Search Results

Search found 29093 results on 1164 pages for 'network interface'.

Page 296/1164 | < Previous Page | 292 293 294 295 296 297 298 299 300 301 302 303  | Next Page >

  • Cisco ASA Hairpinning with Dynamic IP

    - by Joseph Sturtevant
    I currently have my Cisco ASA 5505 firewall configured to forward port 80 from the outside interface to a host on my dmz interface. I also need to allow clients on my inside interface to access the host in the dmz by entering the public ip / dns record in their browsers. I was able to do that by following the instructions here, resulting in the following configuration: static (dmz,outside) tcp interface www 192.168.1.5 www netmask 255.255.255.255 static (dmz,inside) tcp 74.125.45.100 www 192.168.1.5 www netmask 255.255.255.255 (Where 74.125.45.100 is my public IP and 192.168.1.5 is the IP of the dmz host) This works great except for the fact that my network has a dynamic public IP and this configuration will therefore break as soon as my public IP changes. Is there a way to do what I want with a dynamic ip? Note: Adding an internal DNS record won't solve my problem since I have multiple dmz hosts mapped to different ports on the public IP.

    Read the article

  • When I restart my virtual enviorment it does not re-bind to the IP address

    - by RoboTamer
    The IP does no longer respond to a remote ping With restart I mean: lxc-stop -n vm3 lxc-start -n vm3 -f /etc/lxc/vm3.conf -d -- /etc/network/interfaces auto lo iface lo inet loopback up route add -net 127.0.0.0 netmask 255.0.0.0 dev lo down route add -net 127.0.0.0 netmask 255.0.0.0 dev lo # device: eth0 auto eth0 iface eth0 inet manual auto br0 iface br0 inet static address 192.22.189.58 netmask 255.255.255.248 gateway 192.22.189.57 broadcast 192.22.189.63 bridge_ports eth0 bridge_fd 0 bridge_hello 2 bridge_maxage 12 bridge_stp off post-up ip route add 192.22.189.59 dev br0 post-up ip route add 192.22.189.60 dev br0 post-up ip route add 192.22.189.61 dev br0 post-up ip route add 192.22.189.62 dev br0 -- /etc/lxc/vm3.conf lxc.utsname = vm3 lxc.rootfs = /var/lib/lxc/vm3/rootfs lxc.tty = 4 #lxc.pts = 1024 # pseudo tty instance for strict isolation lxc.network.type = veth lxc.network.flags = up lxc.network.link = br0 lxc.network.name = eth0 lxc.network.mtu = 1500 #lxc.cgroup.cpuset.cpus = 0 # security parameter lxc.cgroup.devices.deny = a # Deny all access to devices lxc.cgroup.devices.allow = c 1:3 rwm # dev/null lxc.cgroup.devices.allow = c 1:5 rwm # dev/zero lxc.cgroup.devices.allow = c 5:1 rwm # dev/console lxc.cgroup.devices.allow = c 5:0 rwm # dev/tty lxc.cgroup.devices.allow = c 4:0 rwm # dev/tty0 lxc.cgroup.devices.allow = c 4:1 rwm # dev/tty1 lxc.cgroup.devices.allow = c 4:2 rwm # dev/tty2 lxc.cgroup.devices.allow = c 1:9 rwm # dev/urandon lxc.cgroup.devices.allow = c 1:8 rwm # dev/random lxc.cgroup.devices.allow = c 136:* rwm # dev/pts/* lxc.cgroup.devices.allow = c 5:2 rwm # dev/pts/ptmx lxc.cgroup.devices.allow = c 254:0 rwm # rtc # mounts point lxc.mount.entry=proc /var/lib/lxc/vm3/rootfs/proc proc nodev,noexec,nosuid 0 0 lxc.mount.entry=devpts /var/lib/lxc/vm3/rootfs/dev/pts devpts defaults 0 0 lxc.mount.entry=sysfs /var/lib/lxc/vm3/rootfs/sys sysfs defaults 0 0

    Read the article

  • Is bonding mode=5 a solution against MAC flapping?

    - by Yuri
    There is two are interconnected Cisco WS-2950T. By the one GBIC port on first switch connected a first NIC of bonding interface, and by the one GBIC port on second switch connected a second NIC of bonding interface. Of course the both switches sees the bonding MAC-address only on one interface (eg it is GBIC on first switch) and all incoming traffic for bonding interface passes through this GBIC. But in "mode=5" all outgoing traffic are distributed between the all interfaces that make bond. In this case, the packets will be dropped from the second switch and anyway will going through the first switch? Or the division will be working?

    Read the article

  • Fortigate - Accessing a Virtual Server address from several interfaces

    - by Jeremy G
    I am setting up a new application in its own DMZ on our Fortigate 300C firewalls. I have defined a load-balancing configuration for part of the application, and this works fine for traffic coming in from our internal network. However, I would also like this application to be reachable from other DMZs, for inter-application traffic, and from the SSL VPN interface. I can't seem to define the required policy, and it seems this is due to Virtual Servers being bound to the client interface on the Fortigate rather than the server interface (and so my virtual IP is not accessible from any of these other interfaces) Does anyone have an idea how I might go about this ? I guess I could create other virtual IPs for each interface, but this gets complicated to handle as clients need to change the address they use depending on how they are connecting. Thanks, Jeremy G

    Read the article

  • How to restrict file system when logged into terminal services

    - by pghcpa
    What I need to accomplish: With one login, when user is physically in the building I need them to see everything. When they are using terminal services with same login they should not be able to see the file system on the network. I can lock down the PC running terminal services as that is its only use. Details: Windows/2003 Server with terminal services. One login for a user (e.g., johndoe). When johndoe logs into the network at his desk in the office, he can see the network files according to group policy. When johndoe logs into terminal services from outside the building, we do not want to allow him see the network. Using 2x to do a published app, but that app has a "feature" that allows user to see network. Published application on termina services (only) is a document management system that is tied to windows login, so I can't give them two logins. With one login, when they are in the building I need them to see everything. When they are using terminal services they should not be able to see the network. I can lock down the PC running terminal services as that is its only use.

