Search Results

Search found 8410 results on 337 pages for 'hardware reserved'.

Page 275/337 | < Previous Page | 271 272 273 274 275 276 277 278 279 280 281 282  | Next Page >

• Put one monitor of a dual monitor windows system into standby

  - by Psycogeek

  Standby not Disabled! When running 2 monitors on windows 7 or Windows XP, I would like to be able to put one of the monitors at a time into standby. The method can be manual. When running 2 monitors , the second monitor is not always needed, shutting off the monitors own power switch will turn off the monitor, that does work Ok. Problems with that are , the delay with the monitor logo at turn on, and the power switch is not very accessable, and the switch might not live forever turning it on and off so many times. Using disable methods like devcon, WIN-P and Display, causes all the windows to properly move to the other monitor. While that is what a person would want to happen so they can get hold of the windows, that is not what I want to happen, and some things on the other monitor have to be re-arranged after a re-enable. By putting it into standby mode, nothing changes other than the monitor going into standby. Disconnecting the DVI cable still can cause the system to (properly) shift all the windows over to the one monitor, just like any of the disable methods do. That makes a mess of the windows, and is so unacceptable, that I would prefer to leave the monitor on, wasting power and the hardware, when it could easily go into standby for some time. For both monitors I am using a "MonitorOff" program that puts both monitors into standby, but I can not find a utility that will put only ONE monitor into standby for the windows system. If someone comes along and suggests "ultramon" you must know for a fact that it will put One of either of the monitors into actual standby. And it does not really suit me to use ultramon, I tested it (it was nice) and I did not feel that it was a program I wanted. The 2 monitors are running off of an ATI 4890 card, they are both hooked up DVI-I, the OS is both Windows 7 (primary) and Windows XP. In addition it would also be interesting to have seperate standby activity timers, and follow mouse kind of standby changes, but any manuel method , shortcut, batch , tray, or gadget kind of operation would be a good start.

  Read the article

• ESXi Server with 12 physical cores maxed out with only 8 cores assigned in virtual machines

  - by Sam

  I have an ESXi 5 server running on a 2-processor, 12-core system with hyperthreading enabled. So: 12 physical cores, 24 logical ones. On this server are 4 Windows 7 VMs, each configured for 2 processors, each running VMware Tools. Looking at my stats in vSphere, my "core utilization" is constantly maxed out. Yes, these machines are working hard, but only 8 cores have been allocated. How is this possible? Should I look into reducing the processor count per machine as in this post: VMware ESX server? I checked to ensure that hardware virtualization is enabled in the BIOS of the machine (a DELL R410). I've also started reading up on configuration, but being a newbie there's a lot of material to catch up on. It also seems I should only bother with advanced settings and pools if I'm really pushing the load, and I don't think that I should be pushing it with so few VMs. I suspect that I have some basic, incorrect configuration setting, but it's also possible that I have some giant misconceptions about virtualization. Any pointers? EDIT: Given the responses I've gotten so far, it seems that this is a measurement problem and not a configuration problem, making this less critical. Perhaps the real question is: How does the core utilization of the server reach a higher percentage than all individual cores' core utilization, and given that this possibility makes the metric useless for overall server load, what is the best global metric for measuring CPU load on hyper-threaded systems?

  Read the article

• Plesk wildcard subdomain not working

  - by avdgaag

  I'm trying to set up a wildcard subdomain on my VPS. Ultimately I want to end up with this: main site: my.domain.tld subdomain: sub1.my.domain.tld - should end up serving my.domain.tld/sub1 I am using plesk 8.6. I have created a DNS A record pointing at my VPS' IP. I have then restarted the DNS server and waited up to 24 hours. But trying ping sub1.my.domain.tld results in an unknown host error. So I know there's more stuff involved, configuring apache etc. But so far, I cannot even get the subdomain working at all, let alone serve up the right content. I have also tried a CNAME record, to no effect. I have also tried creating a regular subdomain with a fixed name, which also does not work. Pre-configured subdomains DO work, like ftp.my.domain.tld or mail.my.domain.tld. I am clearly missing something here, but my hosting provider charges a small fortune for any support request not involving hardware physically burning down, so I'm hesitant to ask them. Any ideas?

