Search Results

Search found 9889 results on 396 pages for 'pointer speed'.

Page 298/396 | < Previous Page | 294 295 296 297 298 299 300 301 302 303 304 305  | Next Page >

• Wireless router blocking some sites while using ethernet is fine

  - by Micke

  I'm using Windows 7 and my router is a wireless Apple Airport Express that is approximately two years old. Suddenly I can't access some sites (for example www.sthlm.friskissvettis.se, or www.vegetarian-shoes.co.uk, some streamed tv-shows on svtplay.se, and a number of other random sites) when connecting to internet with my router. It worked good until recently and I'm fairly sure this problem emerged when my ISP upgraded from 10/10mbit to 100/10mbit speed. Most other sites like facebook and google works fine. When using my network cable to connect to internet everything works fine and I can access these sites. Firmware is current and I've tried reseting the router to factory defaults. Tried different browsers, and I can't ping the "blocked" sites either. Tracert www.sthlm.friskissvettis.se starts with 10.0.0.1 and continues through a number of long addresses until it says timeout. The last working address before timeout was sth-tcy-ipcore01-ge-0-2-0.neq.dgcsystems.net [83.241.252.13], if it matters. Tracert www.vegetarian-shoes.co.uk also eventually gives me a timeout. When the network cable is plugged in, I still get timeout on tracert www.sthlm.friskissvettis.se even though I can access the site in Chrome. Weird. www.vegetarian-shoes.co.uk doesn't give me a tracert timeout when the cable is plugged in, and I can access the site as usual. I've tried changing DNS servers to use opendns servers instead, but to no use. I've tried pinging these two sites with a lower MTU packet size (with this method: http://www.richard-slater.co.uk/archives/2009/10/23/change-your-mtu-under-vista-or-windows-7/), but still can't access them through ping... I don't know what to do anymore.... any suggestions???

  Read the article

• HP Procurve 2610 intervlan routing

  - by user19039

  Can anyone tell me why inter vlan routing is working for all vlans except my newly created vlan 4/ I have an hp procurve 2610. Any help would be appreciated. I have basically this 1 switch with all unmanaged switches attached to the core. We have a second 2610 on port 28 Running configuration: ; J9085A Configuration Editor; Created on release #R.11.25 hostname "Core_HP" interface 22 speed-duplex 100-full exit ip routing snmp-server community "public" Unrestricted vlan 1 name "DEFAULT_VLAN" untagged 1-12,17-22,26-27 ip address 192.168.4.6 255.255.255.0 tagged 25 no untagged 13-16,23-24,28 exit vlan 2 name "WAN" untagged 28 ip address 10.254.254.3 255.255.255.0 exit vlan 3 name "Wireless" untagged 13-16,24 ip address 192.168.7.6 255.255.255.0 ip helper-address 192.168.4.2 tagged 27 exit vlan 35 name "guest" untagged 23 tagged 24 exit vlan 4 name "esxi" untagged 25 ip address 10.10.1.1 255.255.248.0 exit ip route 192.168.5.0 255.255.255.0 10.254.254.1 ip route 192.168.6.0 255.255.255.0 10.254.254.1 ip route 0.0.0.0 0.0.0.0 192.168.4.10 show ip route IP Route Entries Destination Gateway VLAN Type Sub-Type M etric Dist. ------------------ --------------- ---- --------- ---------- - --------- ----- 0.0.0.0/0 192.168.4.10 1 static 1 1 10.10.0.0/21 esxi 4 connected 0 0 10.254.254.0/24 WAN 2 connected 0 0 127.0.0.0/8 reject static 0 250 127.0.0.1/32 lo0 connected 0 0 192.168.4.0/24 DEFAULT_VLAN 1 connected 0 0 192.168.5.0/24 10.254.254.1 2 static 1 1 192.168.6.0/24 10.254.254.1 2 static 1 1 192.168.7.0/24 Wireless 3 connected 0 0 show ip Internet (IP) Service IP Routing : Enabled Default TTL : 64 Arp Age : 20 VLAN | IP Config IP Address Subnet Mask Prox y ARP ------------ + ---------- --------------- --------------- ---- ----- DEFAULT_VLAN | Manual 192.168.4.6 255.255.255.0 No WAN | Manual 10.254.254.3 255.255.255.0 No Wireless | Manual 192.168.7.6 255.255.255.0 No esxi | Manual 10.10.1.1 255.255.248.0 No guest | Disabled

