Search Results

Search found 9305 results on 373 pages for 'loading animation'.

Page 289/373 | < Previous Page | 285 286 287 288 289 290 291 292 293 294 295 296  | Next Page >

  • Port forwarding on D-Link DIR-615 super-slow, useless

    - by Jaroslav Záruba
    Hello I have replaced my old router with DIR-615 from D-Link, and now the port forwarding is so slow it makes the router practically useless for requests coming from outside of my network. Accessing the router itself (admin UI) from outside is without any issues, no delay whatsoever. But when I try to access a service residing on any of the computers in my network from outside the requests take minutes and minutes. (E.g. I can see source of my GWT-app main page, but loading additional CSS and JS files takes years.) If anyone could recommend any further diagnostics I should do to figure out what is happening it would be great. Few notes: happens with more services (web-app on Tomcat, viewing directory index via Apache) it does not make a difference whether the service is hosted on wired or wireless PC accessing the service on a localhost works fine, as does any 'inner' communication turning off firewall on target PC does not make difference either (makes sense) when I replace this router with the old one (both 192.168.1.1) everything works fine I see nothing suspicious in the router's log I believe I have the latest firmware (4.11) DIR-615 sucks, it already died once completely Regards Jarda Z.

    Read the article

  • How to tell which process is hogging my CPU when they don't add up to 100%?

    - by endolith
    Ubuntu's System Monitor applet shows 100% CPU usage continuously. If I click it, the resources tab shows it at 100% continuously, too. If I go to processes, though, to find out which process is the culprit, there is nothing above 10%. If I run top there is nothing above 10%. The individual processes do not add up to 100%. I try killing lots of processes, but the overall usage continues to be 100%. How can I find out what's hogging the CPU? This is an unusual situation on a computer I use daily, which is never anywhere near 100% CPU unless I'm doing something that requires it (like loading 32 Firefox tabs), after which it goes back to a normal idle level. It's not a new install or anything. There is no reason the processor should be maxed out. I'm not sure when it started or if I changed something that caused it to happen. Normally I would use top or System Monitor and find the process that had gone out of control, but I can't find anything with those tools this time. It persists after reboots and everything. And the processor is obviously hot, so it's not an erroneous reading. Update: I tried killing every process, one at a time, until the problem went away, and killing vino-server finally fixed it, even though that process never went above 5%. I had enabled Remote Desktop a few days ago (and have obviously now disabled it). But the question remains: How did a single process manage to use 100% CPU while top only showed that process at 5%? How do I identify culprits like this in the future? Looks like I'm not the only one who's had this problem: Still a problem in both jaunty & karmic. Interestingly, both System Monitor & htop do not show the sum of individual processes being anywhere near 100% cpu.

    Read the article

  • Successful login with iscsiadm on target still doesn't create block device

    - by Halfgaar
    I've set up an experiment to test iscsitarget and initiator, which at some point worked. Later, I turned the setup back on and much to my dismay, the initiator machine stopped making block devices for its successful logins. As far as I know, I haven't changed anything on either machine. Some details: # iscsiadm -m node --login Logging in to [iface: default, target: iqn.2010-12.nl.ytec.arbiter:arbiter.lun1, portal: 10.0.0.1,3260] Logging in to [iface: default, target: iqn.2010-12.nl.ytec.arbiter:arbiter.lun2, portal: 10.0.0.1,3260] Login to [iface: default, target: iqn.2010-12.nl.ytec.arbiter:arbiter.lun1, portal: 10.0.0.1,3260]: successful Login to [iface: default, target: iqn.2010-12.nl.ytec.arbiter:arbiter.lun2, portal: 10.0.0.1,3260]: successful Sessions: # iscsiadm -m session tcp: [3] 10.0.0.1:3260,1 iqn.2010-12.nl.ytec.arbiter:arbiter.lun1 tcp: [4] 10.0.0.1:3260,1 iqn.2010-12.nl.ytec.arbiter:arbiter.lun2 Netstat: # netstat -n -p|grep 3260 tcp 0 0 10.0.0.2:48719 10.0.0.1:3260 ESTABLISHED 1078/iscsid tcp 0 0 10.0.0.2:48718 10.0.0.1:3260 ESTABLISHED 1078/iscsid /var/log/syslog doesn't give errors: Jan 27 11:41:49 vmnode001 kernel: [ 378.041749] scsi7 : iSCSI Initiator over TCP/IP Jan 27 11:41:49 vmnode001 kernel: [ 378.044180] scsi8 : iSCSI Initiator over TCP/IP lsscsi doesn't show my devices: [0:0:1:0] cd/dvd TSSTcorp DVD-ROM TS-L333A D100 /dev/sr0 [4:0:0:0] disk ATA Hitachi HUA72105 A74A - [4:0:1:0] disk ATA Hitachi HUA72105 A74A - [4:1:0:0] disk Dell VIRTUAL DISK 1028 /dev/sda And there are no block devices in /dev for it: # ls -1 /dev/sd* /dev/sda /dev/sda1 /dev/sda2 /dev/sda3 /dev/sda4 I tried loading all scsi kernel modules I could find, but that doesn't seem to be the problem. I reall don't get this; it used to work. I found people with similar problems (here and here) but no solution. Initiator is Debian Sqeeuze (testing), target is Debian Lenny (stable). iscsitarget is 0.4.16+svn162-3.1+lenny1, open-iscsi (initiator) is 2.0.871.3-2squeeze1. Target kernel: 2.6.26-2-amd64, initiator kernel: 2.6.32-5-amd64