  Read the article

• Migrating from "partial" Exchange 2003 to full Exchange 2003 usability

  - by TheCleaner

  I have a client that is using Exchange 2003 on SBS 2003 R2, but only for calendar sharing and contacts sharing. Their email is still coming to their clients via a POP3 account on each client's Outlook. I'd like to move them over to using Exchange for both email and the other things they are utilizing it for now. Can you folks guide me in the right direction? The setup: external domain is akin to domain.com (and is where they get their POP3 email from now) internal domain is akin to domain.local only simple hardware firewall (no ISA) static external IP is available to use My "assumptions": Setup SMTP default connector in Exchange for their existing external domain Have their existing email backed up to PST files (just in case) Setup the new MX records to point domain.com to the static external IP I'm a little confused how I'm going to setup their existing Exchange accounts with the proper SMTP address though. Right now it is just [email protected]. Do I just need to modify or create a new recipient policy? Are there other steps involved that I'm missing? Anyone with a walkthrough or even a basic "steps" is fine. I'm fairly used to Exchange 03, but I've been on Exchange 07 for a while now so going back is the weird part...plus I don't know what issues Exchange 03 on SBS has versus the normal "version". Thanks for all the help!

  Read the article

• MAC addresses on dual-NIC mainboards

  - by Tom O'Connor

  Here's a weird problem. We've got a number of devices with dual-NIC mainboards. Some are Realtek NICs, which suck. Some are Intel e1000s, which don't. I've just noticed on 2 machines, one is an Intel NIC, one is a Realtek, that when I put the MAC address of one machine into the dhcpd.conf file on our DHCP server to get it to PXE boot the machine into a rebuild environment, initially everything is fine. The server gets a DHCP allocation, and PXE boots into the Ubuntu preseed enviroment. On one or two machines, it gets as far as Ubuntu's DHCP network configuration, and fails. If i pull up a busybox shell (on tty2 on the installing machine), and run ip link, I can see that the UP flag is set on the other NIC. Here's some stuff. host xeon16-ghz240-gb48-node1 { hardware ethernet BC:AE:C5:07:1F:18; filename "pxelinux.0"; next-server 192.168.123.80; } That's what's in dhcpd.conf This is what ip link on the evil machine looks like. Only one NIC is actually connected (deliberately). As you can see, the NIC that's in the dhcpd config, is not marked as UP, and the link that is UP, isn't the one in DHCP. So far I've seen this on two brands of dual-NIC configuration. Does anyone know 1) what's causing it, and b) What we can do about it?

  Read the article

• Is it possible to shrink the size of an HP Smart Array logical drive?

  - by ewwhite

  I know extension is quite possible using the hpacucli utility, but is there an easy way to reduce the size of an existing logical drive (not array)? The controller is a P410i in a ProLiant DL360 G6 server. I'd like to reduce logicaldrive 1 from 72GB to 40GB. => ctrl all show config detail Smart Array P410i in Slot 0 (Embedded) Bus Interface: PCI Slot: 0 Serial Number: 5001438006FD9A50 Cache Serial Number: PAAVP9VYFB8Y RAID 6 (ADG) Status: Disabled Controller Status: OK Chassis Slot: Hardware Revision: Rev C Firmware Version: 3.66 Rebuild Priority: Medium Expand Priority: Medium Surface Scan Delay: 3 secs Surface Scan Mode: Idle Queue Depth: Automatic Monitor and Performance Delay: 60 min Elevator Sort: Enabled Degraded Performance Optimization: Disabled Inconsistency Repair Policy: Disabled Wait for Cache Room: Disabled Surface Analysis Inconsistency Notification: Disabled Post Prompt Timeout: 15 secs Cache Board Present: True Cache Status: OK Accelerator Ratio: 25% Read / 75% Write Drive Write Cache: Enabled Total Cache Size: 512 MB No-Battery Write Cache: Disabled Cache Backup Power Source: Batteries Battery/Capacitor Count: 1 Battery/Capacitor Status: OK SATA NCQ Supported: True Array: A Interface Type: SAS Unused Space: 412476 MB Status: OK Logical Drive: 1 Size: 72.0 GB Fault Tolerance: RAID 1+0 Heads: 255 Sectors Per Track: 32 Cylinders: 18504 Strip Size: 256 KB Status: OK Array Accelerator: Enabled Unique Identifier: 600508B1001C132E4BBDFAA6DAD13DA3 Disk Name: /dev/cciss/c0d0 Mount Points: /boot 196 MB, / 12.0 GB, /usr 8.0 GB, /var 4.0 GB, /tmp 2.0 GB OS Status: LOCKED Logical Drive Label: AE438D6A5001438006FD9A50BE0A Mirror Group 0: physicaldrive 1I:1:1 (port 1I:box 1:bay 1, SAS, 146 GB, OK) physicaldrive 1I:1:2 (port 1I:box 1:bay 2, SAS, 146 GB, OK) Mirror Group 1: physicaldrive 1I:1:3 (port 1I:box 1:bay 3, SAS, 146 GB, OK) physicaldrive 1I:1:4 (port 1I:box 1:bay 4, SAS, 146 GB, OK) SEP (Vendor ID PMCSIERA, Model SRC 8x6G) 250 Device Number: 250 Firmware Version: RevC WWID: 5001438006FD9A5F Vendor ID: PMCSIERA Model: SRC 8x6G

