Search Results

Search found 19676 results on 788 pages for 'hardware interface'.

Page 298/788 | < Previous Page | 294 295 296 297 298 299 300 301 302 303 304 305  | Next Page >

• Network config for KVM on physical machine with single NIC and single public IP

  - by neo0

  I have a physical machine running CentOS 6.4 and I will rent a place to run it in a data center. I want to install KVM on that machine to run some virtual machines. The problem is my physical machine have only one NIC and the data center give me a public IP for that interface. So how should I configure network on the physical machine to make it assign for each vm a private IP that can connect to Internet. If I create a br0 bridged with eth0 interface and create a vm with option --bridge=br0 then KVM could not assign an IP for the vm so setup can not be done. Should I use NAT mode? Does KVM have any host-only network like Virtualbox? But the vm still has to connect to outside? Thank you! Update I install the guest network using NAT (--network network:default) and then I only have to port-forwarding from the host. But if I config br0 bridged with physical eth0 then the guest can not get an IP from boot. So I removed the br0 and it worked.

  Read the article

• What LTO 4 drive to buy

  - by pplrppl

  Evan Anderson mentioned in another solution you could buy a LTO-4 (autoloader, 1 tape / day) - $4,566.00 (the discussion included total cost of tapes for a specific rotation.) but I don't know specifics on what he or you would recommend for the actual drive and if necessary controller. Show me a newegg URL or CDW, Dell, or HP, or whatever your favorite vendor would be for your solution if you don't mind looking it up or just give me a brand and a model number and I'll be glad to do the leg work myself. I currently have on have on hand an external LTO 3 drive that uses LVD SCSI interface (and thus have a controller card that has an external LVD SCSI connector). If that card isn't sufficient to interface to a LTO 4 drive let me know. http://www.fujifilmusa.com/shared/bin/LTO_Overview.pdf shows minimum tape speeds for LTO4 and other LTO formats. It looks like the IBM LTO4 actually has a lower minimum speed than the IBM LTO3. Either way my average server is too slow to feed LTO3/4 without shoeshining so I'm looking for a drive with a low minimum write speed. If you trust the PDF from 2008 that makes my choices IBM LTO 4 full height IBM LTO 4 half height HP LTO 4 half height but presumably there are other options out there that weren't mentioned in the fuji PDF. Again I'm looking for a specific recommendation on a drive to buy (and the controller if needed).

  Read the article

• Windows XP - Power surge on hub port

  - by Swift-Tuttle

  Since last few weeks I constantly get this error, as status bar balloon: Power Surge on Hub Port - A USB device has exceeded the power limits of its hub port. Due to this now I am unable to access any USB devices properly, they get disconnected intermittently. I did quite a few things to resolve this problem, firstly obviously through the Windows help. I even tried all the things told on the Microsoft website(which essentially says is to check and update the driver) but in vain. One suggestion, I found when I google'd was to disable the USB2 controller through the Device Manager and since at every startup the System configuration comes up complaining that it has been changed etc.(On that same site it is mentioned to ignore this message.) But after everything I still cant solve this problem. Any help is much appreciated. The system is installed with Windows XP service Pack 3 and all the updates till last month. Please let me know if any other hardware info is required. **UPDATE** My laptop is about 5 years old now, its an HP with Celeron 1.4G processor. Windows XP SP3 installed. All latest windows updates installed. 2 USB ports available. BIOS is HP 68DTD ver F.0A Do I need to update my BIOS from somewhere ? or is this a hardware problem altogether?

  Read the article

• USB mouse disconnecting and reconnecting in windows and linux

  - by Kalak

  I have a problem similar to what is described at "Why is my USB mouse disconnecting and reconnecting randomly and often?" except is is happening in both Windows 7 and Linux (Ubuntu 12/04TLS, fully patched), multiple mice, multiple OSs. It stops responding to input for about 3-5 seconds, then starts responding again. It's more frequent and lasts longer when running games (TF2, L4D, Dishonored, Borderlands 2, and more), but happens when just running the OS as well. I was hoping it was the motherboard so I bought a USB 2.0 PCI card to try that, but it's still happening. I've stripped it down to just the keyboard and mouse (different keyboard too just in case the keyboard was the problem), but it's still happening. All the hardware (mice and keyboards) work fine on other computers. I have literally pulled the mouse and keyboard out and plugged them into another computer (laptop) and re-joined the online game and had no problem with the keyboard and mouse combo that just failed on my gaming rig. Please no driver / Windows or Linux only suggestions, as that wouldn't effect both OSs. edit: known good mice I've brought home are now going bad. I suspect the hardware is messed up (voltage?) and has been frying the mice.