    Read the article

  • Unable to connect to EC2 instance after "reboot"

    - by KPL
    I am not able to connect to my m1.small instance after rebooting it. I have already associated the public IP with this instance. Upon checking the system log, this seems to be the issue: cloud-init-nonethttp://11.84: waiting 10 seconds for network device cloud-init-nonethttp://21.85: waiting 120 seconds for network device cloud-init-nonethttp://141.85: gave up waiting for a network device. Cloud-init v. 0.7.3 running 'init' at Sun, 18 May 2014 07:02:55 +0000. Up 142.54 seconds. ci-info: +++++++++++++++++++++++Net device info++++++++++++++++++++++++ ci-info: +--------+-------+-----------+-----------+-------------------+ ci-info: | Device | Up | Address | Mask | Hw-Address | ci-info: +--------+-------+-----------+-----------+-------------------+ ci-info: | lo | True | 127.0.0.1 | 255.0.0.0 | . | ci-info: | eth0 | False | . | . | 02:43:xx:xx:xx:xx | ci-info: +--------+-------+-----------+-----------+-------------------+ ci-info: !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!Route info failed!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! A bunch of these follow the above message: 2014-05-18 07:02:56,178 - url_helper.pyWARNING: Calling http://169.254.169.254/2009-04-04/meta-data/instance-id failed 0/120s: request error [HTTPConnectionPool(host='169.254.169.254', port=80): Max retries exceeded with url: /2009-04-04/meta-data/instance-id (Caused by : Errno 101] Network is unreachable) This is obviously related to the network interface not being working correctly. I have tried this so far: Relaunch a new instance from the custom AMI (created from EBS) of the failing instance. The same error shows up in the logs. Attach a new network interface to the EC2 instance. The error still persists. eth1 shows up in the list but the "up" column is False.

    Read the article

  • VRF Internet Gateway Multiple External IP's 1 Internal IP to AWS

    - by user223903
    Trying to setup VRF for the first time and its not working for me even though I keep reading everything online. IP's are different to real life. I have an Internet connection which I can ping to my router in the current setup below 195.45.73.22 I have a block of ip addresses 195.45.121.0/27 I want to setup multiple VPN's to AWS so need to have multiple external ip's thus the block of IP addresses. I have setup the 2nd and 3rd IP address but can not ping them from external. Any help would be grateful. Bryan ip source-route ! ip vrf Internet rd 1:1 route-target export 1:1 route-target import 1:1 ip vrf AWSSydney1 rd 2:2 route-target export 2:2 route-target import 2:2 route-target import 1:1 ip vrf AWSSydney2 rd 3:3 route-target export 3:3 route-target import 3:3 route-target import 1:1 ip cef no ip domain lookup no ipv6 cef multilink bundle-name authenticated interface FastEthernet0/0 description Vocus Internet no ip address speed 100 full-duplex interface FastEthernet0/0.1 encapsulation dot1Q 1 native ip address 195.45.73.22 255.255.255.252 interface FastEthernet0/0.2 encapsulation dot1Q 2 ip vrf forwarding AWSSydney1 ip address 195.45.121.1 255.255.255.224 interface FastEthernet0/0.3 encapsulation dot1Q 3 ip vrf forwarding AWSSydney2 ip address 195.45.121.2 255.255.255.224 interface FastEthernet0/1 description LAN_SIDE ip address 10.0.0.5 255.255.255.0 speed 100 full-duplex no mop enabled ip forward-protocol nd ip route 0.0.0.0 0.0.0.0 195.45.73.21 ip route vrf Internet 0.0.0.0 0.0.0.0 195.45.73.21

    Read the article

  • Windows Server (SBS) 2008 - Telephony service won't start (missing permissions)

    - by Uri
    I am running a SBS 2008 server. It's setup as the domain controller for the network. After a reboot, the Telephony service (and all services that depend on it) refuses to start under the Network Service account. The error given is: Error 1297: A privilege that the service requires to function properly does not exist in the service account configuration. You may use the Services Microsoft Management Console (MMC) snap-in (services.msc) and the Local Security Settings MMC snap-in (secpol.msc) to view the service configuration and the account configuration. This has caused all the network services not to be accessible e.g. terminal services, VPN (RRAS), SQL Server instances. The SSH daemon I have running on the box will accept connections only from localhost, but won't respond on the network. After searching around, the only advice I could find was to grant the Network Service account these permissions: Adjust memory quotas for a process Replace a process level token I set those permissions on both the Default Domain Policy and the Default Domain Controller Policy, but it seemingly had no effect. Most of the services will start if I change them to run under the Local System account, but that didn't make them accessible on the network. I even tried removing the Routing and Remote Access Services feature, rebooting and reinstalling it, but the issue remains. Any ideas?

    Read the article

  • Persistent static route stops working after VPN drops and reconnects

    - by user76157
    I've got a VPN between two networks, one home and one office (A and B). Their subnets are: (A) 192.168.1.0 and (B) 192.168.0.0 The two networks have identical ADSL routers. Unfortunately these can only do dial-out VPN. So I've got a Windows 2008 server on Network B acting as a VPN server (ServerB). Network A's router (RouterA) passes through Network B's router and connects via PPTP to ServerB. RouterA is assigned the static IP 192.168.0.40 on Network B. There's a persistent static route on ServerB telling it to use 0.40 for all requests to Network A's subnet, 192.168.1.0. (route -p add 192.168.1.0 mask 255.255.255.0 192.168.0.40). This enables ServerB to ping all machines on A (and those machines to ping ServerB). The VPN connection occasionally drops (I'm not sure why - it's set to remain always on and seems to drop randomly). This wouldn't be too much of a problem, as it reconnects automatically and quickly, except that when it does reconnect, the static route on ServerB no longer works. Route print (on ServerB) shows that the persistent static route still exists. However a tracert to a machine on Network A doesn't use the static route; it tries instead to use ServerB's default gateway (which is RouterB), and fails to find the machine. Deleting and re-adding the static route fixes the problem - a tracert uses the static route. At the moment, a batch file to delete and re-add the static route is scheduled to run every day. But this is clearly far from an ideal solution! I hope that's not too confusing. Any help would be very much appreciated.