    Read the article

  • Desktop virtualization

    - by gurpal2000
    Is there currently a proper Type 1 "desktop" hypervisor? Either free or not? This is just for tinkering around at home on some beefy Phenom machines. Basically i want to be able to run say 2 OSs on the same PC but without loading windows or a heavy flavour of linux and then use a hotkey to switch between them. I should get full performance out of them. So do i need something better than vmware workstation and/or virtualbox. I think these are "Type 2"? I already run VMWare w/s and VBox but is there a more performant solution? I saw a YouTube video from Citrix where a laptop was running XP and Vista. With the touch of a hot key they could switch between them. There was no visible underlying OS (there might be a hypervisor)? I have access to Citrix XenDesktop 3 enterprise edition evaluation. I realise this isn't for desktops but can i achieve my goal (geekiness) ? If i use the free XenServer 5.5.0 how do my client PCs access windows/linux/whatever from the xenserver? Is it via a thin client RDP type application? If so if there one for both windows and linux? Also if i do use XenServer can i use USB in either direction? What is Citrix receiver can i use that for (3) ? If so, is there some hotkey i can configure? whatever client is used to access the server software (whether it be on a different server or local) can i get full opengl/directx acceleration? what about Xen? i tried the Xen LiveCD but no clue as how to configure it. As you can see much confusion. Any help/pointers welcome. Cheers.

    Read the article

  • Make isolinux 4.0.3 chainload itself

    - by chainloader
    I have a bootable iso which boots into isolinux 4.0.3 and I want to make it chainload itself (my actual goal is to chainload isolinux.bin v4.0.1-debian, which should start up the Ubuntu10.10 Live CD, but for now I just want to make it chainload itself). I can't get isolinux to chainload any isolinux.bin, no matter what version. It either freezes or shows a "checksum error" message. I'm using VMWare to test the iso. Things I have tried: .com32 /boot/isolinux/chain.c32 /boot/isolinux/isolinux-debug.bin (chainload self) this shows Loading the boot file... Booting... ISOLINUX 4.03 2010-10-22 Copyright (C) 1994-2010 H. Peter Anvin et al isolinux: Starting up, DL = 9F isolinux: Loaded spec packet OK, drive = 9F isolinux: Main image LBA = 53F00100 ...and the machine freezes. Then I've tried this (chainload GRUB4DOS 0.4.5b) chainloader /boot/isolinux/isolinux-debug.bin Result: Error 13: Invalid or unsupported executable format Next try: (chainload GRUB4DOS 0.4.5b) chainloader --force /boot/isolinux/isolinux-debug.bin boot Result: ISOLINUX 4.03 2010-10-22 Copyright (C) 1994-2010 H. Peter Anvin et al isolinux: Starting up, DL = 9F isolinux: Loaded spec packet OK, drive = 9F isolinux: No boot info table, assuming single session disk... isolinux: Spec packet missing LBA information, trying to wing it... isolinux: Main image LBA = 00000686 isolinux: Image checksum error, sorry... Boot failed: press a key to retry... I have tried other things, but all of them failed miserably. Any suggestions?

    Read the article

  • No discs found when trying to install Windows 8 with UEFI

    - by Sahas Katta
    I have a Vizio Notebook (CN15-A5). It came pre-installed with Windows 8 x64 and is taking advantage of UEFI out of the box. The BIOS (APTOS AMI) is in Secure Boot mode with the OS selected as "Windows 8". I removed the stock HDD that came with the machine and put my own SSD into it. I created a Windows 8 Pro x64 installation disc on a 4GB USB flash drive formated as FAT32 since its apparently required for UEFI. When I boot from the USB Win8 installation disc, I get suck when I reach the "Custom: Install Windows only" section. Normally you would see a list of available discs and their partitions, however my entire list is blank. If I head back to the BIOS and disable Secure Boot and set the OS to "Other OS" and attempt again, I am able to see the list of available discs in the system and can install a copy of Windows 8. Unfortunately, doing it in this method results in an installation with a traditional 350 MB partition + OS partition instead of 4 partitions which is normal for a UEFI setup. Has anyone run into this problem? I've tried loading defaults in the BIOS and attempting to install via every combination with no luck. Any help would be appreciated.