  Read the article

• What is the best keyboard for typing speed (not layouts)

  - by Gapton

  So I am a programmer, and I like playing typing speed games. My typing speed is, for common English words, 85 to 90 wpm, max 95. I type on various devices, my laptop, desktop, office pc.... they all have slightly different keyboards. Being a curious programmer, I wonder what types of keyboard is used for the highest possible typing speed. Or let me phrase it in another way, what is the type of keyboards that people use in typing speed contest? Here is something I know that I feel like I can share: It must be a wired keyboard, I can feel the lag as I am typing this on my wireless keyboard, even if it is a slightly more expensive model which claims to have zero lag. I know people prefer a mechanical keyboard, for the hepatic feedback, however I have not tried one. It lasts longer and is noisy, it also does not have the problem of normal keyboards where you press many keys at a time the signals will get all jammed and the computer will only receive one or two keys. I personally prefer those "thin profile" keyboards. I type a lot, and 95 wpm put me in the top 5%, this is of course just on a gaming site. However when I type on the fat keyboards, my fingers have to travel a much longer distance before the keys actually click. This is where I find myself typing much faster with those thin profile keyboards found on my laptop. Because my fingers only hover on the keys and I only need to press a short distance, each stroke takes less force and light rapid strokes is what makes me type fast. When I type on a fat keyboard, I was forced to use heavy strokes, and this slows me down. There must be some people out there who are keyboard scientists, who actually do experiments and user tests with different setups. It would be interesting to understand more about the things we use everyday for not just work but a majority of our communications. P.S. this is about hardware and not about switching keyboard layouts to dvorak

  Read the article

• Windows XP SP3 Keyboard stops working

  - by Kevin K

  Here's the strangest thing I have yet to see in 20+ yrs of computer repairs. My in-laws Windowsx XP SP3 has stopped recognizing keyboards. The keyboards work fine in the BIOS, during the boot select process to boot normally, etc. but once Windows comes up it will not recognize any USB keyboard. The USB mouse works fine, have tried different USB ports, different keyboards, etc. nothing works. I can log into the machine via VNC and use the remote keyboard just fine, but not connected locally. Tried a system restore, it says nothing changed. I am about to just re-install Windows at this point, except I am afraid it will happen again. I have googled for this and it is not unheard of, but I have not found any solution other than nuking it. Anyone have any ideas? I have re-installed the USB drivers for the M/B. Gone into devices and deleted them for a re-install, etc. Keyboard works off a Linux live boot CD, and in the BIOS setup so it is not a hardware issue, and I have tried a few keyboards all of which I know are good and work fine on other systems.

  Read the article

• Router slowing my connection?

  - by Roberto

  I have a Linksys WRT54G and I pay for a 12Mbps connection. I've been testing my connection using speedtest.net for many days and always get 8Mbps. I called the support and they told me to bypass the router and test. I did it and got 16Mbps (much more than I pay for), so I thought "this guy just changed my speed so can he blame my router", and he blamed it. But to my surprise, everytime I bypass the router I get 16Mbps and when I use the router I get 8Mbps. Is this guy trolling me somehow (configuring the VOIP-modem-stuff to different profiles depending o the MAC address connecting to it) or is my router a POS? How can I find out? I don't know what's the thing the router connects to, it's a kind of VOIP adapter; the link is this one, but unfortunately I don't think you'll understand because it's in Portuguese. I know they can remotely connect to it, that's the origin of my conspiracy theory :) I just tested wired to the router and got 10Mbps (and still 8Mbps on wifi and 16Mbps without router) O_o I'm 5cm away from my router, so no obstacles to interfere, right? ------ UPDATE ------- It's a WRT54G V8, I'm using firmware v8.00.7 (will install 8.00.8 tomorrow, but I saw that it's only a minor fix to UPnP denial of service security vulnerability). Results: IPerf LAN-LAN: 80Mbps IPerf LAN-WLAN: 19Mbps (therefore we can ignore wireless issues/settings) I wasn't able to make the (W)LAN-WAN NAT-enabled test with IPerf, I get a connection refused error. I'm not sure if did it right: ran in server mode, configured router to forward that port to my IP and tried to connect to my internet IP that got from this site. I don't think there is a way to disable NAT using this firmware. Question: Let's suppose it's an underpowered hardware issue. Is it right to assume that custom firmwares could resolve the issue because they are possibly better implemented and would make better use of the router resources? I couldn't find any references pointing to wired performance improvements with the use of custom firmware.

