Search Results

Search found 17911 results on 717 pages for 'load balancing'.

Page 3/717 | < Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >

• Cisco Catalyst 3550 + Alteon 184 Load-Balancing Issues

  - by upkels

  I have just deployed a couple Cisco Catalyst 3550 switches, and a couple Alteon 184 Web Switches for load-balancing. I can ping all RIPs and VIPs to/from the Alteon. Topology Before: (server) <- (Alteon) <- (Internet) Topology Now: (server) <- (3550) <- Alteon <- (Internet) Cisco Port Configuration (Alteon Uplink Port): description LB_1_PORT_9_PRIMARY switchport access vlan 10 switchport mode access switchport nonegotiate speed 100 duplex full Alteon Port 9 Configuration (VLAN 10 WAN): >> Main# /c/port 9/cur Current Port 9 configuration: enabled pref fast, backup gig, PVID 10, BW Contract 1024 name UPLINK >> Main# /c/port 9/fast/cur Current Port 9 Fast link configuration: speed 100, mode full duplex, fctl none, auto off Cisco Configuration (Load-Balanced Servers Port): description LB_1_PORT_1_PRIMARY switchport access vlan 30 switchport mode access switchport nonegotiate speed 100 duplex full Alteon Port 1 Configuration (VLAN 30 LOAD-BALANCED LAN): >> Main# /c/port 1/cur Current Port 1 configuration: enabled pref fast, backup gig, PVID 30, BW Contract 1024 name LB_PORT_1 >> Main# /c/port 1/fast/cur Current Port 1 Fast link configuration: speed 100, mode full duplex, fctl both, auto on Each of my servers are on vlan 10 and 30, properly communicating. I have tried to turn on VLAN tagging on the Alteon, however it seems to cause all communications to stop working. When I tcpdump -i vlan30 on any of the webservers, I see normal ARP communications, and some STP communications, which may or may not be part of the problem: ... 15:00:51.035882 STP 802.1d, Config, Flags [none], bridge-id 801e.00:11:5c:62:fe:80.8041, length 42 15:00:51.493154 IP 10.1.1.254.33923 > 10.1.1.1.http: Flags [S], seq 707324510, win 8760, options [mss 1460], length 0 15:00:51.493336 IP 10.1.1.1.http > 10.1.1.254.33923: Flags [S.], seq 3981707623, ack 707324511, win 65535, options [mss 1460], len gth 0 15:00:51.493778 ARP, Request who-has 10.1.3.1 tell 10.1.3.254, length 46 etc... I'm not sure if I've provided enough information, so please let me know if any more is necessary. Thank you!

  Read the article

• Is it possible to load balance requests from a single source?

  - by Shawn

  In our application, Server A establishes a TCP connection with Server B, then it sends a large amount of requests to Server B over the TCP connection. The request message is XML-based. Server B needs to respond within a very short period, and it takes time to process the requests. So we hope a load balancer can be introduced and we can expedite the processing by using multiple Server B's. This is not a web application. I did some research but failed to find a similar application of load balancer. Can anyone tell me if there's a load balancer can help in our application?

  Read the article

• load balancer question c# asp.net

  - by Migs

  The place where I work has 2 servers and a load balancer. The setup is horrible since I have to manually make sure both servers have the same files. I know there are ways to automate this but it has not been implemented, hopefully soon (I have no control over this). I wrote an application that collects a bunch of information from a user, then creates a folder named after the email of the user in one of the servers. The problem is that I can't control in which server the folder gets created in, so let say a user goes in.. fills his stuff and his folder gets created in server 1, user goes away for a while and goes back to the site but this time the load balancer throws the user into server 2, now the user does something that needs to be saved into his folder but since it didn't created in this server an error occurs. What can I do about this? any suggestions? Thanks