    Read the article

  • CentOS 6.0 yum audacity dependency

    - by Kaemic
    I'm trying to install audacity on centos using yum and I cant force yum to resolve all dependencies, here's what i got, can someone help me with it (when I download the rpm file and click-installit i get the dependency problem too): # yum --disablerepo=c6-media install audacity-1.2.3-2.2.el4.rf.i386.rpm Loaded plugins: fastestmirror, refresh-packagekit Loading mirror speeds from cached hostfile * base: mirror.karneval.cz * centosplus: mirror.karneval.cz * extras: centos.vieth-server.de * rpmforge: fr2.rpmfind.net * updates: mirror.karneval.cz Setting up Install Process Examining audacity-1.2.3-2.2.el4.rf.i386.rpm: audacity-1.2.3-2.2.el4.rf.i386 Marking audacity-1.2.3-2.2.el4.rf.i386.rpm to be installed Resolving Dependencies --> Running transaction check ---> Package audacity.i386 0:1.2.3-2.2.el4.rf set to be updated --> Processing Dependency: wxGTK >= 2.4.0 for package: audacity-1.2.3-2.2.el4.rf.i386 --> Processing Dependency: libwx_gtk-2.4.so.0 for package: audacity-1.2.3-2.2.el4.rf.i386 --> Processing Dependency: libwx_gtk-2.4.so.0(WXGTK_2.4) for package: audacity-1.2.3-2.2.el4.rf.i386 --> Running transaction check ---> Package audacity.i386 0:1.2.3-2.2.el4.rf set to be updated --> Processing Dependency: libwx_gtk-2.4.so.0 for package: audacity-1.2.3-2.2.el4.rf.i386 --> Processing Dependency: libwx_gtk-2.4.so.0(WXGTK_2.4) for package: audacity-1.2.3-2.2.el4.rf.i386 ---> Package wxGTK.i686 0:2.8.12-1.el6.rf set to be updated --> Finished Dependency Resolution Error: Package: audacity-1.2.3-2.2.el4.rf.i386 (/audacity-1.2.3-2.2.el4.rf.i386) Requires: libwx_gtk-2.4.so.0 Error: Package: audacity-1.2.3-2.2.el4.rf.i386 (/audacity-1.2.3-2.2.el4.rf.i386) Requires: libwx_gtk-2.4.so.0(WXGTK_2.4) You could try using --skip-broken to work around the problem You could try running: rpm -Va --nofiles --nodigest

    Read the article

  • Disk Error on Boot (Possible boot sector issue)

    - by Choco
    I own a 4-5 year old Dell Dimension E510 with Windows XP: Media Center Edition. I have 2 drives installed: C Drive: Windows XP: Media Center Edition G Drive: 2 partitions: Windows 7 (beta) Windows XP (professional) That is also the order they are connected. The C Drive is my primary drive. When I attempt to boot the computer, the bios loading screen appears normally; the progress bar moves and it's fine. The very next page, however, supposed to be a boot choice. When I installed Windows 7 onto the G Drive in context of the C drive it added a boot selector to the C drive's boot sequence. It gives me the option of booting Windows 7 or Windows XP: Media Center Edition. However, my problem is now this: After the bios screen I previously mentioned, instead of a boot selector, I receive the following error: A disk read error occurred. Press CTRL+ALT+DEL to restart. The drive is spinning up normally. I hear no odd noises/clicks/scraping coming from it, even after disabling the other drive to listen to it carefully. According to me, it's a boot sector issue. I have never experienced this before, but maybe during a recent shutdown, Windows XP: MCE errored out and ruined the boot sector. Dilemma! I don't have the Windows XP: MCE disc, because it was installed by the factory. I have accessed the hidden partition on the drive before (you hit a key combination on the bios screen and it comes up with an interface to fix your drive). However, I don't want to reformat the drive (which is what the interface gives me the option to do). I want to possibly fix the boot sector. How can I achieve that?

    Read the article

  • How do I hook into Tar with BASH?

