; } else if (e2.getX() - e1.getX() > SWIPE_MIN_DISTANCE && Math.abs(velocityX) > SWIPE_THRESHOLD_VELOCITY) { //From Left to Right return true; } if (e1.getY() - e2.getY() > SWIPE_MIN_DISTANCE && Math.abs(velocityY) > SWIPE_THRESHOLD_VELOCITY) { //From Bottom to Top return true; } else if (e2.getY() - e1.getY() > SWIPE_MIN_DISTANCE && Math.abs(velocityY) > SWIPE_THRESHOLD_VELOCITY) { //From Top to Bottom return true; } return false; } @Override public boolean onDown(MotionEvent e) { //always return true since all gestures always begin with onDown and<br> //if this returns false, the framework won't try to pick up onFling for example. return true; } }

  Read the article

• XNA RTS A* pathfinding issues

  - by Slayter

  I'm starting to develop an RTS game using the XNA framework in C# and am still in the very early prototyping stage. I'm working on the basics. I've got unit selection down and am currently working on moving multiple units. I've implemented an A* pathfinding algorithm which works fine for moving a single unit. However when moving multiple units they stack on top of each other. I tried fixing this with a variation of the boids flocking algorithm but this has caused units to sometimes freeze and get stuck trying to move but going no where. Ill post the related methods for moving the units below but ill only post a link to the pathfinding class because its really long and i don't want to clutter up the page. These parts of the code are in the update method for the main controlling class: if (selectedUnits.Count > 0) { int indexOfLeader = 0; for (int i = 0; i < selectedUnits.Count; i++) { if (i == 0) { indexOfLeader = 0; } else { if (Vector2.Distance(selectedUnits[i].position, destination) < Vector2.Distance(selectedUnits[indexOfLeader].position, destination)) indexOfLeader = i; } selectedUnits[i].leader = false; } selectedUnits[indexOfLeader].leader = true; foreach (Unit unit in selectedUnits) unit.FindPath(destination); } foreach (Unit unit in units) { unit.Update(gameTime, selectedUnits); } These three methods control movement in the Unit class: public void FindPath(Vector2 destination) { if (path != null) path.Clear(); Point startPoint = new Point((int)position.X / 32, (int)position.Y / 32); Point endPoint = new Point((int)destination.X / 32, (int)destination.Y / 32); path = pathfinder.FindPath(startPoint, endPoint); pointCounter = 0; if (path != null) nextPoint = path[pointCounter]; dX = 0.0f; dY = 0.0f; stop = false; } private void Move(List<Unit> units) { if (nextPoint == position && !stop) { pointCounter++; if (pointCounter <= path.Count - 1) { nextPoint = path[pointCounter]; if (nextPoint == position) stop = true; } else if (pointCounter >= path.Count) { path.Clear(); pointCounter = 0; stop = true; } } else { if (!stop) { map.occupiedPoints.Remove(this); Flock(units); // Move in X ********* TOOK OUT SPEED ********** if ((int)nextPoint.X > (int)position.X) { position.X += dX; } else if ((int)nextPoint.X < (int)position.X) { position.X -= dX; } // Move in Y if ((int)nextPoint.Y > (int)position.Y) { position.Y += dY; } else if ((int)nextPoint.Y < (int)position.Y) { position.Y -= dY; } if (position == nextPoint && pointCounter >= path.Count - 1) stop = true; map.occupiedPoints.Add(this, position); } if (stop) { path.Clear(); pointCounter = 0; } } } private void Flock(List<Unit> units) { float distanceToNextPoint = Vector2.Distance(position, nextPoint); foreach (Unit unit in units) { float distance = Vector2.Distance(position, unit.position); if (unit != this) { if (distance < space && !leader && (nextPoint != position)) { // create space dX += (position.X - unit.position.X) * 0.1f; dY += (position.Y - unit.position.Y) * 0.1f; if (dX > .05f) nextPoint.X = nextPoint.X - dX; else if (dX < -.05f) nextPoint.X = nextPoint.X + dX; if (dY > .05f) nextPoint.Y = nextPoint.Y - dY; else if (dY < -.05f) nextPoint.Y = nextPoint.Y + dY; if ((dX < .05f && dX > -.05f) && (dY < .05f && dY > -.05f)) stop = true; path[pointCounter] = nextPoint; Console.WriteLine("Make Space: " + dX + ", " + dY); } else if (nextPoint != position && !stop) { dX = speed; dY = speed; Console.WriteLine(dX + ", " + dY); } } } } And here's the link to the pathfinder: https://docs.google.com/open?id=0B_Cqt6txUDkddU40QXBMeTR1djA I hope this post wasn't too long. Also please excuse the messiness of the code. As I said before this is early prototyping. Any help would be appreciated. Thanks!

  Read the article

• Trying to detect collision between two polygons using Separating Axis Theorem

  - by Holly

  The only collision experience i've had was with simple rectangles, i wanted to find something that would allow me to define polygonal areas for collision and have been trying to make sense of SAT using these two links Though i'm a bit iffy with the math for the most part i feel like i understand the theory! Except my implementation somewhere down the line must be off as: (excuse the hideous font) As mentioned above i have defined a CollisionPolygon class where most of my theory is implemented and then have a helper class called Vect which was meant to be for Vectors but has also been used to contain a vertex given that both just have two float values. I've tried stepping through the function and inspecting the values to solve things but given so many axes and vectors and new math to work out as i go i'm struggling to find the erroneous calculation(s) and would really appreciate any help. Apologies if this is not suitable as a question! CollisionPolygon.java: package biz.hireholly.gameplay; import android.graphics.Canvas; import android.graphics.Color; import android.graphics.Paint; import biz.hireholly.gameplay.Types.Vect; public class CollisionPolygon { Paint paint; private Vect[] vertices; private Vect[] separationAxes; CollisionPolygon(Vect[] vertices){ this.vertices = vertices; //compute edges and separations axes separationAxes = new Vect[vertices.length]; for (int i = 0; i < vertices.length; i++) { // get the current vertex Vect p1 = vertices[i]; // get the next vertex Vect p2 = vertices[i + 1 == vertices.length ? 0 : i + 1]; // subtract the two to get the edge vector Vect edge = p1.subtract(p2); // get either perpendicular vector Vect normal = edge.perp(); // the perp method is just (x, y) => (-y, x) or (y, -x) separationAxes[i] = normal; } paint = new Paint(); paint.setColor(Color.RED); } public void draw(Canvas c, int xPos, int yPos){ for (int i = 0; i < vertices.length; i++) { Vect v1 = vertices[i]; Vect v2 = vertices[i + 1 == vertices.length ? 0 : i + 1]; c.drawLine( xPos + v1.x, yPos + v1.y, xPos + v2.x, yPos + v2.y, paint); } } /* consider changing to a static function */ public boolean intersects(CollisionPolygon p){ // loop over this polygons separation exes for (Vect axis : separationAxes) { // project both shapes onto the axis Vect p1 = this.minMaxProjection(axis); Vect p2 = p.minMaxProjection(axis); // do the projections overlap? if (!p1.overlap(p2)) { // then we can guarantee that the shapes do not overlap return false; } } // loop over the other polygons separation axes Vect[] sepAxesOther = p.getSeparationAxes(); for (Vect axis : sepAxesOther) { // project both shapes onto the axis Vect p1 = this.minMaxProjection(axis); Vect p2 = p.minMaxProjection(axis); // do the projections overlap? if (!p1.overlap(p2)) { // then we can guarantee that the shapes do not overlap return false; } } // if we get here then we know that every axis had overlap on it // so we can guarantee an intersection return true; } /* Note projections wont actually be acurate if the axes aren't normalised * but that's not necessary since we just need a boolean return from our * intersects not a Minimum Translation Vector. */ private Vect minMaxProjection(Vect axis) { float min = axis.dot(vertices[0]); float max = min; for (int i = 1; i < vertices.length; i++) { float p = axis.dot(vertices[i]); if (p < min) { min = p; } else if (p > max) { max = p; } } Vect minMaxProj = new Vect(min, max); return minMaxProj; } public Vect[] getSeparationAxes() { return separationAxes; } public Vect[] getVertices() { return vertices; } } Vect.java: package biz.hireholly.gameplay.Types; /* NOTE: Can also be used to hold vertices! Projections, coordinates ect */ public class Vect{ public float x; public float y; public Vect(float x, float y){ this.x = x; this.y = y; } public Vect perp() { return new Vect(-y, x); } public Vect subtract(Vect other) { return new Vect(x - other.x, y - other.y); } public boolean overlap(Vect other) { if( other.x <= y || other.y >= x){ return true; } return false; } /* used specifically for my SAT implementation which i'm figuring out as i go, * references for later.. * http://www.gamedev.net/page/resources/_/technical/game-programming/2d-rotated-rectangle-collision-r2604 * http://www.codezealot.org/archives/55 */ public float scalarDotProjection(Vect other) { //multiplier = dot product / length^2 float multiplier = dot(other) / (x*x + y*y); //to get the x/y of the projection vector multiply by x/y of axis float projX = multiplier * x; float projY = multiplier * y; //we want to return the dot product of the projection, it's meaningless but useful in our SAT case return dot(new Vect(projX,projY)); } public float dot(Vect other){ return (other.x*x + other.y*y); } }

  Read the article

• Libnoise producing completely random noise

  - by Doodlemeat

  I am using libnoise in C++ taken and I have some problems with getting coherent noise. I mean, the noise produced now are completely random and it doesn't look like a noise. Here's a to the image produced by my game. I am diving the map into several chunks, but I can't seem to find any problem doing that since libnoise supports tileable noise. The code can be found below. Every chunk is 8x8 tiles large. Every tile is 64x64 pixels. I am also providing a link to download the entire project. It was made in Visual Studio 2013. Download link This is the code for generating a chunk Chunk *World::loadChunk(sf::Vector2i pPosition) { sf::Vector2i chunkPos = pPosition; pPosition.x *= mChunkTileSize.x; pPosition.y *= mChunkTileSize.y; sf::FloatRect bounds(static_cast<sf::Vector2f>(pPosition), sf::Vector2f(static_cast<float>(mChunkTileSize.x), static_cast<float>(mChunkTileSize.y))); utils::NoiseMap heightMap; utils::NoiseMapBuilderPlane heightMapBuilder; heightMapBuilder.SetSourceModule(mNoiseModule); heightMapBuilder.SetDestNoiseMap(heightMap); heightMapBuilder.SetDestSize(mChunkTileSize.x, mChunkTileSize.y); heightMapBuilder.SetBounds(bounds.left, bounds.left + bounds.width - 1, bounds.top, bounds.top + bounds.height - 1); heightMapBuilder.Build(); Chunk *chunk = new Chunk(this); chunk->setPosition(chunkPos); chunk->buildChunk(&heightMap); chunk->setTexture(&mTileset); mChunks.push_back(chunk); return chunk; } This is the code for building the chunk void Chunk::buildChunk(utils::NoiseMap *pHeightMap) { // Resize the tiles space mTiles.resize(pHeightMap->GetWidth()); for (int x = 0; x < mTiles.size(); x++) { mTiles[x].resize(pHeightMap->GetHeight()); } // Set vertices type and size mVertices.setPrimitiveType(sf::Quads); mVertices.resize(pHeightMap->GetWidth() * pHeightMap->GetWidth() * 4); // Get the offset position of all tiles position sf::Vector2i tileSize = mWorld->getTileSize(); sf::Vector2i chunkSize = mWorld->getChunkSize(); sf::Vector2f offsetPositon = sf::Vector2f(mPosition); offsetPositon.x *= chunkSize.x; offsetPositon.y *= chunkSize.y; // Build tiles for (int x = 0; x < mTiles.size(); x++) { for (int y = 0; y < mTiles[x].size(); y++) { // Sometimes libnoise can return a value over 1.0, better be sure to cap the top and bottom.. float heightValue = pHeightMap->GetValue(x, y); if (heightValue > 1.f) heightValue = 1.f; if (heightValue < -1.f) heightValue = -1.f; // Instantiate a new Tile object with the noise value, this doesn't do anything yet.. mTiles[x][y] = new Tile(this, pHeightMap->GetValue(x, y)); // Get a pointer to the current tile's quad sf::Vertex *quad = &mVertices[(y + x * pHeightMap->GetWidth()) * 4]; quad[0].position = sf::Vector2f(offsetPositon.x + x * tileSize.x, offsetPositon.y + y * tileSize.y); quad[1].position = sf::Vector2f(offsetPositon.x + (x + 1) * tileSize.x, offsetPositon.y + y * tileSize.y); quad[2].position = sf::Vector2f(offsetPositon.x + (x + 1) * tileSize.x, offsetPositon.y + (y + 1) * tileSize.y); quad[3].position = sf::Vector2f(offsetPositon.x + x * tileSize.x, offsetPositon.y + (y + 1) * tileSize.y); // find out which type of tile to render, atm only air or stone TileStop *tilestop = mWorld->getTileStopAt(heightValue); sf::Vector2i texturePos = tilestop->getTexturePosition(); // define its 4 texture coordinates quad[0].texCoords = sf::Vector2f(texturePos.x, texturePos.y); quad[1].texCoords = sf::Vector2f(texturePos.x + 64, texturePos.y); quad[2].texCoords = sf::Vector2f(texturePos.x + 64, texturePos.y + 64); quad[3].texCoords = sf::Vector2f(texturePos.x, texturePos.y + 64); } } } All the code that uses libnoise in some way are World.cpp, World.h and Chunk.cpp, Chunk.h in the project.

