Search Results

Search found 27336 results on 1094 pages for 'network state'.

Page 282/1094 | < Previous Page | 278 279 280 281 282 283 284 285 286 287 288 289  | Next Page >

  • ip routing policy in linux

    - by Dragos
    I have a linux system with two network interfaces (eth0 in x.x.x.0 and eth1 in x.x.y.0). Is there any posibility to add some route policy to send all the traffic to network x.x.y.0. I would like even the traffic from eth0 to be send to eth1's network. I cannot delete the direct connected networks from the routing table so all the traffic from x.x.x.0 network is send to eth0. I would like to send all traffic to eth1.

    Read the article

  • MPLS basic configuration

    - by Vineet Menon
    I want to test out MPLS VPN in my lab. I have 3 routers. 2 PEs and 1P router, all cisco 2921. Something like this, ----- ---- ----- | PE1 |.1____192.168.1.0____.2| P |.2____192.168.2.0____.1| PE2 | | | | | | | ----- ---- ----- lo0:10.1.1.1 lo0:10.1.1.2 lo0:10.1.1.3 Here's the configuration file for each of them, PE1 router hostname PE1 ! no ipv6 cef ip source-route ip cef ! ! ! ip vrf cust1 rd 100:100 route-target export 100:100 route-target import 100:100 ! ! interface Loopback0 ip address 10.1.1.1 255.255.255.255 ! interface GigabitEthernet0/0 ip address 192.168.1.1 255.255.255.0 duplex auto speed auto ! interface GigabitEthernet0/1 ip vrf forwarding cust1 ip address 172.16.1.1 255.255.255.0 duplex auto speed auto ! router ospf 1 network 10.1.1.1 0.0.0.0 area 0 network 192.168.1.0 0.0.0.255 area 0 ! router bgp 100 bgp log-neighbor-changes neighbor 10.1.1.3 remote-as 100 neighbor 10.1.1.3 update-source Loopback0 neighbor 172.16.1.2 remote-as 65001 ! address-family vpnv4 neighbor 10.1.1.3 activate neighbor 10.1.1.3 send-community extended exit-address-family For P router: hostname P ! no ipv6 cef ip source-route ip cef ! interface Loopback0 ip address 10.1.1.2 255.255.255.255 ! interface GigabitEthernet0/1 ip address 192.168.1.2 255.255.255.0 duplex auto speed auto ! interface GigabitEthernet0/2 ip address 192.168.2.2 255.255.255.0 duplex auto speed auto ! router ospf 1 network 10.1.1.2 0.0.0.0 area 0 network 192.168.1.0 0.0.0.255 area 0 network 192.168.2.0 0.0.0.255 area 0 ! For PE2 router: ! hostname PE2 ! no ipv6 cef ip source-route ip cef ! ! ! ip vrf cust1 rd 100:100 route-target export 100:100 route-target import 100:100 ! ! ! interface Loopback0 ip address 10.1.1.3 255.255.255.0 ! interface GigabitEthernet0/0 ip address 192.168.2.1 255.255.255.0 duplex auto speed auto ! interface GigabitEthernet0/1 ip vrf forwarding cust1 ip address 172.16.2.1 255.255.255.0 duplex auto speed auto ! router ospf 1 network 10.1.1.3 0.0.0.0 area 0 network 192.168.2.0 0.0.0.255 area 0 ! router bgp 100 bgp log-neighbor-changes neighbor 10.1.1.1 remote-as 100 neighbor 10.1.1.1 update-source Loopback0 neighbor 172.16.2.2 remote-as 65001 ! address-family vpnv4 neighbor 10.1.1.1 activate neighbor 10.1.1.1 send-community extended exit-address-family ! I am following this article form cisco. But things are not working properly. Any help would be appreciated.

    Read the article

  • Why is my iPhone WIFI so slow at home?