    - by orb
    Long Story Short I am working with Tar archives that contain PNG images in base64 encoding. I would like to use BASH (or whatever else works) to hook into the extraction function of Tar to decode PNG images from base64 encoding to standard PNG encoding after the files are unpacked. A simple cat $input-file | base64 -d >$output-file will successfully decode the images. Is there a way I can hook into tar -xf so that users do not have to do any (or minimal) extra work to decode the images? In the GNU Tar documentation (http://www.gnu.org/software/tar/manual/html_chapter/Backups.html#SEC97) I found that there are in fact variables reserved to hold the names of functions I desire to be hooked into various moments in Tar program execution. However, the documentation explains that these variables, along with other variables that can be set to configure Tar, are located in a file named backup-specs. Unfortunately, the path to this file is not given. Further, running sudo find / -name backup-specs tells me that this file is not present on my Ubuntu version 13.04 system. Background Information not included in the Long Story Short I have been working on a browser-based (WebGL) particle effect creation application (http://www.particleeffect.org), (https://github.com/cgrabowski/webgl-particle-effect-editor), (https://github.com/cgrabowski/webgl-particle-effect). I have began to write a client-side-only solution for saving and loading effect data as a tar archive. However, since client-side JavaScript has limited capability to process binary data, the images used as textures in the effect are saved with base64 encoding. I have been able to implement saving effect data as a Tar archive (haven't pushed that to Github yet). However, the images present in said Tar archive cannot be manipulated unless they are decoded from base64 encoding.

    Read the article

  • How to install Red Hat Enterprise Linux on Apple Macbook Pro MacBookPro4,1

    - by Todd V. Rovito
    I have a one year old Mac Book Pro that I am trying to get RHEL 5.4 installed on via bootcamp. No matter what I do I can't get the installer to boot. I have tried multiple DVD's and even verified the install works on a new Mac Book Pro. Most of the time the installer simply locks up. I usually use Linux text with all-generic-ide on the boot line. I removed the ide parameter and I just used linux text. The results I get are that a bunch of kernel messages appear then the background turns blue and a thin text box pops up saying its loading ata..... something it disappears too fast for me to read. Then the machine freezes. I pressed the alt function keys to see if I could look at the system log, here is what it says: Alt-f3 says "trying to mount CD device hda" Alt-f4 says status error: hda: lastFailedSense Hda: Failed opcode was: unknown Hda: Lost interrupt Hda: Drive not ready for command Ide-cd: command 0x3 timed out Above this junk it looks like it found the partition because it knew it was 20 GB and listed as /dev/sda3. I think it has something to do with the CD drive, is that possible? Thanks again for the support. PS I posted in the apple support forums ( Apple.com Support Discussions Boot Camp Installation and Storage) and didn't get an answer.

    Read the article

  • All websites migrated from server running IIS6 to IIS7

    - by Leah
    Hi, I hope someone will be able to help me with this. We have recently migrated all of our clients' sites to a new server running IIS7 - all the sites were originally running on a server running IIS6. Ever since the migration, lots of our clients are reporting error messages. There seems to be quite a number of issues related to sending emails and also, we have had the following error message reported by several different clients: Server Error in '/' Application. -------------------------------------------------------------------------------- Validation of viewstate MAC failed. If this application is hosted by a Web Farm or cluster, ensure that <machineKey> configuration specifies the same validationKey and validation algorithm. AutoGenerate cannot be used in a cluster. Description: An unhandled exception occurred during the execution of the current web request. Please review the stack trace for more information about the error and where it originated in the code. Exception Details: System.Web.HttpException: Validation of viewstate MAC failed. If this application is hosted by a Web Farm or cluster, ensure that <machineKey> configuration specifies the same validationKey and validation algorithm. AutoGenerate cannot be used in a cluster. I have read elsewhere that this error can appear if a button is clicked before the whole page has finished loading. But as this error has now appeared on multiple sites and only since the server migration, it seems to me that it must be something else. I was wondering if someone could tell me if there is something specific which needs to be changed for .NET sites when sites are moved from a server running IIS6 to a server running IIS7? I don't deal with the actual servers very much so I'm afraid this is very much a grey area for me. Any help would be very much appreciated.

    Read the article

  • Hardware doesn't work some times

    - by Ali
    I have an Asus n51vf laptop. I bought it not long time ago (less than a month) and installed Windows 7 on it. Since that it wasn't new when I bought it, I don't know, if the problem was occuring before re-installing Windows 7. There are two problems, that might (or might not) have something to do with each other: Problem The less annoying problem is that the screen flickers ONLY on YouTube when scrolling and/or pausing/playing the video or moving the curser over the video. The second more timeconsuming problem is that some of the hardware doesn't work when I turn up the computer. Then I have to reboot the computer and try again. Example: I turn on the computer, and the touchpad doesn't work - I then reboot and it works again. This has so far happened to the screen (leading to a black screen), the keyboard and the touchpad. More frequently the mouse. What have I tried to do so far? I tried reeinstalling the touchpad driver (Synaptic Touchpad driver from Asus Support Page) - didn't help at all. I even tried reinstalling the driver when the non-responding mouse on startup-problem occured (using the keyboard), but it asked me to reboot and didn't help at all. I also installed (and reinstalled) the graphics driver; it's a GeForce GT 130M. Now, the problem never occurs spontaneously - it only appears when booting my computer. I can even use the computer for heavy tasks (games, multiple programs running etc.) with no problem at all. I suspect, that the problem is in some booting mechanism that fails: Maybe the Windows driver loading? Motherboard problems?