  Read the article

• Debian Linux bridging router intermittently dropping packets [migrated]

  - by nomen

  My old Asus router died a few weeks ago, so I thought I'd set up my Debian box to deal with routing my home network. I have a few complications, but I adapted my configuration from a previously working configuration, and I don't see why I am having intermittent problems. But I am having them! Every so often, my SSH connections to the router (and to the Xen virtual machines hosted by the router) just drop. I am unable to use the router's dns server. I can't ping the router. Etc. (I can provide more details, but I'm not sure what will be helpful) /etc/network/interfaces: # The loopback network interface auto lo iface lo inet loopback # Gigabit ethernet, internal network auto eth0 allow-hotplug eth0 iface eth0 inet manual # USB ethernet, internet auto eth1 allow-hotplug eth1 iface eth1 inet dhcp # Xen Bridge auto xlan0 iface xlan0 inet static bridge_ports eth0 address 10.47.94.1 netmask 255.255.255.0 As I understand it, this is sufficient to create the network interfaces, and even do some switching between Xen hosts and my eth0 interface. I installed and configured Shorewall to manage routing: /etc/shorewall/zones fw firewall net ipv4 lan ipv4 /etc/shorewall/interfaces net eth1 detect dhcp,tcpflags,nosmurfs,routefilter,logmartians lan xlan0 detect dhcp,tcpflags,nosmurfs,routefilter,logmartians,routeback,bridge /etc/shorewall/policy net all DROP info fw net ACCEPT info all all REJECT info /etc/shorewall/rules DNS(ACCEPT) fw net DNS(ACCEPT) lan fw ... and so on, these all work, when the router is accepting traffic at all. /etc/shorewall/masq eth1 10.47.94.0/24 Can anybody help?

  Read the article

• Limit bandwith on network of computers

  - by Joseph34123

  We have network in office of approximately 10 computers sometimes when someone downloads something for work (e.g. syncing email with an attachment or Dropbox), everyone slows down. I could limit each computer in office but the problem is that we have an open WiFi network, and I cannot access the computers that use it. We have one main DSL router "Netopia 3347" and another router connected to it on wire for public wifi is "Linksys WRT110". I cannot change the setup we have and don't want to. There's 2 approaches here: Set office computers download limit in each computer and then I need to find out how I can set a download limit for the wifi network such as in the router settings. It's a Linksys router and I did not see the option for this, so maybe I need new router for WiFi? Don't bother with each computer and put some "specific hardware" or another computer before router so all traffic goes trough it and I can then assign priority maximum speed for each IP address. Question is what hardware do I need?

  Read the article

• How can I debug user mode driver failures in Windows 8

  - by Tom

  I have a 32 GB SD Card. Whenever I insert this card in to my newly upgraded Windows 8 laptop the OS stops responding normally. Metro Apps won't work. The system may or may not log in. Desktop apps may or may not be able to do things. When I remove the card and restart then all is fine. As soon as I put the card back in, the system starts misbehaving again. I've run Windows Update, so I have the latest drivers from Microsoft. This does not occur with the 8 GB cards I have. Unfortunately I only have one 32 GB card, so I can't test with others. From examining the system event log I've determined this is happening due to a user mode driver failure. How can I best debug this issue from here? How can I figure out which driver this is related to? Will there be a Dr. Watson crash dump somewhere? Details - System - Provider [ Name] Microsoft-Windows-DriverFrameworks-UserMode [ Guid] {2E35AAEB-857F-4BEB-A418-2E6C0E54D988} EventID 10110 Version 1 Level 1 Task 64 Opcode 0 Keywords 0x2000000000000000 - TimeCreated [ SystemTime] 2012-10-29T00:51:57.532718300Z EventRecordID 40417 Correlation - Execution [ ProcessID] 1056 [ ThreadID] 3796 Channel System Computer thebrain - Security [ UserID] S-1-5-18 - UserData - UMDFHostProblem [ lifetime] {811E3DC4-FBC6-420B-ABCC-AD7505A36F3B} - Problem [ code] 3 [ detectedBy] 2 ExitCode 3 - Operation [ code] 259 Message 72448 Status 4294967295 Edit 1 So I tried using Debug View from SysInternals (you can get it here: http://technet.microsoft.com/en-us/sysinternals/bb896647.aspx). That gave me this information: which is not especially helpful. Then I tried connecting WinDbg to WUDFHost.exe (the process that seems to host user mode drivers) to see if it could catch the error. Get it here: http://msdn.microsoft.com/en-US/windows/hardware/hh852363 Instructions: http://msdn.microsoft.com/en-US/library/windows/hardware/ff554716(v=vs.85).aspx That didn't help much. It didn't catch any exceptions as I'd hoped (which would point me to the cause of the crash at least). Here's the stack of one of the threads:

