Search Results

Search found 22267 results on 891 pages for 'org mode'.

Page 304/891 | < Previous Page | 300 301 302 303 304 305 306 307 308 309 310 311  | Next Page >

• Windows XP corrupts registry every several hours

  - by Ilya Kazakevich

  There is a Dell XPS 400 with Windows Media Center installer. It is installed on RAID (Intel Matrix Storage) which is built-in chipset south bridge. Raid has two 150 Gb WDC drivers connected as mirror. All drivers and updates are installed( sp3 and so on). A week ago PC changed its video mode to 256 colors (like VESA mode) and after several moments I got BSOD: c000021a: 0xc0000005 Doctor watson did not create dump although it is installed as default debugger. After reboot it said that config file is missing or corrupted. So, I boot to recovery console and found that registry file (config) is so small. I've replaced it with one from recovery point and windows booted sucessfully. But after about 3 hrs -- it has crashed again in the same wat! I look in event viewer: is said that Explorer.exe failed to open \global??\DLIAFS. I look in winobj, and found that it is a device. I made "deny from everyone" for this device ACL, and after several hours my windows crashed. I restored registry, boot again and there was no error about DLIAFS. I did full chkdsk and it did not found anything bad. But I found event about error paging to \Harddrive1\D. I do not have pagefile there, but I thought I should check my disk again. Unfortunatelly I cannt use smart tools for RAID, but I downloaded latest software from Intel (it can do the same things like RAID bios can but from windows). It verified my disks, found some errors, fix them, than I rebooted. And it crashed again. I am lost. What (except kernel debugging) could be done here? Thanks

  Read the article

• Windows XP corrupts registry every several hours

  - by Ilya Kazakevich

  There is a Dell XPS 400 with Windows Media Center installer. It is installed on RAID (Intel Matrix Storage) which is built-in chipset south bridge. Raid has two 150 Gb WDC drivers connected as mirror. All drivers and updates are installed( sp3 and so on). A week ago PC changed its video mode to 256 colors (like VESA mode) and after several moments I got BSOD: c000021a: 0xc0000005 Doctor watson did not create dump although it is installed as default debugger. After reboot it said that config file is missing or corrupted. So, I boot to recovery console and found that registry file (config) is so small. I've replaced it with one from recovery point and windows booted sucessfully. But after about 3 hrs -- it has crashed again in the same wat! I look in event viewer: is said that Explorer.exe failed to open \global??\DLIAFS. I look in winobj, and found that it is a device. I made "deny from everyone" for this device ACL, and after several hours my windows crashed. I restored registry, boot again and there was no error about DLIAFS. I did full chkdsk and it did not found anything bad. But I found event about error paging to \Harddrive1\D. I do not have pagefile there, but I thought I should check my disk again. Unfortunatelly I cannt use smart tools for RAID, but I downloaded latest software from Intel (it can do the same things like RAID bios can but from windows). It verified my disks, found some errors, fix them, than I rebooted. And it crashed again. I am lost. What (except kernel debugging) could be done here? Thanks

  Read the article

• Connecting a network printer via a Thecus N2100 - works in Vista, not in Windows 7

  - by Jon Skeet

  I have a Lexmark E250d printer attached to a Thecus N2100 NAS. On Windows Vista I've managed to configure this using an "Internet" printer port with the URL of http://thecus:631/printers/usb-printer. I can add a printer in a similar way in Windows 7, but it never manages to print the test page. If I go to "Configure Port" in Vista, it just has "Security Options" - on Windows 7 it's asking about Raw mode vs LPR mode etc. On Vista I'm using an E250d-specific driver from Lexmark; on Windows 7 there's a Microsoft E250d driver, or a Universal PCL XL driver from Lexmark... I wouldn't expect this different to be related to the problem, but I thought I'd mention it anyway. (Lexmark doesn't have a Windows 7 E250d-specific driver as far as I can see.) Any suggestions? I was thinking of upgrading my main laptop from Vista to Windows 7, but I'd really like to get this sorted first... EDIT: If I connect to http://thecus:631/printers/usb-printer via Chrome while capturing with Wireshark, I get this response: HTTP/1.1 200 OK Date: Wed, 06 Jan 2010 16:47:23 GMT Connection: Keep-Alive Keep-Alive: timeout=60 Content-Language: C Transfer-Encoding: chunked Content-Type: text/html;charset=iso-8859-1 0 No idea what that's meant to be doing... EDIT: On further consultation, this would appear to be the Internet Printing Protocol which is layered on HTTP. Printing a test page successfully from Vista posts to that URL. Will attempt the same on Windows 7...