    - by John Fouhy
    When my iPhone is connected to my home wireless network, the internet is unusably slow. I installed the speedtest.net application; here are some results from tonight: Down: 0.0kB/s, Up: 0.0kB/s, ping: 2230ms Down: 2.5kB/s, Up: 40.5kB/s, ping: 2182ms Down: 0.0kB/s, Up: 20.0kB/s, ping: 197ms For comparison, here is the result from my iMac to the same server, which is on the same wireless network (and has no wired connection): Down: 139kB/s, Up: 53.8kB/s, ping: 182ms Neither my iMac nor the Dell laptop also on the network have experienced the wifi problems I get with my iPhone. On the other hand, I tried browsing a website on the wireless network at work with no problems. EDIT: SpeedTest at work gives me 156kB/s down. EDIT2: Girlfriend (owner of the Dell) reports actually the internet is sometimes very slow. Perhaps there is more going on. No problems with my iMac. My router is a ASUS WL-500g Premium V2 running OpenWrt Kamikaze with X-Wrt Extensions 8.09.

    Read the article

  • Local IP address same as Google's external

    - by GRIGORE-TURBODISEL
    I'm exampling Google's IPs, but you get the idea. What happens if somebody configures a router's LAN address pool to range from 62.231.75.2 to 62.231.75.255, then his computer's IP address to 62.231.75.232 and someone else on the network tries to access Google? Or better off, is there any case in which someone in that network can, by merely attempting to access Google, accidentally bump into another computer on the network?

    Read the article

  • Multicasting Windows 7 Image

    - by LawnChairSkank
    I am trying to deploy some new machines with windows 7 for the first time in our computer labs. We used to use third party imaging software and then run sysprep after the image was copied(XP), but it seems you can't go that route with windows 7. We set up a new imaging server with the windows system image manager, but when we try to multicast the image it pretty much takes down our whole staff and faculty network. I heard you can turn on a multicast feature on our cisco switches to help with the issue, but that it also slows the switches to a crawl. Another idea we have tried was pulling the the computer lab switch off the main network and plugging the imaging server directly into the computer lab switch so the multicast doesn't take down our network, but it doesn't seem to work without being able to hit a domain controller. Is there a way to multicast without taking out the network? I feel like I am missing something... Thanks in advance

    Read the article

  • Possible Solution for Setting up a Linux VPN Server to Encrypt WLAN Traffic of Macs and iPhones on

    - by GorillaPatch
    I would like to set up a VPN server on debian linux to encrypt wireless traffic coming from my Mac or iOS device. I would like to use a certificate-based solution. Setting up a PKI infrastructure and managing certificates is OK for me. 1. Which server to pick? By looking through the internet and here on stackoverflow I found the following possible solutions: strongSwan IPSec and racoon Which solution is feasible for a linode running debian squeeze? 2. How to configure the network? If I understood correctly a VPN has a virtual network interface as an endpoint on the server side. Naively I would think that I need a DHCP server running on the server to assign a dynamic private IP (like of the class C network 192.168.xxx.xxx) to the connecting clients. Next I think I would need to set up masquerading to NAT the incoming VPN traffic to the real interface directly connected to the internet. Is this the right way to go? Do you have any configuration examples? I often saw VPN configurations used to connect to your home network, but that is not what I am looking for. I have a server up in the internet and want to use it as a proxy to encrypt traffic in insecure network environments like public WLANs.

    Read the article

  • Protect Windows VPN from Unauthorized Users

    - by kobaltz
    I have a VPN connection that I use while away from home to remote into my home network. I would use a zero config solution like Hamachi, but need access from my mobile device. Therefore, I have my Windows Home Server acting as the VPN server and will accept incoming connections. Both the username and password are strong. However, I'm worried about brute force attacks against my network. Is there something else that I should do to protect my network from having unauthorized access attempts to my network? I'm familiar with Linux's FAIL2BAN, but wasn't sure if something similar existing for Windows.