  Read the article

• High Server Load cannot figure out why

  - by Tim Bolton

  My server is currently running CentOS 5.2, with WHM 11.34. Currently, we're at 6.43 to 12 for a load average. The sites that we're hosting are taking a lot time to respond and resolve. top doesn't show anything out of the ordinary and iftop doesn't show a lot of traffic. We have many resellers, and some not so good at writing code, how can we find the culprit? vmstat output: vmstat procs -----------memory---------- ---swap-- -----io---- --system-- -----cpu------ r b swpd free buff cache si so bi bo in cs us sy id wa st 0 2 84 78684 154916 1021080 0 0 72 274 0 14 6 3 80 12 0 top output (ordered by %CPU) top - 21:44:43 up 5 days, 10:39, 3 users, load average: 3.36, 4.18, 4.73 Tasks: 222 total, 3 running, 219 sleeping, 0 stopped, 0 zombie Cpu(s): 5.8%us, 2.3%sy, 0.2%ni, 79.6%id, 11.8%wa, 0.0%hi, 0.2%si, 0.0%st Mem: 2074580k total, 1863044k used, 211536k free, 174828k buffers Swap: 2040212k total, 84k used, 2040128k free, 987604k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 15930 mysql 15 0 138m 46m 4380 S 4 2.3 1:45.87 mysqld 21772 igniteth 17 0 23200 7152 3932 R 4 0.3 0:00.02 php 1586 root 10 -5 0 0 0 S 2 0.0 11:45.19 kjournald 21759 root 15 0 2416 1024 732 R 2 0.0 0:00.01 top 1 root 15 0 2156 648 560 S 0 0.0 0:26.31 init 2 root RT 0 0 0 0 S 0 0.0 0:00.35 migration/0 3 root 34 19 0 0 0 S 0 0.0 0:00.32 ksoftirqd/0 4 root RT 0 0 0 0 S 0 0.0 0:00.00 watchdog/0 5 root RT 0 0 0 0 S 0 0.0 0:02.00 migration/1 6 root 34 19 0 0 0 S 0 0.0 0:00.11 ksoftirqd/1 7 root RT 0 0 0 0 S 0 0.0 0:00.00 watchdog/1 8 root RT 0 0 0 0 S 0 0.0 0:01.29 migration/2 9 root 34 19 0 0 0 S 0 0.0 0:00.26 ksoftirqd/2 10 root RT 0 0 0 0 S 0 0.0 0:00.00 watchdog/2 11 root RT 0 0 0 0 S 0 0.0 0:00.90 migration/3 12 root 34 19 0 0 0 R 0 0.0 0:00.20 ksoftirqd/3 13 root RT 0 0 0 0 S 0 0.0 0:00.00 watchdog/3 top output (ordered by CPU time) top - 21:46:12 up 5 days, 10:41, 3 users, load average: 2.88, 3.82, 4.55 Tasks: 217 total, 1 running, 216 sleeping, 0 stopped, 0 zombie Cpu(s): 3.7%us, 2.0%sy, 2.0%ni, 67.2%id, 25.0%wa, 0.0%hi, 0.1%si, 0.0%st Mem: 2074580k total, 1959516k used, 115064k free, 183116k buffers Swap: 2040212k total, 84k used, 2040128k free, 1090308k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ TIME COMMAND 32367 root 16 0 215m 212m 1548 S 0 10.5 62:03.63 62:03 tailwatchd 1586 root 10 -5 0 0 0 S 0 0.0 11:45.27 11:45 kjournald 1576 root 10 -5 0 0 0 S 0 0.0 2:37.86 2:37 kjournald 27722 root 16 0 2556 1184 800 S 0 0.1 1:48.94 1:48 top 15930 mysql 15 0 138m 46m 4380 S 4 2.3 1:48.63 1:48 mysqld 2932 root 34 19 0 0 0 S 0 0.0 1:41.05 1:41 kipmi0 226 root 10 -5 0 0 0 S 0 0.0 1:34.33 1:34 kswapd0 2671 named 25 0 74688 7400 2116 S 0 0.4 1:23.58 1:23 named 3229 root 15 0 10300 3348 2724 S 0 0.2 0:40.85 0:40 sshd 1580 root 10 -5 0 0 0 S 0 0.0 