  Read the article

• XNA: Huge Tile Map, long load times

  - by Zach

  Recently I built a tile map generator for a game project. What I am very proud of is that I finally got it to the point where I can have a GIANT 2D map build perfectly on my PC. About 120000pixels by 40000 pixels. I can go larger actually, but I have only 1 draw back. #1 ram, the map currently draws about 320MB of ram and I know the Xbox allows 512MB I think? #2 It takes 20 mins for the map to build then display on the Xbox, on my PC it take less then a few seconds. I need to bring that 20 minutes of generating from 20 mins to how ever little bit I can, and how can a lower the amount of RAM usage while still being able to generate my map. Right now everything is stored in Jagged Arrays, each piece generating in a size of 1280x720 (the mother piece). Up to the amount that I need, every block is exactly 40x40 pixels however the blocks get removed from a List or regenerated in a List depending how close the mother piece is to the player. Saving A LOT of CPU, so at all times its no more then looping through 5184 some blocks. Well at least I'm sure of this. But how can I lower my RAM usage without hurting the size of the map, and how can I lower these INSANE loading times? EDIT: Let me explain my self better. Also I'd like to let everyone know now that I'm inexperienced with many of these things. So here is an example of the arrays I'm using. Here is the overall in a shorter term: int[][] array = new int[30][]; array[0] = new int[] { 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2 }; array[1] = new int[] { 1, 3, 3, 3, 3, 1, 0, 0, 0, 0, 1, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2 }; that goes on for around 30 arrays downward. Now for every time it hits a 1, it goes and generates a tile map 1280x720 and it does that exactly the way it does it above. This is how I loop through those arrays: for (int i = 0; i < array.Length; i += 1) { for (int h = 0; h < array[i].Length; h += 1) { } { Now how the tiles are drawn and removed is something like this: public void Draw(SpriteBatch spriteBatch, Vector2 cam) { if (cam.X >= this.Position.X - 1280) { if (cam.X <= this.Position.X + 2560) { if (cam.Y >= this.Position.Y - 720) { if (cam.Y <= this.Position.Y + 1440) { if (visible) { if (once == 0) { once = 1; visible = false; regen(); } } for (int i = Tiles.Count - 1; i >= 0; i--) { Tiles[i].Draw(spriteBatch, cam); } for (int i = unWalkTiles.Count - 1; i >= 0; i--) { unWalkTiles[i].Draw(spriteBatch, cam); } } else { once = 0; for (int i = Tiles.Count - 1; i >= 0; i--) { Tiles.RemoveAt(i); } for (int i = unWalkTiles.Count - 1; i >= 0; i--) { unWalkTiles.RemoveAt(i); } } } else { once = 0; for (int i = Tiles.Count - 1; i >= 0; i--) { Tiles.RemoveAt(i); } for (int i = unWalkTiles.Count - 1; i >= 0; i--) { unWalkTiles.RemoveAt(i); } } } else { once = 0; for (int i = Tiles.Count - 1; i >= 0; i--) { Tiles.RemoveAt(i); } for (int i = unWalkTiles.Count - 1; i >= 0; i--) { unWalkTiles.RemoveAt(i); } } } else { once = 0; for (int i = Tiles.Count - 1; i >= 0; i--) { Tiles.RemoveAt(i); } for (int i = unWalkTiles.Count - 1; i >= 0; i--) { unWalkTiles.RemoveAt(i); } } } } If you guys still need more information just ask in the comments.

  Read the article

• How to properly add texture to multi-fixture/shape b2Body

  - by Blazej Wdowikowski

  Hello to everyone this is my first poste here I hope that will be not fail start. At start I must say I make part 1 in Ray's Tutorial "How To Make A Game Like Fruit Ninja With Box2D and Cocos2D". But I wonder what when I want make more complex body with texture? Simple just add n b2FixtureDef to the same body. OK but what about texture? If I will take code from that tutorial it only fill last fixture. Probably it does not takes every b2Vec2 point. I was right, it did not. So quick refactor and from that -(id)initWithTexture:(CCTexture2D*)texture body:(b2Body*)body original:(BOOL)original { // gather all the vertices from our Box2D shape b2Fixture *originalFixture = body->GetFixtureList(); b2PolygonShape *shape = (b2PolygonShape*)originalFixture->GetShape(); int vertexCount = shape->GetVertexCount(); NSMutableArray *points = [NSMutableArray arrayWithCapacity:vertexCount]; for(int i = 0; i < vertexCount; i++) { CGPoint p = ccp(shape->GetVertex(i).x * PTM_RATIO, shape->GetVertex(i).y * PTM_RATIO); [points addObject:[NSValue valueWithCGPoint:p]]; } if ((self = [super initWithPoints:points andTexture:texture])) { _body = body; _body->SetUserData(self); _original = original; // gets the center of the polygon _centroid = self.body->GetLocalCenter(); // assign an anchor point based on the center self.anchorPoint = ccp(_centroid.x * PTM_RATIO / texture.contentSize.width, _centroid.y * PTM_RATIO / texture.contentSize.height); } return self; } I came up with that -(id)initWithTexture:(CCTexture2D*)texture body:(b2Body*)body original:(BOOL)original { int vertexCount = 0; //gather total number of b2Vect2 points b2Fixture *currentFixture = body->GetFixtureList(); while (currentFixture) { //new b2PolygonShape *shape = (b2PolygonShape*)currentFixture->GetShape(); vertexCount += shape->GetVertexCount(); currentFixture = currentFixture->GetNext(); } NSMutableArray *points = [NSMutableArray arrayWithCapacity:vertexCount]; // gather all the vertices from our Box2D shape b2Fixture *originalFixture = body->GetFixtureList(); while (originalFixture) { //new NSLog((NSString*)@"-"); b2PolygonShape *shape = (b2PolygonShape*)originalFixture->GetShape(); int currentVertexCount = shape->GetVertexCount(); for(int i = 0; i < currentVertexCount; i++) { CGPoint p = ccp(shape->GetVertex(i).x * PTM_RATIO, shape->GetVertex(i).y * PTM_RATIO); [points addObject:[NSValue valueWithCGPoint:p]]; } originalFixture = originalFixture->GetNext(); } if ((self = [super initWithPoints:points andTexture:texture])) { _body = body; _body->SetUserData(self); _original = original; // gets the center of the polygon _centroid = self.body->GetLocalCenter(); // assign an anchor point based on the center self.anchorPoint = ccp(_centroid.x * PTM_RATIO / texture.contentSize.width,_centroid.y * PTM_RATIO / texture.contentSize.height); } return self; } I was working for simple two fixtures body like b2BodyDef bodyDef; bodyDef.type = b2_dynamicBody; bodyDef.position = position; bodyDef.angle = rotation; b2Body *body = world->CreateBody(&bodyDef); b2FixtureDef fixtureDef; fixtureDef.density = 1.0; fixtureDef.friction = 0.5; fixtureDef.restitution = 0.2; fixtureDef.filter.categoryBits = 0x0001; fixtureDef.filter.maskBits = 0x0001; b2Vec2 vertices[] = { b2Vec2(0.0/PTM_RATIO,50.0/PTM_RATIO), b2Vec2(0.0/PTM_RATIO,0.0/PTM_RATIO), b2Vec2(50.0/PTM_RATIO,30.1/PTM_RATIO), b2Vec2(60.0/PTM_RATIO,60.0/PTM_RATIO) }; b2PolygonShape shape; shape.Set(vertices, 4); fixtureDef.shape = &shape; body->CreateFixture(&fixtureDef); b2Vec2 vertices2[] = { b2Vec2(20.0/PTM_RATIO,50.0/PTM_RATIO), b2Vec2(20.0/PTM_RATIO,0.0/PTM_RATIO), b2Vec2(70.0/PTM_RATIO,30.1/PTM_RATIO), b2Vec2(80.0/PTM_RATIO,60.0/PTM_RATIO) }; shape.Set(vertices2, 4); fixtureDef.shape = &shape; body->CreateFixture(&fixtureDef); But if I try put secondary shape upper than first it starting wierd, texture goes crazy. For example not mention about more complex shapes. What's more if shapes have one common point texture will not render for them at all [For that I use Physics Edytor like in tutorial part1] BTW. I use PolygonSprite and in method createWithWorld... another shapes. Uff.. Question So my question is, why texture coords are in such a mess up? It's my modify method or just wrong approach? Maybe I should remove duplicated from points array?