    Read the article

  • zfs raidz1-0 corrupted data, all disks are online

    - by gkcr2d2
    My zfs pool "datas" is unavailable but all my disks are online. Do you know how the problem can be fixed? root@oxygen:~# zpool status pool: datas state: UNAVAIL scan: none requested config: NAME STATE READ WRITE CKSUM datas UNAVAIL 0 0 0 insufficient replicas raidz1-0 UNAVAIL 0 0 0 corrupted data scsi-SATA_ST3000DM001-9YN_W1F0LBVX ONLINE 0 0 0 scsi-SATA_ST3000DM001-9YN_W1F0KYX9 ONLINE 0 0 0 scsi-SATA_ST3000DM001-9YN_W1F0LCC8 ONLINE 0 0 0 scsi-SATA_ST3000DM001-9YN_W1F0LBXZ ONLINE 0 0 0

    Read the article

  • zfs raidz1-0 corrupted data, all disk are online

    - by gkcr2d2
    my zfs pool "datas" is unavailable but all my disk are online, Do you know how the problem can be fixed? Thank you for your help. root@oxygen:~# zpool status pool: datas state: UNAVAIL scan: none requested config: NAME STATE READ WRITE CKSUM datas UNAVAIL 0 0 0 insufficient replicas raidz1-0 UNAVAIL 0 0 0 corrupted data scsi-SATA_ST3000DM001-9YN_W1F0LBVX ONLINE 0 0 0 scsi-SATA_ST3000DM001-9YN_W1F0KYX9 ONLINE 0 0 0 scsi-SATA_ST3000DM001-9YN_W1F0LCC8 ONLINE 0 0 0 scsi-SATA_ST3000DM001-9YN_W1F0LBXZ ONLINE 0 0 0

    Read the article

  • having 2 ip's on a debian 7 box

    - by David
    I just installed Debian Wheezy on my homeserver. I want to assign 2 ip's to it on the same network interface, 1 static ip (eth0) and 1 dynamic ip (eth0:1). I know it doesn't make much sense but I need it to test something. I edited my /etc/network/interfaces to be like this: auto lo eth0 eth0:1 iface lo inet loopback iface eth0 inet static address 192.168.178.240 network 192.168.178.0 netmask 255.255.255.0 broadcast 192.168.178.255 gateway 192.168.178.1 iface eth0:1 inet dhcp when I bring up eth0:1 (ifup eth0:1) I get the following error (eth0 works fine) Bind socket to interface: No such device Failed to bring up eth0:1. is it even possible to have a dynamic and static ip on the same network adapter?

    Read the article

  • How can I configure the embedded wireless card in a Toshiba Satellite Pro 4600 to work under Lubuntu 10.10?

    - by MoLE
    I'm struggling to get the embedded wireless card in this laptop to work. In 7.10 (gutsy) it worked fine. Now I'm trying to get 10.10 (maverick) working on it, and am using the Lubuntu flavour due to the low resources of this laptop. The hardware: Appears to be an embedded pcmcia card. pccardctl ident gives: Socket 0: product info: "TOSHIBA", "Wireless LAN Card", "Version 01.01", "" manfid: 0x0156, 0x0002 function: 6 (network) The default kernel recognises the card and loads the orinoco_cs driver. orinoco_cs 0.0: Hardware identity 0005:0002:0001:0002 orinoco_cs 0.0: Station identity 001f:0001:0006:000e orinoco_cs 0.0: Firmware determined as Lucent/Agere 6.14 Then for some reason, the driver isn't happy with this and gives: orinoco_cs 0.0: Hardware identity 0005:0002:0001:0002 orinoco_cs 0.0: Station identity 001f:0002:0009:0030 orinoco_cs 0.0: Firmware determined as Lucent/Agere 9.48 All seems ok until I try to associate with my access point using Network Manager. eth1: Lucent/Agere firmware doesn't support manual roaming repeated about 10 times then NM gives up. According to the linuxwireless.org wiki page on this driver, this is a known issue, and I quote: Known issues Roaming and WPA_supplicant Lucent/Agere firmware doesn't support manual roaming On the Agere cards, roaming is controlled by the firmware instead of userspace. You will get the above message if userspace attempts to associate with a specific AP rather than by SSID. If you are using wpa_supplicant use ap_scan=2 mode. NetworkManager uses wpa_supplicant, so the above also applies. At this point my google-fu has failed me, and I can't find how to configure network manager to use the mystical "ap_scan=2" mode via wpa_supplicant. I have tried the following suggested solutions (from launchpad or the forums) deleting the agere* files from /lib/firmware using wicd instead of network manager combining both blacklisting the orinoco_cs driver in an attempt to force use of the hostap_cs driver instead (in case it is a prism2 card). Obviously none of them have worked for me. Any hints on how to perform the suggested workaround above? Edit: I have also confirmed working on 8.10 (intrepid) live CD.