    Read the article

  • Karmic iptables missing kernel moduyles on OpenVZ container

    - by luison
    After an unsuccessful p2v migration of my Ubuntu server to an OpenVZ container which I am stack with I thought I would give a try to a reinstall based on a clean OpenVZ template for Ubuntu 9.10 (from the OpenVZ wiki) When I try to load my iptables rules on the VM machine I've been getting errors which I believe are related to kernel modules not being loaded on the VM from the /vz/XXX.conf template model. I've been testing with a few post I've found but I was stack with the error: WARNING: Deprecated config file /etc/modprobe.conf, all config files belong into /etc/modprobe.d/. FATAL: Could not load /lib/modules/2.6.24-10-pve/modules.dep: No such file or directory iptables-restore v1.4.4: iptables-restore: unable to initialize table 'raw' Error occurred at line: 2 Try `iptables-restore -h' or 'iptables-restore --help' for more information. I read about the template not loading all iptables modules so I added modules to the XXX.conf of the VZ virtual machine like this: IPTABLES="ip_tables iptable_filter iptable_mangle ipt_limit ipt_multiport ipt_tos ipt_TOS ipt_REJECT ipt_TCPMSS ipt_tcpmss ipt_ttl ipt_LOG ipt_length ip_conntrack ip_conntrack_ftp ip_conntrack_irc ipt_conntrack ipt_state ipt_helper iptable_nat ip_nat_ftp ip_nat_irc" As the error remained I read that I should build dependencies again on the virtual machine: depmod -a but this returned an error: WARNING: Couldn't open directory /lib/modules/2.6.24-10-pve: No such file or directory FATAL: Could not open /lib/modules/2.6.24-10-pve/modules.dep.temp for writing: No such file or directory So I read again about creating the directory empty and redoing "depmod -a" it. I now don't get the dependancies error but get this and I don't have a clue how to proceed: WARNING: Deprecated config file /etc/modprobe.conf, all config files belong into /etc/modprobe.d/. FATAL: Module ip_tables not found. iptables-restore v1.4.4: iptables-restore: unable to initialize table 'raw' Error occurred at line: 2 Try `iptables-restore -h' or 'iptables-restore --help' for more information. I understand that iptables rules have to be different on the VM machine and perhaps some of the rules we are trying to apply (from our physical server) are not compatible but these are just source IP and destination port checks that I would like to be able to have available . I've heard that on the CentOS template there are no issues with this, so I understand is to do with VM config. Any help would be greatly appreciated.

    Read the article

  • How do I boot [embedded] linux from sd card?

    - by Brandon Yates
    I am hacking together a quick embedded linux system on a DM816x evm board. Previously I have been using TFTP and NFS to load my kernel and root filesystem to the board. I am now trying to switch over to loading everything from an SD card. I have my card partitioned such that uBoot and my kernel image are in one partition, and my rootFS in another partition. At power-on, Uboot starts correctly and successfully launches the kernel. However, the kernel is unable to mount the root file system. It appears that it doesn't recognize any SD (mmc) cards. It gives this error message. VFS: Cannot open root device "mmcblk0p2" or unknown-block(2,0) Please append a correct "root=" boot option; here are the available partitions: 1f00 256 mtdblock0 (driver?) 1f01 8 mtdblock1 (driver?) 1f02 2560 mtdblock2 (driver?) 1f03 1272 mtdblock3 (driver?) 1f04 2432 mtdblock4 (driver?) 1f05 128 mtdblock5 (driver?) 1f06 4352 mtdblock6 (driver?) 1f07 204928 mtdblock7 (driver?) 1f08 50304 mtdblock8 (driver?) Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(2,0) I feel like I'm missing something fundamental here. Why does it not recognize the root device I am trying to load from? Here is my uBoot boot script that is running: setenv bootargs console=ttyO2,115200n8 root=/dev/mmcblk0p2 rw mem=124M earlyprink vram=50M ti816xfb.vram=0:16M,1:16M,2:6M ip=off noinitrd;mmc init;fatload mmc 1 0x80009000 uImage;bootm 0x80009000

    Read the article

  • How to set only specific nginx server block into maintenance mode programmatically

