Search Results

Search found 23826 results on 954 pages for 'default gateway'.

Page 298/954 | < Previous Page | 294 295 296 297 298 299 300 301 302 303 304 305  | Next Page >

• IPTables masquerading with one NIC

  - by Tuinslak

  Hi, I am running an OpenVPN server with only one NIC. This is my current layout: public.ip > Cisco firewall > lan.ip > OpenVPN server lan.ip = 192.168.22.70 The Cisco firewall forwards the requests to the oVPN server, thus so far everything works and clients are able to connect. However, all clients connected should be able to access 3 networks: lan1: 192.168.200.0 (vpn lan) > tun0 lan2: 192.168.110.0 (office lan) > eth1 (gw 192.168.22.1) lan3: 192.168.22.0 (server lan) > eth1 (broadcast network) So tun0 is mapped to eth1. Iptables output: # iptables-save # Generated by iptables-save v1.4.2 on Wed Feb 16 14:14:20 2011 *filter :INPUT ACCEPT [327:26098] :FORWARD DROP [305:31700] :OUTPUT ACCEPT [291:27378] -A INPUT -i lo -j ACCEPT -A INPUT -i tun0 -j ACCEPT -A INPUT -i ! tun0 -p udp -m udp --dport 67 -j REJECT --reject-with icmp-port-unreachable -A INPUT -i ! tun0 -p udp -m udp --dport 53 -j REJECT --reject-with icmp-port-unreachable -A FORWARD -d 192.168.200.0/24 -i tun0 -j DROP -A FORWARD -s 192.168.200.0/24 -i tun0 -j ACCEPT -A FORWARD -d 192.168.200.0/24 -i eth1 -j ACCEPT COMMIT # Completed on Wed Feb 16 14:14:20 2011 # Generated by iptables-save v1.4.2 on Wed Feb 16 14:14:20 2011 *nat :PREROUTING ACCEPT [302:26000] :POSTROUTING ACCEPT [3:377] :OUTPUT ACCEPT [49:3885] -A POSTROUTING -o eth1 -j MASQUERADE COMMIT # Completed on Wed Feb 16 14:14:20 2011 Yet, clients are unable to ping any ip (including 192.168.200.1, which is the oVPN's IP) When the machine was directly connected to the internet, with 2 NICs, it was quite simply solved with masquerading and adding static routes in the oVPN client's config. However, as masquerading won't accept virtual interfaces (eth0:0, etc) I am unable to get masquerading to work again (and I'm not even sure whether I need virtual interfaces). Thanks. Edit: OpenVPN server: # ifconfig eth1 Link encap:Ethernet HWaddr ba:e6:64:ec:57:ac inet addr:192.168.22.70 Bcast:192.168.22.255 Mask:255.255.255.0 inet6 addr: fe80::b8e6:64ff:feec:57ac/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:6857 errors:0 dropped:0 overruns:0 frame:0 TX packets:4044 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:584046 (570.3 KiB) TX bytes:473691 (462.5 KiB) Interrupt:14 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:334 errors:0 dropped:0 overruns:0 frame:0 TX packets:334 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:33773 (32.9 KiB) TX bytes:33773 (32.9 KiB) tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:192.168.200.1 P-t-P:192.168.200.2 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) ifconfig on a client: # ifconfig eth0 Link encap:Ethernet HWaddr 00:22:64:71:11:56 inet addr:192.168.110.94 Bcast:192.168.110.255 Mask:255.255.255.0 inet6 addr: fe80::222:64ff:fe71:1156/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3466 errors:0 dropped:0 overruns:0 frame:0 TX packets:1838 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:997924 (974.5 KiB) TX bytes:332406 (324.6 KiB) Interrupt:17 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:37847 errors:0 dropped:0 overruns:0 frame:0 TX packets:37847 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:2922444 (2.7 MiB) TX bytes:2922444 (2.7 MiB) tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:192.168.200.30 P-t-P:192.168.200.29 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:689 errors:0 dropped:18 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:0 (0.0 B) TX bytes:468778 (457.7 KiB) wlan0 Link encap:Ethernet HWaddr 00:16:ea:db:ae:86 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:704699 errors:0 dropped:0 overruns:0 frame:0 TX packets:730176 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:520385963 (496.2 MiB) TX bytes:225210422 (214.7 MiB) static routes line at the end of the client's config (I've been playing around with the 192.168.200.0 -- (un)commenting to see if anything changes): route 192.168.200.0 255.255.255.0 route 192.168.110.0 255.255.255.0 route 192.168.22.0 255.255.255.0 route on a vpn client: # route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.200.29 0.0.0.0 255.255.255.255 UH 0 0 0 tun0 192.168.22.0 192.168.200.29 255.255.255.0 UG 0 0 0 tun0 192.168.200.0 192.168.200.29 255.255.255.0 UG 0 0 0 tun0 192.168.110.0 192.168.200.29 255.255.255.0 UG 0 0 0 tun0 192.168.110.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 0.0.0.0 192.168.110.1 0.0.0.0 UG 0 0 0 eth0 edit: Weirdly enough, if I set push "redirect-gateway def1" in the server config, (and thus routes all traffic through VPN, which is not what I want), it seems to work.