    Read the article

  • Bash Script - Traffic Shaping

    - by Craig-Aaron
    hey all, I was wondering if you could have a look at my script and help me add a few things to it, How do I get it to find how many active ethernet ports I have? and how do I filter more than 1 ethernet port How I get this to do a range of IP address? Once I have a few ethenet ports I need to add traffic control to each one #!/bin/bash # Name of the traffic control command. TC=/sbin/tc # The network interface we're planning on limiting bandwidth. IF=eth0 # Network card interface # Download limit (in mega bits) DNLD=10mbit # DOWNLOAD Limit # Upload limit (in mega bits) UPLD=1mbit # UPLOAD Limit # IP address range of the machine we are controlling IP=192.168.0.1 # Host IP # Filter options for limiting the intended interface. U32="$TC filter add dev $IF protocol ip parent 1:0 prio 1 u32" start() { # Hierarchical Token Bucket (HTB) to shape bandwidth $TC qdisc add dev $IF root handle 1: htb default 30 #Creates the root schedlar $TC class add dev $IF parent 1: classid 1:1 htb rate $DNLD #Creates a child schedlar to shape download $TC class add dev $IF parent 1: classid 1:2 htb rate $UPLD #Creates a child schedlar to shape upload $U32 match ip dst $IP/24 flowid 1:1 #Filter to match the interface, limit download speed $U32 match ip src $IP/24 flowid 1:2 #Filter to match the interface, limit upload speed } stop() { # Stop the bandwidth shaping. $TC qdisc del dev $IF root } restart() { # Self-explanatory. stop sleep 1 start } show() { # Display status of traffic control status. $TC -s qdisc ls dev $IF } case "$1" in start) echo -n "Starting bandwidth shaping: " start echo "done" ;; stop) echo -n "Stopping bandwidth shaping: " stop echo "done" ;; restart) echo -n "Restarting bandwidth shaping: " restart echo "done" ;; show) echo "Bandwidth shaping status for $IF:" show echo "" ;; *) pwd=$(pwd) echo "Usage: tc.bash {start|stop|restart|show}" ;; esac exit 0 thanks

    Read the article

  • Browsing Playstation 3 from Ubuntu Box

    - by zfranciscus
    Hi, My Goal here is to be able to transfer files from my Ubuntu 10.04 box to my PS3 over a wireless network. My PS3 and my Ubuntu Box is on the same home network. These are some stuff that I tried: I can't see my PS 3 from 'Places ? Network' nor other computer that is running on windows. I am still puzzled by this fact. I have not tried ping-ing my PS3. I'll try that later today and post the result in the forum I install PS3MediaServer (http://code.google.com/p/ps3mediaserver/). Someone in the PS3 chat forum (http://www.ps3chat.com/playstation-3...lp-please.html) claims that it will enable your ubuntu box to browse PS3. So I downloaded PS3MediaServer, and ran the software. The status tab keep showing "Waiting ...". It seems that PS3MediaServer can't find my PS3. Some how I feel that 1 and 2 are related somehow.Perhaps that there is something wrong with my Ubuntu network settings that is preventing my ubuntu box from looking up other device on the network. I can go to the Internet fine, but I can't see other device on my network. Does anyone have any experience in this area. I would like to hear your experience and perhaps some solution. Any kind of hints or help will be greatly appreciated. Cheers

    Read the article

  • How to force certain traffic through GRE tunnel?

    - by wew
    Here's what I do. Server (public internet is 222.x.x.x): echo 'net.ipv4.ip_forward=1' >> /etc/sysctl.conf sysctl -p iptunnel add gre1 mode gre local 222.x.x.x remote 115.x.x.x ttl 255 ip add add 192.168.168.1/30 dev gre1 ip link set gre1 up iptables -t nat -A POSTROUTING -s 192.168.168.0/30 -j SNAT --to-source 222.x.x.x iptables -t nat -A PREROUTING -d 222.x.x.x -j DNAT --to-destination 192.168.168.2 Client (public internet is 115.x.x.x): iptunnel add gre1 mode gre local 115.x.x.x remote 222.x.x.x ttl 255 ip add add 192.168.168.2/30 dev gre1 ip link set gre1 up echo '100 tunnel' >> /etc/iproute2/rt_tables ip rule add from 192.168.168.0/30 table tunnel ip route add default via 192.168.168.1 table tunnel Until here, all seems going right. But then 1st question, how to use GRE tunnel as a default route? Client computer is still using 115.x.x.x interface as default. 2nd question, how to force only ICMP traffic to go through tunnel, and everything else go default interface? I try doing this in client computer: ip rule add fwmark 200 table tunnel iptables -t mangle -A OUTPUT -p udp -j MARK --set-mark 200 But after doing this, my ping program will timeout (if I not doing 2 command above, and using ping -I gre1 ip instead, it will works). Later I want to do something else also, like only UDP port 53 through tunnel, etc. 3rd question, in client computer, I force one mysql program to listen on gre1 interface 192.168.168.2. In client computer, there's also one more public interface (IP 114.x.x.x)... How to forward traffic properly using iptables and route so mysql also respond a request coming from this 114.x.x.x public interface?

    Read the article

  • 1000Base-X layer 2/MAC address details

    - by user69971
    A layer 2 Ethernet frame is sent with a source and destination MAC address. Given a 100Base-TX (copper) trunk between two Cisco switches, I can do a "show interface fa 0/0" on S1 to see the MAC address assigned to the trunking interface, then go to Switch2 and do a "show mac address-table" and find the MAC address of the S1 fa 0/0 interface as a dynamically learned MAC in the table. Given a similar setup with a 1000Base-X (fiber GBIC) trunk, the MAC address shown in "show interface gi 0/0" on S1 does not show up in the MAC address-table of S2. Everything I can find online indicates that 1000Base-X uses largely the same layer 2 format as copper connections. There's some slight alterations - minimum frame size is slightly larger - but the fundamentals of the frame structure appear to be the same, including transmission with a source and destination L2 address. Why doesn't the address of gi 0/0 show up in the MAC address table of the connection switch? The only thing which seems to make sense would be that the GBIC has its own MAC address, almost as if its acting as a mini 2-port switch or hub, with the switch-assigned MAC address showing up on the interface connection and a different MAC address assigned to the fiber side. If this is the case, is there any way to see the GBIC MAC address on the switch? (I've tried to look up the details in IEEE 802.3z but it doesn't seem to be available without an IEEE membership or purchasing the standard. I find the base 802.3 PDFs for download, but not 802.3z.)