  Read the article

• SQL Server IO handling mechanism can be severely affected by high CPU usage

  - by sqlworkshops

  Are you using SSD or SAN / NAS based storage solution and sporadically observe SQL Server experiencing high IO wait times or from time to time your DAS / HDD becomes very slow according to SQL Server statistics? Read on… I need your help to up vote my connect item – https://connect.microsoft.com/SQLServer/feedback/details/744650/sql-server-io-handling-mechanism-can-be-severely-affected-by-high-cpu-usage. Instead of taking few seconds, queries could take minutes/hours to complete when CPU is busy.In SQL Server when a query / request needs to read data that is not in data cache or when the request has to write to disk, like transaction log records, the request / task will queue up the IO operation and wait for it to complete (task in suspended state, this wait time is the resource wait time). When the IO operation is complete, the task will be queued to run on the CPU. If the CPU is busy executing other tasks, this task will wait (task in runnable state) until other tasks in the queue either complete or get suspended due to waits or exhaust their quantum of 4ms (this is the signal wait time, which along with resource wait time will increase the overall wait time). When the CPU becomes free, the task will finally be run on the CPU (task in running state).The signal wait time can be up to 4ms per runnable task, this is by design. So if a CPU has 5 runnable tasks in the queue, then this query after the resource becomes available might wait up to a maximum of 5 X 4ms = 20ms in the runnable state (normally less as other tasks might not use the full quantum).In case the CPU usage is high, let’s say many CPU intensive queries are running on the instance, there is a possibility that the IO operations that are completed at the Hardware and Operating System level are not yet processed by SQL Server, keeping the task in the resource wait state for longer than necessary. In case of an SSD, the IO operation might even complete in less than a millisecond, but it might take SQL Server 100s of milliseconds, for instance, to process the completed IO operation. For example, let’s say you have a user inserting 500 rows in individual transactions. When the transaction log is on an SSD or battery backed up controller that has write cache enabled, all of these inserts will complete in 100 to 200ms. With a CPU intensive parallel query executing across all CPU cores, the same inserts might take minutes to complete. WRITELOG wait time will be very high in this case (both under sys.dm_io_virtual_file_stats and sys.dm_os_wait_stats). In addition you will notice a large number of WAITELOG waits since log records are written by LOG WRITER and hence very high signal_wait_time_ms leading to more query delays. However, Performance Monitor Counter, PhysicalDisk, Avg. Disk sec/Write will report very low latency times.Such delayed IO handling also occurs to read operations with artificially very high PAGEIOLATCH_SH wait time (with number of PAGEIOLATCH_SH waits remaining the same). This problem will manifest more and more as customers start using SSD based storage for SQL Server, since they drive the CPU usage to the limits with faster IOs. We have a few workarounds for specific scenarios, but we think Microsoft should resolve this issue at the product level. We have a connect item open – https://connect.microsoft.com/SQLServer/feedback/details/744650/sql-server-io-handling-mechanism-can-be-severely-affected-by-high-cpu-usage - (with example scripts) to reproduce this behavior, please up vote the item so the issue will be addressed by the SQL Server product team soon.Thanks for your help and best regards,Ramesh MeyyappanHome: www.sqlworkshops.comLinkedIn: http://at.linkedin.com/in/rmeyyappan

  Read the article

• Error in my Separating Axis Theorem collision code

  - by Holly

  The only collision experience i've had was with simple rectangles, i wanted to find something that would allow me to define polygonal areas for collision and have been trying to make sense of SAT using these two links Though i'm a bit iffy with the math for the most part i feel like i understand the theory! Except my implementation somewhere down the line must be off as: (excuse the hideous font) As mentioned above i have defined a CollisionPolygon class where most of my theory is implemented and then have a helper class called Vect which was meant to be for Vectors but has also been used to contain a vertex given that both just have two float values. I've tried stepping through the function and inspecting the values to solve things but given so many axes and vectors and new math to work out as i go i'm struggling to find the erroneous calculation(s) and would really appreciate any help. Apologies if this is not suitable as a question! CollisionPolygon.java: package biz.hireholly.gameplay; import android.graphics.Canvas; import android.graphics.Color; import android.graphics.Paint; import biz.hireholly.gameplay.Types.Vect; public class CollisionPolygon { Paint paint; private Vect[] vertices; private Vect[] separationAxes; int x; int y; CollisionPolygon(Vect[] vertices){ this.vertices = vertices; //compute edges and separations axes separationAxes = new Vect[vertices.length]; for (int i = 0; i < vertices.length; i++) { // get the current vertex Vect p1 = vertices[i]; // get the next vertex Vect p2 = vertices[i + 1 == vertices.length ? 0 : i + 1]; // subtract the two to get the edge vector Vect edge = p1.subtract(p2); // get either perpendicular vector Vect normal = edge.perp(); // the perp method is just (x, y) => (-y, x) or (y, -x) separationAxes[i] = normal; } paint = new Paint(); paint.setColor(Color.RED); } public void draw(Canvas c, int xPos, int yPos){ for (int i = 0; i < vertices.length; i++) { Vect v1 = vertices[i]; Vect v2 = vertices[i + 1 == vertices.length ? 0 : i + 1]; c.drawLine( xPos + v1.x, yPos + v1.y, xPos + v2.x, yPos + v2.y, paint); } } public void update(int xPos, int yPos){ x = xPos; y = yPos; } /* consider changing to a static function */ public boolean intersects(CollisionPolygon p){ // loop over this polygons separation exes for (Vect axis : separationAxes) { // project both shapes onto the axis Vect p1 = this.minMaxProjection(axis); Vect p2 = p.minMaxProjection(axis); // do the projections overlap? if (!p1.overlap(p2)) { // then we can guarantee that the shapes do not overlap return false; } } // loop over the other polygons separation axes Vect[] sepAxesOther = p.getSeparationAxes(); for (Vect axis : sepAxesOther) { // project both shapes onto the axis Vect p1 = this.minMaxProjection(axis); Vect p2 = p.minMaxProjection(axis); // do the projections overlap? if (!p1.overlap(p2)) { // then we can guarantee that the shapes do not overlap return false; } } // if we get here then we know that every axis had overlap on it // so we can guarantee an intersection return true; } /* Note projections wont actually be acurate if the axes aren't normalised * but that's not necessary since we just need a boolean return from our * intersects not a Minimum Translation Vector. */ private Vect minMaxProjection(Vect axis) { float min = axis.dot(new Vect(vertices[0].x+x, vertices[0].y+y)); float max = min; for (int i = 1; i < vertices.length; i++) { float p = axis.dot(new Vect(vertices[i].x+x, vertices[i].y+y)); if (p < min) { min = p; } else if (p > max) { max = p; } } Vect minMaxProj = new Vect(min, max); return minMaxProj; } public Vect[] getSeparationAxes() { return separationAxes; } public Vect[] getVertices() { return vertices; } } Vect.java: package biz.hireholly.gameplay.Types; /* NOTE: Can also be used to hold vertices! Projections, coordinates ect */ public class Vect{ public float x; public float y; public Vect(float x, float y){ this.x = x; this.y = y; } public Vect perp() { return new Vect(-y, x); } public Vect subtract(Vect other) { return new Vect(x - other.x, y - other.y); } public boolean overlap(Vect other) { if(y > other.x && other.y > x){ return true; } return false; } /* used specifically for my SAT implementation which i'm figuring out as i go, * references for later.. * http://www.gamedev.net/page/resources/_/technical/game-programming/2d-rotated-rectangle-collision-r2604 * http://www.codezealot.org/archives/55 */ public float scalarDotProjection(Vect other) { //multiplier = dot product / length^2 float multiplier = dot(other) / (x*x + y*y); //to get the x/y of the projection vector multiply by x/y of axis float projX = multiplier * x; float projY = multiplier * y; //we want to return the dot product of the projection, it's meaningless but useful in our SAT case return dot(new Vect(projX,projY)); } public float dot(Vect other){ return (other.x*x + other.y*y); } }

  Read the article

• Collision Error

  - by Manji

  I am having trouble with collision detection part of the game. I am using touch events to fire the gun as you will see in the video. Note, the android icon is a temporary graphic for the bullets When ever the user touches (represented by clicks in the video)the bullet appears and kills random sprites. As you can see it never touches the sprites it kills or kill the sprites it does touch. My Question is How do I fix it, so that the sprite dies when the bullet hits it? Collision Code snippet: //Handles Collision private void CheckCollisions(){ synchronized(mSurfaceHolder){ for (int i = sprites.size() - 1; i >= 0; i--){ Sprite sprite = sprites.get(i); if(sprite.isCollision(bullet)){ sprites.remove(sprite); mScore++; if(sprites.size() == 0){ mLevel = mLevel +1; currentLevel++; initLevel(); } break; } } } } Sprite Class Code Snippet: //bounding box left<right and top>bottom int left ; int right ; int top ; int bottom ; public boolean isCollision(Beam other) { // TODO Auto-generated method stub if(this.left>other.right || other.left<other.right)return false; if(this.bottom>other.top || other.bottom<other.top)return false; return true; } EDIT 1: Sprite Class: public class Sprite { // direction = 0 up, 1 left, 2 down, 3 right, // animation = 3 back, 1 left, 0 front, 2 right int[] DIRECTION_TO_ANIMATION_MAP = { 3, 1, 0, 2 }; private static final int BMP_ROWS = 4; private static final int BMP_COLUMNS = 3; private static final int MAX_SPEED = 5; private HitmanView gameView; private Bitmap bmp; private int x; private int y; private int xSpeed; private int ySpeed; private int currentFrame = 0; private int width; private int height; //bounding box left<right and top>bottom int left ; int right ; int top ; int bottom ; public Sprite(HitmanView gameView, Bitmap bmp) { this.width = bmp.getWidth() / BMP_COLUMNS; this.height = bmp.getHeight() / BMP_ROWS; this.gameView = gameView; this.bmp = bmp; Random rnd = new Random(); x = rnd.nextInt(gameView.getWidth() - width); y = rnd.nextInt(gameView.getHeight() - height); xSpeed = rnd.nextInt(MAX_SPEED * 2) - MAX_SPEED; ySpeed = rnd.nextInt(MAX_SPEED * 2) - MAX_SPEED; } private void update() { if (x >= gameView.getWidth() - width - xSpeed || x + xSpeed <= 0) { xSpeed = -xSpeed; } x = x + xSpeed; if (y >= gameView.getHeight() - height - ySpeed || y + ySpeed <= 0) { ySpeed = -ySpeed; } y = y + ySpeed; currentFrame = ++currentFrame % BMP_COLUMNS; } public void onDraw(Canvas canvas) { update(); int srcX = currentFrame * width; int srcY = getAnimationRow() * height; Rect src = new Rect(srcX, srcY, srcX + width, srcY + height); Rect dst = new Rect(x, y, x + width, y + height); canvas.drawBitmap(bmp, src, dst, null); } private int getAnimationRow() { double dirDouble = (Math.atan2(xSpeed, ySpeed) / (Math.PI / 2) + 2); int direction = (int) Math.round(dirDouble) % BMP_ROWS; return DIRECTION_TO_ANIMATION_MAP[direction]; } public boolean isCollision(float x2, float y2){ return x2 > x && x2 < x + width && y2 > y && y2 < y + height; } public boolean isCollision(Beam other) { // TODO Auto-generated method stub if(this.left>other.right || other.left<other.right)return false; if(this.bottom>other.top || other.bottom<other.top)return false; return true; } } Bullet Class: public class Bullet { int mX; int mY; private Bitmap mBitmap; //bounding box left<right and top>bottom int left ; int right ; int top ; int bottom ; public Bullet (Bitmap mBitmap){ this.mBitmap = mBitmap; } public void draw(Canvas canvas, int mX, int mY) { this.mX = mX; this.mY = mY; canvas.drawBitmap(mBitmap, mX, mY, null); } }

  Read the article

• Accelerating 2d object collision with other objects [on hold]