  Read the article

• Appears to be "randomly" switching between the acl matched backend and the default backend

  - by Xoor

  I have HAProxy acting as a proxy in front of: An NGinx instance An in-house load balancer in front of multiple dynamic services exposed with socket.io (websockets) My problem is that from time to time my connections are proxied correctly to my socket.io cluster, and then randomly it fallsback to routing to NGinx which obviously is annoying and meaningless since NGinx isn't mean't to handle the request. This happens when requesting for URLs of the format : http://mydomain.com/backends/* There's an ACL in the HAProxy config to match the '/backends/*' path. Here's a simplified version of my HAProxy config (removed extra unrelated entries and changed names): global daemon maxconn 4096 user haproxy group haproxy nbproc 4 defaults mode http timeout server 86400000 timeout connect 5000 log global #this frontend interface receives the incoming http requests frontend http-in mode http #process all requests made on port 80 bind *:80 #set a large timeout for websockets timeout client 86400000 # Default Backend default_backend www_backend # Loadfire (socket cluster) acl is_loadfire_backends path_beg /backends use_backend loadfire_backend if is_loadfire_backends # NGinx backend backend www_backend server www_nginx localhost:12346 maxconn 1024 # Loadfire backend backend loadfire_backend option forwardfor # This sets X-Forwarded-For option httpclose server loadfire localhost:7101 maxconn 2048 It's really quite confusing for me why the behaviour appears to be "random", since being hard to reproduce it's hard to debug. I appreciate any insight on this.

  Read the article

• Windows Service with Logon a user

  - by David.Chu.ca

  I have a service running in a box with Windows XP and a box of Server (2003). There is one service running in autmactic mode. If I set the log on with a local user, the service will stop running if the user logs off the account from the Windows? In other words, in order to keep the service running, have I to keep the user as login mode? I understand that the service can be set as local system which will not need any one to login as long as the box is powered on. However, the service I need to run has to be running as a local user with the required permissions. The problem I have right now is that the box may reboot itself. If that happens, no one is logged in yet until some one has to log in as the required user. I want to make sure if the required user has to be as a log on user first. If that's the case, any suggestion to deal with unexpected reboot issue?

  Read the article

• Migrateing to Windows Server 2008 R2 Domain Controllers - a few Questions/Issues

  - by Chris

  Ok so here's our setup: We have 2 Windows2k3 Domain Controllers. I am trying to replace them with Windows 2008 R2. The Win2k3 servers are DC01 and DC02. The Windows2k8 servers are DC1 and DC2. I prepared the Windows Server 2003 Forest Schema for a Domain Controller That Runs Windows Server 2008 or Windows Server 2008 R2. Then with both of the new servers up as member servers I dcpromo'd DC1 using the advanced option and added it successfully to my exisiting domain. Roles are GC, DNS and Active Directory Domain Services.I transferred The PDC, RID pool manager and Infrastructure master FSMO to the new DC.(DC1) The Schema master and Domain naming master are still on the old DC (DC01). The first issue I'm encountering is when i dcpromo the second DC (DC2) and select "Replicate data over the network from and existing domain controller" I select the new DC to replicate from (DC1) I get the following error: "Failed to identify the requested replica partner (dc1.xxx.org) as a valid domain controller with a machine account for (DC2$). This is likely due to either the machine account not being replicated to this domain controller because of replication latency or the domain controller not advertising the Active Directory Domain Services. Please consider retrying the operation with \dc01.xxx.org as the replica partner. "The server is unwilling to process the request." Is this because the Schema master and Domain naming master roles are still on the old DC (DC01)? And if so, if I transfer Schema master and Domain naming master roles to DC1 what is the risk or breaking my AD? I'm a little paranoid because this process HAS to be transparent. ANY down time or interruption will result in me getting a verbal ass kicking from my I.T. Director. Both of the new servers DNS point the the old DNS servers (DC01 and DC02) not themselves by the way. Thanks in Advance -Chris

  Read the article

• How do hdparm's -S and -B options interact?