    Read the article

  • Group Policy GPO not 'seen' at client

    - by fukawi2
    I have a new OU (natorg.local\NATO\Users) that I am trying to apply GP to. I have created a new user in this OU, and linked the 3 GPO's to this OU: DESKTOP - Folder Redirection (AppData) DESKTOP - Folder Redirection (Desktop) DESKTOP - Folder Redirection (Documents) Hopefully the names are sufficient to suggest what they do exactly. The settings are under User Settings so there is no Loopback processing required (if my understanding is correct). GP Modelling for the user and specific computer says that the GPOs will/should be applied, however on the client, gpresult doesn't even appear to see the GPOs under either "Applied" or "Not Applied": USER SETTINGS -------------- CN=Amir,OU=Users,OU=NATO,DC=natorg,DC=local Last time Group Policy was applied: 25/06/2012 at 11:07:13 AM Group Policy was applied from: svr-addc-01.natorg.local Group Policy slow link threshold: 500 kbps Applied Group Policy Objects ----------------------------- LAPTOPS - Power Settings WSUS - Set Server Address OUTLOOK - Auto Archive SECURITY - Lock Screen After Idle Default Domain Policy DESKTOP - Regional Settings NETWORK - Proxy Configuration NETWORK - IE General Config OFFICE - Trusted Locations OFFICE - Increase Privacy OUTLOOK - Disable Junk Filter DESKTOP - Disable Windows Error Reporting DESKTOP - Hide Language Bar NETWORK - Disable Skype DESKTOP - Disable Thumbs.db Creation WSUS - Set Server Address The following GPOs were not applied because they were filtered out ------------------------------------------------------------------- Local Group Policy Filtering: Not Applied (Empty) NETWORK - Google Chrome Configuration Filtering: Not Applied (Empty) SYSTEM - Event Log Configuration Filtering: Not Applied (Empty) SECURITY - Local Administrator Password Filtering: Not Applied (Empty) NETWORK - Disable Windows Messenger Filtering: Not Applied (Empty) SECURITY - Audit Policy Filtering: Not Applied (Empty) WSUS - Automatic Install Filtering: Not Applied (Empty) NETWORK - Firewall Configuration Filtering: Not Applied (Empty) DESKTOP - Enable Offline Files Filtering: Not Applied (Empty) I haven't altered permissions on the GPO's at all, no WMI filtering... As I said, GP Modelling says that they should be applied. GPResult on the client correctly identifies itself as being the correct OU (CN=Amir,OU=Users,OU=NATO,DC=natorg,DC=local) There are 2 x 2008R2 and a 2003 DC, domain is 2003 level, client is Windows XP SP3. Can anyone suggest why these GP Objects would be "invisible" to the client?

    Read the article

  • DHCP forwarding behind access list on a Cisco Catalyst

    - by Ásgeir Bjarnason
    I'm having some trouble with forwarding DHCP from a subnet behind an access list on a Cisco Catalyst 4500 switch. I'm hoping somebody can see the mistake I'm making. The subnet is defined like this: (first three octets of IP addresses and vrf name anonymized) interface Vlan40 ip vrf forwarding vrf_name ip address 10.10.10.126 255.255.255.0 secondary ip address 10.10.10.254 255.255.255.0 ip access-group 100 out ip helper-address 10.10.20.36 no ip redirects I tried turning on a VMWare machine on this subnet that was configured to use DHCP, but I never got a DHCP response and the DHCP server didn't receive a request. I tried putting the following in the access-list: access-list 100 permit udp host 10.10.10.254 host 10.10.20.36 eq bootps access-list 100 permit udp host 10.10.10.254 host 10.10.20.36 eq bootpc access-list 100 permit udp host 10.10.20.36 host 10.10.10.254 eq bootps access-list 100 permit udp host 10.10.20.36 host 10.10.10.254 eq bootpc That didn't help. Can anybody see what the problem is? I know that the DHCP server works; our whole network is running off of this DHCP server I also know that the subnet works because we have active servers running on the network The DHCP scope is already defined on the DHCP server The subnet is correctly defined on the VMWare server (already servers running on the subnet on VMWare) Edit 2012-10-19: This is solved! The subnet had formerly been defined as a /25 network, but was then expanded into a /24 network. When the DHCP scope was altered after this change it was done incorrectly; the gateway was moved to .254, the leasable IP range was in the lower half of the /24 subnet but we forgot to change the CIDR prefix from /25 into /24. This happened some 2 years ago, and we didn't need to use DHCP on this server network again until this week. Thank you MDMarra and Jason Seemann for looking at the question and trying to troubleshoot. Now I'm wondering if I should mark Jason's answer as the accepted answer (I am new to the Stack Exchange network, so I don't know the etiquette of what to do if I misstated the question like in this case).

    Read the article

  • How do I make Linux recognize a new SATA /dev/sda drive I hot swapped in without rebooting?