    - by Ville Mattila
    I am looking for a solution to automate one of our application's deployment process. In the beginning of deployment, I would like to programmatically set the specified server into maintenance mode and finally after the deployment has been completed, remove the maintenance mode flag from the nginx server. By maintenance mode, I mean that nginx should response with HTTP Response Code 503 to all the requests (with possible custom page). I know how to set the server block to respond with 503 code (see http://www.cyberciti.biz/faq/custom-nginx-maintenance-page-with-http503/) but the question is about how to do this programmatically and most efficiently. Two options have came to my mind: Option 1: At the beginning of the deployment process, write a maintenance file into document root and conditionally check an existence of the maintenance file in nginx server config: server { if (-f $document_root/in_maintenance_mode) { return 503; } } This method contains certain overhead as the file existence is checked for each request. Is it possible to check the file existence only when loading the nginx config? Option 2: Deployment script replaces the whole nginx server configuration file with a maintenance version and swaps it back in the end of the deployment. If this method is used, I am concerned about possible other automation processes like puppet that may be override the maintenance configuration file.

    Read the article

  • Booting Debian5 (Lenny) on 2.6.16 Kernel

    - by bk
    Due to a proprietary kernel module that I don't have the source to and is very picky about what kernel versions it will load into (even with modprobe --f), I find myself in need of running a 2.6.16.XX kernel on my Debian5 machine. The machine boots fine with the 2.6.26-2 stock kernel, and I have successfully build and booted 2.6.26 and 2.6.31 based kernels by making a .deb and the ndoing dpkg -i. However, when I do the same approach for 2.6.16, the kernel hangs at boot. I'm testing this in a VMWare image, so I don't think its an issue of newer hardware not supported by the older kernel. For a working kernel, at boot I get: Uncompressing Linux.. OK booting the kernel Loading, please wait... mdadm: No devices listed in the conf file were found kinit name_to_dev_t /dev/hda5 (dev5,3) ... With 2.6.16.60, I never get the kinit message. It hangs after the mdadm line. There are no mdadm arrays on this machine, so I doubt its an issue inside the mdadm stuff, which is supposed to just error out as it does in the 2.6.26 case above, but for some reason I'm getting stuck getting into kinit. I've been banging my head against this wall so I'm very open to suggestions on how to go about troubleshooting this.

    Read the article

  • CentOS 5.6: How to resolve php53 RPM dependency conflict with php-mcrypt and php-common?

    - by Stefan Lasiewski
    We are running a CentOS 5.6 system, and want to install php53 with php-mcrypt. However, this introduces a dependency conflict between php-common & php53-common. Does anyone have a good workaround for this problem? host # yum install php-mcrypt Loaded plugins: fastestmirror Loading mirror speeds from cached hostfile * epel: linux.mirrors.es.net Setting up Install Process Resolving Dependencies --> Running transaction check ---> Package php-mcrypt.x86_64 0:5.1.6-15.el5.centos.1 set to be updated --> Processing Dependency: php-api = 20041225 for package: php-mcrypt --> Processing Dependency: php >= 5.1.6 for package: php-mcrypt --> Running transaction check ---> Package php.x86_64 0:5.1.6-27.el5_5.3 set to be updated --> Processing Dependency: php-cli = 5.1.6-27.el5_5.3 for package: php ---> Package php-common.x86_64 0:5.1.6-27.el5_5.3 set to be updated --> Running transaction check ---> Package php-cli.x86_64 0:5.1.6-27.el5_5.3 set to be updated --> Processing Conflict: php53-common conflicts php-common --> Finished Dependency Resolution php53-common-5.3.3-1.el5_6.1.x86_64 from installed has depsolving problems --> php53-common conflicts with php-common Error: php53-common conflicts with php-common You could try using --skip-broken to work around the problem You could try running: package-cleanup --problems package-cleanup --dupes rpm -Va --nofiles --nodigest This is apparently a known problem (See php-devel, Bug 700179 and Bug 695708) and this post at the CentOS forums, but there is no official fix yet.

    Read the article

  • How should I configure my Active Directory servers so that if one goes down, users are not kicked off SQL?

    - by Matty Brown
    Today, we shut down one of our Active Directory servers during office hours to check the loading on a UPS. Since all the server did was provide Active Directory in a separate building incase the main building caught fire, or whatever, we didn't think it would have any effect on our users. Seconds after the server was shut down, we had a dozen phone calls from users experiencing this issue:- [Microsoft SQL Server Login] SQLState: '28000' [Microsoft][ODBC SQL Server Driver][SQL Server]Login failed. The login is from an untrusted domain and cannot be used with authentication. Once we realized what had happened, we quickly rebooted the down Active Directory server. Problem solved. But why did this happen. And what if one day a server has a breakdown and is offline for hours, or days? Shouldn't the other Active Directory servers in the domain service authentication requests without disruption to users? We have 3 Windows Server 2003 Standard servers running Active Directory as Domain Controllers with Global Catalogs, all physically located on the same network at Gigabit speeds. I believe the domain was originally Windows Server 2000, or maybe even NT 4.0. Could the issue be to down to old Group Policies inherited from these old server OS's, or some default setting in Active Directory that needs changing?