  - by user697683

  These two options seem confusing. For example: according to the man page -B 254 "does not permit spin-down". However, testing with -B 254 -S 1 the drive does spin down after 5 seconds. -B Query/set Advanced Power Management feature, if the drive supports it. A low value means aggressive power management and a high value means better performance. Possible settings range from values 1 through 127 (which permit spin-down), and values 128 through 254 (which do not permit spin-down). The highest degree of power management is attained with a setting of 1, and the highest I/O performance with a setting of 254. A value of 255 tells hdparm to disable Advanced Power Management altogether on the drive (not all drives support disabling it, but most do). -S Put the drive into idle (low-power) mode, and also set the standby (spindown) timeout for the drive. This timeout value is used by the drive to determine how long to wait (with no disk activity) before turning off the spindle motor to save power. Under such circumstances, the drive may take as long as 30 seconds to respond to a subsequent disk access, though most drives are much quicker. The encoding of the timeout value is somewhat peculiar. A value of zero means "timeouts are disabled": the device will not automatically enter standby mode. Values from 1 to 240 specify multiples of 5 seconds, yielding timeouts from 5 seconds to 20 minutes. Values from 241 to 251 specify from 1 to 11 units of 30 minutes, yielding timeouts from 30 minutes to 5.5 hours. A value of 252 signifies a timeout of 21 minutes. A value of 253 sets a vendor-defined timeout period between 8 and 12 hours, and the value 254 is reserved. 255 is interpreted as 21 minutes plus 15 seconds. Note that some older drives may have very different interpretations of these values.

  Read the article

• Installing WinPcap on Windows 8

  - by Dave Robinson

  I know there has been lots of discussion already on installing WinPcap on Windows 8. I'm running the RTM version. I was able to install WinPcap without a hitch by using the Windows 7 compatibility mode. Since then, I've noticed that WinPcap has stopped running and is actually no longer even installed. I tried installing it again, but now it continues to tell me that WinPcap does not work with my version of Windows. Compatibility modes and admin privileges make no difference. The only thing I remember doing to my system was installed 900MBs of Windows Updates. Does anyone have any ideas about what I might do to get WinPcap installed? I've already ensured that the compatibility mode settings I changed were in effect for all users. I've already ensured that "run this program as an administrator" is checked on the compatibility tab for all users. I've also tried installing WinPcap 4.1.2 and 4.1.1. No success with either.

  Read the article

• Java web app deployment and ControlTier adoption

  - by Ran

  I've been searching for a configuration and deployment manager tool for my java-linux based web service and have been looking mainly at ControlTier (http://controltier.org). We operate at a medium scale (100's of hosts, multi-DC, dozens of services). There seem to be be plenty of lower level system admin tools such as chef, puppet, cfengine, bcfg2 and more and my understanding and the reason I'm calling them "low level" is that they are great for system level administration tasks such as setting up a mount, file permissions, users etc but aren't designed, for example for java deployments, which usually come with a build process and special java semantics. In many cases any tool can be used to do anything but if it was not designed for the task it can get uncomfortable. OTOH control-tier seem to have been designed just for that - java application deployments, at least that's what all the tutorials on their site demonstrate but here's the problem - The wiki at http://controltier.org/wiki/ is pretty good and stuffed with examples and the company behind the open source CT product is very responsive (pushy...) however, I'm yet to have seen any material from 3rd party users on the net. No success stories, no detailed blog posts, no best practices, no cheat sheets, not even hate letters, nothing. This plays badly for DTO solutions, CT's sponsor for two reasons, one is that it makes me suspicious what's the reason for the poor adoption? and second, what do I do if I get stuck and there's no help page on CT's wiki page and the mailing list is too slow to answer. I'm stuck with a "free" product that a consultancy company is pushing. So my question here - I'd be interested in hearing if anyone has had real world experience with CT for java based web app deployments and if he'd thumb up the product? Any other comments that may enlighten me are welcome of course...

  Read the article

• How do I hook into Tar with BASH?