    - by Philip Durbin
    Hot swapping out a failed SATA /dev/sda drive worked fine, but when I went to swap in a new drive, it wasn't recognized: [root@fs-2 ~]# tail -18 /var/log/messages May 5 16:54:35 fs-2 kernel: ata1: exception Emask 0x10 SAct 0x0 SErr 0x50000 action 0xe frozen May 5 16:54:35 fs-2 kernel: ata1: SError: { PHYRdyChg CommWake } May 5 16:54:40 fs-2 kernel: ata1: link is slow to respond, please be patient (ready=0) May 5 16:54:45 fs-2 kernel: ata1: device not ready (errno=-16), forcing hardreset May 5 16:54:45 fs-2 kernel: ata1: soft resetting link May 5 16:54:50 fs-2 kernel: ata1: link is slow to respond, please be patient (ready=0) May 5 16:54:55 fs-2 kernel: ata1: SRST failed (errno=-16) May 5 16:54:55 fs-2 kernel: ata1: soft resetting link May 5 16:55:00 fs-2 kernel: ata1: link is slow to respond, please be patient (ready=0) May 5 16:55:05 fs-2 kernel: ata1: SRST failed (errno=-16) May 5 16:55:05 fs-2 kernel: ata1: soft resetting link May 5 16:55:10 fs-2 kernel: ata1: link is slow to respond, please be patient (ready=0) May 5 16:55:40 fs-2 kernel: ata1: SRST failed (errno=-16) May 5 16:55:40 fs-2 kernel: ata1: limiting SATA link speed to 1.5 Gbps May 5 16:55:40 fs-2 kernel: ata1: soft resetting link May 5 16:55:45 fs-2 kernel: ata1: SRST failed (errno=-16) May 5 16:55:45 fs-2 kernel: ata1: reset failed, giving up May 5 16:55:45 fs-2 kernel: ata1: EH complete I tried a couple things to make the server find the new /dev/sda, such as rescan-scsi-bus.sh but they didn't work: [root@fs-2 ~]# echo "---" > /sys/class/scsi_host/host0/scan -bash: echo: write error: Invalid argument [root@fs-2 ~]# [root@fs-2 ~]# /root/rescan-scsi-bus.sh -l [snip] 0 new device(s) found. 0 device(s) removed. [root@fs-2 ~]# [root@fs-2 ~]# ls /dev/sda ls: /dev/sda: No such file or directory I ended up rebooting the server. /dev/sda was recognized, I fixed the software RAID, and everything is fine now. But for next time, how can I make Linux recognize a new SATA drive I have hot swapped in without rebooting? The operating system in question is RHEL5.3: [root@fs-2 ~]# cat /etc/redhat-release Red Hat Enterprise Linux Server release 5.3 (Tikanga) The hard drive is a Seagate Barracuda ES.2 SATA 3.0-Gb/s 500-GB, model ST3500320NS. Here is the lscpi output: [root@fs-2 ~]# lspci 00:00.0 RAM memory: nVidia Corporation MCP55 Memory Controller (rev a2) 00:01.0 ISA bridge: nVidia Corporation MCP55 LPC Bridge (rev a3) 00:01.1 SMBus: nVidia Corporation MCP55 SMBus (rev a3) 00:02.0 USB Controller: nVidia Corporation MCP55 USB Controller (rev a1) 00:02.1 USB Controller: nVidia Corporation MCP55 USB Controller (rev a2) 00:04.0 IDE interface: nVidia Corporation MCP55 IDE (rev a1) 00:05.0 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:05.1 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:05.2 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:06.0 PCI bridge: nVidia Corporation MCP55 PCI bridge (rev a2) 00:08.0 Bridge: nVidia Corporation MCP55 Ethernet (rev a3) 00:09.0 Bridge: nVidia Corporation MCP55 Ethernet (rev a3) 00:0a.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0b.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0c.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0d.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0e.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0f.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 00:19.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:19.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:19.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:19.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 03:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA G200e [Pilot] ServerEngines (SEP1) (rev 02) 04:00.0 PCI bridge: NEC Corporation uPD720400 PCI Express - PCI/PCI-X Bridge (rev 06) 04:00.1 PCI bridge: NEC Corporation uPD720400 PCI Express - PCI/PCI-X Bridge (rev 06) Update: In perhaps a dozen cases, we've been forced to reboot servers because hot swap hasn't "just worked." Thanks for the answers to look more into the SATA controller. I've included the lspci output for the problematic system above (hostname: fs-2). I could still use some help understanding what exactly isn't supported hardware-wise in terms of hot swap for that system. Please let me know what other output besides lspci might be useful. The good news is that hot swap "just worked" today on one of our servers (hostname: www-1), which is very rare for us. Here is the lspci output: [root@www-1 ~]# lspci 00:00.0 RAM memory: nVidia Corporation MCP55 Memory Controller (rev a2) 00:01.0 ISA bridge: nVidia Corporation MCP55 LPC Bridge (rev a3) 00:01.1 SMBus: nVidia Corporation MCP55 SMBus (rev a3) 00:02.0 USB Controller: nVidia Corporation MCP55 USB Controller (rev a1) 00:02.1 USB Controller: nVidia Corporation MCP55 USB Controller (rev a2) 00:04.0 IDE interface: nVidia Corporation MCP55 IDE (rev a1) 00:05.0 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:05.1 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:05.2 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:06.0 PCI bridge: nVidia Corporation MCP55 PCI bridge (rev a2) 00:08.0 Bridge: nVidia Corporation MCP55 Ethernet (rev a3) 00:09.0 Bridge: nVidia Corporation MCP55 Ethernet (rev a3) 00:0b.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0c.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0f.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:18.0 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] HyperTransport Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Miscellaneous Control 00:18.4 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Link Control 00:19.0 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] HyperTransport Configuration 00:19.1 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Address Map 00:19.2 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] DRAM Controller 00:19.3 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Miscellaneous Control 00:19.4 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Link Control 03:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA G200e [Pilot] ServerEngines (SEP1) (rev 02) 04:00.0 PCI bridge: NEC Corporation uPD720400 PCI Express - PCI/PCI-X Bridge (rev 06) 04:00.1 PCI bridge: NEC Corporation uPD720400 PCI Express - PCI/PCI-X Bridge (rev 06) 09:00.0 SCSI storage controller: LSI Logic / Symbios Logic SAS1064ET PCI-Express Fusion-MPT SAS (rev 04)

    Read the article

  • Configuring WPA WiFi in Ubuntu 10.10

    - by sma
    I am trying to configure my wireless network on my laptop running Ubuntu 10.10 and am having a bit of difficulty. I am a complete Linux newb, but want to learn it, hence the reason I'm trying to set this up. Here's the vitals: It is a Gateway 600 YG2 laptop. It was previously running Windows XP, but I installed Ubuntu 10.10 in place of it (not a dual boot, I removed XP altogether). I have an old wireless card that I'm trying to resurrect. I haven't really used the card in a couple years, but it seems to still work, I just can't connect to my home's wireless network. The card is a Linksys WPC11 v2.5. When I plug it in, Ubuntu recognizes the network, but won't connect to it. My home network uses WPA encryption and the only connection type that Ubuntu's network manager is giving me is WEP and then it asks for a key -- I have no idea what that key should be. So, basically, I'm asking, is there a way I can instead connect through WPA? I've tried creating a new connection in network manager, but that won't work, it keeps falling back to the WEP connection and asking me for a key. I have tried to install the XP driver using ndiswrapper but I don't know if that's working or not. Is there a way to tell if: A) the card is working as it should B) the correct drivers are installed (again, I installed the XP one using ndiswrapper NET8180.INF, but I'm not sure what to do next) Any help would be appreciated. Thank you.