  Read the article

• Disabling at application level a nic (network interface) on Windows

  - by Leandro

  How can I disable at application level a network interface? The main question is this: If I disable the nic trough wmic (win7) or devcon (XP), the "plug and play" of a wired nic doesn't work any more. For example, if the user put the cable on a disabled nic, the OS doesn't know about it. So I need to persist the enable condition but disabling the networking like a disable nic. There's some API, network configuration (routing, changing ip, changing gateway, any), .NET Framework resource (Only NetFramework 2.0) or do you can think in any workaround to do this? Suggest and ideas also will be treated as a solution. Thanks and kind regards.

  Read the article

• How Can I Make Apache Stop Serving ALL Unknown File Types (like .php~)?

  - by user223304

  I am coming from IIS and moving to Apache and recently found out that Apache by default serves up files of an unknown file extension as PURE TEXT. This can be an issue if a user uses certain programs that back up .php files as .php~. Then the .php~ file becomes completely readable by simply navigating to it in a browser. To make matters worse these .php~ files are often considered 'hidden' in the linux environment from the user so some may not even know they exist. Bots have been created around this fact that scour the internet looking for popular file name backups and extracting potentially secure info from them. I already know how to stop serving up .php~ files or any specific file extensions. I also know not to use any editors that would save backup files like this. My question is, how can I stop this default Apache behavior of serving up ANY non-MIME file type at all? I just don't like the this behavior and would like to stop it. I don't want it serving up .aspx~, .html~, .bob, .carl, no extension or anything else that is not a real MIME type. I know that I can probably go and use a directive to first Deny access to all file types. Then add the ones I want to serve out one by one. But I'm wondering if there's an easier/quicker way. Thanks for any help.

  Read the article

• CentOS: eth0 not starting on boot

  - by Cameron Aziz

  Whenever I reboot a CentOS Hyper-V VM, eth0 does not start automatically. All I need to do is perform ifup eth0 and all is fixed, but that isn't feasible from ssh! I am starting in runlevel 3. After I perform ifup eth0 on the console: [root@localhost ~]# ifconfig eth0 Link encap:Ethernet HWaddr 00:15:5D:2B:2B:07 inet addr:10.10.0.3 Bcast:10.10.0.255 Mask:255.255.255.0 inet6 addr: fe80::215:5dff:fe2b:2b07/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:34 errors:0 dropped:0 overruns:0 frame:0 TX packets:49 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4656 (4.5 KiB) TX bytes:6399 (6.2 KiB) Interrupt:9 Base address:0xa000 [root@localhost ~]# cat /etc/sysconfig/network-scripts/ifcfg-eth0 DEVICE=eth0 BOOTPROTO=none IPADDR=10.10.0.3 NETMASK=255.255.255.0 GATEWAY=10.10.0.1 USERCTL=no ONBOOT=yes [root@localhost ~]# chkconfig --list | grep network network 0:off 1:off 2:on 3:on 4:on 5:on 6:off

  Read the article

• Mounting a VirtualBox shared folder on boot with fstab in OpenSuse 11.3

  - by ccook

  I have followed the steps found here, however, the share is not mounted on boot. The share will mount if i run 'mount -a' after booting. Why would the share not mount on boot? 1 - Set up a Virtual Machine and install OpenSUSE 11.2 2 - Create a shared folder on host (HostFolder) 3 - Setup the shared folder in Virtualbox Via the Virtual Machine details or via Devices Shared Folders... 4 - Install dependencies for running the Virtualbox installer You need to install the right development kernelpackage for your machinetype (use 'zypper search -i kernel' to see what's installed) sudo zypper install make gcc kernel-source kernel-hosttype/default-devel 5 - Run the Virtual Machine and go to Devices Guest Additions This mounts an iso image in your OpenSUSE guest. 6 - Open a root terminal and run cd /usr/src/linux make oldconfig && make prepare && make scripts && make dep cp ../linux-obj/$HOSTTYPE/default/Module.symvers . make prepare A commenter on previously mentioned thread says this step is unnecessary but it doesn't work without on my system. I suggest trying step 7 first and returning to step 6 if that fails. * 7 - Run ./VirtualboxLinux yourhosttype .run from the mounted iso image. 8 - Create shared folder in OpenSUSE (GuestFolder) 9 - Test with sudo mount -t vboxsf HostFolder /home/user/GuestFolder It works? Great! Let's set up the system so it automounts for your regular useraccount instead of root-only access. 10 - Add this line to /etc/fstab HostFolder /home/user/GuestFolder vboxsf defaults,uid=1000,gid=1000 0 0 11 - It works for me but if it still doesn't automount after a reboot; sudo mount -a

  Read the article

• chkconfig creating service symlinks with the wrong order

  - by Robert

  On RHEL 6.3, I have a system service that should be starting after postgresql and httpd (order 64 and 85, respectively), but chkconfig always places it at order 50. I tried an experiment on a CentOS 6.0 virtual machine to make sure I understood the LSB stanza syntax. I created /etc/init.d/foo, owner root, permissions 755, with this text: ### BEGIN INIT INFO # Provides: foo # Required-Start: postgresql httpd # Default-Start: 2 3 4 5 # Default-Stop: 0 1 6 # Description: Foo init script ### END INIT INFO And then ran chkconfig --add foo. Result: /etc/rc5.d/S86foo is created, as expected. (The other runlevels are also as expected.) I repeated the exact same experiment on the RHEL machine, and it created /etc/rc5.d/S50foo instead. I can't see anything different between the two that would lead to different results. Both machines have postgresql and httpd starting at the same orders and runlevels. Any thoughts? I could just use # chkconfig: 2345 86 50, or manually rename the service symlinks to the correct order, but I'm trying to document an install process for later users, and I want to know how to do it right and understand why it's not working as expected.