  - by orb

  Long Story Short I am working with Tar archives that contain PNG images in base64 encoding. I would like to use BASH (or whatever else works) to hook into the extraction function of Tar to decode PNG images from base64 encoding to standard PNG encoding after the files are unpacked. A simple cat $input-file | base64 -d >$output-file will successfully decode the images. Is there a way I can hook into tar -xf so that users do not have to do any (or minimal) extra work to decode the images? In the GNU Tar documentation (http://www.gnu.org/software/tar/manual/html_chapter/Backups.html#SEC97) I found that there are in fact variables reserved to hold the names of functions I desire to be hooked into various moments in Tar program execution. However, the documentation explains that these variables, along with other variables that can be set to configure Tar, are located in a file named backup-specs. Unfortunately, the path to this file is not given. Further, running sudo find / -name backup-specs tells me that this file is not present on my Ubuntu version 13.04 system. Background Information not included in the Long Story Short I have been working on a browser-based (WebGL) particle effect creation application (http://www.particleeffect.org), (https://github.com/cgrabowski/webgl-particle-effect-editor), (https://github.com/cgrabowski/webgl-particle-effect). I have began to write a client-side-only solution for saving and loading effect data as a tar archive. However, since client-side JavaScript has limited capability to process binary data, the images used as textures in the effect are saved with base64 encoding. I have been able to implement saving effect data as a Tar archive (haven't pushed that to Github yet). However, the images present in said Tar archive cannot be manipulated unless they are decoded from base64 encoding.

  Read the article

• .htaccess rewrite rule to ignore a directory

  - by Kirk Strobeck

  I am running a Symphony installation out of the directory symphony but I want to remove that word from the URL in specific cases. When a user visits http://domain.com/demo It should go to http://domain.com/symphony/demo because I've added a specific rule for demo. If I haven't added a specific rule for demo in the .htaccess, then it should resolve to http://domain.com/demo as typed. This will route it to another part of our app. Here is my current rewrite rule ### Symphony 2.3.x ### Options +FollowSymlinks -Indexes <IfModule mod_rewrite.c> RewriteEngine on RewriteBase / ### SECURITY - Protect crucial files RewriteRule ^manifest/(.*)$ - [F] RewriteRule ^workspace/(pages|utilities)/(.*)\.xsl$ - [F] RewriteRule ^(.*)\.sql$ - [F] RewriteRule (^|/)\. - [F] ### DO NOT APPLY RULES WHEN REQUESTING "favicon.ico" RewriteCond %{REQUEST_FILENAME} favicon.ico [NC] RewriteRule .* - [S=14] ### IMAGE RULES RewriteRule ^image\/(.+\.(jpg|gif|jpeg|png|bmp))$ extensions/jit_image_manipulation/lib/image.php?param=$1 [B,L,NC] ### CHECK FOR TRAILING SLASH - Will ignore files RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_URI} !/$ RewriteCond %{REQUEST_URI} !(.*)/$ RewriteRule ^(.*)$ $1/ [L,R=301] ### URL Correction RewriteRule ^(symphony/)?index.php(/.*/?) $1$2 [NC] ### ADMIN REWRITE RewriteRule ^symphony\/?$ index.php?mode=administration&%{QUERY_STRING} [NC,L] RewriteCond %{REQUEST_FILENAME} !-d RewriteCond %{REQUEST_FILENAME} !-f RewriteRule ^symphony(\/(.*\/?))?$ index.php?symphony-page=$1&mode=administration&%{QUERY_STRING} [NC,L] ### FRONTEND REWRITE - Will ignore files and folders RewriteCond %{REQUEST_FILENAME} !-d RewriteCond %{REQUEST_FILENAME} !-f RewriteRule ^(.*\/?)$ index.php?symphony-page=$1&%{QUERY_STRING} [L] </IfModule> ###### How would I change the rewrite rule to support those cases?

  Read the article

• Mac creating files w/ wrong perms on samba share

  - by geoffjentry

  In my group, which is very heterogeneous in terms of machines, we use a samba share to collaborate on files and such. In all but one case, it works as expected (or at least close enough). The one exception is my boss' laptop, a snow leopard macbook air. On his desktop (also snow leopard), if he creates a file it ends up serverside with perms of 774, but when he creates it with the Air, the perms are 644. The key problem is the lack of group write permission on the laptop created files. What's really confusing is that everything that I've looked at on the two machines are identical - same version of OS X, same version of samba (3.0.25b-apple), same settings for the same software, etc. I can't imagine why one machine would be different than the other, but it is. To try to be complete w/ the description, here is the relevant portion of my smb.conf file: comment = my Share path = /path/to/share public = no writeable = yes printable = no force group = myshare directory mask = 0770 create mask = 0770 force create mode = 0770 force directory mode = 0770 EDIT: I looked at three more Macs and all of them worked as expected which leaves this one laptop the true oddball. This wasn't as good as a test as the others though, as they were all leopard.