    Read the article

  • Linux box acting as wireless access point to share the internet connection

    - by Suresh
    A linux machine is connected to internet over two interfaces ppp0 and ppp1 using two modems. Also this machine acts as wireless access point through an interface say, eth0 with ip address 192.168.1.1 and acts as gateway for the connected devices through this network with subnet mask 255.255.255.0 Now is it possible to achieve the following: When any of the connected devices through wireless AP needs internet connection linux machine has to use ppp1 interface for internet. If any of the applications on the linux machine needs internet connection linux machine should use ppp0 interface for the internet. Can this be achieved by adding rules to chains in filter/nat tables? If the kernel routing table has a default rule to route the default traffic through interface ppp0, wil kernel completely ignore ppp1 for internet? PS: new to networking and routing concepts, If the question is not clear leave a comment, will try to give more information.

    Read the article

  • RTNETLINK answers: Invalid argument

    - by LinuxPenseur
    When my system boots up it shows the following message. Bringing up loopback interface: [ OK ] Bringing up interface eth0: RTNETLINK answers: Invalid argument [ OK ] Bringing up interface eth1: RTNETLINK answers: Invalid argument [ OK ] Bringing up interface eth2: RTNETLINK answers: Invalid argument [ OK ] Bringing up interface eth3: RTNETLINK answers: Invalid argument [ OK ] Why is this happening. Normally it does not give the message RTNETLINK answers: Invalid argument I did ifconfig and the output is eth0 Link encap:Ethernet HWaddr 00:00:50:6D:56:B4 inet addr:120.0.10.137 Bcast:120.0.255.255 Mask:255.255.255.0 inet6 addr: fe80::200:50ff:fe6d:56b4/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:3 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 b) TX bytes:214 (214.0 b) Base address:0xa000 eth1 Link encap:Ethernet HWaddr 00:00:50:6D:56:B5 inet addr:121.0.10.137 Bcast:121.0.255.255 Mask:255.255.255.0 inet6 addr: fe80::200:50ff:fe6d:56b5/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:3 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 b) TX bytes:214 (214.0 b) Base address:0xc000 eth2 Link encap:Ethernet HWaddr 00:00:50:6D:56:B6 inet addr:128.0.10.137 Bcast:128.0.255.255 Mask:255.255.255.0 inet6 addr: fe80::200:50ff:fe6d:56b6/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:14 errors:0 dropped:0 overruns:0 frame:0 TX packets:4 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1006 (1006.0 b) TX bytes:396 (396.0 b) Interrupt:16 eth3 Link encap:Ethernet HWaddr 00:00:50:6D:56:B7 inet addr:123.0.10.137 Bcast:123.0.255.255 Mask:255.255.255.0 inet6 addr: fe80::200:50ff:fe6d:56b7/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:10 errors:0 dropped:0 overruns:0 frame:0 TX packets:4 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:728 (728.0 b) TX bytes:396 (396.0 b) Interrupt:17 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:14 errors:0 dropped:0 overruns:0 frame:0 TX packets:14 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:980 (980.0 b) TX bytes:980 (980.0 b) What could be the reason for the message and how to change this to normal? Thanks

    Read the article

  • NTPD issue - syncs then slowly loses ground

    - by ethrbunny
    RHEL 5 workstation. Has been running smoothly for years. I did a 'pup' recently and followed with a nice, cleansing reboot. Afterwards the system had some startup issues: namely MySQL refused to start. It just went "...." for 5-10 minutes before I did another boot and skipped that step (using 'interactive'). This was the only service that didn't wan't to start normally. So now that the system is booted I've found that it doesn't want to stay in sync with the NTP master and after 48 hours is refusing any SSH other than root. NTPD: this service starts normally and gets a lock on 4 servers. Almost immediately it starts to lose ground and now (after 3 days) is almost 40 hours behind. If I stop/start the service it gets the lock, resets the system clock and starts losing ground again. The 'hwclock' is set properly and maintains its time. Login: when I (re)start the ntp server I am able to login normally. I assume this problem is due to losing sync with LDAP. This appears to be verified by LDAP errors in /var/log/messages. Suggestions on where to look? ADDENDA: Tried deleting the 'drift' file. After a bit it gets recreated with 0.000. from /var/log/messages: Jan 17 06:54:01 aeolus ntpdate[5084]: step time server 129.95.96.10 offset 30.139216 sec Jan 17 06:54:01 aeolus ntpd[5086]: ntpd [email protected] Tue Oct 25 12:54:17 UTC 2011 (1) Jan 17 06:54:01 aeolus ntpd[5087]: precision = 1.000 usec Jan 17 06:54:01 aeolus ntpd[5087]: Listening on interface wildcard, 0.0.0.0#123 Disabled Jan 17 06:54:01 aeolus ntpd[5087]: Listening on interface wildcard, ::#123 Disabled Jan 17 06:54:01 aeolus ntpd[5087]: Listening on interface lo, ::1#123 Enabled Jan 17 06:54:01 aeolus ntpd[5087]: Listening on interface eth0, fe80::213:72ff:fe20:4080#123 Enabled Jan 17 06:54:01 aeolus ntpd[5087]: Listening on interface lo, 127.0.0.1#123 Enabled Jan 17 06:54:01 aeolus ntpd[5087]: Listening on interface eth0, 10.127.24.81#123 Enabled Jan 17 06:54:01 aeolus ntpd[5087]: kernel time sync status 0040 Jan 17 06:54:02 aeolus ntpd[5087]: frequency initialized 0.000 PPM from /var/lib/ntp/drift Jan 17 06:54:02 aeolus ntpd[5087]: system event 'event_restart' (0x01) status 'sync_alarm, sync_unspec, 1 event, event_unspec' (0xc010) You can see the 30 second offset. This was after about one minute of operation.