0:30.62 0:30 kjournald 1 root 17 0 2156 648 560 S 0 0.0 0:26.32 0:26 init 2616 root 15 0 1816 576 480 S 0 0.0 0:23.50 0:23 syslogd 1584 root 10 -5 0 0 0 S 0 0.0 0:18.67 0:18 kjournald 4342 root 34 19 27692 11m 2116 S 0 0.5 0:18.23 0:18 yum-updatesd 8044 bollingp 15 0 3456 2036 740 S 1 0.1 0:15.56 0:15 imapd 26 root 10 -5 0 0 0 S 0 0.0 0:14.18 0:14 kblockd/1 7989 gmailsit 16 0 3196 1748 736 S 0 0.1 0:10.43 0:10 imapd iostat -xtk 1 10 output [root@server1 tmp]# iostat -xtk 1 10 Linux 2.6.18-53.el5 12/18/2012 Time: 09:51:06 PM avg-cpu: %user %nice %system %iowait %steal %idle 5.83 0.19 2.53 11.85 0.00 79.60 Device: rrqm/s wrqm/s r/s w/s rkB/s wkB/s avgrq-sz avgqu-sz await svctm %util sda 1.37 118.83 18.70 54.27 131.47 692.72 22.59 4.90 67.19 3.10 22.59 sdb 0.35 39.33 20.33 61.43 158.79 403.22 13.75 5.23 63.93 3.77 30.80 Time: 09:51:07 PM avg-cpu: %user %nice %system %iowait %steal %idle 1.50 0.00 0.50 24.00 0.00 74.00 Device: rrqm/s wrqm/s r/s w/s rkB/s wkB/s avgrq-sz avgqu-sz await svctm %util sda 0.00 25.00 2.00 2.00 128.00 108.00 118.00 0.03 7.25 4.00 1.60 sdb 0.00 16.00 41.00 145.00 200.00 668.00 9.33 107.92 272.72 5.38 100.10 Time: 09:51:08 PM avg-cpu: %user %nice %system %iowait %steal %idle 2.00 0.00 1.50 29.50 0.00 67.00 Device: rrqm/s wrqm/s r/s w/s rkB/s wkB/s avgrq-sz avgqu-sz await svctm %util sda 0.00 95.00 3.00 33.00 12.00 480.00 27.33 0.07 1.72 1.31 4.70 sdb 0.00 14.00 1.00 228.00 4.00 960.00 8.42 143.49 568.01 4.37 100.10 Time: 09:51:09 PM avg-cpu: %user %nice %system %iowait %steal %idle 13.28 0.00 2.76 21.30 0.00 62.66 Device: rrqm/s wrqm/s r/s w/s rkB/s wkB/s avgrq-sz avgqu-sz await svctm %util sda 0.00 21.00 1.00 19.00 16.00 192.00 20.80 0.06 3.55 1.30 2.60 sdb 0.00 36.00 28.00 181.00 124.00 884.00 9.65 121.16 617.31 4.79 100.10 Time: 09:51:10 PM avg-cpu: %user %nice %system %iowait %steal %idle 4.74 0.00 1.50 25.19 0.00 68.58 Device: rrqm/s wrqm/s r/s w/s rkB/s wkB/s avgrq-sz avgqu-sz await svctm %util sda 0.00 20.00 3.00 15.00 12.00 136.00 16.44 0.17 7.11 3.11 5.60 sdb 0.00 0.00 103.00 60.00 544.00 248.00 9.72 52.35 545.23 6.14 100.10 Time: 09:51:11 PM avg-cpu: %user %nice %system %iowait %steal %idle 1.24 0.00 1.24 25.31 0.00 72.21 Device: rrqm/s wrqm/s r/s w/s rkB/s wkB/s avgrq-sz avgqu-sz await svctm %util sda 0.00 75.00 4.00 28.00 16.00 416.00 27.00 0.08 3.72 2.03 6.50 sdb 2.00 9.00 124.00 17.00 616.00 104.00 10.21 3.73 213.73 7.10 100.10 Time: 09:51:12 PM avg-cpu: %user %nice %system %iowait %steal %idle 1.00 0.00 0.75 24.31 0.00 73.93 Device: rrqm/s wrqm/s r/s w/s rkB/s wkB/s avgrq-sz avgqu-sz await svctm %util sda 0.00 24.00 1.00 9.00 4.00 132.00 27.20 0.01 1.20 1.10 1.10 sdb 4.00 40.00 103.00 48.00 528.00 212.00 9.80 105.21 104.32 6.64 100.20 Time: 09:51:13 PM avg-cpu: %user %nice %system %iowait %steal %idle 2.50 0.00 1.75 23.25 0.00 72.50 Device: rrqm/s wrqm/s r/s w/s rkB/s