    Read the article

  • How can I join two simple home networks together using an ethernet cable?

    - by Ilia Jerebtsov
    I want to join two different home networks together like so: PC A1 PC A2 PC B1 PC B2 \ / \ / Gateway A <----- ethr. cable -----> Gateway B | | ADSL modem A ADSL modem B Both networks are of the basic residential type with identical configuration, with all PCs running Vista/7. The point is to temporarily join two apartments in a building for gaming and file sharing, and the holy grail would be: PCs on network A can access PCs on network B and vice-versa (file shares and gaming). Each network uses its own internet connection. Data between networks shouldn't take a trip through the internet (broadband upload speeds are severely capped) A network's internet access should continue working if the joining cable is disconnected with minimal configuration changes. How closely can this be achieved?

    Read the article

  • Windows 2003 Server Intermittent DNS Issues

    - by Mike
    Looking for a little help here. I have a Windows 2003 DNS Server set up on our network. Lately computers on our LAN have been, at times, unable to resolve a certain sub domain for our website whereas other times the request is resolved just fine. During these periods of "downtime" all other network activity (i.e web sites, internal resolutions, network shares, etc.) remains normal. I can tell it is a problem with our DNS server because the resolution always works from outside our network. I'm hoping someone out there has experienced something similar or could at least offer me place to start troubleshooting. Thanks!

    Read the article

  • How do I setup a Gnome 3.2 VPN connection (Fedora 16)

    - by mpeters
    I just switched to Gnome 3 on a new laptop to try it out. Lots of things are different, but I think I can get used to them. But I'm having a real problem trying to figure out how to get the new network manager to setup a VPN through the GUI. I have openvpn, NetworkManager and NetworkManager-openvpn installed, but when I click on the network icon in gnome-shell there is nothing about vpn connections in there. When I click the "Network Settings" link in that menu I just see menus for Wired, Wireless and Network Proxy and none of those screens has anything for VPN connections either. Any suggestions about where I need to look to setup my connections and how to make it easier connect when I need to?