    Read the article

  • CloudFlare dashboards empty, or performance issues

    - by Katafalkas
    I wanted to test CloudFlare performance so I set my image gallery domain on it and started testing. I have added PageRules for caching. And chose the Security: Essentially Off. I checked NS check tools and they say that my domain name is propagated with CloudFlare. For testing purpose I created a link that loads 200 images from that server, and was using loads.in website to determine how much it is faster. After trying few regions, I noticed that there were no improvement in loading speed. So I looked up the dashboards, and it was empty. I am not sure if I am doing something wrong, or made some error in my setup, or it takes few days to start caching or working properly, but at the moment - after a day of testing - dashboards are empty. Also the NS check tools sais that all name servers are propagated to CloudFlare and working fine. So I assume I got a bad performance because it is simply not working. I sent a letter to CloudFlare support team, but did not get any straight answer. So essentially my question is: Anyone has any experience with CloudFlare ? How long does it take for it to start caching static content to CDN ? Or there is simply something I am doing wrong ?

    Read the article

  • During Vista Repair - No operating system is listed.

    - by Jack Marchetti
    After a Windows update, my brother's Gateway computer loads to the "Step 3 of 3: 0%" and reboots. Safe Mode does not work. I placed a Vista DVD in the drive, and re-booted. (Note, this is my Vista DVD, not the Recovery/System disc that would come with a computer. Gateway does not give you CD's anymore. I believe they store recovery on a partition, but that partition has been wiped out). I chose "Repair Your Computer" I get a dialog box, but no operating system is listed. I'm then prompted to "Load Drivers". What drivers am I supposed to be loading here and where from? I placed a CD in the drive to "load drivers" but I don't see my DVD drive listed. All I saw where X:/Sources along with several Removable Media slots that were empty. On another screen I tried Startup Repair, which didn't do anything. I attempted to use System Restore - but it doesn't detect the hard drive. I'm guessing that I'm missing some sort of SATA driver and that is why the hard disk is not being found. Any ideas on this?

    Read the article

  • How can I debug solutions in Visual Studio 2010 from a network share?

    - by alastairs
    I've recently got a new Mac laptop and am running VS2010 in a Parallels virtual machine. It's mostly working out well for me, but I'm having some problems with debugging specific project types, related to the fact that the projects are being accessed via a network share. Test projects don't run because the test runner can't load the tests' DLL. Web projects fail to run in the Visual Studio mini web server, throwing the following exception: 'An error occurred loading a configuration file: Failed to start monitoring changes to path\to\web.config'. I've spent the evening trawling the web with little luck on this. After reading these two posts, I tried out the usual CasPol changes, but then found this post from one of the early VS2010 betas indicating that CasPol is no longer needed/supported in .NET 4.0 and VS2010. The network share is accessible via both a mapped drive and the UNC path. The virtual machine runs its applications under the administrator account, which appears to have all the necessary permissions on the network share to create, read, write and delete files and folders. I say "appears to have" as I can't view the Security Properties of the appropriate folder via Explorer: the Security tab just isn't present. Has anyone managed to successfully load and debug web and test projects from a network share in VS2010?

    Read the article

  • The MySQL service is in the status "starting" on windows

    - by andres descalzo
    I have several months working to "MySQL-5-1-47" on windows 2003. When I restarted, the service "MySQL" stay in this state "starting". The only way to raise the service was running the program directly: C:\Program Files\MySQL\MySQL Server 5.1\bin\mysqld This is the MySQL error log 100906 16:07:29 [Note] Event Scheduler: Purging the queue. 0 events 100906 16:07:32 InnoDB: Starting shutdown... 100906 16:07:37 [Note] Plugin 'FEDERATED' is disabled. 100906 16:07:38 InnoDB: Shutdown completed; log sequence number 0 44233 100906 16:07:38 [Note] mysqld: Shutdown complete 100906 16:07:39 InnoDB: Started; log sequence number 0 44233 100906 16:17:21 [Note] Plugin 'FEDERATED' is disabled. 100906 16:17:22 InnoDB: Started; log sequence number 0 44233 100906 16:22:01 [Note] Plugin 'FEDERATED' is disabled. 100906 16:22:02 InnoDB: Started; log sequence number 0 44233 100906 16:22:02 [Note] Event Scheduler: Loaded 0 events 100906 16:22:02 [Note] C:\Program Files\MySQL\MySQL Server 5.1\bin\mysqld.exe: ready for connections. Version: '5.1.47-community' socket: '' port: 3306 MySQL Community Server (GPL) The last lines are after loading the program from the shell Thank.