  Read the article

• SSD, AHCI and write performance

  - by Dan

  We've started to deploy SSD drives to our developers workstations. At this moment we're having the unpleasant surprise that the systems using the new SSDs often freeze, with the HDD activity led blinking or being continuously on. Benchmarks shows read speeds around 180 MB/s, but write speeds around 5 MB/s. All developers are using Windows 7 Enterprise, 64 bit, SP1. One of our developers suggested (based on his experience) the following sequence: backup the workstation use a tool to completely erase the SSD make sure AHCI is enabled in BIOS install Windows restore from backup So far, this procedure seems to work (we're still testing, but write speed seems to be 120 MB/s). There are some questions in this context: why do we have to completely reinstall Windows? Is it possible to clean the SSD without reinstalling Windows? Is there a reliable tool? If AHCI was disabled when Windows was installed and we enable it, shouldn't this be enough to correct the write performance issue? If we have to completely erase the SSDs, does this mean the SSDs we've received were used before (SH)? I'm wondering this because the package I've got was open (I didn't think about it at that time, as I considered one of my coworkers simply took a peek inside the package). Has anyone seen a similar problem before?

  Read the article

• Fetch videos from sony handycam to linux

  - by bstpierre

  I've got a Sony Handycam DCR-DVD101. When I plug connect the USB cable to my laptop (Ubuntu 10) it doesn't mount any storage device. If I run usb-devices, I see: T: Bus=02 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#= 6 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=054c ProdID=00c1 Rev=01.00 S: Manufacturer=SONY S: Product=Storage Device C: #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr=2mA I: If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=05 Prot=50 Driver=usb-storage The driver says usb-storage, but I'm not sure how to get the device mounted. Is there a way to make this work? Update: checking dmesg, I see: [259072.576559] usb 2-1.1: new high speed USB device using ehci_hcd and address 6 [259072.687200] usb 2-1.1: configuration #1 chosen from 1 choice [259072.836188] Initializing USB Mass Storage driver... [259072.836476] scsi5 : SCSI emulation for USB Mass Storage devices [259072.836632] usb-storage: device found at 6 [259072.836636] usb-storage: waiting for device to settle before scanning [259072.836660] usbcore: registered new interface driver usb-storage [259072.836666] USB Mass Storage support registered. [259077.830410] usb-storage: device scan complete [259077.832343] scsi 5:0:0:0: CD-ROM SONY DDX-A1010 R1.0 PQ: 0 ANSI: 0 [259077.888167] sr1: scsi3-mmc drive: 0x/0x pop-up [259077.888446] sr 5:0:0:0: Attached scsi CD-ROM sr1 [259077.888593] sr 5:0:0:0: Attached scsi generic sg2 type 5 [259080.002079] sr 5:0:0:0: [sr1] Unhandled sense code [259080.002085] sr 5:0:0:0: [sr1] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [259080.002091] sr 5:0:0:0: [sr1] Sense Key : Blank Check [current] [259080.002097] sr 5:0:0:0: [sr1] Add. Sense: No additional sense information [259080.002104] sr 5:0:0:0: [sr1] CDB: Read(10): 28 00 00 00 00 00 00 00 02 00 00 00 [259080.002117] end_request: I/O error, dev sr1, sector 0 [259080.002123] Buffer I/O error on device sr1, logical block 0 [259080.002128] Buffer I/O error on device sr1, logical block 1 Those I/O errors don't look good, is there any hope?