wkB/s avgrq-sz avgqu-sz await svctm %util sda 0.00 125.74 3.96 46.53 15.84 689.11 27.92 0.20 4.06 2.41 12.18 sdb 2.97 0.00 91.09 84.16 419.80 471.29 10.17 85.85 590.78 5.66 99.11 Time: 09:51:14 PM avg-cpu: %user %nice %system %iowait %steal %idle 0.75 0.00 0.50 24.94 0.00 73.82 Device: rrqm/s wrqm/s r/s w/s rkB/s wkB/s avgrq-sz avgqu-sz await svctm %util sda 0.00 88.00 1.00 7.00 4.00 380.00 96.00 0.04 4.38 3.00 2.40 sdb 3.00 7.00 111.00 44.00 540.00 208.00 9.65 18.58 581.79 6.46 100.10 Time: 09:51:15 PM avg-cpu: %user %nice %system %iowait %steal %idle 11.03 0.00 3.26 26.57 0.00 59.15 Device: rrqm/s wrqm/s r/s w/s rkB/s wkB/s avgrq-sz avgqu-sz await svctm %util sda 0.00 145.00 7.00 53.00 28.00 792.00 27.33 0.15 2.50 1.55 9.30 sdb 1.00 0.00 155.00 0.00 800.00 0.00 10.32 2.85 18.63 6.46 100.10 [root@server1 tmp]# MySQL Show Full Processlist mysql> show full processlist; +------+---------------+-----------+-----------------------+----------------+------+----------------------------+----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------+ | Id | User | Host | db | Command | Time | State | Info | +------+---------------+-----------+-----------------------+----------------+------+----------------------------+----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------+ | 1 | DB_USER_ONE | localhost | DB_ONE | Query | 3 | waiting for handler insert | INSERT DELAYED INTO defers (mailtime,msgid,email,transport_method,message,host,ip,router,deliveryuser,deliverydomain) VALUES(FROM_UNIXTIME('1355879748'),'1TivwL-0003y8-8l','[email protected]','remote_smtp','SMTP error from remote mail server after initial connection: host mx1.mail.tw.yahoo.com [203.188.197.119]: 421 4.7.0 [TS01] Messages from 75.125.90.146 temporarily deferred due to user complaints - 4.16.55.1; see http://postmaster.yahoo.com/421-ts01.html','mx1.mail.tw.yahoo.com','203.188.197.119','lookuphost','','') | | 2 | DELAYED | localhost | DB_ONE | Delayed insert | 52 | insert | | | 3 | DELAYED | localhost | DB_ONE | Delayed insert | 68 | insert | | | 911 | DELAYED | localhost | DB_ONE | Delayed insert | 99 | Waiting for INSERT | | | 993 | DB_USER_TWO | localhost | DB_TWO | Sleep | 832 | | NULL | | 994 | DB_USER_ONE | localhost | DB_ONE | Query | 185 | Locked | delete from failures where FROM_UNIXTIME(UNIX_TIMESTAMP(NOW())-1296000) > mailtime | | 1102 | DB_USER_THREE | localhost | DB_THREE | Query | 29 | NULL | commit | | 1249 | DB_USER_FOUR | localhost | DB_FOUR | Query | 13 | NULL | commit | | 1263 | root | localhost | DB_FIVE | Query | 0 | NULL | show full processlist | | 1264 | DB_USER_SIX | localhost | DB_SIX | Query | 3 | NULL | commit | +------+---------------+-----------+-----------------------+----------------+------+----------------------------+----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------+ 10 rows in set (0.00 sec)