  - by Silent Cave

  Making my very first attempt at game programming with SDL/OpenGL. So I made an object Actor witch can move in all four sides with acceleration. And there are bunch of other rectangles to collide to. the image Movement and collision detection alghorythms work just fine by itself, but when combined to prevent the green rectangle from crossing black rectangles, it gives me a kind of funny resault. Let me show you the code first: from Actor.h class Actor{ public: SDL_Rect * dim; alphaColor * col; float speed; float xlGrav, xrGrav, yuGrav, ydGrav; float acceleration; bool left,right,up,down; Actor(SDL_Rect * dim,alphaColor * col, float speed, float acceleration); bool colides(const SDL_Rect & rect); bool check_for_collisions(const std::vector<SDL_Rect*> & gameObjects ); }; from actor.cpp bool Actor::colides(const SDL_Rect & rect){ if (dim->x + dim->w < rect.x) return false; if (dim->x > rect.x + rect.w) return false; if (dim->y + dim->h < rect.y) return false; if (dim->y > rect.y + rect.h) return false; return true; } movement logic from main.cpp if (actor->left){ if(actor->xlGrav < actor->speed){ actor->xlGrav += actor->speed*actor->acceleration; }else actor->xlGrav = actor->speed; actor->dim->x -= actor->xlGrav; if(actor->check_for_collisions(gameObjects)){ actor->dim->x += actor->xlGrav; actor->xlGrav = 0; } } if (!actor->left){ if(actor->xlGrav - actor->speed*actor->acceleration > 0){ actor->xlGrav -= actor->speed*actor->acceleration; }else actor->xlGrav = 0; actor->dim->x -= actor->xlGrav; if(actor->check_for_collisions(gameObjects)){ actor->dim->x += actor->xlGrav; actor->xlGrav = 0; } } if (actor->right){ if(actor->xrGrav < actor->speed){ actor->xrGrav += actor->speed*actor->acceleration; }else actor->xrGrav = actor->speed; actor->dim->x += actor->xrGrav; if(actor->check_for_collisions(gameObjects)){ actor->dim->x -= actor->xrGrav; actor->xrGrav = 0; } } if (!actor->right){ if(actor->xrGrav - actor->speed*actor->acceleration > 0){ actor->xrGrav -= actor->speed*actor->acceleration; }else actor->xrGrav = 0; actor->dim->x += actor->xrGrav; if(actor->check_for_collisions(gameObjects)){ actor->dim->x -= actor->xrGrav; actor->xrGrav = 0; } } if (actor->up){ if(actor->yuGrav < actor->speed){ actor->yuGrav += actor->speed*actor->acceleration; }else actor->yuGrav = actor->speed; actor->dim->y -= actor->yuGrav; if(actor->check_for_collisions(gameObjects)){ actor->dim->y += actor->yuGrav; actor->yuGrav = 0; } } if (!actor->up){ if(actor->yuGrav - actor->speed*actor->acceleration > 0){ actor->yuGrav -= actor->speed*actor->acceleration; }else actor->yuGrav = 0; actor->dim->y -= actor->yuGrav; if(actor->check_for_collisions(gameObjects)){ actor->dim->y += actor->yuGrav; actor->yuGrav = 0; } } if (actor->down){ if(actor->ydGrav < actor->speed){ actor->ydGrav += actor->speed*actor->acceleration; }else actor->ydGrav = actor->speed; actor->dim->y += actor->ydGrav; if(actor->check_for_collisions(gameObjects)){ actor->dim->y -= actor->ydGrav; actor->ydGrav = 0; } } if (!actor->down){ if(actor->ydGrav - actor->speed*actor->acceleration > 0){ actor->ydGrav -= actor->speed*actor->acceleration; }else actor->ydGrav = 0; actor->dim->y += actor->ydGrav; if(actor->check_for_collisions(gameObjects)){ actor->dim->y -= actor->ydGrav; actor->ydGrav = 0; } } So, if the green box approaches an obstacle from up or left, everything goes as planned - object stops, and it's acceleration drops to zero. But if it comes from bottom or right, it enters into obstacles inner space and starts strangely dance, I'd rather say move in inverted controls. What do I fail to see?

  Read the article

• Relative cam movement and momentum on arbitrary surface

  - by user29244

  I have been working on a game for quite long, think sonic classic physics in 3D or tony hawk psx, with unity3D. However I'm stuck at the most fundamental aspect of movement. The requirement is that I need to move the character in mario 64 fashion (or sonic adventure) aka relative cam input: the camera's forward direction always point input forward the screen, left or right input point toward left or right of the screen. when input are resting, the camera direction is independent from the character direction and the camera can orbit the character when input are pressed the character rotate itself until his direction align with the direction the input is pointing at. It's super easy to do as long your movement are parallel to the global horizontal (or any world axis). However when you try to do this on arbitrary surface (think moving along complex curved surface) with the character sticking to the surface normal (basically moving on wall and ceiling freely), it seems harder. What I want is to achieve the same finesse of movement than in mario but on arbitrary angled surfaces. There is more problem (jumping and transitioning back to the real world alignment and then back on a surface while keeping momentum) but so far I didn't even take off the basics. So far I have accomplish moving along the curved surface and the relative cam input, but for some reason direction fail all the time (point number 3, the character align slowly to the input direction). Do you have an idea how to achieve that? Here is the code and some demo so far: The demo: https://dl.dropbox.com/u/24530447/flash%20build/litesonicengine/LiteSonicEngine5.html Camera code: using UnityEngine; using System.Collections; public class CameraDrive : MonoBehaviour { public GameObject targetObject; public Transform camPivot, camTarget, camRoot, relcamdirDebug; float rot = 0; //---------------------------------------------------------------------------------------------------------- void Start() { this.transform.position = targetObject.transform.position; this.transform.rotation = targetObject.transform.rotation; } void FixedUpdate() { //the pivot system camRoot.position = targetObject.transform.position; //input on pivot orientation rot = 0; float mouse_x = Input.GetAxisRaw( "camera_analog_X" ); // rot = rot + ( 0.1f * Time.deltaTime * mouse_x ); // wrapAngle( rot ); // //when the target object rotate, it rotate too, this should not happen UpdateOrientation(this.transform.forward,targetObject.transform.up); camRoot.transform.RotateAround(camRoot.transform.up,rot); //debug the relcam dir RelativeCamDirection() ; //this camera this.transform.position = camPivot.position; //set the camera to the pivot this.transform.LookAt( camTarget.position ); // } //---------------------------------------------------------------------------------------------------------- public float wrapAngle ( float Degree ) { while (Degree < 0.0f) { Degree = Degree + 360.0f; } while (Degree >= 360.0f) { Degree = Degree - 360.0f; } return Degree; } private void UpdateOrientation( Vector3 forward_vector, Vector3 ground_normal ) { Vector3 projected_forward_to_normal_surface = forward_vector - ( Vector3.Dot( forward_vector, ground_normal ) ) * ground_normal; camRoot.transform.rotation = Quaternion.LookRotation( projected_forward_to_normal_surface, ground_normal ); } float GetOffsetAngle( float targetAngle, float DestAngle ) { return ((targetAngle - DestAngle + 180)% 360) - 180; } //---------------------------------------------------------------------------------------------------------- void OnDrawGizmos() { Gizmos.DrawCube( camPivot.transform.position, new Vector3(1,1,1) ); Gizmos.DrawCube( camTarget.transform.position, new Vector3(1,5,1) ); Gizmos.DrawCube( camRoot.transform.position, new Vector3(1,1,1) ); } void OnGUI() { GUI.Label(new Rect(0,80,1000,20*10), "targetObject.transform.up : " + targetObject.transform.up.ToString()); GUI.Label(new Rect(0,100,1000,20*10), "target euler : " + targetObject.transform.eulerAngles.y.ToString()); GUI.Label(new Rect(0,100,1000,20*10), "rot : " + rot.ToString()); } //---------------------------------------------------------------------------------------------------------- void RelativeCamDirection() { float input_vertical_movement = Input.GetAxisRaw( "Vertical" ), input_horizontal_movement = Input.GetAxisRaw( "Horizontal" ); Vector3 relative_forward = Vector3.forward, relative_right = Vector3.right, relative_direction = ( relative_forward * input_vertical_movement ) + ( relative_right * input_horizontal_movement ) ; MovementController MC = targetObject.GetComponent<MovementController>(); MC.motion = relative_direction.normalized * MC.acceleration * Time.fixedDeltaTime; MC.motion = this.transform.TransformDirection( MC.motion ); //MC.transform.Rotate(Vector3.up, input_horizontal_movement * 10f * Time.fixedDeltaTime); } } Mouvement code: using UnityEngine; using System.Collections; public class MovementController : MonoBehaviour { public float deadZoneValue = 0.1f, angle, acceleration = 50.0f; public Vector3 motion ; //-------------------------------------------------------------------------------------------- void OnGUI() { GUILayout.Label( "transform.rotation : " + transform.rotation ); GUILayout.Label( "transform.position : " + transform.position ); GUILayout.Label( "angle : " + angle ); } void FixedUpdate () { Ray ground_check_ray = new Ray( gameObject.transform.position, -gameObject.transform.up ); RaycastHit raycast_result; Rigidbody rigid_body = gameObject.rigidbody; if ( Physics.Raycast( ground_check_ray, out raycast_result ) ) { Vector3 next_position; //UpdateOrientation( gameObject.transform.forward, raycast_result.normal ); UpdateOrientation( gameObject.transform.forward, raycast_result.normal ); next_position = GetNextPosition( raycast_result.point ); rigid_body.MovePosition( next_position ); } } //-------------------------------------------------------------------------------------------- private void UpdateOrientation( Vector3 forward_vector, Vector3 ground_normal ) { Vector3 projected_forward_to_normal_surface = forward_vector - ( Vector3.Dot( forward_vector, ground_normal ) ) * ground_normal; transform.rotation = Quaternion.LookRotation( projected_forward_to_normal_surface, ground_normal ); } private Vector3 GetNextPosition( Vector3 current_ground_position ) { Vector3 next_position; // //-------------------------------------------------------------------- // angle = 0; // Vector3 dir = this.transform.InverseTransformDirection(motion); // angle = Vector3.Angle(Vector3.forward, dir);// * 1f * Time.fixedDeltaTime; // // if(angle > 0) this.transform.Rotate(0,angle,0); // //-------------------------------------------------------------------- next_position = current_ground_position + gameObject.transform.up * 0.5f + motion ; return next_position; } } Some observation: I have the correct input, I have the correct translation in the camera direction ... but whenever I attempt to slowly lerp the direction of the character in direction of the input, all I get is wild spin! Sad Also discovered that strafing to the right (immediately at the beginning without moving forward) has major singularity trapping on the equator!! I'm totally lost and crush (I have already done a much more featured version which fail at the same aspect)

  Read the article

• PASS: The Legal Stuff

  - by Bill Graziano

  I wanted to give a little background on the legal status of PASS.  The Professional Association for SQL Server (PASS) is an American corporation chartered in the state of Illinois.  In America a corporation has to be chartered in a particular state.  It has to abide by the laws of that state and potentially pay taxes to that state.  Our bylaws and actions have to comply with Illinois state law and United States law.  We maintain a mailing address in Chicago, Illinois but our headquarters is currently in Vancouver, Canada. We have roughly a dozen people that work in our Vancouver headquarters and 4-5 more that work remotely on various projects.  These aren’t employees of PASS.  They are employed by a management company that we hire to run the day to day operations of the organization.  I’ll have more on this arrangement in a future post. PASS is a non-profit corporation.  The term non-profit and not-for-profit are used interchangeably.  In a for-profit corporation (or LLC) there are owners that are entitled to the profits of a company.  In a non-profit there are no owners.  As a non-profit, all the money earned by the organization must be retained or spent.  There is no money that flows out to shareholders, owners or the board of directors.  Any money not spent in furtherance of our mission is retained as financial reserves. Many non-profits apply for tax exempt status.  Being tax exempt means that an organization doesn’t pay taxes on its profits.  There are a variety of laws governing who can be tax exempt in the United States.  There are many professional associations that are tax exempt however PASS isn’t tax exempt.  Because our mission revolves around the software of a single company we aren’t eligible for tax exempt status. PASS was founded in the late 1990’s by Microsoft and Platinum Technologies.  Platinum was later purchased by Computer Associates. As the founding partners Microsoft and CA each have two seats on the Board of Directors.  The other six directors and three officers are elected as specified in our bylaws. As a non-profit, our bylaws layout our governing practices.  They must conform to Illinois and United States law.  These bylaws specify that PASS is governed by a Board of Directors elected by the membership with two members each from Microsoft and CA.  You can find our bylaws as well as a proposed update to them on the governance page of the PASS web site. The last point that I’d like to make is that PASS is completely self-funded.  All of our $4 million in revenue comes from conference registrations, sponsorships and advertising.  We don’t receive any money from anyone outside those channels.  While we work closely with Microsoft we are independent of them and only derive a very small percentage of our revenue from them.