  Read the article

• needing storage integrity (write/read) test - for BASH

  - by Mr. Bash

  In need of shell scripts / bash commands to verify data integrity of local harddrives, usb-drives, etc, ... Like the famous www.heise.de/download/h2testw; or something that is at least common within repositories. (h2testw writes a specific datastring over and over onto the medium, then reads it again to verify if it was written correctly and displays write/read time/speed.) please no dd if=/dev/random of=/dev/sdx bs=1k && dd if=/dev/sdx of=/dev/null bs=1k since it won't verify if everything was written correctly. It is only a test if read/write is successful to the device. So far, I'm not too happy with badblocks -w -v /dev/sdx1 either, since it seems rather slow and I don't know what it exactly writes, and if it considers wear-leveling on flash media. There is also a program named F3 http://oss.digirati.com.br/f3/ that needs to be compiled. Designed after h2testw, the concept sounds interesting, i'd just rather have it as a ready to go bash script.

  Read the article

• Is "DSLAM congestion" a legitimate reason for slow DSL?

  - by Jay Bazuzi

  My DSL has been extremely slow in the evenings recently. To test it, I telnet to my DSL Modem, and ping the gateway. This way I eliminate internet congestion and local network issues. In the mornings I get 30ms - 50ms pings. In the evenings, it bounces around a lot, but 10000ms pings are common. I complained to Qwest support, and they said it was a known issue on their end, their engineers were working on it, and wouldn't say anything else. A couple days later I complained again, and they sent out a technician. He tested my house wiring and found that one of them had a short. It was an unused line, so we disconnected it, and he said things looked better and left. My daytime speeds improved at this point, but evening is still bad. I complained to Qwest support again, and they said it was a problem with DSLAM congestion at their end, and that they were working on it, but no ETA. My neighbor has Qwest DSL and doesn't seem to have these problems. That seems strange. I go use her network when I absolutely must get online and mine is behaving badly. I can't tell if they're yanking my chain or not. Regardless, these speeds are crap. I'm paying for 7Mpbs but am lucky if I get 1/10th that in the evenings. My kids like to watch Netflix streaming movies, and it's just impossible after 5pm or so. Should I wait it out? Will complaining again produce any results? Should I change my subscription to a lower speed until they fix their end? Or switch to cable?

  Read the article

• Limit bandwith on network of computers

  - by Joseph34123

  We have network in office of approximately 10 computers sometimes when someone downloads something for work (e.g. syncing email with an attachment or Dropbox), everyone slows down. I could limit each computer in office but the problem is that we have an open WiFi network, and I cannot access the computers that use it. We have one main DSL router "Netopia 3347" and another router connected to it on wire for public wifi is "Linksys WRT110". I cannot change the setup we have and don't want to. There's 2 approaches here: Set office computers download limit in each computer and then I need to find out how I can set a download limit for the wifi network such as in the router settings. It's a Linksys router and I did not see the option for this, so maybe I need new router for WiFi? Don't bother with each computer and put some "specific hardware" or another computer before router so all traffic goes trough it and I can then assign priority maximum speed for each IP address. Question is what hardware do I need?

  Read the article

• Is it possible to detect nearby Wi-Fi enabled devices, not necessarily on the same network? [closed]

  - by Sky

  first question on StackExchange ever. I hope I got the right board. I'm trying to create a device (either from a standard AP or some other unconventional means) that will be able to detect nearby Wi-Fi enabled devices. For example, if a cellular phone (iPhone for instance) would be carried into the secured area, its MAC address will be logged. A cellular phone is a good example because it's the most common threat that should be detected. Some important points: The detection can be either active or passive, doesn't matter. The detected device might be connected to a different network, or might not be connected to anything at all. I assume most cellular phones are actively probing when not connected, but I'm not sure. It is important to not only identify the breach, but also to identify the device (MAC address). Conventional hardware is only optional. Distance of detection is at least 6 meters (20 feet). Handling one device at a time is good. Speed of detection is important, under 5 seconds is ideal. So my question is, is this even possible? If so, what can I use in order to make this a reality? Thank you for reading!