  Read the article

• ECMP Load Balancing in JUNOS

  - by SpacemanSpiff

  I'm trying to figure out how to use ECMP load balancing in JUNOS. I know this isn't the best way to load balance, but its quick and dirty and gets done what I need to. In ScreenOS this was pretty easy. Device: SRX220 JunOS: 10.3R2.11 Here's what I've got so far: routing-options { static { route 0.0.0.0/0 { next-hop [ 1.1.1.1 1.1.1.2 ]; metric 10; } } maximum-paths 2; Will that do it? Tom

  Read the article

• Windows Load-Balancing, Forward-Proxying Software

  - by LandonC

  Does anyone know of any Windows software that will do forward-proxying load-balancing, like HAProxy does? There are tons of reverse-proxy solutions, but I can't find any that do what HAProxy does, that is, allows you to load-balance a group of forwarding-proxies. I have a proxy farm (don't ask) that I need to round-robin balance. HAProxy will do it, but is very unstable on Windows. Thoughts? I'd really appreciate it. And yes, this is an actual, production environment question.

  Read the article

• Predictive vs Least Connection Load Balancing Techniques

  - by Mani

  I have a windows based desktop application that communicates via TCP to the application servers. (windows 2003). No sticky sessions between client calls. We have exactly 2 servers to load balance and we are thinking to use a F5 hardware NLB. The application is a heavy load types, doing not much bussiness logic in the services but retrieving quite a big amount of data at most of the times. May be on an average 5000 to 10000 records at all times. Used mainly for storing and retirieving data and no special processing of data or calculations running on the server side. I am favouring 'predictive' considering my services take a while at times to return data and hence tracking the feedback would yield some better routing as in predictive. I am not sure if the given data is sufficient enough to suggest some ideas but considering these, what would be some suggestions\things to consider\best between Predictive and Least Connections ? Thanks.

  Read the article

• SQLServer 2008 FailOver and Load Balancing

  - by Jedi Master Spooky

  I have a project with a 2TB database ( 450.000.000 rows). I need to provide to the proyect a solution that gives FailOver and load Balacing, what do you recommend? We are going to use a NetApp Filer for the Data Files and for the File System of the Proyect. I read that SQl Clustering does not provide load balacing. If I cannnot have this feature and I have to go only to the FailOver what Server ( I presume that the key feature here is memory) would you recomend. We are adding 1.000.000 rows a day. Once the rows is inserted we are doing a lot of updates to that row for about 1 week then the row get static. Because of this I am thinking in some kind of history table or database or something like that. I am open to the Os servers implementation, I was thinking of a windows 2008 server with cluster but this depend of the database solution

  Read the article

• ECMP Load Balancing in JUNOS

  - by SpacemanSpiff

  I'm trying to figure out how to use ECMP load balancing in JUNOS. I know this isn't the best way to load balance, but its quick and dirty and gets done what I need to. In ScreenOS this was pretty easy. Device: SRX220 JunOS: 10.3R2.11 Here's what I've got so far: routing-options { static { route 0.0.0.0/0 { next-hop [ 1.1.1.1 1.1.1.2 ]; metric 10; } } maximum-paths 2; Will that do it? Tom

  Read the article

• Linux/bsd tcp load balancing with 10 gigabit ethernet

  - by user37899

  Okay, I've been looking at layer 4 load balancing solutions for 10 gigabit links. I need the following properties Works at 10Gig ethernet speeds. Can support long live tcp connections. up to 1mil live tcp connections. Balancer not involved in the return path. Fault tolerant with tcp session fail over. low latency and good through put. can be scripted. Either a software or hardware solution. Can it be done? Anyone doing this?

  Read the article

• apache, shibboleth, load balancing aliase, ssl

  - by Nikolaidis Fotis

  Good morning folks Could you give me a bit of help with the following problem ? I have a dns load balancing mechanism and an alias (hostAlias) which may point to host01, or host02 I want to configure apache and shibboleth to work with that alias. What happens is ... User types : https://hostAlias (it points to host01) apache host01 : redirect to shibboleth shibboleth host01 : redirect to **https://hostAlias.cern.ch/Shibboleth.sso/ADFS** Now, there are two cases. Either this time hostAlias will point again to host01 , or it will point to host02. If it points to host02, host01 will not get the anwser and the authentication fails. Also, about ssl certificates, I guess that each host will need its own certificate. right ? Should I need a certificate with DNS aliases ? Thanks in advance !

  Read the article

• Utilize two gateways on the same network same interface with load balancing

  - by RushPL

  My setup is two ISPs on a single interface and single network. I can either set my default gateway to 192.168.0.1 or 192.168.1.250 and either work. My desire is to utilize both of them with some load balancing. I have tried to follow the advice given in here http://serverfault.com/a/96586 #!/bin/sh ip route show table main | grep -Ev '^default' \ | while read ROUTE ; do ip route add table ISP1 $ROUTE done ip route add default via 192.168.1.250 table ISP1 ip route add default via 192.168.0.1 table ISP2 iptables -t mangle -A PREROUTING -j CONNMARK --restore-mark iptables -t mangle -A PREROUTING -m mark ! --mark 0 -j ACCEPT iptables -t mangle -A PREROUTING -j MARK --set-mark 10 iptables -t mangle -A PREROUTING -m statistic --mode random --probability 0.5 -j MARK --set-mark 20 iptables -t mangle -A PREROUTING -j CONNMARK --save-mark Now then I do "traceroute somehost" repeatedly I can only get route through my default route which is 192.168.1.250. Shouldn't the packets change routes in a random manner? How to debug it?