    Read the article

  • Cisco Catalyst 3750 connected to Cisco ASA 5505 and dropping packets

    - by Bo102010
    (Cross posted from Super User per suggestion there) At the office, I have inherited a network that I am still trying to fully comprehend. I have a problem today with a new connection between: A port on a Cisco Catalyst 3750 [WS-C3750G-48TS-S running C3750-IPSERVICESK9-M version 12.2(53)SE1] A port on a Cisco ASA 5505 [ASA Software version 8.3(2)] The 3750 is home to a Vlan that has a few ports assigned to it. interface Vlan3 description Internal network (172.18.160.0/24) ip address 172.18.160.1 255.255.255.0 I have a host (outside of my control) that needs to be in this VLAN (i.e it must have an address 172.18.160.something/24) that also needs to access the Internet. To accomplish this, I ran a link from the Catalyst (Gi1/0/13) to the ASA (Ethernet 0/5). I configured the Catalyst port like so: interface GigabitEthernet1/0/13 description To ASA, 172.18.160.69 switchport access vlan 3 switchport mode access speed 100 duplex full I configured the ASA like so: interface Vlan1 nameif inside security-level 100 ip address 172.18.160.69 255.255.255.0 interface Ethernet0/5 speed 100 duplex full Then I plugged the host into Ethernet 0/4 on the ASA and instructed its owner to make its default gateway 172.18.160.69. I made a NAT rule in the ASA and set up some rules, and it's able to access the Internet without issue. However, I noticed that the Catalyst reports a ton of packets being dropped toward the ASA. Catalyst3750#show interfaces GigabitEthernet 1/0/13 | include counters|drops Last clearing of "show interface" counters 00:28:13 Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 136909347 This is a huge number of drops, since there's not much traffic on this VLAN at all. I tried these things: Make sure speed and duplex agree on both sides (100 Mbps / Full) Set no cdp enable on the Catalyst Gi10/13 Set no keepalive on the Catalyst Gi10/13 Checked for excessive CPU usage on both Checked for excessive traffic on both Am I missing something? Any help would be appreciated.

    Read the article

  • Win7 Domain User Profile- Desktop Icon management best practices request

    - by Doltknuckle
    Here's the situation: We have a large (5,000+ user) organization that is currently using folder redirection to manage the windows desktop icons. This folder is redirected to a network share where we can centrally manage the different sites and such. When a user tries to use a computer when the network is not available, they are unable to use any shortcuts in the Public folder. We only redirect the C:\Users\%username%\Desktop folder. Does anyone have any suggestions of how to go about managing desktop icons? We still want a central location to manage these items, but find a way to keep the system working when the network is unavailable. As a point of clarification, the network rarely goes down. We do have instances where a few computers do not have a network connection. Usually, something is simply unplugged. Since we have multiple sites, the line from a branch to the central office has gone down a few times. This is more of an attempt to maintain a positive end user experience when disconnected from the network.

    Read the article

  • How do I make Linux recognize a new SATA /dev/sda drive I hot swapped in without rebooting?

    - by Philip Durbin
    Hot swapping out a failed SATA /dev/sda drive worked fine, but when I went to swap in a new drive, it wasn't recognized: [root@fs-2 ~]# tail -18 /var/log/messages May 5 16:54:35 fs-2 kernel: ata1: exception Emask 0x10 SAct 0x0 SErr 0x50000 action 0xe frozen May 5 16:54:35 fs-2 kernel: ata1: SError: { PHYRdyChg CommWake } May 5 16:54:40 fs-2 kernel: ata1: link is slow to respond, please be patient (ready=0) May 5 16:54:45 fs-2 kernel: ata1: device not ready (errno=-16), forcing hardreset May 5 16:54:45 fs-2 kernel: ata1: soft resetting link May 5 16:54:50 fs-2 kernel: ata1: link is slow to respond, please be patient (ready=0) May 5 16:54:55 fs-2 kernel: ata1: SRST failed (errno=-16) May 5 16:54:55 fs-2 kernel: ata1: soft resetting link May 5 16:55:00 fs-2 kernel: ata1: link is slow to respond, please be patient (ready=0) May 5 16:55:05 fs-2 kernel: ata1: SRST failed (errno=-16) May 5 16:55:05 fs-2 kernel: ata1: soft resetting link May 5 16:55:10 fs-2 kernel: ata1: link is slow to respond, please be patient (ready=0) May 5 16:55:40 fs-2 kernel: ata1: SRST failed (errno=-16) May 5 16:55:40 fs-2 kernel: ata1: limiting SATA link speed to 1.5 Gbps May 5 16:55:40 fs-2 kernel: ata1: soft resetting link May 5 16:55:45 fs-2 kernel: ata1: SRST failed (errno=-16) May 5 16:55:45 fs-2 kernel: ata1: reset failed, giving up May 5 16:55:45 fs-2 kernel: ata1: EH complete I tried a couple things to make the server find the new /dev/sda, such as rescan-scsi-bus.sh but they didn't work: [root@fs-2 ~]# echo "---" > /sys/class/scsi_host/host0/scan -bash: echo: write error: Invalid argument [root@fs-2 ~]# [root@fs-2 ~]# /root/rescan-scsi-bus.sh -l [snip] 0 new device(s) found. 0 device(s) removed. [root@fs-2 ~]# [root@fs-2 ~]# ls /dev/sda ls: /dev/sda: No such file or directory I ended up rebooting the server. /dev/sda was recognized, I fixed the software RAID, and everything is fine now. But for next time, how can I make Linux recognize a new SATA drive I have hot swapped in without rebooting? The operating system in question is RHEL5.3: [root@fs-2 ~]# cat /etc/redhat-release Red Hat Enterprise Linux Server release 5.3 (Tikanga) The hard drive is a Seagate Barracuda ES.2 SATA 3.0-Gb/s 500-GB, model ST3500320NS. Here is the lscpi output: [root@fs-2 ~]# lspci 00:00.0 RAM memory: nVidia Corporation MCP55 Memory Controller (rev a2) 00:01.0 ISA bridge: nVidia Corporation MCP55 LPC Bridge (rev a3) 00:01.1 SMBus: nVidia Corporation MCP55 SMBus (rev a3) 00:02.0 USB Controller: nVidia Corporation MCP55 USB Controller (rev a1) 00:02.1 USB Controller: nVidia Corporation MCP55 USB Controller (rev a2) 00:04.0 IDE interface: nVidia Corporation MCP55 IDE (rev a1) 00:05.0 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:05.1 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:05.2 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:06.0 PCI bridge: nVidia Corporation MCP55 PCI bridge (rev a2) 00:08.0 Bridge: nVidia Corporation MCP55 Ethernet (rev a3) 00:09.0 Bridge: nVidia Corporation MCP55 Ethernet (rev a3) 00:0a.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0b.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0c.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0d.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0e.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0f.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 00:19.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:19.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:19.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:19.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 03:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA G200e [Pilot] ServerEngines (SEP1) (rev 02) 04:00.0 PCI bridge: NEC Corporation uPD720400 PCI Express - PCI/PCI-X Bridge (rev 06) 04:00.1 PCI bridge: NEC Corporation uPD720400 PCI Express - PCI/PCI-X Bridge (rev 06) Update: In perhaps a dozen cases, we've been forced to reboot servers because hot swap hasn't "just worked." Thanks for the answers to look more into the SATA controller. I've included the lspci output for the problematic system above (hostname: fs-2). I could still use some help understanding what exactly isn't supported hardware-wise in terms of hot swap for that system. Please let me know what other output besides lspci might be useful. The good news is that hot swap "just worked" today on one of our servers (hostname: www-1), which is very rare for us. Here is the lspci output: [root@www-1 ~]# lspci 00:00.0 RAM memory: nVidia Corporation MCP55 Memory Controller (rev a2) 00:01.0 ISA bridge: nVidia Corporation MCP55 LPC Bridge (rev a3) 00:01.1 SMBus: nVidia Corporation MCP55 SMBus (rev a3) 00:02.0 USB Controller: nVidia Corporation MCP55 USB Controller (rev a1) 00:02.1 USB Controller: nVidia Corporation MCP55 USB Controller (rev a2) 00:04.0 IDE interface: nVidia Corporation MCP55 IDE (rev a1) 00:05.0 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:05.1 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:05.2 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:06.0 PCI bridge: nVidia Corporation MCP55 PCI bridge (rev a2) 00:08.0 Bridge: nVidia Corporation MCP55 Ethernet (rev a3) 00:09.0 Bridge: nVidia Corporation MCP55 Ethernet (rev a3) 00:0b.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0c.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0f.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:18.0 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] HyperTransport Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Miscellaneous Control 00:18.4 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Link Control 00:19.0 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] HyperTransport Configuration 00:19.1 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Address Map 00:19.2 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] DRAM Controller 00:19.3 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Miscellaneous Control 00:19.4 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Link Control 03:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA G200e [Pilot] ServerEngines (SEP1) (rev 02) 04:00.0 PCI bridge: NEC Corporation uPD720400 PCI Express - PCI/PCI-X Bridge (rev 06) 04:00.1 PCI bridge: NEC Corporation uPD720400 PCI Express - PCI/PCI-X Bridge (rev 06) 09:00.0 SCSI storage controller: LSI Logic / Symbios Logic SAS1064ET PCI-Express Fusion-MPT SAS (rev 04)