  Read the article

• Tuning Windows 7 for use in a VM

  - by intuited

  I'm running Windows 7 in a VirtualBox Virtual Machine, and would like to make it run in a more streamlined fashion. I'll be using the install primarily for testing web apps, and have no need for it to run quickly. I would like it to run with minimal memory requirements, and with minimal changes to its virtual hard drive's contents. Changes to the hard drive contents, for example the paging file, result in larger snapshot sizes. Another recent post of mine seems to be related to this issue, but does not directly address issues with Windows. One concern that I have is that Windows seems to be using 17% of its paging file even with over 900MB of memory marked "Standby" or "Free". My uneducated guess is that this is being used to store indexes or some other data that helps to speed up the system but is not really necessary. I'm also wondering if it's normal for Windows to use over 500 MB of "In Use" memory with no apps running. Will this amount decrease if I reduce the amount of "installed" memory in the VM? What steps can I take to reduce the system's memory footprint without incurring an increase in paging file usage?

  Read the article

• PHP/MySQL Performance Testing with Just PHP

  - by Mike Gifford

  I'm trying to diagnose a server where the website is loading very slowly, but unfortunately my client has only provided me with FTP access. I've got FTP access so I can upload PHP scripts, but can't set up any other server side tools. I have access to phpMyAdmin, but not direct access to the MySQL server. It is also unfortunately a Windows server (and we've been a Linux shop for over a decade now). So, if I wan to evaluate MySQL & disk speed performance through PHP on a generic server, what is the best way to do this? There are already tools like: https://github.com/raphaelm/php-benchmark or https://github.com/InfinitySoft/php-benchmark But I'm surprised there isn't something that someone has already set up & configured to just run through and do some basic testing of a server's responsiveness. Every time we evaluate a new server environment it's handy to be able to compare it to an existing one quickly to see if there are any anomalies. I guess I'd just hoped that someone else had written up a script to do this already. I know I have, but that was before Github when there was a handy place to post scraps of code like this. Originally posted in http://stackoverflow.com/questions/12321498/php-mysql-performance-testing-with-just-php but it was recommended that I re-post it here.

  Read the article

• Refresh file access time under Linux / Discard disk read cache

  - by calandoa

  I am making use of the access time to analyse some build process, but it is not working the way I want: the access time is updated the first time I read the file, then it stays the same for a long while, or until the next reboot. For instance: $ ll -u some_file -rw-r--r-- 1 root root 1.3M 2010-04-07 10:03 some_file $ grep abcdef some_file $ ll -u some_file -rw-r--r-- 1 root root 1.3M 2010-04-07 11:24 some_file # The access time is updated # waiting a few minutes... $ grep abcdef some_file $ ll -u some_file -rw-r--r-- 1 root root 1.3M 2010-04-07 11:24 some_file # The access time has not been updated :( I suppose that the file is buffered by Linux in the free memory, the only this copy is accessed the subsequent times for speed reasons. A solution would be to discard the buffers in memory. After searching some forums, I found: sync echo 1 > /proc/sys/vm/drop_caches echo 2 > /proc/sys/vm/drop_caches echo 3 > /proc/sys/vm/drop_caches But it is not working, it seems that it only sync up the write buffers, not the read ones. May be it is due to some custom kernel configuration on my distro (fedora 9)? Or I am missing something here? Is there a way to achieve this access time refresh? Note also that I do not want to simulate some writes on my entire file tree. Because I am using some makefile based build system, this will cause the entire project to be build again.

  Read the article

• Two large, linked Excel files take 30 minutes to save, except in VMWare environment

  - by Gerald L

  I support some tax consultants who love to use Excel when they should probably be using Access. Anyway, they have created two Excel files, A and B. File B has cells linked to file A. File A is 27 MB and file B is 16 MB. One worksheet has roughly 1 million rows and there is another worksheet doing a whole bunch of SUMIF on the 1 million rows. Not the best idea, but whatever. Both Excel files open and recalculate within a reasonable amount of time (1-2 minutes). For a files that large, this is acceptable. Here is the problem: Once you change a cell, and save the file B, it takes a solid 30 minutes to save the file, and the processors are going full speed. I've tried this on 6 different machines, all running Windows XP SP3 with Office 2007 SP2 and all patches. The specs vary from one machine with 512 MB or RAM to a machine with 4 GB of RAM and quad processors. Same result every time. Here is the clincher: If I do this same save operation on a VMWare virtual machine, the file gets saved in 1 minute. I've tried this with my ESX servers at the office, my Mac Fusion at home, and VMWare workstation at the office. It does not matter how much RAM the virtual machine has... it saves in about 1 minute every time. Does anybody have any idea why this is happening and how to fix?

