Search Results

Search found 10810 results on 433 pages for 'port forwarding'.

Page 301/433 | < Previous Page | 297 298 299 300 301 302 303 304 305 306 307 308  | Next Page >

• Cisco 1760 T1 Setup

  - by Joseph

  My 1760 has a WIC1-T1 card in Slot 0 and the slot 0 "OK" light is lit. When the router boots it shows that it sees the T1 card. I would like to configure my T1. I received the following details from my ISP: * Removed IP's IP Version: IPv4 Router Interface: edge1.mia1 -- t1-2/1/0:2:13 -- Switch Port: Vlan: WAN Network: 4.59.?.?/30 Level3 Side: 4.59.?.? Customer Side: 4.59.?.? Cust. LAN IPs: 4.59.?.?/27 The problem is that it is not listed under interfaces. I am a noob with IOS, please let me know if you need more details. Thanks.

  Read the article

• Yum through http proxy

  - by eodchop

  I have several Fedora 13 servers that have to connect through an http proxy for yum updates. All port 80 traffic has to be routed through this proxy. I have setup the proxy server in the network settings GUI. I can browse the internet just fine. I have also setup my proxy information in /etc/yum.conf as follows: proxy=http:proxy.largecorp.corp/accelerated_pac_base.pac proxy_user=user proxy_password=password I then added the export HTTP_PROXY="http:proxy.largecorp.corp/accelerated_pac_base.pac" to /etc/bashrc and sourced the file. When i run yum update: Loaded plugins:presto, refresh-packagekit Error: Cannot retrieve repository metadata (repomd.xml) fro repository: fedora. Please verify its path and try again. All of the repo urls are the defaults, as this is a fresh install.

  Read the article

• Postfix cleanup daemon access control

  - by Flimzy

  Is there any way to control which hosts are permitted to connect to the cleanup daemon over TCP? Our 'master.cf' contains: 2526 inet n - - - 0 cleanup This is necessary because we have a cluster of SMTP servers running custom code, and they can all inject mail to the centralized postfix server via the cleanup daemon. However, we want to allow only our authorized servers to connect to the cleanup daemon. The current configuration allows any host to connect to port 2526. Clearly we can use iptables to restrict access, but is there a way to do this within postfix itself?

  Read the article

• Connecting via url to a server that is on the same network as me

  - by Axehead

  Good day, I'm having problems with the ftp server I've just set up. I've already managed to configure my modem and wireless router to open up port 21 and setup ftp in my server. But It seems that when I try to connect to it when I'm in the same network as the server via URL, (ftp://mydomain.com) it redirects me to the modem's web interface. But then when I try to connect to it outside the network using a different internet connection. It succeeds. It also succeeds when I'm in the same network and I go to ftp://192.168.., the server's local IP. Am I supposed to adjust something in the modem or router? Or is this a different problem altogether? BTW I'm using Windows Server 2008 r2 as my server's OS and using IIS for ftp.

  Read the article

• Can Camel Jetty proxy URL share the webapplication context

  - by user1750353

  I am struggling with Camel Jetty Proxy Routes. At times, the routes exhibits inconsistent behavior. My Proxy app deployed with context root "Proxy", however, if give that as the context path for my proxy URL I get service not found error. If change the Proxy to an arbitrary context such as "Dummy" then the route works. Is that how camel jetty component works? From Path: jetty:http://0.0.0.0:6080/Proxy/PurchaseOrder/?matchOnUriPrefix=true&disableStreamCache=true&traceEnabled=true To Path: jetty:http://localhost:7001/Provider/PurchaseOrder/?bridgeEndpoint=true&throwExceptionOnFailure=false Another issue i noticed with jetty is If deploy both Proxy and Provider on the same app container(same listening port), then the route completely stops working saying "Provider/PurchaseOrder/" service not found. The only way the routes work is, both routes have to run different ports and the from route shouldn't share the webcontext path. I have requirement that if required I should be a able run both Proxy and Provider on the same container. Any help appreciated. Thanks,

  Read the article

• How can I monitor network traffic in an all Mac home network?

  - by raiglstorfer

  I have an all Mac network consisting of an Airport Extreme, 1 MacPro, 1 Mac Mini, 2 MackBook Pros, 2 iPads, and 2 iPhones. The Mac Pro is connected directly to the Airport Extreme via Cat5 and the rest is all running via Wireless. Lately I've been getting prompted by Google to enter Capchas frequently. The message states that I might have software running on my network I'm not aware of. My wireless router is password protected using WPA2 Personal and I frequently change my password so I don't think someone is using the network from outside (but I've no way to confirm this). I'm looking for a relatively cheap (preferably open source) solution that would enable me to monitor and profile the network usage by machine and port. Can someone recommend a solution?