  Read the article

• Android Bitmap : collision Detecting [on hold]

  - by user2505374

  I am writing an Android game right now and I would need some help in the collision of the wall on screen. When I drag the ball in the top and right it able to collide in wall but when I drag it faster it was able to overlap in the wall. public boolean onTouchEvent(MotionEvent event) { int x = (int) event.getX(); int y = (int) event.getY(); switch (event.getAction()) { // if the player moves case MotionEvent.ACTION_MOVE: { if (playerTouchRect.contains(x, y)) { boolean left = false; boolean right = false; boolean up = false; boolean down = false; boolean canMove = false; boolean foundFinish = false; if (x != pLastXPos) { if (x < pLastXPos) { left = true; } else { right = true; } pLastXPos = x; } if (y != pLastYPos) { if (y < pLastYPos) { up = true; } else { down = true; } pLastYPos = y; } plCellRect = getRectFromPos(x, y); newplRect.set(playerRect); newplRect.left = x - (int) (playerRect.width() / 2); newplRect.right = x + (int) (playerRect.width() / 2); newplRect.top = y - (int) (playerRect.height() / 2); newplRect.bottom = y + (int) (playerRect.height() / 2); int currentRow = 0; int currentCol = 0; currentRow = getRowFromYPos(newplRect.top); currentCol = getColFromXPos(newplRect.right); if(!canMove){ canMove = mapManager.getCurrentTile().pMaze[currentRow][currentCol] == Cell.wall; canMove =true; } finishTest = mapManager.getCurrentTile().pMaze[currentRow][currentCol]; foundA = finishTest == Cell.valueOf(letterNotGet + ""); canMove = mapManager.getCurrentTile().pMaze[currentRow][currentCol] != Cell.wall; canMove = (finishTest == Cell.floor || finishTest == Cell.pl) && canMove; if (canMove) { invalidate(); setTitle(); } if (foundA) { mapManager.getCurrentTile().pMaze[currentRow][currentCol] = Cell.floor; // finishTest letterGotten.add(letterNotGet); playCurrentLetter(); /*sounds.play(sExplosion, 1.0f, 1.0f, 0, 0, 1.5f);*/ foundS = letterNotGet == 's'; letterNotGet++; }if(foundS){ AlertDialog.Builder builder = new AlertDialog.Builder(mainActivity); builder.setTitle(mainActivity.getText(R.string.finished_title)); LayoutInflater inflater = mainActivity.getLayoutInflater(); View view = inflater.inflate(R.layout.finish, null); builder.setView(view); View closeButton =view.findViewById(R.id.closeGame); closeButton.setOnClickListener(new OnClickListener() { @Override public void onClick(View clicked) { if(clicked.getId() == R.id.closeGame) { mainActivity.finish(); } } }); AlertDialog finishDialog = builder.create(); finishDialog.show(); } else { Log.d(TAG, "INFO: updated player position"); playerRect.set(newplRect); setTouchZone(); updatePlayerCell(); } } // end of (CASE) if playerTouch break; } // end of (SWITCH) Case motion }//end of Switch return true; }//end of TouchEvent private void finish() { // TODO Auto-generated method stub } public int getColFromXPos(int xPos) { val = xPos / (pvWidth / mapManager.getCurrentTile().pCols); if (val == mapManager.getCurrentTile().pCols) { val = mapManager.getCurrentTile().pCols - 1; } return val; } /** * Given a y pixel position, return the row of the cell it is in This is * used when determining the type of adjacent Cells. * * @param yPos * y position in pixels * @return The cell this position is in */ public int getRowFromYPos(int yPos) { val = yPos / (pvHeight / mapManager.getCurrentTile().pRows); if (val == mapManager.getCurrentTile().pRows) { val = mapManager.getCurrentTile().pRows - 1; } return val; } /** * When preserving the position we need to know which cell the player is in, * so calculate it from the centre on its Rect */ public void updatePlayerCell() { plCell.x = (playerRect.left + (playerRect.width() / 2)) / (pvWidth / mapManager.getCurrentTile().pCols); plCell.y = (playerRect.top + (playerRect.height() / 2)) / (pvHeight / mapManager.getCurrentTile().pRows); if (mapManager.getCurrentTile().pMaze[plCell.y][plCell.x] == Cell.floor) { for (int row = 0; row < mapManager.getCurrentTile().pRows; row++) { for (int col = 0; col < mapManager.getCurrentTile().pCols; col++) { if (mapManager.getCurrentTile().pMaze[row][col] == Cell.pl) { mapManager.getCurrentTile().pMaze[row][col] = Cell.floor; break; } } } mapManager.getCurrentTile().pMaze[plCell.y][plCell.x] = Cell.pl; } } public Rect getRectFromPos(int x, int y) { calcCell.left = ((x / cellWidth) + 0) * cellWidth; calcCell.right = calcCell.left + cellWidth; calcCell.top = ((y / cellHeight) + 0) * cellHeight; calcCell.bottom = calcCell.top + cellHeight; Log.d(TAG, "Rect: " + calcCell + " Player: " + playerRect); return calcCell; } public void setPlayerRect(Rect newplRect) { playerRect.set(newplRect); } private void setTouchZone() { playerTouchRect.set( playerRect.left - playerRect.width() / TOUCH_ZONE, playerRect.top - playerRect.height() / TOUCH_ZONE, playerRect.right + playerRect.width() / TOUCH_ZONE, playerRect.bottom + playerRect.height() / TOUCH_ZONE); } public Rect getPlayerRect() { return playerRect; } public Point getPlayerCell() { return plCell; } public void setPlayerCell(Point cell) { plCell = cell; }

  Read the article

• 2D isometric picking

  - by Bikonja

  I'm trying to implement picking in my isometric 2D game, however, I am failing. First of all, I've searched for a solution and came to several, different equations and even a solution using matrices. I tried implementing every single one, but none of them seem to work for me. The idea is that I have an array of tiles, with each tile having it's x and y coordinates specified (in this simplified example it's by it's position in the array). I'm thinking that the tile (0, 0) should be on the left, (max, 0) on top, (0, max) on the bottom and (max, max) on the right. I came up with this loop for drawing, which googling seems to have verified as the correct solution, as has the rendered scene (ofcourse, it could still be wrong, also, forgive the messy names and stuff, it's just a WIP proof of concept code) // Draw code int col = 0; int row = 0; for (int i = 0; i < nrOfTiles; ++i) { // XOffset and YOffset are currently hardcoded values, but will represent camera offset combined with HUD offset Point tile = IsoToScreen(col, row, TileWidth / 2, TileHeight / 2, XOffset, YOffset); int x = tile.X; int y = tile.Y; spriteBatch.Draw(_tiles[i], new Rectangle(tile.X, tile.Y, TileWidth, TileHeight), Color.White); col++; if (col >= Columns) // Columns is the number of tiles in a single row { col = 0; row++; } } // Get selection overlay location (removed check if selection exists for simplicity sake) Point tile = IsoToScreen(_selectedTile.X, _selectedTile.Y, TileWidth / 2, TileHeight / 2, XOffset, YOffset); spriteBatch.Draw(_selectionTexture, new Rectangle(tile.X, tile.Y, TileWidth, TileHeight), Color.White); // End of draw code public Point IsoToScreen(int isoX, int isoY, int widthHalf, int heightHalf, int xOffset, int yOffset) { Point newPoint = new Point(); newPoint.X = widthHalf * (isoX + isoY) + xOffset; newPoint.Y = heightHalf * (-isoX + isoY) + yOffset; return newPoint; } This code draws the tiles correctly. Now I wanted to do picking to select the tiles. For this, I tried coming up with equations of my own (including reversing the drawing equation) and I tried multiple solutions I found on the internet and none of these solutions worked. Trying out lots of solutions, I came upon one that didn't work, but it seemed like an axis was just inverted. I fiddled around with the equations and somehow managed to get it to actually work (but have no idea why it works), but while it's close, it still doesn't work. I'm not really sure how to describe the behaviour, but it changes the selection at wrong places, while being fairly close (sometimes spot on, sometimes a tile off, I believe never more off than the adjacent tile). This is the code I have for getting which tile coordinates are selected: public Point? ScreenToIso(int screenX, int screenY, int tileHeight, int offsetX, int offsetY) { Point? newPoint = null; int nX = -1; int nY = -1; int tX = screenX - offsetX; int tY = screenY - offsetY; nX = -(tY - tX / 2) / tileHeight; nY = (tY + tX / 2) / tileHeight; newPoint = new Point(nX, nY); return newPoint; } I have no idea why this code is so close, especially considering it doesn't even use the tile width and all my attempts to write an equation myself or use a solution I googled failed. Also, I don't think this code accounts for the area outside the "tile" (the transparent part of the tile image), for which I intend to add a color map, but even if that's true, it's not the problem as the selection sometimes switches on approx 25% or 75% of width or height. I'm thinking I've stumbled upon a wrong path and need to backtrack, but at this point, I'm not sure what to do so I hope someone can shed some light on my error or point me to the right path. It may be worth mentioning that my goal is to not only pick the tile. Each main tile will be divided into 5x5 smaller tiles which won't be drawn seperately from the whole main tile, but they will need to be picked out. I think a color map of a main tile with different colors for different coordinates within the main tile should take care of that though, which would fall within using a color map for the main tile (for the transparent parts of the tile, meaning parts that possibly belong to other tiles).

  Read the article

• How to break out of if statement

  - by TheBroodian

  I'm not sure if the title is exactly an accurate representation of what I'm actually trying to ask, but that was the best I could think of. I am experiencing an issue with my character class. I have developed a system so that he can perform chain attacks, and something that was important to me was that 1)button presses during the process of an attack wouldn't interrupt the character, and 2) at the same time, button presses should be stored so that the player can smoothly queue up chain attacks in the middle of one so that gameplay doesn't feel rigid or unresponsive. This all begins when the player presses the punch button. Upon pressing the punch button, the game checks the state of the dpad at the moment of the button press, and then translates the resulting combined buttons into an int which I use as an enumerator relating to a punch method for the character. The enumerator is placed into a List so that the next time the character's Update() method is called, it will execute the next punch in the list. It only executes the next punch if my character is flagged with acceptInput as true. All attacks flag acceptInput as false, to prevent the interruption of attacks, and then at the end of an attack, acceptInput is set back to true. While accepting input, all other actions are polled for, i.e. jumping, running, etc. In runtime, if I attack, and then queue up another attack behind it (by pressing forward+punch) I can see the second attack visibly execute, which should flag acceptInput as false, yet it gets interrupted and my character will stop punching and start running if I am still holding down the dpad. Included is some code for context. This is the input region for my character. //Placed this outside the if (acceptInput) tree because I want it //to be taken into account whether we are accepting input or not. //This will queue up attacks, which will only be executed if we are accepting input. //This creates a desired effect that helps control the character in a // smoother fashion for the player. if (Input.justPressed(buttonManager.Punch)) { int dpadPressed = Input.DpadState(0); if (attackBuffer.Count() < 1) { attackBuffer.Add(CheckPunch(dpadPressed)); } else { attackBuffer.Clear(); attackBuffer.Add(CheckPunch(dpadPressed)); } } if (acceptInput) { if (attackBuffer.Count() > 0) { ExecutePunch(attackBuffer[0]); attackBuffer.RemoveAt(0); } //If D-Pad left is being held down. if (Input.DpadDirectionHeld(0, buttonManager.Left)) { flipped = false; if (onGround) { newAnimation = "run"; } velocity = new Vector2(velocity.X - acceleration, velocity.Y); if (walking == true && velocity.X <= -walkSpeed) { velocity.X = -walkSpeed; } else if (walking == false && velocity.X <= -maxSpeed) { velocity.X = -maxSpeed; } } //If D-Pad right is being held down. if (Input.DpadDirectionHeld(0, buttonManager.Right)) { flipped = true; if (onGround) { newAnimation = "run"; } velocity = new Vector2(velocity.X + acceleration, velocity.Y); if (walking == true && velocity.X >= walkSpeed) { velocity.X = walkSpeed; } else if (walking == false && velocity.X >= maxSpeed) { velocity.X = maxSpeed; } } //If jump/accept button is pressed. if (Input.justPressed(buttonManager.JumpAccept)) { if (onGround) { Jump(); } } //If toggle element next button is pressed. if (Input.justPressed(buttonManager.ToggleElementNext)) { if (elements.Count != 0) { elementInUse++; if (elementInUse >= elements.Count) { elementInUse = 0; } } } //If toggle element last button is pressed. if (Input.justPressed(buttonManager.ToggleElementLast)) { if (elements.Count != 0) { elementInUse--; if (elementInUse < 0) { elementInUse = Convert.ToSByte(elements.Count() - 1); } } } //If character is in the process of jumping. if (jumping == true) { if (Input.heldDown(buttonManager.JumpAccept)) { velocity.Y -= fallSpeed.Y; maxJumpTime -= elapsed; } if (Input.justReleased(buttonManager.JumpAccept) || maxJumpTime <= 0) { jumping = false; maxJumpTime = 0; } } //Won't execute abilities if input isn't being accepted. foreach (PlayerAbility ability in playerAbilities) { if (buffer.Matches(ability)) { if (onGround) { ability.Activate(); } if (!onGround && ability.UsableInAir) { ability.Activate(); } else if (!onGround && !ability.UsableInAir) { buffer.Clear(); } } } } When the attackBuffer calls ExecutePunch(int) method, ExecutePunch() will call one of the following methods: private void NeutralPunch1() //0 { acceptInput = false; busy = true; newAnimation = "punch1"; numberOfAttacks++; timeSinceLastAttack = 0; } private void ForwardPunch2(bool toLeft) //true == 7, false == 4 { forwardPunch2Timer = 0f; acceptInput = false; busy = true; newAnimation = "punch2begin"; numberOfAttacks++; timeSinceLastAttack = 0; if (toLeft) { velocity.X -= 800; } if (!toLeft) { velocity.X += 800; } } I assume the attack is being interrupted due to the fact that ExecutePunch() is in the same if statement as running, but I haven't been able to find a suitable way to stop this happening. Thank you ahead of time for reading this, I apologize for it having become so long winded.