  Read the article

• Overclock Failed

  - by John

  This morning when I tried to turn on my computer, the monitor would not display anything. The computer is on, but no UI on the monitor and no beep. I turned off the computer and turn it back on again. This time, the computer was on for about 2 seconds and automatically turned itself off for about 2 second and automatically turned itself back on. This happened two times without the monitor displaying any UI. On the third try, the computer did the same thing but when it turned itself back on, the monitor displayed this: American Megatrends Asus P8P67 Le ACPI bios Revision 1011 CPU Intel Core i5 2500K CPU @ 3.30GHz Speed: 3300MHz Total Memory 4096 MB (DDR3-1333) USB Devices Total: 0 Drive, 1 Keyboard, 1 Mouse, 2 Hubs Detected ATA/ATAPI Deivces SATA6G_2 Hitachi HDs821010CLA 332 SATA3G_1 Corsair force 3 SSD SATA3G_2 HL-DT-ST DB-RE UH12CS28 Overclocking Failed! Please enter setup to reconfigure your system. Press F1 to Run Setup. After I pressed F1, it went into the Asus EF1 Bios Utility. I couldn't do anything in there so I just exited. After which, the computer auto turned off and on again and I was able to use the PC like regular. This has never happened to this computer before and the day before, nothing seemed wrong, just regular use and some gaming.

  Read the article

• Basic multicast network performance problems

  - by davedavedave

  I've been using mpong from 29west's mtools package to get some basic idea of multicast latency across various Cisco switches: 1Gb 2960G, 10Gb 4900M and 10Gb Nexus N5548P. The 1Gb is just for comparison. I have the following results for ~400 runs of mpong on each switch (sending 65536 "ping"-like messages to a receiver which then sends back -- all over multicast). Numbers are latencies measured in microseconds. Switch Average StdDev Min Max 2960 (1Gb) 109.68463 0.092816 109.4328 109.9464 4900M (10Gb) 705.52359 1.607976 703.7693 722.1514 NX 5548(10Gb) 58.563774 0.328242 57.77603 59.32207 The result for 4900M is very surprising. I've tried unicast ping and I see the 4900 has ~10us higher latency than the N5548P (average 73us vs 64us). Iperf (with no attempt to tune it) shows both 10Gb switches give me 9.4Gbps line speed. The two machines are connected to the same switch and we're not doing any multicast routing. OS is RHEL 6. 10Gb NICs are HP 10GbE PCI-E G2 Dual-port NICs (I believe they are rebranded Mellanox cards). The 4900 switch is used in a project with tight access control so I'm waiting for approval before I can access it and check the config. The other two I have full access to configure. I've looked at the Cisco document[2] detailing differences between NX-OS and IOS w.r.t multicast so I've got some ideas to try out but this isn't an area where I have much expertise. Does anyone have any idea what I should be looking at once I get access to the switch? [1] http://docwiki.cisco.com/wiki/Cisco_NX-OS/IOS_Multicast_Comparison

  Read the article

• Why is the link between my switch and my router always negotiating half-duplex mode?

  - by Massimo

  I have a Cisco 2950 switch which has one of its ports connected to an Internet router provided by my ISP; I have no access to the router configuration, but I manage the switch. If I leave all switch ports with their default setup (auto-negotiation of speed and duplex mode), this link always connects at 100 MBit/s, but in half-duplex mode. I've tried replacing the cable, and also moving the link to another switch port: the result is always the same. A different device connected to the same port (or to any switch port, really) shows no problem at all. It could be guesed that someone configured the router to only connect in half-duplex mode... BUT, here's the catch: if I manually force the switch port to full-duplex mode (duplex full in the interface configuration), the link goes up, stays up and is completely stable. So: The connection is not forced to half-duplex mode by the router, otherwise it would not connect at all if I force the switch end to full-duplex. There is no actual link problem, otherwise the full-duplex connection would not go up or would at least show some errors. But if I leave the port free to auto-negotiate, it always connects in half-duplex mode. Why?