  Read the article

• Can't connect to server from certain machines

  - by Joel Coel

  On a small college campus we have a VLAN setup for the computer labs. These machines get assigned IP addresses in the 192.168.7.xxx range. In the server room, all of the server are on the default VLAN and assigned an IP address in the 10.1.1.xxx range. For the most part this works, but the lab machines are unable to connect to one of the servers. They can't even ping it. They can talk to other servers on the same switch as this server just fine. At first I thought it might be a vlan issue, but I changed the server port vlan to match other known-working ports with no effect. Any ideas?

  Read the article

• How can I monitor network traffic in an all Mac home network?

  - by raiglstorfer

  I have an all Mac network consisting of an Airport Extreme, 1 MacPro, 1 Mac Mini, 2 MackBook Pros, 2 iPads, and 2 iPhones. The Mac Pro is connected directly to the Airport Extreme via Cat5 and the rest is all running via Wireless. Lately I've been getting prompted by Google to enter Capchas frequently. The message states that I might have software running on my network I'm not aware of. My wireless router is password protected using WPA2 Personal and I frequently change my password so I don't think someone is using the network from outside (but I've no way to confirm this). I'm looking for a relatively cheap (preferably open source) solution that would enable me to monitor and profile the network usage by machine and port. Can someone recommend a solution?

  Read the article

• Combine VPN bandwith over two or more WAN connections? Load balancing?

  - by mistrfu

  Imagine you only have DSL with 5mbps Down and 2mbps Up. Is it possible to have 10 of these for example and combine them in a way that would increase the upstrean bandwidth to one server? In my head it works like this: intranet with one gateway/router router connected to multi wan load ballancer on each ballancer wan port router with vpn clinet set up, tunneling to a server ?some? software on the server in cloud joining all these connection into one interface again I would need this mostly for big uploads to a server, downlink to the office is not that important at all. Does it even make sense? I drew an image to clarify.

  Read the article

• VLC stream with trickplay

  - by marjasin

  The idea is to start a video stream from one computer and watch it on another with the ability to start/stop the stream. I think I could do this with VLC but i haven't been able to figure out how. I've tried the following: (From the official forum) Stream with RTSP and RTP: on the server, run: % vlc -vvv input_stream --sout '#rtp{dst=192.168.0.12,port=1234,sdp=rtsp://server.example.org:8080/test.sdp}' on the client(s), run: % vlc rtsp://server.example.org:8080/test.sdp But this doesn't give me the ability to start/stop the stream from the client. According to the VLC release note something called "Trick play" was added in version 1.0. This seems to be what I'm looking for but i can't find any documentation that descibes how to use it.

  Read the article

• How to configure my web server for public and development service

  - by Steve

  I have one and only one web server, which runs Windows Server 2008 and wamp. Now I would like to setup SVN on the server so I can program the trunk version of the website. Every time I branch a version and put it to public. While developing on the trunk version, I also want to be able to test it. The web server has 5 IPs so I can use one IP for public website(the branch) and another IP for trunk development test. I believe one wamp server can only handle one 80 port request thus can only handle one website. How can I configure the server so it can handle one IP request and direct to my branch and handle another IP request and direct to my trunk?

  Read the article

• All HTTPS, or is it OK to accept HTTP and redirect (secure vs. user friendly)

  - by tharrison

  Our site currently redirects requests sent to http://example.com to https://example.com -- everything beyond this is served over SSL. For now, the redirect is done with an Apache rewrite rule. Our site is dealing with money, however, so security is pretty important. Does allowing HTTP in this way pose any greater security risk than just not opening or listening on port 80? Ideally, it's a little more user-friendly to redirect. (I am aware that SSL is only one of a large set of security considerations, so please make the generous assumption that we have done at least a "very good" job of covering various security bases.)

  Read the article

• APC UPS-5000 Power off remote servers

  - by Vishal

  Hi there, I have a UPS connected via the serial port to a server using PowerChute Business Edition. If a power outage occurs I would like this server to start shutting down all other servers within the network. Is there dedicated software to do this? I was thinking of creating a command file which runs a .bat file to run shut down commands to each server (using PSExec). I can set PowerChute to run this command file when a power failure occurs. Is there not anything APC provide which has this functionality and is more efficient than writing a .bat file to do this? Thanks,

  Read the article

• How to make all of my IPs works in HyperVM XEN?

  - by user758667

  I've installed HyperVM on CentOS 5.8 final to make XEN VPS. I have 5 IPs, and added them to an IPPool. They are from *.123 to *.126. But when I add Virtual machines, just the first one (which indicate to *.123 ip) works well. I mean I can ssh to it by "works well" and when I want ssh to the other ones ( *.124 *.125 ...) it says : ssh: connect to host *.124 port 22: Connection timed out after a while. I alos set gateway and netmask as it shows in my server IPAdresses for device eth0 (it doesn't make any difference if I set these or not, I get same error). What should I do now? Thanks.