    Read the article

  • Can't access certain web sites - reset router, any ideas?

    - by IniTech
    EDIT: This problem was resolved by my ISP - had to do with damaged fiber in one of their locations. Thanks to everyone that helped. Not sure if this is the right site (I'm a StackOverflow user) so I thought I'd give it a shot. I'm having trouble connecting to certain sites on any of the 3 machines that are on my LAN. The following sites are returning "Problem Loading Page - The connection has timed out" Sourceforge.net CNet.com Microsoft.com OpenDNS.com even my company's webiste I was worried about possible malware/virus, but I don't think that is the case (given the inability to access my company's site and the fact that all 3 machines are having the same issues.) I've tried with IE8, FF, and Chrome I have reset my router (WRT54G) and my machine(s) multiple times. EDIT: It is also worth noting that this page spins constantly and no avatars show up (I'm assuming it is trying to access gravatar.com with no success.) EDIT: I have the same issues directly connected to the modem. So, any router config is probably not the issue I'm a programmer, not a network guy - any ideas?

    Read the article

  • How to set up GRUB2 chainloader to other Grub (Fedora, Debian) on GPT

    - by basic6
    I'm trying to set up a dedicated GRUB2 which (chain-)loads another GRUB on a disk with GPT partition table. Relevant partitions: /dev/sda1 BIOS_BOOT /dev/sda2 BOOT (ext2) /dev/sda3 FEDORA (ext4) /dev/sda6 DEBIAN (ext4) I installed Fedora first, using /dev/sda2 as boot partition. Then I installed Debian. The Debian installer recognized the Fedora installation and added it as boot entry, then installed its GRUB into the MBR. While this works for the moment, it's pretty messy, because every Debian update may change the boot config, removing the Fedora entry (tried it) and the other way around. That's why I want both systems to have their own boot loader and one main boot loader (that could reside on /dev/sda2), which loads one of them. This is what I've tried: Moved everything from /dev/sda2 to /dev/sda3/boot Removed /boot mount point in Fedora (so /dev/sda2 isn't used anymore) From a live Linux, installed GRUB2 to the MBR (grub-install --boot-directory=sda2 /dev/sda) Wrote a menu.lst: title Fedora root (hd0,2) chainloader +1 (Again, for Debian) Converted that to a grub.cfg script (grub-menu2cfg or something like that) When booting, actually got a GRUB2 menu with "Fedora" (and "Debian") When selecting any one of those: error: invalid signature Issued "grub-install /dev/sda6" (and ...sda3) from all kinds of live Linux systems, all of which failed with another error message (in the case of the Debian installer, without explanation at all) Added --force to the chainloader line, now it says "loading", then reboots Found douzens of howtos, none of which seem to work for me Since I get the self-made GRUB2 menu on bootup, I've at least successfully installed the first stage of GRUB, right? When trying to chainload, some signature is checked and seems to be wrong - how do I fix it? The boot menus (Fedora with its different Kernel versions and Debian with Debian and Fedora as well) are now on the system partitions (/dev/sda3, /dev/sda6), is there anything else to do on these partitions, so they can be chainloaded? Any help is greatly appreciated.

    Read the article

  • Server nearly unusable when doing disk writes

    - by Wikser
    My question closely relates to my last question here on serverfault. I was copying about 5GB from a 10 year old desktop computer to the server. The copy was done in Windows Explorer. In this situation I would assume the server to be bored by the dataflow. But as usual with this server, it really slowed down. At least I could work with the remote session, even there was some serious latency. The copy took its time (20min?). In this time I went to a colleague and he tried to log in in the same server via remote desktop (for some other reason). It took about a minute to get to the login screen, a minute to open the control panel, a minute to open the performance monitor, ... Icons were loading maybe one per second. We saw the following (from memory): CPU: 2% Avg. Queue Length: 50 Pages/sec: 115 (?) There was no other considerable activity on the server. The server seldom serves some ASP.NET pages, which became also very slow in this time. The relevant configuration is as follows: Windows 2003 SEAGATE ST3500631NS (7200 rpm, 500 GB) LSI MegaRAID based RAID 5 4 disks, 1 hot spare Write Through No read-ahead Direct Cache Mode Harddisk-Cache-Mode: off Is this normal behaviour for such a configuration? What measurements could give further clues? Is it reasonable to reduce the priority of such copy I/O and favour other processes like the remote desktop? How would you do that? Many thanks!

    Read the article

< Previous Page | 285 286 287 288 289 290 291 292 293 294 295 296  | Next Page >