  Read the article

• Embedding a WMV file on the web via URL in a Powerpoint presentation

  - by Dave

  I've got a situation where I want to distribute a Powerpoint presentation to several people. I want to be able to embed several large videos in this presentation by linking to a URL, for the following specific reasons: the videos are highly confidential, and I would like to be able to delete them at some later date, but still allow them to see it in the presentation while it is online. I want to send the presentation via email (so it should be small), and put the links on a server with a faster upload speed Maybe I'd like to change the video at some point without changing the presentation One option that addresses #1 is to hook up a webcam and allow them to see video stream from the office, but our upload rate is too slow for this to be a viable option. I've tried embedding a video and giving Powerpoint the URL. It seems to work initially, because the first frame appears in my slideshow. However, when I play the slideshow, nothing happens. I looked at the network traffic on my computer, and nothing was getting downloaded from the remote server. Any suggestions on how to make this work, or how to at least satisfy the criteria listed above would be great!

  Read the article

• 32 core (each physical core) 2.2 GhZ or 12 core (6 physical cores) 3.0GHZ?

  - by Tejaswi Rana

  I am working on a multithreaded application (Forex trading app built on C#) and had the client upgrade from the 12 core 3.0GHZ machine (Intel) to a 32 core 2.2 Ghz machine (AMD). The PassMark benchmark results were significantly higher when using multicores doing Integer, Floating and other calculations while for a single core calculation it was a bit slower than the pack (others that were being compared to with similar config as the 12 core one). Oh it also comes with 64 GB RAM (4 times as the other one) and a much faster SSD. So after configuring and running the application on that machine, not only did it not perform as well, it was significantly slower. We're talking about 30seconds - 1 minute slower on an app that usually completes processing within 5-20 secs. The application uses MAX DEGREE of PARALLELISM (TPL) which I've tried setting to number of cores and also half of that. I've also tried running single threaded and without setting any limits in parallel threading. While it may be the hardware has some issues, I am wondering if the CPU processing speed is the issue. I can overclock to 3.0 GHZ. But is that even a good idea? Server Info - AMD http://www.passmark.com/forum/showthread.php?4013-AMD-Dual-6272-performance-is-60-lower-than-benchmarks Seems that benchmark was wrong to start with - officially. Intel i7 3930k OS (same in both) Windows 7 Professional 64-bit

  Read the article

• How to prioritize openvpn traffic?

  - by aditsu

  I have an openvpn server, with one network interface. VPN traffic is extremely slow. I tried to do traffic control with this configuration (currently): qdisc del dev eth0 root qdisc add dev eth0 root handle 1: htb default 12 class add dev eth0 parent 1: classid 1:1 htb rate 900mbit #vpn class add dev eth0 parent 1:1 classid 1:10 htb rate 1500kbit ceil 3000kbit prio 1 #local net class add dev eth0 parent 1:1 classid 1:11 htb rate 10mbit ceil 900mbit prio 2 #other class add dev eth0 parent 1:1 classid 1:12 htb rate 500kbit ceil 1000kbit prio 2 filter add dev eth0 protocol ip parent 1:0 prio 1 u32 match ip sport 1194 0xffff flowid 1:10 filter add dev eth0 protocol ip parent 1:0 prio 2 u32 match ip dst 192.168.10.0/24 flowid 1:11 qdisc add dev eth0 parent 1:10 handle 10: sfq perturb 10 qdisc add dev eth0 parent 1:11 handle 11: sfq perturb 10 qdisc add dev eth0 parent 1:12 handle 12: sfq perturb 10 But it's still extremely slow. I have an imaps connection that keeps transferring data continuously (I successfully limited the rate) but with openvpn I can't seem to get more than about 100kbit/s The internet connection speed is about 3mbit/s (symmetric) What could be the problem? Does the sport filter work for udp?