  Read the article

• How do you handle data archiving?

  - by 20th Century Boy

  Backups are one thing, but long term archival is another. For example, you might be required to store emails for 7 years, or keep all project data indefinitely. I used to save archives to tape, but then I've had tapes get destroyed (drives rip the tape out). So...write to 2 tapes I hear you say. Is that what others do? Have 2 (or more) tapes of the same data for redundancy? But then the other issue is that tapes cannot usually be read by different backup software vendors. Eg if you go from Arcserve - Backup Exec - Commvault over 10 years you would need to keep all 3 systems so that you could restore old data. Likewise for hardware. Old tapes might not be barcoded. Might not be compatible with the new library etc etc. So do you keep old tape hardware AND old software just in case you might need to restore a 10 year-old file? Or...when you move to a new backup system do you migrate all archived data to the new system and re-archive it onto new tapes? That could be a huge job. Any thoughts?

  Read the article

• Public-to-Public IPSec tunnel: NAT confusion

  - by WuckaChucka

  I know this is possible -- and apparently fairly common with larger companies that don't/can't route private addresses for overlap reasons -- but I can't wrap my head around how to get this to work. I'm playing around with pfSense, Vyatta and a Cisco 5505 right now, hardware-wise. So here's my setup: WEST: Vyatta outside: 10.0.0.254/24 inside: 172.16.0.1/24 machine a: 172.16.0.200/24 EAST: Cisco 5505 outside: 10.0.0.210/24 inside: 192.168.10.1 machine b (webserver): 192.168.10.2 So what we're trying to do is this: route traffic across the tunnel from machine A to machine B without using private addresses. i.e. 172.16.0.200 makes a TCP request to 10.0.0.210:80, and as far as EAST is concerned, it sees a src IP of 10.0.0.254. On WEST, I have your typical many-to-one Source NAT to translate 172.16.0.0/24 to 10.0.0.254 and that's confirmed to be working. Also on WEST, I have the following IPSec config: Local IP: 10.0.0.254 Peer IP: 10.0.0.210 local subnet: 10.0.0.254/32 remote subnet: 10.0.0.210/32 I have the reversed configuration on EAST. What happens when I make a request from machine A to 10.0.0.210:80 is that the SNAT translates the private address of machine A to 10.0.0.254 and it's routed out (and discarded at the other end) without establishing the tunnel. What I'm assuming is happening is that the inside interface on WEST receives a packet from 172.16.0.200 and since this doesn't match the local subnet defined in the tunnel configuration, it's not processed by the IPSec engine and the tunnel is not established. How do you make this work? Seems like a chicken and egg thing with the NAT and IPSec and I just can't wrap my head around how this can be done: can I say, "if a packet is received on the inside interface with a destination of 10.0.0.210, translate it to 10.0.0.254 before the IPSec engine inspects it"?

  Read the article

• Kernel hacking methodology - how to find out where to hack the linux kernel

  - by Flavius

  I have a throw-away cheap laptop I'd like to twiddle around, a Thinkpad SL 500. What bothers me are two leds, the one for wireless connectivity, and the one for hibernation, which don't light up at all, although they're functional, I've tried it on windows. So I would like to write a kernel driver for them, nothing big, it just looks like a good idea to play around with the kernel. My question is what methodology should I follow systematically to find out what devices are responsible for those leds (in general, not necessarily specific to my hardware), and what drivers are responsible for the other two leds that work, bluetooth and the battery indicator? And when I say methodology, I really mean the methodology, step by step, with reasons for each step, like in the answer I've gave to someone else over here: What does && mean in void *p = &&abc; I am profficient at fgrepping through big code repositories, using static code analysers & co, but I think my lack of hardware knowledge hinders me on this problem. PS: I'm using ArchLinux, so almost the latest kernel version.