  Read the article

• Shrink a Volume Group in LVM / Linux in order to install Windows on the freed space

  - by Stephan Kristyn

  I have a Volume Group with Unused space. This 40Gig should become an entidy in order to install Microsoft windows 7 on it. I do not have extra space on the drive - that is why I want to shrink the VG! LVG berta resides on sda2 and consists of lv_root lv_swap unused_space I want it to become lv_root lv_swap and have a seperate entidy made out of unused_space. Microsoft Windows 7 has to get installed on this entidy. I do not understand why Linux made simple things complicated. I utterly hate LVM and think its absolute bollocks. Useful Sources: http://www.centos.org/docs/5/html/Deployment_Guide-en-US/s1-system-config-lvm.html Edit: I found the answer. The necessary steps depict how complicated LVM really is. In my opinion it is best to avoiding LVM until pvresize matures as promised in its man pages. Answer: http://fedorasolved.org/Members/zcat/shrink-lvm-for-new-partition If you run into problems when you want to remove lvswap even if in resuce mode, then try swapoff /dev/vg_1/lv_swap lvchange -an /dev/vg_1/lv_swap

  Read the article

• (13) Permission denied on Apache CGI attempt

  - by ncv

  I have recently upgraded my Apache2 server, and am now unable to run a CGI app. My logs are showing (13) Permission denied unable to connect to cgi deamon after multiple tries I understand that the error message means Apache is being denied some permission to some file, and I'm stumped as to how to track down and solve the problem. Is the file mentioned in the error message truly the blocked file? Or might the problem be caused by some other needed file? The .cgi file is right where it has always been, under /usr/share. The file ownership (root) and permissions (world readable/executable) are the same as they have always been for the file and its ancestors. The SELinux file labels are unchanged. The SELinux audit log shows no denial associated with Apache nor the CGI program. In case of a donotaudit condition, I enabled audit, but still saw nothing. I switched SELinux into permissive mode briefly, to no avail. I even tried restarting Apache while in permissive mode. This did not solve the problem. Any suggestions on how to solve this problem? I'm tempted to just revert to the older Apache.

  Read the article

• Easy_install the wrong version of python modules (Mac OS)

  - by user73250

  I installed Python 2.7 on my Mac. When typing "python" in terminal, it shows: $ python Python 2.7 (r27:82508, Jul 3 2010, 20:17:05) [GCC 4.0.1 (Apple Inc. build 5493)] on darwin Type "help", "copyright", "credits" or "license" for more information. The Python version is correct here. But when I try to easy_install some modules. The system will install the modules with python version 2.6 which are not able be imported to Python 2.7. And of course I can not do the functions I need in my code. Here's an example of easy_install graphy: $ easy_install graphy Searching for graphy Reading pypi.python.org/simple/graphy/ Reading http://code.Google.com/p/graphy/ Best match: Graphy 1.0.0 Downloading http://pypi.python.org/packages/source/G/Graphy/Graphy- 1.0.0.tar.gz#md5=390b4f9194d81d0590abac90c8b717e0 Processing Graphy-1.0.0.tar.gz Running Graphy-1.0.0/setup.py -q bdist_egg --dist-dir /var/folders/fH/fHwdy4WtHZOBytkg1nOv9E+++TI/-Tmp-/easy_install-cFL53r/Graphy-1.0.0/egg-dist-tmp-YtDCZU warning: no files found matching '*.tmpl' under directory 'graphy' warning: no files found matching '*.txt' under directory 'graphy' warning: no files found matching '*.h' under directory 'graphy' warning: no previously-included files matching '*.pyc' found under directory '.' warning: no previously-included files matching '*~' found under directory '.' warning: no previously-included files matching '*.aux' found under directory '.' zip_safe flag not set; analyzing archive contents... graphy.all_tests: module references __file__ Adding Graphy 1.0.0 to easy-install.pth file Installed /Library/Python/2.6/site-packages/Graphy-1.0.0-py2.6.egg Processing dependencies for graphy Finished processing dependencies for graphy So it installs graphy for Python 2.6. Can someone help me with it? I just want to set my default easy_install Python version to 2.7.