  Read the article

• IIS7 houndreds of connections in CLOSE_WAIT

  - by rjlopes

  I have a .Net application on my IIS7 server it was working fine until I had to move it to another server. I moved the exact same code to the new server and I noticed that after some hours the website stopped responding to remote requests but if I did remote desktop to the server it responded to the request done to localhost. If I stop the website and the application pool it started working fine again. I was able to track the problem to hundreds of requests left in CLOSE_WAIT state to the http port that are never closed (I waited a few hours and they remain the same). Any ideias?

  Read the article

• Connect to my virtualbox mysql server

  - by WebweaverD

  I wonder if someone here could help me, this is my set up: I am on a windows 7 machine running a ubuntu virtualbox as my local web server and database server (mysql). I have just got hold of a copy of Komodo which i am running on my windows machine which I would like to hook up to my database. The fields it needs are hostname, port, socket, username and password. I know the username/password but am unsure how to find out what to put for the other fields. The ubuntu vb has an ip of 192.168.0.10, which is in my hosts file as http://swishprint.dev I hope I have asked this in the right place, any help much appreciated.

  Read the article

• elastix cdr stop working

  - by dreddko

  CDR was working before 19 march. Unfortunately i dont remember what kind of changes i made to configuration, but this exactly not changes to CDR config. elastix 2.4.0 asterisk 11.7.0 mysql 5.0.95 elastix*CLI> cdr show status Call Detail Record (CDR) settings ---------------------------------- Logging: Disabled Mode: Simple /etc/asterisk/cdr.conf [general] enable=yes unanswered = yes /etc/asterisk/cdr_mysql.conf [global] hostname = localhost dbname=asteriskcdrdb password = *MYPASSWROD* user = asteriskcdruser userfield=1 ;port=3306 ;sock=/tmp/mysql.sock loguniqueid=yes mysql> SHOW GRANTS FOR 'asteriskcdruser'@'localhost'; +-----------------------------------------------------------------------------------------------+ | Grants for asteriskcdruser@localhost | +-----------------------------------------------------------------------------------------------+ | GRANT USAGE ON *.* TO 'asteriskcdruser'@'localhost' IDENTIFIED BY PASSWORD 'HASHHERE' | | GRANT ALL PRIVILEGES ON `asteriskcdrdb`.* TO 'asteriskcdruser'@'localhost' | +-----------------------------------------------------------------------------------------------+ 2 rows in set (0.00 sec)

  Read the article

• Wi-Fi or Bluetooth to USB converter

  - by yerzhik

  Is there a device, that works without a driver, you just connect it as usb, and receive any signal sent to it as if it were COM Port wired connection? For example, such a device that gets data sent to it by Wi-Fi network or Bluetooth and resends it to the USB. Of course it has to be set up once (network name, password etc) and for this purpose you need a driver, but once it is set up, you can use it at any computer without a driver. I have a Bluetooth USB, but I think it can't work without a driver. By just connecting it to any computer you can't find it in device list on another bluetooth device (as phone, etc).

  Read the article

• Time Capsule + Ubee Router?

  - by Charlie

  I can't for the life of me figure this out. I recently had TWC installed in my house, and wanted to disable the NAT and router functions of it. I have a Time Capsule hooked up to it from LAN1 (on the Ubee) to the WAN port on the TC. The problems started occurring here. I figured the settings would be these: Ubee Configuration mode: Bridge DHCP: Off TC IPv4: 192.168.100.2 Subnet Mask: 255.255.255.0 Router Address: 192.168.100.1 DNS Servers: 8.8.8.8, 8.8.4.4 Router Mode: DHCP and NAT But using those settings, my TC says "Double NAT", so I have to change it all around to the default settings of the Ubee using NAT. This leads me to believe bridge mode doesn't actually turn off NAT...