  Read the article

• Server 2008 NAT Internet Not Working

  - by Jack

  I'm trying to set up Routing and Remote Access on Windows Server 2008 R2, I have a network connection that I want to share the internet from to another private network. The server has two NICs which are configured as follows: External NIC (Dynamically assigned by ISP) IP:10.175.4.150 Subnet:255.255.192.0 Gateway:10.175.0.1 DNS:10.175.0.1 Internal NIC IP:172.16.254.1 Subnet:255.255.255.0 Gateway:None DNS:None I have set the external NIC to be the public interface and enabled NAT on it in the RRAS MMC and set the internal NIC to be a private interface. I have also set up the DNS forwarding or whatever it is in the NAT section. From a client (IP:172.16.254.2) I can ping the server and access files on it, when I try to browse the web with the default gateway set to the internal NIC ip I end up getting a 404 page which is returned from the ISPs default gateway. I'm guessing it's something to do with the double NAT possibly. Trying to ping the ISPs default gateway from a private network client just times out as does accessing it directly. I've disabled and reconfigured RRAS multiple times and that doesn't seem to have made a difference, so can anyone tell me what I'm doing wrong? Thanks.

  Read the article

• Upgrading openSUSE 11.1 with Plesk Panel 9.3 to PHP 5.3

  - by Jonathan Hogervorst

  Hello, I'm running a VPS with openSUSE 11.1 (i586). On the VPS is Parallels Plesk Panel 9.3.0 installed. The current PHP-version is PHP 5.2.11. I want to upgrade PHP to PHP 5.3, but I can't find good instructions on how to do this. If I check for updates in Zypper, it says this is the latest release. In the Plesk Updates isn't an update either, both via the webbased interface and the command line interface. On Software.openSUSE.org I can find packages for PHP 5.3.1 in both the server:php/server_apache_openSUSE_11.1-repo and the server:php/openSUSE_11.1-repo (can't post the link because I'm a newbie here). But if I add one of those to Zypper, I still don't see an update. Is there here somebody who knows how to do this? And is it completely safe to update that way? I don't want to end up with a broken VPS... Thanks! Jonathan

  Read the article

• SQL Server 2008 R2 mirroring failing

  - by andriusn

  I have two Windows 2008 R2 (Amazon EC2) instances running SQL Server 2008 R2. I use 9TB striped disks (9x1TB EBS volumes) for storage. One server is running as principal and second one as mirror. Both started from the same image, database and tlog files located on striped disk. Mirror server failed 3 times in last 2 months with errors: EventID 823 The operating system returned error 2(The system cannot find the file specified.) to SQL Server during a write at offset 0x00000048058a00 in file 'D:\TLogs***_log.ldf'. Additional messages in the SQL Server error log and system event log may provide more detail. This is a severe system-level error condition that threatens database integrity and must be corrected immediately. Complete a full database consistency check (DBCC CHECKDB). This error can be caused by many factors; for more information, see SQL Server Books Online. and EventID 1454 Database mirroring will be suspended. Server instance 'xxxxxxxxxx' encountered error 823, state 6, severity 24 when it was acting as a mirroring partner for database '***'. The database mirroring partners might try to recover automatically from the error and resume the mirroring session. For more information, view the error log for additional error messages. followed by EventID 19019 The MSSQLSERVER service terminated unexpectedly. After this rebooting instance is necessary to restore mirroring. First two times I thought it was hardware related (striped disk failure) and relaunched instance on new hardware. But the issue is back after few weeks again. It only affects mirror instances. Any help would be really appreciated. Thanks.