  Read the article

• Space invaders clone not moving properly

  - by ThePlan

  I'm trying to make a basic space invaders clone in allegro 5, I've got my game set up, basic events and such, here is the code: #include <allegro5/allegro.h> #include <allegro5/allegro_image.h> #include <allegro5/allegro_primitives.h> #include <allegro5/allegro_font.h> #include <allegro5/allegro_ttf.h> #include "Entity.h" // GLOBALS ========================================== const int width = 500; const int height = 500; const int imgsize = 3; bool key[5] = {false, false, false, false, false}; bool running = true; bool draw = true; // FUNCTIONS ======================================== void initSpaceship(Spaceship &ship); void moveSpaceshipRight(Spaceship &ship); void moveSpaceshipLeft(Spaceship &ship); void initInvader(Invader &invader); void moveInvaderRight(Invader &invader); void moveInvaderLeft(Invader &invader); void initBullet(Bullet &bullet); void fireBullet(); void doCollision(); void updateInvaders(); void drawText(); enum key_t { UP, DOWN, LEFT, RIGHT, SPACE }; enum source_t { INVADER, DEFENDER }; int main(void) { if(!al_init()) { return -1; } Spaceship ship; Invader invader; Bullet bullet; al_init_image_addon(); al_install_keyboard(); al_init_font_addon(); al_init_ttf_addon(); ALLEGRO_DISPLAY *display = al_create_display(width, height); ALLEGRO_EVENT_QUEUE *event_queue = al_create_event_queue(); ALLEGRO_TIMER *timer = al_create_timer(1.0 / 60); ALLEGRO_BITMAP *images[imgsize]; ALLEGRO_FONT *font1 = al_load_font("arial.ttf", 20, 0); al_register_event_source(event_queue, al_get_keyboard_event_source()); al_register_event_source(event_queue, al_get_display_event_source(display)); al_register_event_source(event_queue, al_get_timer_event_source(timer)); images[0] = al_load_bitmap("defender.bmp"); images[1] = al_load_bitmap("invader.bmp"); images[2] = al_load_bitmap("explosion.bmp"); al_convert_mask_to_alpha(images[0], al_map_rgb(0, 0, 0)); al_convert_mask_to_alpha(images[1], al_map_rgb(0, 0, 0)); al_convert_mask_to_alpha(images[2], al_map_rgb(0, 0, 0)); initSpaceship(ship); initBullet(bullet); initInvader(invader); al_start_timer(timer); while(running) { ALLEGRO_EVENT ev; al_wait_for_event(event_queue, &ev); if(ev.type == ALLEGRO_EVENT_TIMER) { draw = true; if(key[RIGHT] == true) moveSpaceshipRight(ship); if(key[LEFT] == true) moveSpaceshipLeft(ship); } else if(ev.type == ALLEGRO_EVENT_DISPLAY_CLOSE) running = false; else if(ev.type == ALLEGRO_EVENT_KEY_DOWN) { switch(ev.keyboard.keycode) { case ALLEGRO_KEY_ESCAPE: running = false; break; case ALLEGRO_KEY_LEFT: key[LEFT] = true; break; case ALLEGRO_KEY_RIGHT: key[RIGHT] = true; break; case ALLEGRO_KEY_SPACE: key[SPACE] = true; break; } } else if(ev.type == ALLEGRO_KEY_UP) { switch(ev.keyboard.keycode) { case ALLEGRO_KEY_LEFT: key[LEFT] = false; break; case ALLEGRO_KEY_RIGHT: key[RIGHT] = false; break; case ALLEGRO_KEY_SPACE: key[SPACE] = false; break; } } if(draw && al_is_event_queue_empty(event_queue)) { draw = false; al_draw_bitmap(images[0], ship.pos_x, ship.pos_y, 0); al_flip_display(); al_clear_to_color(al_map_rgb(0, 0, 0)); } } al_destroy_font(font1); al_destroy_event_queue(event_queue); al_destroy_timer(timer); for(int i = 0; i < imgsize; i++) al_destroy_bitmap(images[i]); al_destroy_display(display); } // FUNCTION LOGIC ====================================== void initSpaceship(Spaceship &ship) { ship.lives = 3; ship.speed = 2; ship.pos_x = width / 2; ship.pos_y = height - 20; } void initInvader(Invader &invader) { invader.health = 100; invader.count = 40; invader.speed = 0.5; invader.pos_x = 300; invader.pos_y = 300; } void initBullet(Bullet &bullet) { bullet.speed = 10; } void moveSpaceshipRight(Spaceship &ship) { ship.pos_x += ship.speed; if(ship.pos_x >= width) ship.pos_x = width-30; } void moveSpaceshipLeft(Spaceship &ship) { ship.pos_x -= ship.speed; if(ship.pos_x <= 0) ship.pos_x = 0+30; } However it's not behaving the way I want it to behave, in fact the behavior for the ship movement is un-normal. Basically I specified that the ship only moves when the right/left key is down, however the ship is moving constantly to the direction of the key pressed, it never stops although it should only move while my key is down. Even more weird behavior, when I press the opposite key the ship completely stops no matter what else I press. What's wrong with the code? Why does the ship move constantly even after I specified it only moves when a key is down?

  Read the article

• Objects won't render when Texture Compression + Mipmapping is Enabled

  - by felipedrl

  I'm optimizing my game and I've just implemented compressed (DXTn) texture loading in OpenGL. I've worked my way removing bugs but I can't figure out this one: objects w/ DXTn + mipmapped textures are not being rendered. It's not like they are appearing with a flat color, they just don't appear at all. DXTn textured objs render and mipmapped non-compressed textures render just fine. The texture in question is 256x256 I generate the mips all the way down 4x4, i.e 1 block. I've checked on gDebugger and it display all the levels (7) just fine. I'm using GL_LINEAR_MIPMAP_NEAREST for min filter and GL_LINEAR for mag one. The texture is being compressed and mipmaps being created offline with Paint.NET tool using super sampling method. (I also tried bilinear just in case) Source follow: [SNIPPET 1: Loading DDS into sys memory + Initializing Object] // Read header DDSHeader header; file.read(reinterpret_cast<char*>(&header), sizeof(DDSHeader)); uint pos = static_cast<uint>(file.tellg()); file.seekg(0, std::ios_base::end); uint dataSizeInBytes = static_cast<uint>(file.tellg()) - pos; file.seekg(pos, std::ios_base::beg); // Read file data mData = new unsigned char[dataSizeInBytes]; file.read(reinterpret_cast<char*>(mData), dataSizeInBytes); file.close(); mMipmapCount = header.mipmapcount; mHeight = header.height; mWidth = header.width; mCompressionType = header.pf.fourCC; // Only support files divisible by 4 (for compression blocks algorithms) massert(mWidth % 4 == 0 && mHeight % 4 == 0); massert(mCompressionType == NO_COMPRESSION || mCompressionType == COMPRESSION_DXT1 || mCompressionType == COMPRESSION_DXT3 || mCompressionType == COMPRESSION_DXT5); // Allow textures up to 65536x65536 massert(header.mipmapcount <= MAX_MIPMAP_LEVELS); mTextureFilter = TextureFilter::LINEAR; if (mMipmapCount > 0) { mMipmapFilter = MipmapFilter::NEAREST; } else { mMipmapFilter = MipmapFilter::NO_MIPMAP; } mBitsPerPixel = header.pf.bitcount; if (mCompressionType == NO_COMPRESSION) { if (header.pf.flags & DDPF_ALPHAPIXELS) { // The only format supported w/ alpha is A8R8G8B8 massert(header.pf.amask == 0xFF000000 && header.pf.rmask == 0xFF0000 && header.pf.gmask == 0xFF00 && header.pf.bmask == 0xFF); mInternalFormat = GL_RGBA8; mFormat = GL_BGRA; mDataType = GL_UNSIGNED_BYTE; } else { massert(header.pf.rmask == 0xFF0000 && header.pf.gmask == 0xFF00 && header.pf.bmask == 0xFF); mInternalFormat = GL_RGB8; mFormat = GL_BGR; mDataType = GL_UNSIGNED_BYTE; } } else { uint blockSizeInBytes = 16; switch (mCompressionType) { case COMPRESSION_DXT1: blockSizeInBytes = 8; if (header.pf.flags & DDPF_ALPHAPIXELS) { mInternalFormat = GL_COMPRESSED_RGBA_S3TC_DXT1_EXT; } else { mInternalFormat = GL_COMPRESSED_RGB_S3TC_DXT1_EXT; } break; case COMPRESSION_DXT3: mInternalFormat = GL_COMPRESSED_RGBA_S3TC_DXT3_EXT; break; case COMPRESSION_DXT5: mInternalFormat = GL_COMPRESSED_RGBA_S3TC_DXT5_EXT; break; default: // Not Supported (DXT2, DXT4 or any compression format) massert(false); } } [SNIPPET 2: Uploading into video memory] massert(mData != NULL); glGenTextures(1, &mHandle); massert(mHandle!=0); glBindTexture(GL_TEXTURE_2D, mHandle); commitFiltering(); uint offset = 0; Renderer* renderer = Renderer::getInstance(); switch (mInternalFormat) { case GL_RGB: case GL_RGBA: case GL_RGB8: case GL_RGBA8: for (uint i = 0; i < mMipmapCount + 1; ++i) { uint width = std::max(1U, mWidth >> i); uint height = std::max(1U, mHeight >> i); glTexImage2D(GL_TEXTURE_2D, i, mInternalFormat, width, height, mHasBorder, mFormat, mDataType, &mData[offset]); offset += width * height * (mBitsPerPixel / 8); } break; case GL_COMPRESSED_RGB_S3TC_DXT1_EXT: case GL_COMPRESSED_RGBA_S3TC_DXT1_EXT: case GL_COMPRESSED_RGBA_S3TC_DXT3_EXT: case GL_COMPRESSED_RGBA_S3TC_DXT5_EXT: { uint blockSize = 16; if (mInternalFormat == GL_COMPRESSED_RGB_S3TC_DXT1_EXT || mInternalFormat == GL_COMPRESSED_RGBA_S3TC_DXT1_EXT) { blockSize = 8; } uint width = mWidth; uint height = mHeight; for (uint i = 0; i < mMipmapCount + 1; ++i) { uint nBlocks = ((width + 3) / 4) * ((height + 3) / 4); // Only POT textures allowed for mipmapping massert(width % 4 == 0 && height % 4 == 0); glCompressedTexImage2D(GL_TEXTURE_2D, i, mInternalFormat, width, height, mHasBorder, nBlocks * blockSize, &mData[offset]); offset += nBlocks * blockSize; if (width <= 4 && height <= 4) { break; } width = std::max(4U, width / 2); height = std::max(4U, height / 2); } break; } default: // Not Supported massert(false); } Also I don't understand the "+3" in the block size computation but looking for a solution for my problema I've encountered people defining it as that. I guess it won't make a differente for POT textures but I put just in case. Thanks.