  Read the article

• Ruckus wireless AP and Dell PowerConnect configuration problems

  - by DanielJay

  We are working on trying to get some Ruckus Access Points to work correctly on our network. Currently our network is as follows: VLAN 10 - Servers VLAN 11 – Computers/DHCP VLAN 12 – Voice VLAN 13 – Guest We use Dell PowerConnect 6248P switches for our switches. Port settings are as follows: ZoneDirector 1100 is plugged into this port. Should be accessing the server VLAN and then allowing all other traffic. interface ethernet 1/g2 classofservice trust ip-dscp description 'Ruckus ZoneDirector 1100' switchport mode general switchport general pvid 10 switchport general allowed vlan add 10 switchport general allowed vlan add 11-13 tagged exit Access point is plugged into this port. The port has to be on VLAN 11 in order to get DHCP. interface ethernet 1/g16 classofservice trust ip-dscp description 'Ruckus - IT' switchport mode general switchport general pvid 11 switchport general allowed vlan add 10-12 switchport general allowed vlan add 13 tagged exit If we tag the traffic from the SSID as VLAN 11 data fails. If we leave the SSID tagged as 1 the data flows correctly. Are there problems with passing tagged traffic to untagged ports? We are looking to see what we can do to get the SSID tagged as 11 instead of 1. Any suggestions?

  Read the article

• Auto-rebuild RAID6 with MDADM

  - by user65632

  Hello everybody, i'm new in this forum, and because I see that a lot of people get helped here, i'll ask my question here! I have a openSUSE 11.3 Linux computer with 5 disks of 1TB (WD enterprise disks) in it. with mdadm I configured an RAID6 device. Now, after a lot of thorough testing, i've noticed that when the computer goes down unsuspectedly it could happen (1 time out of 10) that while booting, the md0 device isn't recognised, and then the machine goes in "recovery mode", which means that i have to 'CTRL + C' it so it can boot to openSUSE. Once in openSUSE i have to readd the drive manually with 'mdadm /dev/md0 --add /dev/sdX'. After this everything works back fine (after resynching). So my question is: Is there a way to auto-rebuild the RAID6 device when there are problems? and how can I stop this "recovery mode" from happening. Because the computer will be in a place I can't go to, to connect a keyboard, 'CTRL + C' it just to get in openSUSE. If you could help me, I would be a very very very! happy man! :-) thanks in advance! Mikhail

  Read the article

• Debian DNSSEC - howto secure a domain?

  - by Daniel Marschall

  I have a beginner question about DNSSEC. I have much experience with TLS and cryptography-stuff and would like to try out this new technology. I have googled very much about this but I haven't found useful information for me. I think one confusion in information gathering is that "Debian howto DNSSEC setup" can mean "How to USE DNSSEC for resolving" OR "How to secure your domain with DNSSEC". I am searching the second. I am running a Debian Squeeze server with root privileges which has a domain name ending with ".de" (which is already signed by the root zone). The network interface at this server uses the gateway IP (DNS resolver?) of the datacentre the server is running on. My domain is hosted at freedns.afraid.org , where I can add DNS RRs for my domain. They are currently NOT capable of adding DNSSEC RRs, but I am bugging them to support this soon. ;-) My simple question is: How do I setup DNSSEC on Debian? Resp. who have I ask to? As far as I understand, all I have to do is to run dnssec-keygen on my Debian server and then add the key to my DNS-provider as DNSSEC RR. (And change it every 30 days?) I have looked at this http://www.isc.org/files/DNSSEC_in_6_minutes.pdf but it looks like you have to be the owner of a ZONE, so I don't think this applies to me. Who needs to sign my domain? My DNS-provider or my zone (DeNIC) or can I do it myself? Any help is very appreciated!

  Read the article

• Workstations cannot see new MS Server 2008 domain, but can access DHCP. (solved)