  Read the article

• httpd.config Easy Apache WHM CentOS

  - by jessie

  First let me explain how I got to this situation. I run a Streaming Video Site. Videos are about 100-250MB in size at any given time there are 500 people on the site. So I guess that would make then static. Recently My site started getting really slow and the only way to fix it temporarily was to restart apache. Now there was no change in traffic that could have caused this. My site is not being attacked. My hosting company recomended to implement mpm_mod and suPHP. They did that by using Easy Apache in WHMS. Then everything was working fine but a little slow. I researched around and to my understanding that mpm will do that but be more table. I was told that installing FastCGI would speed things up just enough. Well that made everything worse. The site is slow and time's out. I used WHM and took off fastCGI but its still the same, it seems like everything i do as of now nothing changes. I even did a roll back on the htconfig file but that didn't work. I'm not sure how to fix this. and my hosting network guy wont be able to touch the problem until Tuesday. I have root access.

  Read the article

• Pitfalls to using Gluster as a home/profile directory server?

  - by Bart Silverstrim

  I was asking recently about options for divvying up access to file servers, as we have a NAS solution that gets fairly bogged down when our users (with giant profiles, especially) all log in nearly simultaneously. I ran across Gluster and it looks like it can cluster different physical storage media into a single virtual volume and share it out like a virtual NAS from the client perspective and it support CIFS. My question is whether something like this would be feasible to use for home and profile directories in an active directory environment. I was worried about ACL's, primarily, as I didn't think CIFS was fine-grained enough to support NTFS permissions and it didn't look like Gluster exports those permission levels, just the base permissions for basic file sharing. I got the impression that using Gluster would allow for data to be redundant across multiple servers and would speed up access to the files under heavy load, while allowing us to dynamically boost storage capacity by just adding another server and telling Gluster's master node to add that server. Maybe I'm wrong with my understanding of it though. Anyone else use it or care to share how feasible this is?

  Read the article

• Rsync when run in cron doesnt work. Rsync between Mac Os x Server and Linux Centos

  - by Brady

  I have a working rsync setup between Mac OS X Server and Linux Centos when run manually in a terminal. I enter the rsync command, it asks for the password, I enter it and off it goes, runs and completes. Now I know thats working I set out to fully automate it via cron. First off I create an SSH authorized key by running this command on the Mac server: ssh-keygen -t dsa -b 1024 -f /Users/admin/Documents/Backup/rsync-key Entering the password and then confirming it. I then copy the rsync-key.pub file accross to the linux server and place in the rsync user .ssh folder and rename to authorized_keys: /home/philosophy/.ssh/authorized_keys I then make sure that the authorized_keys file is chmod 600 in the folder chmod 700. I then setup a shell script for cron to run: #!/bin/bash RSYNC=/usr/bin/rsync SSH=/usr/bin/ssh KEY=/Users/admin/Documents/Backup/rsync-key RUSER=philosophy RHOST=example.com RPATH=data/ LPATH="/Volumes/G Technology G Speed eS/Backup" $RSYNC -avz --delete --progress -e "$SSH -i $KEY" "$LPATH" $RUSER@$RHOST:$RPATH Then give the shell file execute permissions and then add the following to the crontab using crontab -e: 29 12 * * * /Users/admin/Documents/Backup/backup.sh I check my crontab log file after the above command should run and I get this in the log and nothing else: Feb 21 12:29:00 fileserver /usr/sbin/cron[80598]: (admin) CMD (/Users/admin/Documents/Backup/backup.sh) So I asume everything has run as it should. But when I check the remote server no files have been copied accross. If I run the backup.sh file in a terminal as normal it still prompts for a password but this time its through the Mac Key chain system rather than typing into the console window. With the Mac Key Chain I can set it to save the password so that it doesnt ask for it again but Im sure when run with cron this password isnt picked up. This is where I'm asuming where rsync in cron is failing because it needs a password to connect but I thought the whole idea of making the SSH keys was to prevent the use of a password. Have I missed a step or done something wrong here? Thanks Scott