  Read the article

• Indexed Drawing in OpenGL not working

  - by user2050846

  I am trying to render 2 types of primitives- - points ( a Point Cloud ) - triangles ( a Mesh ) I am rendering points simply without any index arrays and they are getting rendered fine. To render the meshes I am using indexed drawing with the face list array having the indices of the vertices to be rendered as Triangles. Vertices and their corresponding vertex colors are stored in their corresponding buffers. But the indexed drawing command do not draw anything. The code is as follows- Main Display Function: void display() { simple->enable(); simple->bindUniform("MV",modelview); simple->bindUniform("P", projection); // rendering Point Cloud glBindVertexArray(vao); // Vertex buffer Point Cloud glBindBuffer(GL_ARRAY_BUFFER,vertexbuffer); glEnableVertexAttribArray(0); glVertexAttribPointer(0,3,GL_FLOAT,GL_FALSE,0,0); // Color Buffer point Cloud glBindBuffer(GL_ARRAY_BUFFER,colorbuffer); glEnableVertexAttribArray(1); glVertexAttribPointer(1,3,GL_FLOAT,GL_FALSE,0,0); // Render Colored Point Cloud //glDrawArrays(GL_POINTS,0,model->vertexCount); glDisableVertexAttribArray(0); glDisableVertexAttribArray(1); // ---------------- END---------------------// //// Floor Rendering glBindBuffer(GL_ARRAY_BUFFER,fl); glEnableVertexAttribArray(0); glEnableVertexAttribArray(1); glVertexAttribPointer(0,3,GL_FLOAT,GL_FALSE,0,0); glVertexAttribPointer(1,4,GL_FLOAT,GL_FALSE,0,(void *)48); glDrawArrays(GL_QUADS,0,4); glDisableVertexAttribArray(0); glDisableVertexAttribArray(1); // -----------------END---------------------// //Rendering the Meshes //////////// PART OF CODE THAT IS NOT DRAWING ANYTHING //////////////////// glBindVertexArray(vid); for(int i=0;i<NUM_MESHES;i++) { glBindBuffer(GL_ARRAY_BUFFER,mVertex[i]); glEnableVertexAttribArray(0); glEnableVertexAttribArray(1); glVertexAttribPointer(0,3,GL_FLOAT,GL_FALSE,0,0); glVertexAttribPointer(1,3,GL_FLOAT,GL_FALSE,0,(void *)(meshes[i]->vertexCount*sizeof(glm::vec3))); //glDrawArrays(GL_TRIANGLES,0,meshes[i]->vertexCount); glBindBuffer(GL_ELEMENT_ARRAY_BUFFER,mFace[i]); //cout<<gluErrorString(glGetError()); glDrawElements(GL_TRIANGLES,meshes[i]->faceCount*3,GL_FLOAT,(void *)0); glDisableVertexAttribArray(0); glDisableVertexAttribArray(1); } glUseProgram(0); glutSwapBuffers(); glutPostRedisplay(); } Point Cloud Buffer Allocation Initialization: void initGLPointCloud() { glGenBuffers(1,&vertexbuffer); glGenBuffers(1,&colorbuffer); glGenBuffers(1,&fl); //Populates the position buffer glBindBuffer(GL_ARRAY_BUFFER,vertexbuffer); glBufferData(GL_ARRAY_BUFFER, model->vertexCount * sizeof (glm::vec3), &model->positions[0], GL_STATIC_DRAW); //Populates the color buffer glBindBuffer(GL_ARRAY_BUFFER, colorbuffer); glBufferData(GL_ARRAY_BUFFER, model->vertexCount * sizeof (glm::vec3), &model->colors[0], GL_STATIC_DRAW); model->FreeMemory(); // To free the not needed memory, as the data has been already // copied on graphic card, and wont be used again. glBindBuffer(GL_ARRAY_BUFFER,0); } Meshes Buffer Initialization: void initGLMeshes(int i) { glBindBuffer(GL_ARRAY_BUFFER,mVertex[i]); glBufferData(GL_ARRAY_BUFFER,meshes[i]->vertexCount*sizeof(glm::vec3)*2,NULL,GL_STATIC_DRAW); glBufferSubData(GL_ARRAY_BUFFER,0,meshes[i]->vertexCount*sizeof(glm::vec3),&meshes[i]->positions[0]); glBufferSubData(GL_ARRAY_BUFFER,meshes[i]->vertexCount*sizeof(glm::vec3),meshes[i]->vertexCount*sizeof(glm::vec3),&meshes[i]->colors[0]); glBindBuffer(GL_ELEMENT_ARRAY_BUFFER,mFace[i]); glBufferData(GL_ELEMENT_ARRAY_BUFFER,meshes[i]->faceCount*sizeof(glm::vec3), &meshes[i]->faces[0],GL_STATIC_DRAW); meshes[i]->FreeMemory(); //glBindBuffer(GL_ELEMENT_ARRAY_BUFFER,0); } Initialize the Rendering, load and create shader and calls the mesh and PCD initializers. void initRender() { simple= new GLSLShader("shaders/simple.vert","shaders/simple.frag"); //Point Cloud //Sets up VAO glGenVertexArrays(1, &vao); glBindVertexArray(vao); initGLPointCloud(); //floorData glBindBuffer(GL_ARRAY_BUFFER, fl); glBufferData(GL_ARRAY_BUFFER, sizeof(floorData), &floorData[0], GL_STATIC_DRAW); glBindBuffer(GL_ARRAY_BUFFER,0); glBindVertexArray(0); //Meshes for(int i=0;i<NUM_MESHES;i++) { if(i==0) // SET up the new vertex array state for indexed Drawing { glGenVertexArrays(1, &vid); glBindVertexArray(vid); glGenBuffers(NUM_MESHES,mVertex); glGenBuffers(NUM_MESHES,mColor); glGenBuffers(NUM_MESHES,mFace); } initGLMeshes(i); } glEnable(GL_DEPTH_TEST); } Any help would be much appreciated, I have been breaking my head on this problem since 3 days, and still it is unsolved.

  Read the article

• How do I make A* check all diagonal and orthogonal directions?

  - by Munezane

  I'm making a turn-based tactical game and I'm trying to implement the A* algorithm. I've been following a tutorial and got to this point, but my characters can't move diagonally up and left. Can anyone help me with this? The return x and y are int pointers which the characters are using to move towards the target. void level::aStar(int startx, int starty, int targetx, int targety, int* returnx, int* returny) { aStarGridSquare* currentSquare = new aStarGridSquare(); aStarGridSquare* startSquare = new aStarGridSquare(); aStarGridSquare* targetSquare = new aStarGridSquare(); aStarGridSquare* adjacentSquare = new aStarGridSquare(); aStarOpenList.clear(); for(unsigned int i=0; i<aStarGridSquareList.size(); i++) { aStarGridSquareList[i]->open=false; aStarGridSquareList[i]->closed=false; } startSquare=getaStarGridSquare(startx, starty); targetSquare=getaStarGridSquare(targetx, targety); if(startSquare==targetSquare) { *returnx=startx; *returny=starty; return; } startSquare->CostFromStart=0; startSquare->CostToTraverse=0; startSquare->parent = NULL; currentSquare=startSquare; aStarOpenList.push_back(currentSquare); while(currentSquare!=targetSquare && aStarOpenList.size()>0) { //unsigned int totalCostEstimate=aStarOpenList[0]->TotalCostEstimate; //currentSquare=aStarOpenList[0]; for(unsigned int i=0; i<aStarOpenList.size(); i++) { if(aStarOpenList.size()>1) { for(unsigned int j=1; j<aStarOpenList.size()-1; j++) { if(aStarOpenList[i]->TotalCostEstimate<aStarOpenList[j]->TotalCostEstimate) { currentSquare=aStarOpenList[i]; } else { currentSquare=aStarOpenList[j]; } } } else { currentSquare = aStarOpenList[i]; } } currentSquare->closed=true; currentSquare->open=false; for(unsigned int i=0; i<aStarOpenList.size(); i++) { if(aStarOpenList[i]==currentSquare) { aStarOpenList.erase(aStarOpenList.begin()+i); } } for(unsigned int i = currentSquare->blocky - 32; i <= currentSquare->blocky + 32; i+=32) { for(unsigned int j = currentSquare->blockx - 32; j<= currentSquare->blockx + 32; j+=32) { adjacentSquare=getaStarGridSquare(j/32, i/32); if(adjacentSquare!=NULL) { if(adjacentSquare->blocked==false && adjacentSquare->closed==false) { if(adjacentSquare->open==false) { adjacentSquare->parent=currentSquare; if(currentSquare->parent!=NULL) { currentSquare->CostFromStart = currentSquare->parent->CostFromStart + currentSquare->CostToTraverse + startSquare->CostFromStart; } else { currentSquare->CostFromStart=0; } adjacentSquare->CostFromStart =currentSquare->CostFromStart + adjacentSquare->CostToTraverse;// adjacentSquare->parent->CostFromStart + adjacentSquare->CostToTraverse; //currentSquare->CostToEndEstimate = abs(currentSquare->blockx - targetSquare->blockx) + abs(currentSquare->blocky - targetSquare->blocky); //currentSquare->TotalCostEstimate = currentSquare->CostFromStart + currentSquare->CostToEndEstimate; adjacentSquare->open = true; adjacentSquare->CostToEndEstimate=abs(adjacentSquare->blockx- targetSquare->blockx) + abs(adjacentSquare->blocky-targetSquare->blocky); adjacentSquare->TotalCostEstimate = adjacentSquare->CostFromStart+adjacentSquare->CostToEndEstimate; //adjacentSquare->open=true;*/ aStarOpenList.push_back(adjacentSquare); } else { if(adjacentSquare->parent->CostFromStart > currentSquare->CostFromStart) { adjacentSquare->parent=currentSquare; if(currentSquare->parent!=NULL) { currentSquare->CostFromStart = currentSquare->parent->CostFromStart + currentSquare->CostToTraverse + startSquare->CostFromStart; } else { currentSquare->CostFromStart=0; } adjacentSquare->CostFromStart =currentSquare->CostFromStart + adjacentSquare->CostToTraverse;// adjacentSquare->parent->CostFromStart + adjacentSquare->CostToTraverse; //currentSquare->CostToEndEstimate = abs(currentSquare->blockx - targetSquare->blockx) + abs(currentSquare->blocky - targetSquare->blocky); //currentSquare->TotalCostEstimate = currentSquare->CostFromStart + currentSquare->CostToEndEstimate; adjacentSquare->CostFromStart = adjacentSquare->parent->CostFromStart + adjacentSquare->CostToTraverse; adjacentSquare->CostToEndEstimate=abs(adjacentSquare->blockx - targetSquare->blockx) + abs(adjacentSquare->blocky - targetSquare->blocky); adjacentSquare->TotalCostEstimate = adjacentSquare->CostFromStart+adjacentSquare->CostToEndEstimate; } } } } } } } if(aStarOpenList.size()==0)//if empty { *returnx =startx; *returny =starty; return; } else { for(unsigned int i=0; i< aStarOpenList.size(); i++) { if(currentSquare->parent==NULL) { //int tempX = targetSquare->blockx; //int tempY = targetSquare->blocky; *returnx=targetSquare->blockx; *returny=targetSquare->blocky; break; } else { currentSquare=currentSquare->parent; } } } }