  Read the article

• domain/IN: has no NS records

  - by thejartender

  I have set up a home web server using Ubuntu 12.10 and I can safely say that it works with regards to router forwarding and ports being found. I know this, because switched my hosting provider's VPS SOA record to use my ISP IP with an 'A' value and had my website running from home. This verified that my server was configured correctly so I started what I believe to be the final step in making my old desktop into a full DNS server. I found this tutorial that got me started My LAN network consists of the following: My router with a gateway of 10.0.0.zzz My server with an IP of 10.0.0.xxx A laptop with an IP of 10.0.0.yyy Step 1: I installed bind via sudo apt-get install bind9 Step2: I configured /etc/bind/named.conf.local with: zone "sognwebdesign.no" { type master; file "/etc/bind/zones/sognwebdesign.no.db"; }; zone "0.0.10.in-addr.arpa" { type master; file "/etc/bind/zones/rev.0.0.10.in-addr.arpa"; }; Step3: Updated /etc/bind/named.conf.options with two ISP DNS addresses Step 4: Updated /etc/resolv.confwith: nameserver 10.0.0.xxx search lan search sognwebdesign.no Step5: created a ``/etc/bind/zones directory Step6: Created /etc/bind/zones/sognwebdesign.no.dbwith: $TTL 3D @ IN SOA ns.sognwebdesign.no. admin.sognwebdesign.no. ( 2007062001 28800 3600 604800 38400 ); sognwebdesign.no. IN NS ns1.sognwebdesign.no. sognwebdesign.no. IN NS ns2.sognwebdesign.no. sognwebdesign.no. IN NS ns3.sognwebdesign.no. NS1 IN A 10.0.0.1 NS2 IN A 10.0.0.2 NS3 IN A 10.0.0.3 www IN A 10.0.0.4 yuccalaptop IN A 10.0.0.19 gw IN A 10.0.0.138 TXT "Network Gateway" Step 7: created/etc/bind/zones/rev.0.0.10.in-addr.arpawith: $TTL 3D @ IN SOA ns.sognwebdesign.no. admin.sognwebdesign.no. ( 2007062001 28800 604800 604800 86400 ); zzz IN PTR gw.sognwebdesign.no. 1 IN PTR ns1.sognwebdesign.no. 2 IN PTR ns2.sognwebdesign.no. 3 IN PTR ns3.sognwebdesign.no. yyy IN PTR yuccalaptop.sognwebdesign.no. I then restart bind and dig-x sognwebdesign.no and it works Lastly I perform named-checkzoneon each of my zone files, but me reverse zone fail fails with: sognwedesign.no/IN: has no NS records Can anyone explain what I am doing wrong here or assist me in getting this configured correctly?

  Read the article

• Accessing to shared folders with OpenVPN

  - by Ergec

  This is my first attempt to configure a vpn so I have very little knowledge about this. Network where centos server is having local IPs 192.168.123.* Network where windows machine is having local IPs 192.168.1.* I installed and configured my openpvn server on centos 5 and client on a windows machine. Generated all keys, certificates e.t.c and transferred them to client and I'm able to connect to server. Below there is a screenshot of the client log. Also on server side I can also see incoming packets with this command tcpdump -n port 1723 So I assume I did most of the things correct. But still when I try to open shared folders using \\192.168.123.33 or \\network-name I can't access folders

  Read the article

• Apache Conf files: If Hostname=="Web4" Then Use This IP for VirtualHost

  - by jroberts

  I am getting ready to do a "spring cleaning" on the web heads at work. I would really like to put my config files into a git repo, and use the same config files for all the web heads. This is a problem for the sites that are on port 443. Is there anyway to do an if statement or something like that inside the conf file itself? I am trying to avoid writing a script to generate the conf files. Any ideas are greatly appreciated!! Thank you! Jeff

  Read the article

• Stopped windows firewall service during ICS, how is this possible?

  - by insipid

  Although windows firewall is required to be on when you "start" Internet Connection Sharing, you can stop the WF service with MMC. When done a client can still use the host machines internet. The firewall had port 80/http blocked, and now it is open for incoming traffic. However other ports used by applications on the host and client which communicate with each other still seem to be blocked. Can anybody explain what might be happening here? Doesn't ICS need windows firewall for NAT? Note: I am not actually seeing anything in the firewall logs after stopping the service, but even packets sent localhost on the host machine never arriving on these other random ports.

  Read the article

• Where can I connect this USB 3.0 cord?

  - by tomsawyer95

  My motherboard has 2 USB 3.o slots in the back, where the usual slots go, but the tower also supports 1 or 2 USB 3.0 ports in the front, above the DVD drive. So, there is a cord coming out of those ports that has an end exactly like the one in the attached picture. I am not able to find a matching port on the mobo, so I presume it doesn't have one, and I would need an adapter or else just leave it inoperable. I have an ASUS P8Z68-V LX and an Antec 900 tower.

  Read the article

• When should I use SATA 6gb/s?

  - by Gili

  I purchased a Baraccuda hard-drive (model ST3000DM001) that supports a maximum read transfer rate of 210 MB/s and SATA 1.5/3/6 Gb/s. My motherboard has a limited number of 6 Gb/s ports so I'd like to reserve them for when it's really necessary. When does a hard-drive benefit from a SATA 6 Gb/s port? Doesn't it require a transfer speed of at least 375 MB/s to surpass the limit of SATA 3 Gb/s? Are there any other benefits of SATA 6 Gb/s vs 3 Gb/s ports?

  Read the article

< Previous Page | 297 298 299 300 301 302 303 304 305 306 307 308  | Next Page >