    Read the article

  • Router intermittently failing

    - by nomen
    My old Asus router died a few weeks ago, so I thought I'd set up my Debian box to deal with routing my home network. I have a few complications, but I adapted my configuration from a previously working configuration, and I don't see why I am having intermittent problems. But I am having them! Every so often, my SSH connections to the router (and to the Xen virtual machines hosted by the router) just drop. I am unable to use the router's dns server. I can't ping the router. Etc. All of these things work most of the time, but break down intermittently, for a few minutes at a time. (I can provide more details, but I'm not sure what will be helpful) /etc/network/interfaces: # The loopback network interface auto lo iface lo inet loopback # Gigabit ethernet, internal network auto eth0 allow-hotplug eth0 iface eth0 inet manual # USB ethernet, internet auto eth1 allow-hotplug eth1 iface eth1 inet dhcp # Xen Bridge auto xlan0 iface xlan0 inet static bridge_ports eth0 address 10.47.94.1 netmask 255.255.255.0 As I understand it, this is sufficient to create the network interfaces, and even do some switching between Xen hosts and my eth0 interface. I installed and configured Shorewall to manage routing between the bridge and my internet-facing interface: /etc/shorewall/zones fw firewall net ipv4 lan ipv4 /etc/shorewall/interfaces net eth1 detect dhcp,tcpflags,nosmurfs,routefilter,logmartians lan xlan0 detect dhcp,tcpflags,nosmurfs,routefilter,logmartians,routeback,bridge /etc/shorewall/policy net all DROP info fw net ACCEPT info all all REJECT info /etc/shorewall/rules DNS(ACCEPT) fw net DNS(ACCEPT) lan fw Ping(ACCEPT) lan fw ... and so on, these all work, when the router is accepting traffic at all. /etc/shorewall/masq eth1 10.47.94.0/24 Also, the router is currently "working", and I checked on a problematic client: arp infrastructure infrastructure.mydomain (10.47.94.1) at 0:23:54:bb:7d:ce on en0 ifscope [ethernet] I tried it when the router was down, and I (eventually) got the same response. It took about 30 seconds to return, though.

    Read the article

  • Remote access to a KVM Ubuntu virtual server

    - by Lee
    I've just setup an ubuntu virtual server and everything seems to be working fine. I used KVM to get it working with a bridged network. I've given the virtual server a static ip address on my network. I don't seem to be able to connect to the virtual machine though from outside my network. If I'm on my own network it all works fine, I can ping the ip and connect to it. The virtual server can ping other machines and sites on the internet. I changed the port forwarding rules on my router to forward any connections on a specific port to the virtual server ip address thinking that was the problem, but it was still the same. Is there something I'm missing here which is blocking outside connections to the virtual machine? Thanks.

    Read the article

  • Ubuntu Server 12.04 as a router. Problem with DNS?? Or Routing table?

    - by Lorenzo
    I have a virtualbox lab made up of 4 Windows 2008 R2 servers (DC/DNS,SQL,SHAREPOINT, EXCHANGE) that are configured with static ip addresses with NIC's attached to Internal network. Everything works. I had the requirement to execute some tests that also access external services available on the internet. To keep things clean and similar to the production environment I have installed another VM, with Ubuntu Server 12.04 64 bit and configured (I hope) to work as a router like described on this post. This VM has two network interfaces: first is Bridged with the host and is used as a WAN connection and the other one attached in the Internal Network with its own static IP address on the internal network subnet. But actually the Windows servers does not connect to the internet while the unix one connects. I did a route command. this is the result: Kernel IP Routing table Destination Gateway Genmask Flags Metric Ref Use Iface default 10.69.121.1 0.0.0.0 UG 100 0 0 eth0 10.69.121.0 * 255.255.255.0 U 0 0 0 eth0 192.168.83.0 * 255.255.255.0 U 0 0 0 eth1 Can somebody help me with this configuration? :) Thanks! Addendum: I forgot to mention that one of the windows server hosts a DNS service for which I should maybe configure a forwarding server but I do not exactly know which server to forward on... :(

    Read the article

  • Amazon EC2 firewall rules & VPN connections

    - by John
    I'm moving from Rackspace to Amazon EC2. One thing I like about our Rackspace setup is that it is extremely secure. The MySQL box can only be accessed via internal IPs, and we have a Cisco VPN firewall that allows us to dial in remotely and access port 3306 as though we were on the internal network. I'd like to figure out how to replicate this setup with EC2. How can I make the MySQL box so that port 3306 can only be accessed on the internal network? What about the VPN piece of things? I know Amazon has the VPC service, but it seems like that's for the purpose of connecting to an existing network. I don't have an existing network. I want to essentially create one inside Amazon and connect to that. What are my options? Any good tutorials on how to get started? Thanks in advance for your help

    Read the article

  • Setting up a linux switch

    - by Shahmir Javaid
    I have a C++ Program to sniff each and every packet that crosses my linux box. However i need to now get my linux box to listen to every traffic in my network. I could buy a managed switch and set up port spanning, but i aint paying 200+ £'s for a switch and plus gives me a chance to learn. My Network +---------Computer A | Internet-----Router------Switch-------------+---------Linux Box | +---------Computer B Proposed Network +---------Computer A | Internet-----Router------Linux Box--------Switch eth0^ ^eth1 | +---------Computer B How would i setup this in linux. Do i just configure both the ethernet on different IP Address on the same network. Or am i completelly on the wrong track My System Fedora 13. Thanks

    Read the article

  • Access port on machine by connecting to other machine via SSH?