  Read the article

• monitoring a /21 for potential bad guys with snort and port mirroring

  - by Adeodatus

  Hi all, I want/need to start monitoring our network a bit better. Its an odd network in that it comprises 2 /22 public IPs and a slew of private admin IPs. I do have one point in the network where it all comes together and I can turn on port mirroring on the catalyst. From that port, I'd like to turn up a box running various utilities. Snort is high on my list but it'd be nice to also get some networking statistics with something like Netflow. So, what are peoeple's thoughts. I can turn up a box needed for this with a bit of ease. We have the hardware available. What should I run? I'd love to know what kind of nasty things are potentially going on but I'd also like to see statistics on what people are doing on the network so I can better tweak our systems to handle it better and improve performance. I'm open so please, give me some ideas to go along with what I've got.

  Read the article

• Atlassian Crucible very slow on large repository

  - by Mitch Lindgren

  Hi everyone, My company has been running a trial of Atlassian Crucible for some months now. For repositories where it's working properly, users have given very positive feedback about the tool. The problem I'm having is that we have several different projects, each with its own repository, and some of those repositories are very large. One repository in particular has a large number of branches and probably around 9,000 files per branch. Browsing that repository in Crucible is extremely slow. Crucible is running on a CentOS VM. The VM has 4GB of RAM, and I've set Crucible's maximum at 3GB, of which it is currently using 2GB. I've brought this up in a support ticket with Atlassian, and they suggested the following: In particular because you have a rather large SVN repository you will likely find that Fisheye will be creating a large index file on disk. To help improve performance a few things you can try are: Increasing the available memory available to Fisheye (see the document above). Migrating to an external database: confluence.atlassian.com/display/FISHEYE/Migrating+to+an+External+Database Excluding files and directories from your index that aren't needed: confluence.atlassian.com/display/FISHEYE/Allow+(Process) (Sorry for not hyperlinking; don't have the rep.) I've tried all of these things to an extent, but so far none have helped greatly. I was originally running Crucible on a Windows box with 2GB of RAM using the built in HSQL DB. Moving to MySQL on CentOS saw a performance increase for some repositories, and made Crucible much more stable, but did not seem to help much with our biggest repository. There are only so many files/branches I can exclude from indexing while maintaining the tool's usefulness. That being the case, does anyone have any tips on how to speed up Crucible on large repositories, without investing in insanely powerful hardware? Thanks! Edit: To clarify, since I didn't mention it explicitly above, I am using FishEye.

  Read the article

• How do I fix this Windows 7 wireless connectivity issue?

  - by Charles Randall

  I have a laptop with an Intel Wireless Centrino 6300 module. Recently, the machine has stopped properly connecting to my wireless router. It will get stuck in a loop of connecting, then disconnecting and reconnecting. While connected, it will simply say "No Internet Access." Running inSSIDer 2.0, it shows my network jumping around between two channels -- I know this isn't the case, because I've set my router to sit on one single channel. My MacBook Pro, Boxee Box, PS3, and Xbox 360 all connect fine to the wireless and have no problems at all. I know it's not the wireless module, as I bought a second one recently assuming the first had died -- but I get the same behavior with both. Sometimes, I can fix the issue temporarily by deleting the network (Using the Manage Wireless Networks page), and then re-adding it (via standard wireless methods). Then it will work for a few days. But inevitably the problem comes back, and now the laptop simply won't connect to the wireless at all, even if I take steps that usually work. Since I've ruled out the hardware, and it's unlikely some kind of interference issue (because I would expect to see it on any multitude of other devices), I would think at this point that it's a problem with Windows itself. One thing that might be a hint, even though I delete the network, when I add it again, it's always listed as "Wireless Network Connection 2" even though there isn't another in the list.