  Read the article

• Media Center - TV constantly pauses 1/2 second then plays 1 second

  - by Bob

  I have a problem watching TV in Media Center. The TV constantly pauses 1/2 second then plays 1 second, pauses 1/2 second, plays 1 second - it is constant and does not vary. I know the problem is Media Center because I can use Pinnacle's TVCenterPro and there is no skipping/pausing. I was using cable, and switched to DirecTV (satellite). Trying to do "Set up TV signal" in Media Center seems to be what broke it. I get an error "IR Hardware not detected." I can use the remote to "try again" - so the IR hardware works fine (Media Center's remote/sensor). I tried plugging the IR Blaster into both ports, and I tried a different USB port for the IR receiver. I can't complete the setup. Media Center was playing it okay before I tried to run setup. (I ran setup to try to do recording with Media Center.) Pinnacle PCTV 800i HD PCI card, ATI Radeon HD 3200 Graphics, Windows XP SP3 Media Center Edition, AMD Athlon Dual Core 2.5 GHz, 1.75 GB RAM.

  Read the article

• Easy GUI way to auto scale EC2 and RDS: aws console, scalr, ylastic...?

  - by Zillo

  I am managing all my instances with the AWS Management Console (the GUI web console) but now I want to use Auto Scale and it seems that this can not be done with that console. Yes, there is CloudWatch but I can only create alarms (e-mail notifications), it seems that CouldWatch needs you to add the auto scale policy in some other place (by command line console?). I would like to use some easy GUI interface. Ylastic and Scalr seems to be a good option. Which one do you think is better? Regarding Scalr, is there any difference between the open source software Scalr and the service Scalr.net? I mean, is the GUI interface the same? I like the idea of the Scalr because I do not need to give my Secret Access Key to a third party (like in Ylastic or in Scalr.net) One question about the Scalr software, it has to be installed in the instances or it must be installed in another machine? Do I need to setup again all my security permissions, AMIs, snapshots, etc. or I can use AWS Management Console for everything and Scalr just to auto scale.

  Read the article

• How to setup an IPSec / GRE tunnel on Windows Server 2008

  - by qbeuek

  I have a Windows Server 2008 that has a single network interface configured with a public IP address. My business partner has a private network. From my server, I need to access all the devices on his private network, and those devices must be able to access my server. My business partner has a standard solution for these requirements. They will setup an IPSec + GRE tunnel to my server. They told me, that I will need an additional public IP address for this to work. If it really is necessary, there is no problem, I can get an additional public IP address, although it will be assigned to the same physical network interface. I assume that on my server I will have both public IP addresses and also the private IP address from the tunnel (the same that is visible for the devices inside the private network). What alternatives do I have? Is it possible to configure this tunnel on my Windows Server 2008? Can it be done using only Windows tools, or do I need an additional free / commercial VPN software? If it cannot be done directly on Windows, can I setup an additional virtual machine running Linux, that will handle the IPSec + GRE tasks? How to do it? If it cannot be done on a virtual linux box, will I have to buy and setup a Cisco router to handle the IPSec + GRE tasks? Thanks for your opinions. I'm watching this question to clarify any issues or questions.

  Read the article

• Internet slowed down because of SQUID Server setup

  - by Ranjith Kumar

  Recently I have setup a squid server for our office. I have computer (A) with two ethernet cards, one for internet and the second one for local networkIt has Ubuntu server OS with squid-server and dhcp3-server installedI have added few iptable rules to work like a router and redirect all http traffic to 3128 port This link is my reference. Everything worked fine for 2 days. All of a sudden internet speed went down drastically. When I connected the internet cable to my laptop to test the internet speed it was fine. Again when I reconnected it back to computer A everything was normal. This happened 4 times in a week. Could anyone here please help me why the internet speed is going down and it becomes normal when I reconnect the cable. EDIT: Rebooting the system (computer A) didn't make a difference. I have changed iptables so that http traffic doesn't redirect to 3128 port any further, still no change in the internet speed. I think the problem is not with squid but with something else. Here are my iptable rules SQUID_SERVER="10.1.1.1" INTERNET="eth1" LAN_IN="eth0" SQUID_PORT="3128" PROXYSERVERS=(Atlanta Baltimore Boston Chicago Dallas Denver Houston KansasCity LosAngeles Miami NewYork Philadelphia Phoenix SanAntonio SanDiego SanJose Seattle Washington) SERVERLEN=${#PROXYSERVERS[*]} I=0 iptables -F iptables -X iptables -t nat -F iptables -t nat -X iptables -t mangle -F iptables -t mangle -X modprobe ip_conntrack modprobe ip_conntrack_ftp echo 1 /proc/sys/net/ipv4/ip_forward iptables -P INPUT DROP iptables -P OUTPUT ACCEPT iptables -A INPUT -i lo -j ACCEPT iptables -A OUTPUT -o lo -j ACCEPT iptables -A INPUT -i $INTERNET -m state --state ESTABLISHED,RELATED -j ACCEPT iptables --table nat --append POSTROUTING --out-interface $INTERNET -j MASQUERADE iptables --append FORWARD --in-interface $LAN_IN -j ACCEPT iptables -A INPUT -i $LAN_IN -j ACCEPT iptables -A OUTPUT -o $LAN_IN -j ACCEPT while [ $I -lt $SERVERLEN ]; do iptables -t nat -A PREROUTING -i $LAN_IN -p tcp -d ${PROXYSERVERS[$I]}.wonderproxy.com --dport 80 -j ACCEPT let I++ done iptables -t nat -A PREROUTING -i $LAN_IN -p tcp --dport 80 -j DNAT --to $SQUID_SERVER:$SQUID_PORT iptables -A INPUT --protocol tcp --dport 80 -j ACCEPT iptables -A INPUT --protocol tcp --dport 443 -j ACCEPT iptables -A INPUT --protocol tcp --dport 22 -j ACCEPT iptables -A INPUT -j LOG iptables -A INPUT -j DROP