  Read the article

• nginx: how do I add new site/server_name in nginx?

  - by Neo

  I'm just starting to explore Nginx on my Ubuntu 10.04. I installed Nginx and I'm able to get the "Welcome to Nginx" page on localhost. However I'm not able to add a new server_name, even when I make the changes in site-available/default file. Tried reloading/restarting Nginx, but nothing works. One interesting observation. "http://mycomputername" in browser works. So somehow there is a command like 'server_name $hostname' somewhere over-riding my rule. File: sites-available/mine.enpass server { listen 80; server_name mine.enpass ; access_log /var/log/nginx/localhost.access.log; location / { root /var/www/nginx-default; index index.html index.htm; } } File: nginx.confg user www-data; worker_processes 1; error_log /var/log/nginx/error.log; pid /var/run/nginx.pid; events { worker_connections 1024; # multi_accept on; } http { include /etc/nginx/mime.types; access_log /var/log/nginx/access.log; sendfile on; #tcp_nopush on; #keepalive_timeout 0; keepalive_timeout 65; tcp_nodelay on; gzip on; gzip_comp_level 2; gzip_proxied any; gzip_types text/plain text/css application/x-javascript text/xml application/xml application/xml+rss text/javascript; gzip_disable "MSIE [1-6]\.(?!.*SV1)"; include /etc/nginx/conf.d/*.conf; include /etc/nginx/sites-enabled/*; }

  Read the article

• Cascading switches: uplink to uplink?

  - by wuckachucka

  I'm a bit confused as to why I haven't seen any references online to using Switch A's uplink port (1Gbps, 24-port 10/100) to connect to Switch B's uplink port: everything I've seen -- including documentation, forums, articles, etc. -- has Switch A's uplink port going to one of Switch B's 10/100 access ports. As I understand it, the Uplink port (besides greater speed normally) is no different than another port except that it's "internally crossed-over" so that you can use a straight cable with it. I've also seen documentation on using the uplink port to connect a switch to a gateway router, or even a server, as it provides greater bandwidth than the access ports, but yet not sure why nobody seems to be cross-uplinking, even when there's 2 uplink ports available on some higher-end switches. Switch in question is Linksys SRW224P (x2). Am I missing something?

  Read the article

• Weird behaviour with OpenVPN: can not connect to a few websites

  - by Gaby Solis

  My OpenVPN server is Ubuntu 10.04.4 LTS and openvpn version is 2.x My client is on Win 7. He can access most sites but not Youtube, Facebook, Twitter, groups.google.com, etc My server.conf is: local x.x.x.x port 1194 proto udp dev tun ca /etc/openvpn/keys/ca.crt cert /etc/openvpn/keys/server.crt key /etc/openvpn/keys/server.key dh /etc/openvpn/keys/dh1024.pem server 10.8.0.0 255.255.255.0 push "redirect-gateway def1" push "dhcp-option DNS 8.8.8.8" client-to-client keepalive 10 120 comp-lzo persist-key persist-tun status /etc/openvpn/keys/openvpn-status.log verb 4 I can access Youtube etc using SSH Tunnel + SOCKS Proxy, and the Ubuntu server can access all sites. so nothing is wrong with the Ubuntu server. With little information I can provide, I am not looking for a quck solution. How can I debug?

  Read the article

• Connecting two pcs through cable, at the same time as wireless

  - by Steffen

  I've got 2 pcs setup with WLAN - however when I copy files between the machines it takes forever (obviously, since I run 801.11g). So I thought, why not just connect them directly with a cable (my wireless router is the other end of the house, that's why I don't use cables to that) However how should I configure the LAN connection on each machine, so I can use it for transferring files between them, whilst using my WLAN to access the Internet ? I was thinking about letting one machine be gateway, but then Windows pops up with a lot of warnings (basically it says this won't work when you're using two disjoint networks) And now I'm at a loss as to what to try.

  Read the article

• Management VLAN Cisco Catalyst

  - by cha789

  I have configured a couple of VLANs on a Cisco Catalyst switch, i will put all the ports that clients is connected to, into these VLANs. I want to configure the native VLAN [vlan 1] as management VLAN so i can use a telnet client to connect to the switch. How can i block all but one specific IP-address to telnet into the switch? As i understand vlan 1 has many task regarding different protocols and i do not want to break that but only allow one specific IP-address to connect to the switch with a telnet client [actually the gateway ip address of the switch].

  Read the article

• Traffic shaping on Linux with HTB: weird results

  - by DADGAD

  I'm trying to have some simple bandwidth throttling set up on a Linux server and I'm running into what seems to be very weird stuff despite a seemingly trivial config. I want to shape traffic coming to a specific client IP (10.41.240.240) to a hard maximum of 75Kbit/s. Here's how I set up the shaping: # tc qdisc add dev eth1 root handle 1: htb default 1 r2q 1 # tc class add dev eth1 parent 1: classid 1:1 htb rate 75Kbit # tc class add dev eth1 parent 1:1 classid 1:10 htb rate 75kbit # tc filter add dev eth1 parent 1:0 protocol ip prio 1 u32 match ip dst 10.41.240.240 flowid 1:10 To test, I start a file download over HTTP from the said client machine and measure the resulting speed by looking at Kb/s in Firefox. Now, the behaviour is rather puzzling: the DL starts at about 10Kbyte/s and proceeds to pick up speed until it stabilizes at about 75Kbytes/s (Kilobytes, not Kilobits as configured!). Then, If I start several parallel downloads of that very same file, each download stabilizes at about 45Kbytes/s; the combined speed of those downloads thus greatly exceeds the configured maximum. Here's what I get when probing tc for debug info [root@kup-gw-02 /]# tc -s qdisc show dev eth1 qdisc htb 1: r2q 1 default 1 direct_packets_stat 1 Sent 17475717 bytes 1334 pkt (dropped 0, overlimits 2782 requeues 0) rate 0bit 0pps backlog 0b 12p requeues 0 [root@kup-gw-02 /]# tc -s class show dev eth1 class htb 1:1 root rate 75000bit ceil 75000bit burst 1608b cburst 1608b Sent 14369397 bytes 1124 pkt (dropped 0, overlimits 0 requeues 0) rate 577896bit 5pps backlog 0b 0p requeues 0 lended: 1 borrowed: 0 giants: 1938 tokens: -205561 ctokens: -205561 class htb 1:10 parent 1:1 prio 0 **rate 75000bit ceil 75000bit** burst 1608b cburst 1608b Sent 14529077 bytes 1134 pkt (dropped 0, overlimits 0 requeues 0) **rate 589888bit** 5pps backlog 0b 11p requeues 0 lended: 1123 borrowed: 0 giants: 1938 tokens: -205561 ctokens: -205561 What I can't for the life of me understand is this: how come I get a "rate 589888bit 5pps" with a config of "rate 75000bit ceil 75000bit"? Why does the effective rate get so much higher than the configured rate? What am I doing wrong? Why is it behaving the way it is? Please help, I'm stumped. Thanks guys.

  Read the article

• CentOS iscsi initiator has session but there is no block device

  - by jcalfee314

  I have installed the scsi-target-utils package on CentOS and I used it to perform a discovery. The discovery did give me an active session. I restarted the iscsi service but I do not see any new devices (fdisk -l). I see in /var/log/messages that my connection is operational now. I'm not sure how to debug this further. Can someone direct me into fixing this? discovery: iscsiadm -m discovery -t sendtargets -p 192.168.0.155 returns: 192.168.0.155:3260,-1 iqn.2009-02.com.twinstrata:cloudarray:sn-1d07c1b62d4ec8f3 Just to verify it actually worked: iscsiadm -m session returns tcp: [1] 192.168.0.155:3260,1 iqn.2009-02.com.twinstrata:cloudarray:sn-1d07c1b62d4ec8f3 restarting as the directions say to do: service iscsi restart output written to /var/log/message Stopping iscsi: Sep 20 12:14:22 localhost kernel: connection1:0: detected conn error (1020) [ OK ] Starting iscsi: Sep 20 12:14:22 localhost kernel: scsi1 : iSCSI Initiator over TCP/IP Sep 20 12:14:22 localhost iscsid: Connection1:0 to [target: iqn.2009-02.com.twinstrata:cloudarray:sn-1d07c1b62d4ec8f3, portal: 192.168.0.155,3260] through [iface: default] is shutdown. Sep 20 12:14:22 localhost iscsid: Could not set session2 priority. READ/WRITE throughout and latency could be affected. [ OK ] [root@db iscsi]# Sep 20 12:14:23 localhost iscsid: Connection2:0 to [target: iqn.2009-02.com.twinstrata:cloudarray:sn-1d07c1b62d4ec8f3, portal: 192.168.0.155,3260] through [iface: default] is operational now Ran a login command: iscsiadm -m node -T iqn.2009-02.com.twinstrata:cloudarray:sn-1d07c1b62d4ec8f3 -p 192.168.0.155 -l No errors, no logging occurred. Next I compared the output from "fdisk -l|egrep dev" both with the iscsi session and without. There is no difference. I suppose I could just look in /etc/mtab. Any ideas on how I can get an iscsi device?

  Read the article

• Plesk: Spamassassin ignores emails to redirected accounts

  - by Mat

  When I set up email redirects within Plesk 9.5, Spamassassin ignores all emails sent to the redirected address and only scans emails that are sent directly to the address which has a mailbox. Steps to reproduce Set up two mail accounts: [email protected] as a proper email account with a mailbox and [email protected] with all emails redirected to [email protected]. (It doesn't make a difference, if [email protected] has a mailbox enabled or not.) [email protected] -> [email protected] Set up the spam filter on both accounts. I set mine to delete spam right away, but you can just keep the default ("mark as spam"). Now, when you send an emails to [email protected], it will have Spamassassins tags in the email header, but when you send emails to [email protected], they will end up in the same mailbox but will have no spamassassin tags in the emails header and they will not be scanned. Other notes I am using Plesk 9.5.4 on Ubuntu 8.04 LTS with the default Qmail. I've observed this bug since Plesk 8, but I can't stand it any more and would appreciate any hack or fix.

  Read the article

• What's the best way to run Drupal and Django sites behind the same Varnish server?

  - by Alexis Bellido

  I have a high traffic website running with Drupal and Apache, five web servers behind a Varnish server load balancing. Let's say this site is example.com. I'm using five backends and a director like this in my default.vcl: director balancer round-robin { { .backend = web1; } { .backend = web2; } { .backend = web3; } { .backend = web4; } { .backend = web5; } } Now I'm working on a new Django project that will be a new section of this site running on example.com/new-section. After checking the documentation I found I can do something like this: sub vcl_recv { if (req.url ~ "^/new-section/") { set req.backend = newbackend; } else { set req.backend = default; } } That is, using a different backend for a subdirectory /new-section under the same domain. My question is, how do I make something like this work with my director and load balancing setup? I'm probably going to run two or more web servers (backends) with my new Django project, each one with a mix of Gunicorn, Nginx, and a few Python packages, and would like to put all of those in their own Varnish director to load balance. Is it possible to do use the above approach to decide which director to use?, like this: sub vcl_recv { if (req.url ~ "^/new-section/") { set req.director = newdirector; } else { set req.director = balancer; } } All suggestions welcome. Thanks!

  Read the article

• Why did my laptop turn off?

  - by darenw

  Normally I can slip my running laptop into a backpack, go somewhere, and if it's no more than about half an hour later, it'll still be running. At the destination I plug in the AC power unit and all is well. I run it off of the AC unit before and after the trip, have the screen at less than full backlight brightness, and don't have any peripherals that burn power. Sometimes the wireless switch accidentally slides in the backpack, and that causes extra power to be used and the laptop dies before I reach the destination. Sad, but so be it. But sometimes the wireless switch is off, I've reached the destination in less than 30 minutes (typically 10-20 min), and I know the battery was fully charged, yet the machine is off. Is there a way to determine, after the fact, why the machine shut itself off? I'm running Linux on a fairly powerful Gateway with 4GB RAM, fancy nvidia graphics, dual core cpu, chosen more for number crunching power than battery life, but should last easily for half an hour if not an hour.

  Read the article

• CentOS Latency High Troubleshooting

  - by Sarah Weinberger

  I have two CentOS servers connected via a 10 Gb fiber optic cable with a network emulator connected between them. All three units sit on a desk in the lab. There is also a regular 1 Gbit Ethernet cable connected to each of the machines, which provide internet connectivity. When I set the latency to something roughly below 30 ms, all is fine. When the latency gets to 70ms and above, and definitely 130ms, the network layer suspends. For instance, if I set the latency (delay) to 70ms, then launching TeamViewer (or any other application that uses network connectivity) never happens or does not work. There is no timeout message, simply no response. I have to lower to latency back down to zero to see any response and have the box start working. What is the problem and how would I go about fixing it? It seems to me some sort of setting in Linux causes one of the CentOS networking drivers to sit in an infinite loop or something. eth0 is the connection to the internet, all settings are default eth2 is the 10 Gbit fiber optic connection to the other computer with the MTU set to 9600 with all other parameters at default values.

  Read the article

• few basic questions on webhosting (namservers & dns records)

  - by claws

  I bought a domain name on name.com & I want to use free webhosting on 110mb.com By default name.com integrates services of Google apps. Name server entries are ns1.name.com ns2.name.com ns3.name.com ns4.name.com When I registered on 110mb.com it gave me two addresses ns1.110mb.com ns2.110mb.com This is where I'm lost. The concept is that "Domain name should point to an address of the server where the website is hosted" right? Then why are these 4 entires by default. How exactly is it working? should I remove these 4 and then add 110mb.com servers or just append 110mb.com server addresses to name.com ones. I would like to use google apps. If I change these name server addresses would that remove google apps? I especially want to use email service of google. And I really don't understand what is CNAME, MX, or something something. I want to learn about these stuff & how it exactly works. When I search for webhost tutorial. I'm unable to find any fruitful results.

  Read the article

• IPv6 Routing / Subnetting

  - by nappo

  Recently I have installed Citrix Xen Server 6.2 on a machine. My Provider (Hetzner) gave me the IPv6 Subnet 2a01:4f8:200:xxxx::/64. Followed an article in the providers wiki (1) i got it working and can assign IPs to my guests (CentOS). However i can't assign a second IP to a single guest - it will result in a timeout. I'm not very familiar with IPv6 routing / subnetting - any help or tips for further troubleshooting is welcome! My Setup: XenServer 6.2 IPv6: 2a01:4f8:200:xxxx::2/112 ip -6 route: 2a01:4f8:200:xxxx::/112 dev xenbr0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 0 fe80::1 dev xenbr0 metric 1024 mtu 1500 advmss 1440 hoplimit 0 default via fe80::1 dev xenbr0 metric 1024 mtu 1500 advmss 1440 hoplimit 0 Guest 1 IPv6: 2a01:4f8:200:xxxx::3/64 IPv6: 2a01:4f8:200:xxxx::4/64 ip -6 route: 2a01:4f8:200:xxxx::/64 dev eth0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 dev eth0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 default via fe80::1 dev eth0 metric 1 mtu 1500 advmss 1440 hoplimit 4294967295 Guest 2 IPv6: 2a01:4f8:200:xxxx::5/64 Guest 1 IPv6 is working fine, Guest 2 too. As suggested by the wiki article (1) i split my /64 network into a /112. Is it right to set the host /112 and the guests /64? Why is that?

  Read the article

• Crossover LAN connection between Ubuntu And Windows 7 is not working

  - by brett

  my question is closely related to: How do I connect Ubuntu 10.04 and Windows 7 with an Ethernet cable? What I am after is: Windows 7-------wireless-----\ Wifi router Ubuntu 10.04----wireless-----/ Windows 7-------wireless-----\ | cross_over_cable Wifi router | Ubuntu 10.04----wireless-----/ What I did was On Windows edit system32\drivers\etc\hosts Add the following line: 192.168.253.2 my_ubuntu_computer_name_&-wired //?not sure if this is right On Ubuntu: sudo gedit /etc/hosts Add the following line: 192.168.253.1 my_pc_computer_name&-wired //?not sure if this is right and then Ubuntu 12.04 as the host Right click on the Network Manager applet, click Edit Connections... In the Wired tab, click Auto eth0, then click Edit... In the IPv4 Settings tab, change Method: to Shared to other computers. Click Apply and enter your password when it asks you. Close everything and reboot. Plug the Ethernet cable into both computers. But, I can connect to my windows network folders from ubuntu via wifi I can't connect to my ubuntu network folders from windows via wifi(in fact this bit was working before - so my wifi connection is worse) my ubuntu Auto Ethernet seems to be on From Ubuntu eth0 Link encap:Ethernet HWaddr 00:11:2f:f3:43:8d inet addr:10.42.0.1 Bcast:10.42.0.255 Mask:255.255.255.0 inet6 addr: fe80::211:2fff:fef3:438d/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:172 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:27279 (27.2 KB) Interrupt:19 Base address:0xe400 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:1147 errors:0 dropped:0 overruns:0 frame:0 TX packets:1147 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:94380 (94.3 KB) TX bytes:94380 (94.3 KB) wlan0 Link encap:Ethernet HWaddr 00:03:c9:e9:6f:bf inet addr:10.1.1.7 Bcast:10.1.1.255 Mask:255.255.255.0 inet6 addr: fe80::203:c9ff:fee9:6fbf/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:13186 errors:0 dropped:0 overruns:0 frame:0 TX packets:12187 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1598882 (1.5 MB) TX bytes:1189555 (1.1 MB) From Windows: Windows IP Configuration Ethernet adapter Bluetooth Network Connection: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Wireless LAN adapter Wireless Network Connection: Connection-specific DNS Suffix . : BoB Link-local IPv6 Address . . . . . : fe80::ecf7:c445:3725:b9c1%12 IPv4 Address. . . . . . . . . . . : 10.1.1.4 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 10.1.1.1 Tunnel adapter Local Area Connection* 15: Connection-specific DNS Suffix . : IPv6 Address. . . . . . . . . . . : 2001:0:4137:9e76:1423:3ae3:f5fe:fefb Link-local IPv6 Address . . . . . : fe80::1423:3ae3:f5fe:fefb%23 Default Gateway . . . . . . . . . : :: Tunnel adapter isatap.BoB: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : BoB Tunnel adapter isatap.{D0C8EBA1-335D-4620-8570-6C36E8786D72}: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . :

  Read the article

• How to cache authentication in Linux using PAM/Kerberos authentication (for CVS)?

  - by Calonthar

  We have several Linux servers that authenticate Linux user passwords on our Windows Active Directory Server using PAM and Kerberos 5. The Linux distro we use is CentOS 6. On one system, we have several Version Control Systems like CVS and Subversion, both of which authenticate users throug PAM, such that users can use their normal Unix resp. Windows AD accounts. Since we started using Kerberos for password authentication, we experienced that CVS on a client machine is often much slower in establishing a connection. CVS authenticates the user on every request (eg. cvs diff, log, update...). Is is possible to cache the credentials that kerberos uses, sucht that is does not need to ask the Windows AD server every time a user executes a cvs action? Our PAM config /etc/pam.d/system-auth looks like the following: auth required pam_env.so auth sufficient pam_unix.so nullok try_first_pass auth requisite pam_succeed_if.so uid >= 500 quiet auth sufficient pam_krb5.so use_first_pass auth required pam_deny.so account required pam_unix.so broken_shadow account sufficient pam_succeed_if.so uid < 500 quiet account [default=bad success=ok user_unknown=ignore] pam_krb5.so account required pam_permit.so password requisite pam_cracklib.so try_first_pass retry=3 password sufficient pam_unix.so md5 shadow nullok try_first_pass use_authtok password sufficient pam_krb5.so use_authtok password required pam_deny.so session optional pam_keyinit.so revoke session required pam_limits.so session [success=1 default=ignore] pam_succeed_if.so service in crond quiet use_uid session required pam_unix.so session optional pam_krb5.so

  Read the article

• "Enter/Return" Key with Word Mobile on Windows Mobile

  - by Maarx

  Some of our employees are using PDAs running Windows Mobile. I wish I could provide more data regarding versions, but frankly these things aren't my jurisdiction. Someone's simply come to me looking for what they thought would be a quick fix. They're using Word Mobile and the barcode scanner to record large volumes of data. The scanner's default action is to insert the scanned text exactly as if it had been input with the keyboard, and puts a newline at the end. That's great, because it's exactly what we need it to do: separate data with newlines. The issue comes when system can't read the barcode, and the employee has to type in the data by hand. They've discovered a very peculiar quirk of Mobile applications: pressing the hardware Enter/Return key on the keyboard appears to save and exit the application. How do we change this behavior? They've realized that using the stylus to "click" the virtual on-screen keyboard's Enter/Return key will add the necessary newline, but it's a huge inconvenience for them. How do I fix the default behavior of the Enter/Return key for Word Mobile to instead insert a newline?

  Read the article

• Unattended Kickstart Install

  - by Eric

  I've looked around quite a bit and have seen similar setup and questions, but none seem to work for me. I'm using the following command to create a custom ISO: /usr/bin/livecd-creator --config=/usr/share/livecd-tools/test.ks --fslabel=TestAppliance --cache=/var/cache/live This works great and it creates the ISO with all of the packages and configs I want on it. My issue is that I want the install to be unattended. However, every time I start the CD, it asks for all of the info such as keyboard, time zone, root password, etc. These are my basic settings I have in my kickstart script prior to the packages section. cdrom install autopart autostep xconfig --startxonboot rootpw testpassword lang en_US.UTF-8 keyboard us timezone --utc America/New_York auth --useshadow --enablemd5 selinux --disabled services --enabled=iptables,rsyslog,sshd,ntpd,NetworkManager,network --disabled=sendmail,cups,firstboot,ip6tables clearpart --all So after looking around, I was told that I need to modify my isolinux.cfg file to either do "ks=http://X.X.X.X/location/to/test.ks" or "ks=cdrom:/test.ks". I've tried both methods and it still forces me to go through the install process. When I tail the apache logs on the server, I see that the ISO never even tries to get the file. Below are the exact syntax I'm trying on my isolinux.cfg file. label http menu label HTTP kernel vmlinuz0 append initrd=initrd0.img ks=http://192.168.56.101/files/test.ks ksdevice=eth0 label localks menu label LocalKS kernel vmlinuz0 append initrd=initrd0.img ks=cdrom:/test.ks label install0 menu label Install kernel vmlinuz0 append initrd=initrd0.img root=live:CDLABEL=PerimeterAppliance rootfstype=auto ro liveimg liveinst noswap rd_NO_LUKS rd_NO_MD rd_NO_DM menu default EOF_boot_menu The first 2 give me a "dracut: fatal: no or empty root=" error until I give it a root= option and then it just skips the kickstart completely. The last one is my default option that works fine, but just requires a lot of user input. Any help would be greatly appreciated.

  Read the article

• BugZilla XML RPC Interface

  - by Damo

  I am attempting to setup BugZilla to receive but reports from another system using the XML-RPC interface. BugZilla works fine on its own with its own interface. When I attempt to test the XML-RPC functionality by accessing "xmlrpc.cgi" in my browser I get the error: The XML-RPC Interface feature is not available in this Bugzilla at C:\BugZilla\xmlrpc.cgi line 27 main::BEGIN(...) called at C:\BugZilla\xmlrpc.cgi line 29 eval {...} called at C:\BugZilla\xmlrpc.cgi line 29 Following this I install test-taint package from the default perl repository, this installs version 1.04. Re-running "xmlrpc.cgi" gives me an IIS error: 502 - Web server received an invalid response while acting as a gateway or proxy server. There is a problem with the page you are looking for, and it cannot be displayed. When the Web server (while acting as a gateway or proxy) contacted the upstream content server, it received an invalid response from the content server. So I run the checksetup.pl which inform me that: Use of uninitialized value in open at C:/Perl/site/lib/Test/Taint.pm line 334, <DATA> line 558. Installing Test-Taint from CPAN is the same. I assume XML-RPC is relent on Test-Taint, but Test-Taint doesn't seem to run correctly. If I ignore this error and attempt to invoke "bz_webservice_demo.pl" to add an entry the script times out. How can I get the XML-RPC / Test-Taint function working ? Current Setup: IIS7.5 on Windows Server 2008 Bugzilla 4.2.2 Perl 5.14.2 C:\BugZilla>perl checksetup.pl Set up gcc environment - 3.4.5 (mingw-vista special r3) * This is Bugzilla 4.2.2 on perl 5.14.2 * Running on Win2008 Build 6002 (Service Pack 2) Checking perl modules... Checking for CGI.pm (v3.51) ok: found v3.59 Checking for Digest-SHA (any) ok: found v5.62 Checking for TimeDate (v2.21) ok: found v2.24 Checking for DateTime (v0.28) ok: found v0.76 Checking for DateTime-TimeZone (v0.79) ok: found v1.48 Checking for DBI (v1.614) ok: found v1.622 Checking for Template-Toolkit (v2.22) ok: found v2.24 Checking for Email-Send (v2.16) ok: found v2.198 Checking for Email-MIME (v1.904) ok: found v1.911 Checking for URI (v1.37) ok: found v1.59 Checking for List-MoreUtils (v0.22) ok: found v0.33 Checking for Math-Random-ISAAC (v1.0.1) ok: found v1.004 Checking for Win32 (v0.35) ok: found v0.44 Checking for Win32-API (v0.55) ok: found v0.64 Checking available perl DBD modules... Checking for DBD-Pg (v1.45) ok: found v2.18.1 Checking for DBD-mysql (v4.001) ok: found v4.021 Checking for DBD-SQLite (v1.29) ok: found v1.33 Checking for DBD-Oracle (v1.19) ok: found v1.30 The following Perl modules are optional: Checking for GD (v1.20) ok: found v2.46 Checking for Chart (v2.1) ok: found v2.4.5 Checking for Template-GD (any) ok: found v1.56 Checking for GDTextUtil (any) ok: found v0.86 Checking for GDGraph (any) ok: found v1.44 Checking for MIME-tools (v5.406) ok: found v5.503 Checking for libwww-perl (any) ok: found v6.02 Checking for XML-Twig (any) ok: found v3.41 Checking for PatchReader (v0.9.6) ok: found v0.9.6 Checking for perl-ldap (any) ok: found v0.44 Checking for Authen-SASL (any) ok: found v2.15 Checking for RadiusPerl (any) ok: found v0.20 Checking for SOAP-Lite (v0.712) ok: found v0.715 Checking for JSON-RPC (any) ok: found v0.96 Checking for JSON-XS (v2.0) ok: found v2.32 Use of uninitialized value in open at C:/Perl/site/lib/Test/Taint.pm line 334, <DATA> line 558. Checking for Test-Taint (any) ok: found v1.04 Checking for HTML-Parser (v3.67) ok: found v3.68 Checking for HTML-Scrubber (any) ok: found v0.09 Checking for Encode (v2.21) ok: found v2.44 Checking for Encode-Detect (any) not found Checking for Email-MIME-Attachment-Stripper (any) ok: found v1.316 Checking for Email-Reply (any) ok: found v1.202 Checking for TheSchwartz (any) not found Checking for Daemon-Generic (any) not found Checking for mod_perl (v1.999022) not found Checking for Apache-SizeLimit (v0.96) not found *********************************************************************** * OPTIONAL MODULES * *********************************************************************** * Certain Perl modules are not required by Bugzilla, but by * * installing the latest version you gain access to additional * * features. * * * * The optional modules you do not have installed are listed below, * * with the name of the feature they enable. Below that table are the * * commands to install each module. * *********************************************************************** * MODULE NAME * ENABLES FEATURE(S) * *********************************************************************** * Encode-Detect * Automatic charset detection for text attachments * * TheSchwartz * Mail Queueing * * Daemon-Generic * Mail Queueing * * mod_perl * mod_perl * * Apache-SizeLimit * mod_perl * *********************************************************************** COMMANDS TO INSTALL OPTIONAL MODULES: Encode-Detect: ppm install Encode-Detect TheSchwartz: ppm install TheSchwartz Daemon-Generic: ppm install Daemon-Generic mod_perl: ppm install mod_perl Apache-SizeLimit: ppm install Apache-SizeLimit Reading ./localconfig... OPTIONAL NOTE: If you want to be able to use the 'difference between two patches' feature of Bugzilla (which requires the PatchReader Perl module as well), you should install patchutils from: http://cyberelk.net/tim/patchutils/ Checking for DBD-mysql (v4.001) ok: found v4.021 Checking for MySQL (v5.0.15) ok: found v5.5.27 WARNING: You need to set the max_allowed_packet parameter in your MySQL configuration to at least 3276750. Currently it is set to 3275776. You can set this parameter in the [mysqld] section of your MySQL configuration file. Removing existing compiled templates... Precompiling templates...done. checksetup.pl complete.

  Read the article

• Why does Google Chrome ignore "last_known_google_url" property in "Local State" file?

  - by Peter Sivák

  I want to force my Google Chrome web browser (version 21.0.1180.89, 64-bit) to use non-localized search (thus google in english) through address bar, using the default Google search engine. To achieve that, I have to change value of the property last_known_google_url to https://www.google.com/?hl=en& in Local State file (for instance on Linux, the full path to the file is ~/.config/google-chrome/Local State). In that file, there should be the property: "browser": { "last_known_google_url": but it is not. Even if I add there the property, it has no impact on search - Google Chrome does not use the property and still searches in localized version. Another option is to put the property to Preferences file (for instance on Linux, the full path to the file is ~/.config/google-chrome/Default/Preferences) - which works perfectly when I start Google Chrome and do some search - but just after that, the property (actually the whole Preferences file) is overriden, so "the most important" trailing part ?hl=en& of the property value is removed - and without it, the non-localized search does not work anymore. Why does Google Chrome ignore last_known_google_url property in Local State file?

  Read the article

< Previous Page | 294 295 296 297 298 299 300 301 302 303 304 305  | Next Page >