  Read the article

• Multiple vlans access to shared pbx system

  - by Matt

  I'm new to networking and was looking for some assistance. First off I'm using packet tracer to diagram my scenario as I will be receiving my equipment next week to deploy. Hardware to be used: 2 catalyst 3560 switches all connect to a sonic wall router I have two companies that work in the same office space. I need to keep these companies separate on their own vlan. They will however need to share the phone system. (Packet tracer file uploaded to give those who have the time to see what I put together.) http://dl.dropbox.com/u/86234623/network%20build.pkt Here is my current test scenario: on switch 0 I have: company A on vlan 2 computers 172.16.1.100 and 101 255.255.0.0 FA0/10 FA0/11 company B on vlan 3 computers 172.16.2.102, 255.255.0.0 FA0/12 PBX on a trunk port 172.16.0.5, 255.255.0.0 FA0/5 trunk port on FA0/1 to connect the switches on switch 1 I have: company A on vlan 2 computers 172.16.1.102, 255.255.0.0 company B on vlan 3 computers 172.16.2.100 and 101, 255.255.0.0 trunk port on FA0/1 to connect the switches I can ping the respective computers on the same vlan but cant ping company A to B which is what I want. However neither company can talk (ping) the PBX. Here are the commands I used to configure what I have: switch 0 en conf t vlan 2 name A vlan 3 name B int fa0/10 switchport mode access switchport access vlan 2 int fa0/11 switchport mode access switchport access vlan 2 int fa0/12 switchport mode access switchport access vlan 3 int fa0/5 switchport trunk encapsulation dot1q switchport mode trunk switchport trunk allowed vlan 1-3 int fa0/1 (to connect the switches) switchport trunk encapsulation dot1q switchport mode trunk switchport trunk allowed vlan 1-3 Switch 1 en conf t vlan 2 name A vlan 3 name B int fa0/10 switchport mode access switchport access vlan 3 int fa0/11 switchport mode access switchport access vlan 3 int fa0/12 switchport mode access switchport access vlan 2 int fa0/1 (to connect the switches) switchport trunk encapsulation dot1q switchport mode trunk switchport trunk allowed vlan 1-3

  Read the article

• On a dual-GPU laptop, is using the discrete GPU ever more power efficient?

  - by Mahmoud Al-Qudsi

  Given a laptop with a dual integrated/discrete GPU configuration, is it ever more power efficient to use the discrete GPU instead of the integrated? Obviously when writing an email or working on a spreadsheet, the integrated GPU will always use less power. But let's say you're doing something graphics-medium but not graphics-intensive/heavy - is there a point where it actually makes sense to fire up the discrete GPU, not for performance but for power-saving reasons? Off the top of my head, I can think of a scenario where the external GPU supports hardware decoding of a particular video codec - I'd imagine there is a "price point" where using the GPU saves more energy than decoding that fully in software would. But I think most GPUs, integrated or discrete, pretty much decode just the plain-Jane h264. But maybe there is something more complicated, perhaps if you're doing something like desktop/windowing animations or a flash animation on a website (not an embedded flash video) - maybe the discrete GPU will use enough less power to make up for switching to it? I guess this question can be summed up as to whether or not you can say beyond doubt that if you don't care for performance on a laptop with two GPUs, always use the integrated GPU for maximum battery life.

  Read the article

• Openpgp does not work in my Thunderbird-Installation

  - by zerozero

  Hello community, as mentioned above - i encountered serious troubles. here are the versions of the related software: SuSE 11.2, Thunderbird v.3.1.6, released October 27, 2010, Firefox 3.6 v3.6.12 I created an installations with an own partition both for the user and for the TB-Mails. For a new installation on another hardware i took these partitions. When i wanted to read the emails, i got an error-message like this: The GPG-agent for your GnuPG-version 2.0.12 couldn´t get started Further i got an error message for the access on services of enigmail. The file jar:file:///usr/lib/mozilla/extensions/{3550f703-e582-4d05-9a08-453d09bdfdc6}/{847b3a00-7ab1-11d4-8f02-006008948af5}/chrome/enigmail.jar!/locale/de-DE/enigmail/help/initError.html couldn´t get found. I found out, that this path doesn´t come from TB nor from firefox, but from enigmail. I installed several (un-)pack-programs. the only effect was, that in the menu of TB the entry for OpenPGP appeared in the TB-Menu. The errors as described above repeat at every try to read an email. I deleted and re-installed enigmail, but the errors dont´t disappear. What can i do to get rid these error-messages ? Thanks in advance