  Read the article

• Load balancing + NAT issue on BNT GBE 2-7 gear

  - by Clément Game

  Hi guys, I've got troubles configuring an Hardware load-Balancer with NAT functions. I have the following architecture: Internet === VIP (public) LB (private ip) ==== private addressed servers When a connection is initialised from the outside (internet) , the LB correctly forwards the SYN packet to one of the private servers. But when these servers want to reply with a SYN/ACK there is a problem. the initial SYN packet had as ip header : VIP = Private_server_Address But the private servers cannot reach VIP from their side (this is normal since it's nated), and then provide a correct reply. Have you guys any solution to correctly forward the packets to their correct destination ? Note: The load balancer, which is the default gw for the servers, also has a NAT rule for "masquerading" (actually more SNAT than real masquerading) Regards, Clément.

  Read the article

• Amazon EC2 Elastic Load Balancing - strategy for zero downtime server restart

  - by Yoga

  I have 5 web servers (Apache/mod_perl) behind Amazon EC2 Elastic Load Balancing, when I deploy codes to the web servers, I am doing this.. For each machine, shutdown the Apache Update the code Start over the server and proceed to the next server I think when my server is shutdown, ELB will not distribute request to my server, but how about the request still serving? I think a better approach is Stop accepting new request from ELB Sleep for sometimes, shutdown web server only if all requests are responded Update the codes Start the server again But how to perform (1) and (2) from my local sever? Do I need to use AWS API? or other easy way to do it? Thanks.

  Read the article

• PHP and load balancing

  - by StCee

  I have one major domain but the server spec behind it is not good enough. Hence I want to relay the traffic, in particular php-mysql queries to multiple smaller servers. How is that normally be done? (BTW I wonder how much traffic or number of php/mysql request a normal setup on ec2 micro instance can handle? ) I did have a look of EC2 load balancer. But is it only possible to load balance on machines of your own account?

  Read the article

• GlusterFs - high load 90-107% CPU

  - by Sara

  I try and try and try to performance and fix problem with gluster, i try all. I served on gluster webpages, php files, images etc. I have problem after update from 3.3.0 to 3.3.1. I try 3.4 when i think maybe fix it but still the same problem. I temporarily have 1 brick, but before upgrade will be fine. Config: Volume Name: ... Type: Replicate Volume ID: ... Status: Started Number of Bricks: 0 x 2 = 1 Transport-type: tcp Bricks: Brick1: ...:/... Options Reconfigured: cluster.stripe-block-size: 128KB performance.cache-max-file-size: 100MB performance.flush-behind: on performance.io-thread-count: 16 performance.cache-size: 256MB auth.allow: ... performance.cache-refresh-timeout: 5 performance.write-behind-window-size: 1024MB I use fuse, hmm "Maybe the high load is due to the unavailable brick" i think about it, but i cant find information on how to safely change type of volume. Maybe u know how?

  Read the article

• Amazon CloudFront and EC2: Global Load Balancing

  - by Matt Rogish

  We have an app that is going to store and serve up a decent amount of data in S3 to a global audience where latency should be minimized. So, we've been doing tests with Amazon CloudFront and have seen favorable results. However, we need a thin middleware layer (to do security etc.) and we'd like to put that in EC2. Due to security restrictions, this middleware layer will do the file streaming from S3/CloudFront: S3/CloudFront - EC2 - Clients We can geographically distribute the EC2 nodes (US East/West, and Ireland) but the problem is that a client in the EU would hit our US server and be fed data from there, thus rendering much of the performance benefit of CloudFront moot. I've been digging through the EC2 docs but I can't find a built-in way to get a geographically distributed version of EC2 a la CloudFront. Elastic Load Balancing sounds like the way to go, but I can't seem to find a way with that to direct based on routing... Preferably, we'd like to keep the amount of stuff outside of EC2/S3/etc. to a minimum (for obvious reasons). Any ideas how to do that within the EC2/S3 framework? DNS/routing tricks? Thanks!