  Read the article

• Does AMD Cool n Quiet Slow Down Your System?

  - by Software Monkey

  I discovered today that having AMD Cool n Quiet enabled in my BIOS appears to be slowing down my Windows XP SP2 system by about 29% on memory & CPU intensive workloads. I was wondering if (a) anyone else had encountered this, (b) anyone can offer an explanation, (c) there are any negatives I need to be aware of if I keep AMD CnQ disabled. With some superficial testing so far, I don't immediately notice any difference with CnQ off (other than the performance being what I expected from this new hardware). It seems to ramp up the CPU fan a little bit as my program maxes out 1 core, but that's the same as with CnQ on. And when I let the system idle the CPU fan slows down and the systems as quiet as a mouse (after years of 6 small fans churning like they want to go into orbit it's nice to again have a system where I can hear the HDDs seeking). Bonus question: Does CnQ cause issues with system stability? I ask because the reason I disabled it was because I have had a few freezes and 1 spontaneous reboot with my new hardware.

  Read the article

• Creating basic, redundant gigE or IB storage network for Xen?

  - by StaringSkyward

  With only a modest budget, I want to move my 4 xen servers over to network storage -either NFS or iSCSI which will be determined based on how well it performs when we test it (we need good throughput and it must continue to work through link and switch failure tests). We may add another couple of xen servers at some point when this is done. I don't know much about the design and operation of storage networks, so would really appreciate some hints from those with experience. The budget is around $3,800 excluding the storage appliance. I am currently thinking these are my options to remain on budget: 1) Go for used infiniband hardware and aim for 10gb performance. 2) Stick with gig ethernet and buy some new switches (cisco or procurve) to create a storage-only ethernet LAN. Upgrade to 10gigE later but try to use hardware capable of it where possible to reduce upgrade costs. I have seen used, warrantied infiniband switches at reasonable prices (presumably because big companies are converging on 10gbit ethernet?) and the promise of cheap 10gb is attractive. I know nothing about IB, so here come the questions: Can I buy 2 x switches and have multiple HBAs in my xen and storage nodes to get redundancy and increased performance without complexity or expensive management software costs? If so, can you point me to some examples? Do NFS and iSCSI work just the same regardless? Is IB a sensible choice or could/should I use ethernet or FC on the same budget - I'm keen not to get boxed into a corner for future upgrades, however. For the storage I am likely to build a storage server using nexentastor with the intention that I can later add more disks, SSDs and add another server to provide a failover option at the storage level. An HP LeftHand starter SAN is also under consideration, too. Thanks in advance.