    - by piquadrat
    I have to access my home router's web interface on port 80. Unfortunately, the only way into the network I have at the moment is SSH to another machine on the same network. me ---|---SSH Box----Home Router My Google foo seems to have abandoned me, I couldn't didn't find anything helpful. Any ideas? Thanks! To clarify: I'm not at home right now. I do however have access to one machine on the network (a QNAP NAS) over SSH. I need to access the home router web interface on port 80 from my notebook which is outside of the home network.

    Read the article

  • core.* files eating up server space (~50MB)

    - by skytreader
    I'm renting server space from someone and, upon logging in my control panel after quite sometime, noticed an abnormal spike (~50MB) in the disk usage. Upon investigating, I found a lot of core.* files scattered around my public_html directory. Each one is more than 5MB in size but no more than 6MB. The * part is all numbers (in programming regex, that should be core\.\d+). I downloaded one and checked the contents. There was a lot of balderdash characters (NUL mostly, but also a scattering of ETB, ETX, STX) but there's this block of readable text which says: This text is part of the internal format of your mail folder, and is not a real message. It is created automatically by the mail system software. If deleted, important folder data will be lost, and it will be re-created with the data reset to initial values. Pretty self-explanatory. A few blocks above the text are some more readable messages that look like logs but is sandwiched in between non printable characters. I've extracted some below. Scan not valid for mh mailboxes Bogus character 0x%x in news state Can't rewrite news state %.80s Error closing backup news state %.80s No state for newsgroup %.80s found Now, a few concerns: Am I under attack? The messages seem to be about my webmail but I don't use my personal webmail that much---only for a vanity email address and an inbox for an outdated comments system. However, lately, I seem to notice a spike in the spam for my vanity mail. (Note: the comments system is covered by a captcha but every now and then some get through. My vanity email has a spam filter but it isn't as good as I'd like). Next, if this is a feature, can I turn it off? Is it advisable to? I've only 150MB so you see why I'm fretting over a 50MB spike. Some final details: my only server-side scripts are in PHP. The directory which accumulated the most number of these core files is the one containing the Wordpress-managed subdomain of my site. I manage my server through CPanel. Lastly, I decided to delete this files and after some checking nothing seems amiss in my websites nor in my mail. They are indeed the ones responsible for the ~50MB spike as my disk space usage is back to expected.

    Read the article

  • Fix static ip address problems in Ubuntu 10.04

    - by jane
    I used Network Manager in Ubuntu 10.04 to set a static ip address and assigned one that was already in use. Now my computer will not boot (nfs crashes). I booted from a live cd to change the configuration on the file system in /etc/network/interfaces but the file looks to be the default. Where does the network manager (the gui from system- preferences) store it's configuration so I can overwrite it and enter the correct ip addresss and have a happy working computer again. thanks!!

    Read the article

  • Wordpress domain mapping error but only from my connection

    - by Michael Shimmins
    Recently when trying to access a Wordpress blog from a my network I get this error: Warning! Domain mapping upgrade for this domain not found. Please log in and go to the Domains Upgrades page of your blog to use this domain. If I request that URL from another connection (ie: remote desktop into another network and try from there), it works perfectly. Anyone got suggestions/ideas on why from my network the site errors, but from others it loads?

    Read the article

< Previous Page | 278 279 280 281 282 283 284 285 286 287 288 289  | Next Page >