  Read the article

• Why are my socks proxies slow

  - by vps_newcomer

  I have a linux vps, and i have tried a few socks proxy setups to test their performance: All tests were using speedtest.net The standard ssh tunnel proxy 0.8mbit/s download and 0.1-0.2mbit/s upload speeds dante-server proxy 1.3mbit/s download and 0.4-0.5mbit/s upload I am wondering why are these speeds so slow? Is anything shaping them? Is it just the nature of socks proxies? I know that the ssh tunnel has to do encryption and what not so that is why its slow, but i was surprised to see that the second setup was also quite slow. On the VPS i have received download speeds of 25MB/s per second (thats about 200mbit/s and upload speed of atleast 5MB/s (haven't got a good enough pipe to test anything faster). The other option i was going to try is to setup OpenVPN and see how that goes, however i need to find a good tutorial as it's fairly complicated to setup. So why is it so slow? How can i test to see where the bottleneck is? How can i make it faster :D

  Read the article

• How can I regain control over a "stuck" scroll bar?

  - by jonsca

  I normally have a lot of tabs open in the browser at one time, which normally doesn't cause any problems. Occasionally, though, the page will have fully rendered, the scroll bar is at the top of its track on the right, but placing the the mouse pointer on the scroll bar does not allow me to get control of it (and using the arrow at the bottom of the scroll bar doesn't work either). This seems to happen to me in both Firefox and Chrome, both latest versions. There is normally no load on the CPU, and while my memory usage can be high (especially with Chrome), I still usually have 25% left. I fear that this is one of those "for your own good" features, to prevent scrolling down a page that may still have elements loading and/or a stuck script, but I'm wondering whether or not there is a setting in Firefox or Chrome (or perhaps Windows in general) that will allow the scroll bar to be "released" even though the browser may be busy? It may be "2002" of me, but I wouldn't mind being able to scroll along gradually, even if the page hasn't had time to fully render all of the images, etc., yet. Does such an advanced setting exist "under the hood"?

  Read the article

• Are applications optimized for XenApp?

  - by damitamit

  Our IT dept are about to deploy virtualized apps using Citrix XenApp. One of these apps will be Dynamics AX 4.0 SP2, a ERP client (which I develop on). They have supposedly reached a roadblock because an external 'Dynamics AX Consultant' has told our IT Dept that Dynamics 4 will not work optimally on Citrix and will run very slow because it is not optimized for Citrix. We have it running in a Test environment now and seems ok. They have been told that the only 'solution' is to upgrade to Dynamics AX 2009 where supposedly this problem as been fixed. (not a small task for my team!) When I heard about this, I was quite surprised. From my brief knowledge of Citrix, I thought it would be application independent. How does the citrix app virtualization work, in that a particular app would work better than others on citrix? Would the speed of the virtualized app not just depend on the resources/network connection the citrix server has? FYI, Dynamics AX is a 3-tier client/server system, so the client will be accessing a AOS application server, which then accesses the database. Please enlighten me :)

  Read the article

• Dedicated server with a lot of storage and good support - and cost-effective

  - by Martin Burger

  Hello, I am from Germany and looking for a dedicated server located in the US with a lot of storage: 750 - 1500 GB. CPU speed and amount of memory are secondary, the server will host large amounts of media files via http and ftp - the basic task is to help people exchange media files. In Germany, there are some good offers, like "Root Server EQ6" at www.hetzner.de. For example, that company provides support of high quality, and their plans are very cost-effective. The plan mentioned above costs about $90 per month and provides two 1500 GB SATA-II HDDs (Software-RAID 1). In the US, I found (amongst others) Go Daddy and rackspace. Go Daddy offers some "Storage Monster" plans that include 2 x 1,000 GB hard drives for about $180 per month - already twice as much as Hetzner above. However, I found some blog and forum entries that complain about the support provided by Go Daddy. Rackspace seems to provide decent support, but they are very "upscale". Their dedicated servers are customizable and start at $419 - thus, about 4.5 times as much as Hetzner. Can anybody recommend a solution / plan that is comparable to the one by Hetzner? Or are prices for dedicated servers in general much higher than in Germany? Regards, Martin

  Read the article

< Previous Page | 294 295 296 297 298 299 300 301 302 303 304 305  | Next Page >