  Read the article

• Abnormally high amount of Transmit discards reported by Solarwinds for multiple switches

  - by Jared

  I have several 3750X Cisco switches that, according to our Solarwinds NPM, are producing billions of transmit discards per day. I'm not sure why it's reporting these discards. Many of the ports on the 3750X's have 2960's connected to them and are hardcoded as trunk ports. Solarwinds NPM version 10.3 Cisco IOS version 12.2(58)SE2 Total output drops: 29139431: GigabitEthernet1/0/43 is up, line protocol is up (connected) Hardware is Gigabit Ethernet, address is XXXX (bia XXXX) Description: XXXX MTU 1500 bytes, BW 100000 Kbit/sec, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 100Mb/s, media type is 10/100/1000BaseTX input flow-control is off, output flow-control is unsupported ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:47, output 00:00:50, output hang never Last clearing of "show interface" counters 1w4d Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 29139431 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 35000 bits/sec, 56 packets/sec 51376 packets input, 9967594 bytes, 0 no buffer Received 51376 broadcasts (51376 multicasts) 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog, 51376 multicast, 0 pause input 0 input packets with dribble condition detected 115672302 packets output, 8673778028 bytes, 0 underruns 0 output errors, 0 collisions, 0 interface resets 0 unknown protocol drops 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier, 0 pause output 0 output buffer failures, 0 output buffers swapped out sh controllers gigabitEthernet 1/0/43 utilization: Receive Bandwidth Percentage Utilization : 0 Transmit Bandwidth Percentage Utilization : 0

  Read the article

• Media Center setup won't complete for watching TV

  - by Robert

  I have a problem watching TV in Media Center. The TV constantly pauses 1/2 second then plays 1 second, pauses 1/2 second, plays 1 second - it is constant and does not vary. This problem occurs on all channels, live or recorded. The bottom 5th of the screen is solid green. I know the problem is Media Center because I can use Pinnacle's TVCenterPro and there is no skipping/pausing (and not green on bottom). I was using cable, and switched to DirecTV (satellite). Trying to do "Set up TV signal" in Media Center seems to be what broke it. I get an error "IR Hardware not detected." I can use the remote to "try again" - so the IR hardware works fine (Media Center's remote/sensor). I tried plugging the IR Blaster into both ports, and I tried a different USB port for the IR receiver. I can't complete the setup. Media Center was playing it okay before I tried to run setup. (I ran setup to try to do recording with Media Center.) Pinnacle PCTV 800i HD PCI card (coax cable from DirecTV tuner), ATI Radeon HD 3200 Graphics, Windows XP SP3 Media Center Edition, AMD Athlon Dual Core 2.5 GHz, 1.75 GB RAM.

  Read the article

• Public static ip for vagrant box

  - by Numbata

  I have server (Debian Squeeze) with 1 ethernet card and 2 public static IPs (188.120.245.4 and 188.120.244.5). What I want: Setup virtual box (Ubuntu) with access via static IP (188.120.244.5). What I was trying: config.vm.forward_port - good idea: setup interface "eth1:1" with 188.120.244.5 on host-machine, and add to Vagrant file "config.vm.forward_port = hmm..?" config.vm.network :hostonly, "188.120.244.5" - not working. Was created new interface on host-machine with ip "188.120.244.1". Of course 188.120.244.1 IP isn't mine and I can't access my server via this IP. config.vm.network :bridged - I'm confused how this works :) What I have now: Not working configuration. Debian-host-machine# cat Vagrantfile Vagrant::Config.run do |config| config.vm.define :gitlab do |box_config| box_config.vm.box = "ubuntu" box_config.vm.host_name = "ubuntu" box_config.vm.network :bridged box_config.vm.network :hostonly, "188.120.244.5", :auto_config => false end end Debian-host-machine# ifconfig eth1 Link encap:Ethernet HWaddr 00:15:17:69:71:bb inet addr:188.120.245.4 Bcast:188.120.247.255 Mask:255.255.248.0 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 vboxnet0 Link encap:Ethernet HWaddr 0a:00:27:00:00:00 inet addr:188.120.244.1 Bcast:188.120.246.255 Mask:255.255.255.0 Ubuntu-virtual-machine# ifconfig eth0 Link encap:Ethernet HWaddr 08:00:27:ee:8d:0c inet addr:10.0.2.15 Bcast:10.0.2.255 Mask:255.255.255.0 eth1 Link encap:Ethernet HWaddr 08:00:27:45:71:87 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 How I can access virtual box via public static IP from network? I'm using Oracle VM VirtualBox Manager 4.1.18 and Vagrant version 1.0.3. Thanks in advance for your feedback.