    Read the article

  • Networking problems in VMWare with wireless bridge

    - by Robert Koritnik
    Barebone data: virtualization: VMWare Workstation 6.5 (latest) Host: Windows Server 2008 x64 Guest: Windows Server 2008 x86 Host network adapter: Ethernet (see comment) Host network adapter: Wireless (see comment) Guest ethernet network adapter 1: Bridged VMNet (automatic) Guest ethernet network adapter 2: Host only VMNet comment: my host has LAN and Wifi but only one at the same time. I'm either wired or wireless. Never both. So bridged connection on VM goes either via wire or air. Problem When I'm wirelessly connected on the host and I access internet within VM my connection just gets stalled (not dropped). It doesn't experience any timeout whatsoever, it just stops downloading/communicating. For instance: I start downloading a file with a browser (IE/FF/CR doesn't matter) and I have to pause/restart download when speed drops to 0. I could wait indefinitely but connection won't pick-up automatically. What did I miss in my network configuration? Update 1 I've tested this in various combinations. This works fine when host is connected via Ethernet. But when host is connected via Wifi, the connection on the guest works as previously described. It connects fine. It gets a valid IP from DHCP... Everything is cool as long as you don't start doing some intensive network traffic (ie. download a 2MB file) In this case it starts downloading and stops after a while. Speed just drops to 0B/s... Sometimes it picks up back, sometimes it doesn't. Connection still stays and works. I can ping around with no problem.

    Read the article

  • Windows 8 - no internet connetction to some hosts while VPN is active

    - by HTD
    I use VPN to access the servers at work. When VPN is used, all network traffic to the Internet passes through my company network. It worked without any problems on Windows 7, now on Windows 8 some sites suddenly became inaccessible. Please note - I don't try to connect them over RDP, they are public Internet addresses, outside company network. They are inaccessible using any protocol. Ping returns "General failure.". I know it could be a misconfiguration on my company's server side, but it's very strange, since the same VPN connection used on Windows 7 works properly. What's wrong? Is it a Windows 8 bug, or is there something I could do on my company servers to make VPN work as expected with Windows 8? My company network works on Windows Server 2008 R2 and uses Microsoft TMG firewall. I couldn't find any rules blocking the traffic to mentioned sites, all network traffic for VPN users are passed through for all IPs and protocols. Any clues? UDPATE: Important - one whole day it worked. I hibernated and restarted the computer, connected and disconnected VPN - nothing could break my connection. Today it broke again, and restarting Windows didn't help. And now the solution: route add -p 0.0.0.0 MASK 255.255.255.255 192.168.1.1 Oh, OK, I know what it did, added my default gateway to routing table. But it still didn't work sometimes. So I removed my main network gateway route with: route delete -p 0.0.0.0 MASK 0.0.0.0 192.168.0.1 And added modified with: route add -p 0.0.0.0 MASK 255.255.255.255 192.168.0.1 And it works. Now. But I don't trust this. I don't know what really happened.

    Read the article

< Previous Page | 292 293 294 295 296 297 298 299 300 301 302 303  | Next Page >