  Read the article

• Draw Bug 2D player Camera

  - by RedShft

  I have just implemented a 2D player camera for my game, everything works properly except the player on the screen jitters when it moves between tiles. What I mean by jitter, is that if the player is moving the camera updates the tileset to be drawn and if the player steps to the right, the camera snaps that way. The movement is not smooth. I'm guessing this is occurring because of how I implemented the function to calculate the current viewable area or how my draw function works. I'm not entirely sure how to fix this. This camera system was entirely of my own creation and a first attempt at that, so it's very possible this is not a great way of doing things. My camera class, pulls information from the current tileset and calculates the viewable area. Right now I am targettng a resolution of 800 by 600. So I try to fit the appropriate amount of tiles for that resolution. My camera class, after calculating the current viewable tileset relative to the players location, returns a slice of the original tileset to be drawn. This tileset slice is updated every frame according to the players position. This slice is then passed to the map class, which draws the tile on screen. //Map Draw Function //This draw function currently matches the GID of the tile to it's location on the //PNG file of the tileset and then draws this portion on the screen void Draw(SDL_Surface* background, int[] _tileSet) { enforce( tilesetImage != null, "Tileset is null!"); enforce( background != null, "BackGround is null!"); int i = 0; int j = 0; SDL_Rect DestR, SrcR; SrcR.x = 0; SrcR.y = 0; SrcR.h = 32; SrcR.w = 32; foreach(tile; _tileSet) { //This code is matching the current tiles ID to the tileset image SrcR.x = cast(short)(tileWidth * (tile >= 11 ? (tile - ((tile / 10) * 10) - 1) : tile - 1)); SrcR.y = cast(short)(tileHeight * (tile > 10 ? (tile / 10) : 0)); //Applying the tile to the surface SDL_BlitSurface( tilesetImage, &SrcR, background, &DestR ); //this keeps track of what column/row we are on i++; if ( i == mapWidth ) { i = 0; j++; } DestR.x = cast(short)(i * tileWidth); DestR.y = cast(short)(j * tileHeight); } } //Camera Class class Camera { private: //A rectangle representing the view area SDL_Rect viewArea; //In number of tiles int viewAreaWidth; int viewAreaHeight; //This is the x and y coordinate of the camera in MAP SPACE IN PIXELS vect2 cameraCoordinates; //The player location in map space IN PIXELS vect2 playerLocation; //This is the players location in screen space; vect2 playerScreenLoc; int playerTileCol; int playerTileRow; int cameraTileCol; int cameraTileRow; //The map is stored in a single array with the tile ids //this corresponds to the index of the starting and ending tile int cameraStartTile, cameraEndTile; //This is a slice of the current tile set int[] tileSetCopy; int mapWidth; int mapHeight; int tileWidth; int tileHeight; public: this() { this.viewAreaWidth = 25; this.viewAreaHeight = 19; this.cameraCoordinates = vect2(0, 0); this.playerLocation = vect2(0, 0); this.viewArea = SDL_Rect (0, 0, 0, 0); this.tileWidth = 32; this.tileHeight = 32; } void Init(vect2 playerPosition, ref int[] tileSet, int mapWidth, int mapHeight ) { playerLocation = playerPosition; this.mapWidth = mapWidth; this.mapHeight = mapHeight; CalculateCurrentCameraPosition( tileSet, playerPosition ); //writeln( "Tile Set Copy: ", tileSetCopy ); //writeln( "Orginal Tile Set: ", tileSet ); } void CalculateCurrentCameraPosition( ref int[] tileSet, vect2 playerPosition ) { playerLocation = playerPosition; playerTileCol = cast(int)((playerLocation.x / tileWidth) + 1); playerTileRow = cast(int)((playerLocation.y / tileHeight) + 1); //writeln( "Player Tile (Column, Row): ","(", playerTileCol, ", ", playerTileRow, ")"); cameraTileCol = playerTileCol - (viewAreaWidth / 2); cameraTileRow = playerTileRow - (viewAreaHeight / 2); CameraMapBoundsCheck(); //writeln( "Camera Tile Start (Column, Row): ","(", cameraTileCol, ", ", cameraTileRow, ")"); cameraStartTile = ( (cameraTileRow - 1) * mapWidth ) + cameraTileCol - 1; //writeln( "Camera Start Tile: ", cameraStartTile ); cameraEndTile = cameraStartTile + ( viewAreaWidth * viewAreaHeight ) * 2; //writeln( "Camera End Tile: ", cameraEndTile ); tileSetCopy = tileSet[cameraStartTile..cameraEndTile]; } vect2 CalculatePlayerScreenLocation() { cameraCoordinates.x = cast(float)(cameraTileCol * tileWidth); cameraCoordinates.y = cast(float)(cameraTileRow * tileHeight); playerScreenLoc = playerLocation - cameraCoordinates + vect2(32, 32);; //writeln( "Camera Coordinates: ", cameraCoordinates ); //writeln( "Player Location (Map Space): ", playerLocation ); //writeln( "Player Location (Screen Space): ", playerScreenLoc ); return playerScreenLoc; } void CameraMapBoundsCheck() { if( cameraTileCol < 1 ) cameraTileCol = 1; if( cameraTileRow < 1 ) cameraTileRow = 1; if( cameraTileCol + 24 > mapWidth ) cameraTileCol = mapWidth - 24; if( cameraTileRow + 19 > mapHeight ) cameraTileRow = mapHeight - 19; } ref int[] GetTileSet() { return tileSetCopy; } int GetViewWidth() { return viewAreaWidth; } }

  Read the article

• rotate player based off of joystick

  - by pengume

  Hey everyone I have this game that i am making in android and I have a touch screen joystick that moves the player around based on the joysticks position. I cant figure out how to also get the player to rotate at the same angle of the joystick. so when the joystick is to the left the players bitmap is rotated to the left as well. Maybe someone here has some sample code I could look at here is the joysticks class that I am using. `public class GameControls implements OnTouchListener { public float initx = DroidzActivity.screenWidth - 45; //255; // 320 og 425 public float inity = DroidzActivity.screenHeight - 45;//425; // 480 og 267 public Point _touchingPoint = new Point( DroidzActivity.screenWidth - 45, DroidzActivity.screenHeight - 45); public Point _pointerPosition = new Point(DroidzActivity.screenWidth - 100, DroidzActivity.screenHeight - 100); // ogx 220 ogy 150 private Boolean _dragging = false; private boolean attackMode = false; @Override public boolean onTouch(View v, MotionEvent event) { update(event); return true; } private MotionEvent lastEvent; public boolean ControlDragged; private static double angle; public void update(MotionEvent event) { if (event == null && lastEvent == null) { return; } else if (event == null && lastEvent != null) { event = lastEvent; } else { lastEvent = event; } // drag drop if (event.getAction() == MotionEvent.ACTION_DOWN) { if ((int) event.getX() > 0 && (int) event.getX() < 50 && (int) event.getY() > DroidzActivity.screenHeight - 160 && (int) event.getY() < DroidzActivity.screenHeight - 0) { setAttackMode(true); } else { _dragging = true; } } else if (event.getAction() == MotionEvent.ACTION_UP) { if(isAttackMode()){ setAttackMode(false); } _dragging = false; } if (_dragging) { ControlDragged = true; // get the pos _touchingPoint.x = (int) event.getX(); _touchingPoint.y = (int) event.getY(); // Log.d("GameControls", "x = " + _touchingPoint.x + " y = " //+ _touchingPoint.y); // bound to a box if (_touchingPoint.x < DroidzActivity.screenWidth - 75) { // og 400 _touchingPoint.x = DroidzActivity.screenWidth - 75; } if (_touchingPoint.x > DroidzActivity.screenWidth - 15) {// og 450 _touchingPoint.x = DroidzActivity.screenWidth - 15; } if (_touchingPoint.y < DroidzActivity.screenHeight - 75) {// og 240 _touchingPoint.y = DroidzActivity.screenHeight - 75; } if (_touchingPoint.y > DroidzActivity.screenHeight - 15) {// og 290 _touchingPoint.y = DroidzActivity.screenHeight - 15; } // get the angle setAngle(Math.atan2(_touchingPoint.y - inity, _touchingPoint.x - initx) / (Math.PI / 180)); // Move the ninja in proportion to how far // the joystick is dragged from its center _pointerPosition.y += Math.sin(getAngle() * (Math.PI / 180)) * (_touchingPoint.x / 70); // og 180 70 _pointerPosition.x += Math.cos(getAngle() * (Math.PI / 180)) * (_touchingPoint.x / 70); // make the pointer go thru if (_pointerPosition.x > DroidzActivity.screenWidth) { _pointerPosition.x = 0; } if (_pointerPosition.x < 0) { _pointerPosition.x = DroidzActivity.screenWidth; } if (_pointerPosition.y > DroidzActivity.screenHeight) { _pointerPosition.y = 0; } if (_pointerPosition.y < 0) { _pointerPosition.y = DroidzActivity.screenHeight; } } else if (!_dragging) { ControlDragged = false; // Snap back to center when the joystick is released _touchingPoint.x = (int) initx; _touchingPoint.y = (int) inity; // shaft.alpha = 0; } } public void setAttackMode(boolean attackMode) { this.attackMode = attackMode; } public boolean isAttackMode() { return attackMode; } public void setAngle(double angle) { this.angle = angle; } public static double getAngle() { return angle; } }` I should also note that the player has animations based on when he is moving or attacking. EDIT: I got the angle and am rotating the sprite around in the correct angle however it rotates on the wrong spot. My sprite is one giant bitmap that gets cut into four pieces and only one shown at a time to animate walking. here is the code I am using to rotate him right now. ` public void draw(Canvas canvas,int pointerX, int pointerY) { Matrix m; if (setRotation){ // canvas.save(); m = new Matrix(); m.reset(); // spriteWidth and spriteHeight are for just the current frame showed //m.setTranslate(spriteWidth / 2, spriteHeight / 2); //get and set rotation for ninja based off of joystick m.preRotate((float) GameControls.getRotation()); //create the rotated bitmap flipedSprite = Bitmap.createBitmap(bitmap , 0, 0,bitmap.getWidth(),bitmap.getHeight() , m, true); //set new bitmap to rotated ninja setBitmap(flipedSprite); setRotation = false; // canvas.restore(); Log.d("Ninja View", "angle of rotation= " +(float) GameControls.getRotation()); } ` And then the draw method // create the destination rectangle for the ninjas current animation frame // pointerX and pointerY are from the joystick moving the ninja around destRect = new Rect(pointerX, pointerY, pointerX + spriteWidth, pointerY + spriteHeight); canvas.drawBitmap(bitmap, getSourceRect(), destRect, null);

  Read the article

< Previous Page | 270 271 272 273 274 275 276 277 278 279 280 281  | Next Page >