  Read the article

• Cisco Catalyst 4500 Policy Based Routing

  - by Logan

  In order to test a new firewall I just set up I'm trying to implement policy based routing on our core switch. I want traffic from certain vlans to be routed to the new firewall while everything else continues being routed through the old firewall. I was trying to use this guide. Everything from that guide works fine except trying to run the "ip policy route-map" command in the interface configuration mode. IOS is telling me that such a command doesn't exist. A "show ip interface vlan" command says that policy routing is disabled. Any ideas? Output of "show ver": Cisco IOS Software, Catalyst 4500 L3 Switch Software (cat4500-IPBASEK9-M), Version 12.2(53)SG, RELEASE SOFTWARE (fc3) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2009 by Cisco Systems, Inc. Compiled Thu 16-Jul-09 19:49 by prod_rel_team Image text-base: 0x10000000, data-base: 0x11D1E3CC ROM: 12.2(31r)SG2 Dagobah Revision 226, Swamp Revision 34 RTTMCB2223-1 uptime is 3 years, 22 weeks, 2 days, 19 hours, 28 minutes Uptime for this control processor is 51 weeks, 2 days, 18 hours, 2 minutes System returned to ROM by power-on System restarted at 19:22:02 UTC Tue Jul 12 2011 System image file is "bootflash:cat4500-ipbasek9-mz.122-53.sg.bin" ... cisco WS-C4510R (MPC8245) processor (revision 4) with 524288K bytes of memory. Processor board ID FOX103703W3 MPC8245 CPU at 400Mhz, Supervisor V Last reset from PowerUp 42 Virtual Ethernet interfaces 244 Gigabit Ethernet interfaces 511K bytes of non-volatile configuration memory. Configuration register is 0x2

  Read the article

• VMware and Windows Activation

  - by Peter M

  Yesterday I installed Slysoft's Virtual CloneDrive in order to mount an iso for some software installation on my host system (XP Pro SP3) This morning I fired up VMware and made a linked clone of an existing XP vm in order to do some software testing. This is the sort of thing that I do all the time, and the base XP vm that I clone was activated a long long time ago. The surprise today was that the newly cloned vm was no longer activated and XP cited major changes in hardware as the reason. I repeated the test with a full clone of the base system and got the same message. I then started up my base vm and it seemed to be activated, yet another vm (which I fully cloned from the base vm a long time ago) now started reporting that XP was not activated. At this point I guessed that Virtual DriveClone might have been the source of my hardware differences so I uninstalled it and rebooted. After this I made a new linked clone and full clone of the base vm and XP did not complain about not being activated. So I seem to be back to where I was before installing Virtual DriveClone with the exception that that one particular XP vm continues to complain about activation (even though 4 or 5 other XP vm's are fat and happy) Now to my questions: Why would adding Virtual CloneDrive to the host system affect XP activation on the vm's? From their point of view I would have thought that the environment had not changed as I had not enabled any new hard drives in their systems. Or is adding a hard drive to the host system enough to upset XP activation? Since this event, one of my fully cloned vm's is still reporting that XP is not activated even though I have removed Virtual CloneDrive. Is there anyway to convince XP that it is on the same system as yesterday? Or are my only options to do an activation or restore the vm from a previous backup?

  Read the article

• Value of Itanium over x86_64 for Oracle Deployment

  - by Antitribu

  We are looking at a new environment to run our Oracle Database running on SUSE (potentially migrating to RedHat). Our database is approximately 100GB and performs adequately on our current hardware (x86_64) with approximately 6GB of ram allocated to it. We are growing quickly however and will require more performance shortly. Given the cost of Oracle licenses we would like to maximize the value from each license by choosing the most appropriate CPU to run the software on. The questions are: Are there substantial benefits to looking at Itanium hardware, are there any drawbacks? Is there a point where Itanium starts to scale out better? What are the long term support options for Itanium? Given the dominance of x86 would it be safer long term to stick with x86? On average what would be the performance benefit of implementing an Oracle database on Itanium over x86_64? Is this an issue at all or will other factors (IO/RAM) cap out first? If anyone can point me towards some solid documentation on comparisons between the two platforms that provides good case analysis of when to choose which I'm more than happy to accept that as an answer.

  Read the article

< Previous Page | 294 295 296 297 298 299 300 301 302 303 304 305  | Next Page >