  Read the article

• Server Performance

  - by sb12

  I know very little about performance tuning of servers etc... so i thought i'd put this up here as i start some research on it, just to get some direction. I am in the process of migrating from my old server to a new one - both are 64 bit machines. One is a few years old, the other brand new (PowerEdge R410). The old server spec is: 2 cpus, 3.4GHz Pentiums, 8G of RAM, Fedora 11 currently installed The new server spec is: 16 cpus, 3.2 GHz Xeon, 16G of RAM, CentOS 6.2 installed. Also RAID10 is on the new server - no RAID on the old one. Both servers currently have the same database (MySQL) with the same data migrated. I wrote a Perl script that simply steps through each row of a table in the database (about 18000 rows) and updates a value in that row. Every row in the table is updated. Out of curiosity i ran this perl script on both machines, just to see how the new server would perform vs. the old one, and it produced interesting results: The old server was twice as fast as the new one to complete. Looking at the database, both are configured exactly the same (the new one being a dump of the old one...)... Anyone any ideas why this would be given the hardware gap between both? As i said i'm about to start some digging, but thought i'd put this up here to maybe get some good direction.... Many thanks in advance..

  Read the article

• pfsense 2.0.1 Firewall SMB Share not showing up under network

  - by atrueresistance

  I have a freenas NAS with a SMB share running at 192.168.2.2 of a 192.168.2.0/28 network. Gateway is 192.168.2.1. Originally this was running on a switch with my LAN, but now having upgraded to new hardware the Freenas has it's own port on the firewall. Before the switch the freenas would show up under Network on a windows 7 box and an OSX Lion box as freenas{wins} or CIFS shares on freenas{osx} so I know it doesn't have anything do to with the freenas. Here are my pfsense rules. ID Proto Source Port Destination Port Gateway Queue Schedule Description PASS TCP FREENAS net * LAN net 139 (NetBIOS-SSN) * none cifs lan passthrough PASS TCP FREENAS net * LAN net 389 (LDAP) * none cifs lan passthrough PASS TCP FREENAS net * LAN net 445 (MS DS) * none cifs lan passthrough PASS UDP FREENAS net * LAN net 137 (NetBIOS-NS) * none cifs lan passthrough PASS UDP FREENAS net * LAN net 138 (NetBIOS-DGM) * none cifs lan passthrough BLOCK * FREENAS net * LAN net * * none BLOCK * FREENAS net * OPTZONE net * * none BLOCK * FREENAS net * 192.168.2.1 * * none PASS * FREENAS net * * * * none BLOCK * * * * * * none I can connect if I use \\192.168.2.2 and enter the correct login details. I would just like this to show up on the network. Nothing in the log seems to be blocked when I filter by 192.168.2.2. What port am I missing for SMB to show up under the network and not have to connect by IP? ps. Do I really need the LDAP rule?

  Read the article

• Can I change the user id of a user on one Linux server to match another server in /etc/passwd?

  - by user76177

  I have a Rails application that is on a virtual machine (RHEL 6) and it's database is on dedicated hardware (also RHEL 6). The app server has an NFS directory from the db server mounted and accessible. It needs to write images to that server that are uploaded via the app. Background processes on the db server need to read and write to the same directory, as they perform resizing operations on the uploaded files. Right now none of this is working, because the user ids are different between the two systems. I only need this to work for this one application, so it is way too much overhead to put an LDAP system in place. Can I simply change the user id of this one user in one of the systems, or will that cause mass chaos? UPDATE: The fix worked, at least on local devices. Unfortunately the device I have mounted to the main db server still thinks my user id is 502 instead of 506. Do I need to remount that device, or is there an NFS daemon I can stop and restart to refresh it?

  Read the article

• Changing externally visible IP on a multi-IP router?