  - by Radix

  The XP Pro workstations do not see the new replacement domain upon boot; they only see their cached entry for the old (server 2003) domain controller. The old_server is not connected to the network. I have DHCP working with the same scope as the old_server. In my "before-asking" search for a solution I came across the following two articles, and I recall doing things as suggested by the articles. http://www.windowsreference.com/windows-server-2008/how-to-setup-dhcp-server-in-windows-server-2008-step-by-step-guide/ http://www.windowsreference.com/windows-server-2008/step-by-step-guide-for-windows-server-2008-domain-controller-and-dns-server-setup/ The only possible issue is: I was under the impression that the domain netbios needed to match the DC's netbios. The DC netbios is city01 while the domain's FQDN is city.domain.org (I think this is mistaken and should have been just domain.org) But, the second link led me to a post which I believe answers my question. I did as they instructed by opening Local Area Connection Properties, then selecting TCP/IPv4 and setting the sole preferred DNS server to the local hosts static IP (10.10.1.1). Search for "Your problems should clear up" for the post I'm referencing: http://forums.techarena.in/active-directory/1032797.htm Have I misunderstood their instructions? I am hoping to reach the point where I can define users and user groups. Also, does TechNet have a single theoretical overview document I could read. I really don't like treating comps as magic. I will be watching this closely and will quickly answer any questions. If I've left anything out it is because I did not know it was needed. PS: I am loath to ask obviously basic questions, but I am tired and wish to fix this before tomorrow. Also, this is my first server installation, thank you for your help.

  Read the article

• How to debug slow queries in Django+Postgres

  - by lacker

  My database queries from Django are starting to take 1-2 seconds and I'm having trouble figuring out why. Not too big a site, about 1-2 requests per second (that hit Django; static files are just served from nginx.) The thing that confuses me is, I can replicate the slowness in the Django shell using debug mode. But when I issue the exact same queries at an sql prompt they are fast. It takes about a second for a query to return, but when I check connection.queries it reports the time as under 10 ms. Here's an example (from the Django shell): >>> p = PlayerData.objects.get(uid="100000521952372") >>> a = time.time(); p.save(); print time.time() - a 1.96812295914 >>> for d in connection.queries: print d["time"] ... 0.002 0.000 0.000 How can I figure out where this extra time is being spent? I'm using Apache+mod_wsgi in daemon mode, but this happens with just the django shell as well, so I figure it is not apache-related.

  Read the article

• How to set up the jdbc driver to connect to hsqldb from libreoffice?

  - by rumtscho

  I am trying to "split" a LibreOffice .odb file into a HSQL database and an OpenOffice document containing forms and macros. I am trying to follow the instructions from this thread: Within a few minutes you can convert your embedded HSQLDB to a stand-alone HSQLDB which is just a very fine database engine. 1) Download and extract the current version from http://hsqldb.org/ and point the Java class path in ToolsOptionsJava to the new hsqldb.jar 2) Extract the database folder from your embedded database and rename the files data, properties, script to name.data name.properties, name.script where "name." is an arbitrary name prefix. 3) Connect a Base document to an existing JDBC database such as jdbc:hsqldb:file:/home/chenier/hsqldb/name;default_schema=true;shutdown=true;hsqldb.default_table_type=cached;get_column_name=false (again, "name" refers to your own file name prefix). This local single-user connection gives you much more than the embedded HSQLDB. 4) Copy queries, forms and reports from the old database over to the new one. The wizard presents me with a window expecting two inputs: a "Datasource URL" and a "JDBC driver class". As far as I can tell, the tutorial above only tells me what to put into the Datasource URL. As for the JDBC driver class, I have no idea what to write into this field. I tried the fully-qualified name of the Java class, org.hsqldb.jdbc.JDBCDriver as given in the HSQLDB documentation. When that failed, I tried the physical path /var/lib/hsqldb/lib/hsqldb.jar (although that should have been unnecessary, because first I pointed to this path as described under 1 and then restarted LibreOffice). In both cases, "Test class" failed with the message "The JDBC driver could not be loaded". OpenOffice's documentation doesn't say anything sensible about the field, it was something like "enter the JDBC driver in this box". Any ideas what I should enter there to get the connection working?

  Read the article

• Why is my filesystem being mounted read-only in linux?