  Read the article

• Apache, Tomcat and mod_jk for load balancing

  - by pHk

  Hi guys. I've set-up a basic Apache (2.2.x) and Tomcat (6.0.x) set-up using mod_jk for load balancing using the worker.properties file. Preliminary testing seems to show that this works relatively well, and it was quite easy to set-up. However; the fact that it was so easy to set-up has got me a little worried. We're dealing with 100 - 300 concurrent users using the same web application (deployed on 2 or 3 Tomcat instances). I have done a little Googling and looking around on here and there seems to be more than 1 way to accomplish this (one example on here used a balancer:// style URL, which I've never seen before in an Apache config). For example, one question I ask myself is how reliable the load detection on mod_jk really is (Busyness, Session, Request, etc). In your experience, does this set-up prove to be reliable in real world scenarios? Any pointers on improvements, pit falls or interesting literature/articles? I've worked with Apache before, but am in no way an expert. Thanks in advance.

  Read the article

• Nginx load balancing and maintaining URLs

  - by Steve Klabnik

  I'm trying to use nginx as a load balancer, and it's working great. One problem, though. The load balancing box is at 123.123.123.123, and the backend box is 456.456.456.456. So I have this config: upstream backend { server 456.456.456.456; } server { listen 80; server_name 123.123.123.123; access_log off; error_log off; location / { proxy_set_header Host $host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_pass http://backend; } } This works great. I hit 123.123.123.123 in my browser, and the page comes up. But now the URL in the browser says http://456.456.456.456. Do I need to use a rewrite rule or something to keep the url correct? I don't want it to be different when going to different backed servers. None of the tutorials I've read have mentioned anything about this.

  Read the article

• HAproxy roundrobin balancing does not appear to be distributing evently

  - by andrew

  Hello, I know that with loaded servers, roundrobin in HAproxy (1.4.4) does not evenly distribute, but my servers are currently getting NO traffic (test setup), and roundrobin balancing does www1,www1,www1,www1,www1,...www2,www2,www2,...,www1... I'm verifying this by having the script being run on each server cat /etc/HOSTNAME (slackware). I need to have it switch back and forth each time to test some session stuff (stored in shared memcached) but am having trouble getting it to switch between my two web servers on each request. global log 127.0.0.1 local0 warning maxconn 4096 chroot /usr/share/haproxy pidfile /var/run/haproxy.pid uid 99 gid 99 daemon defaults balance roundrobin fullconn 100 maxconn 4096 mode http option dontlognull option http-server-close option forwardfor option redispatch retries 3 timeout connect 5000 timeout client 20000 timeout server 60000 timeout queue 60000 stats enable stats uri /haproxy stats auth ***:*** frontend www *:80 log global acl is_upload hdr_dom(host) -i uploads.site.com acl is_api hdr_dom(host) -i api.site.com acl is_dev hdr_dom(host) -i dev.site.com acl is_apidev hdr_dom(host) -i apidev.site.com use_backend uploads.site.com if is_upload use_backend api.site.com if is_api use_backend dev.site.com if is_dev !is_apidev default_backend site.com backend site.com option httpchk HEAD /alive.php HTTP/1.1\r\nHost:site.com server www1 1.1.1.1:8080 weight 10 minconn 5 maxconn 25 check inter 2000 rise 2 fall 2 server www2 1.1.1.2:8080 weight 10 minconn 5 maxconn 25 check inter 2000 rise 2 fall 2 backend api.site.com option httpchk HEAD /alive.php HTTP/1.1\r\nHost:api.site.com server www1 1.1.1.1:8080 weight 10 minconn 5 maxconn 25 check inter 2000 rise 2 fall 2 server www2 1.1.1.2:8080 weight 10 minconn 5 maxconn 25 check inter 2000 rise 2 fall 2 backend dev.site.com option httpchk HEAD /alive.php HTTP/1.1\r\nHost:dev.site.com server www1 1.1.1.1:8080 weight 10 minconn 5 maxconn 25 check inter 2000 rise 2 fall 2 server www2 1.1.1.2:8080 weight 10 minconn 5 maxconn 25 check inter 2000 rise 2 fall 2 backend uploads.site.com option httpchk HEAD /alive.php HTTP/1.1\r\nHost:uploads.site.com server www1 1.1.1.1:8080 weight 10 minconn 5 maxconn 25 check inter 2000 rise 2 fall 2 server www2 1.1.1.2:8080 backup weight 10 minconn 5 maxconn 25 check inter 2000 rise 2 fall 2 So basically, I have some different back-ends (I've verified the ACLs are working), with the default option "roundrobin" selected. I've tried removing weights, removing the minconn/maxconn/fullconn attributes for all servers (not just the backend I'm testing), tried removing the ACLs, etc. I've been testing on dev.site.com BTW. Anyone see a reason why I can't get something like www1,www2,www1,www2,...? Also, this is one of my first questions on here, so please let me know if I left anything needed out of my post. Thanks!