  - by AlternateZ

  I work at a public library and I'm trying to configure OCLC's EzProxy software. I've run into a problem and I think it's related to our network config. I'm punching above my weight here a little so I need some help. I think I'm trying to configure a 1:1 NAT, but not sure how or if our hardware supports it. The EzProxy machine is on an internet line which supports multiple external IPs. Our router is a Billion BiGuard30. There's another server on this line, let's say its IP is x.x.x.9. The EzProxy machine is x.x.x.11 I've set up port forwarding from x.x.x.11 on the http ports to the EzProxy machine. Trying to browse to x.x.x.11 from an external PC works fine - we get to the EzProxy page we are serving. However, if we go to something like WhatIsMyIP from the EzProxy machine, it says that its IP is x.x.x.9. This causes problems with our user authentication software. How do we make the rest of the internet see that the machine is x.x.x.11? There doesnt seem to be any "outbound port forwarding" on the Billion router, nor is there any "1:1 NAT" options in its config webpage. The EzProxy machine is running Ubuntu 12.04, if that helps.

  Read the article

• Word documents very slow to open over network, but fine when opened locally - on one machine

  - by Craig H

  Windows XP, Word 2003, patched. The issue is happening with several Word documents stored on a network drive. The Word documents are clearly a bit wonky (i.e. one is 675k, but if you copy everything but the last paragraph marker into a new document, the new document is only 30k). But that's only part of the problem. On one weird machine, and one machine only, it takes ~20 seconds to open these Word documents from the network drive. Copy the file to C: on that werid machine? Opens immediately. Go to other machines (that are very similar - same patch level, etc.) and open the same document from the network? Opens immediately. Delete normal.dot? 20 seconds. Login with a different user on the weird machine? 20 seconds. Plug wonky machine into a different network port? 20 seconds. So the problem appears to be hardware related (i.e. wonky internal NIC) or related to a setting that is not profile specific. Any ideas? "Scrubbing" all the documents isn't ideal for several reasons. This is driving me nuts because I swear I ran into this before many years ago and eventually figured it out. But I appear to have lost my notes.

  Read the article

• Not recognizing second monitor after hibernate (Windows 7, Dell D630 laptop)

  - by Brooks Moses

  I have a Dell Latitude D630 laptop which I've recently updated to Windows 7 64-bit. (The Dell site confirms that it's Windows-7-compatible.) Normally it lives in a docking station with a second monitor connected to the DVI port on the docking station, and I use the second monitor in a multi-monitor configuration with the laptop screen. Sometimes I undock the laptop and use it separately. Here's the problem: If I hibernate the laptop while undocked, and then power it back up in the docking station, it does not recognize the second monitor. By which I mean that not only does it not share the desktop onto the second monitor, but if I go into the control panel for display settings and press "Detect", it does not even detect the existence of the second monitor. I can tell it to "use the VGA port anyway" for a second monitor, but the monitor is connected to a DVI port on the docking station, so that doesn't do anything useful. If I entirely reboot the laptop while it's connected to the docking station, it has no problem recognizing the second monitor and using it. But then, if I hibernate, undock, de-hibernate while undocked and rehibernate, and then re-dock and de-hibernate, it's back to not recognizing the second monitor again. I'm reasonably certain that this is not a limitation of the hardware; this worked fine on Windows XP. I'm currently using the Windows 7 driver for my video card. I attempted to use the video driver from the Dell website for this laptop, but Dell only provides Vista 64-bit drivers, not Windows 7 64-bit drivers. Their "Windows 7 compatibility" page suggests that the Vista drivers should work, but when I attempted to install the driver, it gave me a "this operating system not supported" error and refused to install. Any further ideas?

  Read the article

• Can't remotely connect through SQL Server Management Studio

  - by FAtBalloon

  I have setup a SQL Server 2008 Express instance on a dedicated Windows 2008 Server hosted by 1and1.com. I cannot connect remotely to the server through management studio. I have taken the following steps below and am beyond any further ideas. I have researched the site and cannot figure anything else out so please forgive me if I missed something obvious, but I'm going crazy. Here's the lowdown. The SQL Server instance is running and works perfectly when working locally. In SQL Server Management Studio, I have checked the box "Allow Remote Connections to this Server" I have removed any external hardware firewall settings from the 1and1 admin panel Windows firewall on the server has been disabled, but just for kicks I added an inbound rule that allows for all connections on port 1433. In SQL Native Client configuration, TCP/IP is enabled. I also made sure the "IP1" with the server's IP address had a 0 for dynamic port, but I deleted it and added 1433 in the regular TCP Port field. I also set the "IPALL" TCP Port to 1433. In SQL Native Client configuration, SQL Server Browser is also running and I also tried adding an ALIAS in the I restarted SQL server after I set this value. Doing a "netstat -ano" on the server machine returns a TCP 0.0.0.0:1433 LISTENING UDP 0.0.0.0:1434 LISTENING I do a port scan from my local computer and it says that the port is FILTERED instead of LISTENING. I also tried to connect from Management studio on my local machine and it is throwing a connection error. Tried the following server names with SQL Server and Windows Authentication marked in the database security. ipaddress\SQLEXPRESS,1433 ipaddress\SQLEXPRESS ipaddress ipaddress,1433 tcp:ipaddress\SQLEXPRESS tcp:ipaddress\SQLEXPRESS,1433

  Read the article

• Migrate Windows Server 2008 to a new hard disk 2

  - by MainMa

  Hi, A few weeks ago, I already asked how to move a Windows Server 2008 to a new hard disk. Despite the previous answers and two weeks lost trying to do it, I am always unable to move the OS to the new drive. What I tried: A backup/restore using Windows Backup. This never helped. First, I tried to backup, then copy the backup to a new drive, then restore. This results in "The parameter is incorrect. (0x80070057)" error caused by a bug in Windows Backup. Recently, I attempted to backup to a network share, but I can't restore from it, because of a "*The network path was not found. (0x80070035)" error. Trying the netsh interface ipv4 set address [...] does not work neither (saw at least three different errors, mostly "The interface is unknown.") A previously suggested solution using imagex from Windows AIK results in a non-bootable disk after writing an image to it. When booting from Windows 2008 installation disk (from USB), it finds that the HDD is not bootable and proposes to fix this, but then crashes, resulting in an unbootable USB flash disk (and HDD stays unbootable). As I said in my previous question, doing a clone of a hard disk drive gives an (of course) bootable disk, but Windows complain about hardware changes and cannot start. Now can somebody suggest me another way to move Windows Server 2008 to a new hard disk? Is it at least possible to do, or any hard disk failure/change implements necessarily to reinstall the whole OS?

  Read the article

• Mac Management and Security

  - by Bart Silverstrim

  I was going through some literature on managing OS X laptops and asked someone some questions about usage scenarios when using the MacBooks. I asked someone more knowledgeable than I about whether it was possible for my Mac to be taken over if I were visiting another site for a conference or if I went on a wifi network at a local coffee house with policies from an OS X Server with workgroup manager (either legit for the site or someone running a version of OS X Server on hardware they have hidden somewhere on the network), which apparently could be set up to do things like limit my access to Finder or impose other neat whiz-bang management features. He said that it is indeed possible for it to happen as it would be assigned via the DHCP server and the OS X server would assume my Mac is a guest and could hand out restrictions and apparently my Mac will happily accept them without notifying me or giving me an option, unlike Windows which I believe would need to be joined to a domain before it becomes "managed" by Active Directory. So my question is as network admins and sysadmins with users traveling with MacBooks, is there a way to reasonably protect your users from having their machines hijacked without resorting to just turning off networking all the time? Or isn't this much of a security hazard? What threat does this pose to the road warriors in your businesses?

  Read the article

• Cursor lag when mouse cursor changes?

  - by Mathias Lykkegaard Lorenzen

  Cursor lag issue Introduction I'm experiencing a newly arrived problem lately that frustrates me a lot. The computer I bought is a Clevo 150ERM. Two of my friends bought the same machine, and are experiencing the same issue. The computer came with Windows 7. There, I had no issues. Then, when we all switched to Windows 8, they had the mouse problem and I didn't. That is until after 4 or 5 months when I decided to install the RTM driver of my Intel graphics chip, and the latest Nvidia driver. I also installed the latest version of Skype that just released (Skype 6 and Skype for Metro). This basically leads me to conclude that the issue is not hardware-prone, and is not based on the operating system itself, rather the drivers or components that follow with it. Description of the issue The issue itself (lag with the mouse) happens whenever the cursor icon changes. For instance, if I keep hovering from and to a textfield (and the cursor changes into a caret and then back to a mouse), it stops for 200 milliseconds while it changes the icon. An example is if I follow the mouse in the pattern shown by the arrows below. When crossing the window border, the cursor changes into a "resize window" cursor for a short while, making the cursor lag. This doesn't sound like much, but it happens every time the cursor changes (even if it's to just move the mouse somewhere else, and accidentally make it cross a window border from where the resize cursor shows etc). What do you suggest I try?

  Read the article

< Previous Page | 271 272 273 274 275 276 277 278 279 280 281 282  | Next Page >