  - by Tim

  I am trying to set up a small linux system based on Gentoo on a VirtualBox machine, as a step towards deploying the same system onto a low-spec Single Board Computer. For some reason, my filesystem is being mounted read-only. In my /etc/fstab, I have: /dev/sda1 / ext3 defaults 0 0 none /proc proc defaults 0 0 none /sys sysfs defaults 0 0 none /dev/shm tmpfs defaults 0 0 However, once booted /proc/mounts shows rootfs / rootfs rw 0 0 /dev/root / ext3 ro,relatime,errors=continue,barrier=0,data=writeback 0 0 proc /proc proc rw,nosuid,nodev,noexec,relatime 0 0 sysfs /sys sysfs rw,nosuid,nodev,noexec,relatime 0 0 udev /dev tmpfs rw,nosuid,relatime,size=10240k,mode=755 0 0 devpts /dev/pts devpts rw,nosuid,noexec,relatime,gid=5,mode=620 0 0 none /dev/shm tmpfs rw,relatime 0 0 usbfs /proc/bus/usb usbfs rw,nosuid,noexec,relatime,devgid=85,devmode=664 0 0 binfmt_misc /proc/sys/fs/binfmt_misc binfmt_misc rw,nosuid,nodev,noexec,relatime 0 0 (the above may contain errors: there's no practical way to copy and paste) The partition at /dev/hda1 is clearly being mounted OK, since I can read all the data, but it's not being mounted as described in fstab. How might I go about diagnosing / resolving this? Edit: I can remount with mount -o remount,rw / and it works as expected, except that /proc/mounts reports /dev/root mounted at / rather than /dev/sda1 as I'd expect. If I try to remount with mount -a I get mount: none already mounted or /sys busy mount: according to mtab, sysfs is already mounted on /sys Edit 2: I resolved the problem with mount -a (the same error was occuring during startup, it turned out) by changing the sysfs and proc lines to proc /proc proc [...] sysfs /sys sysfs [...] Now mount -a doesn't complain, but it doesn't result in a read-write root partition. mount -o remount / does cause the root partition to be remounted, however.

  Read the article

• Is there a Windows 7 compatible IPSec VPN client that allows protocol and port specific rules?

  - by Sani Huttunen

  As the title says, I need to find a IPSec VPN client for Windows 7. On XP and Vista we've used SafeNet SoftRemote in which you can set up rules for specific protocols and ports. But SoftRemote isn't compatible with Windows 7. 172.xxx.xxx.1 TCP 1433 172.xxx.xxx.2 TCP 1433 172.xxx.xxx.10 ALL ... Since the VPN gateway is configured this way the client must mirror these settings. I've tried TheGreenBow, NCP Secure Entry, Cisco VPN Client and Shrew Soft VPN but none of these allows you to configure by protocol and port. Does anyone have any other suggestions? EDIT: Forgot to mention that agressive mode is also a requirement. --UPDATE-- I've got some news... I've managed to get SoftRemote to work on Windows 7 x64 through Windows XP Mode. After scouring all corners of the Internet for idéas I had enough information to construct a working solution. This solution will probably benefit other clients as well! You'll find a post here with detailed instructions of how I went about.

  Read the article

• Sound out of sync after merging multiple mp4 files with Avidemux

  - by Goto10

  I am trying to join (merge) two or more .mp4 files together, without re-encoding. Here is what I did: Started Avidemux 2.5.5. With File-Open, selected Input1.mp4. I received this message - "H.264 detected. If the file is using B-frames as reference it can lead to a crash or stuttering. Avidemux can use another mode which is safe but YOU WILL LOOSE SOME FRAME ACCURACY. Do you want to use that mode?". I chose "No". With File-Append, selected Input2.mp4. I received the same "H.264 detected" message again and chose "No". Selected the Format to MP4 (from AVI). Saved the output file (called Output.mp4) with File-Save-Save Video. Unfortunately, when I play the Output.mp4 video in VLC, the sound is out of sync with the second video. How can I correct this?

  Read the article

• VPN issue: SSTP Service service started and then stopped

  - by Ampersand

  When I was trying to set up a VPN connect on my laptop running Windows 7 Ultimate, I got this error: Network Connections Cannot load the Remote Access Connection Manager service. Error 711: The operation could not finish because it could not start the Remote Access Connection Manager service in time. Please try the operation again. I traced through some service dependencies and discovered that Secure Socket Tunneling Protocol Service was set to Manual. However, when I try to manually start the service, I get: Services The Secure Socket Tunneling Protocol Service on Local Computer started and then stopped. Some services stop automatically if they are not in use by other services or programs. Setting all the services involved to Automatic did not help. SSTP just showed Automatic and Stopped in the Services panel. I found a solution that involved booting in Safe Mode and deleting the contents of C:\Windows\System32\LogFiles\WMI\RtBackup. This solution worked, and I could set up a vpn connection, but only until I rebooted again. TL;DR I'm looking for a way to permanently enable Secure Socket Tunneling Protocol Service and other vpn-related services permanently so I don't have to reboot into safe mode and delete files every time I need to connect to a vpn.

  Read the article

< Previous Page | 300 301 302 303 304 305 306 307 308 309 310 311  | Next Page >