  Read the article

• Add Machine Key to machine.config in Load Balancing environment to multiple versions of .net framework

  - by davidb

  I have two web servers behind a F5 load balancer. Each web server has identical applications to the other. There was no issue until the config of the load balancer changed from source address persistence to least connections. Now in some applications I receieve this error Server Error in '/' Application. Validation of viewstate MAC failed. If this application is hosted by a Web Farm or cluster, ensure that configuration specifies the same validationKey and validation algorithm. AutoGenerate cannot be used in a cluster. Description: An unhandled exception occurred during the execution of the current web request. Please review the stack trace for more information about the error and where it originated in the code. Exception Details: System.Web.HttpException: Validation of viewstate MAC failed. If this application is hosted by a Web Farm or cluster, ensure that configuration specifies the same validationKey and validation algorithm. AutoGenerate cannot be used in a cluster. Source Error: The source code that generated this unhandled exception can only be shown when compiled in debug mode. To enable this, please follow one of the below steps, then request the URL: Add a "Debug=true" directive at the top of the file that generated the error. Example: or: 2) Add the following section to the configuration file of your application: Note that this second technique will cause all files within a given application to be compiled in debug mode. The first technique will cause only that particular file to be compiled in debug mode. Important: Running applications in debug mode does incur a memory/performance overhead. You should make sure that an application has debugging disabled before deploying into production scenario. How do I add a machine key to the machine.config file? Do I do it at server level in IIS or at website/application level for each site? Does the validation and decryption keys have to be the same across both web servers or are they different? Should they be different for each machine.config version of .net? I cannot find any documentation of this scenario.

  Read the article

• load balancing between physical and virtual machines

  - by fefe

  First of all sorry if my question would be not relevant, I'm quite beginner. In short: I have 2 physical machines - first(Windows Server 2007, Apache 2.2) on the second machine esxi installed to host virtual machines . I have been converted my physical machine(1) on esxi(2) and in the next step I would like to deploy a load balancer between the physical and virtual machine. Would be this workaround appropriate? If yes what are the steps to follow?

  Read the article

• MySQL replication - Should I handle load balancing from my client code (PHP) ?

  - by pirostraktor

  In a MySQL master-slave replication enviroment if I have 4 slave servers how can I execute load balanced select queries? Should I write a PHP class to dealing with the 4 slaves or it is possible to address queries to MySQL's own load balancer solution? Is there a MySQL load balancing solutions? Can I use some other tool to distribute my queries? What is the typical set up in situations like this? Thanks for all answers!

  Read the article

• Pfsense: Inbound Load Balancing https with sticky connection

  - by Zeux

  first of all I'm very sorry for my English... This is my scenario: Internet Firewall+LB: pfsense_1(Active) + pfsense_2(Passive) in CARP Pool servers: 3 x nginx(PHP5+HTTP+HTTPS) Pfsense 1 and 2 CARP configured with Virtual IP (pubblic). Nginx servers's ips are all private. I want to load balance inbound HTTP and HTTPS connections between the 3 nginx web servers. An importat thing is that the HTTPS connections must be "sticky connections": in HTTPS connections, after login by username and password, I setup a php session and therefore when a client starts a HTTPS connection it will be always redirected to the same nginx server, until it disconnects itself, it closes the page/browser or after a timeout (30minutes?) without activity. Is this possible whit the last release(2.0.1) of pfsense? thank you very much...

  Read the article

• Using 2 Transparent HAProxy for load balancing

  - by Nyxynyx

  We can configure HAProxy to be a transparent proxy by using the guide here, where one of the steps says ...to put the backend servers in a different subnet to the front end clients and make sure that the default gateway points back at the HAProxy load balancer. However when we need to have 2 transparent HAProxy in front of our balanced servers (for redundancy), it seems like this wont work as we can only set one gateway for our balanced servers. What will be the correct way to setup the system such that we can have 2 transparent HAProxy infront of the balanced servers? The main reason for having transparent proxies is the need to find the client's IP addresses over TCP.

  Read the article

< Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >